54ABT244W-QML

MICROCIRCUIT DATA SHEET MN54ABT244-X REV 0B0 Original Creation Date: 09/02/94 Last Update Date: 09/24/98 Last Major Revision Date: 03/19/97 OCTAL BUFFER AND LINE DRIVER WITH TRI-STATE OUTPUTS General Description The ABT244 is an octal buffer and line driver with TRI-STATE outputs designed to be employed as a memory and address driver, clock driver or bus-oriented transmitter/receiver. Industry Part Number 54ABT244 NS Part Numbers 54ABT244E-QML * 54ABT244E-QMLV** 54ABT244J-QML *** 54ABT244J-QMLV**** 54ABT244W-QML ***** 54ABT244W-QMLV****** Prime Die NB244 Controlling Document See Features Page Processing MIL-STD-883, Method 5004 Subgrp Description 1 2 3 4 5 6 7 8A 8B 9 10 11 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 Quality Conformance Inspection MIL-STD-883, Method 5005 1 MN54ABT244-X REV 0B0 MICROCIRCUIT DATA SHEET Features Non-inverting buffers. Output sink capability 48mA, source capability of 24mA Guaranteed latchup protection High impedance glitch free bus loading during entire power up and power down cycle Nondestructive hot insertion capability SMD : 5962-9214701Q2A*, V2A**, QRA***, VRA****, QSA*****, VSA****** 2 MN54ABT244-X REV 0B0 MICROCIRCUIT DATA SHEET (Absolute Maximum Ratings) (Note 1) Vcc Pin Potential to Ground Potential -0.5V to +7.0V Input Voltage (Note 2) -0.5V to +7.0V Input Current (Note 2) -30mA to +5.0mA Voltage Applies To Any Output In the Disabled or Power-Off State In The High State Current Applies To Output In The Low State (Max) Junction Temperature (Tj) Ceramic Thermal Resistance Junction-to-Case (Theta JC) Storage Temperature Lead Temperature (Soldering, 10 seconds) ESD Classification Maximum Power Dissipation 500 mW Note 1: Note 2: Absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions is not implied. Either voltage limit or current limit is sufficient to protect inputs. -0.5V to 5.5V -0.5V to Vcc 96mA +175C See Mil-Std 1835 -65C to +150C +300C Class 1 Recommended Operating Conditions Supply Voltage (Vcc) 4.5V to 5.5V Operating Temperature -55C to +125C Minimum Input Edge Rate (dV/dt) Data Input Enable Input Maximum Output Current High Level (Ioh) Low Level (Iol) 50 mV/ns 20 mV/ns -24 mA 48 mA 3 MN54ABT244-X REV 0B0 MICROCIRCUIT DATA SHEET Electrical Characteristics DC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) DC: 4.5V to 5.5V Temp Range: -55C to 125C SYMBOL ICCH ICCL ICCZ ICCT PARAMETER Supply Current Supply Current Supply Current Supply Current CONDITIONS VCC=5.5V, VINH=5.5V, VINL=0.0V VCC=5.5V, VINH=5.5V, VINL=0.0V VCC=5.5V, VINH=5.5V, VINL=0.0V VCC=5.5V, OE=0.0V Input under test=3.4V Other inputs=5.5V or 0.0V VCC=5.5V, OE=3.4V Other inputs=5.5V or 0.0V VCC=5.5V, OE=5.5V Input under test=3.4V Other inputs=5.5V or 0.0V IIH IIL IOZH High Level Input Current Low Level Input Current Maximum TRI-STATE Leakage Current HIGH Maximum TRI-STATE Leakage Current LOW Output High Leakage Current Output Short Circuit Current Output Short Circuit Current Input High Current Breakdown Test Bus Drainage Test Low Level Output Voltage VCC=5.5V, VINH=5.5V VCC=5.5V, VINL=0.0V VCC=5.5V, VOUT=2.7V VINL=0.0V, VIH (OE)=2.0V VCC=5.5V, VOUT=0.5V VINH=5.5V, VIH (OE)=2.0V VCC=5.5V, VOUT=5.5V VINH=5.5V VCC=5.5V, VOUT=0.0V VINH=5.5V NOTES PINNAME MIN MAX 250.0 30.0 250.0 2.5 2.5 50.0 2.0 -2.0 10.0 UNIT uA mA uA mA mA uA uA uA uA SUBGROUPS 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 4 VCC 1, 4 VCC 1, 4 VCC 1, 4 VCC 1, 4 VCC 1, 4 VCC 1, 4 IN 1, 4 IN 1, 4 OUT IOZL 1, 4 OUT -10.0 uA ICEX IOS 1, 4 OUT 1, 4, 10 1, 4, 10 OUT -100 50.0 -275 uA mA IOS1 VCC=5.5V, VOUT=2.5V VINH=5.5V OUT -50 -180 mA IBVI VCC=5.5V, VINH=7.0V 1, 4 OUT 7.0 uA IZZ VOL VCC=0.0V, VOUT=4.5V, VINL=0.0V VCC=4.5V, IOL=48.0mA, VINH=4.5V, VINL=0.0V, VIH=2.0V, VIL=0.8V 1, 4 OUT 1, 4 OUT -100 100 0.55 uA V 4 MN54ABT244-X REV 0B0 MICROCIRCUIT DATA SHEET Electrical Characteristics DC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: 4.5V to 5.5V Temp Range: -55C to 125C SYMBOL VOH PARAMETER High Level Output Voltage CONDITIONS VCC=4.5V, IOH=-24.0mA, VINH=4.5V, VINL=0.0V, VIH=2.0V, VIL=0.8V VCC=4.5V, IOH=-3mA, VINH=4.5V, VINL=0.0V, VIH=2.0V, VIL=0.8V VCC=5.0V, IOH=-3mA, VINH=5.0V, VINL=0.0V, VIH=2.0V, VIL=0.8V VID VCD VOLP VOLV VOHP VOHV CIN COUT Input Leakage Test Input Clamp Diode Voltage Low Level Ground Bounce Low Level Ground Bounce High Level VCC Bounce High Level VCC Bounce Input Capacitance Output Capacitance VCC=0.0V, IID=1.9uA, VINL=0.0V VCC=4.5V, IKL=-18mA, VINH=4.5V, VINL=0.0V VCC=5.0V, LOAD : 50pF / 500 OHMS VCC=5.0V, LOAD : 50pF / 500 OHMS VCC=5.0V, LOAD : 50pF / 500 OHMS VCC=5.0V, LOAD : 50pF / 500 OHMS VCC=0.0V VCC=5.5V NOTES PINNAME MIN 2.0 2.5 3.0 4.75 -1.2 1.2 -1.8 1.5 -1.1 11.0 16.0 MAX UNIT V V V V V V V V V pF pF SUBGROUPS 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 4 4 4 4 4 4 1, 4 OUT 1, 4 OUT 1, 4 OUT 1, 4 IN 1, 4 IN 7, 8 IN 7, 8 IN 7, 8 IN 7, 8 IN 7 7 IN OUT 5 MN54ABT244-X REV 0B0 MICROCIRCUIT DATA SHEET Electrical Characteristics AC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) AC: CL=50pF RL=500 OHMS TRISE/TFALL = 3.0nS SYMBOL tpLH PARAMETER Propagation Delay CONDITIONS VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C NOTES PINNAME MIN 1.0 1.0 1.0 1.0 2.1 1.2 1.1 0.8 2.1 1.2 1.5 1.0 MAX 4.1 5.3 4.2 5.0 5.6 7.9 5.5 6.5 5.6 7.6 5.6 7.9 UNIT ns ns ns ns ns ns ns ns ns ns ns ns SUBGROUPS 9 10, 11 9 10, 11 9 10, 11 9 10, 11 9 10, 11 9 10, 11 2, 5 In to On 2, 5 In to On tpHL Propagation Delay VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C 2, 5 In to On 2, 5 In to On tpZL Output Enable Time VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C 2, 5 OE to On 2, 5 OE to On tpZH Output Enable Time VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C 2, 5 OE to On 2, 5 OE to On tpHZ Output Disable Time VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C 2, 5 OE to On 2, 5 OE to On tpLZ Output Disable Time VCC=5.0V @25C, VCC=4.5V & 5.5V @-55C/125C 2, 5 OE to On 2, 5 OE to On Note 1: Note 2: Note 3: Note 4: Note 5: Note 6: Note 7: Note 8: SCREEN TESTED 100% ON EACH DEVICE AT -55C, +125C & +25C TEMP., SUBGROUPS 1,2,3,7 & 8. SCREEN TESTED A11. SCREEN TESTED SAMPLE TESTED SUBGROUPS A1, SAMPLE TESTED SUBGROUPS A9, SAMPLE TESTED 100% ON EACH DEVICE AT -55C, +25C & +125C TEMP., SUBGROUPS A9, A10 & 100% ON EACH DEVICE (METHOD 5005, TABLE 2, 3, 7 & 8. (METHOD 5005, TABLE 10, & 11. (METHOD 5005, TABLE AT +25C TEMP. ONLY, SUBGROUP 9. 1) ON EACH MFG. LOT AT +25C, +125C & -55C TEMP., 1) ON EACH MFG. LOT AT +25C, +125C & -55C TEMP., 1) ON EACH MFG. LOT AT +25C TEMP ONLY, SUBGROUP A9. NOT TESTED (GUARANTEED BY DESIGN CHARACTERIZATION DATA). MAX NUMBER OF OUTPUTS DEFINED AS (N). N-1 DATA INPUTS ARE DRIVEN 0V TO 3.0V. ONE OUTPUT @ VOL OR @ VOH. Note 9: MAX NUMBER OF DATA INPUTS (N) SWITCHING. (N-1) INPUTS SWITCHING 0V TO 3.0V. INPUT-UNDERTEST SWITCHING: 3V TO THRESHOLD (VILD), 0V TO THRESHOLD (VIHD), FREQ.= 1 MHZ. Note 10: MAXIMUM TEST DURATION NOT TO EXCEED ONE SECOND, NOT MORE THAN ONE OUTPUT SHORTED AT ONE TIME. 6 MN54ABT244-X REV 0B0 MICROCIRCUIT DATA SHEET Graphics and Diagrams GRAPHICS# E20ARE J20ARM P000062A P000063A W20ARF DESCRIPTION LCC (E), TYPE C, 20 TERMINAL(P/P DWG) CERDIP (J), 20 LEAD (P/P DWG) (new) (new) CERPACK (W), 20 LEAD (P/P DWG) See attached graphics following this page. 7 MN54ABT244-X REV 0B0 MICROCIRCUIT DATA SHEET Revision History Rev 0B0 ECN # Rel Date Originator Bill Petcher Changes Changed MDS MN54ABT244-X REV 0A0 0B0 to MN54ABT244-X REV M0001565 09/24/98 8