LM7808CMDC

LM340/LM78XX Series 3-Terminal Positive Regulators November 2004 LM340/LM78XX Series 3-Terminal Positive Regulators General Description The LM140/LM340A/LM340/LM78XXC monolithic 3-terminal positive voltage regulators employ internal current-limiting, thermal shutdown and safe-area compensation, making them essentially indestructible. If adequate heat sinking is provided, they can deliver over 1.0A output current. They are intended as fixed voltage regulators in a wide range of applications including local (on-card) regulation for elimination of noise and distribution problems associated with single-point regulation. In addition to use as fixed voltage regulators, these devices can be used with external components to obtain adjustable output voltages and currents. Considerable effort was expended to make the entire series of regulators easy to use and minimize the number of external components. It is not necessary to bypass the output, although this does improve transient response. Input bypassing is needed only if the regulator is located far from the filter capacitor of the power supply. The 5V, 12V, and 15V regulator options are available in the steel TO-3 power package. The LM340A/LM340/LM78XXC series is available in the TO-220 plastic power package, and the LM340-5.0 is available in the SOT-223 package, as well as the LM340-5.0 and LM340-12 in the surface-mount TO263 package. Features n Complete specifications at 1A load n Output voltage tolerances of ± 2% at Tj = 25˚C and ± 4% over the temperature range (LM340A) n Line regulation of 0.01% of VOUT/V of ∆VIN at 1A load (LM340A) n Load regulation of 0.3% of VOUT/A (LM340A) n Internal thermal overload protection n Internal short-circuit current limit n Output transistor safe area protection n P+ Product Enhancement tested Typical Applications Fixed Output Regulator Adjustable Output Regulator 00778102 00778101 *Required if the regulator is located far from the power supply filter. **Although no output capacitor is needed for stability, it does help transient response. (If needed, use 0.1 µF, ceramic disc). VOUT = 5V + (5V/R1 + IQ) R2 5V/R1 > 3 IQ, load regulation (Lr) ≈ [(R1 + R2)/R1] (Lr of LM340-5). Current Regulator Comparison between SOT-223 and D-Pak (TO-252) Packages 00778103 00778138 Scale 1:1 ∆IQ = 1.3 mA over line and load changes. © 2004 National Semiconductor Corporation DS007781 www.national.com LM340/LM78XX Ordering Information Package 3-Lead TO-3 Temperature Range -55˚C to +125˚C Part Number LM140K-5.0 LM140K-12 LM140K-15 0˚C to +125˚C LM340K-5.0 LM340K-12 LM340K-15 3-lead TO-220 0˚C to +125˚C LM340AT-5.0 LM340T-5.0 LM340T-12 LM340T-15 LM7808CT 3-Lead TO-263 0˚C to +125˚C LM340S-5.0 LM340SX-5.0 LM340S-12 LM340SX-12 LM340AS-5.0 LM340ASX-5.0 4-Lead SOT-223 Unpackaged Die 0˚C to +125˚C −55˚C to 125˚C LM340MP-5.0 LM340MPX-5.0 LM140KG-5 MD8 LM140KG-12 MD8 LM140KG-15 MD8 0˚C to +125˚C LM340-5.0 MDA LM7808C MDC Packaging Marking LM140K 5.0P+ LM140K 12P+ LM140K 15P+ LM340K 5.0 7805P+ LM340K 12 7812P+ LM340K 15 7815P+ LM340AT 5.0 P+ LM340T5 7805 P+ LM340T12 7812 P+ LM340T15 7815 P+ LM7808CT LM340S-5.0 P+ LM340S-12 P+ LM340AS-5.0 P+ N00A Transport Media 50 Per Tray 50 Per Tray 50 Per Tray 50 Per Tray 50 Per Tray 50 Per Tray 45 Units/Rail 45 Units/Rail 45 Units/Rail 45 Units/Rail 45 Units/Rail 45 Units/Rail 500 Units Tape and Reel 45 Units/Rail 500 Units Tape and Reel 45 Units/Rail 500 Units Tape and Reel 1k Units Tape and Reel 2k Units Tape and Reel Waffle Pack or Gel Pack Waffle Pack or Gel Pack Waffle Pack or Gel Pack Waffle Pack or Gel Pack Waffle Pack or Gel Pack DL069089 DL059093 DL059093 DI074056 DI074056 MP04A TS3B T03B NSC Drawing K02A Connection Diagrams TO-3 Metal Can Package (K) TO-220 Power Package (T) 00778111 00778112 Bottom View See Package Number K02A TO-263 Surface-Mount Package (S) Top View See Package Number T03B 3-Lead SOT-223 00778120 00778143 Top View See Package Number TS3B Top View See Package Number MP04A www.national.com 2 LM340/LM78XX Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. (Note 5) DC Input Voltage Internal Power Dissipation (Note 2) Maximum Junction Temperature Storage Temperature Range Lead Temperature (Soldering, 10 sec.) TO-3 Package (K) 300˚C 35V Internally Limited 150˚C −65˚C to +150˚C TO-220 Package (T), TO-263 Package (S) ESD Susceptibility (Note 3) 230˚C 2 kV Operating Conditions (Note 1) Temperature Range (TA) (Note 2) LM140 LM340A, LM340 LM7808C −55˚C to +125˚C 0˚C to +125˚C 0˚C to +125˚C LM340A Electrical Characteristics IOUT = 1A, 0˚C ≤ TJ ≤ + 125˚C (LM340A) unless otherwise specified (Note 4) Output Voltage Symbol VO Input Voltage (unless otherwise noted) Parameter Output Voltage TJ = 25˚C PD ≤ 15W, 5 mA ≤ IO ≤ 1A VMIN ≤ VIN ≤ VMAX ∆V O Line Regulation IO = 500 mA ∆VIN TJ = 25˚C ∆VIN TJ = 25˚C Over Temperature ∆VIN ∆V O Load Regulation TJ = 25˚C 5 mA ≤ IO ≤ 1.5A 250 mA ≤ IO ≤ 750 mA Over Temperature, 5 mA ≤ IO ≤ 1A IQ Quiescent Current Quiescent Current Change TJ = 25˚C Over Temperature ∆I Q 5 mA ≤ IO ≤ 1A TJ = 25˚C, IO = 1A VMIN ≤ VIN ≤ VMAX IO = 500 mA VMIN ≤ VIN ≤ VMAX VN Output Noise Voltage Ripple Rejection TA = 25˚C, 10 Hz ≤ f ≤ 100 kHz TJ = 25˚C, f = 120 Hz, IO = 1A or f = 120 Hz, IO = 500 mA, Over Temperature, VMIN ≤ VIN ≤ VMAX RO Dropout Voltage Output Resistance Short-Circuit Current TJ = 25˚C, IO = 1A f = 1 kHz TJ = 25˚C (8 ≤ VIN ≤ 18) 2.0 8 2.1 (15 ≤ VIN ≤ 25) 2.0 18 1.5 (18.5 ≤ VIN ≤ 28.5) 2.0 19 1.2 V V mΩ A 68 68 40 80 61 61 0.5 0.8 (7.5 ≤ VIN ≤ 20) 0.8 (8 ≤ VIN ≤ 25) 75 72 60 60 6 6.5 0.5 0.8 (14.8 ≤ VIN ≤ 27) 0.8 (15 ≤ VIN ≤ 30) 90 70 6 6.5 0.5 0.8 (17.9 ≤ VIN ≤ 30) 0.8 (17.9 ≤ VIN ≤ 30) 6 6.5 mA mA mA mA V mA V µV dB dB 10 3 Conditions 4.9 4.8 5V 10V Min Typ Max 5 5.1 5.2 10 (7.5 ≤ VIN ≤ 20) 10 4 12 (8 ≤ VIN ≤ 12) 25 15 25 12 (7.5 ≤ VIN ≤ 20) 4 Min 11.75 11.5 12V 19V Typ Max 12.5 18 (14.8 ≤ VIN ≤ 27) 18 9 30 (16 ≤ VIN ≤ 22) 32 19 60 12 (14.5 ≤ VIN ≤ 27) 4 Min 14.4 12 12.25 14.7 15V 23V Typ Max 15 15.3 15.6 22 (17.9 ≤ VIN ≤ 30) 22 10 30 (20 ≤ VIN ≤ 26) 35 21 75 (17.5 ≤ VIN ≤ 30) V V V mV V mV V mV mV V mV mV mV Units (7.5 ≤ VIN ≤ 20) (14.8 ≤ VIN ≤ 27) (17.9 ≤ VIN ≤ 30) 3 www.national.com LM340/LM78XX LM340A Electrical Characteristics Output Voltage Symbol (Continued) IOUT = 1A, 0˚C ≤ TJ ≤ + 125˚C (LM340A) unless otherwise specified (Note 4) 5V 10V Min Typ Max 2.4 −0.6 Min 12V 19V Typ Max 2.4 −1.5 Min 15V 23V Typ Max 2.4 −1.8 A mV/˚C Units Input Voltage (unless otherwise noted) Parameter Peak Output Current Average TC of VO TJ = 25˚C Min, TJ = 0˚C, IO = 5 mA TJ = 25˚C 7.5 14.5 17.5 V Conditions VIN Input Voltage Required to Maintain Line Regulation LM140 Electrical Characteristics −55˚C ≤ TJ ≤ +150˚C unless otherwise specified Output Voltage Symbol VO (Note 4) 5V 10V Min Typ Max 4.8 4.75 5 5.2 5.25 Min 11.5 11.4 12V 19V 12 12.5 14.4 12.6 14.25 15V 23V 15 Units 15.6 15.75 V V V Input Voltage (unless otherwise noted) Parameter Output Voltage Conditions TJ = 25˚C, 5 mA ≤ IO ≤ 1A PD ≤ 15W, 5 mA ≤ IO ≤ 1A VMIN ≤ VIN ≤ VMAX Typ Max Min Typ Max (8 ≤ VIN ≤ 20) 3 50 (15.5 ≤ VIN ≤ 27) 4 120 (18.5 ≤ VIN ≤ 30) 4 (17.5 ≤ VIN ≤ 30) (18.5 ≤ VIN ≤ 30) (17.7 ≤ VIN ≤ 30) 75 (20 ≤ VIN ≤ 26) 12 75 ∆VO Line Regulation IO = 500 mA TJ = 25˚C ∆VIN −55˚C ≤ TJ ≤ +150˚C ∆VIN 150 mV V (7 ≤ VIN ≤ 25) 50 (8 ≤ VIN ≤ 20) 50 (7.5 ≤ VIN ≤ 20) 25 (8 ≤ VIN ≤ 12) 10 50 25 50 6 7 0.5 0.8 (8 ≤ VIN ≤ 20) 0.8 (8 ≤ VIN ≤ 25) 40 (14.5 ≤ VIN ≤ 30) 120 (15 ≤ VIN ≤ 27) 120 (14.6 ≤ VIN ≤ 27) 60 (16 ≤ VIN ≤ 22) 12 120 60 120 6 7 0.5 0.8 (15 ≤ VIN ≤ 27) 0.8 (15 ≤ VIN ≤ 30) 75 150 mV V IO ≤ 1A TJ = 25˚C ∆VIN −55˚C ≤ TJ ≤ +150˚C ∆VIN 150 mV V mV V mV ∆V O Load Regulation TJ = 25˚C 5 mA ≤ IO ≤ 1.5A 250 mA ≤ IP ≤ 750 mA 150 mV −55˚C ≤ TJ ≤ +150˚C, 5 mA ≤ IO ≤ 1A IQ ∆IQ Quiescent Current Quiescent Current Change IO ≤ 1A TJ = 25˚C −55˚C ≤ TJ ≤ +150˚C 5 mA ≤ IO ≤ 1A TJ = 25˚C, IO ≤ 1A VMIN ≤ VIN ≤ VMAX IO = 500 mA, −55˚C ≤ TJ ≤ +150˚C VMIN ≤ VIN ≤ VMAX VN Output Noise Voltage TA = 25˚C, 10 Hz ≤ f ≤ 100 kHz 150 mV 6 7 0.5 0.8 (18.5 ≤ VIN ≤ 30) 0.8 (18.5 ≤ VIN ≤ 30) 90 mA mA mA mA V mA V µV www.national.com 4 LM340/LM78XX LM140 Electrical Characteristics −55˚C ≤ TJ ≤ +150˚C unless otherwise specified Output Voltage Symbol (Note 4) (Continued) 5V 10V Min Typ Max 68 68 (8 ≤ VIN ≤ 18) 2.0 8 2.1 2.4 −0.6 80 Min 61 61 (15 ≤ VIN ≤ 25) 2.0 18 1.5 2.4 −1.5 12V 19V 72 60 60 (18.5 ≤ VIN ≤ 28.5) 2.0 19 1.2 2.4 −1.8 15V 23V 70 Units dB dB V V mΩ A A mV/˚C Input Voltage (unless otherwise noted) Parameter Ripple Rejection or f = 120 Hz IO ≤ 500 mA, −55˚C ≤ TJ ≤+150˚C VMIN ≤ VIN ≤ VMAX Conditions IO ≤ 1A, TJ = 25˚C Typ Max Min Typ Max RO Dropout Voltage Output Resistance Short-Circuit Current Peak Output Current Average TC of VOUT TJ = 25˚C, IO = 1A f = 1 kHz TJ = 25˚C TJ = 25˚C 0˚C ≤ TJ ≤ +150˚C, IO = 5 mA TJ = 25˚C, IO ≤ 1A 7.5 VIN Input Voltage Required to Maintain Line Regulation 14.6 17.7 V LM340 Electrical Characteristics 0˚C ≤ TJ ≤ +125˚C unless otherwise specified Output Voltage Symbol VO (Note 4) 5V 10V 4.8 4.75 5 5.2 11.5 12V 19V 12 12.5 14.4 12.6 14.25 15V 23V 15 15.6 15.75 Units V V V mV V mV V mV V mV V mV mV mV mA mA mA 1.0 mA Input Voltage (unless otherwise noted) Parameter Output Voltage Conditions TJ = 25˚C, 5 mA ≤ IO ≤ 1A PD ≤ 15W, 5 mA ≤ IO ≤ 1A VMIN ≤ VIN ≤ VMAX Min Typ Max Min Typ Max Min Typ Max 5.25 11.4 (7.5 ≤ VIN ≤ 20) 3 50 (14.5 ≤ VIN ≤ 27) 4 120 (14.5 ≤ VIN ≤ 30) 120 (15 ≤ VIN ≤ 27) 120 (14.6 ≤ VIN ≤ 27) 60 (16 ≤ VIN ≤ 22) 12 120 60 120 8 8.5 0.5 (17.5 ≤ VIN ≤ 30) 4 150 ∆V O Line Regulation IO = 500 mA TJ = 25˚C ∆VIN 0˚C ≤ TJ ≤ +125˚C ∆VIN IO ≤ 1A TJ = 25˚C ∆VIN 0˚C ≤ TJ ≤ +125˚C ∆VIN (7 ≤ VIN ≤ 25) 50 (8 ≤ VIN ≤ 20) 50 (7.5 ≤ VIN ≤ 20) 25 (8 ≤ VIN ≤ 12) 10 50 25 50 8 8.5 0.5 1.0 (17.5 ≤ VIN ≤ 30) 150 (18.5 ≤ VIN ≤ 30) 150 (17.7 ≤ VIN ≤ 30) 75 (20 ≤ VIN ≤ 26) 12 150 75 150 8 8.5 0.5 ∆V O Load Regulation TJ = 25˚C 5 mA ≤ IO ≤ 1.5A 250 mA ≤ IO ≤ 750 mA 5 mA ≤ IO ≤ 1A, 0˚C ≤ TJ ≤ +125˚C IQ ∆I Q Quiescent Current Quiescent Current Change IO ≤ 1A TJ = 25˚C 0˚C ≤ TJ ≤ +125˚C 5 mA ≤ IO ≤ 1A TJ = 25˚C, IO ≤ 1A 1.0 5 www.national.com LM340/LM78XX LM340 Electrical Characteristics 0˚C ≤ TJ ≤ +125˚C unless otherwise specified Output Voltage Symbol (Note 4) (Continued) 5V 10V (7.5 ≤ VIN ≤ 20) 1.0 (7 ≤ VIN ≤ 25) 40 62 62 (8 ≤ VIN ≤ 18) 2.0 8 2.1 2.4 −0.6 7.5 14.6 80 55 55 (15 ≤ VIN ≤ 25) 2.0 18 1.5 2.4 −1.5 17.7 12V 19V (14.8 ≤ VIN ≤ 27) 1.0 (14.5 ≤ VIN ≤ 30) 75 72 54 54 (18.5 ≤ VIN ≤ 28.5) 2.0 19 1.2 2.4 −1.8 15V 23V (17.9 ≤ VIN ≤ 30) 1.0 (17.5 ≤ VIN ≤ 30) 90 70 Units V mA V µV dB dB V V mΩ A A mV/˚C V Input Voltage (unless otherwise noted) Parameter Conditions VMIN ≤ VIN ≤ VMAX IO ≤ 500 mA, 0˚C ≤ TJ ≤ +125˚C VMIN ≤ VIN ≤ VMAX Min Typ Max Min Typ Max Min Typ Max VN Output Noise Voltage Ripple Rejection TA = 25˚C, 10 Hz ≤ f ≤ 100 kHz IO ≤ 1A, TJ = 25˚C f = 120 Hz or IO ≤ 500 mA, 0˚C ≤ TJ ≤ +125˚C VMIN ≤ VIN ≤ VMAX RO Dropout Voltage Output Resistance Peak Output Current TJ = 25˚C, IO = 1A f = 1 kHz TJ = 25˚C Short-Circuit Current TJ = 25˚C Average TC of VOUT 0˚C ≤ TJ ≤ +125˚C, IO = 5 mA VIN Input Voltage Required to Maintain Line Regulation TJ = 25˚C, IO ≤ 1A Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Conditions are conditions under which the device functions but the specifications might not be guaranteed. For guaranteed specifications and test conditions see the Electrical Characteristics. Note 2: The maximum allowable power dissipation at any ambient temperature is a function of the maximum junction temperature for operation (TJMAX = 125˚C or 150˚C), the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA). PDMAX = (TJMAX − TA)/θJA. If this dissipation is exceeded, the die temperature will rise above TJMAX and the electrical specifications do not apply. If the die temperature rises above 150˚C, the device will go into thermal shutdown. For the TO-3 package (K, KC), the junction-to-ambient thermal resistance (θJA) is 39˚C/W. When using a heatsink, θJA is the sum of the 4˚C/W junction-to-case thermal resistance (θJC) of the TO-3 package and the case-to-ambient thermal resistance of the heatsink. For the TO-220 package (T), θJA is 54˚C/W and θJC is 4˚C/W. If SOT-223 is used, the junction-to-ambient thermal resistance is 174˚C/W and can be reduced by a heatsink (see Applications Hints on heatsinking). If the TO-263 package is used, the thermal resistance can be reduced by increasing the PC board copper area thermally connected to the package: Using 0.5 square inches of copper area, θJA is 50˚C/W; with 1 square inch of copper area, θJAis 37˚C/W; and with 1.6 or more inches of copper area, θJA is 32˚C/W. Note 3: ESD rating is based on the human body model, 100 pF discharged through 1.5 kΩ. Note 4: All characteristics are measured with a 0.22 µF capacitor from input to ground and a 0.1 µF capacitor from output to ground. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tw ≤ 10 ms, duty cycle ≤ 5%). Output voltage changes due to changes in internal temperature must be taken into account separately. Note 5: Military datasheets are available upon request. At the time of printing, the military datasheet specifications for the LM140K-5.0/883, LM140K-12/883, and LM140K-15/883 complied with the min and max limits for the respective versions of the LM140. The LM140H and LM140K may also be procured as JAN devices on slash sheet JM38510/107. www.national.com 6 LM340/LM78XX LM7808C Electrical Characteristics 0˚C ≤ TJ ≤ +150˚C, VI = 14V, IO = 500 mA, CI = 0.33 µF, CO = 0.1 µF, unless otherwise specified Symbol VO ∆V O ∆V O Parameter Output Voltage Line Regulation Load Regulation TJ = 25˚C TJ = 25˚C TJ = 25˚C 10.5V ≤ VI ≤ 25V 11.0V ≤ VI ≤ 17V 5.0 mA ≤ IO ≤ 1.5A 250 mA ≤ IO ≤ 750 mA VO IQ ∆I Q VN ∆VI/∆VO VDO RO IOS IPK ∆VO/∆T Output Voltage Quiescent Current Quiescent Current Change Noise Ripple Rejection Dropout Voltage Output Resistance Output Short Circuit Current Peak Output Current Average Temperature Coefficient of Output Voltage Note 6: All characteristics are measured with a 0.22 µF capacitor from input to ground and a 0.1 µF capacitor from output to ground. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tw ≤ 10 ms, duty cycle ≤ 5%). Output voltage changes due to changes in internal temperature must be taken into account separately. Conditions (Note 6) Min 7.7 LM7808C Typ 8.0 6.0 2.0 12 4.0 7.6 4.3 Max 8.3 160 80 160 80 8.4 8.0 1.0 0.5 52 56 72 2.0 16 0.45 2.2 0.8 Units V mV mV 11.5V ≤ VI ≤ 23V, 5.0 mA ≤ IO ≤ 1.0A, P ≤ 15W TJ = 25˚C With Line With Load 11.5V ≤ VI ≤ 25V 5.0 mA ≤ IO ≤ 1.0A TA = 25˚C, 10 Hz ≤ f ≤ 100 kHz f = 120 Hz, IO = 350 mA, TJ = 25˚C IO = 1.0A, TJ = 25˚C f = 1.0 kHz TJ = 25˚C, VI = 35V TJ = 25˚C IO = 5.0 mA V mA mA µV dB V mΩ A A mV/˚C 7 www.national.com LM340/LM78XX Typical Performance Characteristics Maximum Average Power Dissipation Maximum Average Power Dissipation 00778122 00778123 Maximum Power Dissipation (TO-263) (See Note 2) Output Voltage (Normalized to 1V at TJ = 25˚C) 00778124 00778125 Note: Shaded area refers to LM340A/LM340, LM7805C, LM7812C and LM7815C. Ripple Rejection Ripple Rejection 00778126 00778127 www.national.com 8 LM340/LM78XX Typical Performance Characteristics Output Impedance (Continued) Dropout Characteristics 00778128 00778129 Quiescent Current Peak Output Current 00778130 00778131 Note: Shaded area refers to LM340A/LM340, LM7805C, LM7812C and LM7815C. Dropout Voltage Quiescent Current 00778132 Note: Shaded area refers to LM340A/LM340, LM7805C, LM7812C and LM7815C. 00778133 9 www.national.com LM340/LM78XX Line Regulation 140AK-5.0, IOUT = 1A, TA = 25˚C Line Regulation 140AK-5.0, VIN = 10V, TA = 25˚C 00778105 00778106 Equivalent Schematic 00778107 www.national.com 10 LM340/LM78XX Application Hints The LM340/LM78XX series is designed with thermal protection, output short-circuit protection and output transistor safe area protection. However, as with any IC regulator, it becomes necessary to take precautions to assure that the regulator is not inadvertently damaged. The following describes possible misapplications and methods to prevent damage to the regulator. SHORTING THE REGULATOR INPUT When using large capacitors at the output of these regulators, a protection diode connected input to output (Figure 1) may be required if the input is shorted to ground. Without the protection diode, an input short will cause the input to rapidly approach ground potential, while the output remains near the initial VOUTbecause of the stored charge in the large output capacitor. The capacitor will then discharge through a large internal input to output diode and parasitic transistors. If the energy released by the capacitor is large enough, this diode, low current metal and the regulator will be destroyed. The fast diode in Figure 1 will shunt most of the capacitors discharge current around the regulator. Generally no protection diode is required for values of output capacitance ≤ 10 µF. RAISING THE OUTPUT VOLTAGE ABOVE THE INPUT VOLTAGE Since the output of the device does not sink current, forcing the output high can cause damage to internal low current paths in a manner similar to that just described in the “Shorting the Regulator Input” section. REGULATOR FLOATING GROUND (Figure 2) When the ground pin alone becomes disconnected, the output approaches the unregulated input, causing possible damage to other circuits connected to VOUT. If ground is reconnected with power “ON”, damage may also occur to the regulator. This fault is most likely to occur when plugging in regulators or modules with on card regulators into powered up sockets. Power should be turned off first, thermal limit ceases operating, or ground should be connected first if power must be left on. TRANSIENT VOLTAGES If transients exceed the maximum rated input voltage of the device, or reach more than 0.8V below ground and have sufficient energy, they will damage the regulator. The solution is to use a large input capacitor, a series input breakdown diode, a choke, a transient suppressor or a combination of these. 00778108 FIGURE 1. Input Short 00778109 FIGURE 2. Regulator Floating Ground 00778110 FIGURE 3. Transients When a value for θ(H–A) is found using the equation shown, a heatsink must be selected that has a value that is less than or equal to this number. θ(H–A) is specified numerically by the heatsink manufacturer in this catalog, or shown in a curve that plots temperature rise vs power dissipation for the heatsink. 11 www.national.com LM340/LM78XX Application Hints (Continued) HEATSINKING TO-263 AND SOT-223 PACKAGE PARTS Both the TO-263 (“S”) and SOT-223 (“MP”) packages use a copper plane on the PCB and the PCB itself as a heatsink. To optimize the heat sinking ability of the plane and PCB, solder the tab of the plane. shows for the TO-263 the measured values of θ(J–A) for different copper area sizes using a typical PCB with 1 ounce copper and no solder mask over the copper area used for heatsinking. Figures 6, 7 show the information for the SOT-223 package. Figure 6 assumes a θ(J–A) of 74˚C/W for 1 ounce copper and 51˚C/W for 2 ounce copper and a maximum junction temperature of 125˚C. 00778141 FIGURE 6. θ(J–A) vs Copper (2 ounce) Area for the SOT-223 Package 00778139 FIGURE 4. θ(J–A) vs Copper (1 ounce) Area for the TO-263 Package As shown in the figure, increasing the copper area beyond 1 square inch produces very little improvement. It should also be observed that the minimum value of θ(J–A) for the TO-263 package mounted to a PCB is 32˚C/W. As a design aid, Figure 5 shows the maximum allowable power dissipation compared to ambient temperature for the TO-263 device (assuming θ(J–A) is 35˚C/W and the maximum junction temperature is 125˚C). 00778142 FIGURE 7. Maximum Power Dissipation vs TAMB for the SOT-223 Package Please see AN-1028 for power enhancement techniques to be used with the SOT-223 package. 00778140 FIGURE 5. Maximum Power Dissipation vs TAMB for the TO-263 Package www.national.com 12 LM340/LM78XX Typical Applications Fixed Output Regulator 00778113 Note: Bypass capacitors are recommended for optimum stability and transient response, and should be located as close as possible to the regulator. High Input Voltage Circuits 00778114 00778115 High Current Voltage Regulator 00778116 13 www.national.com LM340/LM78XX Typical Applications (Continued) High Output Current, Short Circuit Protected 00778117 Positive and Negative Regulator 00778118 www.national.com 14 LM340/LM78XX Physical Dimensions unless otherwise noted inches (millimeters) TO-3 Metal Can Package (K) NS Package Number K02A TO-263 Surface-Mount Package (S) NS Package Number TS3B 15 www.national.com LM340/LM78XX Physical Dimensions inches (millimeters) unless otherwise noted (Continued) TO-220 Power Package (T) NS Package Number T03B 3-Lead SOT-223 Package NS Package Number MP04A www.national.com 16 LM340/LM78XX Series 3-Terminal Positive Regulators Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.