STK404-070NGEVB

STK404-070NGEVB, STK404-120NGEVB, STK404-140NGEVB STK404-000N Series Evaluation Board User's Manual http://onsemi.com EVAL BOARD USER’S MANUAL Thick-Film Hybrid IC for use used in from 60 W to 180 W × 1ch class AB audio power amplifiers. This Evaluation Board User’s Manual describes the set-up and use of the STK404−000N Series Evaluation Board for SANYO Semiconductor (An ON Semiconductor Company). Thick-Film Hybrid IC for use in from 60 W to 180 W × 1ch class AB audio power amplifiers devices STK404-070N-E, STK404-120N-E and STK404-140N-E. For data sheets and additional on these devices, please visit the ON Semiconductor website at www.onsemi.com. Figure 1. STK404−000N Series Evaluation Board EVALUATION BOARD FOR STK404−070N, −120N, −140N (100 mm × 70 mm × 1.6 mm, Phenol 1-layer Board) (100 mm × 70 mm × 1.6 mm, Phenol 1-layer Board) (100 mm × 70 mm × 1.6 mm, Phenol 1-layer Board) Figure 2. STK404−070NGEVB Figure 3. STK404−120NGEVB Figure 4. STK404−140NGEVB Table 1. SELECTION GUIDE STK404−070N−E STK404−120N−E STK404−140N−E Output1 (10%/1 kHz) 60 W × 1ch 120 W × 1ch 180 W × 1ch Output2 (1%/20 Hz to 20 kHz) 40 W × 1ch 80 W × 1ch 120 W × 1ch Maximum Rating VCC max (no sig.) ±46 V ±65 V ±78 V Maximum Rating VCC (6 W) ±39 V ±59 V ±73 V Recommended Operating VCC (6 W) ±30 V ±41 V ±51 V 44.0 × 25.6 × 8.5 (mm) 46.6 × 25.5 × 8.5 (mm) 59.2 × 25.5 × 8.5 (mm) Package Size © Semiconductor Components Industries, LLC, 2013 June, 2013 − Rev. 0 1 Publication Order Number: EVBUM2197/D STK404−070NGEVB, STK404−120NGEVB, STK404−140NGEVB Constant-voltage Supply Signal Output Load (RL = 6 W) CH1 GND OSC Output (600 W) CH1 Figure 5. Characteristics Confirmation +VCC 10,000 mF 500 W + 500 W −VCC Specified Transformer Power Supply STK404-070N-E (Equivalent to MG-200) STK404-120N-E/140N-E (Equivalent to MG-250) + 10,000 mF Constant-voltage Supply Signal Speaker (CH1) Music Source (CH1) GND Figure 6. Sound Quality Configuration, Load Short-circuit Test, Noise Examination http://onsemi.com 2 STK404−070NGEVB, STK404−120NGEVB, STK404−140NGEVB STK404−000NSR PCB PARTS LIST Table 2. PCB NAME: STK404−000SR GEVB − A Type (IC1) STK404−070N−E STK404−120N−E STK404−140N−E Position of (1)pin Third from the Right End Second from the Right End The Right End 1 kW ← ← R2 56 kW ← ← R3 1.8 kW ← ← R4 100 W/1 W ← ← R5 56 kW ← ← R6 10 kW/1 W 4.7 kW/1 W 5.1 kW/1 W R7 10 kW/1 W 4.7 kW/1 W 5.1 kW/1 W R8 0.22 W/5 W ← ← R9 − 0.22 W/5 W ← R10 4.7 W/1 W ← ← R11 4.7 W/1 W ← ← C1 470 pF ← ← C2 2.2 mF/50 V ← ← C3 10 mF/50 V ← ← C4 100 mF/100 V ← ← C5 5 pF ← ← C6 100 mF/50 V ← ← C7 47 mF/100 V ← ← C8 10 mF/100 V ← ← C9 10 mF/100 V ← ← C10 0.1 mF ← ← D1 200 V/0.5 A Short Short L1 2.2 mH ← ← J1 15 mm ← ← J2 10 mm ← ← Location R1 http://onsemi.com 3 STK404−070NGEVB, STK404−120NGEVB, STK404−140NGEVB TEST CIRCUITS STK404−070N−E 1 R1 IN C1 2 4 5 C4 + C2 3 R3 R2 R4 7 D1 + + C3 6 + 8 9 10 + C8 + R8 C9 R6 C6 R7 C7 +12V +VCC −VCC + C5 R10 L1 R5 OUT C10 RL R11 Figure 7. STK404−070N−E Test Circuit STK404−120N−E 1 2 R1 IN 3 + C2 C1 4 C3 6 C4 R3 R2 5 7 R4 9 C8 + + 8 R6 + 10 11 + + 12 R8 C9 R9 C6 + R7 C5 C7 R10 L1 R5 +12V +VCC −VCC OUT C10 RL R11 Figure 8. STK404−120N−E Test Circuit STK404−140N−E 1 IN 2 R1 C1 3 4 + C2 C3 6 C4 R3 R2 5 + 7 8 9 10 11 12 + R4 + R6 + C8 + C9 13 R8 +12V +VCC −VCC C6 + R7 C5 C7 R10 L1 R5 http://onsemi.com 4 OUT C10 R11 Figure 9. STK404−140N−E Test Circuit R9 RL STK404−070NGEVB, STK404−120NGEVB, STK404−140NGEVB SUBSTRATE SPECIFICATIONS (Substrate Recommended for Operation of STK404-070N/120N/140N) Size: 100 mm × 70 mm × 1.6 mm, Phenol 1-layer Board Material: Phenol Copper Side (35 m) PCB LAYOUT EXAMPLE Figure 10. Top View Figure 11. Top View http://onsemi.com 5 STK404−070NGEVB, STK404−120NGEVB, STK404−140NGEVB CHARACTERISTIC OF EVALUATION BOARD − STK404−070N−E 10 1 60 VCC = ±30 V RL = 6 W 1ch Drive VG = 30 dB Rg = 600 W TC = 25°C Total Device Power Dissipation, Pd (W) Total Harmonic Distortion THD (%) 100 f = 20 kHz 0.1 f = 1 kHz 0.01 0.001 0.1 1 10 VCC = ±30 V f = 1 kHz RL = 6 W 1ch Drive VG = 30 dB Rg = 600 W TC = 25°C 50 40 30 20 10 0 0.1 100 Output Power per Channel, Po/ch (W) 1 1000 Figure 13. Pd vs. Po 120 120 f = 1 kHz RL = 6 W 1ch Drive VG = 30 dB Rg = 600 W TC = 25°C 110 100 90 80 70 THD = 10% (f = 1 kHz) Output Power per Channel, Po/ch (W) Output Power per Channel, Po/ch (W) 100 Output Power per Channel, Po/ch (W) Figure 12. THD vs. Po THD = 0.4% (f = 1 kHz) 60 50 40 30 20 10 0 10 110 100 90 THD = 10% 80 70 THD = 0.4% 60 50 VCC = ±30 V RL = 6 W 1ch Drive VG = 30 dB Rg = 600 W TC = 25°C 40 30 20 10 20 22 24 26 28 30 32 34 36 38 0 40 10 Supply Voltage, VCC (±V) 100 1000 10000 Frequency, f (Hz) Figure 14. Po vs. VCC Figure 15. Po vs. f http://onsemi.com 6 100000 STK404−070NGEVB, STK404−120NGEVB, STK404−140NGEVB CHARACTERISTIC OF EVALUATION BOARD − STK404−120N−E 10 1 100 VCC = ±41 V RL = 6 W 1ch Drive VG = 30 dB Rg = 600 W TC = 25°C Total Device Power Dissipation, Pd (W) Total Harmonic Distortion THD (%) 100 f = 20 kHz 0.1 f = 1 kHz 0.01 0.001 0.1 1 10 100 1000 VCC = ±41 V f = 1 kHz RL = 6 W 1ch Drive VG = 30 dB Rg = 600 W TC = 25°C 90 80 70 60 50 40 30 20 10 0 0.1 Output Power per Channel, Po/ch (W) 1 THD = 10% Output Power per Channel, Po/ch (W) Output Power per Channel, Po/ch (W) 200 THD = 0.4% 100 0 20 30 40 50 1000 Figure 17. Pd vs. Po 300 f = 1 kHz RL = 6 W 1ch Drive VG = 30 dB Rg = 600 W TC = 25°C 100 Output Power per Channel, Po/ch (W) Figure 16. THD vs. Po 300 10 60 200 THD = 10% THD = 1% 100 0 70 VCC = ±41 V RL = 6 W 1ch Drive VG = 30 dB Rg = 600 W TC = 25°C 10 Supply Voltage, VCC (±V) 100 1000 10000 Frequency, f (Hz) Figure 18. Po vs. VCC Figure 19. Po vs. f http://onsemi.com 7 100000 STK404−070NGEVB, STK404−120NGEVB, STK404−140NGEVB CHARACTERISTIC OF EVALUATION BOARD − STK404−140N−E 10 1 160 VCC = ±51 V RL = 6 W 1ch Drive VG = 30 dB Rg = 600 W TC = 25°C Total Device Power Dissipation, Pd (W) Total Harmonic Distortion THD (%) 100 f = 20 kHz 0.1 f = 1 kHz 0.01 0.001 0.1 1 10 100 1000 VCC = ±51 V f = 1 kHz RL = 6 W 1ch Drive VG = 30 dB Rg = 600 W TC = 25°C 140 120 100 80 60 40 20 0 0.1 Output Power per Channel, Po/ch (W) 1 300 f = 1 kHz RL = 6 W 1ch Drive VG = 30 dB Rg = 600 W TC = 25°C THD = 10% THD = 0.4% 100 0 20 30 1000 Figure 21. Pd vs. Po Output Power per Channel, Po/ch (W) Output Power per Channel, Po/ch (W) 200 100 Output Power per Channel, Po/ch (W) Figure 20. THD vs. Po 300 10 40 50 60 THD = 10% 200 VCC = ±51 V RL = 6 W 1ch Drive VG = 30 dB Rg = 600 W TC = 25°C 100 0 70 THD = 1% 10 Supply Voltage, VCC (±V) 100 1000 10000 Frequency, f (Hz) Figure 22. Po vs. VCC Figure 23. Po vs. f http://onsemi.com 8 100000 STK404−070NGEVB, STK404−120NGEVB, STK404−140NGEVB STAND−BY CONTROL & MUTE CONTROL APPLICATION STK404−070N−E STK404−120N−E STK404−140N−E 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 11 12 2 3 4 5 6 7 8 9 10 11 12 13 1 + IN 10kW + + + 10kW + + 2.2kW +12V +VCC −VCC + Mute Control H:Signal Mute L:Normal OUT tdr > 1s SB1 5V Mute 10kW 10kW 5V +12V SB2 SB1 ST−BYMUTE PLAY MUTE ST−BY 10kW 10kW 10kW 10kW 5V SB2 10kW 10kW tdf > 100ms +VCC 6.8kW Vz=13V 12V Regulator Stand−by Control H:Operation Mode L:Stand−by Mode Figure 24. STK404−000−Ese Stand-by Control & Mute Control Application THERMAL SHUT DOWN APPLICATION STK404−070N−E No Thermal Sensor Thermal Sensor STK404−120N−E 1 Shutdown Signal 2 3 4 5 6 7 8 9 10 11 12 4 5 6 7 8 9 10 11 12 13 +12V Thermal Sensor STK404−140N−E Shutdown Signal 1 2 3 +12V Figure 25. STK404−000−Esr Thermal Shut Down Application http://onsemi.com 9 STK404−070NGEVB, STK404−120NGEVB, STK404−140NGEVB THERMAL SENSOR CHARACTERISTIC STK404−120N−E 100k Reference 7 7 5 5 3 3 2 2 10k 10k 7 7 Resistance, Rp (W) Resistance, Rp (W) 100k STK404−140N−E 5 3 2 1k 5 3 2 1k Max. 7 7 5 5 Typ. 3 2 100 −20 20 40 60 80 Max. Typ. 3 2 Min. 0 Reference 100 −20 100 120 140 160 Temperature, Tp (°C) Min. 0 20 40 60 80 100 120 140 160 Temperature, Tp (°C) Figure 26. Rp vs. Tp Figure 27. Rp vs. Tp http://onsemi.com 10 STK404−070NGEVB, STK404−120NGEVB, STK404−140NGEVB ROAD-SHORT & DC VOLTAGE PROTECTION APPLICATION + amp. − IN 1 NF SUB 2 3 4 5 6 7 8 +V O 10 9 6.8kΩ 56kΩ Road−Short Protection 0.22 Ω 56kΩ +5V 100kΩ 47μF 22kΩ 10kΩ 10k Ω 1kΩ 82kΩ 100k Ω 10μF 10kΩ to SB1 to SB2 H:Operation Mode L:Protection Mode −VCC DC Voltage Protection OUT Figure 28. STK404−070N−E Road-short & DC Voltage Protection Application + amp. − 1 IN NF SUB 2 3 4 5 6 7 8 9 −VE 10 11 Road−Short Protection +VE 12 6.8kW 56kW 0.22W 56kW +5V 100kW 47mF 10kW 22kW 10kW 1kW 82kW 100kW 10mF 10kW to SB1 to SB2 H:Operation Mode L:Protection Mode −VCC DC Voltage Protection OUT Figure 29. STK404−120N−E Road-short & DC Voltage Protection Application http://onsemi.com 11 STK404−070NGEVB, STK404−120NGEVB, STK404−140NGEVB + amp. − 1 2 IN NF SUB 3 4 5 6 7 8 9 10 −VE 11 12 Road−Short Protection +VE 13 6.8kW 56kW 0.22W 56kW +5V 100kW 47mF 10kW 22kW 10kW 1kW 82kW 100kW 10mF 10kW to SB1 to SB2 H:Operation Mode L:Protection Mode −VCC DC Voltage Protection OUT Figure 30. STK404−140N−E Road-short & DC Voltage Protection Application http://onsemi.com 12 onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. The evaluation board/kit (research and development board/kit) (hereinafter the “board”) is not a finished product and is not available for sale to consumers. The board is only intended for research, development, demonstration and evaluation purposes and will only be used in laboratory/development areas by persons with an engineering/technical training and familiar with the risks associated with handling electrical/mechanical components, systems and subsystems. This person assumes full responsibility/liability for proper and safe handling. Any other use, resale or redistribution for any other purpose is strictly prohibited. THE BOARD IS PROVIDED BY ONSEMI TO YOU “AS IS” AND WITHOUT ANY REPRESENTATIONS OR WARRANTIES WHATSOEVER. WITHOUT LIMITING THE FOREGOING, ONSEMI (AND ITS LICENSORS/SUPPLIERS) HEREBY DISCLAIMS ANY AND ALL REPRESENTATIONS AND WARRANTIES IN RELATION TO THE BOARD, ANY MODIFICATIONS, OR THIS AGREEMENT, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING WITHOUT LIMITATION ANY AND ALL REPRESENTATIONS AND WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, NON−INFRINGEMENT, AND THOSE ARISING FROM A COURSE OF DEALING, TRADE USAGE, TRADE CUSTOM OR TRADE PRACTICE. onsemi reserves the right to make changes without further notice to any board. You are responsible for determining whether the board will be suitable for your intended use or application or will achieve your intended results. Prior to using or distributing any systems that have been evaluated, designed or tested using the board, you agree to test and validate your design to confirm the functionality for your application. Any technical, applications or design information or advice, quality characterization, reliability data or other services provided by onsemi shall not constitute any representation or warranty by onsemi, and no additional obligations or liabilities shall arise from onsemi having provided such information or services. onsemi products including the boards are not designed, intended, or authorized for use in life support systems, or any FDA Class 3 medical devices or medical devices with a similar or equivalent classification in a foreign jurisdiction, or any devices intended for implantation in the human body. You agree to indemnify, defend and hold harmless onsemi, its directors, officers, employees, representatives, agents, subsidiaries, affiliates, distributors, and assigns, against any and all liabilities, losses, costs, damages, judgments, and expenses, arising out of any claim, demand, investigation, lawsuit, regulatory action or cause of action arising out of or associated with any unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of any products and/or the board. This evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and may not meet the technical requirements of these or other related directives. FCC WARNING – This evaluation board/kit is intended for use for engineering development, demonstration, or evaluation purposes only and is not considered by onsemi to be a finished end product fit for general consumer use. It may generate, use, or radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this equipment may cause interference with radio communications, in which case the user shall be responsible, at its expense, to take whatever measures may be required to correct this interference. onsemi does not convey any license under its patent rights nor the rights of others. LIMITATIONS OF LIABILITY: onsemi shall not be liable for any special, consequential, incidental, indirect or punitive damages, including, but not limited to the costs of requalification, delay, loss of profits or goodwill, arising out of or in connection with the board, even if onsemi is advised of the possibility of such damages. In no event shall onsemi’s aggregate liability from any obligation arising out of or in connection with the board, under any theory of liability, exceed the purchase price paid for the board, if any. The board is provided to you subject to the license and other terms per onsemi’s standard terms and conditions of sale. For more information and documentation, please visit www.onsemi.com. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com onsemi Website: www.onsemi.com ◊ TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 www.onsemi.com 1 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative