PS-M07D12S4-NJ5R-137S

DC-AC INVERTER UNIT PS-M07D12S4-NJ5R-137(S) (6,5 W DUAL OUTPUTS) DESCRIPTION : This low profile DC to AC Inverter is developed for dual lamps. Optimized for Chi Mei: G104X1-L01 (PRELIMINARY INFORMATION) APPLICABLE LCD: 6.4 to 12 inches double lamp type Lamp Voltage 460 Vrms Lamp Current 7 mArms Lamp Start Up Voltage 1.300 Vrms (Vin : 12 Vdc) FEATURES : Remote ON/OFF Ext. PWM-Dimming Function RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : 5 ± 0.5 -10°C ~ +55°C -20°C ~ +85°C 95 %RH max LxWxH 105 x 22,5 x 10mm 22,5 ± 0.5 15 ± 0.3 CN1 CN2 Unit : mm Weight :20 (g) typ. 10.0MAX Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 3 Part Description PCB Connector CN1 Connector CN2 Qty. 1 1 1 Material UL94V-0 (FR-4 or CEM-3) S5B-PH-SM3 SM03(4.0)B-BHS Output side CN2: Note t=1.6m m JST or equal JST or equal Input side CN1: Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 CN 1-5 Symbols Vin GND Ext. PWM N.C. Vrm t Ratings 12 Vdc 0 ~ 5 Vdc (L activ) 0 / 5 Vdc (H activ) Pin No. CN 2-1 CN 2-2 CN 2-3 Symbols VLOW VHIGH1 VHIGH2 Ratings 0Vdc 460Vrm s (7m Arm s ) 460Vrm s (7m Arm s ) Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page (1) Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Version 1.0, 1st June 2007 All specifications are subject to change without notice. DC-AC INVERTER UNIT PS-M07D12S4-NJ5R-137(S) (6,5 W DUAL OUTPUTS) ELECTRICAL CHARACTERISTICS : Conditions Vrmt (V) 5±0.25 5±0.25 5±0.25 5±0.25 5±0.25 Specification Min. Typ. Max. 6.5 7.0 7.0 0.7 50 1.300 7.5 8.0 1.2 55 - (PRELIMINARY INFORMATION) Parameters Output Current Output Current Input Current Frequency Open Circuit Voltage Symbols Iout Iout Iin F Vopen V in (V) 12±0.12 12±1.2 12±1.2 12±1.2 11,4 Tu (°C) -10 ~ +55 -10 -10 -10 -10 Unit m Arm s m Arm s Adc kHz Vrm s Note ~ +55 6.0 ~ +55 ~ +55 45 ~ +55 1.200 Note 1 : Note 2: Note 3: Please keep minimum of 2mm clearance (all directions) between inverter high voltage area as marked on mechanical drawing and any conductors. Remote ON/OFF (CN1-5) has priority and can not be used in combination with External PWM Dimming (CN1-3). When 'Ext.PWM' (CN1-3) is used 'Vrmt' (CN1-5) should not be connected. The external PWM frequency should be in a range of 100 ~ 500 Hz. For other frequency please request. The optimum is 250 Hz. Here you will normally not get a interference to the vertical sync. frequency. F F 1000:1 PROBE TEST CIRCUIT : Vin 12 V A Iin V CN1-1 SW3 CN2-3 Vopen V ~ SW 1 a b Operation of unit Operation Non operation CN1-2 T1 SW4 CN2-2 CN1-3 Ext. PWM* 0/5V RL2 A RL1 CL2 CL1 NC CN1-4 ~ Iout ~ Iout1 2 SW5 CN2-1 A Vrmt 2.5 Vdc ~ Vin a V b SW1 CN1-5 *) Only active when Vrmt is 0 Vdc or floating EXTERNAL PWM-DIMMING ( Remote ON / OFF Detailed Circuit Diagram ): Power Systems – The Power Solution Web: Email: www.Power-Systems.de Info@Power-Systems.de Page (2) Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Version 1.0, 1st June 2007 All specifications are subject to change without notice.