CM150DY-12H

CM150DY-12H Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Dual IGBTMOD™ H-Series Module 150 Amperes/600 Volts A B H E E H S C2E1 E2 C1 E2 G2 C K G1 E1 G S L R - M5 THD (3 TYP.) P - DIA. (2 TYP.) J J J .110 TAB N N M D F Q Description: Powerex IGBTMOD™ Modules are designed for use in switching applications. Each module consists of two IGBT Transistors in a half-bridge configuration with each transistor having a reverseconnected super-fast recovery free-wheel diode. All components and interconnects are isolated from the heat sinking baseplate, offering simplified system assembly and thermal management. G2 E2 C2E1 E2 C1 E1 G1 Features: □ Low Drive Power □ Low VCE(sat) □ Discrete Super-Fast Recovery (70ns) Free Wheel Diode □ High Frequency Operation (20-25kHz) □ Isolated Baseplate for Easy Heat Sinking Applications: □ AC Motor Control □ Motion/Servo Control □ UPS □ Welding Power Supplies □ Laser Power Supplies Ordering Information: Example: Select the complete part module number you desire from the table below -i.e. CM150DY-12H is a 600V (VCES), 150 Ampere Dual IGBTMOD™ Power Module. Type CM Current Rating Amperes 150 VCES Volts (x 50) 12 Outline Drawing and Circuit Diagram Dimensions A B C D E F G H J Inches 3.70 3.150± 0.01 1.89 1.18 Max. 0.90 0.83 0.71 0.67 0.63 Millimeters 94.0 80.0± 0.25 48.0 30.0 Max. 23.0 21.2 18.0 17.0 16.0 Dimensions K L M N P Q R S Inches 0.51 0.47 0.30 0.28 0.256 Dia. 0.26 M5 Metric 0.16 Millimeters 13.0 12.0 7.5 7.0 Dia. 6.5 6.5 M5 4.0 237 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CM150DY-12H Dual IGBTMOD™ H-Series Module 150 Amperes/600 Volts Absolute Maximum Ratings, Tj = 25 °C unless otherwise specified Ratings Junction Temperature Storage Temperature Collector-Emitter Voltage (G-E SHORT) Gate-Emitter Voltage Collector Current Peak Collector Current Diode Forward Current Diode Forward Surge Current Power Dissipation Max. Mounting Torque M5 Terminal Screws Max. Mounting Torque M6 Mounting Screws Module Weight (Typical) V Isolation * Pulse width and repetition rate should be such that device junction temperature does not exceed the device rating. Symbol Tj Tstg VCES VGES IC ICM IF IFM Pd – – – VRMS CM150DY-12H –40 to 150 –40 to 125 600 ± 20 150 300* 150 300* 600 17 26 270 2500 Units °C °C Volts Volts Amperes Amperes Amperes Amperes Watts in-lb in-lb Grams Volts Static Electrical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Collector-Cutoff Current Gate Leakage Current Gate-Emitter Threshold Voltage Collector-Emitter Saturation Voltage Symbol ICES IGES VGE(th) VCE(sat) QG VFM Test Conditions VCE = VCES, VGE = 0V VGE = VGES, VCE = 0V IC = 15mA, VCE = 10V IC = 150A, VGE = 15V IC = 150A, VGE = 15V, Tj = 150°C Total Gate Charge Diode Forward Voltage VCC = 300V, IC = 150A, VGS = 15V IE = 150A, VGS = 0V Min. – – 4.5 – – – – Typ. – – 6.0 2.1 2.15 450 – Max. 1.0 0.5 7.5 2.8** – – 2.8 Units mA µA Volts Volts Volts nC Volts ** Pulse width and repetition rate should be such that device junction temperature rise is negligible. Dynamic Electrical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Input Capacitance Output Capacitance Reverse Transfer Capacitance Resistive Load Switching Times Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Symbol Cies Coes Cres td(on) tr td(off) tf trr Qrr IE = 150A, diE/dt = –300A/µs IE = 150A, diE/dt = –300A/µs VCC = 300V, IC = 150A, VGE1 = VGE2 = 15V, RG = 4.2Ω VGE = 0V, VCE = 10V, k = 1MHz Test Conditions Min. – – – – – – – – – Typ. – – – – – – – – 0.41 Max. 15 5.3 3 200 550 300 300 110 – Units nF nF nF ns ns ns ns ns Diode Reverse Recovery Time Diode Reverse Recovery Charge µC Thermal and Mechanical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Thermal Resistance, Junction to Case Thermal Resistance, Junction to Case Contact Thermal Resistance Symbol Rth(j-c) Rth(j-c) Rth(c-f) Test Conditions Per IGBT Per FWDi Per Module, Thermal Grease Applied Min. – – – Typ. – – – Max. 0.21 0.47 0.065 Units °C/W °C/W °C/W 238 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CM150DY-12H Dual IGBTMOD™ H-Series Module 150 Amperes/600 Volts OUTPUT CHARACTERISTICS (TYPICAL) TRANSFER CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) 300 COLLECTOR CURRENT, IC, (AMPERES) COLLECTOR CURRENT, IC, (AMPERES) 300 250 200 150 100 50 0 0 2 4 6 8 10 0 4 8 12 16 20 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) GATE-EMITTER VOLTAGE, VGE, (VOLTS) COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) 5 VCE = 10V Tj = 25°C Tj = 125°C VGE = 15V Tj = 25°C Tj = 125°C Tj = 25oC 250 200 150 VGE = 20V 15 12 4 11 3 10 2 100 9 50 0 1 7 8 0 0 100 200 300 COLLECTOR-CURRENT, IC, (AMPERES) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) CAPACITANCE VS. VCE (TYPICAL) 10 COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) 103 Tj = 25°C Tj = 25°C IC = 300A EMITTER CURRENT, IE, (AMPERES) CAPACITANCE, Cies, Coes, Cres, (nF) 102 8 101 Cies 6 IC = 150A 102 Coes 4 100 2 IC = 60A VGE = 0V f = 1MHz Cres 0 0 4 8 12 16 20 GATE-EMITTER VOLTAGE, VGE, (VOLTS) 101 0 0.8 1.6 2.4 3.2 4.0 EMITTER-COLLECTOR VOLTAGE, VEC, (VOLTS) 10-1 10-1 100 101 102 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) HALF-BRIDGE SWITCHING CHARACTERISTICS (TYPICAL) REVERSE RECOVERY CHARACTERISTICS (TYPICAL) REVERSE RECOVERY CURRENT, Irr, (AMPERES) GATE CHARGE, VGE 103 REVERSE RECOVERY TIME, t rr, (ns) 103 102 20 GATE-EMITTER VOLTAGE, VGE, (VOLTS) tf SWITCHING TIME, (ns) 16 VCC = 200V td(off) td(on) 102 tr 102 Irr t rr 12 101 VCC = 300V 8 VCC = 300V VGE = ±15V RG = 4.2Ω Tj = 125°C di/dt = -300A/µsec Tj = 125°C 4 101 101 102 COLLECTOR CURRENT, IC, (AMPERES) 103 101 101 102 EMITTER CURRENT, IE, (AMPERES) 100 103 0 0 100 200 300 400 500 600 GATE CHARGE, QG, (nC) 239 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CM150DY-12H Dual IGBTMOD™ H-Series Module 150 Amperes/600 Volts NORMALIZED TRANSIENT THERMAL IMPEDANCE, Z th(j-c) Zth = Rth • (NORMALIZED VALUE) 100 Single Pulse TC = 25°C Per Unit Base = R th(j-c) = 0.21°C/W NORMALIZED TRANSIENT THERMAL IMPEDANCE, Z th(j-c) Zth = Rth • (NORMALIZED VALUE) 10-3 101 TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT) 10-2 10-1 100 101 10-3 101 TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi) 10-2 10-1 100 101 100 Single Pulse TC = 25°C Per Unit Base = R th(j-c) = 0.47°C/W 10-1 10-1 10-1 10-1 10-2 10-2 10-2 10-2 10-3 10-5 TIME, (s) 10-4 10-3 10-3 10-3 10-5 TIME, (s) 10-4 10-3 10-3 240