ICS525R-04LF

DATASHEET ICS525-04 OSCAR™ USER CONFIGURABLE PECL CLOCK Description Features The ICS525-04 OSCaRTM is the most flexible way to generate a high quality, high frequency differential PECL clock output from a crystal or CMOS clock input. The name OSCaRTM stands for Oscillator Replacement, as it is designed to replace crystal oscillators in almost any electronic system. Users can easily configure the device to produce nearly any output frequency from any input frequency by grounding or floating the select pins. Neither microcontroller, software, nor device programmer are needed to set the frequency. Using Phase Locked Loop techniques, the device accepts a crystal or clock to produce output clocks up to 156 MHz at 3.3V, keeping them frequency locked together. • Packaged as 28 pin SSOP (150 mil body) • Highly accurate frequency generation • User determines the output frequency by setting all • • • • • • • • • • • • • internal dividers Eliminates need for custom oscillators No software needed Pull-ups on select inputs Input crystal frequency of 5 - 27 MHz Input clock frequency of 2 - 50 MHz Output clock frequencies up to 156 MHz at 3.3V Output clock frequencies up to 200 MHz at 5V Very low jitter PECL levels set by external resistors Operating voltage of 3.3V or 5V Ideal for oscillator replacement Industrial temperature version available Advanced, low power CMOS process 2 VDD For simple multipliers to produce common frequencies, refer to the LOCOTM family of parts, which are smaller and more cost effective. This product is intended for clock generation. It has low output jitter (variation in the output period), but input to output skew and jitter are not defined nor guaranteed. For applications which require defined input to output timing, use the ICS527-02. Block Diagram 560Ω VDD 82Ω X1/ICLK Crystal or clock input VDD RES Crystal Oscillator Reference Divider PECL Phase Comparator, Charge Pump, and Loop Filter VCO 820Ω Output Divider X2 VCO Divider Optional crystal capacitors GND VDD 82Ω PECL 820Ω 7 R6:R0 IDT™ / ICS™ OSCAR™ USER CONFIGURABLE PECL CLOCK 9 V8:V0 1 2 GND 3 S2:S0 GND ICS525-04 REV E 051310 ICS525-04 OSCAR™ USER CONFIGURABLE PECL CLOCK PECL MULTIPLIER Pin Assignment R5 1 28 R4 R6 2 27 R3 S0 3 26 R2 S1 4 25 R1 S2 5 24 R0 VDD 6 23 VDD X1/ICLK 7 22 PECL X2 8 21 PECL GND 9 20 GND V0 10 19 RES V1 11 18 V8 V2 12 17 V7 V3 13 16 V6 V4 14 15 V5 28 pin 150 mil body SSOP Maximum Output Frequency and Output Divider Table S2 S1 S0 CLK Output Pin 5 Pin 4 Pin 3 Divider Max Output Frequency (MHz) VDD = 5V VDD = 3.3V 0 - 70 ° C -40 - 85 ° C 0 - 70 ° C -40 - 85 ° C 0 0 0 6 45 44 27 26 0 0 1 2 120 117 81 77 0 1 0 8 34 33 20 19 0 1 1 4 68 66 40 38 1 0 0 5 54 53 32 31 1 0 1 7 39 38 23 22 1 1 0 1 200 195 162 154 1 1 1 3 90 89 54 51 IDT™ / ICS™ OSCAR™ USER CONFIGURABLE PECL CLOCK 2 ICS525-04 REV E 051310 ICS525-04 OSCAR™ USER CONFIGURABLE PECL CLOCK PECL MULTIPLIER Pin Descriptions Pin Number Pin Name Pin Type 1 R5 Input Reference divider word input pins determined by user. Forms a binary number from 0 to 127. Internal pull-up. 2 R6 Input Reference divider word input pins determined by user. Forms a binary number from 0 to 127. Internal pull-up. 3 S0 Input Select pins for output divider determined by user. See table above. Internal pull-up. 4 S1 Input Select pins for output divider determined by user. See table above. Internal pull-up. 5 S2 Input Select pins for output divider determined by user. See table above. Internal pull-up. 6 VDD Power Connect to VDD. 7 X1/ICLK Input Crystal connection. Connect to a parallel resonant crystal or input clock. 8 X2 Input Crystal connection. Connect to a crystal or leave unconnected for clock. 9 GND Power Connect to ground. 10 - 18 V0 - V8 Input VCO divider word input pins determined by user. Forms a binary number from 0 to 511. Internal pull-up. 19 RES Input Bias resistor input. Connect a resistor between this pin and VDD. 20 GND Power Connect to ground. 21 PECL Output Complementary PECL output. Connect resistor load to this pin. 22 PECL Output PECL output. Connect resistor load to this pin. 23 VDD Power Connect to VDD. 24 R0 Input Reference divider word input pins determined by user. Forms a binary number from 0 to 127. Internal pull-up. 25 R1 Input Reference divider word input pins determined by user. Forms a binary number from 0 to 127. Internal pull-up. 26 R2 Input Reference divider word input pins determined by user. Forms a binary number from 0 to 127. Internal pull-up. 27 R3 Input Reference divider word input pins determined by user. Forms a binary number from 0 to 127. Internal pull-up. 28 R4 Input Reference divider word input pins determined by user. Forms a binary number from 0 to 127. Internal pull-up. Pin Description IDT™ / ICS™ OSCAR™ USER CONFIGURABLE PECL CLOCK 3 ICS525-04 REV E 051310 ICS525-04 OSCAR™ USER CONFIGURABLE PECL CLOCK PECL MULTIPLIER External Components The output of the ICS525-04 can be determined by the following simple equation: Decoupling Capacitors VDW + 8 PECL Frequency = Input Frequency × --------------------------------------------( RDW + 2 ) • OD As with any high performance mixed-signal IC, the ICS525-04 must be isolated from system power supply noise to perform optimally. Where: Decoupling capacitors of 0.01µF must be connected between each VDD and the GND, one on each side of the chip.The capacitor must be connected close to the device to minimize lead inductance. No external power supply filtering is required for this device. Reference Divider Word (RDW) = 0 to 127 VCO Divider Word (VDW) = 0 to 511 Output Divider (OD) = values on page 2 External Resistors Also, the following operating ranges should be observed: A 560Ω resistor must be connected between RES (pin 19) and VDD. A total of four resistors are needed for the PECL outputs as shown on the block diagram on page 1. The value of these resistors are shown, but can be varied to change the differential pair output swing and the common mode voltage. Consult application note MAN09 for more information. VDW + 8 10M < Input Frequency x ----------------------------- < 200M ( 5V )or162M ( 3.3v ) ) ( RDW + 2 ) InputFrequency 200kHz < ----------------------------------------------( RDW + 2 ) Crystal Load Capacitors The total on-chip capacitance for a crystal is approximately 16 pF, so a parallel resonant, fundamental mode crystal with this value of load (correlation) capacitance should be used. For crystals with a specified load capacitance greater than 16 pF, crystal capacitors may be connected from each of the pins X1 and X2 to Ground as shown in the block diagram. The value (in pF) of these crystal caps should be (CL 16)*2, where CL is the crystal load capacitance. These external capacitors are only required for applications where the exact frequency is critical. For a clock input, connect to X1 and leave X2 unconnected (no capacitors on either). See table on page 2 for full details of maximum output. The dividers are expressed as integers. For example, if a 66.66 MHz output on CLK1 is desired from a 14.31818 MHz input, the VCO divider word (VDW) should be 276, with an output divide (OD) of 2. In this example, R6:R0 is 0111011, V8:V0 is 100010100 and S2:S0 is 001. Since all of these inputs have pull-up resistors, it is only necessary to ground the zero pins, namely V7, V6, V5, V3, V1, V0, R6, R2, S2, and S1. Determining the Output Frequency To determine the best combination of VCO, reference, and output divide, use the ICS525 Calculator on our web site: www.idt.com. The online form is easy to use and quickly shows you up to three options for these settings. Users have full control in setting the desired output frequency over the range shown in the table on page 2. To replace a standard oscillator, users should connect the divider select input pins directly to ground (or VDD, although this is not required because of internal pull-ups) during Printed Circuit Board layout. The ICS525-04 will automatically produce the correct clock when all components are soldered. It is also possible to connect the inputs to parallel I/O ports to switch frequencies. By choosing divides carefully, the number of inputs which need to be changed can be minimized. Observe the restrictions on allowed values of VDW and RDW. IDT™ / ICS™ OSCAR™ USER CONFIGURABLE PECL CLOCK 4 ICS525-04 REV E 051310 ICS525-04 OSCAR™ USER CONFIGURABLE PECL CLOCK PECL MULTIPLIER Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS525-04. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5V to VDD+0.5V Ambient Operating Temperature -40 to +85° C Storage Temperature -65 to +150° C Junction Temperature 175° C Soldering Temperature 260° C Recommended Operation Conditions Parameter Min. Typ. Max. Units Ambient Operating Temperature, ICS525R-04 0 +70 °C Ambient Operating Temperature, ICS525R-04I -40 +85 °C Power Supply Voltage (measured in respect to GND) +3.0 +5.5 V DC Electrical Characteristics Unless stated otherwise, VDD = 3.3V ±10%, Ambient Temperature 0 to +70° C Parameter Symbol Operating Voltage VDD Supply Current IDD Conditions Min. Typ. 3.0 Max. Units 5.5 V 15 MHz in, 60MHz out, no load 34 mA 15MHz in, 60MHz out, VDD = 5V 60 mA Input High Voltage VIH Input Low Voltage VIL Input High Voltage VIH X1/ICLK only Input Low Voltage VIL X1/ICLK only Output High Voltage VOH IOH = -12 mA Output Low Voltage VOL IOL = 12 mA Input Capacitance CIN V, R, S select pins 5 pF On-chip pull-up resistor RPU V, R, S select pins 270 kΩ 2 V 0.8 IDT™ / ICS™ OSCAR™ USER CONFIGURABLE PECL CLOCK 5 VDD/2+1 VDD/2 VDD/2 V V VDD/2-1 2.4 V V 0.4 ICS525-04 V REV E 051310 ICS525-04 OSCAR™ USER CONFIGURABLE PECL CLOCK PECL MULTIPLIER AC Electrical Characteristics Unless stated otherwise, VDD = 3.3V ±5%, Ambient Temperature -40 to +85° C Parameter Input Frequency Symbol FIN Output Frequency with OD=2, VDD=4.5 to 5 FOUT Output Frequency with OD=2, VDD=3.0 to 3.3 FOUT Absolute Clock Period Jitter tja One sigma Clock Period Jitter tjs IDT™ / ICS™ OSCAR™ USER CONFIGURABLE PECL CLOCK Conditions Min. Typ. Max. Units Crystal input 5 27 MHz Clock input 2 50 MHz 0 to +70° C 1 120 MHz -40 to +85° C 1 117 MHz 0 to +70° C 1 81 MHz -40 to +85° C 1 77 MHz Deviation from mean 6 ± 50 ps 20 ps ICS525-04 REV E 051310 ICS525-04 OSCAR™ USER CONFIGURABLE PECL CLOCK PECL MULTIPLIER Package Outline and Package Dimensions (28 pin SSOP, 150 mil Body, 0.025 mm Pitch) Package dimensions are kept current with JEDEC Publication No. 95, MO-153 Millimeters 28 Symbol E1 A A1 A2 b C D E E1 e L α aaa E INDEX AREA 1 2 D A 2 Min Inches Max 1.35 1.75 0.10 0.25 -1.50 0.20 0.30 0.18 0.25 9.80 10.00 5.80 6.20 3.80 4.00 0.635 Basic 0.40 1.27 0° 8° -0.10 Min Max .053 .069 .0040 .010 -.059 .008 .012 .007 .010 .386 .394 .228 .244 .150 .157 0.025 Basic .016 .050 0° 8° -0.004 A A 1 c -Ce SEATING PLANE b L aaa C Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature 525R-04LF ICS525R-04LF Tubes 28-pin SSOP 0 to +70° C 525R-04LFT ICS525R-04LF Tape and Reel 28-pin SSOP 0 to +70° C 525R-04ILF ICS525R-04ILF Tubes 28-pin SSOP -40 to +85° C 525R-04ILFT ICS525R-04ILF Tape and Reel 28-pin SSOP -40 to +85° C "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT™ / ICS™ OSCAR™ USER CONFIGURABLE PECL CLOCK 7 ICS525-04 REV E 051310 ICS525-04 OSCAR™ USER CONFIGURABLE PECL CLOCK PECL MULTIPLIER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 www.idt.com/go/clockhelp Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. © 2020 Renesas Electronics Corporation. All rights reserved.