ICS527R-02

DATASHEET CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER ICS527-02 Description Features The ICS527-02 Clock Slicer is the most flexible way to generate a CMOS output clock from a PECL input clock with zero skew. The user can easily configure the device to produce nearly any output clock that is multiplied or divided from the input clock. The part supports non-integer multiplications and divisions. A SYNC pulse indicates when the rising clock edges are aligned with zero skew. Using Phase-Locked Loop (PLL) techniques, the device accepts an input clock up to 200 MHz and produces an output clock up to 160 MHz. • • • • • • Packaged as 28-pin SSOP (150 mil body) Synchronizes fractional clocks rising edges PECL IN to CMOS OUT Pin selectable dividers Zero input to output skew User determines the output frequency—no software needed Slices frequency or period Input clock frequency of 1.5 MHz to 200 MHz Output clock frequencies from 4 MHz to 160 MHz Very low jitter Duty cycle of 45/55 Operating voltage of 3.3 V Advanced, low-power CMOS process Industrial temperature version available For a PECL input and output clock with zero delay, use the ICS527-04. • • • • • • • • For a CMOS input and PECL output with zero delay, use the ICS527-03. NOTE: EOL for non-green parts to occur on 5/13/10 per PDN U-09-01 The ICS527-02 aligns rising edges on PECLIN with FBIN at a ratio determined by the reference and feedback dividers. Block Diagram R6:R0 7 PECLIN 2 VDD Reference Divider PECLIN 33 ohm Phase Comparator, Charge Pump, and Loop Filter FBIN Feedback Divider 7 F6:F0 VCO Output Divider Divide by 2 SYNC 2 GND PDTS CLK1 2 S1:S0 IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER 1 1 0 33 ohm CLK2 Feedback can come from CLK1 or CLK2 (not both) DIV2 ICS527-02 REV H 092209 ICS527-02 CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER Pin Assignment PECL ZDB AND MULTIPLIER/DIVIDER Output Frequency Range Table R5 1 28 R4 R6 2 27 R3 D IV 2 3 26 R2 S0 4 25 R1 0 S1 5 24 R0 VDD 6 23 VDD P E C L IN 7 22 P E C L IN 8 21 GND S1 S0 Output Frequency (MHz) Commercial Industrial 0 10 - 50 16 - 45 0 1 5 - 40 8 - 33 C LK1 1 0 4 - 10 4-8 C LK2 1 1 20 -160 32 - 140 9 20 GND O ECLK2 10 19 PDTS F0 11 18 F B IN F1 12 17 F6 F2 13 16 F5 OECLK2 DIV2 CLK2 F3 14 15 F4 0 X Z 1 0 SYNC 1 1 CLK1/2 CLK2 Operation Table 28-pin 150 mil body SSOP Pin Descriptions Pin Number Pin Name Pin Type 1,2, 24-28 R5, R6, R0-R4 Input Reference divider word input pins determined by user. Forms a binary number from 0 to 127. Internal pull-up. 3 DIV2 Input Selects CLK2 function to output a SYNC signal or a divide by 2 of CLK1 based on the table above. Internal pull-up. 4, 5 S0, S1 Input Select pins for output divider determined by user. See table above. Internal pull-up. 6, 23 VDD Power Connect to +3.3 V. 7 PECLIN Input True PECL input clock. 8 PECLIN Input Complementary PECL input clock. 9, 20 GND Power Connect to ground 10 OECLK2 Input CLK2 Output Enable. CLK2 tri-stated when low. Internal pull-up. 11-17 F0-F6 Input Feedback divider word input pins determined by user. Forms a binary number from 0 to 127. Internal pull-up 18 FBIN Input Feedback clock input 19 PDTS Input Power Down. Active low. Turns off entire chip when low, both clock outputs are tri-stated. Internal pull-up. 21 CLK2 Output Output clock 2. Can be SYNC pulse or a low skew divide by 2 of CLK1. 22 CLK1 Output Output clock 1. Pin Description IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER 2 ICS527-02 REV H 092209 ICS527-02 CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER PECL ZDB AND MULTIPLIER/DIVIDER External Components Decoupling Capacitors As with any high performance mixed-signal IC, the ICS527-02 must be isolated from system power supply noise to perform optimally. Decoupling capacitors of 0.01µF must be connected between each VDD and the PCB ground plane. The capacitor must be connected close to the device to minimize lead inductance. Series Termination Resistor Clock output traces over one inch should use series termination. To series terminate a 50Ω trace (a commonly used trace impedance), place a 33Ω resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20Ω. P E C L IN P E C L IN C LK1 C LK2 p h a s e is in d e t e r m in a te C LK 1 F eedback P E C L IN P E C L IN C LK1 C LK2 C LK 2 Feedback Using the ICS527-02 Clock Slicer First use DIV2 to select the function of the CLK2 output. If DIV2 is high, a divide by 2, low skew version of CLK1 is present on CLK2. If DIV2 is low, a SYNC pulse is generated on CLK2. The SYNC pulse goes high synchronously with the rising edges of PECLIN and CLK1 that are de-skewed. The SYNC function operates at CLK1 frequencies up to 66 MHz. If neither CLK1/2 or a SYNC pulse are required, then CLK2 should be disabled by connecting OECLK2 to ground. This will also give the lowest jitter on CLK1. Next, the feedback scheme should be chosen. If CLK2 is being used as a SYNC pulse, or is tri-stated, then CLK1 must be connected to FBIN. If CLK2 is selected to be CLK1/2 (DIV2=1, OECLK2=1) then either CLK1 or CLK2 must be connected to FBIN. The choice between CLK1 or CLK2 is illustrated by the following examples where the device has been configured to generate CLK1 that is twice the frequency on PECLIN. Using CLK1 as feedback will always result in synchronized rising edges between PECLIN and CLK1 if CLK1 is used as feedback. CLK2 could be a falling edge compared to PECLIN. Therefore, wherever possible it is recommended to use CLK2 for feedback, which will synchronize the rising edges of all three clocks. More complicated feedback schemes can be used, such as incorporating multiple output buffers in the feedback path. An example is given later in the datasheet. The fundamental property of the ICS527-02 is that it aligns rising edges on PECLIN and FBIN at a ratio determined by the reference and feedback dividers. Set S1 and S0 (page 2) based on the output frequency. Lastly, the divider settings should be selected. This is described in the following section. Determining ICS527-02 Divider Settings The user has full control in setting the desired output clock over the range shown in the table on page 2. The user should connect the divider select input pins directly to ground (or VDD, although this is not required IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER 3 ICS527-02 REV H 092209 ICS527-02 CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER because of internal pull-ups) during Printed Circuit Board layout, so the ICS527-02 automatically produces the correct clock when mounted on the board. It is also possible to connect the inputs to parallel I/O ports in order to switch frequencies. The output of the ICS527-02 can be determined by the following simple equation: FDW + 2 FB Frequency = Input Frequency × ------------------------ RDW + 2 Where: Reference Divider Word (RDW) = 0 to 127 Feedback Divider Word (FDW) = 0 to 127 FB Frequency is the same as either CLK1 or CLK2 depending on feedback connection Also, the following operating ranges should be observed: PECL ZDB AND MULTIPLIER/DIVIDER S0 and S1 should be selected depending on the frequency of CLK1. The table on page 2 gives the ranges. The dividers are expressed as integers. For example, if a 50 MHz output on CLK1 is desired from a 40 MHz input, the reference divider word (RDW) should be 2 and the feedback divider word (FDW) should be 3 which gives the required 5/4 multiplication. If multiple choices of dividers are available, then the lowest numbers should be used. In this example, the output divide (OD) should be selected to be 2. Then R6:R0 is 0000010, F6:F0 is 0000011 and S1:S0 is 00. Also, this example assumes CLK1 is connected to FBIN. If you need assistance determining the optimum divider settings, please send an e-mail to mk-support@icst.com with the desired input clock and the desired output frequency. Input Frequency 300kHz < ------------------------------------------- < 20 MHz RDW + 2 Typical Example The layout diagram below will produce the waveforms shown on the right. VDD 0.01µF R5 R4 R6 R3 DIV2 R2 S0 R1 S1 R0 VDD 0.01µF 40 MHz PECLIN VDD 40 MHz PECLIN CLK1 40 MHz PECLIN CLK2 33Ω GND OECLK2 PDTS F0 FBIN F1 F6 F2 F5 F3 F4 PECLIN SYNC 33Ω GND 50 MHz 50 MHz CLK1 SYNC CLK2 Note: The series termination resistor is located before the feedback trace. IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER 4 ICS527-02 REV H 092209 ICS527-02 CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER PECL ZDB AND MULTIPLIER/DIVIDER Multiple Output Example In this example, an input clock of 125 MHz is used. Eight copies of 50 MHz are required as are eight copies of 25 MHz, de-skewed and aligned to the 125 MHz input clock. The following solution uses the MK74CB217 which has dual 1 to 8 buffers with low pin-to-pin skew. VDD INA INB R6 R3 QA0 QB0 DIV2 R2 QA1 QB1 S0 R1 QA2 QB2 S1 R0 VDD VDD VDD 125 MHz PECLIN 125 MHz PECLIN 0.01µF VDD VDD CLK1 50M CLK2 25M 0.01µF QA3 QA4 MK74CB217 R4 ICS527-02 0.01µF R5 VDD 0.01µF QB3 QB4 GND GND GND GND OECLK2 PDTS GND GND F0 FBIN QA5 QB5 F1 F6 QA6 QB6 F2 F5 QA7 QB7 F3 F4 OEA OEB The layout design above produces the waveforms shown below. Note: Series terminating resistors are not shown. 125 M H z, PEC LIN 25 M H z, Q A0-7 50 M H z, Q B0-7 P EC LIN not show n PCB Layout Recommendations For optimum device performance and lowest output phase noise, the following guidelines should be observed. 1) Each 0.01µF decoupling capacitor should be mounted on the component side of the board as close to the VDD pin as possible. No via’s should be used between decoupling capacitor and VDD pin. The PCB trace to VDD pin should be kept as short as possible, as should the PCB trace to the ground via. 3) An optimum layout is one with all components on the same side of the board, minimizing vias through other signal layers. Other signal traces should be routed away from the ICS527-02. This includes signal traces just underneath the device, or on layers adjacent to the ground plane layer used by the device. 2) To minimize EMI the 33Ω series termination resistor, if needed, should be placed close to the clock outputs. IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER 5 ICS527-02 REV H 092209 ICS527-02 CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER PECL ZDB AND MULTIPLIER/DIVIDER Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS527-02. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature -40 to +85° C Storage Temperature -65 to +150° C Junction Temperature 125° C Soldering Temperature 260° C Recommended Operation Conditions Parameter Min. Typ. Max. Units Ambient Operating Temperature, ICS527R-02 0 – +70 °C Ambient Operating Temperature, ICS527R-02I -40 – +85 °C +3.135 +3.3 +3.465 V Power Supply Voltage (measured in respect to GND) DC Electrical Characteristics Unless stated otherwise, VDD = 3.3V ±5%, Ambient Temperature 0 to +70° C Parameter Symbol Operating Voltage VDD Supply Current IDD Supply Current, Power Down IDDPD Input High Voltage VIH Input Low Voltage VIL Conditions Min. Typ. Max. Units 3.135 3.3 3.465 V 15 MHz in, 60 MHz out, no load 18 mA PDTS=0 20 µA 2 V 0.8 V Input Voltage, peak-to-peak PECLIN, PECLIN 0.3 1 V Common Mode Range PECLIN, PECLIN VDD-1.4 VDD-0.6 V Output High Voltage VOH IOH = -12 mA Output Low Voltage VOL IOL = 12 mA IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER 6 2.4 V 0.4 ICS527-02 V REV H 092209 ICS527-02 CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER Parameter Symbol Conditions Input Capacitance CIN Except PECLIN and FBIN Short Circuit Current On-chip pull-up resistor PECL ZDB AND MULTIPLIER/DIVIDER Min. Typ. Max. Units 5 pF IOS ±70 mA RPU 270 kΩ AC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V ±5%, Ambient Temperature -40 to +85° C Parameter Input Frequency Output Frequency, CLK1 Symbol Conditions Max. Units 1.5 200 MHz 0 to +70° C 4 160 MHz -40 to +85° C 4 140 MHz FIN FOUT Min. Typ. Output Rise Time tOR 0.8 to 2.0 V, CL=15 pF 1 ns Output Fall Time tOF 2.0 to 0.8 V, CL=15 pF 1 ns Output Duty Cycle (% high time) tOD Measured at VDD/2, CL=15 pF 55 % Power Down Time, PDTS low to clocks tri-stated 50 ns Power Up Time, PDTS high to clocks stable 10 ms Absolute Clock Period Jitter tja One sigma Clock Period Jitter tjs Input to output skew tIO PECLIN to CLK1, Note 1 Device to device skew tpi Common PECLIN, measured at FBIN 45 Deviation from mean 50 ± 90 ps 40 ps -250 0 250 ps 500 ps Note 1: Assumes clocks with same rise time, measured from rising edges at VDD/2. IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER 7 ICS527-02 REV H 092209 ICS527-02 CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER PECL ZDB AND MULTIPLIER/DIVIDER Package Outline and Package Dimensions (28-pin SSOP, .150 mil Body, 0.025 mm Pitch) Package dimensions are kept current with JEDEC Publication No. 95, MO-153 Millimeters 28 Symbol E1 A A1 A2 b C D E E1 e L α aaa E INDEX AREA 1 2 D A 2 Min Inches Max 1.35 1.75 0.10 0.25 -1.50 0.20 0.30 0.18 0.25 9.80 10.00 5.80 6.20 3.80 4.00 0.635 Basic 0.40 1.27 0° 8° -0.10 Min Max .053 .069 .0040 .010 -.059 .008 .012 .007 .010 .386 .394 .228 .244 .150 .157 0.025 Basic .016 .050 0° 8° -0.004 A A 1 c -Ce b SEATING PLANE L aaa C IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER 8 ICS527-02 REV H 092209 ICS527-02 CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER PECL ZDB AND MULTIPLIER/DIVIDER Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature 527R-02* ICS527R-02 Tubes 28-pin SSOP 0 to +70° C 527R-02T* ICS527R-02 Tape and Reel 28-pin SSOP 0 to +70° C 527R-02I* ICS527R-02I Tubes 28-pin SSOP -40 to +85° C 527R-02IT* ICS527R-02I Tape and Reel 28-pin SSOP -40 to +85° C 527R-02LF 527R02LF Tubes 28-pin SSOP 0 to +70° C 527R-02LFT 527R02LF Tape and Reel 28-pin SSOP 0 to +70° C 527R-02ILF 527R02ILF Tubes 28-pin SSOP -40 to +85° C 527R-02ILFT 527R02ILF Tape and Reel 28-pin SSOP -40 to +85° C *NOTE: EOL for non-green parts to occur on 5/13/10 per PDN U-09-01 While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT™ / ICS™ CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER 9 ICS527-02 REV H 092209 ICS527-02 CLOCK SLICER USER CONFIGURABLE PECL INPUT ZERO DELAY BUFFER PECL ZDB AND MULTIPLIER/DIVIDER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 www.idt.com/go/clockhelp Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA