ISL22429UFU10Z-TK

DATASHEET OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT ISL22426 ISL22429 FN6332 Rev 2.00 May 28, 2009 Dual Digitally Controlled Potentiometer (XDCP™) Low Noise, Low Power, SPI® Bus, 128 Taps, Wiper Only The ISL22429 integrates two digitally controlled potentiometers (DCP) and non-volatile memory on a monolithic CMOS integrated circuit. Features • Two potentiometers in one package The digitally controlled potentiometers are implemented with a combination of resistor elements and CMOS switches. The position of the wipers are controlled by the user through the SPI serial interface. Each potentiometer has an associated volatile Wiper Register (WR) and a non-volatile Initial Value Register (IVR) that can be directly written to and read by the user. The contents of the WR controls the position of the wiper. At power-up the device recalls the contents of the DCP’s IVR to the corresponding WR. The DCP can be used as a voltage divider in a wide variety of applications including control, parameter adjustments, AC measurement and signal processing. Pinout • 128 resistor taps • SPI serial interface • Non-volatile storage of wiper position • Wiper resistance: 70 typical @ 3.3V • Shutdown mode • Shutdown current 5µA max • Power supply: 2.7V to 5.5V • 50kor 10k total resistance • High reliability - Endurance: 1,000,000 data changes per bit per register - Register data retention: 50 years @ T < +55°C ISL22429 (10 LD MSOP) TOP VIEW • 10 Lead MSOP • Pb-free (RoHS compliant) NC 1 10 RW0 SCK 2 9 SHDN SDO 3 8 VCC GND 4 7 SDI RW1 5 6 CS Ordering Information PART NUMBER (Note) PART MARKING RESISTANCE OPTION (k) TEMP. RANGE (°C) PACKAGE (Pb-free) PKG. DWG. # ISL22429UFU10Z* 429UZ 50 -40 to +125 10 Ld MSOP M10.118 ISL22429WFU10Z* 429WZ 10 -40 to +125 10 Ld MSOP M10.118 *Add “-T” or “-TK” suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. FN6332 Rev 2.00 May 28, 2009 Page 1 of 13 ISL22429 Block Diagram VCC VCC SCK SDI SDO SPI INTERFACE CS POWER-UP INTERFACE, CONTROL AND STATUS LOGIC WR1 RW1 VCC NONVOLATILE REGISTERS SHDN WR0 RW0 GND Pin Descriptions MSOP PIN SYMBOL 1 NC 2 SCK SPI interface clock input 3 SDO Open drain SPI interface data output 4 GND Device ground pin 5 RW1 “Wiper” terminal of DCP1 6 CS Chip Select active low input 7 SDI SPI interface data input 8 VCC Power supply pin 9 SHDN Shutdown active low input 10 RW0 “Wiper” terminal of DCP0 FN6332 Rev 2.00 May 28, 2009 DESCRIPTION Page 2 of 13 ISL22429 Absolute Maximum Ratings Thermal Information Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Voltage at any Digital Interface Pin with Respect to GND . . . . . . . . . . . . . . . . . . . . -0.3V to VCC + 0.3 VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6V Voltage at any DCP pin with Respect to GND . . . . . . . -0.3V to VCC IW (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA Latchup (Note 2) . . . . . . . . . . . . . . . . . . Class II, Level B @ +125°C ESD Rating HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5kV CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1kV Thermal Resistance (Typical, Note 1) JA (°C/W) 10 Lead MSOP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Maximum Junction Temperature (Plastic Package). . . . . . . . +150°C Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C VCC Voltage for DCP Operation . . . . . . . . . . . . . . . . . . 2.7V to 5.5V Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -3mA to 3mA Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5mW CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 1. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 2. Jedec Class II pulse conditions and failure criterion used. Level B exceptions are: using a max positive pulse of 6.5V on the SHDN pin, and using a max negative pulse of -0.8V for all pins. Analog Specifications SYMBOL RTOTAL Over recommended operating conditions unless otherwise stated. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. PARAMETER End-to-End Resistance TEST CONDITIONS MIN TYP (Note 3) MAX UNIT W option 10 k U option 50 k End-to-End Resistance Tolerance W and U option End-to-End Temperature Coefficient W option ±50 ppm/°C (Note 13) U option ±80 ppm/°C (Note 13) VCC = 3.3V @ +25°C, wiper current = VCC/RTOTAL 70  25 pF RW (Note 13) Wiper Resistance CW (Note 13) Wiper Capacitance -20 +20 % VOLTAGE DIVIDER MODE (measured at RWi, unloaded; i = 0 or 1) INL (Note 8) Integral Non-linearity Monotonic over all tap positions -1 1 LSB (Note 4) DNL (Note 7) Differential Non-linearity Monotonic over all tap positions -0.5 0.5 LSB (Note 4) ZSerror (Note 5) Zero-scale Error W option 0 1 5 LSB (Note 4) U option 0 0.5 2 LSB (Note 4) W option -5 -1 0 LSB (Note 4) U option -2 -1 0 LSB (Note 4) -2 2 LSB (Note 4) FSerror (Note 6) Full-scale Error VMATCH (Note 9) DCP to DCP Matching Any two DCPs at the same tap position TCV (Note 10) Ratiometric Temperature Coefficient DCP register set to 40 hex FN6332 Rev 2.00 May 28, 2009 ±4 ppm/°C Page 3 of 13 ISL22429 Operating Specifications Over the recommended operating conditions unless otherwise specified. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. SYMBOL ICC1 ICC2 ISB ISD ILkgDig PARAMETER MIN TYP (Note 3) MAX UNIT VCC Supply Current (volatile write/read) 10k DCP, fSPI = 5MHz; (for SPI active, read and write states) 1.4 mA VCC Supply Current (volatile write/read) 50k DCP, fSPI = 5MHz; (for SPI active, read and write states) 450 µA VCC Supply Current (non-volatile write/read) 10k DCP, fSPI = 5MHz; (for SPI active, read and write states) 3.5 mA VCC Supply Current (non-volatile write/read) 50k DCP, fSPI = 5MHz; (for SPI active, read and write states) 2.0 mA VCC Current (standby) VCC = +5.5V, 10k DCP, SPI interface in standby state 1.22 mA VCC = +5.5V, 50k DCP, SPI interface in standby state 320 µA VCC = +3.6V, 10k DCP, SPI interface in standby state 800 µA VCC = +3.6V, 50k DCP, SPI interface in standby state 250 µA VCC = +5.5V @ +85°C, SPI interface in standby state 3 µA VCC = +5.5V@ +125°C, SPI interface in standby state 5 µA VCC = +3.6V @ +85°C, SPI interface in standby state 2 µA VCC = +3.6V @ +125°C, SPI interface in standby state 4 µA 1 µA VCC Current (shutdown) Leakage Current, at Pins SHDN, SCK, Voltage at pin from GND to VCC SDI, SDO and CS tWRT (Note 13) Wiper Response Time after SPI Write to WR Register tShdnRec (Note 13) DCP Recall Time from Shutdown Mode Vpor TEST CONDITIONS Power-on Recall Voltage VccRamp VCC Ramp Rate tD Power-up delay -1 1.5 µs From rising edge of SHDN signal to wiper stored position and RH connection 1.5 µs SCK rising edge of last bit of ACR data byte to wiper stored position and RH connection 1.5 µs Minimum VCC at which memory recall occurs 2.0 2.6 0.2 V V/ms 3 VCC above Vpor, to DCP Initial Value Register recall completed, and SPI Interface in standby state ms EEPROM SPECIFICATION EEPROM Endurance EEPROM Retention tWC (Note 11) Temperature T < +55°C 1,000,000 Cycles 50 Years Non-volatile Write Cycle Time 12 20 ms 0.3*VCC V SERIAL INTERFACE SPECIFICATIONS VIL SHDN, SCK, SDI, and CS Input Buffer LOW Voltage FN6332 Rev 2.00 May 28, 2009 -0.3 Page 4 of 13 ISL22429 Operating Specifications Over the recommended operating conditions unless otherwise specified. (Continued) Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. (Continued) SYMBOL PARAMETER VIH SHDN, SCK, SDI, and CS Input Buffer HIGH Voltage 0.7*VCC Hysteresis SHDN, SCK, SDI, and CS Input Buffer Hysteresis 0.05* VCC VOL TEST CONDITIONS SDO Output Buffer LOW Voltage IOL = 4mA Rpu (Note 12) SDO Pull-up Resistor Off-chip Maximum is determined by tRO and tFO with maximum bus load Cbus = 30pF, fSCK = 5MHz Cpin (Note 13) SHDN, SCK, SDI, SDO and CS Pin Capacitance MIN TYP (Note 3) MAX UNIT VCC+0.3 V V 0 0.4 V 2 k 10 pF fSCK SPI Frequency tCYC SPI Clock Cycle Time 200 ns tWH SPI Clock High Time 100 ns tWL SPI Clock Low Time 100 ns tLEAD Lead Time 250 ns tLAG Lag Time 250 ns tSU SDI, SCK and CS Input Setup Time 50 ns tH SDI, SCK and CS Input Hold Time 50 ns tRI SDI, SCK and CS Input Rise Time 10 ns tFI SDI, SCK and CS Input Fall Time 10 20 ns SDO Output Disable Time 0 100 ns 350 ns tDIS 5 MHz tV SDO Output Valid Time tHO SDO Output Hold Time tRO SDO Output Rise Time Rpu = 2k, Cbus = 30pF 60 ns tFO SDO Output Fall Time Rpu = 2k, Cbus = 30pF 60 ns tCS CS Deselect Time 0 ns 2 µs NOTES: 3. Typical values are for TA = +25°C and 3.3V supply voltage. 4. LSB: [V(RW)127 – V(RW)0]/127. V(RW)127 and V(RW)0 are V(RW) for the DCP register set to 7F hex and 00 hex respectively. LSB is the incremental voltage when changing from one tap to an adjacent tap. 5. ZS error = V(RW)0/LSB. 6. FS error = [V(RW)127 – VCC]/LSB. 7. DNL = [V(RW)i – V(RW)i-1]/LSB-1, for i = 1 to 127. i is the DCP register setting. 8. INL = [V(RW)i – i • LSB – V(RW)]/LSB for i = 1 to 127 9. VMATCH = [V(RWx)i – V(RWy)i]/LSB, for i = 1 to 127, x = 0 to 3 and y = 0 to 3. Max  V  RW  i  – Min  V  RW  i  10 6 10. TC = ---------------------------------------------------------------------------------------------  ----------------- for i = 16 to 112 decimal, T = -40°C to +125°C. Max( ) is the maximum value of the wiper V  Max  V  RW  i  + Min  V  RW  i    2 165°C voltage and Min ( ) is the minimum value of the wiper voltage over the temperature range. 11. tWC is the time from the end of a Write sequence of SPI serial interface, to the end of the self-timed internal non-volatile write cycle. 12. Rpu is specified for the highest data rate transfer for the device. Higher value pull-up can be used at lower data rates. 13. This parameter is not 100% tested. FN6332 Rev 2.00 May 28, 2009 Page 5 of 13 ISL22429 Timing Diagrams Input Timing tCS CS tCYC tLEAD SCK tSU tH ... tWL tRI tFI tWH ... MSB SDI tLAG LSB HIGH IMPEDANCE SDO Output Timing CS SCK ... tV tDIS ... MSB SDO SDI tHO LSB ADDR XDCP Timing (for All Load Instructions) CS SCK ... tWRT MSB SDI ... LSB VW SDO HIGH IMPEDANCE FN6332 Rev 2.00 May 28, 2009 Page 6 of 13 ISL22429 Typical Performance Curves 100 1.2 80 1.0 70 60 ISB (µA) WIPER RESISITANCE () 1.4 VCC = 3.3V, T = +125°C 90 50 40 30 T = +25°C 0.2 10 0 0.6 0.4 VCC = 3.3V, T = -40°C VCC = 3.3V, T = +20°C 20 T = +125°C 0.8 0 20 40 60 80 100 0 2.7 120 3.2 3.7 TAP POSITION (DECIMAL) 4.2 4.7 5.2 VCC (V) FIGURE 2. STANDBY ICC vs VCC FIGURE 1. WIPER RESISTANCE vs TAP POSITION [ I(RW) = VCC/RTOTAL ] FOR 10k (W) 0.2 0.2 T = +25°C T = +25°C VCC = 2.7V 0.1 INL (LSB) DNL (LSB) 0.1 0 -0.1 VCC = 2.7V 0 -0.1 VCC = 5.5V -0.2 0 20 40 VCC = 5.5V 60 80 100 -0.2 120 0 20 40 60 80 100 120 TAP POSITION (DECIMAL) TAP POSITION (DECIMAL) FIGURE 4. INL vs TAP POSITION IN VOLTAGE DIVIDER MODE FOR 10k (W) FIGURE 3. DNL vs TAP POSITION IN VOLTAGE DIVIDER MODE FOR 10k (W) 1.3 0.0 10k 1.1 -0.3 ZSERROR (LSB) ZSERROR (LSB) 0.9 0.7 0.5 VCC = 2.7V VCC = 5.5V 0.3 0.1 -0.3 -40 -20 0 20 40 60 80 TEMPERATURE (°C) FIGURE 5. FSERROR vs TEMPERATURE FN6332 Rev 2.00 May 28, 2009 VCC = 5.5V 50k -0.6 -0.9 10k -1.2 50k -0.1 VCC = 2.7V 100 120 -1.5 -40 -20 0 20 40 60 80 100 TEMPERATURE (ºC) FIGURE 6. FSERROR vs TEMPERATURE Page 7 of 13 120 ISL22429 Typical Performance Curves (Continued) 105 90 0.5 75 VCC = 2.7V TCv (ppm/°C) END TO END RTOTAL CHANGE (%) 1.0 50k 0.0 VCC = 5.5V 10k -0.5 60 45 50k 30 10k 15 -1.0 -40 -20 0 20 40 60 80 100 120 0 16 36 56 TEMPERATURE (ºC) FIGURE 7. END TO END RTOTAL % CHANGE vs TEMPERATURE 76 96 TAP POSITION (DECIMAL) FIGURE 8. TC FOR VOLTAGE DIVIDER MODE IN ppm SCL SIGNAL AT WIPER (WIPER UNLOADED) SIGNAL AT WIPER (WIPER UNLOADED MOVEMENT FROM 7Fh TO 00h) FIGURE 9. MIDSCALE GLITCH, CODE 80h TO 7Fh FIGURE 10. LARGE SIGNAL SETTLING TIME Pin Description Potentiometer Pins RWI (I = 0, 1) RW RWi is the wiper terminal and is equivalent to the movable terminal of a mechanical potentiometer. The position of the wiper within the array is determined by the WRi register. SHDN The SHDN pin forces the resistors to end-to-end open circuit condition and shorts RWi to GND. When SHDN is returned to logic high, the previous latch settings put RWi at the same resistance setting prior to shutdown. This pin is logically AND with SHDN bit in ACR register. SPI interface is still available in shutdown mode and all registers are accessible. This pin must remain HIGH for normal operation. FIGURE 11. DCP CONNECTION IN SHUTDOWN MODE Bus Interface Pins SERIAL CLOCK (SCK) This is the serial clock input of the SPI serial interface. SERIAL DATA OUTPUT (SDO) The SDO is an open drain serial data output pin. During a read cycle, the data bits are shifted out at the falling edge of the serial clock SCK, while the CS input is low. SDO requires an external pull-up resistor for proper operation. FN6332 Rev 2.00 May 28, 2009 Page 8 of 13 ISL22429 SERIAL DATA INPUT (SDI) The SDI is the serial data input pin for the SPI interface. It receives device address, operation code, wiper address and data from the SPI external host device. The data bits are shifted in at the rising edge of the serial clock SCK, while the CS input is low. CHIP SELECT (CS) CS LOW enables the ISL22429, placing it in the active power mode. A HIGH to LOW transition on CS is required prior to the start of any operation after power up. When CS is HIGH, the ISL22429 is deselected and the SDO pin is at high impedance, and (unless an internal write cycle is underway) the device will be in the standby state. WRi and IVRi can be read or written to directly using the SPI serial interface as described in the following sections. Memory Description The ISL22429 contains seven non-volatile and three volatile 8bit registers. The memory map of ISL22429 is on Table 1. The two non-volatile registers (IVRi) at address 0 and 1, contain initial wiper value and volatile registers (WRi) contain current wiper position. In addition, five non-volatile General Purpose registers from address 2 to address 6 are available. TABLE 1. MEMORY MAP ADDRESS NON-VOLATILE VOLATILE 8 — ACR 7 Principles of Operation The ISL22429 is an integrated circuit incorporating two DCPs with its associated registers, non-volatile memory and the SPI serial interface providing direct communication between host and potentiometers and memory. The resistor array is comprised of individual resistors connected in series. At either end of the array and between each resistor is an electronic switch that transfers the potential at that point to the wiper. The electronic switches on the device operate in a “make before break” mode when the wiper changes tap positions. When the device is powered down, the last value stored in IVRi will be maintained in the non-volatile memory. When power is restored, the contents of the IVRi is recalled and loaded into the corresponding WRi to set the wiper to the initial value. Reserved 6 5 4 3 2 General Purpose General Purpose General Purpose General Purpose General Purpose Not Available Not Available Not Available Not Available Not Available 1 0 IVR1 IVR0 WR1 WR0 The non-volatile IVRi and volatile WRi registers are accessible with the same address. The Access Control Register (ACR) contains information and control bits described below in Table 2. The VOL bit (ACR[7]) determines whether the access is to wiper registers WRi or initial value registers IVRi. TABLE 2. ACCESS CONTROL REGISTER (ACR) DCP Description Each DCP is implemented with a combination of resistor elements and CMOS switches. The physical ends of each DCP are equivalent to the fixed terminals of a mechanical potentiometer and internally connected to Vcc and GND. The RW pin of each DCP is connected to intermediate nodes, and is equivalent to the wiper terminal of a mechanical potentiometer. The position of the wiper terminal within the DCP is controlled by volatile Wiper Register (WR). Each DCP has its own WR. When the WR of a DCP contains all zeroes (WR[6:0] = 00h), its wiper terminal (RW) is closest to GND. When the WR register of a DCP contains all ones (WR[6:0] = 7Fh), its wiper terminal (RW) is closest to VCC. As the value of the WR increases from all zeroes (0) to all ones (127 decimal), the wiper moves monotonically from the position closest to GND to the closest to VCC. While the ISL22429 is being powered up, all two WRs are reset to 40h (64 decimal), which locates RW roughly at the center between GND and Vcc. After the power supply voltage becomes large enough for reliable non-volatile memory reading, all WRs will be reload with the value stored in corresponding non-volatile Initial Value Registers (IVRs). BIT # 7 6 5 4 3 2 1 0 Bit Name VOL SHDN WIP 0 0 0 0 0 If VOL bit is 0, the non-volatile IVRi register is accessible. If VOL bit is 1, only the volatile WRi is accessible. Note, value is written to IVRi register also is written to the WRi. The default value of this bit is 0. The SHDN bit (ACR[6]) disables or enables Shutdown mode. This bit is logically AND with SHDN pin. When this bit is 0, DCPs are in Shutdown mode. The default value of SHDN bit is 1. The WIP bit (ACR[5]) is read only bit. It indicates that non-volatile write operation is in progress. The WIP bit can be read repeatedly after a non-volatile write to determine if the write has been completed. It is impossible to write to the IVRi, WRi or ACR while WIP bit is 1. Shutdown Mode The device can be put in Shutdown mode either by pulling the SHDN pin to GND or setting the SHDN bit in the ACR register to 0. The truth table for Shutdown mode is in Table 3. The SPI interface register address bits have to be set to 0000b or 0001b to access the WR of DCP0 or DCP1 respectively. The FN6332 Rev 2.00 May 28, 2009 Page 9 of 13 ISL22429 Write Operation TABLE 3. SHDN pin SHDN bit Mode High 1 Normal operation Low 1 Shutdown High 0 Shutdown Low 0 Shutdown SPI Serial Interface The ISL22429 supports an SPI serial protocol, mode 0. The device is accessed via the SDI input and SDO output with data clocked in on the rising edge of SCK, and clocked out on the falling edge of SCK. CS must be LOW during communication with the ISL22429. SCK and CS lines are controlled by the host or master. The ISL22429 operates only as a slave device. A Write operation to the ISL22429 is a three-byte operation. It requires first, the CS transition from HIGH to LOW, then a valid Identification Byte, then a valid instruction byte following by Data Byte is sent to SDI pin. The host terminates the write operation by pulling the CS pin from LOW to HIGH. For a write to addresses 0000b or 0001b, the MSB at address 8 (ACR[7]) determines if the Data Byte is to be written to volatile or both volatile and non-volatile registers. Refer to “Memory Description” on page 9 and Figure 12. Device can receive more than one byte of data by auto incrementing the address after each received byte. Note after reaching the address 0110b, the internal pointer “rolls over” to address 0000b. All communication over the SPI interface is conducted by sending the MSB of each byte of data first. The internal non-volatile write cycle starts after rising edge of CS and takes up to 20ms. Thus, non-volatile registers must be written individually. Protocol Conventions Read Operation The first byte sent to the ISL22429 from the SPI host is the Identification Byte. A valid Identification Byte contains 0101 as the four MSBs, with the following four bits set to 0. A read operation to the ISL22429 is a three-byte operation. It requires first, the CS transition from HIGH to LOW, then a valid Identification Byte, then a valid instruction byte following by “dummy” Data Byte is sent to SDI pin. The SPI host reads the data from SDO pin on falling edge of SCK. The host terminates the read operation by pulling the CS pin from LOW to HIGH (see Figure 13). TABLE 4. IDENTIFICATION BYTE FORMAT 0 1 0 1 0 0 0 (MSB) 0 (LSB) The next byte sent to the ISL22429 contains the instruction and register pointer information. The four MSBs are the instruction and four LSBs are register address (see Table 5). TABLE 5. IDENTIFICATION BYTE FORMAT 7 6 5 4 3 2 1 0 I3 I2 I1 I0 R3 R2 R1 R0 There are only two valid instruction sets: 1011(binary) - is a Read operation 1100(binary) - is a Write operation FN6332 Rev 2.00 May 28, 2009 The ISL22429 will provide the Data Bytes to the SDO pin as long as SCK is provided by the host from the registers indicated by an internal pointer. This pointer initial value is determined by the register address in the Read operation instruction, and increments by one during transmission of each Data Byte. After reaching the memory location 0110b, the pointer “rolls over” to 0000b, and the device continues to output the data for each received SCK clock. In order to read back the non-volatile IVR, it is recommended that the application reads the ACR first to verify the WIP bit is 0. If the WIP bit (ACR[5]) is not 0, the host should repeat its reading sequence again. Page 10 of 13 ISL22429 CS SCK SDI 0 1 0 1 0 0 0 0 0 I3 I2 I1 I0 R3 R2 R1 R0 0 D6 D5 D4 D3 D2 D1 D0 D3 D2 D1 D0 FIGURE 12. THREE BYTE WRITE SEQUENCE CS SCK SDI Don’t Care 0 1 0 1 0 0 0 0 0 I3 I2 I1 I0 R3 R2 R1 R0 SDO 0 D6 D5 D4 FIGURE 13. THREE BYTE READ SEQUENCE Applications Information Communicating with ISL22429 Communication with ISL22429 proceeds using SPI interface through the ACR (address 1000b), IVRi (addresses 0000b, 0001b) and WRi (addresses 0000b, 0001b) registers. The wiper of the potentiometer is controlled by the WRi register. Writes and reads can be made directly to these registers to control and monitor the wiper position without any non-volatile memory changes. This is done by setting MSB bit at address 1000b to 1. The non-volatile IVRi stores the power up value of the wiper. IVRs are accessible when MSB bit at address 1000b is set to 0. Writing a new value to the IVRi register will set a new power up position for the wiper. Also, writing to this register will load the same value into the corresponding WRi as the IVRi. Reading from the IVRi will not change the WRi, if its contents are different. FN6332 Rev 2.00 May 28, 2009 Page 11 of 13 ISL22429 Examples: B. Reading from the WR: This sequence will read the value from the WR1 (volatile): Write to ACR first to access the volatile WRs Send the ID byte, Instruction Byte, then the Data byte 0 1 0 1 0 0 0 0 1 1 0 0 1 0 0 0 1 1 0 0 (Sent to SDI) 0 Read the data from WR1 (Addr 0001b) Send the ID byte, Instruction Byte, then Read the Data byte 0 1 0 1 0 0 0 0 1 0 1 1 0 0 0 1 x x x x x (Out on SDO) 0 0 0 x x x A. Writing to the IVR: This sequence will write a new value (77h) to the IVR0(non-volatile): Set the ACR (Addr 1000b) for NV write (40h) Send the ID byte, Instruction Byte, then the Data byte 0 1 0 1 0 0 0 0 1 1 0 0 1 0 0 0 0 1 0 0 (Sent to SDI) 0 0 0 0 Set the IVR0 (Addr 0000b) to 77h Send the ID byte, Instruction Byte, then the Data byte 0 1 0 1 0 0 0 0 1 1 0 0 0 0 0 0 0 1 1 1 (Sent to SDI) 0 1 1 1 © Copyright Intersil Americas LLC 2006-2009. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN6332 Rev 2.00 May 28, 2009 Page 12 of 13 ISL22429 Mini Small Outline Plastic Packages (MSOP) N M10.118 (JEDEC MO-187BA) 10 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE E1 E INCHES SYMBOL -B- INDEX AREA 1 2 0.20 (0.008) A B C TOP VIEW 4X  0.25 (0.010) R1 R GAUGE PLANE SEATING PLANE -CA 4X  A2 A1 b -H- 0.10 (0.004) L SEATING PLANE C -A- e D 0.20 (0.008) C C a SIDE VIEW CL E1 0.20 (0.008) C D -B- END VIEW MILLIMETERS MAX MIN MAX NOTES A 0.037 0.043 0.94 1.10 - A1 0.002 0.006 0.05 0.15 - A2 0.030 0.037 0.75 0.95 - b 0.007 0.011 0.18 0.27 9 c 0.004 0.008 0.09 0.20 - D 0.116 0.120 2.95 3.05 3 E1 0.116 0.120 2.95 3.05 4 e L1 MIN 0.020 BSC 0.50 BSC - E 0.187 0.199 4.75 5.05 - L 0.016 0.028 0.40 0.70 6 L1 0.037 REF 0.95 REF - N 10 10 7 R 0.003 - 0.07 - - R1 0.003 - 0.07 - -  5o 15o 5o 15o -  0o 6o 0o 6o Rev. 0 12/02 NOTES: 1. These package dimensions are within allowable dimensions of JEDEC MO-187BA. 2. Dimensioning and tolerancing per ANSI Y14.5M-1994. 3. Dimension “D” does not include mold flash, protrusions or gate burrs and are measured at Datum Plane. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E1” does not include interlead flash or protrusions and are measured at Datum Plane. - H - Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per side. 5. Formed leads shall be planar with respect to one another within 0.10mm (.004) at seating Plane. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension “b” does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm (0.003 inch) total in excess of “b” dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Datums -A -H- . and - B - to be determined at Datum plane 11. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only FN6332 Rev 2.00 May 28, 2009 Page 13 of 13