R5323N

'2001.7.10 SOT23-6 150mA 2ch LDO REGULATORS R5323N SERIES s OUTLINE The R5323N Series are voltage regulator ICs with high output voltage accuracy, low supply current, low dropout, and high ripple rejection by CMOS process. Each of these voltage regulator ICs consists of a voltage reference unit, an error amplifier, resistors for setting Output Voltage, a current limit circuit, and a chip enable circuit. These ICs perform with low dropout voltage due to built-in transistor with low ON resistance, and a chip enable function prolongs the battery life of each system. The line transient response and load transient response of the R5323N Series are excellent, thus these ICs are very suitable for the power supply for hand-held communication equipment. The output voltage of these ICs is internally fixed with high accuracy. Since the package for these ICs is SOT-23-6 package, 2ch LDO regulators are included in each package, high density mounting of the ICs on boards is possible. s FEATURES Low Supply Current .................................................. TYP. 90µA(VR1,VR2) Standby Mode ........................................................... TYP. 0.1µA(VR1,VR2) Low Dropout Voltage ................................................ TYP. 0.22V(IOUT=150mA Output Voltage=3.0V Type) High Ripple Rejection ............................................... TYP. 75dB(VOUT≤2.4V), TYP. 70dB(VOUT≥2.5V) (f=1kHz) ........................................................................................... TYP. 65dB(VOUT≤2.4V), TYP. 60dB(VOUT≥2.5V) (f=10kHz) Low Temperature-Drift Coefficient of Output Voltage TYP. ±100ppm/°C Excellent Line Regulation ......................................... TYP. 0.02%/V High Output Voltage Accuracy.................................. ±2.0% Small Package ..........................................................SOT-23-6 Output Voltage...........................................................Stepwise setting with a step of 0.1V in the range of 1.5V to 4.0V is possible Built-in chip enable circuit (A/B: active high) Built-in fold-back protection circuit ..........................TYP. 40mA (Current at short mode) Ceramic Capacitor is recommended. (1µF or more) s APPLICATIONS Power source for handheld communication equipment. Power source for electrical appliances such as cameras, VCRs and camcorders. Power source for battery-powered equipment. Rev. 1.10 -1- s BLOCK DIAGRAM R5323NXXXA R5323NXXXB C16 E E rror 1 V C1 E O T1 U R 1_1 A p. m + R 2_1 C urrent Lim it 6 E rror 1 A p. m V ref + R 2_1 R 1_1 VUT1 O V ref VDD 2 + C urrent Lim it R 1_2 5 C urrent Lim it G D VD 2 ND A p. m + R 2_2 R 1_2 N 5 GD E rror A p. m V ref E rror R 2_2 V ref C2 4 E 3 V UT2 C 2 4 E O C urrent Lim it 3 VUT2 O s SELECTION GUIDE The output voltage, mask option, and the taping type for the ICs can be selected at the user's request. The selection can be made with designating the part number as shown below; R5323NXXXX-XX ←Part Number ↑ ↑↑ abc Code a b c Contents Setting combination of 2ch Output Voltage (VOUT) : Serial Number for Voltage Setting, Stepwise setting with a step of 0.1V in the range of 1.5V to 4.0V is possible for each channel. Designation of Mask Option : A version: without auto discharge function at OFF state. B version: with auto discharge function at OFF state. Designation of Taping Type : Ex. TR (refer to Taping Specifications; TR type is the standard direction.) Rev. 1.10 -2- s PIN CONFIGURATION SOT-23-6 6 5 4 CE1 GND CE2 (mark side) VOUT1 VDD VOUT2 1 2 3 s PIN DESCRIPTION Pin No. 1 2 3 4 5 6 VDD VOUT2 CE2 GND CE1 Symbol VOUT1 Input Pin Output Pin 2 Chip Enable Pin 2 Ground Pin Chip Enable Pin 1 Description Output Pin 1 s ABSOLUTE MAXIMUM RATINGS Item Input Voltage Input Voltage(CE Pin) Output Voltage Output Current 1 Output Current 2 Power Dissipation Operating Temperature Range Storage Temperature Range Symbol VIN VCE VOUT IOUT1 IOUT2 PD Topt Tstg Rating 6.5 -0.3 ~ VIN+0.3 -0.3 ~ VIN+0.3 200 200 250 -40 ~ 85 -55 ~ 125 Unit V V V mA mA mW °C °C Rev. 1.10 -3- s ELECTRICAL CHARACTERISTICS q R5323NXXXA/B Symbol VOUT IOUT ∆VOUT/∆IOUT VDIF ISS Istandby ∆VOUT/∆VIN Item Topt=25°C Conditions MIN. TYP. MAX. Unit VIN = Set VOUT+1V VOUT VOUT V ×0.98 ×1.02 1mA ≤ IOUT ≤ 30mA VIN - VOUT = 1.0V 150 mA VIN = Set VOUT+1V 15 40 mV 1mA ≤ IOUT ≤ 150mA Refer to the ELECTRICAL CHARACTERISTICS by OUTPUT VOLTAGE VIN = Set VOUT+1V 90 120 µA VIN = Set VOUT+1V 0.1 1.0 µA VCE = GND Set VOUT+0.5V ≤ VIN ≤ 6V 0.02 0.10 %/V IOUT = 30mA Ripple 0.5Vp-p VIN = Set 75 VOUT+1V *Note1 IOUT = 30mA dB 65 ( In case that VOUT≤1.7V, *Note2 VIN = Set VOUT+1.2V) 2.0 6.0 V ppm IOUT = 30mA ±100 /°C -40°C ≤ Topt ≤ 85°C VOUT = 0V 40 mA 0.7 2.0 8.0 MΩ 1.5 0.0 BW=10Hz to 100kHz VCE=0V 30 60 VIN 0.3 V V µVrms Ω Output Voltage Output Current Load Regulation Dropout Voltage Supply Current Supply Current (Standby) Line Regulation RR VIN ∆VOUT/∆T Ilim RPD VCEH VCEL en Ripple Rejection Input Voltage Output Voltage Temperature Coefficient Short Current Limit CE Pull-down Resistance CE Input Voltage “H” CE Input Voltage “L” Output Noise Low Output Nch Tr. ON RLOW Resistance (of B version) Note1: f=1kHz, 70dB as to VOUT≥2.5V Output type. Note2: f=10kHz, 60dB as to VOUT≥2.5V Output type. q ELECTRICAL CHARACTERISTICS by OUTPUT VOLTAGE Topt = 25°C Output Voltage VOUT (V) VOUT = 1.5 VOUT = 1.6 VOUT = 1.7 1.8 ≤ VOUT ≤ 2.0 2.1 ≤ VOUT ≤ 2.7 2.8 ≤ VOUT ≤ 4.0 Dropout Voltage VDIF (V) Condition TYP. 0.38 0.35 IOUT = 150mA 0.33 0.32 0.28 0.22 MAX. 0.70 0.65 0.60 0.55 0.50 0.35 *Recommended Ceramic capacitor for Output: GRM219R61A105K(Murata) General Example of External Components Ceramic Capacitors: C1608X5R0J105K (TDK) GRM188R60J105K (Murata) Rev. 1.10 -4- s TEST CIRCUITS I OUT2 VOUT2 C3 V OUT2 V CE2 R5323N SERIES V DD GND CE1 C1 C3 VOUT2 CE2 R5323N SERIES GND V DD I SS C1 I OUT 1 1 VOUT C2 V OUT1 A C2 VOUT1 CE1 V Fig.1 Standard test Circuit I OUT2 C3 VOUT2 CE2 Fig.2 Supply Current Test Circuit C3 VOUT2 CE2 R5323N SERIES I OUT 2 R5323N SERIES GND V DD Pulse IOUT C2 1 I OUT1a I OUT1b C2 V I OUT2b GND VDD C1 CE1 VOUT1 CE1 PG Generator OUT1 Fig.3 Ripple Rejection, Line Transient Response Test Circuit Fig.4 Load Transient Response Test Circuit s TYPICAL APPLICATION OUT2 1 C3 IN V OUT1 R5323NXXX X SERIES CE1 6 2 OUT1 C1 VDD GND 5 C2 3 V OUT2 CE2 4 (External Components) Output Capacitor; Ceramic Type Rev. 1.10 -5- s TYPICAL CHARACTERISTICS 1) Output Voltage vs. Output Current (Topt=25°C) 1.5V(VR1) 1.5V(VR2) 1.6 1.4 Output Voltage VOUT[V] 1.2 1 0.8 0.6 0.4 0.2 0 0 100 200 300 Output Current IOUT[mA] 2.8V(VR1) VIN=2.5V VIN=3.5V VIN=1.8V VIN=2.0V 1.6 1.4 Output Voltage VOUT[V] 1.2 1 0.8 0.6 0.4 0.2 0 VIN=1.8V VIN=2.5V VIN=2.0V VIN=3.5V 400 0 100 200 300 Output Current IOUT[mA] 2.8V(VR2) 400 3 2.5 Output Voltage VOUT[V] 2 VIN=3.1V 3 2.5 Output Voltage VOUT[V] 2 VIN=3.1V VIN=4.8V VIN=4.8V 1.5 1 1.5 1 0.5 0 0 100 200 300 Output Current IOUT[mA] 4.0V(VR1) 0.5 0 400 0 100 200 300 Output Current IOUT[mA] 4.0V(VR2) 400 5 5 VIN=4.3V Output Voltage VOUT[V] VIN=4.3V Output Voltage VOUT[V] 4 4 3 VIN=6.0V 3 VIN=6.0V 2 2 1 1 0 0 100 200 300 Output Current IOUT[mA] 400 0 0 100 200 300 Output Current IOUT[mA] 400 Rev. 1.10 -6- 2) Output Voltage vs. Input Voltage (Topt=25°C) 1.5V(VR1) 1.5V(VR2) 1.6 1.5 Output Voltage VOUT[V] 1.4 1.3 1.2 1.1 1 1 2 3 4 Input Voltage VIN[V] 2.8V(VR1) 1.6 1.5 Output Voltage VOUT[V] 1.4 1.3 1.2 1.1 1 5 6 1 2 3 4 Input Voltage VIN[V] 2.8V(VR2) 1mA 30mA 50mA 1mA 30mA 50mA 5 6 2.9 2.8 Output Voltage VOUT[V] 2.7 2.6 2.5 2.4 2.3 2.2 2.1 2 1 2 3 4 Input Voltage VIN[V] 4.0V(VR1) 2.9 2.8 Output Voltage VOUT[V] 2.7 2.6 2.5 2.4 2.3 2.2 2.1 2 5 6 1 2 3 4 Input Voltage VIN[V] 4.0V(VR2) 1mA 30mA 50mA 1mA 30mA 50mA 5 6 4.2 4 Output Voltage VOUT[V] 3.8 3.6 3.4 3.2 3 1 2 3 4 Input Voltage VIN[V] 5 6 1mA 30mA 50mA 4.2 4 3.8 3.6 3.4 3.2 3 1 2 3 4 Input Voltage VIN[V] 5 6 1mA 30mA 50mA Rev. 1.10 -7- Output Voltage VOUT[V] 3) Dropout Voltage vs. Temperature 1.5V(VR1) 1.5V(VR2) 0.6 0.5 0.4 0.3 0.2 0.1 0 0 25 50 75 100 125 Output Current IOUT(mA) 2.8V(VR1) Topt=85°C 25°C -40°C 0.6 0.5 Dropout Voltage VDIF(V) 0.4 0.3 0.2 0.1 0 150 0 25 50 75 100 125 Output Current IOUT(mA) 2.8V(VR2) Topt=85°C 25°C -40°C Dropout Voltage VDIF(V) 150 0.4 0.35 Dropout Voltage VDIF(V) 0.3 Topt=85°C 25°C -40°C 0.4 0.35 Dropout Voltage VDIF(V) 0.3 Topt=85°C 25°C -40°C 0.25 0.2 0.25 0.2 0.15 0.1 0.15 0.1 0.05 0 0 25 50 75 100 125 Output Current IOUT(mA) 4.0V(VR1) 0.05 0 150 0 25 50 75 100 125 Output Current IOUT(mA) 4.0V(VR2) 150 0.4 0.35 Dropout Voltage VDIF(V) 0.3 0.25 0.2 0.15 0.1 0.05 0 0 25 50 75 100 Output Current IOUT(mA) 125 150 Topt=85°C 0.4 0.35 Dropout Voltage VDIF(V) 0.3 0.25 0.2 0.15 0.1 0.05 0 0 25 50 75 100 Output Current IOUT(mA) 125 150 Topt=85°C 25°C -40°C 25°C -40°C Rev. 1.10 -8- 4) Output Voltage vs. Temperature 1.5V(VR1) VIN=2.5V IOUT=30mA 1.5V(VR2) VIN=2.5V IOUT=30mA 1.54 1.53 Output Voltage VOUT[V] 1.52 1.51 1.50 1.49 1.48 1.47 1.46 -50 -25 0 25 50 75 Temperature Topt (°C) 2.8V(VR1) VIN=3.8V 1.54 1.53 Output Voltage VOUT[V] 100 1.52 1.51 1.50 1.49 1.48 1.47 1.46 -50 -25 0 25 50 75 Temperature Topt (°C) 2.8V(VR2) 100 2.86 2.84 IOUT=30mA 2.86 2.84 Output Voltage VOUT[V] 2.82 2.80 2.78 2.76 2.74 VIN=3.8V IOUT=30mA Output Voltage VOUT[V] 2.82 2.80 2.78 2.76 2.74 -50 -25 0 25 50 75 Temperature Topt(°C) 4.0V(VR1) 100 -50 -25 0 25 50 75 Temperature Topt(°C) 4.0V(VR2) 100 4.08 4.06 VIN=5.0V IOUT=30mA 4.08 4.06 Output Voltage VOUT[V] 4.04 4.02 4.00 3.98 3.96 3.94 3.92 VIN=5.0V IOUT=30mA Output Voltage VOUT[V] 4.04 4.02 4.00 3.98 3.96 3.94 3.92 -50 -25 0 25 50 75 Temperature Topt(°C) 100 -50 -25 0 25 50 75 周囲温度 Topt (°C) 100 Rev. 1.10 -9- 5) Supply Current vs. Input Voltage (Topt=25°C) 1.5V 2.8V 100 80 100 Supply Current ISS[uA] Supply Current ISS[uA] 80 60 40 VR1 VR2 60 40 VR1 VR2 20 0 0 1 2 3 4 Input Voltage VIN[V] 4.0V 20 0 5 6 0 1 2 3 4 Input Voltage VIN[V] 5 6 100 80 Supply Current ISS[uA] 60 40 VR1 VR2 20 0 0 1 2 3 4 Input Voltage VIN[V] 1.5V(VR1) 5 6 6) Supply Current vs. Temperature VIN=2.5V 1.5V(VR2) 100 80 60 40 20 0 -50 -25 0 25 50 75 Temperature Topt (°C) 100 100 80 60 40 20 0 -50 -25 VIN=2.5V Supply Current ISS[uA] Supply Current ISS[uA] 0 25 50 75 Temperature Topt (°C) 100 Rev. 1.10 - 10 - 2.8V(VR1) 100 80 60 40 20 0 -50 -25 VIN=3.8V 2.8V(VR2) 100 80 60 40 20 0 VIN=3.8V Supply Current ISS[uA] Supply Current ISS[uA] 0 25 50 75 Temperature Topt (°C) 4V(VR1) VIN=5.0V 100 -50 -25 0 25 50 75 Temperature Topt(°C) 4V(VR2) VIN=5.0V 100 100 80 60 40 20 0 -50 -25 100 80 60 40 20 0 Supply Current ISS[uA] Supply Current ISS[uA] 0 25 50 75 (°C) Temperature Topt VR1 100 -50 -25 0 25 50 75 Temperature Topt (°C) VR2 100 7) Dropout Voltage vs. Set Output Voltage 0.6 Dropout Voltage VDIF[V] Topt=25°C 0.6 Dropout Voltage VDIF[V] 10mA 30mA 50mA 150mA 0.5 0.4 0.3 0.2 0.1 0 1 0.5 0.4 0.3 0.2 0.1 0 10mA 30mA 50mA 150mA 2 3 Set Output Voltage Vreg[V] 4 1 2 3 Set Output Voltage Vreg[V] 4 Rev. 1.10 - 11 - 8) Ripple Rejection vs. Frequency (Topt=25°C) 1.5V(VR1) VIN=2.5V+0.5Vp-p 90 80 Ripple Rejection RR[dB] COUT= Ceramic 1.0µF 90 80 Ripple Rejection RR[dB] 70 60 50 40 30 20 10 0 1.5V(VR2) VIN=2.5V+0.5Vp-p COUT= Ceramic 1.0µF 70 60 50 40 30 20 10 0 0.1 1 1.5V(VR1) IOUT=1mA IOUT=30mA IOUT=150mA IOUT=1mA IOUT=30mA IOUT=150mA 10 VIN=2.5V+0.5Vp-p 100 0.1 Frequency ｆ[kHz] COUT= Ceramic 2.2µF 1 10 Frequency ｆ[kHz] 1.5V(VR2) VIN=2.5V+0.5Vp-p 100 90 80 Ripple Rejection RR[dB] 90 80 Ripple Rejection RR[dB] 70 60 50 40 30 20 10 0 IOUT=1mA IOUT=30mA IOUT=150mA COUT= Ceramic 2.2µF 70 60 50 40 30 20 10 0 0.1 1 10 Frequency ｆ[kHz] 2.8V(VR1) VIN=3.8V+0.5Vp-p COUT= Ceramic 1.0µF IOUT=1mA IOUT=30mA IOUT=150mA 100 0.1 1 10 Frequency ｆ[kHz] 2.8V(VR2) VIN=3.8V+0.5Vp-p 100 90 80 Ripple Rejection RR[dB] 70 60 50 40 30 20 10 0 0.1 IOUT=1mA IOUT=30mA IOUT=150mA 90 80 Ripple Rejection RR[dB] 70 60 50 40 30 20 10 0 IOUT=1mA IOUT=30mA IOUT=150mA COUT= Ceramic 1.0µF 1 10 Frequency ｆ [kHz] 100 0.1 1 10 Frequency ｆ[kHz] 100 Rev. 1.10 - 12 - 2.8V(VR1) VIN=3.8V+0.5Vp-p COUT= Ceramic 2.2µF 2.8V(VR2) VIN=3.8V+0.5Vp-p COUT= Ceramic 2.2µF 90 80 Ripple Rejection RR[dB] 90 80 Ripple Rejection RR[dB] 70 60 50 40 30 20 10 0 IOUT=1mA IOUT=30mA IOUT=150mA 70 60 50 40 30 20 10 0 0.1 1 10 Frequency ｆ[kHz] 4.0V(VR1) VIN=5.0V+0.5Vp-p IOUT=1mA IOUT=30mA IOUT=150mA 100 0.1 1 10 Frequency ｆ[kHz] 4.0V(VR2) VIN=5.0V+0.5Vp-p 100 90 80 Ripple Rejection RR[dB] COUT= Ceramic 1.0µF 90 80 Ripple Rejection RR[dB] 70 60 50 40 30 20 10 0 IOUT=1mA IOUT=30mA IOUT=150mA COUT= Ceramic 1.0µF 70 60 50 40 30 20 10 0 0.1 1 10 Frequency ｆ[kHz] 4.0V(VR1) VIN=5.0V+0.5Vp-p COUT= Ceramic 2.2µF IOUT=1mA IOUT=30mA IOUT=150mA 100 0.1 1 10 Frequency ｆ[kHz] 4.0V(VR2) VIN=5.0V+0.5Vp-p COUT= Ceramic 2.2µF 100 90 80 Ripple Rejection RR[dB] 70 60 50 40 30 20 10 0 0.1 IOUT=1mA IOUT=30mA IOUT=150mA 90 80 Ripple Rejection RR[dB] 70 60 50 40 30 20 10 0 0.1 IOUT=1mA IOUT=30mA IOUT=150mA 1 10 Frequency ｆ[kHz] 100 1 10 Frequency ｆ[kHz] 100 Rev. 1.10 - 13 - 9) Ripple Rejection vs. Input Voltage (DC bias) COUT = Ceramic 1.0µF, Topt=25°C 2.8V(VR1) 100 90 Ripple Rejection RR[dB] 70 60 50 40 30 20 10 0 2.9 3.0 80 IOUT=1mA 2.8V(VR2) IOUT=1mA 100 90 Ripple Rejection RR[dB] 80 70 60 50 40 30 20 10 3.3 0 2.9 3.0 f=1kHz f=10kHz f=100kHz f=1kHz f=10kHz f=100kHz 3.1 3.2 Input Voltage VIN[V] 2.8V(VR1) 3.1 3.2 Input Voltage VIN[V] 2.8V(VR2) 3.3 100 90 Ripple Rejection RR[dB] 80 70 60 50 40 30 20 10 0 2.9 3.0 IOUT=30mA 100 90 Ripple Rejection RR[dB] 80 70 60 50 40 30 20 10 3.3 0 2.9 3.0 3.1 IOUT=30mA f=1kHz f=10kHz f=100kHz f=1kHz f=10kHz f=100kHz 3.1 3.2 Input Voltage VIN[V] 3.2 3.3 Input Voltage VIN[V] 2.8V(VR1) 100 90 IOUT=50mA 100 90 Ripple Rejection RR[dB] 80 70 60 50 40 30 20 10 0 2.9 3.0 2.8V(VR2) IOUT=50mA Ripple Rejection RR[dB] 80 70 60 50 40 30 20 10 0 2.9 3.0 3.1 3.2 Input Voltage VIN[V] f=1kHz f=10kHz f=100kHz f=1kHz f=10kHz f=100kHz 3.3 3.1 3.2 Input Voltage VIN[V] 3.3 Rev. 1.10 - 14 - 10) Input Transient Response R5323N001X(2.8V,VR1) IOUT=30mA, tr=tf=5µs COUT= Ceramic 1.0µF 2.85 Output Voltage VOUT[V] 2.84 2.83 2.82 2.81 2.80 2.79 0 10 20 30 40 50 60 Time T[us] 70 80 90 VOUT VIN 6 Input Voltage VIN[V] 5 4 3 2 1 0 100 Topt=25°C COUT= Ceramic 2.2µF R5323N001X(2.8V,VR1) 2.85 Output Voltage VOUT[V] 2.84 2.83 2.82 2.81 2.80 2.79 0 10 20 30 40 50 60 Time T[us] 70 VOUT VIN 6 Input Voltage VIN[V] 5 4 3 2 1 80 90 0 100 Topt=25°C R5323N001X(2.8V,VR1) 2.85 Output Voltage VOUT[V] 2.84 2.83 2.82 2.81 2.80 2.79 0 10 20 30 40 50 60 Time T[us] 70 VOUT VIN COUT= Ceramic 4.4µF 6 Input Voltage VIN[V] 5 4 3 2 1 80 90 0 100 Rev. 1.10 - 15 - R5323N001X(2.8V,VR2) Topt=25°C COUT= Ceramic 1.0µF 2.85 Output Voltage VOUT[V] 2.84 2.83 2.82 2.81 2.80 2.79 0 10 20 30 40 50 Time T[us] R5323N001X(2.8V,VR2) VOUT VIN 6 Input Voltage VIN[V] 5 4 3 2 1 60 70 80 90 0 100 Topt=25°C 2.85 Output Voltage VOUT[V] 2.84 2.83 2.82 2.81 2.80 2.79 0 10 20 30 40 50 60 Time T[us] 70 VIN COUT= Ceramic 2.2µF 6 4 3 2 1 80 90 0 100 VOUT R5323N001X(2.8V,VR2) Topt=25°C COUT= Ceramic 4.4µF 2.85 Output VoltageVOUT[V] 2.84 2.83 2.82 2.81 2.80 2.79 0 10 20 30 40 50 60 Time T[us] VOUT VIN 6 Input VoltageVIN[V] 5 4 3 2 1 0 100 70 80 90 Rev. 1.10 - 16 - Input Voltage VIN[V] 5 11) Load Transient Response Cin=Ceramic1.0uF Cin=Ceramic1.0uF 2.8V(VR1) Output Current IOUT1 [mA] Cout=Ceramic1.0uF 2.8V(VR2) Cout=Ceramic1.0uF 150 100 100 IOUT1 2.85 Output Voltage VOUT[V] 2.80 2.75 50 50 2.85 VOUT1 0 VOUT1 Output Voltage VOUT[V] 2.80 2.75 IOUT1=30mA 2.85 2.80 VOUT2 2.85 2.80 VOUT2 2.75 IOUT2=30mA 0 5 10 Time t [us] 15 20 2.75 0 5 10 Time t[us] 15 20 12) ESR vs. Output Current Topt=25°C CIN = COUT =Ceramic 1.0µF, VIN=2.5V, f=10Hz to 2MHz (BW=30Hz) 1.5V(VR2) 1.5V(VR1) 100 100 10 ESR [Ohm] ESR [Ohm] 10 1 1 0.1 0.1 0.01 0 50 100 Output Current IOUT [mA] 150 0.01 0 50 100 Output Current IOUT [mA] 150 Rev. 1.10 - 17 - Output Current IOUT2 [mA] IOUT2 150 CIN = COUT =Ceramic 1.0µF, VIN=2.5V, f=10Hz to 2MHz (BW=30Hz) 2.8V(VR1) 2.8V(VR2) 100 100 10 ESR [Ohm] ESR [Ohm] 10 1 1 0.1 0.1 0.01 0 50 100 Output Current IOUT [mA] 150 0.01 0 50 100 Output Current IOUT [mA] 150 13) Minimum Operating Voltage 1.5V Minimum Operating Voltage Range 2.3 2.2 2.1 2 VDD(V) 1.9 1.8 1.7 1.6 1.5 0 75 Output Current IOUT(mA) 150 VDD ＶＩＮ（ＭＩＮ） Rev. 1.10 - 18 - s TECHNICAL NOTES When using these ICs, consider the following points: In these ICs, phase compensation is made for securing stable operation even if the load current is varied. For this purpose, be sure to use a 1.0µF or more capacitance COUT with good frequency characteristics and ESR (Equivalent Series Resistance) of which is in the range described as follows: The relations between IOUT (Output Current) and ESR of Output Capacitor are shown in the typical characteristics above. The conditions when the white noise level is under 40µV (Avg.) are marked as the hatched area in the graph. Test these ICs with as same external components as ones to be used on the PCB. Make VDD and GND line sufficient. When the impedance of these is high, the noise might be picked up or not work correctly. Connect the capacitor with a capacitance of 1µF or more between VDD and GND as close as possible. Set external components, especially Output Capacitor, as close as possible to the ICs and make wiring shortest. Rev. 1.10 - 19 -