BA7626F-E2

High performance video signal switcher Five inputs Dual Circuits Video Signal Switchers BA7626F,BA7626FS No.11066EAT01 ●Description The BA7626F/FS is a 5-input video signal switching circuit with a broadband 6 dB amplifier that was developed for AV amplifier input switching. Just by devising a transistor buffer in the output, player switching of two VCR or other videotape players and three DVD players or other playback devices is possible. Moreover, input switching and switching of recording to a VCR or other device also can be performed independently. Since the input circuit of the BA7626F/FS is terminated by 20kΩ impedance, it is suited to not only video signal but also chroma signal or audio signal switching. ●Features 1) 5 input line, 3 output line switching 2) Built-in 6 dB amplifier 3) 5V operating voltage 4) 20kΩ input impedance ●Applications AV amplifiers, Video selectors, etc. ●Line up matrix Part No. BA7626F BA7626FS SOP16 SSOP-A16 Package Input type Bias (R=20kΩ) ●Absolute Maximum Ratings (Ta=25℃) Parameter Supply voltage Power dissipation BA7626F BA7626FS Symbol Ratings Unit Vcc 9 V Pd 300 ※1 600 ※2 mW Operating temperature Topr -25～+70 ℃ Storage temperature Tstg -55～+125 ℃ ※1 Derating is done at 3.0mW/℃ above Ta=25℃.(BA7626F） ※2 Derating is done at 6.0mW/℃ above Ta=25℃.(BA7626FS） ●Operating Range (Ta=25℃) Parameter Power supply voltage www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. Symbol Vcc Ratings Min. Typ. Max. 4.5 5.0 5.5 1/6 Unit V 2011.03 - Rev.A Technical Note BA7626F,BA7626FS ●Electrical characQteristics (Unless otherwise noted Ta=25℃, Vcc=5.0V) Limits Parameter Symbol Min. Typ. Max. Unit Conditions ― Circuit current ICC ― 15.0 20.0 mA Maximum output level Vom 2.3 2.5 ― Vp-p f=1kHz, THD=0.5% Voltage gain GV 5.7 6.2 6.7 dB f=1MHz, VIN=1Vp-p Interchannel crosstalk GT ― -65 -45 dB f=4.43MHz, VIN=1Vp-p CTM ― -35 -25 dB f=4.43MHz, VIN=1Vp-p Frequency characteristic Gf -3 0 +3 dB 10MHz/1MHz, VIN=1Vp-p Input inpedance ZIN 16 20 24 kΩ ― CTL pin switching level VTH 2.2 ― 3.3 V ― Mute level ※ This product is not designed for protection against radioactive rays. ●Truth table Input Output Input Output Input Output A B E MONOUT C D E VOUT1 C D E VOUT2 L L ※ IN1 L L ※ － L L ※ IN1 H L ※ IN2 H L ※ IN2 H L ※ － L H ※ IN3 L H ※ IN3 L H ※ IN3 H H L IN4 H H L IN4 H H L IN4 H H H IN5 H H H IN5 H H H IN5 ※ Indicates “don’t care”(H or L) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 2/6 2011.03 - Rev.A Technical Note BA7626F,BA7626FS ●Block diagram 16 IN1 MONOUT 1 GND 2 IN5 15 CTL A 6dB logic 3 14 VOUT1 GND 4 IN4 13 VCC 5 CTL E 6 IN3 12 IN2 6dB 11 CTL B logic 7 10 VOUT2 CTL D 8 9 CTL C Fig.1 Block diagram ●Application circuit VCC 100 470 + TV 75 2.2 FRONT 1 MONOUT IN1 2 GND CTL A 15 3 IN5 VOUT1 14 4 GND VCC 13 IN4 IN2 12 + 16 VCC 100 + REAR A933 2.2 + 5 75 6 CTL E CTL B 11 7 IN3 VOUT2 10 8 CTL D CTL C 9 103 + + 5.0V + 47 2.2 + VCC 100 470 OUT 75 + 2.2 LD VTR IN1 75 75 BS 75 470 + 2.2 AUX OUT 75 VTR IN2 75 F/R CTL MON CTL REC CTL Fig.2 Application circuit www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 3/6 2011.03 - Rev.A Technical Note BA7626F,BA7626FS ●Pin descriptions (Ta=25℃, VCC=5V) Pin No. Equivalent circuit Pin name BA7626F/FS IN VCC 3 5 7 12 16 IN5 IN4 IN3 IN2 IN1 QN 200 QN 20k QN 4.3V 100A 30k CTL VCC 6 8 9 11 15 CTL E CTL D CTL C CTL B CTL A 50k 50k 2k QN D QP 30k VCC 17k QN3 1 100 MONOUT QN20 MONOUT QN2 QN QN6 VCC QN5 10 14 VOUT2 VOUT1 200A 40k 100 QN20 D VOUT 600A www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 4/6 QN QN15 2011.03 - Rev.A Technical Note BA7626F,BA7626FS ●Notes for use 1) Numbers and data in entries are representative design values and are not guaranteed values of the items. 2) Although we are confident in recommending the sample application circuits, carefully check their characteristics further when using them. When modifying externally attached component constants before use, determine them so that they have sufficient margins by taking into account variations in externally attached components and the Rohm LSI, not only for static characteristics but also including transient characteristics. 3) Absolute maximum ratings If applied voltage, operating temperature range, or other absolute maximum ratings are exceeded, the LSI may be damaged. Do not apply voltages or temperatures that exceed the absolute maximum ratings. If you think of a case in which absolute maximum ratings are exceeded, enforce fuses or other physical safety measures and investigate how not to apply the conditions under which absolute maximum ratings are exceeded to the LSI. 4) GND potential Make the GND pin voltage such that it is the lowest voltage even when operating below it. Actually confirm that the voltage of each pin does not become a lower voltage than the GND pin, including transient phenomena. 5) Thermal design Perform thermal design in which there are adequate margins by taking into account the allowable power dissipation in actual states of use. 6) Shorts between pins and misinstallation When mounting the LSI on a board, pay adequate attention to orientation and placement discrepancies of the LSI. If it is misinstalled and the power is turned on, the LSI may be damaged. It also may be damaged if it is shorted by a foreign substance coming between pins of the LSI or between a pin and a power supply or a pin and a GND. 7) Operation in strong magnetic fields Adequately evaluate use in a strong magnetic field, since there is a possibility of malfunction. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 5/6 2011.03 - Rev.A Technical Note BA7626F,BA7626FS ●Ordering part number B A 7 Part No. 6 2 6 F Part No. 7626 S - Package F: SOP16 FS: SSOP-A16 E 2 Packaging and forming specification E2: Embossed tape and reel SOP16 10 ± 0.2 (MAX 10.35 include BURR) 9 Tape Embossed carrier tape Quantity 2500pcs Direction of feed E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 0.3MIN 4.4±0.2 6.2±0.3 16 1 8 0.11 1.5±0.1 0.15 ± 0.1 0.4 ± 0.1 1.27 0.1 1pin Reel (Unit : mm) Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. SSOP-A16 6.6 ± 0.2 (MAX 6.95 include BURR) Tape Embossed carrier tape Quantity 2500pcs 9 Direction of feed 0.3MIN 4.4±0.2 6.2±0.3 16 15 14 13 12 11 10 1 2 3 4 5 6 7 E2 The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 8 0.11 1.5±0.1 0.15 ± 0.1 0.8 0.1 0.36 ± 0.1 1pin Reel (Unit : mm) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 6/6 Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. 2011.03 - Rev.A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A