LA1130

Ordering number : EN595C Monolithic Linear IC LA1130 AM Tuner for Car Radio Overview The LA1130 is an IC developed for AM tuner systems in car radio applications. It provides low-level local oscillation so that it can be applied in varactor diode tuning applications as well as µ tuning applications. Package Dimensions unit: mm 3020A-SIP16 [LA1130] Functions • RF amplification • MIX • OSC (with ALC) • IF amplification • Detection • AGC (normal) • RF wide-band AGC • Others SANYO: SIP16 Features • Good space factor due to single-end package. • Easy to design printed circuit pattern due to 3mm-pitch pin interval. • Double-balanced type MIX : Improvement in IF interference, spurious interference. • Normal AGC : Less variation in detector output to input. • RF wide-band AGC : Improvement in cross modulation distortion, especially strong input characteristics in varactor diode tuning applications because of low operating level (300mVrms). • AGC drive output for FET : Possible to apply AGC to FET at input stage in varactor diode tuning applications. • ALC at OSC stage : Improvement in tracking error due to stabilized low-level (350mVrms) oscillation output in varactor diode tuning applications. • Reference voltage output : Possible to use 5.6V reference voltage for other bias (FET, etc.). • VCC variation compensation : Less variation in gain, distortion, etc. (7.5 to 16V) • Less ripple voltage : Less modulation of carrier by supply voltage ripple. • Low pop noise : Possible to reduce pop noise at the time of VCC-on, mode-on by selecting AGC time constant. Equivalent Circuit Block Diagram SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN 93097HA (KT)/2248KI/D147KI/4105MW/3163KI, ki No.595-1/5 LA1130 Specifications Maximum Ratings at Ta=25°C, See specified Test Circuit. Parameter Maximum supply voltage Maximum output voltage Maximum input voltage Maximum supply current Maximum flow-out current Allowable power dissipation Operating temperature Storage temperature Symbol VCC max VO5 VO8, 11 VIN max ICC max I3 Pd max Topr Tstg Pin 5 Pins 8, 11 Pin 2 Total of current at pins 5, 7, 8, 11, 13 Pin 3 Ta≤45°C Conditions Pins 7, 13 Ratings 16 17 24 5.6 35 6 520 –20 to +70 –40 to +125 Unit V V V V mA mA mW °C °C Recommended Operating Condition at Ta=25°C Parameter Recommended supply voltage Symbol VCC Conditions Ratings 7.5 to 14.0 Unit V Operating Characteristics at Ta=25°C, VCC=8V, fr=1MHz, fm=400Hz, See specified Test Circuit. Parameter Current drain Detection output Signal to noise ratio Total harmonic distortion Symbol ICC1 ICC2 VO1 VO2 S/N 1 S/N 2 THD1 THD2 THD3 RF AGC voltage (V16) [Reference characteristics] Signal to noise ratio Total harmonic distortion Detection output variation Bandwidth (6dB) (60dB) Selectivity (1 signal) Ripple rejection ratio Local oscillation voltage Local osc drift Whistle RF AGC voltage (V16) RF output voltage IF interference Image frequency interference Vosc ∆Vosc VoscL(515kHz) to VoscH(1660kHz) 2fiTweet 74dBµ input, 400Hz beat max. VRFAGC2 120dBµ input VORF 100dBµ input, ±10kHz fr=600kHz, 15dBµ input fr=1400kHz, 15dBµ input Quiescent 120dBµ input 24dBµ input, 30% mod. 74dBµ input, 30% mod. 24dBµ input, 30% mod. 74dBµ input, 30% mod. 74dBµ input, 30% mod. 74dBµ input, 80% mod. 120dBµ input, 30% mod. 5.2 Conditions Ratings min 12.5 14.0 –31.0 –18.0 16 46 typ 18.0 20.0 –26.5 –15.5 20 50 0.35 0.35 0.35 5.6 31 0.58 0.4 7 30 40 40.5 350 20 –33 1 300 91.5 70.5 1.0 1.5 2.0 5.9 max 24.5 26.5 –12.0 –12.0 Unit mA mA dBm dBm dB dB % % % V dB % dB kHz kHz dB dB mVrms mVrms dB V mVrms dB dB VRFAGC1 Quiescent S/N 3 THD4 ∆VO BW6 BW60 ACA 35dBµ input, 30% mod. 128dBµ input, 80% mod. VO(128dBµ)/VO(74dBµ) 6dB width, 15dBµ input 30% mod. 60dB width, 15dBµ input 30% mod. ±10kHz detuning, 15dBµ input, 30% mod. 100dBµ input, IF VCC (pin 13) ripple level 50Hz to 15dBm No.595-2/5 test circuit. Unit (resistance : Ω, capacitance : F) LA1130 Coil Specification TOKO MITSUMI CMU ZT-01 7BR 5721Z 7MC 5723Y 7MC5722BY 7MC 5725Y 7MC 5724Y CFMA-003 7MC-5919N Application where ceramic filter is used between IF stages SUMIDA Sample Application Circuit (excluding the area bounded by the dotted line) / also used as characteristics L1 L2 L3 L5 T1 T2 T3 T4 T5 T6 51N-190-154 58H-190-036 49H-190-036 58H-190-037 58H-190-035 No.595-3/5 Detection output – dBm Current drain – mA Det. output, Noise voltage – dBm Maximum usable sensitivity – dBµ Allowable power dissipation, Pd max – mW 80 % 30 % m mo od Ambient temperature, Ta – °C fr=1000kHz 400Hz–30% mod Total harmonic distortion, THD – % Current drain, ICC – mA LA1130 Input voltage, VIN – dBµ Total harmonic distortion, THD – % Det. output – dBm No.595-4/5 AGC voltage, V16 – V Total harmonic distortion, THD – % RF AGC voltage, V16 – V d Supply voltage, VCC – V VCC=8V 400Hz mod fr=1000kHz fr=1000kHz 400Hz–30% mod VCC=8V Ambient temperature, Ta – °C LA1130 Maximum, usable sensitivity – dBµ S/N, IF interference, Iimage freq. interference – dB OSC voltage, V4 – mV VCC=8V 400Hz–30% mod VCC=8V 400Hz–30% mod Receiving frequency, fr – kHz No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property lose. Anyone purchasing any products described or contained herein for an above-mentioned use shall: Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: Not impose any responsibilty for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of September, 1997. Specifications and information herein are subject to change without notice. RF AGC voltage, V16 – V No.595-5/5