LC372100PM-20LV

Ordering number : EN*5088C CMOS IC LC372100PP, PM, PT-10/20LV 2 MEG (262144 words × 8 bits) Mask ROM Internal Clocked Silicon Gate Preliminary Overview The LC372100PP, LC372100PM and LC372100PT are 262,144-word × 8-bit organization (2,097,152-bit) mask programmable read only memories. The LC372100PP-10, LC372100PM-10 and LC372100PT-10 feature an access time of 100 ns, an OE access time of 40 ns, and a standby current of 30 µA, and are optimal for use in 5-V systems that require high-speed access. The LC372100PP-20LV, LC372100PM-20LV and LC372100PT-20LV feature an access time of 200 ns, an OE access time of 80 ns, and a standby current of 4 µA, and thus are optimal for use in 3-V systems that use batteries. Additionally, they provide high-speed access in 3.3-V systems (3.0 to 3.6 V) with a 150-ns access time and a 60-ns OE access time. These ROMs adopt the JEDEC standard pin assignment which allows them to replace EPROM easily. To prevent bus line collisions in multi-bus microcontroller systems, pin 24 can be mask programmed to be either active high or active low. Package Dimensions unit: mm 3192-DIP32 [LC372100PP] SANYO: DIP32 unit: mm 3205-SOP32 [LC372100PM] Features • 262144 words × 8 bits organization • Power supply LC372100PP, PM, PT-10: 5.0 V ± 10% LC372100PP, PM, PT-20LV: 2.7 to 3.6 V • Fast access time (tAA, tCA) LC372100PP, PM, PT-10: 100 ns (max.) LC372100PP, PM, PT-20LV: 200 ns (max.) 150 ns (VCC = 3.0 to 3.6 V) • Operating current LC372100PP, PM, PT-10: 70 mA (max.) LC372100PP, PM, PT-20LV: 20 mA (max.) • Standby current LC372100PP, PM, PT-10: 30 µA (max.) LC372100PP, PM, PT-20LV: 5 µA (max.) • Full static operation (internal clocked type) • Fully TTL compatible (5 V supply) • 3 state outputs • JEDEC standard pin configuration • Package type LC372100PP-10/20LV: DIP32 (600 mil) LC372100PM-10/20LV: SOP32 (525 mil) LC372100PT-10/20LV: TSOP32 (8 mm × 20 mm) SANYO: SOP32 unit: mm 3224-TSOP32 [LC372100PT] SANYO: TSOP32 (type-I) SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 53098HA (OT)/51195TH (OT)/41095TH (OT) No. 5088-1/5 LC372100PP, PM, PT-10/20LV Pin Assignments Pin Functions A0 to A17 D0 to D7 CE/CE OE/OE VCC VSS Address input Data output Chip enable input Output enable input Power supply Ground Block Diagram Truth Table CE/CE L/H H/L OE/OE X L/H Output Current drain High-impedance Standby mode High-impedance Operating mode DOUT Operating mode H/L H/L X: H or L level should be offered. No. 5088-2/5 LC372100PP, PM, PT-10/20LV Specifications Absolute Maximum Ratings *1 Parameter Maximum supply voltage Supply input voltage Supply output voltage Allowable power dissipation Operating temperature Storage temperature Symbol VCC max VIN VOUT Pd max Topr Tstg Ta = 25°C; Reference values for the SANYO DIP package Conditions Ratings –0.3 to +7.0 –0.3*2 to VCC + 0.3 –0.3 to VCC + 0.3 1.0 0 to +70 –55 to +125 Unit V V V W °C °C Note: 1. Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation should be restricted to Recommended Operating Conditions. 2. VIN (min) = –3.0 V (pulse width ≤ 30 ns) Input/Output Capacitance* at Ta = 25°C, f = 1.0 MHz Parameter Input capacitance Output capacitance Symbol CIN COUT Conditions VIN = 0 V; Reference values for the SANYO DIP package VOUT = 0 V; Reference values for the SANYO DIP package Ratings min typ max 8 10 Unit pF pF Note: * This parameter is periodically sampled and not 100% tested. 3 V Operation DC Recommended Operating Ranges at Ta = 0 to +70°C Parameter Supply voltage Input high level voltage Input low level voltage Symbol VCC max VIH VIL Conditions Ratings min 2.7 0.8 VCC –0.3 typ 3.0 max 3.6 VCC + 0.3 +0.4 Unit V V V DC Electrical Characteristics at Ta = 0 to +70°C, VCC = 2.7 to 3.6 V Parameter Symbol ICCA1 ICCA2 ICCS1 ICCS2 ILI ILO VOH VOL Conditions CE = 0.2 V (CE = VCC – 0.2 V), VI = VCC – 0.2 V/0.2 V CE = VIL (CE = VIH), IO = 0 mA, VI = VIH/VIL, f = 5 MHz CE = VCC – 0.2 V (CE = 0.2 V) CE = VIH (CE = VIL) VIN = 0 to VCC CE or OE = VIH (CE or OE = VIL), VOUT = 0 to VCC IOH = –0.5 mA IOL = 0.5 mA VCC – 0.2 0.2 Ratings min typ max 15 20 5 (0.5*) 50 (10*) ±1.0 ±1.0 Unit mA mA µA µA µA µA V V Operating supply current Standby supply current Input leakage current Output leakage current Output high level voltage Output low level voltage Note: * Guaranteed at Ta = 25°C AC Characteristics at Ta = 0 to +70°C, VCC = 2.7 to 3.6 V Parameter Cycle time Address access time CE access time OE access time Output hold time Output disable time*1 Symbol tCYC tAA tCA tOA tOH tOD*1 25 50 Conditions Ratings min 200 (150*2) 200 (150*2) 200 (150*2) 80 (60*2) typ max Unit ns ns ns ns ns ns Note: 1. tOD is measured from the earlier edge of the CE (CE) or OE(OE)’s going high impedance. This parameter is periodically sampled and not 100% tested. 2. Guaranteed at VCC = 3.0 to 3.6 V No. 5088-3/5 LC372100PP, PM, PT-10/20LV 5 V Operation DC Recommended Operating Ranges at Ta = 0 to +70°C Parameter Supply voltage Input high level voltage Input low level voltage Symbol VCC max VIH VIL Conditions Ratings min 4.5 2.2 –0.3 typ 5.0 max 5.5 VCC + 0.3 +0.6 Unit V V V DC Electrical Characteristics at Ta = 0 to +70°C, VCC = 5.0 V ±10% Parameter Symbol ICCA1 ICCA2 ICCS1 ICCS2 ILI ILO VOH VOL Conditions CE = 0.2 V (CE = VCC – 0.2 V), VI = VCC – 0.2 V/0.2 V CE = VIL (CE = VIH), IO = 0 mA, VI = VIH/VIL, f = 10 MHz CE = VCC – 0.2 V (CE = 0.2 V) CE = VIH (CE = VIL) VIN = 0 to VCC CE or OE = VIH (CE or OE = VIL), VOUT = 0 to VCC IOH = –1.0 mA IOL = 2.0 mA 2.4 0.4 Ratings min typ max 30 70 30 (1.0*) 1.0 (300*) ±1.0 ±1.0 Unit mA mA µA mA (µA) µA µA V V Operating supply current Standby supply current Input leakage current Output leakage current Output high level voltage Output low level voltage Note: * Guaranteed at Ta = 25°C AC Characteristics at Ta = 0 to +70°C, VCC = 5.0 V ±10% Parameter Cycle time Address access time CE access time OE access time Output hold time Output disable time* Symbol tCYC tAA tCA tOA tOH tOD 20 30 Conditions Ratings min 100 100 100 40 typ max Unit ns ns ns ns ns ns Note: * tOD is measured from the earlier edge of the CE (CE) or OE(OE)’s going high impedance. This parameter is periodically sampled and not 100% tested. AC Test Conditions Input pulse levels Input rise/fall time Input timing level Output timing level Output load 0.4 V to 0.8 VCC (3 V measurement), 0.4 V to 2.8 V (5 V measurement) 5 ns 1.5 V 1.5 V 70 pF (3 V measurement) See figure (5 V measurement) Output Load (5 V measurement) No. 5088-4/5 LC372100PP, PM, PT-10/20LV Timing Chart System Design Notes These LSIs adopt an internal synchronization technique in which operation is started by detecting changes in either the CE input or the address inputs. As a result, the output data immediately after power on is invalid. Once power has been applied, valid data is output after the application changes the value of either the CE input or at least one of the address inputs. Another point due to the use of the ATD technique is that these LSIs are extremely sensitive to input noise. Applications must take precautions to provide stable input signals, both for the CE input and the address inputs, to prevent incorrect operation. s No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. s Anyone purchasing any products described or contained herein for an above-mentioned use shall: Œ Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use:  Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. s Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of May, 1998. Specifications and information herein are subject to change without notice. PS No. 5088-5/5