BFC14

LAB SOT–227 Package Outline. Dimensions in mm (inches) 3 1 .5 (1 .2 4 0 ) 3 1 .7 (1 .2 4 8 ) 7 .8 (0 .3 0 7 ) 8 .2 (0 .3 2 2 ) 1 1 .8 (0 .4 6 3 ) 1 2 .2 (0 .4 8 0 ) W = 4 .1 (0 .1 6 1 ) 4 .3 (0 .1 6 9 ) 4 .8 (0 .1 8 7 ) H= 4 .9 (0 .1 9 3 ) (4 places) 1 2 .6 (0 .4 9 6 ) 1 2 .8 (0 .5 0 4 ) 2 5 .2 (0 .9 9 2 ) 2 5 .4 (1 .0 0 0 ) 8 .9 (0 .3 5 0 ) 9 .6 (0 .3 7 8 ) SEME BFC14 4TH GENERATION MOSFET Hex Nut M 4 (4 places) 1 R 2 4 .0 (0 .1 5 7 ) 4 .2 (0 .1 6 5 ) 0 .7 5 (0 .0 3 0 ) 0 .8 5 (0 .0 3 3 ) N–CHANNEL ENHANCEMENT MODE HIGH VOLTAGE ISOLATED POWER MOSFETS 4 3.3 (0 .1 2 9) 3.6 (0.14 3 ) 1 4 .9 (0.58 7 ) 1 5 .1 (0.59 4 ) 3 0 .1 (1 .1 8 5 ) 3 0 .3 (1 .1 9 3 ) 3 8 .0 (1.4 9 6 ) 3 8 .2 (1.5 0 4 ) 3 5 .1 (0 .2 0 1 ) 5 .9 (0 .2 3 2 ) 1 .9 5 (0 .0 7 7 ) 2 .1 4 (0 .0 8 4 ) R= 4 .0 (0 .1 57 ) (2 P lac e s) VDSS 400V 56A ID(cont) RDS(on) 0.075Ω * Source 2 may be omitted, shorted to Source 1 or used for Gate drive circuit. Terminal 1 Source 2* Terminal 3 Gate Terminal 2 Terminal 4 Drain Source 1 ABSOLUTE MAXIMUM RATINGS (Tcase = 25°C unless otherwise stated) VDSS ID IDM , ILM VGS PD TJ , TSTG TL Drain – Source Voltage Continuous Drain Current Pulsed Drain Current 1 and Inductive Current Clamped Gate – Source Voltage Total Power Dissipation @ Tcase = 25°C Linear Derating Factor Operating and Storage Junction Temperature Range Lead Temperature : 0.063” from Case for 10 Sec. 400 56 224 ±30 520 4.16 –55 to 150 300 V A A V W W / °C °C STATIC ELECTRICAL RATINGS (Tcase = 25°C unless otherwise stated) Characteristic BVDSS ID(ON) RDS(ON) IDSS IGSS VGS(TH) Drain – Source Breakdown Voltage On State Drain Current 2 Drain – Source On State Resistance 2 Zero Gate Voltage Drain Current (VGS = 0V) Gate – Source Leakage Current Gate Threshold Voltage Test Conditions VGS = 0V , ID = 250µA VDS > ID(ON) x RDS(ON) Max VGS = 10V VGS =10V , ID = 0.5 ID [Cont.] VDS = VDSS VDS = 0.8VDSS , TC = 125°C VGS = ±30V , VDS = 0V VDS = VGS , ID = 2.5mA 2 Min. 400 56 0.075 250 1000 ±100 4 Typ. Max. Unit V A Ω µA nA V 1) Repetitive Rating: Pulse Width limited by maximum junction temperature. 2) Pulse Test: Pulse Width < 380µS , Duty Cycle < 2% Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. Prelim. 1/94 LAB DYNAMIC CHARACTERISTICS Ciss Coss Crss Qg Qgs Qgd td(on) tr td(off) tf Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Total Gate Charge3 Gate – Source Charge Gate – Drain (“Miller”) Charge Turn–on Delay Time Rise Time Turn-off Delay Time Fall Time Test Conditions VGS = 0V VDS = 25V f = 1MHz VGS = 10V VDD = 0.5 VDSS ID = ID [Cont.] @ 25°C VGS = 15V VDD = 0.5 VDSS ID = ID [Cont.] @ 25°C RG = 0.6Ω Min. Typ. 5630 1320 510 241 34 117 16 31 45 13 Max. Unit 6800 1950 720 370 50 180 32 62 70 26 ns nC pF SEME BFC14 SOURCE – DRAIN DIODE RATINGS AND CHARACTERISTICS IS ISM VSD trr Qrr Characteristic Continuous Source Current (Body Diode) Pulsed Source Current1(Body Diode) Diode Forward Voltage2 Reverse Recovery Time Reverse Recovery Charge VGS = 0V , IS = – ID [Cont.] IS = – ID [Cont.] dls / dt = 100A/µs 185 4 370 8 Test Conditions Min. Typ. Max. Unit 56 A 224 1.8 740 16 V ns µC PACKAGE CHARACTERISTICS LD LS VIsolation CIsolation Torque Characteristic Internal Drain Inductance (Measured From Drain Terminal to Centre of Die) Internal Source Inductance (Measured From Source Terminals to Source Bond Pads) RMS Voltage (50–60 Hz Sinusoidal Waveform From Terminals to Mounting Base for 1 Min.) Drain-to-Mounting Base Capacitance f = 1MHz 2500 35 13 Min. Typ. 3 5 Max. Unit nH V pF in–lbs Maximum Torque for Device Mounting Screws and Electrical Terminations THERMAL CHARACTERISTICS RθJC RθCS Characteristic Junction to Case Case to Sink (Use High Efficiency Thermal Joint Compound and Planar Heat Sink Surface.) 1) Repetitive Rating: Pulse Width limited by maximum junction temperature. 2) Pulse Test: Pulse Width < 380µS , Duty Cycle < 2% 3) See MIL–STD–750 Method 3471 Min. Typ. Max. Unit 0.24 °C/W 0.05 CAUTION — Electrostatic Sensitive Devices. Anti-Static Procedures Must Be Followed. Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. Prelim. 1/94