SGM7SZ04XN5G/TR

SGM7SZ04 Small Logic Inverter GENERAL DESCRIPTION FEATURES The SGM7SZ04 is a single inverter with the advanced ● Wide Supply Voltage Range: 1.65V to 5.5V CMOS technology. The supply voltage pin of this ● Inputs Over-Voltage Tolerance Makes 5V to 3V device accepts any voltage from 1.65V to 5.5V. The Translation Available input can tolerate the maximum of 6V, regardless of the ● +24mA/-24mA Output Current at VCC = 3V supply voltage range. When VCC is 0V, the input and ● Ultra-High Speed: tPD of 4.2ns (TYP) into 50pF at VCC = 3.3V output are in the high-impedance state. This device can achieve ultra-high speed operation with high output drive, meanwhile, the low static power dissipation is maintained over the wide supply voltage operating range. The SGM7SZ04 is available in Green UTDFN-1.45×1-6L, ● Support LCX Performance at VCC = 3.3V ● Power Down High-Impedance Input/Output ● -40℃ to +125℃ Operating Temperature Range ● Available in Green UTDFN-1.45×1-6L, SC70-5 and SOT-23-5 Packages SC70-5 and SOT-23-5 packages. It operates over an ambient temperature range of -40℃ to +125℃. LOGIC SYMBOL A FUNCTION TABLE Y INPUT OUTPUT A Y L H H L � Y=A H = High Voltage Level L = Low Voltage Level SG Micro Corp www.sg-micro.com SEPTEMBER 2022 – REV. A. 4 SGM7SZ04 Small Logic Inverter PACKAGE/ORDERING INFORMATION MODEL SGM7SZ04 PACKAGE DESCRIPTION SPECIFIED TEMPERATURE RANGE ORDERING NUMBER PACKAGE MARKING PACKING OPTION SC70-5 -40℃ to +125℃ SGM7SZ04XC5G/TR SF3XX Tape and Reel, 3000 SOT-23-5 -40℃ to +125℃ SGM7SZ04XN5G/TR SF4XX Tape and Reel, 3000 UTDFN-1.45×1-6L -40℃ to +125℃ SGM7SZ04XUDL6G/TR TCX Tape and Reel, 5000 MARKING INFORMATION NOTE: X = Date Code. XX = Date Code. SC70-5/SOT-23-5 UTDFN-1.45×1-6L YY X YYY X X Date Code - Month Date Code - Year Serial Number Date Code - Year Serial Number Green (RoHS & HSF): SG Micro Corp defines "Green" to mean Pb-Free (RoHS compatible) and free of halogen substances. If you have additional comments or questions, please contact your SGMICRO representative directly. ABSOLUTE MAXIMUM RATINGS Supply Voltage Range, VCC.................................. -0.5V to 6V DC Input Voltage Range, VIN ............................... -0.5V to 6V DC Output Voltage Range, VOUT .......................... -0.5V to 6V DC Input Diode Current, IIK (VIN < -0.5V) ..................... -50mA DC Output Diode Current, IOK (VOUT < -0.5V) ............... -50mA DC Output Current, IOUT .............................................. ±50mA DC VCC or Ground Current, ICC or IGND ........................ ±50mA Package Thermal Resistance SC70-5, θJA ............................................................ 373℃/W SOT-23-5, θJA......................................................... 376℃/W UTDFN-1.45×1-6L, θJA........................................... 332℃/W Junction Temperature .................................................+150℃ Storage Temperature Range ........................ -65℃ to +150℃ Lead Temperature (Soldering, 10s) ............................+260℃ ESD Susceptibility HBM ............................................................................. 8000V MM ................................................................................. 400V RECOMMENDED OPERATING CONDITIONS Operating Temperature Range ..................... -40℃ to +125℃ SG Micro Corp www.sg-micro.com OVERSTRESS CAUTION Stresses beyond those listed in Absolute Maximum Ratings may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Functional operation of the device at any conditions beyond those indicated in the Recommended Operating Conditions section is not implied. ESD SENSITIVITY CAUTION This integrated circuit can be damaged if ESD protections are not considered carefully. SGMICRO recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because even small parametric changes could cause the device not to meet the published specifications. DISCLAIMER SG Micro Corp reserves the right to make any change in circuit design, or specifications without prior notice. SEPTEMBER 2022 2 SGM7SZ04 Small Logic Inverter PIN CONFIGURATIONS (TOP VIEW) 1 A 2 GND 3 SYYxx NC (TOP VIEW) 5 4 VCC Y SOT-23-5/SC70-5 NC 1 6 VCC A 2 5 NC GND 3 4 Y UTDFN-1.45×1-6L PIN DESCRIPTION PIN NAME SOT-23-5/SC70-5 UTDFN-1.45×1-6L 1 1, 5 NC 2 2 A 3 3 GND 4 4 Y 5 6 VCC SG Micro Corp www.sg-micro.com FUNCTION No Connection. Data Input. Unused input must be held high or low. It may not float. Ground. Data Output. Power Supply. SEPTEMBER 2022 3 SGM7SZ04 Small Logic Inverter ELECTRICAL CHARACTERISTICS (Full = -40℃ to +125℃, typical values are at TA = +25℃, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS VCC (V) MIN TYP MAX UNITS General Power Supply Range Supply Voltage Data Retention Input Voltage Output Voltage Input Rise and Fall Times 1.65 5.50 1.50 5.50 VIN 0.00 5.50 V VOUT 0.00 VCC V 1.8, 2.5 ± 0.2 0 20 3.3 ± 0.3 0 10 5.0 ± 0.5 0 5 0.75 × VCC VCC tR, tF V ns/V DC Performance High-Level Input Voltage VIH 1.65 to 5.5 Low-Level Input Voltage VIL 1.65 to 5.5 VOH VIN = VIL 1.62 1.65 1.80 1.77 1.80 2.30 2.27 2.30 3.00 2.97 3.00 4.50 4.47 4.50 IOH = -4mA 1.65 1.46 1.55 IOH = -8mA 2.30 2.01 2.18 IOH = -16mA 3.00 2.49 2.81 IOH = -24mA 3.00 2.30 2.70 IOH = -32mA 4.50 3.98 4.20 Input Leakage Current VOL IIN VIN = VIH V 0.00 0.02 1.80 0.00 0.02 2.30 0.00 0.02 3.00 0.00 0.02 4.50 0.00 0.02 IOL = 4mA 1.65 0.06 0.12 IOL = 8mA 2.30 0.09 0.18 IOL = 16mA 3.00 0.16 0.33 IOL = 24mA 3.00 0.24 0.51 IOL = 32mA 4.50 0.29 0.58 0 to 5.5 ±0.10 ±5 μA 0 0.10 5 μA 1.65 to 5.5 0.10 10 μA VIN = 5.5V, GND Power-Off Leakage Current IOFF VIN or VOUT = 5.5V Quiescent Supply Current ICC VIN = 5.5V, GND SG Micro Corp www.sg-micro.com V 1.65 IOL = 100µA Low-Level Output Voltage 0.20 × VCC 1.65 IOH = -100µA High-Level Output Voltage V V SEPTEMBER 2022 4 SGM7SZ04 Small Logic Inverter ELECTRICAL CHARACTERISTICS (continued) (Full = -40℃ to +125℃, typical values are at TA = +25℃, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS AC Performance VCC = 1.65V VCC = 1.80V VCC = 2.50V ± 0.20V Propagation Delay tPHL, tPLH VCC = 3.30V ± 0.30V 9.6 CL = 15pF, RL = 1MΩ, Figure 1, Figure 2 VCC = 5.00V ± 0.50V VCC = 3.30V ± 0.30V VCC = 5.00V ± 0.50V Input Capacitance CIN Power Dissipation Capacitance (2) CPD VCC = 5.00V 4.9 3.7 ns 2.8 CL = 50pF, RL = 500Ω, Figure 1, Figure 2 VCC = 0V VCC = 3.30V 7.9 4.2 3.2 4.0 Figure 3 16.0 19.0 pF pF NOTES: 1. Unused input must be held high or low. It may not float. 2. CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD) at no output loading and operating at 50% duty cycle (see Figure 3). CPD is related to dynamic operating current ICCD by the expression: ICCD = (CPD) (VCC) (fIN) + (ICC,Static). SG Micro Corp www.sg-micro.com SEPTEMBER 2022 5 SGM7SZ04 Small Logic Inverter TEST CIRCUITS VCC Input Output CL RL NOTE: RL: Load resistance. CL: Load and stray capacitance. Input PRR = 1.0MHz; tW = 500ns. Figure 1. AC Test Circuit tR = 3ns tF = 3ns VCC 90% Input GND 90% 50% 50% 10% 10% tW tPLH tPHL VOH Output 50% 50% VOL Figure 2. AC Waveforms VCC A Input NOTE: Input = AC Waveform; tR = tF = 1.8ns; PRR = 10MHz; Duty Cycle = 50%. Figure 3. ICCD Test Circuit SG Micro Corp www.sg-micro.com SEPTEMBER 2022 6 SGM7SZ04 Small Logic Inverter REVISION HISTORY NOTE: Page numbers for previous revisions may differ from page numbers in the current version. SEPTEMBER 2022 ‒ REV.A.3 to REV.A.4 Page Updated Absolute Maximum Ratings section ....................................................................................................................................................... 2 SEPTEMBER 2021 ‒ REV.A.2 to REV.A.3 Page Updated Package Outline Dimensions section ................................................................................................................................................ 8, 9 FEBRUARY 2021 ‒ REV.A.1 to REV.A.2 Page Changed operating temperature range .............................................................................................................................................................. All APRIL 2014 ‒ REV.A to REV.A.1 Page Added UTDFN-1.45×1-6L package.................................................................................................................................................................... All Changes from Original (OCTOBER 2013) to REV.A Page Changed from product preview to production data ............................................................................................................................................. All SG Micro Corp www.sg-micro.com SEPTEMBER 2022 7 PACKAGE INFORMATION PACKAGE OUTLINE DIMENSIONS SOT-23-5 1.90 D e1 E1 2.59 E 0.99 b e 0.95 0.69 RECOMMENDED LAND PATTERN (Unit: mm) L A2 A ccc C SEATING PLANE A1 θ C Symbol c 0.25 Dimensions In Millimeters MIN MOD MAX A - - 1.450 A1 0.000 - 0.150 A2 0.900 - 1.300 b 0.300 - 0.500 c 0.080 - 0.220 D 2.750 - 3.050 E 1.450 - 1.750 E1 2.600 - 3.000 e 0.950 BSC e1 1.900 BSC L 0.300 - 0.600 θ 0° - 8° ccc 0.100 NOTES: 1. This drawing is subject to change without notice. 2. The dimensions do not include mold flashes, protrusions or gate burrs. 3. Reference JEDEC MO-178. SG Micro Corp www.sg-micro.com TX00033.001 PACKAGE INFORMATION PACKAGE OUTLINE DIMENSIONS SC70-5 D e1 0.65 e E1 1.9 E 0.75 b 0.4 1.3 RECOMMENDED LAND PATTERN (Unit: mm) L L1 A θ A1 c 0.20 A2 Symbol Dimensions In Millimeters MIN MAX Dimensions In Inches MIN MAX A 0.800 1.100 0.031 0.043 A1 0.000 0.100 0.000 0.004 A2 0.800 1.000 0.031 0.039 b 0.150 0.350 0.006 0.014 c 0.080 0.220 0.003 0.009 D 2.000 2.200 0.079 0.087 E 1.150 1.350 0.045 0.053 E1 2.150 2.450 0.085 0.096 e 0.65 TYP 0.026 TYP e1 1.300 BSC 0.051 BSC L 0.525 REF 0.021 REF L1 0.260 0.460 0.010 0.018 θ 0° 8° 0° 8° NOTES: 1. Body dimensions do not include mode flash or protrusion. 2. This drawing is subject to change without notice. SG Micro Corp www.sg-micro.com TX00043.001 PACKAGE INFORMATION PACKAGE OUTLINE DIMENSIONS UTDFN-1.45×1-6L e D N6 E L DETAIL A PIN 1# TOP VIEW DETAIL B N1 b L1 BOTTOM VIEW SEATING PLANE 0.30 A C 0.49 A2 A1 eee C 0.75 SIDE VIEW L (L1) L2 ALTERNATE A-1 ALTERNATE A-3 ALTERNATE A-2 0.5 DETAIL A ALTERNATE TERMINAL CONSTRUCTION RECOMMENDED LAND PATTERN (Unit: mm) A2 ALTERNATE B-1 ALTERNATE B-2 A1 ALTERNATE B-3 DETAIL B ALTERNATE CONSTRUCTION Symbol Dimensions In Millimeters MIN MAX Dimensions In Inches MIN MAX A 0.450 0.600 0.018 0.024 A1 0.000 0.050 0.000 0.002 A2 0.150 REF 0.006 REF D 1.374 1.526 0.054 0.060 E 0.924 1.076 0.036 0.042 b 0.150 0.300 0.006 0.012 e 0.500 TYP 0.020 TYP eee 0.050 0.002 L 0.250 0.450 0.010 0.018 L1 0.250 0.500 0.010 0.020 L2 0.000 0.100 0.000 0.004 NOTE: This drawing is subject to change without notice. SG Micro Corp www.sg-micro.com TX00069.002 PACKAGE INFORMATION TAPE AND REEL INFORMATION REEL DIMENSIONS TAPE DIMENSIONS P2 W P0 Q1 Q2 Q1 Q2 Q1 Q2 Q3 Q4 Q3 Q4 Q3 Q4 B0 Reel Diameter A0 P1 K0 Reel Width (W1) DIRECTION OF FEED NOTE: The picture is only for reference. Please make the object as the standard. KEY PARAMETER LIST OF TAPE AND REEL Reel Diameter Reel Width W1 (mm) A0 (mm) B0 (mm) K0 (mm) P0 (mm) P1 (mm) P2 (mm) W (mm) Pin1 Quadrant SOT-23-5 7″ 9.5 3.20 3.20 1.40 4.0 4.0 2.0 8.0 Q3 SC70-5 7″ 9.5 2.25 2.55 1.20 4.0 4.0 2.0 8.0 Q3 UTDFN-1.45×1-6L 7″ 9.5 1.15 1.60 0.75 4.0 4.0 2.0 8.0 Q1 SG Micro Corp www.sg-micro.com TX10000.000 DD0001 Package Type PACKAGE INFORMATION CARTON BOX DIMENSIONS NOTE: The picture is only for reference. Please make the object as the standard. KEY PARAMETER LIST OF CARTON BOX Length (mm) Width (mm) Height (mm) Pizza/Carton 7″ (Option) 368 227 224 8 7″ 442 410 224 18 SG Micro Corp www.sg-micro.com DD0002 Reel Type TX20000.000