6ES71316BH012BA0

Data sheet 6ES7131-6BH01-2BA0 SIMATIC ET 200SP, Digital input module, DI 16x 24V DC Standard, type 3 (IEC 61131), sink input, (PNP, P-reading), Packing unit: 10 Pieces, fits to BU-type A0, Colour Code CC00, input delay time 0,05..20ms, diagnostics wire break, diagnostics supply voltage General information Product type designation DI 16x24VDC ST HW functional status From FS02 Firmware version V0.0 ● FW update possible No usable BaseUnits BU type A0 Color code for module-specific color identification plate CC00 Product function ● I&M data Yes; I&M0 to I&M3 ● Isochronous mode No Engineering with ● STEP 7 TIA Portal configurable/integrated from version V14 ● STEP 7 configurable/integrated from version V5.5 SP3 ● PCS 7 configurable/integrated from version V8.1 SP1 ● PROFIBUS from GSD version/GSD revision One GSD file each, Revision 3 and 5 and higher ● PROFINET from GSD version/GSD revision GSDML V2.3 Operating mode ● DI Yes ● Counter No ● Oversampling No ● MSI No Supply voltage Rated value (DC) 24 V permissible range, lower limit (DC) 19.2 V permissible range, upper limit (DC) 28.8 V Reverse polarity protection Yes Input current Current consumption, max. 90 mA Encoder supply 24 V encoder supply ● 24 V No Power loss Power loss, typ. 1.7 W Address area Address space per module ● Inputs 6ES71316BH012BA0 Page 1/2 2 byte; + 2 bytes for QI information 1.20.2021 Subject to change without notice © Copyright Siemens Hardware configuration Automatic encoding Yes ● Mechanical coding element Yes ● Type of mechanical coding element Type A Selection of BaseUnit for connection variants ● 1-wire connection BU type A0 ● 2-wire connection BU type A0 + Potential distributor module ● 3-wire connection BU type A0 + Potential distributor module ● 4-wire connection BU type A0 + Potential distributor module Digital inputs Number of digital inputs 16 Digital inputs, parameterizable Yes Input characteristic curve in accordance with IEC 61131, type 3 Yes Input voltage ● Rated value (DC) 24 V — 24 V DC Yes ● for signal "0" -30 to +5 V ● for signal "1" +11 to +30V Input current ● for signal "1", typ. 2.5 mA Input delay (for rated value of input voltage) for standard inputs — parameterizable Yes; 0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms (in each case + delay of 30 to 500 µs, depending on line length) — at "0" to "1", min. 0.05 ms — at "0" to "1", max. 20 ms — at "1" to "0", min. 0.05 ms — at "1" to "0", max. 20 ms Cable length ● shielded, max. 1 000 m ● unshielded, max. 600 m Encoder Connectable encoders ● 2-wire sensor — permissible quiescent current (2-wire sensor), max. Yes 1.5 mA Interrupts/diagnostics/status information Diagnostics function Yes Alarms ● Diagnostic alarm Yes Diagnoses ● Diagnostic information readable Yes ● Monitoring the supply voltage Yes — parameterizable Yes ● Monitoring of encoder power supply No ● Wire-break Yes; Module-by-module, optional protective circuit for preventing wirebreak diagnostics in the case of simple encoder contacts: 25 kOhm to 45 kOhm ● Short-circuit No ● Group error Yes Diagnostics indication LED ● Monitoring of the supply voltage (PWR-LED) Yes; green PWR LED ● Channel status display Yes; green LED ● for channel diagnostics No ● for module diagnostics Yes; green/red DIAG LED Potential separation Potential separation channels ● between the channels 6ES71316BH012BA0 Page 2/3 No 1.20.2021 Subject to change without notice © Copyright Siemens ● between the channels and backplane bus Yes ● between the channels and the power supply of the electronics No Isolation Isolation tested with 707 V DC (type test) Ambient conditions Ambient temperature during operation ● horizontal installation, min. -30 °C; < 0 °C as of FS02 ● horizontal installation, max. 60 °C ● vertical installation, min. -30 °C; < 0 °C as of FS02 ● vertical installation, max. 50 °C Altitude during operation relating to sea level ● Installation altitude above sea level, max. 5 000 m; Restrictions for installation altitudes > 2 000 m, see manual Dimensions Width 15 mm Height 73 mm Depth 58 mm Weights Weight, approx. 28 g last modified: 1/16/2021 6ES71316BH012BA0 Page 3/3 1.20.2021 Subject to change without notice © Copyright Siemens