6ES71316BF000DA0

Data sheet 6ES7131-6BF00-0DA0 SIMATIC ET 200SP, digital input module, DI 8x 24 V DC High Speed, Pack quantity: 1 unit, three alternative operating modes: DI, Oversampling, 4x counters, suitable for BU type A0, Color code CC01 General information Product type designation DI 8x24 V DC HS HW functional status from FS04 Firmware version ● FW update possible Yes usable BaseUnits BU type A0 Color code for module-specific color identification plate CC01 Product function ● I&M data Yes; I&M0 to I&M3 ● Isochronous mode Yes Engineering with ● STEP 7 TIA Portal configurable/integrated from version V13 SP1 ● STEP 7 configurable/integrated from version V5.5 SP3 / - ● PROFIBUS from GSD version/GSD revision One GSD file each, Revision 3 and 5 and higher ● PROFINET from GSD version/GSD revision GSDML V2.3 Operating mode ● DI Yes ● Counter Yes ● Oversampling Yes ● MSI No Supply voltage Rated value (DC) 24 V permissible range, lower limit (DC) 19.2 V permissible range, upper limit (DC) 28.8 V Reverse polarity protection Yes Input current Current consumption, max. 70 mA; without sensor supply Encoder supply 24 V encoder supply ● 24 V Yes ● Short-circuit protection Yes; per module, electronic ● Output current, max. 700 mA Power loss Power loss, typ. 1.5 W Address area Address space per module 6ES71316BF000DA0 Page 1/2 1.19.2021 Subject to change without notice © Copyright Siemens ● Address space per module, max. 45 byte ● Inputs 32 byte; 1 byte + 1 byte for QI information in DI mode; 32 bytes in Oversampling mode; 25 bytes in Counter mode ● Outputs 20 byte; In count mode Hardware configuration Automatic encoding Yes ● Mechanical coding element Yes ● Type of mechanical coding element Type A Selection of BaseUnit for connection variants ● 1-wire connection BU type A0 ● 2-wire connection BU type A0 ● 3-wire connection BU type A0 with AUX terminals ● 4-wire connection BU type A0 + external terminals Digital inputs Number of digital inputs 8 Pulse extension Yes ● Length 2 s; 50 ms, 100 ms, 200 ms, 500 ms, 1 s, 2 s Digital input functions, parameterizable ● Gate start/stop Yes ● Freely usable digital input Yes ● Counter Yes — Number, max. 4 — Counting frequency, max. 10 kHz — Counting width 32 bit — Counting direction up/down Yes ● Digital input with oversampling Yes — Number, max. 8 — Values per cycle, max. 32 — Resolution, min. 7.8125 µs Input voltage ● Rated value (DC) 24 V ● for signal "0" -30 to +5 V ● for signal "1" +11 to +30V Input current ● for signal "1", typ. 6 mA Input delay (for rated value of input voltage) for standard inputs — parameterizable Yes; none / 0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms for interrupt inputs — parameterizable Yes for technological functions — parameterizable Yes Cable length ● shielded, max. 50 m ● unshielded, max. 50 m Encoder Connectable encoders ● 2-wire sensor — permissible quiescent current (2-wire sensor), max. Yes 1.5 mA Isochronous mode Bus cycle time (TDP), min. 125 µs Jitter, max. 5 µs Interrupts/diagnostics/status information Diagnostics function Yes Alarms ● Diagnostic alarm Yes ● Hardware interrupt Yes 6ES71316BF000DA0 Page 2/3 1.19.2021 Subject to change without notice © Copyright Siemens Diagnoses ● Diagnostic information readable Yes ● Monitoring the supply voltage Yes — parameterizable Yes ● Monitoring of encoder power supply Yes; Module-wise ● Wire-break No ● Short-circuit Yes; Module-wise Diagnostics indication LED ● Monitoring of the supply voltage (PWR-LED) Yes; green PWR LED ● Channel status display Yes; green LED ● for channel diagnostics No ● for module diagnostics Yes; green/red DIAG LED Potential separation Potential separation channels ● between the channels No ● between the channels and backplane bus Yes ● between the channels and the power supply of the electronics No Isolation Isolation tested with 707 V DC (type test) Standards, approvals, certificates Suitable for safety functions No Ambient conditions Ambient temperature during operation ● horizontal installation, min. -30 °C; < 0 °C as of FS04 ● horizontal installation, max. 60 °C ● vertical installation, min. -30 °C; < 0 °C as of FS04 ● vertical installation, max. 50 °C Altitude during operation relating to sea level ● Installation altitude above sea level, max. 5 000 m; Restrictions for installation altitudes > 2 000 m, see manual Dimensions Width 15 mm Height 73 mm Depth 58 mm Weights Weight, approx. 28 g last modified: 1/16/2021 6ES71316BF000DA0 Page 3/3 1.19.2021 Subject to change without notice © Copyright Siemens