6ES71435BF000BA0

Data sheet 6ES7143-5BF00-0BA0 SIMATIC ET 200AL, DIQ 4+DQ 4x 24 V DC/0.5 A, 8XM8, Degree of protection IP67 General information Product type designation DIQ 4+DQ 4x24VDC/0.5A HW functional status E01 Firmware version V1.0.x Product function ● I&M data Yes; I&M0 to I&M3 Engineering with ● STEP 7 TIA Portal configurable/integrated from version STEP 7 V13 SP1 or higher ● STEP 7 configurable/integrated from version From V5.5 SP4 Hotfix 3 ● PROFIBUS from GSD version/GSD revision GSD as of Revision 5 ● PROFINET from GSD version/GSD revision GSDML V2.3.1 Supply voltage Load voltage 1L+ ● Rated value (DC) 24 V ● permissible range, lower limit (DC) 20.4 V ● permissible range, upper limit (DC) 28.8 V ● Reverse polarity protection Yes; Against destruction; encoder power supply outputs applied with reversed polarity, loads pick up Load voltage 2L+ ● Rated value (DC) 24 V ● permissible range, lower limit (DC) 20.4 V ● permissible range, upper limit (DC) 28.8 V ● Reverse polarity protection Yes; against destruction; load increasing Input current Current consumption (rated value) 40 mA; without load from load voltage 1L+ (unswitched voltage) 4 A; Maximum value from load voltage 2L+, max. 4 A; Maximum value Encoder supply Number of outputs 4 24 V encoder supply ● Short-circuit protection Yes; per module, electronic ● Output current, max. 0.7 A; Total current of all encoders Power loss Power loss, typ. 2.5 W Digital inputs Number of digital inputs 4; Parameterizable as DIQ Input characteristic curve in accordance with IEC 61131, type 3 Yes Number of simultaneously controllable inputs 6ES71435BF000BA0 Page 1/3 7/9/2022 Subject to change without notice © Copyright Siemens all mounting positions — up to 55 °C, max. 4 Input voltage ● Rated value (DC) 24 V ● for signal "0" -3 to +5V ● for signal "1" +11 to +30V Input current ● for signal "1", typ. 3.2 mA Input delay (for rated value of input voltage) for standard inputs — at "0" to "1", min. 1.2 ms — at "0" to "1", max. 4.8 ms — at "1" to "0", min. 1.2 ms — at "1" to "0", max. 4.8 ms Cable length ● unshielded, max. 30 m Digital outputs Number of digital outputs ● in groups of Short-circuit protection ● Response threshold, typ. Limitation of inductive shutdown voltage to 8; 4 DQ fixed, 4 DIQ parameterizable 4; 2 load groups for 4 outputs each Yes; per channel, electronic 0.7 A 2L+ (-47 V) Switching capacity of the outputs ● on lamp load, max. 5W Load resistance range ● lower limit 48 Ω ● upper limit 4 kΩ Output voltage ● for signal "1", min. L+ (-0.8 V) Output current ● for signal "1" rated value 0.5 A ● for signal "0" residual current, max. 0.5 mA Switching frequency ● with resistive load, max. 100 Hz ● with inductive load, max. 0.5 Hz ● on lamp load, max. 1 Hz Total current of the outputs ● Current per group, max. 2A Cable length ● unshielded, max. 30 m Encoder Connectable encoders ● 2-wire sensor — permissible quiescent current (2-wire sensor), max. Yes 1.5 mA Interrupts/diagnostics/status information Substitute values connectable Yes; channel by channel, parameterizable Alarms ● Diagnostic alarm Yes; Parameterizable Diagnoses ● Short-circuit Yes; Outputs to M; encoder supply to M; module by module Diagnostics indication LED ● Channel status display Yes; green LED ● for module diagnostics Yes; green/red LED ● For load voltage monitoring Yes; green LED Potential separation between the load voltages Yes Potential separation channels ● between the channels, in groups of 4; DIQ channels are isolated from DQ channels ● between the channels and backplane bus Yes 6ES71435BF000BA0 Page 2/3 7/9/2022 Subject to change without notice © Copyright Siemens ● between the channels and the power supply of the electronics No; DIQ channels are non-isolated and DQ channels are isolated from supply voltage 1L+ Isolation Isolation tested with 707 V DC (type test) Degree and class of protection IP degree of protection IP65/67 Standards, approvals, certificates Suitable for safety-related tripping of standard modules Yes; From FS01 Highest safety class achievable for safety-related tripping of standard modules ● Performance level according to ISO 13849-1 PL d ● Category according to ISO 13849-1 Cat. 3 ● SIL acc. to IEC 62061 SIL 2 Ambient conditions Ambient temperature during operation ● min. -30 °C ● max. 55 °C connection method / header Design of electrical connection for the inputs and outputs M8, 3-pole Design of electrical connection for supply voltage M8, 4-pole ET-Connection ● ET-Connection M8, 4-pin, shielded Dimensions Width 30 mm Height 159 mm Depth 40 mm Weights Weight, approx. 145 g last modified: 3/7/2022 6ES71435BF000BA0 Page 3/3 7/9/2022 Subject to change without notice © Copyright Siemens