74VHC138MTR

74VHC138 3 TO 8 LINE DECODER (INVERTING) ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 5.7ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 4 µA (MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) POWER DOWN PROTECTION ON INPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 8 mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 2V to 5.5V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 138 IMPROVED LATCH-UP IMMUNITY DESCRIPTION The 74VHC138 is an advanced high-speed CMOS 3 TO 8 LINE DECODER (INVERTING) fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. If the device is enabled, 3 binary select (A, B, and C) determine which one of the outputs will go low. If enable input G1 is held low or either G2A or G2B is held high, the decoding function is inhibited and all the 8 outputs go to high. SOP TSSOP Table 1: Order Codes PACKAGE T&R SOP TSSOP 74VHC138MTR 74VHC138TTR Tree enable inputs are provided to ease cascade connection and application of address decoders for memory systems. Power down protection is provided on all inputs and 0 to 7V can be accepted on inputs with no regard to the supply voltage. This device can be used to interface 5V to 3V. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. Figure 1: Pin Connection And IEC Logic Symbols November 2004 Rev. 4 1/12 74VHC138 Figure 2: Input Equivalent Circuit Table 2: Pin Description PIN N° SYMBOL 1, 2, 3 4, 5 6 15, 14, 13, 12, 11, 10, 9, 7 8 16 A, B, C G2A, G2B G1 Y0 to Y7 GND VCC NAME AND FUNCTION Address Inputs Enable Inputs Enable Input Outputs Ground (0V) Positive Supply Voltage Table 3: Truth Table INPUTS OUTPUTS ENABLE SELECT G2B G2A G1 C B A Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 X X H L L L L L L L L X H X L L L L L L L L L X X H H H H H H H H X X X L L L L H H H H X X X L L H H L L H H X X X L H L H L H L H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L X : Don’t care Figure 3: Logic Diagram This logic diagram has not be used to estimate propagation delays 2/12 74VHC138 Table 4: Absolute Maximum Ratings Symbol VCC Parameter Supply Voltage VI DC Input Voltage VO DC Output Voltage IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Current ICC or IGND DC VCC or Ground Current Storage Temperature Tstg TL Lead Temperature (10 sec) Value Unit -0.5 to +7.0 V -0.5 to +7.0 V -0.5 to VCC + 0.5 - 20 V mA ± 20 mA ± 25 mA ± 75 mA -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied Table 5: Recommended Operating Conditions Symbol VCC Parameter Supply Voltage Value Unit 2 to 5.5 V VI Input Voltage 0 to 5.5 V VO Output Voltage 0 to VCC V Top Operating Temperature -55 to 125 °C 0 to 100 0 to 20 ns/V dt/dv Input Rise and Fall Time (note 1) (VCC = 3.3 ± 0.3V) (VCC = 5.0 ± 0.5V) 1) VIN from 30% to 70% of VCC 3/12 74VHC138 Table 6: DC Specifications Test Condition Symbol VIH VIL VOH VOL II ICC Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current Quiescent Supply Current Value TA = 25°C VCC (V) Min. 2.0 3.0 to 5.5 2.0 3.0 to 5.5 Typ. Max. -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 1.5 1.5 0.7VCC 0.7VCC 0.7VCC Max. V 0.5 0.5 0.5 0.3VCC 0.3VCC 0.3VCC 2.0 IO=-50 µA 1.9 2.0 1.9 1.9 3.0 IO=-50 µA 2.9 3.0 2.9 2.9 4.5 IO=-50 µA 4.4 4.5 3.0 IO=-4 mA 2.58 3.94 4.4 4.4 2.48 2.4 Unit V V 4.5 IO=-8 mA 2.0 IO=50 µA 0.0 0.1 0.1 0.1 3.0 IO=50 µA 0.0 0.1 0.1 0.1 4.5 IO=50 µA 0.0 0.1 0.1 0.1 3.0 IO=4 mA 0.36 0.44 0.55 4.5 IO=8 mA 0.36 0.44 0.55 0 to 5.5 VI = 5.5V or GND ± 0.1 ±1 ±1 µA 5.5 VI = VCC or GND 4 40 40 µA 3.8 3.7 V Table 7: AC Electrical Characteristics (Input tr = tf = 3ns) Test Condition Symbol tPLH tPHL Parameter Propagation Delay Time A, B, C, to Y VCC (V) CL (pF) 3.3(*) (*) (**) Propagation Delay Time G to Y Propagation Delay Time G2A, G2B to Y (*) Voltage range is 3.3V ± 0.3V (**) Voltage range is 5.0V ± 0.5V 4/12 -55 to 125°C Min. Max. Min. Max. 15 8.2 11.4 1.0 13.0 1.0 13.0 50 10.0 15.8 1.0 18.0 1.0 18.0 15 5.7 8.1 1.0 9.5 1.0 9.5 5.0(**) 50 7.2 10.1 1.0 11.5 1.0 11.5 3.3(*) 15 8.1 12.8 1.0 15.0 1.0 15.0 (*) 50 10.6 16.3 1.0 18.5 1.0 18.5 (**) 15 5.6 8.1 1.0 9.5 1.0 9.5 5.0(**) 50 7.1 10.1 1.0 11.5 1.0 11.5 3.3(*) 15 8.2 11.4 1.0 13.5 1.0 13.5 3.3(*) 50 10.7 14.9 1.0 17.0 1.0 17.0 5.0(**) 15 5.8 8.1 1.0 9.5 1.0 9.5 5.0(**) 50 7.3 10.1 1.0 11.5 1.0 11.5 3.3 3.3 Min. -40 to 85°C Max. 5.0 tPLH tPHL TA = 25°C Typ. 5.0 tPLH tPHL Value Unit ns ns ns 74VHC138 Table 8: Capacitive Characteristics Test Condition Symbol Parameter Value TA = 25°C Min. Typ. Max. 10 CIN Input Capacitance 6 CPD Power Dissipation Capacitance (note 1) 34 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC Figure 4: Test Circuit CL =15/50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) Figure 5: Waveform - Propagation Delays For Inverting Outputs (f=1MHz; 50% duty cycle) 5/12 74VHC138 Figure 6: Waveform - Propagation Delays For Non-inverting Outputs (f=1MHz; 50% duty cycle) 6/12 74VHC138 SO-16 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.25 a2 MAX. 0.004 0.010 1.64 0.063 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 10 0.385 0.393 E 5.8 6.2 0.228 0.244 e 1.27 e3 0.050 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) 0016020D 7/12 74VHC138 TSSOP16 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0079 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0˚ L 0.45 A 0.60 0.0256 BSC 8˚ 0˚ 0.75 0.018 8˚ 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 8/12 74VHC138 Tape & Reel SO-16 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 22.4 0.519 0.882 Ao 6.45 6.65 0.254 0.262 Bo 10.3 10.5 0.406 0.414 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 9/12 74VHC138 Tape & Reel TSSOP16 MECHANICAL DATA mm. inch DIM. MIN. A MAX. MIN. 330 13.2 TYP. MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 10/12 TYP 0.504 22.4 0.519 0.882 Ao 6.7 6.9 0.264 0.272 Bo 5.3 5.5 0.209 0.217 Ko 1.6 1.8 0.063 0.071 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 74VHC138 Table 9: Revision History Date Revision 12-Nov-2004 4 Description of Changes Order Codes Revision - pag. 1. 11/12 74VHC138 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 12/12