L9942
Integrated stepper motor driver for bipolar stepper motors
with microstepping and programmable current profile
Features
■
Two full bridges for max. 1.3 A load
(RDSON = 500 m)
■
Programmable current waveform with look-up
table: 9 entries with 5 bit resolution
■
Current regulation by integrated PWM
controller and internal current sensing
■
Programmable stepping mode: full, half, mini
and microstepping
■
Programmable slew rate for EMC and power
dissipation optimization
■
Programmable Fast-, Slow-, Mixed- and AutoDecay Mode
■
Full-scale current programmable with 3 bit
resolution
■
Programmable stall detection
■
Step clock input for reduced µController
requirements
■
Very low current consumption in standby mode
IS < 3 µA, typ. Tj 85 °C
■
All outputs short circuit protected with
openload, overload current, temperature
warning and thermal shutdown
■
The PWM signal of the internal PWM controller
is available as digital output.
■
All parameters are guaranteed for 3 V < Vcc <
5.3 V and for 7 V < Vs < 20 V
Applications
Stepper motor driver for bipolar stepper motors in
automotive applications like light levelling,
Bending light and Throttle control.
Table 1.
PowerSSO24
Description
The L9942 is an integrated stepper motor driver
for bipolar stepper motors with microstepping and
programmable current profile look-up-table to
allow a flexible adaptation of the stepper motor
characteristics and intended operating conditions.
It is possible to use different current profiles
depending on target criteria: audible noise,
vibrations, rotation speed or torque. The decay
mode used in PWM-current control circuit can be
programmed to slow-, fast-, mixed-and autodecay. In autodecay mode device will use slow
decay mode if the current for the next step will
increase and the fast decay or mixed decay mode
if the current will decrease. The programmable
stall detection is useful in case of head lamp
leveling and bending light application, by
preventing to run the motor too long time in stall
for position alignment. If a stall is detected, the
alignment process is closed and the noise is
minimized.
Device summary
Order code
Junction temp. range, C
Package
Packing
L9942XP1
-40 to 150
PowerSSO24
Tube
L9942XP1TR
-40 to 150
PowerSSO24
Tape and reel
September 2013
Doc ID 11778 Rev 7
1/40
www.st.com
1
Contents
L9942
Contents
1
Block diagram and pin information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2
Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3
4
2/40
2.1
Dual power supply: VS and VCC
2.2
Standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3
Diagnostic functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.4
Overvoltage and undervoltage detection . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.5
Temperature warning and thermal shutdown . . . . . . . . . . . . . . . . . . . . . . 10
2.6
Inductive loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.7
Cross-current protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.8
PWM current regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.9
Decay modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10
Overcurrent detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.11
Open load detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.12
Stepping modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.13
Decay modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
..........................................9
Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2
ESD protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.3
Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.4
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4.1
Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4.2
Over- and undervoltage detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.4.3
Reference current output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.4.4
Charge pump output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.4.5
Outputs: Qxn (x = A; B n = 1; 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.4.6
PWM control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Functional description of the logic with SPI . . . . . . . . . . . . . . . . . . . . . 21
4.1
Motor stepping clock input (STEP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2
PWM output (PWM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.3
Serial peripheral interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Doc ID 11778 Rev 7
L9942
5
6
7
Contents
4.4
Chip select not (CSN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.5
Serial data in (DI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.6
Serial data out (DO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.7
Serial clock (CLK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.8
Data register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SPI - control and status registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.1
Register 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.2
Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.3
Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.4
Register 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.5
Register 4 and 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.6
Register 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.7
Register 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.8
Auxiliary logic blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.8.1
Fault condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.8.2
SPI communication monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.8.3
PWM monitoring for stall detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Logic with SPI - electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . 28
6.1
Inputs: CSN, CLK, STEP, EN and DI . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.2
DI timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.3
Outputs: DO, PWM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.4
Output: DO timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.5
CSN timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.6
STEP timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.1
Stall detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.2
Step clock input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.3
Load current control and detection of overcurrent (shortages at outputs) 33
8
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
9
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Doc ID 11778 Rev 7
3/40
List of tables
L9942
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
Table 26.
Table 27.
4/40
Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Truth table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ESD protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Operating junction temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Temperature warning and thermal shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Over- and undervoltage detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Reference current output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Charge pump output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Outputs: Qxn (x = A; B n =1; 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
PWM control (see Figure 4 and Figure 7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Register 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Register 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Register 4 and 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Register 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Register 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Inputs: CSN, CLK, STEP, EN and DI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
DI timing (see Figure 11 and Figure 13) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Outputs: DO, PWM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Output: DO timing (see Figure 12 and Figure 13) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CSN timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
STEP timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Doc ID 11778 Rev 7
L9942
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin connection (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Stepping modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Decay modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Thermal data of the package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
VS monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Logic to set load current limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Switching on minimum time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SPI and registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Transfer timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Input timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
SPI - DO valid data delay time and valid time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
DO enable and disable time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Timing of status bit 0 (fault condition) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Stall detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Reference generation for PWM control (switch on) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Reference generation for PWM control (decay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
PowerSSO24 mechanical data and package dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 38
Doc ID 11778 Rev 7
5/40
Block diagram and pin information
1
L9942
Block diagram and pin information
Figure 1.
Block diagram
VBAT
ReversePolarityProtection
VCC
CP
Charge
Pump
Oscillator
STEP
QA1
Diagnostic
SPI + Register + Logic
Phase Counter+Current Profile
⇓
PWM Current DAC
EN
PWM
μC
VS
DO
DI
CLK
CSN
Gate-Driver
&
PWM-Controller
Note: value of capacitor has
to be choosen carefully to
limit the VS voltage below
absolute maximum ratings in
case of an unexpected
freewheeling condition (e.g.
TSD, POR)
QA2
Stepper
Motor
QB1
Gate-Driver
&
PWM-Controller
Diagnostic
QB2
U/IConverter
Biasing
GND
RREF
GNDP
GND
Figure 2.
Pin connection (top view)
PGND
1
Power SSO24
23 QA2
QA1 2
VS 3
22 VS
CLK 4
21 EN
20 RREF
DI 5
CSN 6
DO 7
Exposed
Pad
19 VCC
18 TEST
PWM 8
17 GND
STEP 9
16 CP
VS 10
15 VS
14 QB2
QB1 11
13 PGND
PGND 12
All pins with the same name must be externally connected!
All pins PGND are internally connected to the heat slug.
6/40
24 PGND
Doc ID 11778 Rev 7
L9942
Block diagram and pin information
Table 2.
Pin description
Pin
Symbol
1, 12, 13,
24
PGND
3, 10, 15,
22
VS
Function
Power ground: All pins PGND are internally connected to the heat slug.
Important: All pins of PGND must be externally connected!
Power supply voltage (external reverse protection required): For EMI
reason a ceramic capacitor as close as possible to PGND is recommended.
Important: All pins of VS must be externally connected!
2, 23
Fullbridge-outputs An: The output is built by a high-side and a low-side
switch, which are internally connected. The output stage of both switches is
QA1,QA
a power DMOS transistor. Each driver has an internal reverse diode (bulk2
drain-diode: highside driver from output to VS, low-side driver from PGND to
output). This output is overcurrent protected.
11, 14
Fullbridge-outputs Bn: The output is built by a highside and a low-side
switch, which are internally connected. The output stage of both switches is
QB1,QB
a power DMOS transistor. Each driver has an internal reverse diode (bulk2
drain-diode: highside driver from output to VS, low-side driver from PGND to
output). This output is overcurrent protected.
CLK
SPI clock input: The input requires CMOS logic levels. The CLK input has
a pull-down current. It controls the internal shift register of the SPI.
5
DI
Serial data input: The input requires CMOS logic levels. The DI input has a
pull-down current. It receives serial data from the microcontroller. The data
is a 16bit control word and the most significant bit (MSB, bit 0) is transferred
first.
6
CSN
7
DO
SPI data output: The diagnosis data is available via the SPI and it is a
tristate-output. The output is CMOS compatible will remain highly resistive,
if the chip is not selected by the input CSN (CSN = high)
PWM
PWM output This CMOS compatible output reflects the current duty cycle
of the internal PWM controller of bridge A. It is an high resistance output
until VCC has reached minimum voltage ore can switched off via the SPI
command.
9
STEP
Step clock input: The input requires CMOS logic levels. The STEP input
has a pull-down current. It is clock of up and down counter of control
register 0. Rising edge starts new PWM cycle to drive motor in next
position.
16
CP
17
GND
Ground: Reference potential besides power ground e.g. for reference
resistor RREF. From this pin exist a resistive path via substrate to PGND.
18
TEST
Test input The TEST input has a pull-down current. Pin used for production
test only. In the application it must be connected to GND.
19
VCC
Logic supply voltage: For this input a ceramic capacitor as close as
possible to GND is recommended.
4
8
Chip Select Not input The input requires CMOS logic levels. The CSN
input has a pull-up current. The serial data transfer between device and
micro controller is enabled by pulling the input CSN to low level.
Charge Pump Output: A ceramic capacitor (e.g.100 nF) to VS can be
connected to this pin to buffer the charge-pump voltage.
Doc ID 11778 Rev 7
7/40
Block diagram and pin information
Table 2.
Pin
20
21
8/40
L9942
Pin description (continued)
Symbol
RREF
EN
Function
Reference Resistor The reference resistor is used to generate a
temperature stable reference current used for current control and internal
oscillator. At this output a voltage of about 1.28V is present. The resistor
should be chosen that a current of about 200uA will flow through the
resistor.
Enable input: The input requires CMOS logic levels. The EN input has a
pull-down resistor. In standby-mode outputs will be switched off and all
registers will be cleared. If EN is set to a logic high level then the device will
enter the active mode.
Doc ID 11778 Rev 7
L9942
Device description
2
Device description
2.1
Dual power supply: VS and VCC
The power supply voltage VS supplies the half bridges. An internal charge-pump is used to
drive the highside switches. The logic supply voltage VCC (stabilized) is used for the logic
part and the SPI of the device. Due to the independent logic supply voltage the control and
status information will not be lost, if there are temporary spikes or glitches on the power
supply voltage. In case of power-on (VCC increases from undervoltage to VPOR OFF = 2.60 V,
typical) the circuit is initialized by an internally generated power-on-reset (POR). If the
voltage VCC decreases under the minimum threshold (VPOR ON = 2.3 V, typical), the outputs
are switched to tristate (high impedance) and the internal registers are cleared.
2.2
Standby mode
The EN input has a pull-down resistor. The device is in standby mode if EN input isn't set to
a logic high level. All latched data will be cleared and the inputs and outputs are switched to
high impedance. In the standby mode the current at VS (VCC) is less than 3 µA (1 µA) for
CSN = high (DO in tristate). If EN is set to a logic high level then the device will enter the
active mode. In the active mode the charge pump and the supervisor functions are
activated.
2.3
Diagnostic functions
All diagnostic functions (overload/-current, open load, power supply over-/undervoltage,
temperature warning and thermal shutdown) are internally filtered (tGL = 32 µs, typical) and
the condition has to be valid for a minimum time before the corresponding status bit in the
status registers will be set. The filters are used to improve the noise immunity of the device.
Open load and temperature warning function are intended for information purpose and will
not change the state of the bridge drivers. On contrary, the overload/-current and thermal
shutdown condition will disable the corresponding driver (overload/-current) or all drivers
(thermal shutdown), respectively. The microcontroller has to clear the status bit to reactivate
the bridge driver.
2.4
Overvoltage and undervoltage detection
If the power supply voltage Vs rises above the overvoltage threshold VSOV OFF (typical
21 V), an overvoltage condition is detected. Programmable by SPI (OVW) the outputs are
switched to high impedance state (default after reset) or the overvoltage bit is set without
switching the outputs to high impedance. When the voltage Vs drops below the undervoltage threshold VSUV OFF, the outputs are switched to high impedance state to avoid the
operation of the power devices without sufficient gate driving voltage (increased power
dissipation). Error condition is latched and the microcontroller needs to clear the status bits
to reactivate the drivers.
Doc ID 11778 Rev 7
9/40
Device description
2.5
L9942
Temperature warning and thermal shutdown
If junction temperature rises above Tj TW a temperature warning flag is set which is
detectable via the SPI. If junction temperature increases above the second threshold Tj SD,
the thermal shutdown bit will be set and power DMOS transistors of all output stages are
switched off to protect the device. In order to reactivate the output stages the junction
temperature must decrease below Tj SD -Tj SD HYS and the thermal shutdown bit has to be
cleared by the microcontroller.
2.6
Inductive loads
Each half bridge is built by an internally connected highside and a low-side power DMOS
transistor. Due to the built-in reverse diodes of the output transistors, inductive loads can be
driven without external free-wheeling diodes. In order to reduce the power dissipation during
free-wheeling condition the PWM controller will switch-on the output transistor parallel to the
freewheeling diode (synchronous rectification).
2.7
Cross-current protection
The four half-brides of the device are cross-current protected by an internal delay time
depending on the programmed slew rate. If one driver (LS or HS) is turned-off then
activation of the other driver of the same half bridge will be automatically delayed by the
cross-current protection time.
2.8
PWM current regulation
An internal current monitor output of each high-side and low-side transistor sources a
current image which has a fixed ratio of the instantaneous load current. This current images
are compared with the current limit in PWM control. Range of limit can reach from
programmed full scale value (register1 DAC Scale) down belonging LSB value of 5 bit DAC
(register1 DAC Phase x). The data of the two 5 bit DACs comes form set up in 9 current
profiles (register2 to 6). If signal changes to logic high at pin STEP then 2 current profiles
are moved in register1 for DAC Phase A and B. Number of profile depends on phase
counter reading and direction bit in register0 (Figure 7). The bridges are switched on until
the load current sensed at HS switch exceeds the limit. Load current comparator signal is
used to detect open load or overcurrent condition also.
2.9
Decay modes
During off-time the device will use one of several decay modes programmable by SPI
(Figure 4 top). In slow decay mode HS switches are activated after cross current protection
time for synchronous rectification to reduce the power dissipation (Figure 4 detail A). In fast
decay opposite half bridge will switched on after cross current protection time, that is same
like change in the direction. For mixed decay the duration of fast decay period before slow
decay can be set to a fixed time (Figure 4 detail B continuous line) or is triggered by underrun of the load current limit (Figure 4 detail B dashed line), that can be detected at LS
switch. The special mode where the actual phase counter value is taken into account to
select the decay mode is called auto decay (e.g. in Figure 3 Micro Stepping DIR=1). If the
absolute value of the current limit is higher as during step before then PWM control uses
10/40
Doc ID 11778 Rev 7
L9942
Device description
slow decay mode always. Otherwise one of the fast decay modes is automatic selected for a
quick decrease of the load current and so it obtains new lower target value.
2.10
Overcurrent detection
The overcurrent detection circuit monitors the load current in each activated output stage. In
HS stage it is in function after detection of current limit during PWM cycle and in LS stage it
works permanently. If the load current exceeds the overcurrent detection threshold for at
least tISC = 4 µs, the overcurrent flag is set and the corresponding driver is switched off to
reduce the power dissipation and to protect the integrated circuit. Error condition is latched
and the microcontroller needs to clear the status bits to reactivate the drivers.
2.11
Open load detection
The open load detection monitors the activity time of the PWM controller and is available for
each phase. If the limit of load current is below around 100mA then open load condition is
detectable. Open load bit for a bridge is set in the register6 if this low current limit can't
reached after at least 15 consecutive PWM cycles.
Table 3.
Truth table
DC2
DC1
DC0
I4
I3
I2
I1
I0
max. IOL
0
0
0
0
x
x
x
x
46mA
0
0
1
0
x
x
x
x
68mA
0
1
0
0
0
x
x
x
52mA
0
1
1
0
0
x
x
x
81mA
1
0
0
0
0
0
x
x
53mA
1
0
1
0
0
0
x
x
78mA
1
1
0
0
0
0
0
1
37mA
1
1
1
0
0
0
0
1
44mA
Truth table shows possible profiles for active open load detection. Maximum threshold IOL is
shown in left column if x bits are 1 (see also Figure 7). Lowest possible limit is e.g. 3.1 mA
for DC2=DC1=DC0=0 and it is set only I0=1.
2.12
Stepping modes
One full revolution can consist of four full steps, eight half steps, sixteen mini steps or 32
microsteps.
Mode is set up in register 0 and it defines increment size of phase counter. Phase counter
value defines address of corresponding current profile. Stepping modes with typical profile
values can see in Figure 3 (e.g. also so called 'Two Phase On' shown in dashed line).
Doc ID 11778 Rev 7
11/40
Device description
Figure 3.
L9942
Stepping modes
Full-Stepping Mode: DIR=0
0
8
Full-Stepping Mode: DIR=1
16
Phase Counter
24
24
16
8
0
0
Current Driver A
Current Driver A
0
8
Address of Current
Profile Entry
8
0
8
0
8
Current Driver B
Current Driver B
8
0
8
Address of Current
Profile Entry
0
8
0
8
STEP Signal
STEP Signal
Half-Stepping Mode: DIR=0
0
4
8
12
16
20
Half-Stepping Mode: DIR=1
24
Phase Counter
28
0
28
24
20
Current Driver A
0
4
8
8
4
0
4
0
8
4
8
4
Address of Current
Profile Entry
0
4
8
4
0
4
Address of Current
Profile Entry
8
4
0
4
4
6
8
10
12
14
16
18
20
22
24
2
4
6
8
6
8
6
4
2
0
2
4
2
0
6
8
28
30
Phase Counter
0
30
28
26
2
4
24
22
6
8
6
4
2
Adress of Current
Profile Entry
0
2
4
6
8
6
6
4
2
0
2
4
6
Adress of Current
Profile Entry
8
6
4
2
0
2
8
4
0
4
20
18
16
14
12
10
8
6
4
2
Slow Decay
Mode
Mixed Decay
Mode
0
2
4
6
8
6
4
2
4
6
8
6
4
2
0
2
4
6
0 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Slow Decay
Mode
Adress of Current
Profile Entry
Slow Decay
Mode
Adress of Current
Profile Entry
Mixed Decay
Mode
0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1
Slow Decay
Mode
Mixed Decay
Mode
8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7
Mixed Decay
Mode
2
Current Driver A
Mixed Decay
Mode
0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1
Current Driver B
4
Micro Stepping Mode: DIR=1 (e.g. auto decay)
Phase Counter
Current Driver A
12/40
4
STEP Signal
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Slow Decay
Mode
8
Current Driver B
Micro Stepping Mode: DIR=0 (e.g auto decay)
Mixed Decay
Mode
4
Current Driver A
STEP Signal
Slow Decay
Mode
0
4
Current Driver B
4
4
Mini-Stepping Mode: DIR=1
26
Current Driver A
0
8
STEP Signal
Mini-Stepping Mode: DIR=0
2
12
Driver Current B
STEP Signal
0
16
Driver Current A
Current Driver B
4
0
Current Driver B
Mixed Decay
Mode
Slow Decay
Mode
8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7
Doc ID 11778 Rev 7
Slow Decay
Mode
Mixed Decay
Mode
L9942
Device description
2.13
Decay modes
Figure 4.
Decay modes
Load
Current
ON
SLOW
DECAY
FAST
DECAY
MIXED
DECAY
VS
VS
on
on
A
VS
on
on
on
on
B
VS
VS
on
on
on
Time
Internal PWM_CLK
Detail A: SWITCH ON AND SLOW DECAY
Step
Limit
HS
ON
TB
TCC
TFT
TCC
TB
register0
DM2 DM1 DM0
0
0
0
TCC SLOW DECAY
T FT
fast decay
fast decay
Load
Current
MODE
slow
VS
Time
Fast decay is caused by
current through internal
diodes during cross current
protection time.
OFF
OFF
OFF
OFF
Filter time for the purpose of switch off delay in on mode is set by FT register6
Cross current protection time is set by SR1 SR0 register0
Blank time of load current comparator TB=TCC
Detail B:
MIXED DECAY
register0
DM2 DM1 DM0 MODE CURVE
X
X
X
Load
Current
TCC
Step
Limit
LS
TFT
FAST
DECAY
Tmc
0
1
1
1
0
1
T MD1
T MD2
T mc
Load
Current
TCC
SLOW DECAY
after current
undershoot
>
T mc = T FT + 2TCC
SLOW DECAY
FAST with delay
DECAY
TCC
T MDx= TMD1
or T MD2
T MDx
TCC
Time
TFT Filter time for purpose of delay when decay mode has to change after limit under-run
TMD When limit is reached so fast decay duration time is set by DM1 DM2 register0
Doc ID 11778 Rev 7
Time
13/40
Electrical specifications
L9942
3
Electrical specifications
3.1
Absolute maximum ratings
Table 4.
Absolute maximum ratings
Symbol
VS
VCC
Parameter
DC supply voltage
single pulse tmax < 400 ms
Stabilized supply voltage, logic supply
VDI,VDO,
Digital input / output voltage
VCLK VCSN,
VSTEP VEN
VRREF
Current reference resistor
-0.3 to 28
V
40
V
-0.3 to 5.5
V
-0.3 to VCC + 0.3
V
-0.3 to VCC + 0.3
V
Charge pump output
-0.3 to VS + 11
V
VQxn
(x=A;B n=1;2) output voltage
-0.3 to VS + 0.3
V
IQxn
(x=A;B n=1;2) output current
2.5
A
Leaving the limitation of any of these values may cause an
irreversible damage of the integrated circuit!
ESD protection
Table 5.
ESD protection
Parameter
Value
Unit
All pins
2 (1)
kV
output pins: Qxn (x=A;B n=1;2)
4(2)
kV
1. HBM according to MIL 883C, Method 3015.7 or EIA/JESD22-A114-A
2. HBM with all unzapped pins grounded
14/40
Unit
VCP
Warning:
3.2
Value
Doc ID 11778 Rev 7
L9942
3.3
Electrical specifications
Thermal data
Table 6.
Symbol
Tj
Table 7.
Symbol
Operating junction temperature
Parameter
Operating junction temperature
Value
Unit
-40 to 150
°C
Temperature warning and thermal shutdown
Parameter
Min.
Typ.
Max.
Unit
-
-
150
°C
TjTW ON
Temperature warning
threshold junction
temperature
Tj increasing
TjTW OFF
Temperature warning
threshold junction
temperature
-
130
-
-
°C
TjSD ON
Thermal shutdown threshold
junction temperature
-
-
-
170
°C
TjSD OFF
Thermal shutdown threshold
junction temperature
-
150
-
-
°C
TjSD HYS
Thermal shutdown hysteresis
-
-
5
-
K
Figure 5.
Thermal data of the package
Note:
1s
1 signal layer
2s2p 2 signal layers 2 internal planes
Doc ID 11778 Rev 7
15/40
Electrical specifications
3.4
L9942
Electrical characteristics
VS = 7 to 20 V, VCC = 3.0 to 5.3 V, Tj = -40 to 150 °C, IREF = -200 µA, unless otherwise
specified. The voltages are referred to GND and currents are assumed positive, when the
current flows into the pin.
3.4.1
Supply
Table 8.
Supply
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
-
7
20
mA
-
3
10
-
6
20
VCC = 5.0 V EN=VCC,
DI=CLK=STEP=0V
-
1
3
mA
VCC = 5.0 V TEST;
EN = 0 V; CSN =
VCC no clocks
outputs floating
-
1
3
µA
Tj = 125 °C
-
2
6
µA
Tj = -40 °C
-
4
13
VS DC supply current in active VS = 13.5 V, EN=VCC outputs
mode
floating
IS
VS quiescent supply current
ICC
ICC
VCC DC supply current in
active mode
VCC quiescent supply current
VS = 13.5 V, TEST,
EN = 0V outputs
floating
CSN=VCC no
clocks outputs
floating
VS = 13.5 V, VCC =
5.0 V
IS + ICC
tsetPOR (1)
TEST; EN=0 V
CSN=VCC no
Sum quiescent supply current
clocks outputs
floating
VCC on set up time
Tj = -40 °C
to 25 °C
Tj = 125 °C
Tj = -40 °C
to 25 °C
to 25 °C
µA
Tj = 125 °C
-
8
26
EN = 5 V, CSN=CLK=0V DO
changes from high ohmic to logic
level LOW
2
-
-
1. This parameter is guaranteed by design.
16/40
µA
Doc ID 11778 Rev 7
µs
L9942
Electrical specifications
3.4.2
Over- and undervoltage detection
Table 9.
Over- and undervoltage detection
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
VSUV ON
VS UV-threshold voltage
VS increasing
-
-
6.90
V
VSUV OFF
VS UV-threshold voltage
VS decreasing
4.8
-
-
V
VSUV hyst
VS UV-hysteresis
VSUV ON -VSUV OFF
-
0.3
-
V
VSOV OFF
VS OV-threshold voltage
VS increasing
-
21
25
V
VSOV ON
VS OV-threshold voltage
VS decreasing
18.5
20
-
V
VSOV hyst
VS OV-hysteresis
VSOV OFF -VSOV ON
-
0.5
-
V
VPOR OFF
Power-off-reset threshold
VCC increasing
-
2.6
2.9
V
VPOR ON
Power-on-reset threshold
VCC decreasing
2.00
2.3
-
V
VPOR hyst
Power-on-reset hysteresis
VPOR OFF -VPOR ON
-
0.11
-
V
Figure 6.
VS monitoring
Register 7
OV
Register 7
UV
1
1
0
0
VSUV OFF
VSOV ON
VSUV ON
3.4.3
Reference current output
Table 10.
Reference current output
Symbol
VREF
IREFshorted
IREFopen
VS
VS
Parameter
Reference voltage range
Test condition
IREF = -200 A
Reference current
register6 bit7 RERR = 1
threshold shorted pin REF
Reference current
threshold open pin REF
register6 bit7 RERR = 1
VSOV OFF
Min.
Typ.
Max.
Unit
1.05
1.25
1.45
V
-
-
-250
A
-150
-
-
A
The device works properly without the external resistor at pin REF. In this case it doesn't
have to fulfill all specified parameters.
Doc ID 11778 Rev 7
17/40
Electrical specifications
L9942
3.4.4
Charge pump output
Table 11.
Charge pump output
Symbol
Parameter
Test condition
VS=7 V
VCP
Charge pump output voltage
VS=13.5 V
VS=20 V
ICP= -100 A, all
switches off at
Qxn
Min.
Typ.
Max.
Unit
11
-
20
V
20
-
35
V
30
-
40
V
The ripple of voltage at CP can suppressed using a capacity of e.g.100 nF.
3.4.5
Outputs: Qxn (x = A; B n = 1; 2)
The comparator, which is monitoring current image of HS, is working during ON cycle of
PWM control. If load current is higher as set value then the signal ILIMIT is generated and
after filter time the bridge is switched off. Test mode gets access to signal ILIMIT and
threshold of current can be measured.
Table 12.
Symbol
Outputs: Qxn (x = A; B n =1; 2)
Parameter
RDSON HS On-resistance Qxn to VS
RDSON LS
|IQxnOC |
On-resistance Qxn to
PGND
Test condition
Min.
Typ.
Max.
Unit
VS = 13.5 V, Tj = 25 °C,
IQxn = -1.0 A
-
500
700
m
VS = 13.5 V, Tj = 125 °C,
IQxn = -1.0 A
-
750
1000
m
VS = 7.0 V, Tj = 25 °C,
IQxn = -1.0 A
-
550
750
m
VS = 13.5 V, Tj = 25 °C,
IQxn = + 1.0 A
-
500
700
m
VS = 13.5 V, Tj = 125 °C,
IQxn = + 1.0 A
-
750
1000
m
VS = 7.0 V, Tj = 25 °C,
IQxn = + 1.0 A
-
550
750
m
1.6
2
-
A
Output overcurrent
test mode exclusive of filter
limitation to VS or PGND time 4µs (Chapter 2.10)
Bits: DC2 DC1 DC0=000
60
95
130
Bits: DC2 DC1 DC0=001
100
140
180
Bits: DC2 DC1 DC0=010
Value of output current to
Bits: DC2 DC1 DC0=011
supply VS (so called full
IQxnFS_HS
scale value)1 sourcing
Bits: DC2 DC1 DC0=100
from HS switch
Bits: DC2 DC1 DC0=101
180
230
280
300
360
420
485
550
615
720
810
900
Bits: DC2 DC1 DC0=110
1000
1150
1300
Bits: DC2 DC1 DC0=111
1200
1350
1500
-
MIN(1)
-
MAX(1)
IQxnLIM_HS
Accuracy of micro steps
current limit
1. MIN= 0.92 · IQxnLIM – 0.02 · |IQxnFS_HS |; MAX= 1.08 · IQxnLIM + 0.02 · |IQxnFS_HS |
18/40
Doc ID 11778 Rev 7
mA
mA
L9942
Electrical specifications
Note:
Current profile has to pre set with I4 I3 I2 I1 I0 = 11111 and load to register 1.
Output current limit IQxnLIM is product of full scale current |IQxnFS_ | (bits DC2 DC1 DC0) and
value of DAC Phase A/B (bits I4 I3 I2 I1 I0) in register1.
Values of DAC Phase A and B can read out and depends on set up done before:
Figure 7.
1.
direction DIR, stepping mode ST1 ST0 and phase counter P4 P3 P2 P1 P0 in register 0 and
2.
value of corresponding current profile (for address of current profile entry see also
Figure 3).
Logic to set load current limit
Register 0
UP/Down
Count by
1,2,4,8
PhaseCounter
P4
P3
P2
Decay Mode
P1
DM2
P0
DM1
DM0
Slew Rate
StepMode
SR1
ST1 ST0
SR0
DIR
STEP
0
0
0
0 1 2 3 0 1 2 3 0 1 2 3
A2 A1 A0
MUX
A3
A2
MUX
A1
MUX
A0
Address Calculation
Phase A
Adr
A3=0
A[3..0]
Adr
Phase B
A3=1
neg(A[3..0])
Adr
Current-Profile Table
stored in register2, ...6
5
9
I4
I4
I3
I3
I2
I2
I1
I1
A3=1
Adr A[3..0]
A3=0
neg(A[3..0])
I0
I0
Profile 8
Profile 7
I4
I3
I2
I1
I0
Profile 6
I4
I3
I2
I1
I0
Profile 5
I4
I3
I2
I1
I0
Profile 4
I4
I3
I2
I1
I0
Profile 3
I4
I3
I2
I1
I0
Profile 2
I4
I3
I2
I1
I0
Profile 1
I4
I3
I2
I1
I0
Profile 0
Register 1
5
5
DAC Phase A
DAC Phase B
DAC Scale
DI
DC2 DC1 DC0 I4
I3
I2
I1
I0
I4
I3
I2
I1
I0
QA1
5
5 bit DAC
Phase B
5
5
REF
I REF
DAC
Full Scale
LIMIT B
5 bit DAC
Phase A
I LIMIT A
I QA1LIM
1000
I Qx1LIM
QA2
I MAX
I QB1LIM
1000
5
5
QB1
5
IQA2LIM
1000
I Qx2LIM
5
QB2
IQB2LIM
1000
Doc ID 11778 Rev 7
19/40
Electrical specifications
L9942
3.4.6
PWM control
Table 13.
PWM control (see Figure 4 and Figure 7)
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
Bit: FRE= 1
-
20.8
-
kHz
Bit: FRE= 0
-
31.3
-
kHz
Bits: DM1 DM0= 0 1
-
4
-
µs
Bits: DM1 DM0= 1 0
-
8
-
µs
Bit: FILTER= 0
-
1.5
-
µs
Bit: FILTER= 1
-
2.5
-
µs
Bits: SR1 SR0= 0 0
-
0.5
-
µs
Cross current protection time Blank Bits: SR1 SR0= 0 1
time of comparator
Bits: SR1 SR0= 1 0
-
1
-
µs
-
2
-
µs
Bits: SR1 SR0= 1 1
-
4
-
µs
Bits: SR1 SR0= 0 0
-
13
-
V/µs
Slew rate (dV/dt 30 % - 70 %) @HS Bits: SR1 SR0= 0 1
switches on resistive load of 10 ,
Bits: SR1 SR0= 1 0
VS = 13.5 V
-
13
-
V/µs
-
6
-
V/µs
Bits: SR1 SR0= 1 1
-
6
-
V/µs
fPWM (1) Frequency of PWM cycles
TMD(1)
Mixed decay switch off delay time
TFT(1)
Glitch filter delay time
Tcc (1)
TB (1)
VSR
1. This parameter is guaranteed by design.
Time base is an internal trimmed oscillator of typical 2MHz and it has an accuracy of ±6 %.
Figure 8.
Switching on minimum time
Load current
at Qxn
T FT Filter time of current comparator
T FT
TCC
T
CC
Cross current protection time
T B Blank time of current comparator
Step limit
e.g. T B = TCC = 1 us
T CC
TB
Time
Internal PWM
clock
20 or 30 kHz
TPWM
on
decay
TINT _2MHz
Pin PWM
(for bridge A)
20/40
Doc ID 11778 Rev 7
T FT = 1.5 us
L9942
Functional description of the logic with SPI
4
Functional description of the logic with SPI
4.1
Motor stepping clock input (STEP)
Rising edge of signal STEP is latched. It is synchronized by internal clock. At next start of a
new PWM cycle the new values of output current limit are used to drive motor in next
position. Before start new motor step this signal has to be low for at least two internal clock
periods to reset latch.
4.2
PWM output (PWM)
This output reflects the current duty cycle of the internal PWM controller of bridge A. High
level indicates on state to increase current through load and low level is in off state so load
current decreases depending on chosen decay mode.
4.3
Serial peripheral interface (SPI)
This device uses a standard 16 bit SPI to communicate with a microcontroller. The SPI can
be driven by a microcontroller with its SPI peripheral running in following mode: CPOL = 0
and CPHA = 0.
For this mode, input data is sampled by the low to high transition of the clock CLK, and
output data is changed from the high to low transition of CLK.
A fault condition can be detected by setting CSN to low. If CSN = 0, the DO-pin will reflect an
internal error flag of the device which is a logical-or of all status bits in the Status Register
(reg 7) and in the current profile register 4 (reg 6). The microcontroller can poll the status of
the device without the need of a full SPI-communication cycle.
4.4
Chip select not (CSN)
The input pin is used to select the serial interface of this device. When CSN is high, the
output pin (DO) will be in high impedance state. A low signal will activate the output driver
and a serial communication can be started. The state when CSN is going low until the rising
edge of CSN will be called a communication frame.
4.5
Serial data in (DI)
The input pin is used to transfer data serial into the device. The data applied to the DI will be
sampled at the rising edge of the CLK signal and latched into an internal 16 bit shift register.
The first 3 bit are interpreted as address of the data register. At the rising edge of the CSN
signal the contents of the shift register will be transferred to the selected data register. The
writing to the register is only enabled if exactly 16 bits are transmitted within one
communication frame (i.e. CSN low). If more or less clock pulses are counted within one
frame the complete frame will be ignored. This safety function is implemented to avoid an
activation of the output stages by a wrong communication frame.
Doc ID 11778 Rev 7
21/40
Functional description of the logic with SPI
L9942
Note:
Due to this safety functionality a daisy chaining of SPI is not possible. Instead, a parallel
operation of the SPI bus by controlling the CSN signal of the connected ICs is
recommended.
4.6
Serial data out (DO)
The data output driver is activated by a logical low level at the CSN input and will go from
high impedance to a low or high level depending on the status bit 0 (fault condition). The first
rising edge of the CLK input after a high to low transition of the CSN pin will transfer the
content of the selected status register into the data out shift register. Each subsequent
falling edge of the CLK will shift the next bit out.
4.7
Serial clock (CLK)
The CLK input is used to synchronize the input and output serial bit streams. The data input
(DI) is sampled at the rising edge of the CLK and the data output (DO) will change with the
falling edge of the CLK signal.
4.8
Data register
The device has eight data registers. The first three bits (bit 0 ... bit 2) at the DI-input are used
to select one of the input registers. All bits are first shifted into an input shift register. After
the rising edge of CSN the contents of the input shift register will be written to the selected
Input Data Register only if a frame of exact 16 data bits are detected. The selected register
will be transferred to DO during the current communication frame.
Figure 9.
SPI and registers
DI
CLK
D
CLK_ADR
CSN
INT_2MHz
POR
SPIControll
DO
D0
D A0
D1
D2
A1
D3
D4
D5
D6
D7
D8
D9
D10
D11 D12
A0
A2
SEL_ERROR
SPI2REG
Phase Counter
Register 0
P4
P3
P2
Decay Mode
P1
P0
DM2
DM1
DM0
Slew Rate
Step Mode
SR1
ST1
SR0
ST0
DIR
Read Only
DAC_Scale
Register 1
DC2
Register 2
I4
Current Profile 1
I3
I2
I1
I0
I4
Current Profile 3
I3
I2
I1
I0
Register 3
DC1 DC0
BI4
BI3
DAC Phase B
BI2
BI1
OV
I4
I3
Register 5
I4
I3
Register 6
I2
I1
CLR6
SST
FT
I1
PWM
Freq
Test only
T1
T0
D1
D0
NPWM
I0
D4
I0
D7
D3
D2
ST
D5
Read-Only
Openload
RREF
Error Phase Phase
B
A
AI0
Current Profile 0
I3
I2
I1
I0
I4
Current Profile 2
I3
I2
I1
I0
I4
Current Profile 4
I3
I2
I1
I0
I4
Current Profile 6
I3
I2
I1
I0
I4
Current Profile 8
I3
I2
I1
I0
PWM Counter
D6
DAC Phase A
AI3
AI2
AI1
I4
PWM Counter
Current Profile 7
I2
AI4
PWM Counter PWM
Current Profile 5
Register 4
OVW
BI0
Read-Only
Register 7
22/40
Temperature
CLR7
TSD
TW
VS Monitor
OV(W)
UV HSB2 HSB1 LSB2
Doc ID 11778 Rev 7
Overcurrent
LSB1 HSA2 HSA1 LSA2
LSA1
A1
A2
L9942
SPI - control and status registers
5
SPI - control and status registers
5.1
Register 0
Table 14.
Register 0
Phase counter
Decay mode
Slew rate
Step mode
DIR
Bit
12
11
10
9
8
7
6
5
4
3
2
1
0
Access
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
P4
P3
P2
P1
P0
DM2
DM1
DM0
SR1
SR0
ST1
ST0
DIR
The meaning of the different bits is as follows:
:
DIR
ST1 ST0
This bit controls direction of motor movement. DIR=1 clockwise DIR=0 counter clockwise.
This bits controls step mode of motor movement (Figure 3).
00
Micro-stepping
01
Mini-stepping
10
Half-stepping
11
Full-stepping
SR1 SR0
DM2 DM1 DM0
This bit controls slew rate of bridge switches. See also parameter Table 13
This bits controls decay mode of output current (Figure 3).
000
Slow decay
001
Mixed decay, fast decay until TMD > 4 µs
010
Mixed decay, fast decay until TMD > 8 µs
011
Mixed decay, fast decay until current undershoot Tmc =TFT +TCC
100
Auto decay, fast decay without delay time
101
Auto decay, fast decay until TMD > 4 µs
110
Auto decay, fast decay until TMD > 8 µs
111
Auto decay, fast decay until current
undershoot Tmc
P4 P3 P2 P1 P0
Auto decay uses mixed decay automatically
to reduce current for next step if required
(see Figure 3 down right).
This bits control position of motor, e.g. 00000 step angle is 0°, 01111 step angle is 180 °.
Doc ID 11778 Rev 7
23/40
SPI - control and status registers
5.2
Register 1
Table 15.
Register 1
L9942
DAC scale
DAC phase B
DAC phase A
Bit
12
11
10
9
8
7
6
5
4
3
2
1
0
Access
rw
rw
rw
r
r
r
r
r
r
r
r
r
r
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
DC2
DC1
DC0
BI4
BI3
BI2
BI1
BI0
AI4
AI3
AI2
AI1
AI0
The meaning of the different bits is as follows:
These bits control DAC of
bridge A.
AI4 AI3 AI2 AI1 AI0
Value depends on address and the value of corresponding
current profile.
BI4 BI3 BI2 BI1 BI0
These bits control DAC of
bridge B.
DC2 DC1 DC0
These bits set full scale range
of limit, e.g. 000 for 100 mA or
111 for e.g. 1500 mA
5.3
Register 2
Table 16.
Register 2
Current profile 1
See also parameter Table 12.
OV
Test only
Current profile 0
Bit
12
11
10
9
8
7
6
5
4
3
2
1
0
Access
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
I4
I3
I2
I1
I0
OVW
T1
T0
I4
I3
I2
I1
I0
The meaning of the different bits is as follows:
:
I4 I3 I2 I1 I0
T1 T0
These bits are loaded in register1 DAC Phase A or B if needed. See also parameter Table 12
Should be programmed to 0.
-
OVW = 0
In case of an overvoltage event (V-SOV OFF) the outputs are
switched to high impedance state and the Vs Monitor bit OV is
set.
-
OVW = 1
In case of an overvoltage event (V-SOV OFF) the Vs Monitor bit
OV is set. The status of the outputs are unchanged.
24/40
Doc ID 11778 Rev 7
L9942
SPI - control and status registers
5.4
Register 3
Table 17.
Register 3
Current profile 3
PWM counter
PWM
Current profile 2
Bit
12
11
10
9
8
7
6
5
4
3
2
1
0
Access
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
I4
I3
I2
I1
I0
D1
D0
NPW M
I4
I3
I2
I1
I0
The meaning of the different bits is as follows:
I4 I3 I2 I1 I0
These bits are loaded in register1 DAC Phase A or B if needed.
See also parameter Table 12
D1 D0
These bits are for threshold value in counter of active time during
signal PWM.
-
NPWM
This bit switches internal PWM signal of bridge A to pin PWM if it
is set to 0, otherwise pin is in high resistance status.
-
5.5
Register 4 and 5
Table 18.
Register 4 and 5
Current profile 5 (7)
PWM counter
Current profile 4 (6)
Bit
12
11
10
9
8
7
6
5
4
3
2
1
0
Access
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
I4
I3
I2
I1
I0
D4(7)
D3(6)
D2(5)
I4
I3
I2
I1
I0
The meaning of the different bits is as follows:
I4 I3 I2 I1 I0
These bits are loaded needed. in register1 DAC Phase A
or B if needed.
See also parameter Table 12
D4 D3 D2 (register4) These bits are for threshold value in counter of active time
D7 D6 D5 (register5)
during signal PWM. LSB and next value are set in
register3 by D0 and D1.
Doc ID 11778 Rev 7
-
25/40
SPI - control and status registers
5.6
Register 6
Table 19.
Register 6
CLR
ST
(PWM)
L9942
Filter
Freq.
ST
REF
ERR
Open load
Current profile 8
Bit
12
11
10
9
8
7
6
5
4
3
2
1
0
Access
rw
rw
rw
rw
r
r
r
r
rw
rw
rw
rw
rw
Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
CLR6
SST
FT
PWM
Freq.
ST
I4
I3
I2
I1
I0
RREF Phase Phase
Error
B
A
The meaning of the different bits is as follows:
I4 I3 I2 I1 I0
These bits are loaded in register1 DAC Phase A or B if needed
Phase B Phase A
RREF Error
ST
This bit indicates if reference current is OK (150 µA 2 A
This bit resets all bits to 0 in register 7.
Doc ID 11778 Rev 7
L9942
SPI - control and status registers
5.8
Auxiliary logic blocks
5.8.1
Fault condition
Logical level at pin D0 represents fault condition. It is valid from first high to low edge of
signal CLK up to transfer of data bit D12. Fault bit is an logical OR of:
Control and status register 6 bit 5 and 6 for open load, bit 7 reference current failure
(RERR) and
Control and status register 7 bit 0 to bit 7 for overcurrent, bit 8 and 9 failure at VS
(UV,OV) and
bit 10 and bit 11 during high temperature (TW,TSD)
5.8.2
SPI communication monitoring
At the rising edge of the CSN signal the contents of the shift register will be transferred to
the selected data register. A counter monitors proper SPI communication. It counts rising
edges at pin CLK. The writing to the register is only enabled if exactly 16 bits are transmitted
within one communication frame (i.e. CSN low). If more or less clock pulses are counted
within one frame the complete frame will be ignored. This safety function is implemented to
avoid an activation of the output stages by a wrong communication frame. SPI
communication can be checked by loading a command twice and then answer at pin DO
must be same.
Note:
Due to this safety functionality a daisy chaining of SPI is not possible. Instead, a parallel
operation of the SPI bus by controlling the CSN signal of the connected ICs is
recommended.
5.8.3
PWM monitoring for stall detection
Control registers 4, 5, and 3 contain bits D0-D7, use for setting a stall detection threshold.
The value in this set of bits determine the minimum time for current rise over one quadrant of
motor driving. D7-D0 is compared with the sum of the rise times over one quadrant. When
the sum is less than the value stored in D7-D0 the ST bit (register 6 bit 8) is set to a logic “1”.
The PWM pin reflects the PWM control signal of the load current in bridge A. This is so after
power on when the SST bit (register 6, bit11) is reset to a logic “0”. If this bit is set to a
logical “1” then status of the ST bit 8 is mirrored to pin PWM. This provides stall detection
without the need of reading register 6 through the SPI bus.
Doc ID 11778 Rev 7
27/40
Logic with SPI - electrical characteristics
6
L9942
Logic with SPI - electrical characteristics
VS = 7 to 20 V, VCC = 3.0 to 5.3 V, EN=VCC, Tj = -40 to 150 °C, IREF = -200 A, unless
otherwise specified. The voltages are referred to GND and currents are assumed positive,
when the current flows into the pin.
6.1
Inputs: CSN, CLK, STEP, EN and DI
Table 21.
Inputs: CSN, CLK, STEP, EN and DI
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
-
V
Vin L
input low level
-
Vin H
input high level
-
-
0.6*VCC 0.7*VCC
V
Vin Hyst
input hysteresis
-
-
0.1*VCC
-
V
ICSN in
pull up current at input CSN
VCSN = VCC -1.5 V,
-50
-25
-10
µA
ICLK in
pull down current at input CLK
VCLK = 1.5 V
10
25
50
µA
pull down current at input DI
VDI = 1.5 V
10
25
50
µA
ISTEP in
pull down current at input STEP
VSTEP = 1.5 V
10
25
50
µA
REN in
resistance at input EN to GND
VEN in = VCC
110
510
k
Cin (1)
input capacitance at input CSN,
CLK, DI and PWM
0 V < VCC < 5.3 V
15
pF
IDI in
0.3*VCC 0.4*VCC
-
10
1. Parameter guaranteed by design.
6.2
DI timing
Table 22.
DI timing (see Figure 11 and Figure 13) (1)
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
tCLK
Clock period
VCC = 5 V
250
-
-
ns
tCLKH
Clock high time
VCC = 5 V
100
-
-
ns
tCLKL
Clock low time
VCC = 5 V
100
-
-
ns
tset CSN
CSN set up time, CSN low before
rising edge of CLK
VCC = 5 V
100
-
-
ns
tset CLK
CLK set up time, CLK high before
rising edge of CSN
VCC = 5 V
100
-
-
ns
tset DI
DI set up time
VCC = 5 V
50
-
-
ns
thold DI
DI hold time
VCC = 5 V
50
-
-
ns
tr in
Rise time of input signal DI, CLK,
CSN
VCC = 5 V
-
-
25
ns
tf in
Fall time of input signal DI, CLK,
CSN
VCC = 5 V
-
-
25
ns
1. DI timing parameters tested in production by a passed/failed test:
Tj=-40°C/+25°C: SPI communication @5MHz; Tj=+125°C: SPI communication @4.25MHz
28/40
Doc ID 11778 Rev 7
L9942
Logic with SPI - electrical characteristics
6.3
Outputs: DO, PWM
Table 23.
Outputs: DO, PWM
Symbol
Parameter
VDOoutL
Test condition
Min.
Typ.
Max.
Unit
Output low level
VCC = 5 V, ID = 2 mA
-
0.2
0.4
V
output high level
VCC = 5 V, ID = -2 mA
VCC 0.4
VCC 0.2
-
V
IDOoutLK
Tristate leakage current
VCSN = VCC,
0 V < VDO < VCC
-10
-
10
µA
IPWMoutLK
Tristate leakage current
Register3bit5=1 (NPWM)
0 V < VPWM < VCC
-10
-
10
µA
Tristate input capacitance
VCSN = VCC,
0 V < VCC < 5.3 V
-
10
15
pF
Min.
Typ.
Max.
Unit
VPWMoutL
VDOoutH
VPWMoutH
Cout (1)
6.4
Output: DO timing
Table 24.
Output: DO timing (see Figure 12 and Figure 13)
Symbol
Parameter
Test condition
tr DO
DO rise time
CL = 100 pF, Iload = -1 mA
-
50
100
ns
tf DO
DO fall time
CL = 100 pF, Iload = 1 mA
-
50
100
ns
ten DO tri L
DO enable time from tristate to low CL = 100 pF, Iload = 1 mA pullup load to VCC
level
-
50
250
ns
tdis DO L tri
DO disable time from low level to
tristate
CL = 100 pF, Iload = 4 mA pullup load to VCC
-
50
250
ns
ten DO tri H
DO enable time from tristate to
high level
CL = 100 pF, Iload = -1 mA pulldown load to GND
-
50
250
ns
tdis DO H tri
DO disable time from high level to
tristate
CL = 100 pF, Iload = -4 mA
-
50
250
ns
-
50
250
ns
Min.
Typ.
Max.
Unit
2
-
-
µs
td DO
DO delay time
6.5
CSN timing
Table 25.
CSN timing
Symbol
Parameter
tCSN_HI,min(1) CSN high time, active mode
pull-down load to GND
VDO < 0.3 VCC, VDO > 0.7
VCC, CL = 100 pF
Test condition
Transfer of SPI-command to
Input Register
1. Parameter guaranteed by design.
Doc ID 11778 Rev 7
29/40
Logic with SPI - electrical characteristics
6.6
STEP timing
Table 26.
STEP timing
Symbol
tSTEPmin(1)
L9942
Parameter
Test condition
STEP low or high time
Min.
Typ.
Max.
Unit
2
-
-
µs
-
1. Parameter guaranteed by design.
Figure 10. Transfer timing diagram
t
CSN_HI,min
CSN high to low: DO enabled
CSN
time
CLK
0
1
2
3
4
5
6
7
8
9
10 11 12
13 14 15
0
1
time
DI: data will be accepted on the rising edge of CLK signal
actual data
DI
A2
A1 A0 D12D11 D10 D9 D8 D7 D6
new data
D5 D4 D3 D2
D1 D0
A2
A1
time
DO: data will change on the falling edge of CLK signal
status information
DO
D12D11 D10 D9 D8 D7 D6
D5 D4 D3 D2
D1 D0
time
CSN low to high: actual data is
transfered to registers
fault bit
fault bit
actual data
old data
Control and Status Register
time
Figure 11. Input timing
0.8 VCC
t CLK
CSN
0.2 VCC
t set CSN
t CLKH
t
set CLK
0.8 VCC
CLK
0.2 VCC
t set DI
t hold DI
t CL KL
0.8 VCC
DI
Valid
Valid
0.2 VCC
30/40
Doc ID 11778 Rev 7
L9942
Logic with SPI - electrical characteristics
Figure 12. SPI - DO valid data delay time and valid time
tf in
t r in
0.8 VCC
0.5 VCC
0.2 VCC
CLK
t r DO
DO
(low to high)
0.8 VCC
0.2 VCC
td DO
t f DO
0.8 VCC
DO
(high to low)
0.2 VCC
Figure 13. DO enable and disable time
tf
tr
in
in
0 .8 V C C
50%
0 .2 V C C
C S N
D O
p u ll - u p lo a d to V C C
C L = 10 0 pF
50%
ten
D O tri L
t d is
D O L tri
50%
D O
p u ll- d o w n lo a d t o G N D
C L = 10 0 pF
ten
D O tri H
Doc ID 11778 Rev 7
t d is
D O H tri
31/40
Logic with SPI - electrical characteristics
L9942
Figure 14. Timing of status bit 0 (fault condition)
CSN high to low and CLK stays low: status information of data bit 0 (fault condition) is transferred to D0
CSN
time
CLK
time
DI
time
DI: data is not accepted
D0
D0
0
time
D0: status information of data bit 0 (fault condition) will stay as long as CSN is low
32/40
Doc ID 11778 Rev 7
L9942
Appendix
7
Appendix
7.1
Stall detection
The L9942 contains logic blocks designed to detect a motor stall caused by excessive
mechanical load.During a motor stall condition the load current rises much faster than
during normal operation. The L9942 measures this time and compares it to a programmed
value.
This is done by summing the PWM on times for one full quadrant. For a full wave stepping
this is just one value (step 0). For microstepping this includes 8 separate values added
together, one for each step. This measurement is only done on phase A during the
quadrants where the current is increasing naturally (quadrants 1 and 3 of Figure 15); e.g.
stall detection is active during phase counter values 1 to 8 and 17 to 24 for DIR=0. During
the quadrants where the current is decreasing fast decay recirculation interferes with
accurate measurement of this time. If the sum of the PWM on time is less than a
programmed threshold stored in D0-D7, stall is detected and indicated as a logic “1” in the
stall (ST) bit found in register 6 bit 8 (Figure 15 bottom). If bit 11 of register 6 is set to logical
“1” then the ST bit is mirrored to the PWM pin providing detection externally.The register
values DT7-DT0 store the threshold value in 16us intervals. These bits can be found
interstitially in register 3 (D0, D1), register4 (D2, D3, D4) and register5 (D5, D6, D7).
Care should be taken when deciding the threshold timing. Motor current slew rates are
dependant on the driving voltage, the actual speed of the motor, the back EMF of the motor
as well as the motor and the inductance. Be sure to set your threshold well away from what
can be seen in normal operation at any temperature.
7.2
Step clock input
The Step clock input allows to run one device in micro-step mode, or several devices
simultaneously with cost effective 8 bit µController. In case of the L9942, the SPI
communication link provides only the settings for motor operation mode. Motor commutation
as high duty process is outsourced to a parallel driven pin. Without this step clock input, the
SPI command would also have to clock the motor, leading to a high SPI speed. For full
micro-step operation or simultaneous motor drive, an 8 bit µController could be rapidly
overloaded.
7.3
Load current control and detection of overcurrent (shortages
at outputs)
The L9942 controls load current in the two full bridges by using a pulls with modulation
(PWM) regulator. The mirrored output current of active HS switch is compared with a
programmed reference current (e.g. in figure A2 HSA1 and HSB2). Bridge is switched off if
current has exceeded the programmed limit value. A second comparator of the related LS
switch uses the mirrored load current to detect an overcurrent to ground during ON state of
bridges (e.g. in Figure 16 LSA2 and LSB1). The event of shortage from output to supply
voltage VS is detectable, but short current between outputs is limited through PWM
controller and so an overcurrent failure will not occur.
Load currents decrease more or less fast during OFF state of bridges depending on
selected decay mode. Slow decay mode is released by activating the HS switches of the
Doc ID 11778 Rev 7
33/40
Appendix
L9942
bridge and current comparator has as new reference the overcurrent limit. A shortage to
ground can be detected, but not between the outputs.
Is it recommended to use the different fast decay modes too, especially in period if the load
current has to reduce from step to step. The duration of fast decay can set by fixed time ore
that it depends on the comparator signal utilizing the second current mirror at LS switch.
There can be monitored the undershoot of bridge current during OFF state.
Fast decay can be seen as switching the bridge in opposite direction, if it is compared to ON
state before. The load current control at HS switch is not used, but the comparator is still
active. The reference value is changed to overcurrent limit and a shortage to ground or now
between the outputs too will result in a signal. The internal filter time of at least 4 us will
inhibit the signal in many applications. Then you can use the mode “auto decay without any
delay time“ (On Section 5.1 mode 100). On page 12 you can find in the lower part of
Figure 3 the phase counter values, when fast decay as only part of mixed decay is used and
the shortages can be detected during a longer time. After this it is signalized in register 7 as
overcurrent in HS switch (e.g. in Figure 17 HSA1).
34/40
Doc ID 11778 Rev 7
L9942
Appendix
Figure 15. Stall detection
Load Current Rising During High Speed
Counter value is above threshold value.
PWM activ detection
Stall
Time
Threshold
16us *
Register 5
Register 4 Reg3
bit7 bit6 bit5 bit7 bit6 bit5 bit7 bit6
D7
D6
PWM activ detection
Time
D5
D4
D3
D2
D1
D0
PWM activ detection
Stall
Threshold
Stall
Threshold
PWM activ
counter
PWM activ
counter
No
Stall Signal
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Phase Counter
0 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Activ
sampling and
threshold
Current Driver A
0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1
Activ
sampling and
threshold
Current Driver A
Adress of Current
Profile Entry
0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1
Adress of Current
Profile Entry
8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7
Current Driver B
Current Driver B
8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7
STEP Signal
Micro Stepping Mode: DIR=0
Micro Stepping Mode: DIR=1
Load Current Rising During Low Speed or Stall
Counter value is below threshold value.
PWM activ detection
PWM activ detection
PWM activ detection
Time
Stall
Threshold
Stall Signal
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Phase Counter
0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1
Current Driver A
Stall Signal
0 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Activ
sampling and
threshold
Activ
sampling and
threshold
PWM activ
counter
PWM activ
counter
Stall
Threshold
Current Driver A
Adress of Current
Profile Entry
0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1
Adress of Current
Profile Entry
8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7
Current Driver B
Current Driver B
8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7
STEP Signal
Micro Stepping Mode: DIR=0
Doc ID 11778 Rev 7
Micro Stepping Mode: DIR=1
35/40
Appendix
L9942
Figure 16. Reference generation for PWM control (switch on)
1
Register 0
UP/Down
PhaseCounter 1
Count by
1,2,4,8
0
0
Decay Mode
0
0
DM2
1
DM1
DM0
Slew Rate
SR1
Counter value changes after an signal at STEP to next one
depending on selected stepping mode described in figure 3
(e.g. during micro stepping to value 2) .
StepMode DIR
SR0
0
0
0
STEP
0
0
0
0 1 2 3 0 1 2 3 0 1 2 3
A3
Address Calculation
A2
A1
A0
MUX
MUX
MUX
A2
A1
A0
Phase A
Adr
A3=0
A[3..0]
Adr
Phase B
A3=1
neg(A[3..0])
Adr
A3=0
neg(A[3..0])
PWM Control With HS Current Monitoring
Overcurrent Detection At LS Switch
A3=1
Adr A[3..0]
Current-Profile Table
stored in register2, ...6
9
5
1
1
1
1
1
Profile 8
1
1
1
1
0
Profile 7
1
1
1
0
1
Profile 6
1
1
0
1
0
Profile 5
1
0
1
1
0
Profile 4
1
0
0
0
1
Profile 3
0
1
1
0
0
Profile 2
Phase Counter
5
0
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
1
Current Driver A
5
Adress of Current
Profile Entry
Phase A
5
5
0
1
2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1
8
7
6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7
5
5
Current Driver B
Adress of Current
Profile Entry
Phase B
5
0
0
1
1
0
Profile 1
0
0
0
0
0
Profile 0
5
STEP Signal
5
HS Current
Monitoring
(Load control)
Register 1
DAC Scale
DI
0
0
0
95 mA
1
1
1
1
0
0
DAC
Full Scale
0
1
1
0
100mA * 6/31 = 18.4mA
100mA * 30/31 = 91.9mA
5 bit DAC
Phase B
I REF
REF
200 uA
DAC Phase A
DAC Phase B
I LIMIT B
LIMIT HSA1
I LIMIT A
5 bit DAC
Phase A
+
2mA
2mA
I MAX
HS1 on
QA1
+
-
IA
+
+
QB1
2mA
LS Current
Monitoring
(Overcurrentl)
IQA1LIM
1000
-
2mA
OC LSB1
-
+
LS1 on
+
-
2mA
IB
+
QA2
2mA
OC
LSA2
+
-
LS2 on
-
LIMIT HSB2
HS Current
Monitoring
(Load control)
+
2mA
2mA
IQA2LIM
1000
HS2on
+
QB2
+
-
+
-
36/40
Doc ID 11778 Rev 7
-
LS Current
Monitoring
(Overcurrent)
L9942
Appendix
Figure 17. Reference generation for PWM control (decay)
1
Register 0
UP/Down
1
PhaseCounter
Count by
1,2,4,8
0
0
0
Decay Mode
0
1
DM2
DM1
DM0
StepMode DIR
Slew Rate
SR1
Counter value changes after an signal at STEP to next one
depending on selected stepping mode described in figure 1.2
(e.g. during micro stepping to value 2) .
SR0
0
0
0
STEP
0
0 1 2 3
A3
Address Calculation
0
0 1 2 3
0 1 2 3
A2
A1
A0
MUX
MUX
MUX
A2
A1
A0
Phase A
Adr
A3=0
A[3..0]
Adr
Auto Decay
0
Mixed Decay
Fast and Slow
Decay
Slow Decay
Phase B
A3=1
neg(A[3..0])
Adr
A3=1
Adr A[3..0]
A3=0
neg(A[3..0])
Current-Profile Table
stored in register2, ...6
9
5
1
1
1
1
1
Profile 8
1
1
1
1
0
Profile 7
1
1
1
0
1
Profile 6
1
1
0
1
0
Profile 5
1
0
1
1
0
Profile 4
1
0
0
0
1
Profile 3
0
1
1
0
0
Profile 2
Phase Counter
5
0
1
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Current Driver A
5
Adress of Current
Profile Entry
Phase A
5
5
0
1
2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1
8
7
6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7
5
5
Current Driver B
Adress of Current
Profile Entry
Phase B
5
0
0
1
1
0
Profile 1
0
0
0
0
0
Profile 0
5
STEP Signal
5
HS Current
Monitoring
(Overcurrent)
Register 1
DAC Scale
DI
0
0
0
95 mA
1
1
1
1
DAC
Full Scale
0
0
0
1
1
0
100mA * 6/31 = 18.4mA
95mA * 30/31 = 91.9mA
5 bit DAC
Phase B
I REF
REF
200 uA
DAC Phase A
DAC Phase B
I LIMIT B
OC
I LIMIT A
5 bit DAC
Phase A
HSA1
+
QA1
2mA
-
I MAX
HS Current
Monitoring
(Overcurrent)
+
-
OC
HSB1
+
2mA
2mA
IQB1
1000
+
HS1 on
-
HSB1
+
Fast
Decay
IB
2mA
+
-
+
+
QB2
2mA
HS2 on
QA2
2mA
-
2mA
IA
-
OC
+
Slow
Decay
QB1
+
-
LS Current
Monitoring
(Load Control)
HS1 on
2mA
HS Current
Monitoring
(Overcurrent)
-
LS2on
+
-
LIMIT LSB2
+
-
Doc ID 11778 Rev 7
37/40
Package information
8
L9942
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Figure 18. PowerSSO24 mechanical data and package dimensions
Dim.
A
A2
a1
b
c
D (1)
E (1)
e
e3
F
G
G1
H
h
k
L
O
Q
S
T
U
N
X
Y
Min.
mm
Typ.
2.15
0
0.33
0.23
10.10
7.40
Max.
2.45
2.35
0.10
0.51
0.32
10.50
0.084
0
0.013
0.009
0.398
7.60
0.291
0.80
8.80
2.30
0.55
Max.
0.0965
0.0925
0.003
0.020
0.012
0.413
OUTLINE AND
MECHANICAL DATA
0.299
0.031
0.346
0.090
0.10
0.06
10.50 0.398
0.40
0˚ (min.), 8˚ (max.)
0.85 0.0217
10.10
1.20
0.80
2.90
3.65
1.0
4.10
6.50
4.90(4)
inch
Typ.
Min.
10˚ (max)
4.70 0.161
7.10 0.256
5.50(4) 0.192(4)
0.004
0.002
0.413
0.016
0.0335
0.047
0.031
0.114
0.143
0.039
0.185
0.279
0.216(4)
(1) “D and E1” do not include mold flash or protusions.
Mold flash or protusions shall not exceed 0.15mm (0.006”)
(2) No intrusion allowed inwards the leads.
(3) Flash or bleeds on exposed die pad shall not exceed 0.4 mm per side
(4) Variation for small window leadframe option.
PowerSSO24
(Exposed pad down)
7412818 I
38/40
Doc ID 11778 Rev 7
L9942
9
Revision history
Revision history
Table 27.
Document revision history
Date
Revision
Changes
10-Nov-2005
1
Initial release.
04-May-2006
2
Feature list updated.
Part numbers updated.
21-Sep-2006
3
Feature list updated.
Table 21 on page 28 updated.
09-Jul-2007
4
Updated the order codes (see Table 1: Device summary on page 1).
Changed the status from Preliminary data to Datasheet.
02-Feb-2009
5
Updated the following tables: 2, 9, 14, 15, 16, 17, 18, 19 and 20.
Updated the following chapters: 2.4, 5.1, 5.2, 5.3, 5.4, 5.5, 5.6 and
5.7.
15-May-2009
6
Updated Figure 18: PowerSSO24 mechanical data and package
dimensions on page 38.
19-Sep-2013
7
Updated Disclaimer.
Doc ID 11778 Rev 7
39/40
L9942
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2013 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
40/40
Doc ID 11778 Rev 7