UPSD3212A
UPSD3212C, UPSD3212CV
Flash programmable system devices
with 8032 MCU and USB and programmable logic
Features
■
Fast 8-bit 8032 MCU
– 40 MHz at 5.0 V, 24 MHz at 3.3 V
– Core, 12-clocks per instruction
■
Dual Flash memories with memory
management
– Place either memory into 8032 program
address space or data address space
– Read-while-write operation for inapplication programming and EEPROM
emulation
– Single voltage program and erase
– 100 K minimum erase cycles, 15-year
retention
■
■
■
■
LQFP52 (T)
52-lead, thin,
quad flat package
Clock, reset, and supply management
– Normal, idle, and power down modes
– Power-on and low voltage reset supervisor
– Programmable watchdog timer
Programmable logic, general-purpose
– 16 macrocells
– Implements state machines, glue-logic, etc.
Timers and interrupts
– Three 8032 standard 16-bit timers
– 10 Interrupt sources with two external
interrupt pins
LQFP80 (U)
80-lead, thin, quad
flat package
■
Communication interfaces
– USB v1.1, low-speed 1.5 Mbps,
3 endpoints
– I2C master/slave bus controller
– Two UARTs with independent baud rate
– Six I/O ports with up to 46 I/O pins
– 8032 address/data bus available on
TQFP80 package
– 5 PWM outputs, 8-bit resolution
■
JTAG in-system programming
– Program the entire device in as little as
10 seconds
■
Single supply voltage
– 4.5 to 5.5 V
– 3.0 to 3.6 V
■
ECOPACK® packages
A/D converter
– Four channels, 8-bit resolution, 10 µs
Table 1.
Device summary
Order code
UPSD3212C-40T6
Max. clock 1st
2nd
8032
SRAM GPIO USB
VCC (V)
(MHz)
Flash Flash
bus
40
64 KB 16 KB
2 KB
37
No
No
Pkg.
Temp.
4.5-5.5 TQFP52 –40°C to 85°C
UPSD3212CV-24T6
24
64 KB 16 KB
2 KB
37
No
No
3.0-3.6 TQFP52 –40°C to 85°C
UPSD3212C-40U6
40
64 KB 16 KB
2 KB
46
No
Yes
4.5-5.5 TQFP80 –40°C to 85°C
UPSD3212CV-24U6
24
64 KB 16 KB
2 KB
46
No
Yes
3.0-3.6 TQFP80 –40°C to 85°C
UPSD3212A-40T6
40
64 KB 16 KB
2 KB
37
Yes
No
4.5-5.5 TQFP52 –40°C to 85°C
UPSD3212A-40U6
40
64 KB 16 KB
2 KB
46
Yes
Yes
4.5-5.5 TQFP80 –40°C to 85°C
January 2009
Rev 6
1/181
www.st.com
1
Contents
UPSD3212A, UPSD3212C, UPSD3212CV
Contents
1
UPSD321xx description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1
2
2/181
52-pin package I/O port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Architecture overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.1
Memory organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2
Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2.1
Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2.2
B register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2.3
Stack pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2.4
Program counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.2.5
Program status word . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.2.6
Registers R0~R7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.2.7
Data pointer register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.3
Program memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.4
Data memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.5
RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.6
XRAM-PSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.7
SFR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.8
Addressing modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.8.1
Direct addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.8.2
Indirect addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.8.3
Register addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.8.4
Register-specific addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.8.5
Immediate constants addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.8.6
Indexed addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.9
Arithmetic instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.10
Logical instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2.11
Data transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2.11.1
Internal RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2.11.2
External RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.11.3
Lookup tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2.12
Boolean instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.13
Relative offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
UPSD3212A, UPSD3212C, UPSD3212CV
Contents
2.14
Jump instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.15
Machine cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3
UPSD321xx hardware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4
MCU module description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.1
5
6
7
Special function registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Interrupt system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.1
External Int0 interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.2
Timer 0 and 1 interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.3
Timer 2 interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.4
I2C interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.5
External Int1 interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
5.6
USB interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
5.7
USART interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
5.8
Interrupt priority structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
5.9
Interrupt enable structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5.10
How interrupts are handled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Power-saving mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.1
Idle mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.2
Power-down mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.3
Power control register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
6.4
Idle mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
6.5
Power-down mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
I/O ports (MCU module) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
7.1
Port type and description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
8
Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
9
Supervisory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
9.1
External reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
9.2
Low VDD voltage reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3/181
Contents
UPSD3212A, UPSD3212C, UPSD3212CV
9.3
Watchdog timer overflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
9.4
USB reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
10
Watchdog timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
11
Timer/counters (Timer 0, Timer 1 and Timer 2) . . . . . . . . . . . . . . . . . . 58
11.1
11.2
12
13
15
4/181
11.1.1
Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
11.1.2
Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
11.1.3
Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
11.1.4
Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Timer 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Standard serial interface (UART) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
12.1
Multiprocessor communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
12.2
Serial port control register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
12.2.1
Baud rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
12.2.2
Using Timer 1 to generate baud rates . . . . . . . . . . . . . . . . . . . . . . . . . . 67
12.2.3
Using Timer/counter 2 to generate baud rates . . . . . . . . . . . . . . . . . . . 67
12.2.4
More about Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
12.2.5
More about Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
12.2.6
More about Modes 2 and 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Analog-to-digital convertor (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
13.1
14
Timer 0 and Timer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
ADC interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Pulse width modulation (PWM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
14.1
4-channel PWM unit (PWM 0-3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
14.2
Programmable period 8-bit PWM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
14.3
PWM 4-channel operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
I2C interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
15.1
Serial status register (SxSTA: S1STA, S2STA) . . . . . . . . . . . . . . . . . . . . 85
15.2
Data shift register (SxDAT: S1DAT, S2DAT) . . . . . . . . . . . . . . . . . . . . . . . 85
15.3
Address register (SxADR: S1ADR, S2ADR) . . . . . . . . . . . . . . . . . . . . . . 86
UPSD3212A, UPSD3212C, UPSD3212CV
16
17
Contents
USB hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
16.1
USB related registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
16.2
Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
16.2.1
USB physical layer characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
16.2.2
Low speed driver characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
16.3
Receiver characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
16.4
External USB pull-up resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
PSD module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
17.1
Functional overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
17.2
In-system programming (ISP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
18
Development system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
19
PSD module register description and address offset . . . . . . . . . . . . 103
20
PSD module detailed operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
21
Memory blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
21.1
Primary Flash memory and secondary Flash memory description . . . . 105
21.2
Memory block select signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
21.2.1
Ready/Busy (PC3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
21.2.2
Memory operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
21.3
Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
21.4
Power-down instruction and Power-up mode . . . . . . . . . . . . . . . . . . . . . 107
21.4.1
21.5
21.6
Power-up mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
21.5.1
Read memory contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
21.5.2
Read memory sector protection status . . . . . . . . . . . . . . . . . . . . . . . . 108
21.5.3
Reading the Erase/Program status bits . . . . . . . . . . . . . . . . . . . . . . . . 108
21.5.4
Data polling flag (DQ7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
21.5.5
Toggle flag (DQ6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
21.5.6
Error flag (DQ5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
21.5.7
Erase time-out flag (DQ3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Programming Flash memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
21.6.1
Data Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
5/181
Contents
UPSD3212A, UPSD3212C, UPSD3212CV
21.6.2
21.7
21.8
21.9
Data toggle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Erasing Flash memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
21.7.1
Flash Bulk Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
21.7.2
Flash Sector Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
21.7.3
Suspend Sector Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
21.7.4
Resume Sector Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Specific features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
21.8.1
Flash memory sector protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
21.8.2
Reset Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
SRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
21.10 Sector Select and SRAM Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
21.10.1 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
21.10.2 Memory Select configuration in Program and Data spaces . . . . . . . . . 116
21.10.3 Separate Space mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
21.10.4 Combined Space modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
21.11 Page register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
22
PLDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
22.1
Turbo bit in PSD module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
22.2
Decode PLD (DPLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
22.3
Complex PLD (CPLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
22.4
Output macrocell (OMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
22.5
Product term allocator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
22.6
23
6/181
22.5.1
Loading and Reading the Output Macrocells (OMC) . . . . . . . . . . . . . . 124
22.5.2
OMC mask register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
22.5.3
Output enable of the OMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Input macrocells (IMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
I/O ports (PSD module) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
23.1
General port architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
23.2
Port operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
23.3
MCU I/O mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
23.4
PLD I/O mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
23.5
Address Out mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
23.6
Peripheral I/O mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
UPSD3212A, UPSD3212C, UPSD3212CV
Contents
23.7
JTAG in-system programming (ISP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
23.8
Port configuration registers (PCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
23.9
23.8.1
Control register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
23.8.2
Direction register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
23.8.3
Drive Select register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Port data registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
23.9.1
Data In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
23.9.2
Data Out register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
23.9.3
Output macrocells (OMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
23.9.4
OMC mask register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
23.9.5
Input macrocells (IMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
23.9.6
Enable out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
23.10 Ports A and B – functionality and structure . . . . . . . . . . . . . . . . . . . . . . 133
23.11 Port C – functionality and structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
23.12 Port D – functionality and structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
23.13 External chip select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
24
25
26
Power management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
24.1
PLD power management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
24.2
PSD chip select input (CSI, PD2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
24.3
Input clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
24.4
Input control signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
RESET timing and device status at reset . . . . . . . . . . . . . . . . . . . . . . 142
25.1
Warm RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
25.2
I/O pin, register and PLD status at RESET . . . . . . . . . . . . . . . . . . . . . . 142
Programming in-circuit using the JTAG serial interface . . . . . . . . . . 144
26.1
Standard JTAG Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
26.2
JTAG extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
26.3
Security and Flash memory protection . . . . . . . . . . . . . . . . . . . . . . . . . . 145
27
Initial delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
28
AC/DC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
7/181
Contents
UPSD3212A, UPSD3212C, UPSD3212CV
29
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
30
EMC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
30.1
30.2
30.3
Functional EMS (electromagnetic susceptibility) . . . . . . . . . . . . . . . . . . 151
30.1.1
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
30.1.2
FTB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Designing hardened software to avoid noise problems . . . . . . . . . . . . . 151
30.2.1
Software recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
30.2.2
Prequalification trials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Absolute maximum ratings (electrical sensitivity) . . . . . . . . . . . . . . . . . . 152
30.3.1
Electro-static discharge (ESD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
30.3.2
Latch-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
30.3.3
Dynamic latch-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
31
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
32
Package mechanical information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
33
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
34
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
8/181
UPSD3212A, UPSD3212C, UPSD3212CV
1
UPSD321xx description
UPSD321xx description
The UPSD321xx Series combines a fast 8051-based microcontroller with a flexible memory
structure, programmable logic, and a rich peripheral mix including USB, to form an ideal
embedded controller. At its core is an industry-standard 8032 MCU operating up to 40MHz.
A JTAG serial interface is used for In-System Programming (ISP) in as little as 10 seconds,
perfect for manufacturing and lab development.
The USB 1.1 low-speed interface has one Control endpoint and two Interrupt endpoints
suitable for HID class drivers.
The 8032 core is coupled to Programmable System Device (PSD) architecture to optimize
the 8032 memory structure, offering two independent banks of Flash memory that can be
placed at virtually any address within 8032 program or data address space, and easily
paged beyond 64 Kbytes using on-chip programmable decode logic.
Dual Flash memory banks provide a robust solution for remote product updates in the field
through In-Application Programming (IAP). Dual Flash banks also support EEPROM
emulation, eliminating the need for external EEPROM chips.
General purpose programmable logic (PLD) is included to build an endless variety of gluelogic, saving external logic devices. The PLD is configured using the software development
tool, PSDsoft Express, available from the web at www.st.com/psm, at no charge.
The UPSD321xx also includes supervisor functions such as a programmable watchdog
timer and low-voltage reset.
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
9/181
UPSD321xx description
Figure 1.
UPSD3212A, UPSD3212C, UPSD3212CV
UPSD321xx block diagram
uPSD321x
(3) 16-bit
Timer/
Counters
P3.0:7
1st Flash Memory:
64K Bytes
8032
MCU
Core
(2)
External
Interrupts
Programmable
Decode and
Page Logic
I2C
2nd Flash Memory:
16K Bytes
SRAM:
2K Bytes
(8) GPIO, Port 3
P1.0:7
(8) GPIO, Port 1
(4) 8-bit ADC
SYSTEM BUS
UART0
General
Purpose
Programmable
Logic,
16 Macrocells
(8) GPIO, Port A
(80-pin only)
PA0:7
(8) GPIO, Port B
PB0:7
(2) GPIO, Port D
PD1:2
(4) GPIO, Port C
PC0:7
UART1
P4.0:7
USB+,
USB–
JTAG ISP
(5) 8-bit PWM
8032 Address/Data/Control Bus
(80-pin device only)
(8) GPIO, Port 4
Supervisor:
Watchdog and Low-Voltage Reset
USB v1.1
VCC, VDD, GND, Reset, Crystal In
MCU
Bus
Dedicated
Pins
AI10428b
10/181
UPSD3212A, UPSD3212C, UPSD3212CV
40 P1.6/ADC2
41 P1.7/ADC3
42 PB7
43 PB6
44 RESET_
45 GND
46 VREF
47 PB5
48 PB4
49 PB3
50 PB2
51 PB1
TQFP52 connections
52 PB0
Figure 2.
UPSD321xx description
PD1/CLKIN 1
39 P1.5/ADC1
PC7 2
38 P1.4/ADC0
JTAG TDO 3
37 P1.3/TXD1
JTAG TDI 4
USB–(1) 5
36 P1.2/RXD1
35 P1.1/T2X
PC4/TERR_ 6
34 P1.0/T2
USB+ 7
VCC 8
33 VCC
32 XTAL2
GND 9
31 XTAL1
PC3/TSTAT 10
30 P3.7/SCL1
PC2/VSTBY 11
29 P3.6/SDA1
P3.3/EXINT1 26
P3.2/EXINT0 25
P3.1/TXD 24
P3.0/RXD 23
P4.0 22
P4.1 21
P4.2 20
GND 19
P4.3/PWM0 18
P4.4/PWM1 17
P4.5/PWM2 16
27 P3.4/T0
P4.6/PWM3 15
28 P3.5/T1
JTAG TMS 13
P4.7/PWM4 14
JTAG TCK 12
AI07423c
1. Pull-up resistor required on pin 5 (2 kΩ for 3 V devices, 7.5 kΩ for 5 V devices) for all 52-pin devices, with
or without USB function.
11/181
UPSD321xx description
61 P1.6/ADC2
62 WR_
63 PSEN_
64 P1.7/ADC3
65 RD_
66 PB7
67 PB6
68 RESET_
69 GND
70 VREF
72 PB5
71 NC(2)
73 PB4
74 PB3
75 P3.0/RXD0
76 PB2
77 P3.1/TXD0
78 PB1
79 P3.2/EXINT0
TQFP80 connections
80 PB0
Figure 3.
UPSD3212A, UPSD3212C, UPSD3212CV
PD2 1
60 P1.5/ADC1
P3.3 /EXINT1 2
59 P1.4/ADC0
PD1/CLKIN 3
58 P1.3/TXD1
ALE 4
57 A11
PC7 5
56 P1.2/RXD1
JTAG/TDO 6
55 A10
JTAG/TDI 7
USB–(1) 8
54 P1.1/TX2
53 A9
PC4/TERR_ 9
52 P1.0/T2
USB+ 10
NC(2) 11
51 A8
50 VCC
VCC 12
49 XTAL2
GND 13
48 XTAL1
PC3/TSTAT 14
47 AD7
PC2/VSTBY 15
46 P3.7/SCL1
JTAG TCK 16
NC(2) 17
45 AD6
P4.7/PWM4 18
43 AD5
P4.6/PWM3 19
42 P3.5/T1
44 P3.6/SDA1
JTAG TMS 20
P3.4/T0 40
AD3 39
AD2 38
AD1 37
AD0 36
PA0 35
PA1 34
P4.0 33
PA2 32
P4.1 31
P4.2 30
GND 29
PA3 28
P4.3/PWM0 27
PA4 26
P4.4/PWM1 25
PA5 24
P4.5/PWM2 23
PA6 22
PA7 21
41 AD4
AI07424c
1. Pull-up resistor required on pin 8 (2 kΩ for 3 V devices, 7.5 kΩ for 5 V devices) for all 82-pin devices, with
or without USB function.
2. NC = Not Connected
Table 2.
Port
pin
12/181
80-pin package pin description
Function
Signal
name
Pin
no.
In/
out
AD0
36
I/O
External Bus: Multiplexed
Address/Data bus A1/D1
AD1
37
I/O
Multiplexed Address/Data bus A0/D0
AD2
38
I/O
Multiplexed Address/Data bus A2/D2
AD3
39
I/O
Multiplexed Address/Data bus A3/D3
AD4
41
I/O
Multiplexed Address/Data bus A4/D4
AD5
43
I/O
Multiplexed Address/Data bus A5/D5
AD6
45
I/O
Multiplexed Address/Data bus A6/D6
Basic
Alternate
UPSD3212A, UPSD3212C, UPSD3212CV
Table 2.
Port
pin
UPSD321xx description
80-pin package pin description (continued)
Function
Signal
name
Pin
no.
In/
out
AD7
47
I/O
Multiplexed Address/Data bus A7/D7
P1.0
T2
52
I/O
General I/O port pin
Timer 2 Count input
P1.1
TX2
54
I/O
General I/O port pin
Timer 2 Trigger input
P1.2
RxD1
56
I/O
General I/O port pin
2nd UART Receive
P1.3
TxD1
58
I/O
General I/O port pin
2nd UART Transmit
P1.4
ADC0
59
I/O
General I/O port pin
ADC Channel 0 input
P1.5
ADC1
60
I/O
General I/O port pin
ADC Channel 1 input
P1.6
ADC2
61
I/O
General I/O port pin
ADC Channel 2 input
P1.7
ADC3
64
I/O
General I/O port pin
ADC Channel 3 input
A8
51
O
External Bus, Address A8
A9
53
O
External Bus, Address A9
A10
55
O
External Bus, Address A10
A11
57
O
External Bus, Address A11
P3.0
RxD0
75
I/O
General I/O port pin
UART Receive
P3.1
TxD0
77
I/O
General I/O port pin
UART Transmit
P3.2
EXINT0
79
I/O
General I/O port pin
Interrupt 0 input / Timer 0
gate control
P3.3
EXINT1
2
I/O
General I/O port pin
Interrupt 1 input / Timer 1
gate control
P3.4
T0
40
I/O
General I/O port pin
Counter 0 input
P3.5
T1
42
I/O
General I/O port pin
Counter 1 input
P3.6
SDA1
44
I/O
General I/O port pin
I2C Bus serial data I/O
P3.7
SCL1
46
I/O
General I/O port pin
I2C Bus clock I/O
P4.0
DDC
SDA
33
I/O
General I/O port pin
P4.1
DDC
SCL
31
I/O
General I/O port pin
P4.2
DDC
VSYNC
30
I/O
General I/O port pin
P4.3
PWM0
27
I/O
General I/O port pin
8-bit Pulse Width
Modulation output 0
P4.4
PWM1
25
I/O
General I/O port pin
8-bit Pulse Width
Modulation output 1
P4.5
PWM2
23
I/O
General I/O port pin
8-bit Pulse Width
Modulation output 2
P4.6
PWM3
19
I/O
General I/O port pin
8-bit Pulse Width
Modulation output 3
Basic
Alternate
13/181
UPSD321xx description
Table 2.
14/181
UPSD3212A, UPSD3212C, UPSD3212CV
80-pin package pin description (continued)
Function
Port
pin
Signal
name
Pin
no.
In/
out
P4.7
PWM4
18
I/O
General I/O port pin
USB–
8
I/O
Pull-up resistor required (2 kΩ for
3 V devices, 7.5 kΩ for 5 V devices)
VREF
70
O
Reference Voltage input for ADC
RD_
65
O
READ signal, external bus
WR_
62
O
WRITE signal, external bus
PSEN_
63
O
PSEN signal, external bus
ALE
4
O
Address Latch signal, external bus
RESET_
68
I
Active low RESET input
XTAL1
48
I
Oscillator input pin for system clock
XTAL2
49
O
Oscillator output pin for system clock
PA0
35
I/O
General I/O port pin
PA1
34
I/O
General I/O port pin
PA2
32
I/O
General I/O port pin
PA3
28
I/O
General I/O port pin
PA4
26
I/O
General I/O port pin
PA5
24
I/O
General I/O port pin
PA6
22
I/O
General I/O port pin
PA7
21
I/O
General I/O port pin
PB0
80
I/O
General I/O port pin
PB1
78
I/O
General I/O port pin
PB2
76
I/O
General I/O port pin
PB3
74
I/O
General I/O port pin
PB4
73
I/O
General I/O port pin
PB5
72
I/O
General I/O port pin
PB6
67
I/O
General I/O port pin
PB7
66
I/O
General I/O port pin
Basic
Alternate
Programmable 8-bit Pulse
Width modulation output 4
PLD macrocell outputs
PLD inputs
Latched address out (A0A7)
Peripheral I/O mode
PLD macrocell outputs
PLD inputs
Latched address out (A0A7)
UPSD3212A, UPSD3212C, UPSD3212CV
Table 2.
Port
pin
80-pin package pin description (continued)
Function
Signal
name
Pin
no.
In/
out
JTAG
TMS
20
I
JTAG pin
JTAG
TCK
16
I
JTAG pin
PC3
TSTAT
14
I/O
General I/O port pin
PC4
TERR_
9
I/O
General I/O port pin
JTAG
TDI
7
I
JTAG pin
JTAG
TDO
6
O
JTAG pin
5
I/O
General I/O port pin
3
I/O
General I/O port pin
PLD I/O
Clock input to PLD and
APD
PD2
1
I/O
General I/O port pin
PLD I/O
Chip select to PSD module
Vcc
12
Vcc
50
GND
13
GND
29
GND
69
PC7
PD1
CLKIN
USB+
1.1
UPSD321xx description
Basic
Alternate
PLD macrocell outputs
PLD inputs
JTAG pins are dedicated
pins
10
NC
11
NC
17
NC
71
52-pin package I/O port
The 52-pin package members of the UPSD321xx devices have the same port pins as those
of the 80-pin package except:
●
Port 0 (P0.0-P0.7, external address/data bus AD0-AD7)
●
Port 2 (P2.0-P2.3, external address bus A8-A11)
●
Port A (PA0-PA7)
●
Port D (PD2)
●
Bus control signal (RD,WR,PSEN,ALE)
●
Pin 5 requires a pull-up resistor (2 kΩ for 3 V devices, 7.5 kΩ for 5 V devices) for all
devices, with or without USB function.
15/181
Architecture overview
UPSD3212A, UPSD3212C, UPSD3212CV
2
Architecture overview
2.1
Memory organization
The UPSD321xx devices’ standard 8032 Core has separate 64-Kbyte address spaces for
Program memory and Data Memory. Program memory is where the 8032 executes
instructions from. Data memory is used to hold data variables. Flash memory can be
mapped in either program or data space. The Flash memory consists of two Flash memory
blocks: the main Flash memory (512 Kbit) and the Secondary Flash memory (128 Kbit).
Except during flash memory programming or update, Flash memory can only be read, not
written to. A Page Register is used to access memory beyond the 64-Kbyte address space.
Refer to the PSD module for details on mapping of the Flash memory.
The 8032 core has two types of data memory (internal and external) that can be read and
written. The internal SRAM consists of 256 bytes, and includes the stack area.
The SFR (Special Function Registers) occupies the upper 128 bytes of the internal SRAM,
the registers can be accessed by Direct addressing only. Another 2 Kbytes resides in the
PSD module that can be mapped to any address space defined by the user.
Figure 4.
Memory map and address space
MAIN
FLASH
EXT. RAM
INT. RAM
SFR
Indirect
Addressing
Direct
Addressing
FF
SECONDARY
FLASH
64KB
7F
16KB
2KB
Indirect
or
Direct
Addressing
0
Flash Memory Space
Internal RAM Space
(256 Bytes)
External RAM Space
(MOVX)
AI07425
2.2
Registers
The 8032 has several registers; these are the Program Counter (PC), Accumulator (A), B
Register (B), the Stack Pointer (SP), the Program Status Word (PSW), General purpose
registers (R0 to R7), and DPTR (Data Pointer register).
16/181
UPSD3212A, UPSD3212C, UPSD3212CV
Figure 5.
Architecture overview
8032 MCU registers
A
Accumulator
B
B Register
Stack Pointer
SP
PCH
PCL
Program Counter
PSW
Program Status Word
General Purpose
Register (Bank0-3)
Data Pointer Register
R0-R7
DPTR(DPH)
DPTR(DPL)
AI06636
2.2.1
Accumulator
The Accumulator is the 8-bit general purpose register, used for data operation such as
transfer, temporary saving, and conditional tests. The Accumulator can be used as a 16-bit
register with B Register as shown below.
Figure 6.
Configuration of BA 16-bit registers
B
B
A
A
Two 8-bit Registers can be used as a "BA" 16-bit Registers
AI06637
2.2.2
B register
The B Register is the 8-bit general purpose register, used for an arithmetic operation such
as multiply, division with Accumulator.
2.2.3
Stack pointer
The Stack Pointer Register is 8 bits wide. It is incremented before data is stored during
PUSH and CALL executions. While the stack may reside anywhere in on-chip RAM, the
Stack Pointer is initialized to 07h after reset. This causes the stack to begin at location 08h.
Figure 7.
Stack pointer
Stack Area (30h-FFh)
Bit 15
Bit 8 Bit 7
00h
Hardware Fixed
Bit 0
SP
00h-FFh
SP (Stack Pointer) could be in 00h-FFh
AI06638
17/181
Architecture overview
2.2.4
UPSD3212A, UPSD3212C, UPSD3212CV
Program counter
The Program Counter is a 16-bit wide which consists of two 8-bit registers, PCH and PCL.
This counter indicates the address of the next instruction to be executed. In RESET state,
the program counter has reset routine address (PCH:00h, PCL:00h).
2.2.5
Program status word
The Program Status Word (PSW) contains several bits that reflect the current state of the
CPU and select Internal RAM (00h to 1Fh: Bank0 to Bank3). The PSW is described in
Figure 8. It contains the Carry flag, the Auxiliary Carry flag, the Half Carry (for BCD
operation), the General Purpose flag, the Register Bank Select flags, the Overflow flag, and
Parity flag.
[Carry flag, CY]. This flag stores any carry or not borrow from the ALU of CPU after an
arithmetic operation and is also changed by the Shift Instruction or Rotate Instruction.
[Auxiliary Carry flag, AC]. After operation, this flag is set when there is a carry from Bit 3 of
ALU or there is no borrow from Bit 4 of ALU.
[Register Bank Select flags, RS0, RS1]. These flags select one of four banks
(00~07H:bank0, 08~0Fh:bank1, 10~17h:bank2, 17~1Fh:bank3) in Internal RAM.
[Overflow flag, OV]. This flag is set to '1' when an overflow occurs as the result of an
arithmetic operation involving signs. An overflow occurs when the result of an addition or
subtraction exceeds +127 (7Fh) or -128 (80h). The CLRV instruction clears the overflow
flag. There is no set instruction. When the BIT instruction is executed, Bit 6 of memory is
copied to this flag.
[Parity flag, P]. This flag reflects the number of Accumulator’s 1. If the number of
Accumulator’s 1 is odd, P=0; otherwise, P=1. The sum when adding Accumulator’s 1 to P is
always even.
2.2.6
Registers R0~R7
General purpose 8-bit registers that are locked in the lower portion of internal data area.
2.2.7
Data pointer register
Data Pointer Register is 16-bit wide which consists of two-8bit registers, DPH and DPL. This
register is used as a data pointer for the data transmission with external data memory in the
PSD module.
Figure 8.
PSW (Program Status Word) register
MSB
PSW
CY AC FO RS1 RS0 OV
LSB
P Reset Value 00h
Parity Flag
Carry Flag
Auxillary Carry Flag
Bit not assigned
General Purpose Flag
Overflow Flag
Register Bank Select Flags
(to select Bank0-3)
AI06639
18/181
UPSD3212A, UPSD3212C, UPSD3212CV
2.3
Architecture overview
Program memory
The program memory consists of two Flash memories: the main Flash memory (64 Kbit)
and the Secondary Flash memory (16 Kbit). The Flash memory can be mapped to any
address space as defined by the user in the PSDsoft Tool. It can also be mapped to Data
memory space during Flash memory update or programming.
After reset, the CPU begins execution from location 0000h. As shown in Figure 9, each
interrupt is assigned a fixed location in Program Memory. The interrupt causes the CPU to
jump to that location, where it commences execution of the service routine. External
Interrupt 0, for example, is assigned to location 0003h. If External Interrupt 0 is going to be
used, its service routine must begin at location 0003h. If the interrupt is not going to be
used, its service location is available as general purpose Program Memory.
The interrupt service locations are spaced at 8-byte intervals: 0003h for External Interrupt 0,
000Bh for Timer 0, 0013h for External Interrupt 1, 001Bh for Timer 1 and so forth. If an
interrupt service routine is short enough (as is often the case in control applications), it can
reside entirely within that 8-byte interval. Longer service routines can use a jump instruction
to skip over subsequent interrupt locations, if other interrupts are in use.
2.4
Data memory
The internal data memory is divided into four physically separated blocks: 256 bytes of
internal RAM, 128 bytes of Special Function Registers (SFRs) areas and 2 Kbytes (XRAMPSD) in the PSD module.
2.5
RAM
Four register banks, each 8 registers wide, occupy locations 0 through 31 in the lower RAM
area. Only one of these banks may be enabled at a time. The next 16 bytes, locations 32
through 47, contain 128 directly addressable bit locations. The stack depth is only limited by
the available internal RAM space of 256 bytes.
Figure 9.
Interrupt location of program memory
Interrupt
Location
•
•
•
•
•
008Bh
•
•
•
•
0013h
8 Bytes
000Bh
0003h
Reset
0000h
AI06640
19/181
Architecture overview
2.6
UPSD3212A, UPSD3212C, UPSD3212CV
XRAM-PSD
The 2 Kbytes of XRAM-PSD resides in the PSD module and can be mapped to any address
space through the DPLD (Decoding PLD) as defined by the user in PSDsoft Development
tool.
2.7
SFR
The SFRs can only be addressed directly in the address range from 80h to FFh. Table 15
gives an overview of the Special Function Registers. Sixteen address in the SFRs space are
both-byte and bit-addressable. The bit-addressable SFRs are those whose address ends in
0h and 8h. The bit addresses in this area are 80h to FFh.
Table 3.
RAM address
Byte address
(in hexadecimal)
Byte address
(in decimal)
¯
¯
FFh
255
30h
48
MSB
2Fh
7E
7D
7C
7B
LSB
7A
79
78
47
2Eh
77
76
75
74
73
72
71
70
46
2Dh
6F
6E
6D
6C
6B
6A
69
68
45
2Ch
67
66
65
64
63
62
61
60
44
2Bh
5F
5E
5D
5C
5B
5A
59
58
43
2Ah
57
56
55
54
53
52
51
50
42
29h
4F
4E
4D
4C
4B
4A
49
48
41
28h
47
46
45
44
43
42
41
40
40
27h
3F
3E
3D
3C
3B
3A
39
38
39
26h
37
36
35
34
33
32
31
30
38
25h
2F
2E
2D
2C
2B
2A
29
28
37
24h
27
26
25
24
23
22
21
20
36
23h
1F
1E
1D
1C
1B
1A
19
18
35
22h
17
16
15
14
13
12
11
10
34
21h
0F
0E
0D
0C
0B
0A
09
08
33
20h
07
06
05
04
03
02
01
00
32
1Fh
18h
17h
10h
0Fh
08h
07h
00h
20/181
7F
Bit address (hex)
Register bank 3
Register bank 2
Register bank 1
Register bank 0
31
24
23
16
15
8
7
0
UPSD3212A, UPSD3212C, UPSD3212CV
2.8
Architecture overview
Addressing modes
The addressing modes in UPSD321xx devices instruction set are as follows
1.
2.8.1
Direct addressing
2.
Indirect addressing
3.
Register addressing
4.
Register-specific addressing
5.
Immediate constants addressing
6.
Indexed addressing
Direct addressing
In a direct addressing the operand is specified by an 8-bit address field in the instruction.
Only internal Data RAM and SFRs (80~FFH RAM) can be directly addressed.
Example:
mov A, 3EH ; A 50ns)
Required
Start/Stop Hold
Time
Note
00h
1EA
50ns
When Bit 7 (enable bit) = 0, the number of
sample clock is 1EA (ignore Bit 6 to Bit 0)
80h
1EA
50ns
81h
2EA
100ns
82h
3EA
150ns
...
...
...
8Bh
12EA
600ns
...
...
...
FFh
128EA
6000ns
Fast mode I²C Start/Stop hold time
specification
I2C interface
UPSD3212A, UPSD3212C, UPSD3212CV
Table 59.
System clock setup examples
System Clock
S1SETUP,
S2SETUP
Register Value
Number of
Sample Clock
Required Start/Stop Hold
Time
40MHz (fOSC/2 -> 50ns)
8Bh
12 EA
600ns
30MHz (fOSC/2 -> 66.6ns)
89h
9 EA
600ns
20MHz (fOSC/2 -> 100ns)
86h
6 EA
600ns
8MHz (fOSC/2 -> 250ns)
83h
3 EA
750ns
87/181
USB hardware
16
UPSD3212A, UPSD3212C, UPSD3212CV
USB hardware
The characteristics of USB hardware are as follows:
●
Complies with the Universal Serial Bus specification Rev. 1.1
●
Integrated SIE (Serial Interface Engine), FIFO memory and transceiver
●
Low speed (1.5Mbit/s) device capability
●
Supports control endpoint0 and interrupt endpoint1 and 2
●
USB clock input must be 6MHz (requires MCU clock frequency to be 12, 24, or
36MHz).
The analog front-end is an on-chip generic USB transceiver. It is designed to allow voltage
levels equal to VDD from the standard logic to interface with the physical layer of the
Universal Serial Bus. It is capable of receiving and transmitting serial data at low speed
(1.5Mb/s).
The SIE is the digital-front-end of the USB block. This module recovers the 1.5MHz clock,
detects the USB sync word and handles all low-level USB protocols and error checking. The
bit-clock recovery circuit recovers the clock from the incoming USB data stream and is able
to track jitter and frequency drift according to the USB specification. The SIE also translates
the electrical USB signals into bytes or signals. Depending upon the device USB address
and the USB endpoint.
Address, the USB data is directed to the correct endpoint on SIE interface. The data transfer
of this H/W could be of type control or interrupt.
The device’s USB address and the enabling of the endpoints are programmable in the SIE
configuration header.
16.1
USB related registers
The USB block is controlled via seven registers in the memory: (UADR, UCON0, UCON1,
UCON2, UISTA, UIEN, and USTA).
Three memory locations on chip which communicate the USB block are:
●
USB endpoint0 data transmit register (UDT0)
●
USB endpoint0 data receive register (UDR0)
●
USB endpoint1 data transmit register (UDT1)
Table 60.
88/181
USB address register (UADR: 0EEh)
7
6
5
4
3
2
1
0
USBEN
UADD6
UADD5
UADD4
UADD3
UADD2
UADD1
UADD0
UPSD3212A, UPSD3212C, UPSD3212CV
Table 61.
Bit
USB hardware
Description of the UADR Bits
Symbol
R/W
Function
7
USBEN
R/W
USB Function Enable Bit.
When USBEN is clear, the USB module will not respond to
any tokens from host.
RESET clears this bit.
6 to 0
UADD6 to
UADD0
R/W
Specify the USB address of the device.
RESET clears these bits.
Table 62.
USB interrupt enable register (UIEN: 0E9h)
7
6
5
4
3
2
1
0
SUSPNDI
RSTE
RSTFIE
TXD0IE
RXD0IE
TXD1IE
EOPIE
RESUMI
Table 63.
Description of the UIEN bits
Bit
Symbol
R/W
7
SUSPNDI
R/W
Enable SUSPND Interrupt
6
RSTE
R/W
Enable USB Reset; also resets the CPU and PSD modules
when bit is set to '1.'
5
RSTFIE
R/W
Enable RSTF (USB Bus Reset Flag) Interrupt
4
TXD0IE
R/W
Enable TXD0 Interrupt
3
RXD0IE
R/W
Enable RXD0 Interrupt
2
TXD1IE
R/W
Enable TXD1 Interrupt
1
EOPIE
R/W
Enable EOP Interrupt
0
RESUMI
R/W
Enable USB Resume Interrupt when it is the Suspend mode
Table 64.
Function
USB interrupt status register (UISTA: 0E8h)
7
6
5
4
3
2
1
0
SUSPND
—
RSTF
TXD0F
RXD0F
TXD1F
EOPF
RESUMF
Table 65.
Bit
Description of the UISTA bits
Symbol
R/W
Function
USB Suspend Mode Flag.
To save power, this bit should be set if a 3ms constant idle
state is detected on USB bus. Setting this bit stops the clock to
the USB and causes the USB module to enter Suspend mode.
Software must clear this bit after the Resume flag (RESUMF)
is set while this Resume Interrupt Flag is serviced
7
SUSPND
R/W
6
—
—
Reserved
R
USB Reset Flag.
This bit is set when a valid RESET signal state is detected on
the D+ and D- lines. When the RSTE bit in the UIEN Register
is set, this reset detection will also generate an internal reset
signal to reset the CPU and other peripherals including the
USB module.
5
RSTF
89/181
USB hardware
UPSD3212A, UPSD3212C, UPSD3212CV
Table 65.
Bit
4
3
2
1
0
Table 66.
90/181
Description of the UISTA bits (continued)
Symbol
TXD0F
RXD0F
TXD1F
EOPF
RESUMF
R/W
Function
R/W
Endpoint0 Data Transmit Flag.
This bit is set after the data stored in Endpoint 0 transmit
buffers has been sent and an ACK handshake packet from the
host is received. Once the next set of data is ready in the
transmit buffers, software must clear this flag. To enable the
next data packet transmission, TX0E must also be set. If
TXD0F Bit is not cleared, a NAK handshake will be returned in
the next IN transactions. RESET clears this bit.
R/W
Endpoint0 Data Receive Flag.
This bit is set after the USB module has received a data
packet and responded with ACK handshake packet. Software
must clear this flag after all of the received data has been
read. Software must also set RX0E Bit to one to enable the
next data packet reception. If RXD0F Bit is not cleared, a NAK
handshake will be returned in the next OUT transaction.
RESET clears this bit.
R/W
Endpoint1 / Endpoint2 Data Transmit Flag.
This bit is shared by Endpoints 1 and Endpoints 2. It is set
after the data stored in the shared Endpoint 1/ Endpoint 2
transmit buffer has been sent and an ACK handshake packet
from the host is received. Once the next set of data is ready in
the transmit buffers, software must clear this flag. To enable
the next data packet transmission, TX1E must also be set. If
TXD1F Bit is not cleared, a NAK handshake will be returned in
the next IN transaction. RESET clears this bit.
R/W
End of Packet Flag.
This bit is set when a valid End of Packet sequence is
detected on the D+ and D-line. Software must clear this flag.
RESET clears this bit.
R/W
Resume Flag.
This bit is set when USB bus activity is detected while the
SUSPND Bit is set.
Software must clear this flag. RESET clears this bit.
USB Endpoint0 transmit control register (UCON0: 0EAh)
7
6
5
4
3
2
1
0
TSEQ0
STALL0
TX0E
RX0E
TP0SIZ3
TP0SIZ2
TP0SIZ1
TP0SIZ0
UPSD3212A, UPSD3212C, UPSD3212CV
Table 67.
Bit
7
6
5
USB hardware
Description of the UCON0 bits
Symbol
TSEQ0
STALL0
TX0E
R/W
Function
R/W
Endpoint0 Data Sequence Bit. (0=DATA0, 1=DATA1)
This bit determines which type of data packet (DATA0 or
DATA1) will be sent during the next IN transaction. Toggling of
this bit must be controlled by software. RESET clears this bit
R/W
Endpoint0 Force Stall Bit.
This bit causes Endpoint 0 to return a STALL handshake when
polled by either an IN or OUT token by the USB Host
Controller. The USB hardware clears this bit when a SETUP
token is received. RESET clears this bit.
R/W
Endpoint0 Transmit Enable.
This bit enables a transmit to occur when the USB Host
Controller sends an IN token to Endpoint 0. Software should
set this bit when data is ready to be transmitted. It must be
cleared by software when no more Endpoint 0 data needs to
be transmitted. If this bit is '0' or the TXD0F is set, the USB will
respond with a NAK handshake to any Endpoint 0 IN tokens.
RESET clears this bit.
4
RX0E
R/W
Endpoint0 receive enable.
This bit enables a receive to occur when the USB Host
Controller sends an OUT token to Endpoint 0. Software should
set this bit when data is ready to be received. It must be
cleared by software when data cannot be received. If this bit is
'0' or the RXD0F is set, the USB will respond with a NAK
handshake to any Endpoint 0 OUT tokens. RESET clears this
bit.
3 to 0
TP0SIZ3
to
TP0SIZ0
R/W
The number of transmit data bytes. These bits are cleared by
RESET.
Table 68.
USB Endpoint1 (and 2) transmit control register (UCON1: 0EBh)
7
6
5
4
3
2
1
0
TSEQ1
EP12SEL
TX1E
FRESUM
TP1SIZ3
TP1SIZ2
TP1SIZ1
TP1SIZ0
91/181
USB hardware
UPSD3212A, UPSD3212C, UPSD3212CV
Table 69.
Bit
7
6
5
Symbol
TSEQ1
EP12SEL
TX1E
R/W
Function
R/W
Endpoint 1/ Endpoint 2 Transmit Data Packet PID. (0=DATA0,
1=DATA1) This bit determines which type of data packet
(DATA0 or DATA1) will be sent during the next IN transaction
directed to Endpoint 1 or Endpoint 2.
Toggling of this bit must be controlled by software. RESET
clears this bit.
R/W
Endpoint 1/ Endpoint 2 Transmit Selection. (0=Endpoint 1,
1=Endpoint 2)
This bit specifies whether the data inside the registers UDT1
are used for Endpoint 1 or Endpoint 2. If all the conditions for a
successful Endpoint 2 USB response to a hosts IN token are
satisfied (TXD1F=0, TX1E=1, STALL2=0, and EP2E=1)
except that the EP12SEL Bit is configured for Endpoint 1, the
USB responds with a NAK handshake packet. RESET clears
this bit.
R/W
Endpoint1 / Endpoint2 Transmit Enable.
This bit enables a transmit to occur when the USB Host
Controller send an IN token to Endpoint 1 or Endpoint 2. The
appropriate endpoint enable bit, EP1E or EP2E Bit in the
UCON2 register, should also be set. Software should set the
TX1E Bit when data is ready to be transmitted. It must be
cleared by software when no more data needs to be
transmitted. If this bit is '0' or TXD1F is set, the USB will
respond with a NAK handshake to any Endpoint 1 or Endpoint
2 directed IN token.
RESET clears this bit.
4
FRESUM
R/W
Force Resume.
This bit forces a resume state (“K” on non-idle state) on the
USB data lines to initiate a remote wake-up. Software should
control the timing of the forced resume to be between 10ms
and 15ms. Setting this bit will not cause the RESUMF Bit to
set.
3 to 0
TP1SIZ3
to
TP1SIZ0
R/W
The number of transmit data bytes. These bits are cleared by
RESET.
Table 70.
USB control register (UCON2: 0ECh)
7
6
5
4
3
2
1
0
—
—
—
SOUT
EP2E
EP1E
STALL2
STALL1
Table 71.
92/181
Description of the UCON1 bits
Description of the UCON2 bits
Bit
Symbol
R/W
Function
7 to 5
—
—
4
SOUT
R/W
Status out is used to automatically respond to the OUT of a
control READ transfer
3
EP2E
R/W
Endpoint2 enable. RESET clears this bit
Reserved
UPSD3212A, UPSD3212C, UPSD3212CV
Table 71.
USB hardware
Description of the UCON2 bits (continued)
Bit
Symbol
R/W
2
EP1E
R/W
Endpoint1 enable. RESET clears this bit
1
STALL2
R/W
Endpoint2 Force Stall Bit. RESET clears this bit
0
STALL1
R/W
Endpoint1 Force Stall Bit. RESET clears this bit
Table 72.
Function
USB Endpoint0 status register (USTA: 0EDh)
7
6
5
4
3
2
1
0
RSEQ
SETUP
IN
OUT
RP0SIZ3
RP0SIZ2
RP0SIZ1
RP0SIZ0
Table 73.
Description of the USTA bits
Bit
Symbol
R/W
7
RSEQ
R/W
Endpoint0 receive data packet PID. (0=DATA0, 1=DATA1)
This bit will be compared with the type of data packet last
received for Endpoint0
6
SETUP
R
SETUP Token Detect Bit. This bit is set when the received
token packet is a SEPUP token, PID = b1101.
5
IN
R
IN Token Detect Bit.
This bit is set when the received token packet is an IN token.
4
OUT
R
OUT Token Detect Bit.
This bit is set when the received token packet is an OUT
token.
3 to 0
RP0SIZ3
to
RP0SIZ0
R
The number of data bytes received in a DATA packet
Table 74.
Function
USB Endpoint0 data receive register (UDR0: 0EFh)
7
6
5
4
3
2
1
0
UDR0.7
UDR0.6
UDR0.5
UDR0.4
UDR0.3
UDR0.2
UDR0.1
UDR0.0
Table 75.
USB Endpoint0 data transmit register (UDT0: 0E7h)
7
6
5
4
3
2
1
0
UDT0.7
UDT0.6
UDT0.5
UDT0.4
UDT0.3
UDT0.2
UDT0.1
UDT0.0
Table 76.
USB Endpoint1 data transmit register (UDT1: 0E6h)
7
6
5
4
3
2
1
0
UDT1.7
UDT1.6
UDT1.5
UDT1.4
UDT1.3
UDT1.2
UDT1.1
UDT1.0
The USCL 8-bit prescaler register for USB is at E1h. The USCL should be loaded with a
value that results in a clock rate of 6 MHz for the USB using the following formula:
USB clock input = (fOSC / 2) / (Prescaler register value +1)
Where fOSC is the MCU clock input frequency.
Note:
USB works ONLY with the MCU Clock frequencies of 12, 24, or 36 MHz. The Prescaler
values for these frequencies are 0, 1, and 2.
93/181
USB hardware
Table 77.
SFR
Reg
Add
Name
r
UPSD3212A, UPSD3212C, UPSD3212CV
USB SFR memory map
Bit Register Name
7
6
5
4
3
Reset
2
1
E1
USCL
E6
UDT1
UDT1.7
UDT1.6 UDT1.5 UDT1.4 UDT1.3 UDT1.2 UDT1.1
E7
UDT0
UDT0.7
UDT0.6 UDT0.5 UDT0.4 UDT0.3 UDT0.2 UDT0.1
E8
UISTA
SUSPND
—
E9
UIEN
SUSPNDI
E
RSTE
EA UCON0
0
value
Comments
00
8-bit
Prescaler
for USB
logic
UDT1.0
00
USB
Endpt1
Data Xmit
UDT0.0
00
USB
Endpt0
Data Xmit
RXD1F
EOPF
RESUMF
00
USB
Interrupt
Status
RSTFIE TXD0IE RXD0IE TXD1IE
EOPIE
RESUMI
E
00
USB
Interrupt
Enable
00
USB
Endpt0
Xmit
Control
00
USB
Endpt1
Xmit
Control
STALL1
00
USB
Control
Register
RP0SIZ3 RP0SIZ2 RP0SIZ1 RP0SIZ0
00
USB
Endpt0
Status
RSTF
TX0E
TXD0F
TSEQ0
STALL0
RX0E
EB UCON1
TSEQ1
EP12SE
L
—
EC UCON2
—
—
—
SOUT
RXD0F
TP0SIZ3 TP0SIZ2 TP0SIZ1 TP0SIZ0
FRESU
TP1SIZ3 TP1SIZ2 TP1SIZ1 TP1SIZ0
M
EP2E
EP1E
STALL2
ED
USTA
RSEQ
SETUP
IN
OUT
EE
UADR
USBEN
UADD6
UADD5
UADD4
UADD0
00
USB
Address
Register
EF
UDR0
UDR0.7
UDR0.6 UDR0.5 UDR0.4 UDR0.3 UDR0.2 UDR0.1 UDR0.0
00
USB
Endpt0
Data Recv
UADD3
16.2
Transceiver
16.2.1
USB physical layer characteristics
UADD2
UADD1
The following section describes the UPSD321xx devices compliance to the Chapter 7
Electrical section of the USB Specification, Revision 1.1. The section contains all signaling,
and physical layer specifications necessary to describe a low speed USB function.
94/181
UPSD3212A, UPSD3212C, UPSD3212CV
16.2.2
USB hardware
Low speed driver characteristics
The UPSD321xx devices use a differential output driver to drive the Low Speed USB data
signal onto the USB cable. The output swings between the differential high and low state are
well balanced to minimize signal skew. The slew rate control on the driver minimizes the
radiated noise and cross talk on the USB cable. The driver’s outputs support three-state
operation to achieve bi-directional half duplex operation. The UPSD321xx devices driver
tolerates a voltage on the signal pins of -0.5 V to 3.6 V with respect to local ground
reference without damage. The driver tolerates this voltage for 10.0µs while the driver is
active and driving, and tolerates this condition indefinitely when the driver is in its high
impedance state.
A low speed USB connection is made through an unshielded, untwisted wire cable a
maximum of 3 meters in length. The rise and fall time of the signals on this cable are well
controlled to reduce RFI emissions while limiting delays, signaling skews and distortions.
The UPSD321xx devices driver reaches the specified static signal levels with smooth rise
and fall times, resulting in segments between low speed devices and the ports to which they
are connected.
Figure 39. Low speed driver signal waveforms
One Bit
Time
1.5 Mb/s
VSE(max)
Driver
Signal Pins
Signal pins
pass output
spec levels
with minimal
reflections and
ringing
VSE(min)
VSS
AI06629
16.3
Receiver characteristics
UPSD321xx devices have a differential input receiver which is able to accept the USB data
signal. The receiver features an input sensitivity of at least 200 mV when both differential
data inputs are in the range of at least 0.8 V to 2.5 V with respect to its local ground
reference. This is the common mode range, as shown in Figure 40. The receiver tolerates
static input voltages between -0.5 V to 3.8 V with respect to its local ground reference
without damage. In addition to the differential receiver, there is a single-ended receiver for
each of the two data lines. The single-ended receivers have a switching threshold between
0.8 V and 2.0 V (TTL inputs).
95/181
USB hardware
UPSD3212A, UPSD3212C, UPSD3212CV
Minimum Differential Sensitivity (volts)
Figure 40. Differential input sensitivity over entire common mode range
1.0
0.8
0.6
0.4
0.2
0.0
0.0
16.4
0.2
0.4
0.6
0.8
1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4
Common Mode Input Voltage (volts)
2.6
2.8
3.0
3.2
AI06630
External USB pull-up resistor
The USB system specifies a pull-up resistor on the D- pin for low-speed peripherals. The
USB Spec 1.1 describes a 1.5 kΩ pull-up resistor to a 3.3 V supply. An approved alternative
method is a 7.5 kΩ pull-up to the USB VCC supply. This alternative is defined for low-speed
devices with an integrated cable. The chip is specified for the 7.5 kΩ pull-up. This eliminates
the need for an external 3.3 V regulator, or for a pin dedicated to providing a 3.3 V output
from the chip.
Figure 41. USB data signal timing and voltage levels
tR
VOH
tF
D+
90%
90%
VCR
VOL
10%
10%
D-
AI06631
Figure 42. Receiver jitter tolerance
TPERIOD
Differential
Data Lines
TJR
TJR1
TJR2
Consecutive
Transitions
N*TPERIOD+TJR1
Paired
Transitions
N*TPERIOD+TJR2
96/181
AI06632
UPSD3212A, UPSD3212C, UPSD3212CV
USB hardware
Figure 43. Differential to EOP transition skew and EOP width
TPERIOD
Crossover
Point Extended
Crossover
Point
Differential
Data Lines
Diff. Data to
SE0 Skew
N*TPERIOD+TDEOP
Source EOP Width: TEOPT
Receiver EOP Width
TEOPR1, TEOPR2
Figure 44. Differential data jitter
TPERIOD
Crossover
Points
Differential
Data Lines
Consecutive
Transitions
N*TPERIOD+TxJR1
Paired
Transitions
N*TPERIOD+TxJR2
AI06634
Table 78.
Symb
Transceiver DC characteristics
Parameter
Test Conditions(1)
Min
Max
Unit
VOH
Static Output High
15 kΩ ± 5% to GND(2,3)
2.8
3.6
V
VOL
Static Output Low
Notes 2, 3
—
0.3
V
VDI
Differential Input Sensitivity
|(D+) - (D-)|, Figure 42
0.2
—
V
VCM
Differential Input Common
mode
Figure 42
0.8
2.5
V
VSE
Single Ended Receiver
Threshold
—
0.8
2.0
V
CIN
Transceiver Capacitance
—
—
20
pF
IIO
Data Line (D+, D-) Leakage
0 < (D+,D-) < 3.3
–10
10
µA
7.5 kΩ ± 2% to VCC
7.35
7.65
kΩ
15 kΩ ± 5%
14.25
15.75
kΩ
RPU
External Bus Pull-up
Resistance, D-
RPD
External Bus Pull-down
Resistance
1. VCC = 5 V ± 10%; VSS = 0 V; TA = 0 to 70°C.
2. Level guaranteed for range of VCC = 4.5 V to 5.5 V.
3. With RPU, external idle resistor, 7.5 κ±2%, D- to VCC.
97/181
USB hardware
UPSD3212A, UPSD3212C, UPSD3212CV
Table 79.
Symb
tDRATE
Transceiver AC characteristics
Parameter
Low Speed Data Rate
Test Conditions(1)
Min
Max
Unit
Ave. bit rate (1.5Mb/s ±
1.5%)
1.4775
1.5225
Mbit/s
To next transition,
Figure 42(5)
–75
75
ns
For paired transition,
Figure 42(5)
–45
45
ns
Figure 43(5)
–40
100
ns
tDJR1
Receiver Data Jitter Tolerance
tDJR2
Differential Input Sensitivity
tDEOP
Differential to EOP Transition
Skew
tEOPR1
EOP Width at Receiver
Rejects as EOP(5,6)
165
—
ns
EOP Width at Receiver
EOP(5)
675
—
ns
—
–1.25
1.50
µs
tEOPR2
Accepts as
tEOPT
Source EOP Width
tUDJ1
Differential Driver Jitter
To next transition,
Figure 44
–95
95
ns
tUDJ2
Differential Driver Jitter
To paired transition,
Figure 44
–150
150
ns
tR
USB Data Transition Rise Time
Notes 2, 3, 4
75
300
ns
tF
USB Data Transition Fall Time
Notes 2, 3, 4
75
300
ns
tRFM
Rise/Fall Time Matching
t R / tF
80
120
%
VCRS
Output Signal Crossover
Voltage
—
1.3
2.0
V
1. VCC = 5 V ± 10%; VSS = 0 V; TA = 0 to 70°C.
2. Level guaranteed for range of VCC = 4.5 V to 5.5 V.
3. With RPU, external idle resistor, 7.5κ±2%, D- to VCC.
4. CL of 50 pF (75 ns) to 350 pF (300 ns).
5. Measured at crossover point of differential data signals.
6. USB specification indicates 330 ns.
98/181
UPSD3212A, UPSD3212C, UPSD3212CV
17
PSD module
PSD module
The PSD module provides configurable Program and Data memories to the 8032 CPU core
(MCU). In addition, it has its own set of I/O ports and a PLD with 16 macrocells for general
logic implementation.
Ports A,B,C, and D are general purpose programmable I/O ports that have a port
architecture which is different from the I/O ports in the MCU module.
The PSD module communicates with the MCU module through the internal address, data
bus (A0-A15, D0-D7) and control signals (RD, WR, PSEN, ALE, RESET). The user defines
the Decoding PLD in the PSDsoft Development Tool and can map the resources in the PSD
module to any program or data address space. Figure 45 shows the functional blocks in the
PSD module.
17.1
Functional overview
●
512 Kbit Flash memory. This is the main Flash memory. It is divided into four equalsized blocks (16 Kbytes each) that can be accessed with user-specified addresses.
●
Secondary 128 Kbit Flash boot memory. It is divided into two equal-sized blocks (8
Kbytes each) thatat can be accessed with user-specified addresses. This secondary
memory brings the ability to execute code and update the main Flash concurrently.
●
16 Kbit SRAM.
●
CPLD with 16 Output Micro Cells (OMCs} and up to 20 Input Micro Cells (IMCs). The
CPLD may be used to efficiently implement a variety of logic functions for internal and
external control. Examples include state machines, loadable shift registers, and
loadable counters.
●
Decode PLD (DPLD) that decodes address for selection of memory blocks in the PSD
module.
●
Configurable I/O ports (Port A,B,C and D) that can be used for the following functions:
–
MCU I/Os
–
PLD I/Os
–
Latched MCU address output
–
Special function I/Os
–
I/O ports may be configured as open-drain outputs
●
Built-in JTAG compliant serial port allows full-chip In-System Programmability (ISP).
With it, you can program a blank device or reprogram a device in the factory or the field.
●
Internal page register that can be used to expand the 8032 MCU module address
space by a factor of 256.
●
Internal programmable Power Management Unit (PMU) that supports a low-power
mode called Power-down mode. The PMU can automatically detect a lack of the 8032
CPU core activity and put the PSD module into Power-down mode.
●
Erase/WRITE cycles:
Flash memory - 100,000 minimum
PLD - 1,000 minimum
Data Retention: 15 year minimum (for Main Flash memory, Boot, PLD and
Configuration bits)
99/181
PSD module
UPSD3212A, UPSD3212C, UPSD3212CV
73
PD1 – PD2
JTAG
SERIAL
CHANNEL
PLD, CONFIGURATION
& FLASH MEMORY
LOADER
CLKIN
MACROCELL FEEDBACK OR PORT INPUT
PORT A ,B & C
CLKIN
73
PORT
D
PROG.
PORT
PC0 – PC7
PORT
C
PROG.
PORT
PB0 – PB7
PORT
B
20 INPUT MACROCELLS
PROG.
PORT
PORT A ,B & C
FLASH ISP CPLD
(CPLD)
2 EXT CS TO PORT D
RUNTIME CONTROL
AND I/O REGISTERS
16 OUTPUT MACROCELLS
PROG.
PORT
PORT
A
CSIOP
PERIP I/O MODE SELECTS
FLASH DECODE
PLD (DPLD)
SECTOR
SELECTS
128KBIT SECONDARY
NON-VOLATILE MEMORY
(BOOT OR DATA)
2 SECTORS
SECTOR
SELECTS
8 SECTORS
8
CLKIN
(PD1)
GLOBAL
CONFIG. &
SECURITY
BUS
Interface
D0 – D7
WR_, RD_,
PSEN_, ALE,
RESET_,
A0-A15
8032 Bus
BUS
Interface
PLD
INPUT
BUS
PAGE
REGISTER
EMBEDDED
ALGORITHM
ADDRESS/DATA/CONTROL BUS
512KBIT PRIMARY
FLASH MEMORY
POWER
MANGMT
UNIT
PA0 – PA7
VSTDBY
(PC2)
Figure 45. UPSD321xx PSD module block diagram
AI07431
17.2
In-system programming (ISP)
Using the JTAG signals on Port C, the entire PSD module device can be programmed or
erased without the use of the MCU. The primary Flash memory can also be programmed insystem by the MCU executing the programming algorithms out of the secondary memory, or
SRAM. The secondary memory can be programmed the same way by executing out of the
primary Flash memory. The PLD or other PSD module configuration blocks can be
programmed through the JTAG port or a device programmer. Table Table 80 indicates which
programming methods can program different functional blocks of the PSD module.
100/181
UPSD3212A, UPSD3212C, UPSD3212CV
Table 80.
PSD module
Methods of programming different functional blocks of the PSD module
Functional Block
JTAG programming Device programmer
IAP
Primary Flash memory
Yes
Yes
Yes
Secondary Flash memory
Yes
Yes
Yes
PLD array (DPLD and CPLD)
Yes
Yes
No
PSD module configuration
Yes
Yes
No
101/181
Development system
18
UPSD3212A, UPSD3212C, UPSD3212CV
Development system
UPSD321xx devices are supported by PSDsoft, a Windows-based software development
tool (Windows-95, Windows-98, Windows-NT). A PSD module design is quickly and easily
produced in a point and click environment. The designer does not need to enter Hardware
Description Language (HDL) equations, unless desired, to define PSD module pin functions
and memory map information. The general design flow is shown in Figure 46. PSDsoft is
available from our web site (the address is given on the back page of this data sheet) or
other distribution channels.
PSDsoft directly supports a low cost device programmer from ST: FlashLINK (JTAG). The
programmer may be purchased through your local distributor/representative. UPSD321xx
devices are also supported by third party device programmers. See our web site for the
current list.
Figure 46. PSDsoft express development tool
Choose µPSD
Define µPSD Pin and
Node Functions
Point and click definition of
PSD pin functions, internal nodes,
and MCU system memory map
Define General Purpose
Logic in CPLD
C Code Generation
Point and click definition of combinatorial and registered logic in CPLD.
Access HDL is available if needed
GENERATE C CODE
SPECIFIC TO PSD
FUNCTIONS
Merge MCU Firmware with
PSD Module Configuration
A composite object file is created
containing MCU firmware and
PSD configuration
MCU FIRMWARE
HEX OR S-RECORD
FORMAT
USER'S CHOICE OF
8032
COMPILER/LINKER
*.OBJ FILE
PSD Programmer
FlashLINK (JTAG)
*.OBJ FILE
AVAILABLE
FOR 3rd PARTY
PROGRAMMERS
AI05798
102/181
UPSD3212A, UPSD3212C, UPSD3212CV
19
PSD module register description and address offset
PSD module register description and address offset
Table 81 shows the offset addresses to the PSD module registers relative to the CSIOP
base address. The CSIOP space is the 256 bytes of address that is allocated by the user to
the internal PSD module registers. Table 81 provides brief descriptions of the registers in
CSIOP space. The following section gives a more detailed description.
Table 81.
Register address offset
Register Name
Port A Port B Port C Port D Other(1)
Reads Port pin as input, MCU I/O Input
mode
Data In
00
01
Control
02
03
Data Out
04
05
12
13
Stores data for output to Port pins,
MCU I/O Output mode
Direction
06
07
14
15
Configures Port pin as input or output
Drive Select
08
09
16
17
Configures Port pins as either CMOS
or Open Drain on some pins, while
selecting high slew rate on other pins.
Input Macrocell
0A
0B
18
Enable Out
0C
0D
1A
Output Macrocells
AB
20
20
Output Macrocells
BC
Mask Macrocells
AB
Mask Macrocells
BC
21
22
10
Description
11
Selects mode between MCU I/O or
Address Out
Reads Input Macrocells
Reads the status of the output enable
to the I/O Port driver
1B
READ – reads output of macrocells AB
WRITE – loads macrocell flip-flops
READ – reads output of macrocells BC
WRITE – loads macrocell flip-flops
21
Blocks writing to the Output Macrocells
AB
22
23
Blocks writing to the Output Macrocells
BC
23
Primary Flash
Protection
C0
Read-only – Primary Flash Sector
Protection
Secondary Flash
memory
Protection
C2
Read-only – PSD module Security and
Secondary Flash memory Sector
Protection
PMMR0
B0
Power Management Register 0
PMMR2
B4
Power Management Register 2
Page
E0
Page Register
VM
E2
Places PSD module memory areas in
Program and/or Data space on an
individual basis.
1. Other registers that are not part of the I/O ports.
103/181
PSD module detailed operation
20
UPSD3212A, UPSD3212C, UPSD3212CV
PSD module detailed operation
As shown in Figure 14, the PSD module consists of five major types of functional blocks:
●
Memory blocks
●
PLD blocks
●
I/O Ports
●
Power Management Unit (PMU)
●
JTAG Interface
The functions of each block are described in the following sections. Many of the blocks
perform multiple functions, and are user configurable.
104/181
UPSD3212A, UPSD3212C, UPSD3212CV
21
Memory blocks
Memory blocks
The PSD module has the following memory blocks:
●
Primary Flash memory
●
Secondary Flash memory
●
SRAM
The Memory Select signals for these blocks originate from the Decode PLD (DPLD) and are
user-defined in PSDsoft Express.
21.1
Primary Flash memory and secondary Flash memory
description
The primary Flash memory is divided evenly into four equal sectors. The secondary Flash
memory is divided into two equal sectors. Each sector of either memory block can be
separately protected from Program and Erase cycles.
Flash memory may be erased on a sector-by-sector basis. Flash sector erasure may be
suspended while data is read from other sectors of the block and then resumed after
reading.
During a Program or Erase cycle in Flash memory, the status can be output on Ready/Busy
(PC3). This pin is set up using PSDsoft Express Configuration.
21.2
Memory block select signals
The DPLD generates the Select signals for all the internal memory blocks (see Section 22:
PLDs). Each of the four sectors of the primary Flash memory has a Select signal (FS0-FS3)
which can contain up to three product terms. Each of the two sectors of the secondary Flash
memory has a Select signal (CSBOOT0-CSBOOT1) which can contain up to three product
terms. Having three product terms for each Select signal allows a given sector to be
mapped in Program or Data space.
21.2.1
Ready/Busy (PC3)
This signal can be used to output the Ready/Busy status of the Flash memory. The output
on Ready/Busy (PC3) is a '0' (Busy) when Flash memory is being written to, or when Flash
memory is being erased. The output is a '1' (Ready) when no WRITE or Erase cycle is in
progress.
21.2.2
Memory operation
The primary Flash memory and secondary Flash memory are addressed through the MCU
Bus. The MCU can access these memories in one of two ways:
●
The MCU can execute a typical bus WRITE or READ operation.
●
The MCU can execute a specific Flash memory instruction that consists of several
WRITE and READ operations. This involves writing specific data patterns to special
addresses within the Flash memory to invoke an embedded algorithm. These
instructions are summarized in Table 82.
105/181
Memory blocks
UPSD3212A, UPSD3212C, UPSD3212CV
Typically, the MCU can read Flash memory using READ operations, just as it would read a
ROM device. However, Flash memory can only be altered using specific Erase and Program
instructions. For example, the MCU cannot write a single byte directly to Flash memory as it
would write a byte to RAM. To program a byte into Flash memory, the MCU must execute a
Program instruction, then test the status of the Program cycle. This status test is achieved
by a READ operation or polling Ready/Busy (PC3).
21.3
Instructions
An instruction consists of a sequence of specific operations. Each received byte is
sequentially decoded by the PSD module and not executed as a standard WRITE operation.
The instruction is executed when the correct number of bytes are properly received and the
time between two consecutive bytes is shorter than the time-out period. Some instructions
are structured to include READ operations after the initial WRITE operations.
The instruction must be followed exactly. Any invalid combination of instruction bytes or
time-out between two consecutive bytes while addressing Flash memory resets the device
logic into READ mode (Flash memory is read like a ROM device).
The Flash memory supports the instructions summarized in Table 82:
●
Erase memory by chip or sector
●
Suspend or resume sector erase
●
Program a Byte
●
RESET to READ mode
●
Read Sector Protection Status
These instructions are detailed in Table 82. For efficient decoding of the instructions, the first
two bytes of an instruction are the coded cycles and are followed by an instruction byte or
confirmation byte. The coded cycles consist of writing the data AAh to address X555h
during the first cycle and data 55h to address XAAAh during the second cycle. Address
signals A15-A12 are Don’t Care during the instruction WRITE cycles. However, the
appropriate Sector Select (FS0-FS3 or CSBOOT0-CSBOOT1) must be selected.
The primary and secondary Flash memories have the same instruction set (except for Read
Primary Flash Identifier). The Sector Select signals determine which Flash memory is to
receive and execute the instruction. The primary Flash memory is selected if any one of
Sector Select (FS0-FS3) is High, and the secondary Flash memory is selected if any one of
Sector Select (CSBOOT0-CSBOOT1) is High.
Table 82.
Instructions
FS0-FS3 or
CSBOOT0CSBOOT1
Cycle 1
READ(5)
1
“Read”
RD @ RA
READ Sector
Protection(6,8,13)
1
AAh@
X555h
55h@
XAAAh
90h@
X555h
Read
status @
XX02h
Program a Flash
Byte(13)
1
AAh@
X555h
55h@
XAAAh
A0h@
X555h
PD@ PA
Instruction
106/181
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 6
Cycle 7
UPSD3212A, UPSD3212C, UPSD3212CV
Table 82.
Memory blocks
Instructions (continued)
Instruction
FS0-FS3 or
CSBOOT0CSBOOT1
Cycle 1
Cycle 2
Cycle 3
Cycle 4
Cycle 5
Cycle 6
Flash Sector
Erase(7,13)
1
AAh@
X555h
55h@
XAAAh
80h@
X555h
AAh@
X555h
55h@
XAAAh
30h@ SA
Flash Bulk
Erase(13)
1
AAh@
X555h
55h@
XAAAh
80h@
X555h
AAh@
X555h
55h@
XAAAh
10h@
X555h
Suspend Sector
Erase(11)
1
B0h@
XXXXh
Resume Sector
Erase(12)
1
30h@
XXXXh
RESET(6)
1
F0h@
XXXXh
Cycle 7
30h7@
next SA
1. All bus cycles are WRITE bus cycles, except the ones with the “Read” label
2. All values are in hexadecimal.
3. X = Don’t care. Addresses of the form XXXXh, in this table, must be even addresses
4. RA = Address of the memory location to be read
5. RD = Data READ from location RA during the READ cycle
6. PA = Address of the memory location to be programmed. Addresses are latched on the falling edge of
WRITE Strobe (WR, CNTL0).
7. PA is an even address for PSD in Word Programming mode.
8. PD = Data word to be programmed at location PA. Data is latched on the rising edge of WRITE Strobe
(WR, CNTL0)
9. SA = Address of the sector to be erased or verified. The Sector Select (FS0-FS3 or CSBOOT0-CSBOOT1)
of the sector to be erased, or verified, must be Active (High).
10. Sector Select (FS0-FS3 or CSBOOT0-CSBOOT1) signals are active High, and are defined in PSDsoft
Express.
11. Only address Bits A11-A0 are used in instruction decoding.
12. No Unlock or instruction cycles are required when the device is in the READ mode
13. The RESET instruction is required to return to the READ mode after reading the Sector Protection Status,
or if the Error flag bit (DQ5) goes High.
14. Additional sectors to be erased must be written at the end of the Sector Erase instruction within 80µs.
15. The data is 00h for an unprotected sector, and 01h for a protected sector. In the fourth cycle, the Sector
Select is active, and (A1,A0)=(1,0)
16. The system may perform READ and Program cycles in non-erasing sectors, read the Flash ID or read the
Sector Protection Status when in the Suspend Sector Erase mode. The Suspend Sector Erase instruction
is valid only during a Sector Erase cycle.
17. The Resume Sector Erase instruction is valid only during the Suspend Sector Erase mode.
18. The MCU cannot invoke these instructions while executing code from the same Flash memory as that for
which the instruction is intended. The MCU must retrieve, for example, the code from the secondary Flash
memory when reading the Sector Protection Status of the primary Flash memory.
21.4
Power-down instruction and Power-up mode
21.4.1
Power-up mode
The PSD module internal logic is reset upon Power-up to the READ mode. Sector Select
(FS0-FS3 and CSBOOT0-CSBOOT1) must be held Low, and WRITE Strobe (WR, CNTL0)
High, during Power-up for maximum security of the data contents and to remove the
107/181
Memory blocks
UPSD3212A, UPSD3212C, UPSD3212CV
possibility of a byte being written on the first edge of WRITE Strobe (WR, CNTL0). Any
WRITE cycle initiation is locked when VCC is below VLKO.
21.5
Read
Under typical conditions, the MCU may read the primary Flash memory or the secondary
Flash memory using READ operations just as it would a ROM or RAM device. Alternately,
the MCU may use READ operations to obtain status information about a Program or Erase
cycle that is currently in progress. Lastly, the MCU may use instructions to read special data
from these memory blocks. The following sections describe these READ functions.
21.5.1
Read memory contents
Primary Flash memory and secondary Flash memory are placed in the READ mode after
Power-up, chip reset, or a Reset Flash instruction (see Table 82). The MCU can read the
memory contents of the primary Flash memory or the secondary Flash memory by using
READ operations any time the READ operation is not part of an instruction.
21.5.2
Read memory sector protection status
The primary Flash memory Sector Protection Status is read with an instruction composed of
4 operations: 3 specific WRITE operations and a READ operation (see Table 82). During the
READ operation, address Bits A6, A1, and A0 must be '0,' '1,' and '0,' respectively, while
Sector Select (FS0-FS3 or CSBOOT0-CSBOOT1) designates the Flash memory sector
whose protection has to be verified. The READ operation produces 01h if the Flash memory
sector is protected, or 00h if the sector is not protected.
The sector protection status for all NVM blocks (primary Flash memory or secondary Flash
memory) can also be read by the MCU accessing the Flash Protection registers in PSD I/O
space. See Section 21.8.1: Flash memory sector protect for register definitions.
21.5.3
Reading the Erase/Program status bits
The Flash memory provides several status bits to be used by the MCU to confirm the
completion of an Erase or Program cycle of Flash memory. These status bits minimize the
time that the MCU spends performing these tasks and are defined in Table 83. The status
bits can be read as many times as needed.
For Flash memory, the MCU can perform a READ operation to obtain these status bits while
an Erase or Program instruction is being executed by the embedded algorithm. See
Section 21.6: Programming Flash memory, for details.
21.5.4
Data polling flag (DQ7)
When erasing or programming in Flash memory, the Data Polling flag bit (DQ7) outputs the
complement of the bit being entered for programming/writing on the DQ7 Bit. Once the
108/181
UPSD3212A, UPSD3212C, UPSD3212CV
Memory blocks
Program instruction or the WRITE operation is completed, the true logic value is read on the
Data Polling flag bit (DQ7) (in a READ operation).
21.5.5
●
Data Polling is effective after the fourth WRITE pulse (for a Program instruction) or after
the sixth WRITE pulse (for an Erase instruction). It must be performed at the address
being programmed or at an address within the Flash memory sector being erased.
●
During an Erase cycle, the Data Polling flag bit (DQ7) outputs a '0.' After completion of
the cycle, the Data Polling flag bit (DQ7) outputs the last bit programmed (it is a '1' after
erasing).
●
If the byte to be programmed is in a protected Flash memory sector, the instruction is
ignored.
●
If all the Flash memory sectors to be erased are protected, the Data Polling flag bit
(DQ7) is reset to '0' for about 100µs, and then returns to the previous addressed byte.
No erasure is performed.
Toggle flag (DQ6)
The Flash memory offers another way for determining when the Program cycle is
completed. During the internal WRITE operation and when either the FS0-FS3 or
CSBOOT0-CSBOOT1 is true, the Toggle flag bit (DQ6) toggles from '0' to '1' and '1' to '0' on
subsequent attempts to read any byte of the memory.
When the internal cycle is complete, the toggling stops and the data READ on the Data Bus
D0-D7 is the addressed memory byte. The device is now accessible for a new READ or
WRITE operation. The cycle is finished when two successive Reads yield the same output
data.
21.5.6
●
The Toggle flag bit (DQ6) is effective after the fourth WRITE pulse (for a Program
instruction) or after the sixth WRITE pulse (for an Erase instruction).
●
If the byte to be programmed belongs to a protected Flash memory sector, the
instruction is ignored.
●
If all the Flash memory sectors selected for erasure are protected, the Toggle flag bit
(DQ6) toggles to '0' for about 100µs and then returns to the previous addressed byte.
Error flag (DQ5)
During a normal Program or Erase cycle, the Error flag bit (DQ5) is to '0.' This bit is set to '1'
when there is a failure during Flash memory Byte Program, Sector Erase, or Bulk Erase
cycle.
In the case of Flash memory programming, the Error flag bit (DQ5) indicates the attempt to
program a Flash memory bit from the programmed state, '0', to the erased state, '1,' which is
not valid. The Error flag bit (DQ5) may also indicate a Time-out condition while attempting to
program a byte.
In case of an error in a Flash memory Sector Erase or Byte Program cycle, the Flash
memory sector in which the error occurred or to which the programmed byte belongs must
no longer be used. Other Flash memory sectors may still be used. The Error Flag bit (DQ5)
is reset after a Reset Flash instruction.
21.5.7
Erase time-out flag (DQ3)
The Erase Time-out Flag bit (DQ3) reflects the time-out period allowed between two
consecutive Sector Erase instructions. The Erase Time-out Flag bit (DQ3) is reset to '0' after
109/181
Memory blocks
UPSD3212A, UPSD3212C, UPSD3212CV
a Sector Erase cycle for a time period of 100µs + 20% unless an additional Sector Erase
instruction is decoded. After this time period, or when the additional Sector Erase instruction
is decoded, the Erase Time-out Flag bit (DQ3) is set to ‘1’.
Table 83.
Status bit
Functional Block
FS0-FS3/
CSBOOT0CSBOOT1
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
Flash Memory
VIH
Data
Polling
Toggle
Flag
Error
Flag
X
Erase
Time-out
X
X
X
1. X = Not guaranteed value, can be read either '1' or '0.'
2. DQ7-DQ0 represent the Data Bus bits, D7-D0.
3. FS0-FS3 and CSBOOT0-CSBOOT1 are active High.
21.6
Programming Flash memory
Flash memory must be erased prior to being programmed. A byte of Flash memory is
erased to all '1's (FFh), and is programmed by setting selected bits to '0'. The MCU may
erase Flash memory all at once or by-sector, but not byte-by-byte. However, the MCU may
program Flash memory byte-by-byte.
The primary and secondary Flash memories require the MCU to send an instruction to
program a byte or to erase sectors (see Table 82).
Once the MCU issues a Flash memory Program or Erase instruction, it must check for the
status bits for completion. The embedded algorithms that are invoked support several
means to provide status to the MCU. Status may be checked using any of three methods:
Data Polling, Data Toggle, or Ready/Busy (PC3).
21.6.1
Data Polling
Polling on the Data Polling Flag bit (DQ7) is a method of checking whether a Program or
Erase cycle is in progress or has completed. Figure 47 shows the Data Polling algorithm.
When the MCU issues a Program instruction, the embedded algorithm begins. The MCU
then reads the location of the byte to be programmed in Flash memory to check status. The
Data Polling Flag bit (DQ7) of this location becomes the complement of b7 of the original
data byte to be programmed. The MCU continues to poll this location, comparing the Data
Polling Flag bit (DQ7) and monitoring the Error Flag bit (DQ5). When the Data Polling Flag
bit (DQ7) matches b7 of the original data, and the Error Flag bit (DQ5) remains '0,' the
embedded algorithm is complete. If the Error Flag bit (DQ5) is '1,' the MCU should test the
Data Polling Flag bit (DQ7) again since the Data Polling Flag bit (DQ7) may have changed
simultaneously with the Error Flag bit (DQ5) (see Figure 47).
The Error Flag bit (DQ5) is set if either an internal time-out occurred while the embedded
algorithm attempted to program the byte or if the MCU attempted to program a '1' to a bit
that was not erased (not erased is logic '0').
It is suggested (as with all Flash memories) to read the location again after the embedded
programming algorithm has completed, to compare the byte that was written to the Flash
memory with the byte that was intended to be written.
110/181
UPSD3212A, UPSD3212C, UPSD3212CV
Memory blocks
When using the Data Polling method during an Erase cycle, Figure 47 still applies. However,
the Data Polling Flag bit (DQ7) is '0' until the Erase cycle is complete. A '1' on the Error Flag
bit (DQ5) indicates a time-out condition on the Erase cycle; a '0' indicates no error. The
MCU can read any location within the sector being erased to get the Data Polling Flag bit
(DQ7) and the Error Flag bit (DQ5).
PSDsoft Express generates ANSI C code functions which implement these Data Polling
algorithms.
Figure 47. Data polling flowchart
START
READ DQ5 & DQ7
at VALID ADDRESS
DQ7
=
DATA
YES
NO
NO
DQ5
=1
YES
READ DQ7
DQ7
=
DATA
YES
NO
FAIL
PASS
AI01369B
21.6.2
Data toggle
Checking the Toggle Flag bit (DQ6) is a method of determining whether a Program or Erase
cycle is in progress or has completed. Figure 48 shows the Data Toggle algorithm.
When the MCU issues a Program instruction, the embedded algorithm begins. The MCU
then reads the location of the byte to be programmed in Flash memory to check status. The
Toggle Flag bit (DQ6) of this location toggles each time the MCU reads this location until the
embedded algorithm is complete. The MCU continues to read this location, checking the
Toggle Flag bit (DQ6) and monitoring the Error Flag bit (DQ5). When the Toggle Flag bit
(DQ6) stops toggling (two consecutive reads yield the same value), and the Error Flag bit
(DQ5) remains '0,' the embedded algorithm is complete. If the Error Flag bit (DQ5) is '1,' the
MCU should test the Toggle Flag bit (DQ6) again, since the Toggle Flag bit (DQ6) may have
changed simultaneously with the Error Flag bit (DQ5) (see Figure 48).
The Error Flag bit (DQ5) is set if either an internal time-out occurred while the embedded
algorithm attempted to program the byte, or if the MCU attempted to program a '1' to a bit
that was not erased (not erased is logic '0').
It is suggested (as with all Flash memories) to read the location again after the embedded
programming algorithm has completed, to compare the byte that was written to Flash
memory with the byte that was intended to be written.
111/181
Memory blocks
UPSD3212A, UPSD3212C, UPSD3212CV
When using the Data Toggle method after an Erase cycle, Figure 48 still applies. the Toggle
Flag bit (DQ6) toggles until the Erase cycle is complete. A 1 on the Error Flag bit (DQ5)
indicates a time-out condition on the Erase cycle; a '0' indicates no error. The MCU can read
any location within the sector being erased to get the Toggle Flag bit (DQ6) and the Error
Flag bit (DQ5).
PSDsoft Express generates ANSI C code functions which implement these Data Toggling
algorithms.
Figure 48. Data toggle flowchart
START
READ
DQ5 & DQ6
DQ6
=
TOGGLE
NO
YES
NO
DQ5
=1
YES
READ DQ6
DQ6
=
TOGGLE
NO
YES
FAIL
PASS
AI01370B
21.7
Erasing Flash memory
21.7.1
Flash Bulk Erase
The Flash Bulk Erase instruction uses six WRITE operations followed by a READ operation
of the status register, as described in Table 82. If any byte of the Bulk Erase instruction is
wrong, the Bulk Erase instruction aborts and the device is reset to the READ Flash memory
status.
During a Bulk Erase, the memory status may be checked by reading the Error Flag bit
(DQ5), the Toggle Flag bit (DQ6), and the Data Polling Flag bit (DQ7), as detailed in
Section 21.6: Programming Flash memory. The Error Flag bit (DQ5) returns a '1' if there has
been an Erase Failure (maximum number of Erase cycles have been executed).
It is not necessary to program the memory with 00h because the PSD module automatically
does this before erasing to 0FFh.
During execution of the Bulk Erase instruction, the Flash memory does not accept any
instructions.
112/181
UPSD3212A, UPSD3212C, UPSD3212CV
21.7.2
Memory blocks
Flash Sector Erase
The Sector Erase instruction uses six WRITE operations, as described in Table 82.
Additional Flash Sector Erase codes and Flash memory sector addresses can be written
subsequently to erase other Flash memory sectors in parallel, without further coded cycles,
if the additional bytes are transmitted in a shorter time than the time-out period of about
100µs. The input of a new Sector Erase code restarts the time-out period.
The status of the internal timer can be monitored through the level of the Erase Time-out
Flag bit (DQ3). If the Erase Time-out Flag bit (DQ3) is '0,' the Sector Erase instruction has
been received and the time-out period is counting. If the Erase Time-out Flag bit (DQ3) is '1,'
the time-out period has expired and the embedded algorithm is busy erasing the Flash
memory sector(s). Before and during Erase time-out, any instruction other than Suspend
Sector Erase and Resume Sector Erase instructions abort the cycle that is currently in
progress, and reset the device to READ mode.
During a Sector Erase, the memory status may be checked by reading the Error Flag bit
(DQ5), the Toggle Flag bit (DQ6), and the Data Polling Flag bit (DQ7), as detailed in
Section 21.6: Programming Flash memory.
During execution of the Erase cycle, the Flash memory accepts only RESET and Suspend
Sector Erase instructions. Erasure of one Flash memory sector may be suspended, in order
to read data from another Flash memory sector, and then resumed.
21.7.3
Suspend Sector Erase
When a Sector Erase cycle is in progress, the Suspend Sector Erase instruction can be
used to suspend the cycle by writing 0B0h to any address when an appropriate Sector
Select (FS0-FS3 or CSBOOT0-CSBOOT1) is High. (See Table 82). This allows reading of
data from another Flash memory sector after the Erase cycle has been suspended.
Suspend Sector Erase is accepted only during an Erase cycle and defaults to READ mode.
A Suspend Sector Erase instruction executed during an Erase time-out period, in addition to
suspending the Erase cycle, terminates the time out period.
The Toggle Flag bit (DQ6) stops toggling when the internal logic is suspended. The status of
this bit must be monitored at an address within the Flash memory sector being erased. The
Toggle Flag bit (DQ6) stops toggling between 0.1µs and 15µs after the Suspend Sector
Erase instruction has been executed. The Flash memory is then automatically set to READ
mode.
If an Suspend Sector Erase instruction was executed, the following rules apply:
21.7.4
●
Attempting to read from a Flash memory sector that was being erased outputs invalid
data.
●
Reading from a Flash sector that was not being erased is valid.
●
The Flash memory cannot be programmed, and only responds to Resume Sector
Erase and Reset Flash instructions (READ is an operation and is allowed).
●
If a Reset Flash instruction is received, data in the Flash memory sector that was being
erased is invalid.
Resume Sector Erase
If a Suspend Sector Erase instruction was previously executed, the erase cycle may be
resumed with this instruction. The Resume Sector Erase instruction consists of writing 030h
113/181
Memory blocks
UPSD3212A, UPSD3212C, UPSD3212CV
to any address while an appropriate Sector Select (FS0-FS3 or CSBOOT0-CSBOOT1) is
High. (See Table 82.)
21.8
Specific features
21.8.1
Flash memory sector protect
Each primary and secondary Flash memory sector can be separately protected against
Program and Erase cycles. Sector Protection provides additional data security because it
disables all Program or Erase cycles. This mode can be activated through the JTAG Port or
a Device Programmer.
Sector protection can be selected for each sector using the PSDsoft Express Configuration
program. This automatically protects selected sectors when the device is programmed
through the JTAG Port or a Device Programmer. Flash memory sectors can be unprotected
to allow updating of their contents using the JTAG Port or a Device Programmer. The MCU
can read (but cannot change) the sector protection bits.
Any attempt to program or erase a protected Flash memory sector is ignored by the device.
The Verify operation results in a READ of the protected data. This allows a guarantee of the
retention of the Protection status.
The sector protection status can be read by the MCU through the Flash memory protection
registers (in the CSIOP block). See Table 84 and Table 85.
Table 84.
Sector protection/security bit definition – Flash protection register
Bit 7
Bit 6
Bit 5
Bit 4
Not used
Not used
Not used
Not used
1. Bit Definitions:
Sec_Prot
Sec_Prot
Table 85.
Bit 2
Bit 1
Bit 0
Sec3_Prot Sec2_Prot Sec1_Prot Sec0_Prot
1 = Primary Flash memory or secondary Flash memory Sector is write-protected.
0 = Primary Flash memory or secondary Flash memory Sector is not write-protected.
Sector protection/security bit definition – secondary Flash protection
register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Security_B
it
Not used
Not used
Not used
Not used
Not used
1. Bit Definitions:
Sec_Prot
Sec_Prot
Security_Bit
21.8.2
Bit 3
Bit 1
Bit 0
Sec1_Prot Sec0_Prot
1 = Secondary Flash memory Sector is write-protected.
0 = Secondary Flash memory Sector is not write-protected.
0 = Security Bit in device has not been set; 1 = Security Bit in device has been set.
Reset Flash
The Reset Flash instruction consists of one WRITE cycle (see Table 82). It can also be
optionally preceded by the standard two WRITE decoding cycles (writing AAh to 555h and
55h to AAAh). It must be executed after:
114/181
●
Reading the Flash Protection Status or Flash ID
●
An Error condition has occurred (and the device has set the Error Flag bit (DQ5) to '1'
during a Flash memory Program or Erase cycle.
UPSD3212A, UPSD3212C, UPSD3212CV
Memory blocks
The Reset Flash instruction puts the Flash memory back into normal READ mode. If an
Error condition has occurred (and the device has set the Error Flag bit (DQ5) to '1' the Flash
memory is put back into normal READ mode within a few milliseconds of the Reset Flash
instruction having been issued. The Reset Flash instruction is ignored when it is issued
during a Program or Bulk Erase cycle of the Flash memory. The Reset Flash instruction
aborts any on-going Sector Erase cycle, and returns the Flash memory to the normal READ
mode within a few milliseconds.
21.9
SRAM
The SRAM is enabled when SRAM Select (RS0) from the DPLD is High. SRAM Select
(RS0) can contain up to two product terms, allowing flexible memory mapping.
21.10
Sector Select and SRAM Select
Sector Select (FS0-FS3, CSBOOT0-CSBOOT1) and SRAM Select (RS0) are all outputs of
the DPLD. They are setup by writing equations for them in PSDsoft Express. The following
rules apply to the equations for these signals:
21.10.1
1.
Primary Flash memory and secondary Flash memory Sector Select signals must not
be larger than the physical sector size.
2.
Any primary Flash memory sector must not be mapped in the same memory space as
another Flash memory sector.
3.
A secondary Flash memory sector must not be mapped in the same memory space as
another secondary Flash memory sector.
4.
SRAM, I/O, and Peripheral I/O spaces must not overlap.
5.
A secondary Flash memory sector may overlap a primary Flash memory sector. In
case of overlap, priority is given to the secondary Flash memory sector.
6.
SRAM, I/O, and Peripheral I/O spaces may overlap any other memory sector. Priority is
given to the SRAM, I/O, or Peripheral I/O.
Example
FS0 is valid when the address is in the range of 8000h to BFFFh, CSBOOT0 is valid from
8000h to 9FFFh, and RS0 is valid from 8000h to 87FFh. Any address in the range of RS0
always accesses the SRAM. Any address in the range of CSBOOT0 greater than 87FFh
(and less than 9FFFh) automatically addresses secondary Flash memory segment 0. Any
address greater than 9FFFh accesses the primary Flash memory segment 0. You can see
that half of the primary Flash memory segment 0 and one-fourth of secondary Flash
memory segment 0 cannot be accessed in this example.
Note:
An equation that defined FS1 to anywhere in the range of 8000h to BFFFh would not be
valid.
Figure 49 shows the priority levels for all memory components. Any component on a higher
level can overlap and has priority over any component on a lower level. Components on the
same level must not overlap. Level one has the highest priority and level 3 has the lowest.
115/181
Memory blocks
21.10.2
UPSD3212A, UPSD3212C, UPSD3212CV
Memory Select configuration in Program and Data spaces
The MCU Core has separate address spaces for Program memory and Data memory. Any
of the memories within the PSD module can reside in either space or both spaces. This is
controlled through manipulation of the VM Register that resides in the CSIOP space.
The VM Register is set using PSDsoft Express to have an initial value. It can subsequently
be changed by the MCU so that memory mapping can be changed on-the-fly.
For example, you may wish to have SRAM and primary Flash memory in the Data space at
Boot-up, and secondary Flash memory in the Program space at Boot-up, and later swap the
primary and secondary Flash memories. This is easily done with the VM Register by using
PSDsoft Express Configuration to configure it for Boot-up and having the MCU change it
when desired. Table 86 describes the VM Register.
Figure 49. Priority level of memory and I/O components in the PSD module
Highest Priority
Level 1
SRAM, I/O, or
Peripheral I/O
Level 2
Secondary
Non-Volatile Memory
Level 3
Primary Flash Memory
Lowest Priority
Table 86.
Bit 7
PIO_EN
0=
disable
PIO
mode
1=
enable
PIO
mode
21.10.3
AI02867D
VM register
Bit 4
Bit 6
not
used
not
used
Bit 5
Primary
FL_Data
Bit 3
Secondary
Data
Bit 2
Primary
FL_Cod
e
Bit 1
Bit 0
Secondary
Code
SRAM_Co
de
not
used
0 = RD
can’t
access
Flash
memory
0 = RD can’t
access
Secondary
Flash memory
0=
PSEN
can’t
access
Flash
memory
0 = PSEN can’t
access
Secondary
Flash memory
0 = PSEN
can’t
access
SRAM
not
used
1 = RD
access
Flash
memory
1 = RD access
Secondary
Flash memory
1=
PSEN
access
Flash
memory
1 = PSEN
access
Secondary
Flash memory
1 = PSEN
access
SRAM
Separate Space mode
Program space is separated from Data space. For example, Program Select Enable (PSEN)
is used to access the program code from the primary Flash memory, while READ Strobe
(RD) is used to access data from the secondary Flash memory, SRAM and I/O Port blocks.
This configuration requires the VM Register to be set to 0Ch (see Figure 50).
116/181
UPSD3212A, UPSD3212C, UPSD3212CV
21.10.4
Memory blocks
Combined Space modes
The Program and Data spaces are combined into one memory space that allows the
primary Flash memory, secondary Flash memory, and SRAM to be accessed by either
Program Select Enable (PSEN) or READ Strobe (RD). For example, to configure the
primary Flash memory in Combined space, Bits b2 and b4 of the VM Register are set to '1'
(see Figure 51).
Figure 50. Separate Space mode
DPLD
Secondary
Flash
Memory
Primary
Flash
Memory
RS0
SRAM
CSBOOT0-1
FS0-FS3
CS
CS
OE
CS
OE
OE
PSEN
RD
AI07433
Figure 51. Combined Space mode
DPLD
RD
RS0
Primary
Flash
Memory
Secondary
Flash
Memory
SRAM
CSBOOT0-1
FS0-FS3
CS
CS
OE
CS
OE
OE
VM REG BIT 3
VM REG BIT 4
PSEN
VM REG BIT 1
VM REG BIT 2
RD
VM REG BIT 0
AI07434
21.11
Page register
The 8-bit Page Register increases the addressing capability of the MCU Core by a factor of
up to 256. The contents of the register can also be read by the MCU. The outputs of the
Page Register (PGR0-PGR7) are inputs to the DPLD decoder and can be included in the
Sector Select (FS0-FS7, CSBOOT0-CSBOOT3), and SRAM Select (RS0) equations.
If memory paging is not needed, or if not all 8 page register bits are needed for memory
paging, then these bits may be used in the CPLD for general logic.
117/181
Memory blocks
UPSD3212A, UPSD3212C, UPSD3212CV
Figure 52 shows the Page Register. The eight flip-flops in the register are connected to the
internal data bus D0-D7. The MCU can write to or read from the Page Register. The Page
Register can be accessed at address location CSIOP + E0h.
Figure 52. Page register
RESET
D0 - D 7
D0
Q0
D1
Q1
D2
Q2
D3
Q3
D4
Q4
D5
Q5
D6
Q6
D7
Q7
PGR0
INTERNAL PSD MODULE
SELECTS
AND LOGIC
PGR1
PGR2
PGR3
PGR4
DPLD
AND
CPLD
PGR5
PGR6
PGR7
R/W
PAGE
REGISTER
118/181
PLD
AI05799
UPSD3212A, UPSD3212C, UPSD3212CV
22
PLDs
PLDs
PLDs bring programmable logic functionality to the UPSD. After specifying the logic for the
PLDs using PSDsoft Express, the logic is programmed into the device and available upon
Power-up.
Table 87.
DPLD and CPLD Inputs
Input Source
Input Name
Number of
Signals
MCU Address Bus
A15-A0
16
MCU Control Signals
PSEN, RD, WR, ALE
4
RESET
RST
1
PDN
1
PA7-PA0
8
Port B Input Macrocells
PB7-PB0
8
Port C Input Macrocells
PC2-4, PC7
4
Port D Inputs
PD2-PD1
2
Page Register
PGR7-PGR0
8
Macrocell AB Feedback
MCELLAB.FB7-FB0
8
Macrocell BC Feedback
MCELLBC.FB7-FB0
8
Flash memory Program Status bit
Ready/Busy
1
Power-down
Port A Input
Macrocells(1)
Note: 1. These inputs are not available in the 52-pin package.
The PSD module contains two PLDs: the Decode PLD (DPLD), and the Complex PLD
(CPLD). The PLDs are briefly discussed in the next few paragraphs, and in more detail in
Section 22.2: Decode PLD (DPLD), and Section 22.3: Complex PLD (CPLD). Figure 53
shows the configuration of the PLDs.
The DPLD performs address decoding for Select signals for PSD module components, such
as memory, registers, and I/O ports.
The CPLD can be used for logic functions, such as loadable counters and shift registers,
state machines, and encoding and decoding logic. These logic functions can be constructed
using the Output Macrocells (OMC), Input Macrocells (IMC), and the AND Array. The CPLD
can also be used to generate External Chip Select (ECS1-ECS2) signals.
The AND Array is used to form product terms. These product terms are specified using
PSDsoft. The PLD input signals consist of internal MCU signals and external inputs from the
I/O ports. The input signals are shown in Table 87.
22.1
Turbo bit in PSD module
The PLDs can minimize power consumption by switching off when inputs remain unchanged
for an extended time of about 70ns. Resetting the Turbo bit to '0' (Bit 3 of PMMR0)
automatically places the PLDs into standby if no inputs are changing. Turning the Turbo
mode off increases propagation delays while reducing power consumption.
119/181
PLDs
UPSD3212A, UPSD3212C, UPSD3212CV
See Section 24: Power management for details on how to set the Turbo Bit.
Additionally, five bits are available in PMMR2 to block MCU control signals from entering the
PLDs. This reduces power consumption and can be used only when these MCU control
signals are not used in PLD logic equations.
Each of the two PLDs has unique characteristics suited for its applications. They are
described in the following sections.
Figure 53. PLD diagram
8
PAGE
REGISTER
DECODE PLD
73
8
PRIMARY FLASH MEMORY SELECTS
4
SECONDARY NON-VOLATILE MEMORY SELECTS
1
SRAM SELECT
1
CSIOP SELECT
PLD INPUT BUS
2
16
PERIPHERAL SELECTS
DIRECT MACROCELL ACCESS FROM MCU DATA BUS
OUTPUT MACROCELL FEEDBACK
CPLD
16 OUTPUT
MACROCELL
PT
ALLOC.
73
MACROCELL
ALLOC.
20 INPUT MACROCELL
(PORT A,B,C)
I/O PORTS
DATA
BUS
MCELLAB
TO PORT A OR B1
8
MCELLBC
TO PORT B OR C
8
2
EXTERNAL CHIP SELECTS
TO PORT D
DIRECT MACROCELL INPUT TO MCU DATA BUS
20
INPUT MACROCELL & INPUT PORTS
2
PORT D INPUTS
AI06600
1. Port A is not available in the 52-pin package
22.2
Decode PLD (DPLD)
The DPLD, shown in Figure 88, is used for decoding the address for PSD module and
external components. The DPLD can be used to generate the following decode signals:
120/181
●
4 Sector Select (FS0-FS3) signals for the primary Flash memory (three product terms
each)
●
2 Sector Select (CSBOOT0-CSBOOT1) signals for the secondary Flash memory (three
product terms each)
●
1 internal SRAM Select (RS0) signal (two product terms)
●
1 internal CSIOP Select signal (selects the PSD module registers)
●
2 internal Peripheral Select signals (Peripheral I/O mode).
UPSD3212A, UPSD3212C, UPSD3212CV
Table 88.
PLDs
DPLD logic array
(INPUTS)
I /O PORTS (PORT A,B,C)1
3
CSBOOT 0
3
CSBOOT 1
3
FS0
(20)
3
MCELLAB.FB [7:0] (FEEDBACKS)
FS1
(8)
3
MCELLBC.FB [7:0] (FEEDBACKS)
FS2
(8)
3
PGR0 -PGR7
(16)
PD[2:1]
(2)
PDN (APD OUTPUT)
(1)
PSEN, RD, WR, ALE2
(4)
RESET
2
RD_BSY
FS3
(8)
A[15:0]2
4 PRIMARY FLASH
MEMORY SECTOR
SELECTS
(1)
2
RS0
1
CSIOP
1
PSEL0
1
PSEL1
(1)
SRAM SELECT
I/O DECODER
SELECT
PERIPHERAL I/O
MODE SELECT
AI07436
1. Port A inputs are not available in the 52-pin package
2. Inputs from the MCU module
22.3
Complex PLD (CPLD)
The CPLD can be used to implement system logic functions, such as loadable counters and
shift registers, system mailboxes, handshaking protocols, state machines, and random logic.
The CPLD can also be used to generate External Chip Select (ECS1-ECS2), routed to Port
D.
Although External Chip Select (ECS1-ECS2) can be produced by any Output Macrocell
(OMC), these External Chip Select (ECS1-ECS2) on Port D do not consume any Output
Macrocells (OMC).
As shown in Figure 54, the CPLD has the following blocks:
●
20 Input Macrocells (IMC)
●
16 Output Macrocells (OMC)
●
Macrocell Allocator
●
Product Term Allocator
●
AND Array capable of generating up to 137 product terms
●
Four I/O Ports.
Each of the blocks are described in the sections that follow.
121/181
PLDs
UPSD3212A, UPSD3212C, UPSD3212CV
The Input Macrocells (IMC) and Output Macrocells (OMC) are connected to the PSD
module internal data bus and can be directly accessed by the MCU. This enables the MCU
software to load data into the Output Macrocells (OMC) or read data from both the Input and
Output Macrocells (IMC and OMC).
This feature allows efficient implementation of system logic and eliminates the need to
connect the data bus to the AND Array as required in most standard PLD macrocell
architectures.
Figure 54. Macrocell and I/O ports
PLD INPUT BUS
PRODUCT TERMS
FROM OTHER
MACROCELLS
MCU ADDRESS / DATA BUS
TO OTHER I/O PORTS
CPLD MACROCELLS
I/O PORTS
DATA
LOAD
CONTROL
PT PRESET
MCU DATA IN
PRODUCT TERM
ALLOCATOR
LATCHED
ADDRESS OUT
DATA
MCU LOAD
I/O PIN
D
Q
MUX
POLARITY
SELECT
MUX
AND ARRAY
WR
UP TO 10
PRODUCT TERMS
CPLD OUTPUT
PR DI LD
D/T
MUX
PT
CLOCK
PLD INPUT BUS
MACROCELL
OUT TO
MCU
GLOBAL
CLOCK
CK
CL
CLOCK
SELECT
SELECT
Q
D/T/JK FF
SELECT
COMB.
/REG
SELECT
CPLD
OUTPUT
PDR
MACROCELL
TO
I/O PORT
ALLOC.
INPUT
Q
DIR
REG.
D
WR
PT CLEAR
PT OUTPUT ENABLE (OE)
MACROCELL FEEDBACK
INPUT MACROCELLS
MUX
I/O PORT INPUT
ALE
MUX
PT INPUT LATCH GATE/CLOCK
Q D
Q D
G
AI06602
22.4
Output macrocell (OMC)
Eight of the Output Macrocells (OMC) are connected to Ports A and B pins and are named
as McellAB0-McellAB7. The other eight macrocells are connected to Ports B and C pins and
are named as McellBC0-McellBC7. If an McellAB output is not assigned to a specific pin in
PSDsoft, the Macrocell Allocator block assigns it to either Port A or B. The same is true for a
McellBC output on Port B or C. Table 89 shows the macrocells and port assignment.
The Output Macrocell (OMC) architecture is shown in Figure 55. As shown in the figure,
there are native product terms available from the AND Array, and borrowed product terms
available (if unused) from other Output Macrocells (OMC). The polarity of the product term
is controlled by the XOR gate. The Output Macrocell (OMC) can implement either sequential
logic, using the flip-flop element, or combinatorial logic. The multiplexer selects between the
sequential or combinatorial logic outputs. The multiplexer output can drive a port pin and
has a feedback path to the AND Array inputs.
The flip-flop in the Output Macrocell (OMC) block can be configured as a D, T, JK, or SR
type in PSDsoft. The flip-flop’s clock, preset, and clear inputs may be driven from a product
term of the AND Array. Alternatively, CLKIN (PD1) can be used for the clock input to the flip-
122/181
UPSD3212A, UPSD3212C, UPSD3212CV
PLDs
flop. The flip-flop is clocked on the rising edge of CLKIN (PD1). The preset and clear are
active High inputs. Each clear input can use up to two product terms.
Table 89.
Output
Macrocell
Output macrocell port and data bit assignments
Port
Assignment
(1,2)
Native Product
Terms
Max. Borrowed
Product Terms
Data Bit for
Loading or Reading
McellAB0
Port A0, B0
3
6
D0
McellAB1
Port A1, B1
3
6
D1
McellAB2
Port A2, B2
3
6
D2
McellAB3
Port A3, B3
3
6
D3
McellAB4
Port A4, B4
3
6
D4
McellAB5
Port A5, B5
3
6
D5
McellAB6
Port A6, B6
3
6
D6
McellAB7
Port A7, B7
3
6
D7
McellBC0
Port B0
4
5
D0
McellBC1
Port B1
4
5
D1
McellBC2
Port B2, C2
4
5
D2
McellBC3
Port B3, C3
4
5
D3
McellBC4
Port B4, C4
4
6
D4
McellBC5
Port B5
4
6
D5
McellBC6
Port B6
4
6
D6
McellBC7
Port B7, C7
4
6
D7
1. McellAB0-McellAB7 can only be assigned to Port B in the 52-pin package
2. Port PC0, PC1, PC5, and PC6 are assigned to JTAG pins and are not available as Macrocell outputs.
22.5
Product term allocator
The CPLD has a Product Term Allocator. PSDsoft uses the Product Term Allocator to
borrow and place product terms from one macrocell to another. The following list
summarizes how product terms are allocated:
●
McellAB0-McellAB7 all have three native product terms and may borrow up to six more
●
McellBC0-McellBC3 all have four native product terms and may borrow up to five more
●
McellBC4-McellBC7 all have four native product terms and may borrow up to six more.
Each macrocell may only borrow product terms from certain other macrocells. Product
terms already in use by one macrocell are not available for another macrocell.
If an equation requires more product terms than are available to it, then “external” product
terms are required, which consume other Output Macrocells (OMC). If external product
terms are used, extra delay is added for the equation that required the extra product terms.
This is called product term expansion. PSDsoft Express performs this expansion as needed.
123/181
PLDs
22.5.1
UPSD3212A, UPSD3212C, UPSD3212CV
Loading and Reading the Output Macrocells (OMC)
The Output Macrocells (OMC) block occupies a memory location in the MCU address
space, as defined by the CSIOP block (see Section 23: I/O ports (PSD module)). The flipflops in each of the 16 Output Macrocells (OMC) can be loaded from the data bus by a
MCU. Loading the Output Macrocells (OMC) with data from the MCU takes priority over
internal functions. As such, the preset, clear, and clock inputs to the flip-flop can be
overridden by the MCU. The ability to load the flip-flops and read them back is useful in such
applications as loadable counters and shift registers, mailboxes, and handshaking protocols.
Data can be loaded to the Output Macrocells (OMC) on the trailing edge of WRITE Strobe
(WR, edge loading) or during the time that WRITE Strobe (WR) is active (level loading). The
method of loading is specified in PSDsoft Express Configuration.
Figure 55. CPLD output macrocell
MASK
REG.
MACROCELL CS
MCU DATA BUS
D[ 7:0]
RD
PT
ALLOCATOR
WR
DIRECTION
REGISTER
ENABLE (.OE)
AND ARRAY
PLD INPUT BUS
PRESET(.PR)
COMB/REG
SELECT
PT
PT
DIN PR
MUX
PT
LD
POLARITY
SELECT
Q
I/O PIN
MACROCELL
ALLOCATOR
IN
CLEAR (.RE)
CLR
PORT
DRIVER
PROGRAMMABLE
FF (D/T/JK /SR)
PT CLK
MUX
CLKIN
FEEDBACK (.FB)
PORT INPUT
INPUT
MACROCELL
AI06617
22.5.2
OMC mask register
There is one Mask Register for each of the two groups of eight Output Macrocells (OMC).
The Mask Registers can be used to block the loading of data to individual Output Macrocells
(OMC). The default value for the Mask Registers is 00h, which allows loading of the Output
Macrocells (OMC). When a given bit in a Mask Register is set to a '1,' the MCU is blocked
from writing to the associated Output Macrocells (OMC). For example, suppose McellAB0McellAB3 are being used for a state machine. You would not want a MCU write to McellAB
to overwrite the state machine registers. Therefore, you would want to load the Mask
Register for McellAB (Mask Macrocell AB) with the value 0Fh.
22.5.3
Output enable of the OMC
The Output Macrocells (OMC) block can be connected to an I/O port pin as a PLD output.
The output enable of each port pin driver is controlled by a single product term from the
124/181
UPSD3212A, UPSD3212C, UPSD3212CV
PLDs
AND Array, ORed with the Direction Register output. The pin is enabled upon Power-up if no
output enable equation is defined and if the pin is declared as a PLD output in PSDsoft
Express.
If the Output Macrocell (OMC) output is declared as an internal node and not as a port pin
output in the PSDabel file, the port pin can be used for other I/O functions. The internal node
feedback can be routed as an input to the AND Array.
Input macrocells (IMC)
The CPLD has 20 Input Macrocells (IMC), one for each pin on Ports A and B, and 4 on Port
C. The architecture of the Input Macrocells (IMC) is shown in Figure 56. The Input
Macrocells (IMC) are individually configurable, and can be used as a latch, register, or to
pass incoming Port signals prior to driving them onto the PLD input bus. The outputs of the
Input Macrocells (IMC) can be read by the MCU through the internal data bus.
The enable for the latch and clock for the register are driven by a multiplexer whose inputs
are a product term from the CPLD AND Array or the MCU Address Strobe (ALE). Each
product term output is used to latch or clock four Input Macrocells (IMC). Port inputs 3-0 can
be controlled by one product term and 7-4 by another.
Configurations for the Input Macrocells (IMC) are specified by equations written in PSDsoft
(see Application Note AN1171). Outputs of the Input Macrocells (IMC) can be read by the
MCU via the IMC buffer.
See Section 23: I/O ports (PSD module).
Figure 56. Input macrocell
MCU DATA BUS
D[7:0]
INPUT MACROCELL _ RD
DIRECTION
REGISTER
ENABLE (.OE)
AND ARRAY
PT
PLD INPUT BUS
22.6
OUTPUT
MACROCELLS BC
AND
MACROCELL AB
I/O PIN
PT
PORT
DRIVER
MUX
Q
D
PT
MUX
ALE
D FF
FEEDBACK
Q
D
G
LATCH
INPUT MACROCELL
AI06603
125/181
I/O ports (PSD module)
23
UPSD3212A, UPSD3212C, UPSD3212CV
I/O ports (PSD module)
There are four programmable I/O ports: Ports A, B, C, and D in the PSD module. Each of the
ports is eight bits except Port D, which is 3 bits. Each port pin is individually user
configurable, thus allowing multiple functions per port. The ports are configured using
PSDsoft Express Configuration or by the MCU writing to on-chip registers in the CSIOP
space. Port A is not available in the 52-pin package.
The topics discussed in this section are:
23.1
●
General Port architecture
●
Port operating modes
●
Port Configuration Registers (PCR)
●
Port Data Registers
●
Individual Port functionality.
General port architecture
The general architecture of the I/O Port block is shown in Figure 57. Individual Port
architectures are shown in Figure 59 to Figure 62. In general, once the purpose for a port
pin has been defined, that pin is no longer available for other purposes. Exceptions are
noted.
As shown in Figure 57, the ports contain an output multiplexer whose select signals are
driven by the configuration bits in the Control Registers (Ports A and B only) and PSDsoft
Express Configuration. Inputs to the multiplexer include the following:
●
Output data from the Data Out register
●
Latched address outputs
●
CPLD macrocell output
●
External Chip Select (ECS1-ECS2) from the CPLD.
The Port Data Buffer (PDB) is a tri-state buffer that allows only one source at a time to be
read. The Port Data Buffer (PDB) is connected to the Internal Data Bus for feedback and
can be read by the MCU. The Data Out and macrocell outputs, Direction and Control
Registers, and port pin input are all connected to the Port Data Buffer (PDB).
126/181
UPSD3212A, UPSD3212C, UPSD3212CV
I/O ports (PSD module)
Figure 57. General I/O port architecture
DATA OUT
REG.
D
Q
D
Q
DATA OUT
WR
ADDRESS
ALE
ADDRESS
PORT PIN
OUTPUT
MUX
G
MACROCELL OUTPUTS
EXT CS
READ MUX
MCU DATA BUS
P
OUTPUT
SELECT
D
DATA IN
B
CONTROL REG.
D
Q
ENABLE OUT
WR
DIR REG.
D
Q
WR
ENABLE PRODUCT TERM (.OE)
INPUT
MACROCELL
CPLD-INPUT
AI06604
The Port pin’s tri-state output driver enable is controlled by a two input OR gate whose
inputs come from the CPLD AND Array enable product term and the Direction Register. If
the enable product term of any of the Array outputs are not defined and that port pin is not
defined as a CPLD output in the PSDsoft, then the Direction Register has sole control of the
buffer that drives the port pin.
The contents of these registers can be altered by the MCU. The Port Data Buffer (PDB)
feedback path allows the MCU to check the contents of the registers.
Ports A, B, and C have embedded Input Macrocells (IMC). The Input Macrocells (IMC) can
be configured as latches, registers, or direct inputs to the PLDs. The latches and registers
are clocked by Address Strobe (ALE) or a product term from the PLD AND Array. The
outputs from the Input Macrocells (IMC) drive the PLD input bus and can be read by the
MCU. See Figure 56.
23.2
Port operating modes
The I/O Ports have several modes of operation. Some modes can be defined using PSDsoft,
some by the MCU writing to the Control Registers in CSIOP space, and some by both. The
modes that can only be defined using PSDsoft must be programmed into the device and
cannot be changed unless the device is reprogrammed. The modes that can be changed by
the MCU can be done so dynamically at run-time. The PLD I/O, Data Port, Address Input,
and Peripheral I/O modes are the only modes that must be defined before programming the
device. All other modes can be changed by the MCU at run-time. See Application Note
AN1171 for more detail.
Table 90 summarizes which modes are available on each port. Table 93 shows how and
where the different modes are configured. Each of the port operating modes are described
in the following sections.
127/181
I/O ports (PSD module)
23.3
UPSD3212A, UPSD3212C, UPSD3212CV
MCU I/O mode
In the MCU I/O mode, the MCU uses the I/O Ports block to expand its own I/O ports. By
setting up the CSIOP space, the ports on the PSD module are mapped into the MCU
address space. The addresses of the ports are listed in Table 81.
A port pin can be put into MCU I/O mode by writing a '0' to the corresponding bit in the
Control Register. The MCU I/O direction may be changed by writing to the corresponding bit
in the Direction Register, or by the output enable product term. See Section 23.6: Peripheral
I/O mode. When the pin is configured as an output, the content of the Data Out Register
drives the pin. When configured as an input, the MCU can read the port input through the
Data In buffer. See Figure 57.
Ports C and D do not have Control Registers, and are in MCU I/O mode by default. They can
be used for PLD I/O if equations are written for them in PSDabel.
23.4
PLD I/O mode
The PLD I/O mode uses a port as an input to the CPLD’s Input Macrocells (IMC), and/or as
an output from the CPLD’s Output Macrocells (OMC). The output can be tri-stated with a
control signal. This output enable control signal can be defined by a product term from the
PLD, or by resetting the corresponding bit in the Direction Register to '0.' The corresponding
bit in the Direction Register must not be set to '1' if the pin is defined for a PLD input signal in
PSDsoft. The PLD I/O mode is specified in PSDsoft by declaring the port pins, and then
writing an equation assigning the PLD I/O to a port.
23.5
Address Out mode
Address Out mode can be used to drive latched MCU addresses on to the port pins. These
port pins can, in turn, drive external devices. Either the output enable or the corresponding
bits of both the Direction Register and Control Register must be set to a '1' for pins to use
Address Out mode. This must be done by the MCU at run-time. See Table 92 for the
address output pin assignments on Ports A and B for various MCUs.
23.6
Peripheral I/O mode
Peripheral I/O mode can be used to interface with external peripherals. In this mode, all of
Port A serves as a tri-state, bi-directional data buffer for the MCU. Peripheral I/O mode is
enabled by setting Bit 7 of the VM Register to a '1.' Figure 58 shows how Port A acts as a bidirectional buffer for the MCU data bus if Peripheral I/O mode is enabled. An equation for
PSEL0 and/or PSEL1 must be written in PSDsoft. The buffer is tri-stated when PSEL0 or
PSEL1 is low (not active). The PSEN signal should be “ANDed” in the PSEL equations to
disable the buffer when PSEL resides in the data space.
23.7
JTAG in-system programming (ISP)
Port C is JTAG compliant, and can be used for In-System Programming (ISP). For more
information on the JTAG Port, see Section 26: Programming in-circuit using the JTAG serial
interface.
128/181
UPSD3212A, UPSD3212C, UPSD3212CV
I/O ports (PSD module)
Figure 58. Peripheral I/O mode
RD
PSEL0
PSEL
PSEL1
D0 - D7
VM REGISTER BIT 7
PA0 - PA7
DATA BUS
WR
AI02886
Table 90.
Port operating modes
Port A(1)
Port B
Port C
Port D
Yes
Yes
Yes
Yes
Yes
No
No
Yes
Yes
No
No
Yes(2)
No
No
No
Yes
Yes
Yes
Yes
Yes
Address Out
Yes (A7 – 0)
Yes (A7 – 0)
No
No
Peripheral I/O
Yes
No
No
No
Port mode
MCU I/O
PLD I/O
McellAB Outputs
McellBC Outputs
Additional Ext. CS
Outputs
PLD Inputs
JTAG ISP
No
(3)
No
No
Yes
1. Port A is not available in the 52-pin package.
2. On pins PC2, PC3, PC4, and PC7 only.
3. JTAG pins (TMS, TCK, TDI, TDO) are dedicated pins.
Table 91.
Port operating mode settings
Mode
Control
Register
Setting(1)
Defined in PSDsoft
Direction
Register
Setting(1)
VM Register
Setting(1)
MCU I/O
Declare pins only
0
1 = output,
0 = input (Note 2)
N/A
PLD I/O
Logic equations
N/A
(Note 2)
N/A
Address Out
(Port A,B)
Declare pins only
1
1 (Note 2)
N/A
Peripheral I/O
(Port A)
Logic equations
(PSEL0 & 1)
N/A
N/A
PIO Bit = 1
1. N/A = Not Applicable
2. The direction of the Port A,B,C, and D pins are controlled by the Direction Register ORed with the
individual output enable product term (.oe) from the CPLD AND Array.
Table 92.
I/O port latched address output assignments
Port A (PA3-PA0)
Port A (PA7-PA4)
Port B (PB3-PB0)
Port B (PB7-PB4)
Address a3-a0
Address a7-a4
Address a3-a0
Address a7-a4
129/181
I/O ports (PSD module)
23.8
UPSD3212A, UPSD3212C, UPSD3212CV
Port configuration registers (PCR)
Each Port has a set of Port Configuration Registers (PCR) used for configuration. The
contents of the registers can be accessed by the MCU through normal READ/WRITE bus
cycles at the addresses given in Table 81. The addresses in Table 81 are the offsets in
hexadecimal from the base of the CSIOP register.
The pins of a port are individually configurable and each bit in the register controls its
respective pin. For example, Bit 0 in a register refers to Bit 0 of its port. The three Port
Configuration Registers (PCR), shown in Table 93, are used for setting the Port
configurations. The default Power-up state for each register in Table 93 is 00h.
23.8.1
Control register
Any bit reset to '0' in the Control Register sets the corresponding port pin to MCU I/O mode,
and a '1' sets it to Address Out mode. The default mode is MCU I/O. Only Ports A and B
have an associated Control Register.
23.8.2
Direction register
The Direction Register, in conjunction with the output enable (except for Port D), controls the
direction of data flow in the I/O Ports. Any bit set to '1' in the Direction Register causes the
corresponding pin to be an output, and any bit set to '0' causes it to be an input. The default
mode for all port pins is input.
Figure 59 and Figure 60 show the Port Architecture diagrams for Ports A/B and C,
respectively. The direction of data flow for Ports A, B, and C are controlled not only by the
direction register, but also by the output enable product term from the PLD AND Array. If the
output enable product term is not active, the Direction Register has sole control of a given
pin’s direction.
An example of a configuration for a Port with the three least significant bits set to output and
the remainder set to input is shown in Table 96. Since Port D only contains two pins (shown
in Figure 62), the Direction Register for Port D has only two bits active.
23.8.3
Drive Select register
The Drive Select Register configures the pin driver as Open Drain or CMOS for some port
pins, and controls the slew rate for the other port pins. An external pull-up resistor should be
used for pins configured as Open Drain.
A pin can be configured as Open Drain if its corresponding bit in the Drive Select Register is
set to a '1.' The default pin drive is CMOS.
Note:
The slew rate is a measurement of the rise and fall times of an output. A higher slew rate
means a faster output response and may create more electrical noise. A pin operates in a
high slew rate when the corresponding bit in the Drive Register is set to '1.' The default rate
is slow slew.
Table 97 shows the Drive Register for Ports A, B, C, and D. It summarizes which pins can be
configured as Open Drain outputs and which pins the slew rate can be set for.
130/181
UPSD3212A, UPSD3212C, UPSD3212CV
Table 93.
I/O ports (PSD module)
Port configuration registers (PCR)
Register Name
Port
Control
Direction
Drive Select
(1)
MCU Access
A,B
WRITE/READ
A,B,C,D
WRITE/READ
A,B,C,D
WRITE/READ
Note: 1. See Table 97 for Drive Register Bit definition.
Table 94.
Table 95.
Direction Register Bit
Port Pin mode
0
Input
1
Output
Port pin direction control, output enable P.T. defined
Direction Register Bit
Output Enable P.T.
Port Pin mode
0
0
Input
0
1
Output
1
0
Output
1
1
Output
Table 96.
23.9
Port pin direction control, output enable P.T. not defined
Port direction assignment example
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
0
0
1
1
1
Port data registers
The Port Data Registers, shown in Table 98, are used by the MCU to write data to or read
data from the ports. Table 98 shows the register name, the ports having each register type,
and MCU access for each register type. The registers are described below.
23.9.1
Data In
Port pins are connected directly to the Data In buffer. In MCU I/O Input mode, the pin input is
read through the Data In buffer.
23.9.2
Data Out register
Stores output data written by the MCU in the MCU I/O Output mode. The contents of the
Register are driven out to the pins if the Direction Register or the output enable product term
is set to '1.' The contents of the register can also be read back by the MCU.
23.9.3
Output macrocells (OMC)
The CPLD Output Macrocells (OMC) occupy a location in the MCU’s address space. The
MCU can read the output of the Output Macrocells (OMC). If the OMC Mask Register Bits
131/181
I/O ports (PSD module)
UPSD3212A, UPSD3212C, UPSD3212CV
are not set, writing to the macrocell loads data to the macrocell flip-flops. See Section 22:
PLDs.
23.9.4
OMC mask register
Each OMC Mask Register Bit corresponds to an Output Macrocell (OMC) flip-flop. When the
OMC Mask Register Bit is set to a '1,' loading data into the Output Macrocell (OMC) flip-flop
is blocked. The default value is '0' or unblocked.
23.9.5
Input macrocells (IMC)
The Input Macrocells (IMC) can be used to latch or store external inputs. The outputs of the
Input Macrocells (IMC) are routed to the PLD input bus, and can be read by the MCU. See
Section 22: PLDs.
23.9.6
Enable out
The Enable Out register can be read by the MCU. It contains the output enable values for a
given port. A '1' indicates the driver is in output mode. A '0' indicates the driver is in tri-state
and the pin is in input mode.
Table 97.
Drive register pin assignment
Drive
Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Port A
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Port B
Open
Drain
Open
Drain
Open
Drain
Open
Drain
Slew
Rate
Slew
Rate
Slew
Rate
Slew
Rate
Port C
Open
Drain
NA(1)
NA(1)
Open
Drain
Open
Drain
Open
Drain
NA(1)
NA(1)
Port D
NA(1)
NA(1)
NA(1)
NA(1)
NA(1)
Slew
Rate
Slew
Rate
NA(1)
1. NA = Not Applicable.
Table 98.
Port data registers
Register Name
132/181
Port
MCU Access
Data In
A,B,C,D
READ – input on pin
Data Out
A,B,C,D
WRITE/READ
Output Macrocell
A,B,C
READ – outputs of macrocells
WRITE – loading macrocells flip-flop
Mask Macrocell
A,B,C
WRITE/READ – prevents loading into a given
macrocell
Input Macrocell
A,B,C
READ – outputs of the Input Macrocells
Enable Out
A,B,C
READ – the output enable control of the port driver
UPSD3212A, UPSD3212C, UPSD3212CV
23.10
I/O ports (PSD module)
Ports A and B – functionality and structure
Ports A and B have similar functionality and structure, as shown in Figure 59. The two ports
can be configured to perform one or more of the following functions:
●
MCU I/O mode
●
CPLD Output – Macrocells McellAB7-McellAB0 can be connected to Port A or Port B.
McellBC7-McellBC0 can be connected to Port B or Port C.
●
CPLD Input – Via the Input Macrocells (IMC).
●
Latched Address output – Provide latched address output as per Table 92.
●
Open Drain/Slew Rate – pins PA3-PA0 and PB3-PB0 can be configured to fast slew
rate, pins PA7-PA4 and PB7-PB4 can be configured to Open Drain mode.
●
Peripheral mode – Port A only (80-pin package)
Figure 59. Port A and Port B structure
DATA OUT
REG.
D
Q
D
Q
DATA OUT
WR
ADDRESS
ALE
PORT
A OR B PIN
ADDRESS
A[ 7:0]
G
OUTPUT
MUX
MACROCELL OUTPUTS
READ MUX
MCU DATA BUS
P
OUTPUT
SELECT
D
DATA IN
B
CONTROL REG.
D
Q
ENABLE OUT
WR
DIR REG.
D
Q
WR
ENABLE PRODUCT TERM (.OE)
INPUT
MACROCELL
CPLD- INPUT
AI06605
23.11
Port C – functionality and structure
Port C can be configured to perform one or more of the following functions (see Figure 60):
●
MCU I/O mode
●
CPLD Output – McellBC7-McellBC0 outputs can be connected to Port B or Port C.
●
CPLD Input – via the Input Macrocells (IMC)
●
In-System Programming (ISP) – JTAG pins (TMS, TCK, TDI, TDO) are dedicated pins
for device programming. (See Section 26: Programming in-circuit using the JTAG serial
interface, for more information on JTAG programming.)
●
Open Drain – Port C pins can be configured in Open Drain mode
Port C does not support Address Out mode, and therefore no Control Register is required.
133/181
I/O ports (PSD module)
UPSD3212A, UPSD3212C, UPSD3212CV
Figure 60. Port C structure
DATA OUT
REG.
D
DATA OUT
Q
WR
SPECIAL FUNCTION
PORT C PIN
1
OUTPUT
MUX
MCELLBC[ 7:0]
MCU DATA BUS
READ MUX
P
OUTPUT
SELECT
D
DATA IN
B
ENABLE OUT
DIR REG.
D
Q
WR
ENABLE PRODUCT TERM (.OE)
INPUT
MACROCELL
CPLD - INPUT
SPECIAL FUNCTION
1
CONFIGURATION
BIT
AI06618
Note: 1. ISP
23.12
Port D – functionality and structure
Port D has two I/O pins (only one pin, PD1, in the 52-pin package). See Figure 61 and
Figure 62. This port does not support Address Out mode, and therefore no Control Register
is required. Of the eight bits in the Port D registers, only Bits 2 and 1 are used to configure
pins PD2 and PD1.
Port D can be configured to perform one or more of the following functions:
●
MCU I/O mode
●
CPLD Output – External Chip Select (ECS1-ECS2)
●
CPLD Input – direct input to the CPLD, no Input Macrocells (IMC)
●
Slew rate – pins can be set up for fast slew rate
Port D pins can be configured in PSDsoft Express as input pins for other dedicated
functions:
134/181
●
CLKIN (PD1) as input to the macrocells flip-flops and APD counter
●
PSD Chip Select Input (CSI, PD2). Driving this signal High disables the Flash memory,
SRAM and CSIOP.
UPSD3212A, UPSD3212C, UPSD3212CV
I/O ports (PSD module)
Figure 61. Port D structure
DATA OUT
REG.
DATA OUT
D
Q
WR
PORT D PIN
OUTPUT
MUX
ECS[ 2:1]
MCU DATA BUS
READ MUX
OUTPUT
SELECT
P
D
DATA IN
B
ENABLE PRODUCT
TERM (.OE)
DIR REG.
D
WR
23.13
Q
CPLD-INPUT
AI06606
External chip select
The CPLD also provides two External Chip Select (ECS1-ECS2) outputs on Port D pins that
can be used to select external devices. Each External Chip Select (ECS1-ECS2) consists of
one product term that can be configured active High or Low. The output enable of the pin is
controlled by either the output enable product term or the Direction register. (See Figure 62.)
135/181
I/O ports (PSD module)
UPSD3212A, UPSD3212C, UPSD3212CV
Figure 62. Port D external chip select signals
ENABLE (.OE)
ENABLE (.OE)
PT2
DIRECTION
REGISTER
ECS2
POLARITY
BIT
136/181
PD1 PIN
ECS1
POLARITY
BIT
CPLD AND ARRAY
PLD INPUT BUS
PT1
DIRECTION
REGISTER
PD2 PIN
AI06607
UPSD3212A, UPSD3212C, UPSD3212CV
24
Power management
Power management
All PSD modules offer configurable power saving options. These options may be used
individually or in combinations, as follows:
●
The primary and secondary Flash memory, and SRAM blocks are built with power
management technology. In addition to using special silicon design methodology,
power management technology puts the memories into Standby mode when
address/data inputs are not changing (zero DC current). As soon as a transition occurs
on an input, the affected memory “wakes up,” changes and latches its outputs, then
goes back to standby. The designer does not have to do anything special to achieve
Memory Standby mode when no inputs are changing—it happens automatically.
●
The PLD sections can also achieve Standby mode when its inputs are not changing, as
described in the sections on the Power Management mode Registers (PMMR).
●
As with the Power Management mode, the Automatic Power Down (APD) block allows
the PSD module to reduce to Standby current automatically. The APD Unit can also
block MCU address/data signals from reaching the memories and PLDs.
●
Built in logic monitors the Address Strobe of the MCU for activity. If there is no activity
for a certain time period (MCU is asleep), the APD Unit initiates Power-down mode (if
enabled). Once in Power-down mode, all address/data signals are blocked from
reaching memory and PLDs, and the memories are deselected internally. This allows
the memory and PLDs to remain in Standby mode even if the address/data signals are
changing state externally (noise, other devices on the MCU bus, etc.). Keep in mind
that any unblocked PLD input signals that are changing states keeps the PLD out of
Standby mode, but not the memories.
●
PSD Chip Select Input (CSI, PD2) can be used to disable the internal memories,
placing them in Standby mode even if inputs are changing. This feature does not block
any internal signals or disable the PLDs. This is a good alternative to using the APD
Unit. There is a slight penalty in memory access time when PSD Chip Select Input
(CSI, PD2) makes its initial transition from deselected to selected.
●
The PMMRs can be written by the MCU at run-time to manage power. The PSD
module supports “blocking bits” in these registers that are set to block designated
signals from reaching both PLDs. Current consumption of the PLDs is directly related
to the composite frequency of the changes on their inputs (see Figure Figure 66 and
Figure 67). Significant power savings can be achieved by blocking signals that are not
used in DPLD or CPLD logic equations.
137/181
Power management
UPSD3212A, UPSD3212C, UPSD3212CV
Figure 63. APD unit
APD EN
PMMR0 BIT 1=1
TRANSITION
DETECTION
DISABLE BUS
INTERFACE
ALE
CLR
PD
CSIOP SELECT
APD
COUNTER
RESET
FLASH SELECT
EDGE
DETECT
CSI
CLKIN
PD
PLD
SRAM SELECT
POWER DOWN
(PDN) SELECT
DISABLE
FLASH/SRAM
AI06608
The PSD module has a Turbo Bit in PMMR0. This bit can be set to turn the Turbo mode off
(the default is with Turbo mode turned on). While Turbo mode is off, the PLDs can achieve
standby current when no PLD inputs are changing (zero DC current). Even when inputs do
change, significant power can be saved at lower frequencies (AC current), compared to
when Turbo mode is on. When the Turbo mode is on, there is a significant DC current
component and the AC component is higher.
Automatic Power-down (APD) Unit and Power-down mode
The APD Unit, shown in Figure 63, puts the PSD module into Power-down mode by
monitoring the activity of Address Strobe (ALE). If the APD Unit is enabled, as soon as
activity on Address Strobe (ALE) stops, a four-bit counter starts counting. If Address Strobe
(ALE/AS, PD0) remains inactive for fifteen clock periods of CLKIN (PD1), Power-down
(PDN) goes High, and the PSD module enters Power-down mode, as discussed next.
Power-down mode
By default, if you enable the APD Unit, Power-down mode is automatically enabled. The
device enters Power-down mode if Address Strobe (ALE) remains inactive for fifteen periods
of CLKIN (PD1).
The following should be kept in mind when the PSD module is in Power-down mode:
Note:
138/181
●
If Address Strobe (ALE) starts pulsing again, the PSD module returns to normal
Operating mode. The PSD module also returns to normal Operating mode if either PSD
Chip Select Input (CSI, PD2) is Low or the RESET input is High.
●
The MCU address/data bus is blocked from all memory and PLDs.
●
Various signals can be blocked (prior to Power-down mode) from entering the PLDs by
setting the appropriate bits in the PMMR registers. The blocked signals include MCU
control signals and the common CLKIN (PD1).
Blocking CLKIN (PD1) from the PLDs does not block CLKIN (PD1) from the APD Unit.
●
All memories enter Standby mode and are drawing standby current. However, the PLD
and I/O ports blocks do not go into Standby mode because you don’t want to have to
wait for the logic and I/O to “wake-up” before their outputs can change. See Table 99 for
Power-down mode effects on PSD module ports.
●
Typical standby current is of the order of microamperes. These standby current values
assume that there are no transitions on any PLD input.
UPSD3212A, UPSD3212C, UPSD3212CV
Power management
Other power-saving options
The PSD module offers other reduced power saving options that are independent of the
Power-down mode. Except for the PSD Chip Select Input (CSI, PD2) features, they are
enabled by setting bits in PMMR0 and PMMR2.
Figure 64. Enable Power-down flowchart
RESET
Enable APD
Set PMMR0 Bit 1 = 1
OPTIONAL
Disable desired inputs to PLD
by setting PMMR0 bits 4 and 5
and PMMR2 bits 2 through 6.
No
ALE idle
for 15 CLKIN
clocks?
Yes
PSD Module in Power
Down Mode
Table 99.
Power-down mode’s effect on ports
Port Function
24.1
AI06609
Pin Level
MCU I/O
No Change
PLD Out
No Change
Address Out
Undefined
Peripheral I/O
Tri-State
PLD power management
The power and speed of the PLDs are controlled by the Turbo Bit (Bit 3) in PMMR0. By
setting the bit to '1,' the Turbo mode is off and the PLDs consume the specified Standby
current when the inputs are not switching for an extended time of 70 ns. The propagation
delay time is increased by 10 ns (for a 5 V device) after the Turbo Bit is set to '1' (turned off)
when the inputs change at a composite frequency of less than 15MHz. When the Turbo Bit
is reset to '0' (turned on), the PLDs run at full power and speed. The Turbo Bit affects the
PLD’s DC power, AC power, and propagation delay. When the Turbo mode is off, the
UPSD321xx devices’ input clock frequency is reduced by 5 MHz from the maximum rated
clock frequency.
Blocking MCU control signals with the bits of PMMR2 can further reduce PLD AC power
consumption.
139/181
Power management
24.2
UPSD3212A, UPSD3212C, UPSD3212CV
PSD chip select input (CSI, PD2)
PD2 of Port D can be configured in PSDsoft Express as PSD Chip Select Input (CSI). When
Low, the signal selects and enables the PSD module Flash memory, SRAM, and I/O blocks
for READ or WRITE operations. A High on PSD Chip Select Input (CSI, PD2) disables the
Flash memory, and SRAM, and reduces power consumption. However, the PLD and I/O
signals remain operational when PSD Chip Select Input (CSI, PD2) is High.
24.3
Input clock
CLKIN (PD1) can be turned off, to the PLD to save AC power consumption. CLKIN (PD1) is
an input to the PLD AND Array and the Output Macrocells (OMC).
During Power-down mode, or, if CLKIN (PD1) is not being used as part of the PLD logic
equation, the clock should be disabled to save AC power. CLKIN (PD1) is disconnected from
the PLD AND Array or the Macrocells block by setting Bits 4 or 5 to a '1' in PMMR0.
24.4
Input control signals
The PSD module provides the option to turn off the MCU signals (WR, RD, PSEN, and
Address Strobe (ALE)) to the PLD to save AC power consumption. These control signals
are inputs to the PLD AND Array. During Power-down mode, or, if any of them are not being
used as part of the PLD logic equation, these control signals should be disabled to save AC
power. They are disconnected from the PLD AND Array by setting Bits 2, 3, 4, 5, and 6 to a
'1' in PMMR2.
Table 100. Power management mode registers (PMMR0)
Bit 0
X
Bit 1
APD Enable
Bit 2
Bit 3
Bit 4
Not used, and should be set to zero.
0 = off
Automatic Power-down (APD) is disabled.
1 = on
Automatic Power-down (APD) is enabled.
0
Not used, and should be set to zero.
0 = on
PLD Turbo mode is on
1 = off
PLD Turbo mode is off, saving power.
UPSD321xx devices operate at 5MHz below the maximum rated
clock frequency
0 = on
CLKIN (PD1) input to the PLD AND Array is connected. Every
change of CLKIN (PD1) Powers-up the PLD when Turbo Bit is '0.'
1 = off
CLKIN (PD1) input to PLD AND Array is disconnected, saving
power.
PLD Turbo
PLD Array
clk
0 = on
CLKIN (PD1) input to the PLD macrocells is connected.
PLD MCell
clk
1 = off
CLKIN (PD1) input to PLD macrocells is disconnected, saving
power.
Bit 6
X
0
Not used, and should be set to zero.
Bit 7
X
0
Not used, and should be set to zero.
Bit 5
140/181
X
0
UPSD3212A, UPSD3212C, UPSD3212CV
Power management
Table 101. Power management mode registers (PMMR2)
Bit 0
X
0
Not used, and should be set to zero.
Bit 1
X
0
Not used, and should be set to zero.
PLD Array
WR
0 = on
WR input to the PLD AND Array is connected.
Bit 2
1 = off
WR input to PLD AND Array is disconnected, saving power.
PLD Array
RD
0 = on
RD input to the PLD AND Array is connected.
1 = off
RD input to PLD AND Array is disconnected, saving power.
PLD Array
PSEN
0 = on
PSEN input to the PLD AND Array is connected.
1 = off
PSEN input to PLD AND Array is disconnected, saving power.
PLD Array
ALE
0 = on
ALE input to the PLD AND Array is connected.
1 = off
ALE input to PLD AND Array is disconnected, saving power.
Bit 6
X
0
Not used, and should be set to zero.
Bit 7
X
0
Not used, and should be set to zero.
Bit 3
Bit 4
Bit 5
1. The bits of this register are cleared to zero following Power-up. Subsequent RESET pulses do not clear the
registers.
Table 102. APD counter operatio
APD Enable Bit
ALE Level
APD Counter
0
X
Not Counting
1
Pulsing
Not Counting
1
0 or 1
Counting (Generates PDN after 15
Clocks)
141/181
RESET timing and device status at reset
25
UPSD3212A, UPSD3212C, UPSD3212CV
RESET timing and device status at reset
Upon Power-up, the PSD module requires a Reset (RESET) pulse of duration tNLNH-PO after
VCC is steady. During this period, the device loads internal configurations, clears some of
the registers and sets the Flash memory into operating mode. After the rising edge of Reset
(RESET), the PSD module remains in the Reset mode for an additional period, tOPR, before
the first memory access is allowed.
The Flash memory is reset to the READ mode upon Power-up. Sector Select (FS0-FS3 and
CSBOOT0-CSBOOT1) must all be Low, WRITE Strobe (WR, CNTL0) High, during Poweron RESET for maximum security of the data contents and to remove the possibility of a byte
being written on the first edge of WRITE Strobe (WR). Any Flash memory WRITE cycle
initiation is prevented automatically when VCC is below VLKO.
25.1
Warm RESET
Once the device is up and running, the PSD module can be reset with a pulse of a much
shorter duration, tNLNH. The same tOPR period is needed before the device is operational
after a Warm RESET. Figure 65 shows the timing of the Power-up and Warm RESET.
25.2
I/O pin, register and PLD status at RESET
Table 103 shows the I/O pin, register and PLD status during Power-on RESET, Warm
RESET, and Power-down mode. PLD outputs are always valid during Warm RESET, and
they are valid in Power-on RESET once the internal Configuration bits are loaded. This
loading is completed typically long before the VCC ramps up to operating level. Once the
PLD is active, the state of the outputs are determined by the PLD equations.
Figure 65. Reset (RESET) timing
VCC
VCC(min)
tNLNH-PO
Power-On Reset
tOPR
tNLNH
tNLNH-A
tOPR
Warm Reset
RESET
AI02866b
142/181
UPSD3212A, UPSD3212C, UPSD3212CV
RESET timing and device status at reset
Table 103. Status during Power-on RESET, Warm RESET and Power-down mode
Port Configuration
Power-On RESET
Warm RESET
MCU I/O
Input mode
PLD Output
Valid after internal PSD
configuration bits are
Valid
loaded
Depends on inputs to
PLD (addresses are
blocked in PD mode)
Address Out
Tri-stated
Tri-stated
Not defined
Peripheral I/O
Tri-stated
Tri-stated
Tri-stated
Register
Power-On RESET
Input mode
Power-down mode
Warm RESET
Unchanged
Power-down mode
PMMR0 and PMMR2
Cleared to '0'
Unchanged
Unchanged
Macrocells flip-flop
status
Cleared to '0' by
internal Power-on
RESET
Depends on .re and .pr
equations
Depends on .re and .pr
equations
VM Register
Initialized, based on the Initialized, based on the
selection in PSDsoft
selection in PSDsoft
Unchanged
Configuration menu
Configuration menu
All other registers
Cleared to '0'
(1)
Cleared to '0'
Unchanged
1. The SR_cod and Periphmode Bits in the VM Register are always cleared to '0' on Power-on RESET or
Warm RESET.
143/181
Programming in-circuit using the JTAG serial interface
26
UPSD3212A, UPSD3212C, UPSD3212CV
Programming in-circuit using the JTAG serial
interface
The JTAG Serial Interface pins (TMS, TCK, TDI, and TDO) are dedicated pins on Port C
(see Table 104). All memory blocks (primary and secondary Flash memory), PLD logic, and
PSD module Configuration Register Bits may be programmed through the JTAG Serial
Interface block. A blank device can be mounted on a printed circuit board and programmed
using JTAG.
The standard JTAG signals (IEEE 1149.1) are TMS, TCK, TDI, and TDO. Two additional
signals, TSTAT and TERR, are optional JTAG extensions used to speed up Program and
Erase cycles.
By default, on a blank device (as shipped from the factory or after erasure), four pins on Port
C are the basic JTAG signals TMS, TCK, TDI, and TDO.
26.1
Standard JTAG Signals
At power-up, the standard JTAG pins are inputs, waiting for a JTAG serial command from an
external JTAG controller device (such as FlashLINK or Automated Test Equipment). When
the enabling command is received, TDO becomes an output and the JTAG channel is fully
functional. The same command that enables the JTAG channel may optionally enable the
two additional JTAG signals, TSTAT and TERR.
The RESET input to the uPS3200 should be active during JTAG programming. The active
RESET puts the MCU module into RESET mode while the PSD module is being
programmed. See Application Note AN1153 for more details on JTAG In-System
Programming (ISP).
UPSD321xx devices support JTAG In-System-Configuration (ISC) commands, but not
Boundary Scan. The PSDsoft Express software tool and FlashLINK JTAG programming
cable implement the JTAG In-System-Configuration (ISC) commands.
Table 104. JTAG port signals
26.2
Port C Pin
JTAG Signals
Description
PC0
TMS
Mode Select
PC1
TCK
Clock
PC3
TSTAT
Status (optional)
PC4
TERR
Error Flag (optional)
PC5
TDI
Serial Data In
PC6
TDO
Serial Data Out
JTAG extensions
TSTAT and TERR are two JTAG extension signals enabled by an “ISC_ENABLE” command
received over the four standard JTAG signals (TMS, TCK, TDI, and TDO). They are used to
speed Program and Erase cycles by indicating status on uPDS signals instead of having to
144/181
UPSD3212A, UPSD3212C, UPSD3212CV
Programming in-circuit using the JTAG serial interface
scan the status out serially using the standard JTAG channel. See Application Note
AN1153.
TERR indicates if an error has occurred when erasing a sector or programming a byte in
Flash memory. This signal goes Low (active) when an Error condition occurs, and stays Low
until an “ISC_CLEAR” command is executed or a chip Reset (RESET) pulse is received
after an “ISC_DISABLE” command.
TSTAT behaves the same as Ready/Busy described in Section 21.2.1: Ready/Busy (PC3).
TSTAT is High when the PSD module device is in READ mode (primary and secondary
Flash memory contents can be read). TSTAT is Low when Flash memory Program or Erase
cycles are in progress, and also when data is being written to the secondary Flash memory.
TSTAT and TERR can be configured as open-drain type signals during an “ISC_ENABLE”
command.
26.3
Security and Flash memory protection
When the Security Bit is set, the device cannot be read on a Device Programmer or through
the JTAG Port. When using the JTAG Port, only a Full Chip Erase command is allowed.
All other Program, Erase and Verify commands are blocked. Full Chip Erase returns the part
to a non-secured blank state. The Security Bit can be set in PSDsoft Express Configuration.
All primary and secondary Flash memory sectors can individually be sector protected
against erasures. The sector protect bits can be set in PSDsoft Express Configuration.
145/181
Initial delivery state
27
UPSD3212A, UPSD3212C, UPSD3212CV
Initial delivery state
When delivered from ST, the UPSD321xx devices have all bits in the memory and PLDs set
to '1.' The code, configuration, and PLD logic are loaded using the programming procedure.
Information for programming the device is available directly from ST. Please contact your
local sales representative.
146/181
UPSD3212A, UPSD3212C, UPSD3212CV
AC/DC parameters
These tables describe the AD and DC parameters of the UPSD321xx devices:
●
DC Electrical Specification
●
AC Timing Specification
●
PLD Timing
●
–
Combinatorial Timing
–
Synchronous Clock mode
–
Asynchronous Clock mode
–
Input Macrocell Timing
MCU module Timing
–
READ Timing
–
WRITE Timing
–
Power-down and RESET Timing
The following are issues concerning the parameters presented:
●
In the DC specification the supply current is given for different modes of operation.
●
The AC power component gives the PLD, Flash memory, and SRAM mA/MHz
specification. Figure 66 and Figure 67 show the PLD mA/MHz as a function of the
number of Product Terms (PT) used.
●
In the PLD timing parameters, add the required delay when Turbo Bit is '0.'
Figure 66. PLD ICC/frequency consumption (5 V range)
110
100
VCC = 5V
%)
90
BO
TUR
80
ON
(100
70
FF
)
BO
TUR
O
O
60
RB
50
ON
(25%
TU
ICC – (mA)
28
AC/DC parameters
40
30
F
20
BO
OF
PT 100%
PT 25%
R
TU
10
0
0
5
10
15
20
HIGHEST COMPOSITE FREQUENCY AT PLD INPUTS (MHz)
25
AI02894
147/181
AC/DC parameters
UPSD3212A, UPSD3212C, UPSD3212CV
Figure 67. PLD ICC/frequency consumption (3 V range)
60
VCC = 3V
TUR
ON (1
40
O
FF
30
5%)
(2
O ON
TU
RB
O
ICC – (mA)
)
00%
BO
50
20
TURB
10
PT 100%
PT 25%
F
BO
OF
R
TU
0
0
5
10
15
20
25
HIGHEST COMPOSITE FREQUENCY AT PLD INPUTS (MHz)
AI03100
Table 105. PSD module example, typ. power calculation at VCC = 5.0 V (Turbo mode
off)
Conditions
MCU clock frequency
= 12 MHz
Highest Composite PLD input frequency
(Freq PLD)
MCU ALE frequency (Freq ALE)
= 8 MHz
= 2 MHz
% Flash memory access
= 80%
% SRAM access
= 15%
% I/O access
= 5% (no additional power above base)
Operational modes
% Normal
= 40%
% Power-down mode
= 60%
Number of product terms used
148/181
(from fitter report)
= 45 PT
% of total product terms
= 45/182 = 24.7%
Turbo mode
= Off
UPSD3212A, UPSD3212C, UPSD3212CV
AC/DC parameters
Table 105. PSD module example, typ. power calculation at VCC = 5.0 V (Turbo mode
off) (continued)
Conditions
Calculation (using typical values)
= ICC(MCUactive) x %MCUactive + ICC(PSDactive) x %PSDactive + IPD(pwrdown) x
%pwrdown
ICC(MCUactive)
= 20mA
IPD(pwrdown)
= 250µA
ICC(PSDactive)
= ICC(ac) + ICC(dc)
= %flash x 2.5mA/MHz x Freq ALE
+ %SRAM x 1.5mA/MHz x Freq
ALE
ICC total
+ % PLD x (from graph using
Freq PLD)
= 0.8 x 2.5mA/MHz x 2MHz + 0.15 x
1.5mA/MHz x 2MHz + 24mA
= (4 + 0.45 + 24) mA
= 28.45mA
ICC total
= 20mA x 40% + 28.45mA x 40% + 250µA x 60%
= 8mA + 11.38mA + 150µA
= 19.53mA
This is the operating power with no Flash memory Erase or Program cycles in progress. Calculation
is based on all I/O pins being disconnected and IOUT = 0mA.
149/181
Maximum ratings
29
UPSD3212A, UPSD3212C, UPSD3212CV
Maximum ratings
Stressing the device above the rating listed in the Absolute Maximum Ratings” table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the Operating sections of
this specification is not implied. Exposure to Absolute Maximum Rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 106. Absolute maximum ratings
Symbol
Parameter
TSTG
Storage Temperature
TLEAD
Lead Temperature during Soldering (20 seconds max.)(1)
Max.
Unit
–65
125
°C
235
°C
VIO
Input and Output Voltage (Q = VOH or Hi-Z)
–0.5
6.5
V
VCC
Supply Voltage
–0.5
6.5
V
VPP
Device Programmer Supply Voltage
–0.5
14.0
V
VESD
Electrostatic Discharge Voltage (Human Body Model) 2
–2000
2000
V
1. IPC/JEDEC J-STD-020A
2. JEDEC Std JESD22-A114A (C1=100pF, R1=1500 Ω, R2=500 Ω)
150/181
Min.
UPSD3212A, UPSD3212C, UPSD3212CV
30
EMC characteristics
EMC characteristics
Susceptibility test are performed on a sample basis during product characterization.
30.1
Functional EMS (electromagnetic susceptibility)
Based on a simple running application on the product (toggling 2 LEDs through I/O ports),
the product is stressed by two electromagnetic events until a failure occurs (indicated by the
LEDs).
30.1.1
ESD
Electro-Static Discharge (positive and negative) is applied on all pins of the device until a
functional disturbance occurs. This test conforms with the IEC 1000-4-2 Standard.
30.1.2
FTB
A burst of Fast Transient voltage (positive and negative) is applied to VDD and VSS through a
100pF capacitor, until a functional disturbance occurs. This test conforms with the IEC
1000-4-2 Standard.
A device reset allows normal operations to be resumed. The test results are given in
Table 107, based on the EMS levels and classes defined in Application Note AN1709.
30.2
Designing hardened software to avoid noise problems
EMC characterization and optimization are performed at component level with a typical
application environment and simplified MCU software. It should be noted that good EMC
performance is highly dependent on the user application and the software in particular.
Therefore, it is recommended that the user applies EMC software optimization and
prequalification tests in relation with the EMC level requested for the user’s application.
30.2.1
Software recommendations
The software flowchart must include the management of ‘runaway’ conditions, such as:
30.2.2
●
Corrupted program counter
●
Unexpected reset
●
Critical data corruption (e.g., control registers)
Prequalification trials
Most of the common failures (unexpected reset and program counter corruption) can be
reproduced by manually forcing a low state on the RESET pin or the oscillator pins for 1
second.
To complete these trials, ESD stress can be applied directly on the device over the range of
specification values. When unexpected behavior is detected, the software can be hardened
to prevent unrecoverable errors occurring (see Application Note AN1015).
151/181
EMC characteristics
30.3
UPSD3212A, UPSD3212C, UPSD3212CV
Absolute maximum ratings (electrical sensitivity)
Based on three different tests (ESD, LU, and DLU) and using specific measurement
methods, the product is stressed in order to determine its performance in terms of electrical
sensitivity. For more details, refer to the Application Note AN1181.
30.3.1
Electro-static discharge (ESD)
Electro-Static discharges (a positive then a negative pulse separated by 1 second) are
applied to the pins of each sample according to each pin combination. The sample size
depends on the number of supply pins in the device (3 parts*(n+1) supply pin). The Human
Body Model is simulated (Table 108). This test complies with the JESD22-A114A Standard.
Table 107. EMS test results
Symbol
Parameter
Level/Class (1)
Conditions
Voltage limits to be applied on any VDD = 4V; TA = 25°C; fOSC =
I/O pin to induce a functional
40MHz; WDT off complies with
disturbance
IEC 1000-4-2
VFESD
3C
1. Data based on characterization results, not tested in production.
Table 108. ESD absolute maximum ratings
Symbol
Parameter
Conditions
Max. Value(1)
Unit
VESD(HBM)
Electro-static discharge voltage
(Human Body Model)
TA = 25°C
2000
V
1. Data based on characterization results, not tested in production
30.3.2
Latch-up
3 complementary static tests are required on 10 parts to assess the latch-up performance. A
supply overvoltage (applied to each power supply pin) and a current injection (applied to
each input, output, and configurable I/O pin) are performed on each sample. This test
conforms to the EIA/JESD 78 IC Latch-up Standard (see Table 109). For more details, refer
to the Application Note, AN1181.
30.3.3
Dynamic latch-up
Electro-static discharges (one positive then one negative test) are applied to each pin of 3
samples when the micro is running to assess the latch-up performance in dynamic mode.
Power supplies are set to the typical values, the oscillator is connected as near as possible
to the pins of the micro, and the component is put in reset mode. This test conforms to the
IEC 1000-4-2 and SAEJ1752/3 Standards (see Table 109). For more details, refer to the
Application Note, AN1181.
Table 109. Latch-up and dynamic latch-up electrical sensitivities
Symbol
LU
DLU
Parameter
Conditions
Level/class (1)
Static latch-up class
TA = 25°C
A
Dynamic latch-up class
VDD = 5 V; TA = 25°C; fOSC = 40 MHz
A
1. Class description: A Class is an STMicroelectronics internal specification. All of its limits are higher than the
JEDEC specifications. This means when a device belongs to “Class A,” it exceeds the JEDEC standard.
“Class B” strictly covers all of the JEDEC criteria (International standards).
152/181
UPSD3212A, UPSD3212C, UPSD3212CV
31
DC and AC parameters
DC and AC parameters
This section summarizes the operating and measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC Characteristic tables that
follow are derived from tests performed under the Measurement Conditions summarized in
the relevant tables. Designers should check that the operating conditions in their circuit
match the measurement conditions when relying on the quoted parameters.
Table 110. Operating conditions (5 V devices)
Symbol
Parameter
VCC
TA
Min.
Max.
Unit
Supply voltage
4.5
5.5
V
Ambient operating temperature (industrial)
–40
85
°C
0
70
°C
Min.
Max.
Unit
Supply voltage
3.0
3.6
V
Ambient operating temperature (industrial)
–40
85
°C
0
70
°C
Ambient operating temperature (commercial)
Table 111. Operating conditions (3 V devices)
Symbol
Parameter
VCC
TA
Ambient operating temperature (commercial)
Table 112. AC signal letters for timing
A
Address
C
Clock
D
Input Data
I
Instruction
L
ALE
N
RESET Input or Output
P
PSEN signal
Q
Output Data
R
RD signal
W
WR signal
M
Output Macrocell
1. Example: tAVLX = Time from Address Valid to ALE Invalid.
153/181
DC and AC parameters
UPSD3212A, UPSD3212C, UPSD3212CV
Table 113. AC signal behavior symbols for timing
t
Time
L
Logic Level Low or ALE
H
Logic Level High
V
Valid
X
No Longer a Valid Logic Level
Z
Float
PW
Pulse Width
1. Example: tAVLX = Time from Address Valid to ALE Invalid.
Figure 68. Switching waveforms – key
WAVEFORMS
INPUTS
OUTPUTS
STEADY INPUT
STEADY OUTPUT
MAY CHANGE FROM
HI TO LO
WILL BE CHANGING
FROM HI TO LO
MAY CHANGE FROM
LO TO HI
WILL BE CHANGING
LO TO HI
DON'T CARE
CHANGING, STATE
UNKNOWN
OUTPUTS ONLY
CENTER LINE IS
TRI-STATE
AI03102
Table 114. Major parameters
Parameters/conditions/
comments
5 V test
conditions
5.0 V value
3.3 V test
conditions
3.3 V
value
Unit
Operating voltage
–
4.5 to 5.5
–
3.0 to 3.6
V
Operating temperature
–
–40 to 85
–
–40 to 85
°C
MCU frequency
12 MHz (min) for USB;
8 MHz (min) for I2C
–
1 Min, 40
Max
–
1 Min, 24
Max
MHz
72
12 MHz MCU
clock, 6 MHz
PLD input
frequency,
2 MHz ALE
21
mA
25
12 MHz MCU
clock, 1 MHz
PLD input
frequency
7
mA
Active current, typical
(25°C operation; 80% Flash
and 15% SRAM accesses,
45 PLD product terms used;
PLD Turbo mode Off)
Idle current, typical
(CPU halted but some
peripherals active; 25°C
operation; 45 PLD product
terms used; PLD Turbo
mode Off)
154/181
24 MHz MCU
clock, 12 MHz
PLD input
frequency, 4 MHz
ALE
24 MHz MCU
clock, 12 MHz
PLD input
frequency
UPSD3212A, UPSD3212C, UPSD3212CV
DC and AC parameters
Table 114. Major parameters (continued)
Parameters/conditions/
comments
5 V test
conditions
5.0 V value
3.3 V test
conditions
3.3 V
value
Unit
Standby current, typical
(Power-down mode,
requires reset to exit mode;
without Low-Voltage Detect
(LVD) Supervisor)
180 µA with LVD
110
100 µA with LVD
60
µA
I/O sink/source current
Ports A, B, C, and D
VOL = 0.25 V
(max);
VOH = 3.9 V (min)
IOL = 8
(max);
IOH = –2
(min)
VOL = 0.15 V
(max);
VOH = 2.6 V (min)
IOL = 4
(max);
IOH = –1
(min)
mA
PLD macrocells (For
registered or combinatorial
logic)
–
16
–
16
–
PLD inputs (Inputs from
pins, macrocell feedback, or
MCU addresses)
–
69
–
69
–
PLD outputs (Output to pins
or internal feedback)
–
16
–
16
–
PLD propagation delay,
typical (PLD input to output,
Turbo mode)
–
15
–
22
ns
155/181
DC and AC parameters
UPSD3212A, UPSD3212C, UPSD3212CV
Table 115. DC characteristics (5 V devices)
Symbol
Parameter
Test conditions (in
addition to those in
Table 110)
Min.
VIH
Input high voltage (Ports 1,
2, 3, 4[Bits 7,6,5,4,3,1,0],
XTAL1, RESET)
4.5 V < VCC < 5.5 V
VIH1
Input high voltage (Ports A,
B, C, D, 4[Bit 2], USB+,
USB–)
VIL
VIL1
VOL
Unit
0.7 VCC
VCC +
0.5
V
4.5 V < VCC < 5.5 V
2.0
VCC +
0.5
V
Input low voltage (Ports 1,
2, 3, 4[Bits 7,6,5,4,3,1,0],
XTAL1, RESET)
4.5 V < VCC < 5.5 V
VSS– 0.5
Input low voltage
(Ports A, B, C, D, 4[Bit 2])
4.5 V < VCC < 5.5 V
–0.5
0.8
V
Input low voltage
(USB+, USB–)
4.5 V < VCC < 5.5 V
VSS– 0.5
0.8
V
0.3 VC
V
C
IOL = 20 µA
VCC = 4.5 V
0.01
0.1
V
IOL = 8 mA
VCC = 4.5 V
0.25
0.45
V
VOL1
Output low voltage
(Ports 1,2,3,4, WR, RD)
IOL = 1.6 mA
0.45
V
VOL2
Output low voltage
(Port 0, ALE, PSEN)
IOL = 3.2 mA
0.45
V
VOH
Output high voltage
(Ports A,B,C,D)
VOH2
Output high voltage (Port 0
in ext. Bus mode, ALE,
PSEN)
VLVR
Low Voltage RESET
VOP
XTAL open bias voltage
(XTAL1, XTAL2)
VLKO
VCC(min) for Flash Erase
and Program
IOH = –20 µA
VCC = 4.5 V
4.4
4.49
V
IOH = –2 mA
VCC = 4.5 V
2.4
3.9
V
IOH = –800 µA
2.4
V
IOH = –80 µA
4.05
V
0.1 V hysteresis
3.75
IOL = 3.2 mA
4.0
4.25
V
2.0
3.0
V
2.5
4.2
V
IIL
Logic '0' input current
(Ports 1,2,3,4)
VIN = 0.45 V
(0 V for Port 4[pin 2])
–10
–50
µA
ITL
Logic 1-to-0 transition
current (Ports 1,2,3,4)
VIN = 3.5 V
(2.5 V for Port 4[pin 2])
–65
–650
µA
VIN = VSS
–10
–55
µA
IRST
156/181
Max.
Output low voltage
(Ports A,B,C,D)
Typ.
Reset pin pull-up current
(RESET)
UPSD3212A, UPSD3212C, UPSD3212CV
DC and AC parameters
Table 115. DC characteristics (5 V devices) (continued)
Symbol
Parameter
Test conditions (in
addition to those in
Table 110)
Min.
Typ.
Max.
Unit
IFR
XTAL feedback resistor
current (XTAL1)
XTAL1 = VCC
XTAL2 = VSS
–20
–50
µA
ILI
Input leakage current
VSS < VIN < VCC
–1
1
µA
ILO
Output leakage current
0.45 < VOUT < VCC
–10
10
µA
250
µA
Power-down mode
VCC = 5.5 V
LVD logic disabled
LVD logic enabled
380
µA
20
30
mA
8
10
mA
30
38
mA
15
20
mA
40
62
mA
20
30
mA
IPD(1)
Active (12 MHz)
VCC = 5 V
Idle (12 MHz)
ICC_CPU
(2,3,6)
Active (24 MHz)
VCC = 5 V
Idle (24 MHz)
Active (40 MHz)
VCC = 5 V
Idle (40 MHz)
PLD_TURBO = Off,
f = 0 MHz(4)
0
PLD_TURBO = On,
f = 0 MHz
400
700
µA/PT
During Flash memory
WRITE/Erase Only
15
30
mA
Read-only, f = 0 MHz
0
0
mA
f = 0 MHz
0
0
mA
µA/PT(5)
PLD Only
ICC_PSD
(DC)(6)
Operating
supply current
Flash
memory
SRAM
PLD AC Base
ICC_PSD
(AC)(6)
Note 5
Flash memory AC adder
2.5
3.5
mA/MHz
SRAM AC adder
1.5
3.0
mA/MHz
1. IPD (Power-down mode) is measured with:
XTAL1=VSS; XTAL2=not connected; RESET=VCC; Port 0 =VCC; all other pins are disconnected. PLD not
in Turbo mode.
2. ICC_CPU (active mode) is measured with:
XTAL1 driven with tCLCH, tCHCL = 5 ns, VIL = VSS+0.5 V, VIH = Vcc – 0.5 V, XTAL2 = not connected;
RESET=VSS; Port 0=VCC; all other pins are disconnected. ICC would be slightly higher if a crystal oscillator
is used (approximately 1mA).
3. ICC_CPU (Idle mode) is measured with:
XTAL1 driven with tCLCH, tCHCL = 5 ns, VIL = VSS+0.5 V, VIH = VCC– 0.5 V, XTAL2 = not connected;
Port 0 = VCC;
4. RESET=VCC; all other pins are disconnected.
5. PLD is in non-Turbo mode and none of the inputs are switching.
6. See Figure 66 for the PLD current calculation.
7. I/O current = 0 mA, all I/O pins are disconnected.
157/181
DC and AC parameters
UPSD3212A, UPSD3212C, UPSD3212CV
Table 116. DC characteristics (3 V devices)
Symbol
Parameter
Test conditions (in
addition to those in
Table 111)
Min.
VIH
Input high voltage (Ports 1,
2, 3, 4[Bits 7,6,5,4,3,1,0], A,
B, C, D, XTAL1, RESET)
3.0 V < VCC < 3.6 V
VIH1
Input high voltage (Port
4[Bit 2])
VIL
VIL1
VOL
158/181
Max.
Unit
0.7VCC
VCC +
0.5
V
3.0 V < VCC < 3.6 V
2.0
VCC +
0.5
V
Input high voltage (Ports 1,
2, 3, 4[Bits 7,6,5,4,3,1,0],
XTAL1, RESET)
3.0 V < VCC < 3.6 V
VSS– 0.5
0.3
VCC
V
Input low voltage
(Ports A, B, C, D)
3.0 V < VCC < 3.6 V
–0.5
0.8
V
Input low voltage
(Port 4[Bit 2])
3.0 V < VCC < 3.6 V
VSS– 0.5
0.8
V
Output low voltage
(Ports A,B,C,D)
VOL1
Output low voltage
(Ports 1,2,3,4, WR, RD)
VOL2
Output low voltage
(Port 0, ALE, PSEN)
VOH
Output high voltage
(Ports A,B,C,D)
VOH2
Output high voltage (Port 0
in ext. Bus mode, ALE,
PSEN)
VLVR
Low voltage reset
VOP
XTAL open bias voltage
(XTAL1, XTAL2)
VLKO
VCC(min) for Flash Erase
and Program
Typ.
IOL = 20 µA
VCC = 3.0 V
0.01
0.1
V
IOL = 4 mA
VCC = 3.0 V
0.15
0.45
V
IOL = 1.6 mA
0.45
V
IOL = 100 µA
0.3
V
IOL = 3.2 mA
0.45
V
IOL = 200 µA
0.3
V
IOH = –20 µA
VCC = 3.0 V
2.9
2.99
V
IOH = –1 mA
VCC = 3.0 V
2.4
2.6
V
IOH = –800 µA
2.0
V
IOH = –80 µA
2.7
V
0.1 V hysteresis
2.3
IOL = 3.2 mA
2.5
2.7
V
1.0
2.0
V
1.5
2.2
V
IIL
Logic '0' input current
(Ports 1,2,3,4)
VIN = 0.45 V
(0 V for Port 4[pin 2])
–1
–50
µA
ITL
Logic 1-to-0 transition
current (Ports 1,2,3,4)
VIN = 3.5 V
(2.5 V for Port 4[pin 2])
–25
–250
µA
VIN = VSS
–10
–55
µA
XTAL1 = VCC
XTAL2 = VSS
–20
–50
µA
IRST
Reset pin pull-up current
(RESET)
IFR
XTAL feedback resistor
current (XTAL1)
ILI
Input leakage current
ILO
Output leakage current
VSS < VIN < VCC
–1
1
µA
0.45 < VOUT < VCC
–10
10
µA
UPSD3212A, UPSD3212C, UPSD3212CV
DC and AC parameters
Table 116. DC characteristics (3 V devices) (continued)
Symbol
IPD(1)
Parameter
Test conditions (in
addition to those in
Table 111)
Min.
Typ.
VCC = 3.6 V
LVD logic disabled
Power-down mode
LVD logic enabled
Active (12 MHz)
ICC_CPU
(2,3,6)
VCC = 3.6 V
Idle (12 MHz)
Active (24 MHz)
VCC = 3.6 V
Idle (24 MHz)
PLD Only
ICC_PSD
(DC)(6)
Operating
supply current
Flash
memory
Unit
110
µA
180
µA
8
10
mA
4
5
mA
15
20
mA
8
10
mA
PLD_TURBO = Off,
f = 0 MHz(4)
0
PLD_TURBO = On,
f = 0 MHz
200
400
µA/PT
During Flash memory
WRITE/Erase Only
10
25
mA
Read-only, f = 0 MHz
0
0
mA
f = 0 MHz
0
0
mA
SRAM
PLD AC base
ICC_PSD
(AC)(6)
Max.
µA/PT (5)
Note 5
Flash memory AC adder
1.5
2.0
mA/MHz
SRAM AC adder
0.8
1.5
mA/MHz
1. IPD (Power-down mode) is measured with:
XTAL1=VSS; XTAL2=not connected; RESET=VCC; Port 0 =VCC; all other pins are disconnected. PLD not
in Turbo mode.
2. ICC_CPU (active mode) is measured with:
XTAL1 driven with tCLCH, tCHCL = 5 ns, VIL = VSS+0.5 V, VIH = Vcc – 0.5 V, XTAL2 = not connected;
RESET=VSS; Port 0=VCC; all other pins are disconnected. ICC would be slightly higher if a crystal oscillator
is used (approximately 1 mA).
3. ICC_CPU (Idle mode) is measured with:
XTAL1 driven with tCLCH, tCHCL = 5 ns, VIL = VSS+0.5 V, VIH = VCC– 0.5 V, XTAL2 = not connected;
Port 0 = VCC;
4. RESET = VCC; all other pins are disconnected.
5. PLD is in non-Turbo mode and none of the inputs are switching.
6. See Figure 66 for the PLD current calculation.
7. I/O current = 0 mA, all I/O pins are disconnected.
159/181
DC and AC parameters
UPSD3212A, UPSD3212C, UPSD3212CV
Figure 69. External program memory Read cycle
tLLPL
tLHLL
ALE
tAVLL
tPLPH
tLLIV
tPLIV
PSEN
tPXAV
tLLAX
tPXIZ
tAZPL
PORT 0
INSTR
IN
A0-A7
tAVIV
A0-A7
tPXIX
A8-A11
PORT 2
A8-A11
AI06848
Table 117. External program memory AC characteristics (with the 5 V MCU module)
Symbol
Parameter(1)
40 MHz oscillator
Min.
Max.
Variable oscillator
1/tCLCL = 24 to 40 MHz
Min.
Unit
Max.
tLHLL
ALE pulse width
35
2 tCLCL – 15
ns
tAVLL
Address set-up to ALE
10
tCLCL – 15
ns
tLLAX
Address hold after ALE
10
tCLCL – 15
ns
tLLIV
ALE Low to valid instruction in
tLLPL
ALE to PSEN
10
tCLCL – 15
ns
tPLPH
PSEN pulse width
60
3 tCLCL – 15
ns
tPLIV
PSEN to valid instruction in
tPXIX
Input instruction hold after
PSEN
tPXIZ(2)
Input instruction float after
PSEN
tPXAV(2) Address valid after PSEN
tAVIV
Address to valid instruction in
tAZPL
Address float to PSEN
55
4 tCLCL – 45
30
0
3 tCLCL – 45
0
15
20
–5
ns
ns
tCLCL – 10
tCLCL – 5
70
ns
ns
ns
5 tCLCL – 55
–5
ns
ns
1. Conditions (in addition to those in Table 110, VCC = 4.5 to 5.5 V): VSS = 0 V; CL for Port 0, ALE and PSEN
output is 100 pF; CL for other outputs is 80 pF
2. Interfacing the UPSD321xx devices to devices with float times up to 20 ns is permissible. This limited bus
contention does not cause any damage to Port 0 drivers.
160/181
UPSD3212A, UPSD3212C, UPSD3212CV
DC and AC parameters
Table 118. External program memory AC characteristics (with the 3 V MCU module)
Symbol
Parameter
(1)
24 MHz
oscillator
Min.
Variable oscillator
1/tCLCL = 8 to 24 MHz
Max.
Min.
Unit
Max.
tLHLL
ALE pulse width
43
2 tCLCL – 40
ns
tAVLL
Address set-up to ALE
17
tCLCL – 25
ns
tLLAX
Address hold after ALE
17
tCLCL – 25
ns
tLLIV
ALE Low to valid instruction in
tLLPL
ALE to PSEN
22
tCLCL – 20
ns
tPLPH
PSEN pulse width
95
3 tCLCL – 30
ns
tPLIV
PSEN to valid instruction in
tPXIX
Input instruction hold after
PSEN
tPXIZ(2)
Input instruction float after
PSEN
tPXAV(2) Address valid after PSEN
tAVIV
Address to valid instruction in
tAZPL
Address float to PSEN
80
4 tCLCL – 87
60
ns
3 tCLCL – 65
0
ns
0
ns
32
tCLCL – 10
37
ns
tCLCL – 5
148
ns
5 tCLCL – 60
–10
ns
–10
ns
1. Conditions (in addition to those in Table 111, VCC = 3.0 to 3.6 V): VSS = 0 V; CL for Port 0, ALE and PSEN
output is 100 pF, for 5 V devices, and 50 pF for 3 V devices; CL for other outputs is 80 pF, for 5 V devices,
and 50 pF for 3 V devices)
2. Interfacing the UPSD321xx devices to devices with float times up to 35 ns is permissible. This limited bus
contention does not cause any damage to Port 0 drivers.
Table 119. External clock drive (with the 5 V MCU module)
Parameter(1)
Symbol
40 MHz oscillator
Min.
Max.
Variable oscillator
1/tCLCL = 24 to 40 MHz
Min.
Max.
Unit
tRLRH
Oscillator period
25
41.7
ns
tWLWH
High time
10
tCLCL –
tCLCX
ns
tLLAX2
Low time
10
tCLCL –
tCLCX
ns
tRHDX
Rise time
10
ns
tRHDX
Fall time
10
ns
1. Conditions (in addition to those in Table 110, VCC = 4.5 to 5.5 V): VSS = 0 V; CL for Port 0, ALE and PSEN
output is 100 pF; CL for other outputs is 80 pF
161/181
DC and AC parameters
UPSD3212A, UPSD3212C, UPSD3212CV
Table 120. External clock drive (with the 3 V MCU module)
Symbol
Parameter
24 MHz oscillator
(1)
Min.
Max.
Variable oscillator 1/tCLCL
= 8 to 24 MHz
Unit
Min.
Max.
41.7
125
ns
tRLRH
Oscillator period
tWLWH
High time
12
tCLCL – tCLCX
ns
tLLAX2
Low time
12
tCLCL – tCLCX
ns
tRHDX
Rise time
12
ns
tRHDX
Fall time
12
ns
1. Conditions (in addition to those in Table 111, VCC = 3.0 to 3.6 V): VSS = 0 V; CL for Port 0, ALE and PSEN
output is 100 pF, for 5 V devices, and 50 pF for 3 V devices; CL for other outputs is 80 pF, for 5 V devices,
and 50 pF for 3 V devices)
Figure 70. External data memory Read cycle
ALE
tLHLL
tWHLH
PSEN
tLLDV
tLLWL
tRLRH
RD
tRLDV
tAVLL
tLLAX2
tRLAZ
A0-A7 from
RI or DPL
PORT 0
tRHDZ
tRHDX
DATA IN
A0-A7 from PCL
INSTR IN
tAVWL
tAVDV
PORT 2
P2.0 to P2.3 or A8-A11 from DPH
A8-A11 from PCH
AI07088
Figure 71. External data memory Write cycle
ALE
tLHLL
tWHLH
PSEN
tLLWL
tWLWH
WR
tQVWX
tAVLL
tLLAX
PORT 0
A0-A7 from
RI or DPL
tWHQX
tQVWH
DATA OUT
A0-A7 from PCL
INSTR IN
tAVWL
PORT 2
P2.0 to P2.3 or A8-A11 from DPH
A8-A11 from PCH
AI07089
162/181
UPSD3212A, UPSD3212C, UPSD3212CV
DC and AC parameters
Table 121. External data memory AC characteristics (with the 5 V MCU module)
Symbol
Parameter
(1)
40 MHz oscillator
Min.
Max.
Variable oscillator
1/tCLCL = 24 to 40 MHz
Min.
Unit
Max.
tRLRH
RD pulse width
120
6 tCLCL – 30
ns
tWLWH
WR pulse width
120
6 tCLCL – 30
ns
tLLAX2
Address hold after ALE
10
tCLCL – 15
ns
tRHDX
RD to valid data in
tRHDX
Data hold after RD
tRHDZ
Data float after RD
38
2 tCLCL – 12
ns
tLLDV
ALE to valid data in
150
8 tCLCL – 50
ns
tAVDV
Address to valid data in
150
9 tCLCL – 75
ns
tLLWL
ALE to WR or RD
60
tCLCL + 15
ns
tAVWL
Address valid to WR or RD
70
tWHLH
WR or RD High to ALE High
10
tQVWX
Data valid to WR transition
5
tCLCL – 20
ns
tQVWH
Data set-up before WR
125
7 tCLCL – 50
ns
tWHQX
Data hold after WR
5
tCLCL – 20
ns
tRLAZ
Address float after RD
75
0
5 tCLCL – 50
0
90
3 tCLCL – 15
ns
4 tCLCL – 30
40
0
tCLCL – 15
ns
ns
tCLCL + 15
0
ns
ns
1. Conditions (in addition to those in Table 110, VCC = 4.5 to 5.5 V): VSS = 0 V; CL for Port 0, ALE and PSEN
output is 100 pF; CL for other outputs is 80 pF
163/181
DC and AC parameters
UPSD3212A, UPSD3212C, UPSD3212CV
Table 122. External data memory AC characteristics (with the 3 V MCU module)
Symbol
Parameter
(1)
Variable oscillator
1/tCLCL = 8 to 24 MHz
24 MHz oscillator
Min.
Max.
Min.
Unit
Max.
tRLRH
RD pulse width
180
6 tCLCL – 70
ns
tWLWH
WR pulse width
180
6 tCLCL – 70
ns
tLLAX2
Address hold after ALE
56
2 tCLCL – 27
ns
tRHDX
RD to valid data in
tRHDX
Data hold after RD
tRHDZ
Data float after RD
63
2 tCLCL – 20
ns
tLLDV
ALE to valid data in
200
8 tCLCL – 133
ns
tAVDV
Address to valid data in
220
9 tCLCL – 155
ns
tLLWL
ALE to WR or RD
75
tCLCL + 50
ns
tAVWL
Address valid to WR or RD
67
tWHLH
WR or RD High to ALE High
17
tQVWX
Data valid to WR transition
5
tCLCL – 37
ns
tQVWH
Data set-up before WR
170
7 tCLCL – 122
ns
tWHQX
Data hold after WR
15
tCLCL – 27
ns
tRLAZ
Address float after RD
118
5 tCLCL – 90
0
0
175
3 tCLCL – 50
ns
4 tCLCL – 97
67
tCLCL – 25
0
ns
ns
tCLCL + 25
0
ns
ns
1. Conditions (in addition to those in Table 111, VCC = 3.0 to 3.6 V): VSS = 0 V; CL for Port 0, ALE and PSEN
output is 100 pF, for 5 V devices, and 50 pF for 3 V devices; CL for other outputs is 80 pF, for 5 V devices,
and 50 pF for 3 V devices)
Table 123. A/D analog specification
Symbol
Test
condition
Min.
Typ.
Max.
Unit
AVREF
Analog power supply input
voltage range
VSS
VCC
V
VAN
Analog input voltage range
VSS – 0.3
AVREF + 0.3
V
IAVDD
Current following between VCC
and VSS
200
µA
CAIN
Overall accuracy
±2
l.s.b.
NNLE
Non-linearity error
±2
l.s.b.
NDNLE
Differential non-linearity error
±2
l.s.b.
NZOE
Zero-offset error
±2
l.s.b.
NFSE
Full scale error
±2
l.s.b.
NGE
Gain error
±2
l.s.b.
20
µs
tCONV
164/181
Parameter
Conversion time
at 8 MHz
clock
UPSD3212A, UPSD3212C, UPSD3212CV
DC and AC parameters
Figure 72. Input to output disable / enable
INPUT
tER
tEA
INPUT TO
OUTPUT
ENABLE/DISABLE
AI02863
Table 124. CPLD combinatorial timing (5 V devices)
Symbol
Parameter
Conditions
Min.
Max.
tPD(2)
CPLD input pin/feedback to
CPLD combinatorial output
20
tEA
CPLD input to CPLD output
enable
tER
PT Turbo Slew
Unit
aloc
off
rate(1)
+ 10
–2
ns
21
+ 10
–2
ns
CPLD input to CPLD output
disable
21
+ 10
–2
ns
tARP
CPLD register clear or
preset delay
21
+ 10
–2
ns
tARPW
CPLD register clear or
preset pulse width
tARD
CPLD array delay
+2
10
Any
macrocell
+ 10
11
ns
+2
ns
1. Fast Slew Rate output available on PA3-PA0, PB3-PB0, and PD2-PD1. Decrement times by given amount
2. tPD for MCU address and control signals refers to delay from pins on Port 0, Port 2, RD WR, PSEN and
ALE to CPLD combinatorial output (80-pin package only)
Table 125. CPLD combinatorial timing (3 V devices)
Symbol
Parameter
Conditions
Min.
Max.
tPD(2)
CPLD input pin/feedback to
CPLD combinatorial output
40
tEA
CPLD input to CPLD output
enable
tER
PT Turbo Slew
Unit
aloc
off rate(1)
+ 20
–6
ns
43
+ 20
–6
ns
CPLD input to CPLD output
disable
43
+ 20
–6
ns
tARP
CPLD register clear or
preset delay
40
+ 20
–6
ns
tARPW
CPLD register clear or
preset pulse width
tARD
CPLD array delay
+4
25
Any
macrocell
+ 20
25
ns
+4
ns
1. Fast Slew Rate output available on PA3-PA0, PB3-PB0, and PD2-PD1. Decrement times by given amount
2. tPD for MCU address and control signals refers to delay from pins on Port 0, Port 2, RD WR, PSEN and
ALE to CPLD combinatorial output (80-pin package only)
165/181
DC and AC parameters
UPSD3212A, UPSD3212C, UPSD3212CV
Figure 73. Synchronous clock mode timing – PLD
tCH
tCL
CLKIN
tS
tH
INPUT
tCO
REGISTERED
OUTPUT
AI02860
Table 126. CPLD macrocell synchronous clock mode timing (5 V devices)
Symbol
Parameter
Maximum frequency
external feedback
fMAX
Max.
PT Turbo Slew
Unit
Aloc Off rate(1)
1/(tS+tCO)
40.0
MHz
1/(tS+tCO–10)
66.6
MHz
1/(tCH+tCL)
83.3
MHz
Conditions
Maximum frequency
internal feedback (fCNT)
Maximum frequency
pipelined data
Min.
tS
Input setup time
12
tH
Input hold time
0
ns
tCH
Clock high time
Clock input
6
ns
tCL
Clock low time
Clock input
6
ns
tCO
Clock to output delay
Clock input
13
tARD
CPLD array delay
Any macrocell
11
tMIN
Minimum clock period
(2)
tCH+tCL
12
+2
+ 10
ns
–2
+2
ns
ns
ns
1. Fast Slew Rate output available on PA3-PA0, PB3-PB0, and PD2-PD1. Decrement times by given amount.
2. CLKIN (PD1) tCLCL = tCH + tCL.
166/181
UPSD3212A, UPSD3212C, UPSD3212CV
DC and AC parameters
Table 127. CPLD macrocell synchronous clock mode timing (3 V devices)
Symbol
Parameter
Maximum frequency
external feedback
fMAX
Maximum frequency
internal feedback (fCNT)
Maximum frequency
pipelined data
Conditions
Min.
Max.
PT
aloc
Turbo Slew
Unit
off
rate (1)
1/(tS+tCO)
22.2
MHz
1/(tS+tCO–10)
28.5
MHz
1/(tCH+tCL)
40.0
MHz
tS
Input setup time
20
tH
Input hold time
0
ns
tCH
Clock high time
Clock input
15
ns
tCL
Clock low time
Clock input
10
ns
tCO
Clock to output delay
Clock input
25
tARD
CPLD array delay
Any
macrocell
25
tMIN
Minimum clock period (2)
tCH+tCL
+4
+ 20
ns
–6
+4
25
ns
ns
ns
1. Fast Slew Rate output available on PA3-PA0, PB3-PB0, and PD2-PD1. Decrement times by given amount.
2. CLKIN (PD1) tCLCL = tCH + tCL.
Figure 74. Asynchronous Reset / Preset
tARPW
RESET/PRESET
INPUT
tARP
REGISTER
OUTPUT
AI02864
Figure 75. Asynchronous clock mode timing (product term clock)
tCHA
tCLA
CLOCK
tSA
tHA
INPUT
tCOA
REGISTERED
OUTPUT
AI02859
167/181
DC and AC parameters
UPSD3212A, UPSD3212C, UPSD3212CV
Table 128. CPLD macrocell asynchronous clock mode timing (5 V devices)
Symbol
fMAXA
Parameter
Conditions
Min
Max
PT Turbo Slew
Unit
aloc
off
rate
Maximum frequency
external feedback
1/(tSA+tCOA)
38.4
MHz
Maximum frequency
internal feedback (fCNTA)
1/(tSA+tCOA–
10)
62.5
MHz
Maximum frequency
pipelined data
1/(tCHA+tCLA)
71.4
MHz
tSA
Input setup time
7
+2
tHA
Input hold time
8
tCHA
Clock input high time
9
+ 10
ns
tCLA
Clock input low time
9
+ 10
ns
tCOA
Clock to output delay
ns
tARDA
CPLD array delay
tMINA
Minimum clock period
ns
21
Any macrocell
1/fCNTA
+ 10
11
+ 10
–2
+2
ns
ns
16
ns
Table 129. CPLD macrocell asynchronous clock mode timing (3 V devices)
Symbol
fMAXA
168/181
Parameter
Conditions
Min.
Max.
PT
aloc
Turbo
off
Slew
rate
Unit
Maximum frequency
external feedback
1/(tSA+tCOA)
21.7
MHz
Maximum frequency
internal feedback
(fCNTA)
1/(tSA+tCOA–
10)
27.8
MHz
Maximum frequency
pipelined data
1/(tCHA+tCLA)
33.3
MHz
tSA
Input setup time
10
+4
tHA
Input hold time
12
tCHA
Clock input high time
17
+ 20
ns
tCLA
Clock input low time
13
+ 20
ns
tCOA
Clock to output delay
tARD
CPLD array delay
tMINA
Minimum clock period
1/fCNTA
25
36
ns
ns
36
Any macrocell
+ 20
+ 20
+4
–6
ns
ns
ns
UPSD3212A, UPSD3212C, UPSD3212CV
DC and AC parameters
Figure 76. Input macrocell timing (product term clock)
t INH
t INL
PT CLOCK
t IS
t IH
INPUT
OUTPUT
t INO
AI03101
Table 130. Input macrocell timing (5 V devices)
Symbol
Parameter
Conditions
Min.
Max.
PT
aloc
Turbo
Unit
Off
tIS
Input setup time
(Note 1)
0
ns
tIH
Input hold time
(Note 1)
15
tINH
NIB input high time
(Note 1)
9
ns
tINL
NIB input low time
(Note 1)
9
ns
tINO
NIB input to combinatorial delay
(Note 1)
+ 10
34
+2
ns
+ 10
ns
1. Inputs from Port A, B, and C relative to register/ latch clock from the PLD. ALE/AS latch timings refer to
tAVLX and tLXAX.
Table 131. Input macrocell timing (3 V devices)
Symbol
Parameter
Conditions
Min.
Max.
PT
aloc
Turbo
Off
Unit
tIS
Input setup time
(Note 1)
0
ns
tIH
Input hold time
(Note 1)
25
tINH
NIB input high time
(Note 1)
12
ns
tINL
NIB input low time
(Note 1)
12
ns
tINO
NIB input to combinatorial delay
(Note 1)
+ 20
46
+4
ns
+ 20
ns
1. Inputs from Port A, B, and C relative to register/latch clock from the PLD. ALE latch timings refer to tAVLX
and tLXAX.
169/181
DC and AC parameters
UPSD3212A, UPSD3212C, UPSD3212CV
Table 132. Program, Write and Erase times (5 V devices)
Symbol
Parameter
Min.
Flash Program
Typ.
Max.
Unit
8.5
(1)
Flash Bulk Erase
(pre-programmed)
3
Flash Bulk Erase (not pre-programmed)
5
tWHQV3
Sector Erase (pre-programmed)
1
tWHQV2
Sector Erase (not pre-programmed)
2.2
tWHQV1
Byte Program
14
Program / Erase Cycles (per Sector)
tWHWLO
Sector Erase Time-Out
tQ7VQV
DQ7 Valid to Output (DQ7-DQ0) Valid (Data
Polling)(2)
s
30
s
s
30
s
s
150
100,000
µs
cycles
100
µs
30
ns
1. Programmed to all zero before erase.
2. The polling status, DQ7, is valid tQ7VQV time units before the data byte, DQ0-DQ7, is valid for reading.
Table 133. Program, Write and Erase times (3 V devices)
Symbol
Parameter
Min.
Flash Program
Flash Bulk
Erase(1)
Typ.
Max.
Unit
8.5
(pre-programmed)
3
Flash Bulk Erase (not pre-programmed)
5
tWHQV3
Sector Erase (pre-programmed)
1
tWHQV2
Sector Erase (not pre-programmed)
2.2
tWHQV1
Byte Program
14
Program / Erase Cycles (per Sector)
tWHWLO
Sector Erase Time-Out
tQ7VQV
DQ7 Valid to Output (DQ7-DQ0) Valid (Data
Polling)(2)
s
30
s
s
30
s
s
150
100,000
µs
cycles
100
µs
30
1. Programmed to all zero before erase.
2. The polling status, DQ7, is valid tQ7VQV time units before the data byte, DQ0-DQ7, is valid for reading.
170/181
ns
UPSD3212A, UPSD3212C, UPSD3212CV
DC and AC parameters
Figure 77. Peripheral I/O Read timing
ALE
ADDRESS
A/D BUS
DATA VALID
tAVQV (PA)
tSLQV (PA)
CSI
tRLQV (PA)
tRHQZ (PA)
RD
tDVQV (PA)
DATA ON PORT A
AI06610
Table 134. Port A peripheral data mode Read timing (5 V devices)
Symbol
Parameter
tAVQV–PA
Address valid to data valid
tSLQV–PA
CSI valid to data valid
tRLQV–PA
RD to data valid
tDVQV–PA
tRHQZ–PA
Condition
s
Min.
(Note 1)
(Note 2)
Max.
Turbo off
Unit
37
+ 10
ns
27
+ 10
ns
32
ns
Data in to data out valid
22
ns
RD to data high-Z
23
ns
1. Any input used to select Port A Data Peripheral mode.
2. Data is already stable on Port A.
Table 135. Port A peripheral data mode Read timing (3 V devices)
Symbol
Parameter
tAVQV–PA
Address valid to data valid
tSLQV–PA
CSI valid to data valid
tRLQV–PA
RD to data valid
tDVQV–PA
tRHQZ–PA
Conditions
(Note 1)
(Note 2)
Min.
Max.
Turbo off
Unit
50
+ 20
ns
37
+ 20
ns
45
ns
Data in to data out valid
38
ns
RD to data high-Z
36
ns
1. Any input used to select Port A Data Peripheral mode.
2. Data is already stable on Port A.
171/181
DC and AC parameters
UPSD3212A, UPSD3212C, UPSD3212CV
Figure 78. Peripheral I/O Write timing
ALE
ADDRESS
A / D BUS
DATA OUT
tWLQV
tWHQZ (PA)
(PA)
WR
tDVQV (PA)
PORT A
DATA OUT
AI06611
Table 136. Port A peripheral data mode Write timing (5 V devices)
Symbol
Parameter
Conditions
tWLQV–PA
WR to Data Propagation Delay
tDVQV–PA
Data to Port A Data Propagation Delay
tWHQZ–PA
WR Invalid to Port A Tri-state
Min.
Max.
Unit
25
ns
22
ns
20
ns
Max.
Unit
42
ns
38
ns
33
ns
(Note 1)
1. Data stable on Port 0 pins to data on Port A.
Table 137. Port A peripheral data mode Write timing (3 V devices)
Symbol
Parameter
Conditions
tWLQV–PA
WR to data propagation delay
tDVQV–PA
Data to Port A data propagation delay
tWHQZ–PA
WR invalid to Port A tri-state
Min.
(Note 1)
1. Data stable on Port 0 pins to data on Port A.
Figure 79. Reset (RESET) timing
VCC
VCC(min)
tNLNH-PO
Power-On Reset
tOPR
tNLNH
tNLNH-A
tOPR
Warm Reset
RESET
AI02866b
172/181
UPSD3212A, UPSD3212C, UPSD3212CV
DC and AC parameters
Table 138. Reset (RESET) timing (5 V devices)
Symbol
tNLNH
tNLNH–PO
tNLNH–A
tOPR
Parameter
Conditions
Min.
RESET active low time(1)
Power-on reset active low time
Warm RESET
(2)
Max.
Unit
150
ns
1
ms
25
μs
RESET high to operational device
120
ns
1. Reset (RESET) does not reset Flash memory Program or Erase cycles.
2. Warm RESET aborts Flash memory Program or Erase cycles, and puts the device in READ mode.
Table 139. Reset (RESET) timing (3 V devices)
Symbol
tNLNH
tNLNH–PO
tNLNH–A
tOPR
Parameter
Conditions
Min.
RESET active low time(1)
Max.
Unit
300
ns
Power-on reset active low time
1
ms
Warm RESET (2)
25
μs
RESET high to operational device
300
ns
1. Reset (RESET) does not reset Flash memory Program or Erase cycles.
2. Warm RESET aborts Flash memory Program or Erase cycles, and puts the device in READ mode.
Figure 80. ISC timing
t ISCCH
TCK
t ISCCL
t ISCPSU
t ISCPH
TDI/TMS
t ISCPZV
t ISCPCO
ISC OUTPUTS/TDO
t ISCPVZ
ISC OUTPUTS/TDO
AI02865
173/181
DC and AC parameters
UPSD3212A, UPSD3212C, UPSD3212CV
Table 140. ISC timing (5 V devices)
Symbol
Parameter
Conditions
Min.
Max.
Unit
tISCCF
Clock (TCK, PC1) frequency (except for PLD)
(Note 1)
20
MHz
tISCCH
Clock (TCK, PC1) high time (except for PLD)
(Note 1)
23
ns
tISCCL
Clock (TCK, PC1) low time (except for PLD)
(Note 1)
23
ns
tISCCFP Clock (TCK, PC1) frequency (PLD only)
(Note 2)
tISCCHP Clock (TCK, PC1) high time (PLD only)
(Note 2)
240
ns
tISCCLP Clock (TCK, PC1) low time (PLD only)
(Note 2)
240
ns
7
ns
5
ns
tISCPSU ISC port set-up time
tISCPH
ISC port hold-up time
2
MHz
tISCPCO ISC port clock to output
21
ns
tISCPZV ISC port high-impedance to valid output
21
ns
tISCPVZ ISC port valid output to high-impedance
21
ns
Max.
Unit
12
MHz
1. For non-PLD Programming, Erase or in ISC By-pass mode.
2. For Program or Erase PLD only.
Table 141. ISC timing (3 V devices)
Symbol
Parameter
Conditions
tISCCF
Clock (TCK, PC1) frequency (except for PLD)
(Note 1)
tISCCH
Clock (TCK, PC1) high time (except for PLD)
(Note 1)
40
ns
tISCCL
Clock (TCK, PC1) low time (except for PLD)
(Note 1)
40
ns
tISCCFP
Clock (TCK, PC1) frequency (PLD only)
(Note 2)
tISCCHP Clock (TCK, PC1) high time (PLD only)
Min.
2
(Note 2)
240
ns
(Note 2)
240
ns
tISCPSU ISC port set-up time
12
ns
tISCPH
5
ns
tISCCLP
Clock (TCK, PC1) low time (PLD only)
ISC port hold-up time
tISCPCO ISC port clock to output
30
ns
tISCPZV
ISC port high-impedance to valid output
30
ns
tISCPVZ
ISC port valid output to high-impedance
30
ns
1. For non-PLD Programming, Erase or in ISC By-pass mode.
2. For Program or Erase PLD only.
Figure 81. MCU module AC measurement I/O waveform
VCC – 0.5V
0.2 VCC + 0.9V
Test Points
0.2 VCC – 0.1V
0.45V
AI06650
1. AC inputs during testing are driven at VCC–0.5 V for a logic '1,' and 0.45 V for a logic '0.'
2. Timing measurements are made at VIH(min) for a logic '1,' and VIL(max) for a logic '0'.
174/181
MHz
UPSD3212A, UPSD3212C, UPSD3212CV
DC and AC parameters
Figure 82. PSD module AC float I/O waveform
VOH – 0.1V
VLOAD + 0.1V
Test Reference Points
VLOAD – 0.1V
0.2 VCC – 0.1V
VOL + 0.1V
AI06651
1. For timing purposes, a Port pin is considered to be no longer floating when a 100mV change from load
voltage occurs, and begins to float when a 100mV change from the loaded VOH or VOL level occurs
2. IOL and IOH ≥ 20mA
Figure 83. External clock cycle
Figure 84. Recommended oscillator circuits
1. C1, C2 = 30 pF ± 10 pF for crystals
2. For ceramic resonators, contact resonator manufacturer
3. Oscillation circuit is designed to be used either with a ceramic resonator or crystal oscillator. Since each
crystal and ceramic resonator
4. have their own characteristics, the user should consult the crystal manufacturer for appropriate values of
external components.
Figure 85. PSD module AC measurement I/O waveform
3.0V
Test Point
1.5V
0V
AI03103b
175/181
DC and AC parameters
UPSD3212A, UPSD3212C, UPSD3212CV
Figure 86. PSD module AC measurement load circuit
2.01 V
195 Ω
Device
Under Test
CL = 30 pF
(Including Scope and
Jig Capacitance)
AI03104b
Table 142. Capacitance
Symbol
CIN
COUT
Parameter
Input capacitance (for input pins)
Output capacitance (for
input/output pins)
Test conditions (1)
Typ.(2)
Max.
Unit
VIN = 0 V
4
6
pF
VOUT = 0 V
8
12
pF
1. Sampled only, not 100% tested.
2. Typical values are for TA = 25°C and nominal supply voltages.
176/181
UPSD3212A, UPSD3212C, UPSD3212CV
32
Package mechanical information
Package mechanical information
Figure 87. LQFP52 – 52-lead plastic thin, quad, flat package outline
Seating plane
A2
A
c
A1
ddd C
D
0.25 mm
.010 inch
Gage plane
D1
D2
27
39
L
k
L1
40
26
b
E2 E1
E
14
52
Pin 1 identification
13
1
e
DC_ME
1. Drawing is not to scale.
Table 143. LQFP52 – 52-lead plastic thin, quad, flat package mechanical data
inches(1)
millimeters
Symbol
Typ
Min
A
Max
Typ
Min
1.60
Max
0.063
A1
0.05
0.15
0.002
0.0059
A2
1.35
1.45
0.0531
0.0571
b
0.22
0.38
0.0087
0.015
C
0.09
0.2
0.0035
0.0079
0.0177
0.0295
0°
7°
D
12
0.4724
D1
10
0.3937
D2
7.8
0.3071
E
12
0.4724
E1
10
0.3937
E2
7.8
0.3071
e
0.65
0.0256
L
L1
0.45
0.75
1
0.0394
k
0°
ddd
0.100
7°
0.0039
1. Values in inches are converted from mm and rounded to 4 decimal digits.
177/181
Package mechanical information
UPSD3212A, UPSD3212C, UPSD3212CV
Figure 88. LQFP80 – 80-lead plastic thin, quad, flat package outline
D
D1
D3
A2
41
60
61
40
e
E3 E1 E
b
21
80
Pin 1
identification
1
20
A
ccc
L1
c
A1
k
L
9X_ME
1. Drawing is not to scale.
Table 144. LQFP80 – 80-lead plastic thin, quad, flat package mechanical data
inches(1)
millimeters
Symbol
Typ
Min
A
Max
Typ
1.600
A1
0.050
0.150
Max
0.0630
0.0020
0.0059
A2
1.400
1.350
1.450
0.0551
0.0531
0.0571
b
0.220
0.170
0.270
0.0087
0.0067
0.0106
0.090
0.200
0.0035
0.0079
0.0177
0.0295
0°
7°
C
D
14.000
0.5512
D1
12.000
0.4724
D3
9.500
0.3740
E
14.000
0.5512
E1
12.000
0.4724
E3
9.500
0.3740
e
0.500
0.0197
L
0.600
L1
1.000
k
ccc
0.450
0.750
0.0236
0.0394
0°
7°
0.080
1. Values in inches are converted from mm and rounded to 4 decimal digits.
178/181
Min
0.0031
UPSD3212A, UPSD3212C, UPSD3212CV
33
Part numbering
Part numbering
Table 145. Ordering information scheme
Example:
Device type
UPSD = Microcontroller PSD
UPSD
3
2
1
4
B
V
– 24
U
6
T
Family
3 = 8032 core
PLD size
2 = 16 Macrocells
SRAM Size
1 = 2 Kbytes
Main Flash memory size
2 = 64 Kbytes
3 = 128 Kbytes
4 = 256 Kbytes
IP mix
A = USB, I2C, PWM, DDC, ADC, (2) UARTs,
Supervisor (Reset Out, Reset In, LVD, WD)
B = I2C, PWM, DDC, ADC, (2) UARTs
Supervisor (Reset Out, Reset In, LVD, WD)
Operating voltage
blank = VCC = 4.5 to 5.5 V
V = VCC = 3.0 to 3.6 V
Speed
–24 = 24 MHz
–40 = 40 MHz
Package
T = 52-pin LQFP
U = 80-pin LQFP
Temperature range
1 = 0 to 70°C
6 = –40 to 85°C
Shipping options
F = ECOPACK® Package, Tape & Reel Packing
For other options, or for more information on any aspect of this device, please contact the ST Sales
Office nearest you.
179/181
Revision history
34
UPSD3212A, UPSD3212C, UPSD3212CV
Revision history
Table 146. Document revision history
180/181
Date
Revision
Changes
18-Dec-2002
1.0
First Issue
04-Mar-03
1.1
Updates: port information (Table 30); interface information (Figure 30,
Table 44); remove programming guide; PSD module information
(Table 82); PLD information (Figure 55); electrical characteristics
(Table 114, 115, 131, 132)
02-Sep-03
1.2
Update references for Product Catalog
03-Feb-04
2.0
Reformatted; correct package dimensions (Table 145)
02-July-04
3.0
Reformatted; add EMC characteristics information (Table 106, 107,
108)
04-Nov-04
4.0
Updates per requested data brief changes (Figure 3, 4; Table 1, 2,
113)
03-Dec-04
5.0
Add USB feature to document (Figure 2, 3, 4, 15, 16, 18, 20, 40, 41,
42, 43, 44, 45; Table 1, 2, 15, 16, 18, 19, 21, 23, 24, 25, 60, 61, 62,
63, 64, 65, 66, 67, 68, 69, 70, 71, 72, 73, 74, 75, 76, 77, 78, 79, 146)
21-Jan-2009
6.0
Removed battery backup feature and related SRAM Standby mode
information. Added Ecopack information and updated Section 32:
Package mechanical information on page 177.
UPSD3212A, UPSD3212C, UPSD3212CV
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
181/181