U2305B

U2305B VHF/ UHF-Tuner-IC Description This tuner IC requires a power supply of 5 V and performs the function of three separate oscillators an mixers, SAWF-driver, L.O.-output and tri-state band switch. This tuner IC is decigned for high performance tuners for TV, VCR and PCs. Features D 5 V supply voltage D Frequency range from 48 to 860 MHz D Band A: balanced high impedance mixer input and amplitude controlled oscillator D Balanced L. O.-outputs for prescalers or PLL D SAW filter driver with low impedance output D Voltage regulator for stable operating characteristics D ESD protection on all pins except oscillator pins and RF-inputs D Band B + C: balanced low impedance mixer input and symmetrical oscillator Benefits D The integration of 3 bands and the small SSO28 package allows to design very small and economical 3-band tuners with high performance. Block Diagram 1 3 4 657 8 10 9 11 19 2 Osc. A Osc. B Osc. C VoltageStabilizer Band-Switch 12 L.O. 27 28 Mixer-Output SAW-Driver 17 18 14 13 RF Band A 25 24 23 Band B 22 26 21 Band C 12504 20 16 15 Figure 1. Block diagram TELEFUNKEN Semiconductors Rev. A1, 10-Sep-96 1 (8) Preliminary Information U2305B Pin Description Osc A, base GND (common) Osc A, coll. Osc B, base Osc B, coll. Osc B, coll. Osc B, base Osc C, base Osc C, coll. 1 2 3 4 5 6 7 8 9 28 L.O. out 27 L.O. out 26 GND (RF) 25 RF in, A 24 RF in, A 23 RF in, B 22 RF in, B 21 RF in, C Pin 1 2 3 4, 7 5, 6 8, 11 9, 10 12 13, 14 15, 16 17, 18 19 20, 21 22, 23 24, 25 26 27, 28 Symbol Osc A, base GND (common) Osc A, coll. Osc B, base Osc B, coll. Osc C, base Osc C, coll. Band sw. SAWF, out SAWF, inp. Mix out VS RF in, C RF in, B RF in, A GND (RF) L.O. out Function Oscillator band A, base Ground, common Oscillator band A, collector Oscillator band B, bases Oscillator band B, collectors Oscillator band C, bases Oscillator band C, collectors Tri-state band switch SAW filter driver outputs SAW filter driver inputs Mixer outputs, open collector Supply voltage Vs RF inputs, band C RF inputs, band B RF inputs, band A Ground, RF part L.O.-outputs 20 RF in, C 19 18 17 16 15 95 10886 Osc C, coll. 10 Osc C, base Band sw. SAWF, out SAWF, out 11 12 13 14 VS Mix out Mix out SAWF, inp. SAWF, inp. Ordering Information Extended Type Number U2305B-AFSG3 Package SSO28 Remarks Taped and reeled 2 (8) Preliminary Information TELEFUNKEN Semiconductors Rev. A1, 10-Sep-96 U2305B Absolute Maximum Ratings All voltages are referred to GND, Pin 2 Parameters Supply voltage RF inputs IF outputs Tri-state switch voltage Junction temperature Storage temperature Pin 19 Pin (20-25) Pin 17-18 Pin 12 Symbol VS Min. Typ. Max. 5.25 VS 5.5 VS 125 125 Unit V V V V °C °C ViTRI Tj Tstg –40 Operating Range All voltages are referred to GND, Pin 2 Parameters Supply voltage Ambient temperature Test Conditions / Pins Pin 17-19 Symbol VS Tamb Min 4.5 –25 Typ 5.0 Max 5.25 75 Unit V °C Thermal Resistance Parameters Junction ambient Package SSO28 soldered to PCB (see layout page 5) Symbol RthJA Typ 128 Unit K/W Electrical Characteristics Test conditions (unless otherwise specified): Vs = 5 V. Tamb = 25 °C. Reference point Pin 2. Referred to test circuit page 5. Parameters Test Conditions / Pins Supply voltage Pin 17-19 Supply current Pin 17-19 Band switch Voltage band A Pin 12 Voltage band B Pin 12 Voltage band C Pin 12 Switching current VSW = 5 V Pin 12 LO output LO level each output RL = 50 W Pin 27, 28 SAW filter driver fi = 36 MHz Input impedance Pin 15, 16 Output impedance Pin 13, 14 Voltage gain Pin 15, 16 → 13, 14 Symbol VS IS VSWA VSWB VSWC ISW PLO ZiSAW ZoSAW GvSAW Min. 4.5 Typ. 5.0 42 Max. 5.25 Unit V mA VS VS VS mA dBm Ohm Ohm dB 0 25% 55% 20% 50% 100% 100 –17 450 70 17 –25 TELEFUNKEN Semiconductors Rev. A1, 10-Sep-96 3 (8) Preliminary Information U2305B Electrical Characteristics (continued) Parameters Band A Input frequency range Input impedance Gain (note 4) Noise figure DSB (note 2) Test Conditions / Pins Pin 24 Pin 24 Pin I/P to O/P Pin I/P to O/P fiA = 50 MHz fiA = 150 MHz Each carrier fiA = 71 MHz Pin I/P fiA = 71 MHz Pin I/P Figure 3 Pin 22, 23 Pin 22, 23 Pin I/P to O/P Pin I/P to O/P fiB = 200 MHz fiB = 450 MHz Each carrier fiB = 300 MHz Pin I/P Symbol fiA S11A GA NF NF ViA ViA fiA S11B GB NF NF ViB fiC S11C GC NF NF ViC 470 32 10.5 11.5 –28 170 see Fig. 3 32 9.5 10 –28 860 Min 48 28 11.5 12 –23 –22 470 Typ Max 170 Unit MHz dB dB dB dBm dBm MHz dB dB dB dBm MHz dB dB dB dBm Input level for (note 3): IM3 (interm. of 3rd order IM2 (interm. of 2nd order) Band B (note 1) Input frequency range Input impedance Gain (note 4) Noise figure DSB (note 2) Input level for (note 3): IM3 (interm. of 3rd order) Band C (note 1) Input frequency range Input impedance Gain Noise figure DSB (note 2) Pin 20, 21 Pin 20, 21 Pin I/P to O/P Pin I/P to O/P fiC = 500 MHZ fiC = 800 MHz Input level for IM3 Each carrier (interm. of 3rd order, note 3) fiC = 600 MHz Pin I/P Figure 3 Notes 1) 2) 3) 4) The RF inputs B and C are symmetrical driven by means of a hybrid for 180° phase shifting, consequently the source impedance is 100 W. All other impedance for RF tests is 50 W. The noise figure (NF) is the value for double-side-band measurement. The intermodulation test (2-carrier-method) which is made on IF-centre is in reference to a signal-to-IM ratio of 60 dB. Gain is the ratio of the voltage at the primary coil of L5 to the available voltage at the input. 4 (8) Preliminary Information TELEFUNKEN Semiconductors Rev. A1, 10-Sep-96 U2305B Test and Principle Application Circuit Hybrids 0 / 180 degree with 50 ohms Z(in) and 100 ohms (2x50) Z(out) I/P Band C UHF I/P Band B VHFH I/P Band A VHFL 180D 180D V(b) 10n L.O. 100p 100p 1n 1n 1n 1n 1n 1n IF : PC 38.9 MHz SC 33.4 MHz L.O. 25 21 17 U2305B 1 Air Coils 0.6 mm enamelled copper wire L1 L2 L3 L4 8 Wdg. 3.0 mm 0 3 2.5 3 2.5 3 2.5 1p 18 2p TOKO–Coils L5 t.b.d. L6 t.b.d. L1 BB620 BB619 82p 1k 8p2 18k 10n 18k 18k V(Diode) 100p BB515 18k 1n 68p 2k2 L4 2p2 2p7 2p7 L2 2p2 1p0 1p0 1p0 L3 1p0 L6 L6 5 9 13 The output–voltage of the IF is calculated back to the primary circuit of L5 L5 1n 15p 1n IF–Out O/P V(Band) Figure 2. Test and principle application circuit PCB for the RthJA-Measurement Material: 35 mm one-sided Cu-coated epoxy PCB, 40 mm 40 mm 1.5 mm 95 10719 Figure 3. PCB for the RthJA-measurement TELEFUNKEN Semiconductors Rev. A1, 10-Sep-96 5 (8) Preliminary Information U2305B Input Impedance Mixer Band A (S11A), B and C (S11B/C) j 0.5j 2j 0.2j –0.2j 1 –0.5j 95 9928 –j Figure 4. Input impedance mixer band A (S11A), B and C (S11B/C) 1) VHF-low Normalised to 50 W, measuring range 45 MHz to 750 MHz. VHF-high and UHF Normalised to 50 W, measuring range 45 MHz to 1045 MHz. Both inputs are driven symmetrical. The output impedance of hybrid is 100 W,the measured levels are then calculated in reference to 50 W. 2) 6 (8) Preliminary Information ÁÁÁÁ ÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁ ÁÁ ÁÁÁ 0 0.2 45 MHz 0.5 1 2 750 MHz Z0 = 50 W –2j TELEFUNKEN Semiconductors Rev. A1, 10-Sep-96 Á Á Á Á ÁÁ ÁÁÁÁÁÁÁ Á ÁÁ ÁÁÁÁÁ Á ÁÁÁÁÁ ÁÁÁÁ ÁÁ ÁÁÁÁ ÁÁ ÁÁÁÁÁ Á 845 MHz 1045 MHz 2 645 MHz 5j 445 MHz 245 MHz 5 1 45 MHz 250 MHz 500 MHz –5j U2305B Package Dimensions Super small outline plastic package, 28 pin – SSO28 Dimensions in mm 95 10721 TELEFUNKEN Semiconductors Rev. A1, 10-Sep-96 7 (8) Preliminary Information U2305B Ozone Depleting Substances Policy Statement It is the policy of TEMIC TELEFUNKEN microelectronic GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances ( ODSs). The Montreal Protocol ( 1987) and its London Amendments ( 1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. TEMIC TELEFUNKEN microelectronic GmbH semiconductor division has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2 . Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency ( EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C ( transitional substances ) respectively. TEMIC can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use TEMIC products for any unintended or unauthorized application, the buyer shall indemnify TEMIC against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. TEMIC TELEFUNKEN microelectronic GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 ( 0 ) 7131 67 2831, Fax number: 49 ( 0 ) 7131 67 2423 8 (8) Preliminary Information TELEFUNKEN Semiconductors Rev. A1, 10-Sep-96