MBR10H90CT

MBR10H100CT, MBRF10H100CT & MBRB10H100CT Series New Product Vishay Semiconductor Rev. Voltage 90 to 100V Forward Current 10A Dual High-Voltage Schottky Rectifiers ITO-220AB (MBRF10H90CT, MBRF10H100CT) 0.405 (10.27) 0.383 (9.72) 0.188 (4.77) 0.172 (4.36) 0.110 (2.80) 0.100 (2.54) TO-220AB (MBR10H90CT, MBR10H100CT) 0.415 (10.54) MAX. 0.154 (3.91) 0.370 (9.40) 0.360 (9.14) 0.148 (3.74) 0.113 (2.87) 0.103 (2.62) 0.145 (3.68) 0.135 (3.43) 0.410 (10.41) 0.390 (9.91) 1 0.160 (4.06) 0.140 (3.56) PIN 2 3 0.603 (15.32) 0.573 (14.55) 0.560 (14.22) 0.530 (13.46) 0.055 (1.39) 0.045 (1.14) 0.185 (4.70) 0.175 (4.44) 0.600 (15.5) 0.580 (14.5) PIN 1 2 3 0.140 (3.56) DIA. 0.130 (3.30) 0.131 (3.39) DIA. 0.122 (3.08) 0.676 (17.2) 0.646 (16.4) 0.350 (8.89) 0.330 (8.38) 0.191 (4.85) 0.171 (4.35) 0.060 (1.52) PIN 1 PIN 3 PIN 2 0.635 (16.13) 0.625 (15.87) 0.350 (8.89) 0.330 (8.38) 0.110 (2.80) 0.100 (2.54) 1.148 (29.16) 1.118 (28.40) 0.110 (2.79) 0.100 (2.54) 0.560 (14.22) 0.530 (13.46) 0.105 (2.67) 0.095 (2.41) 0.037 (0.94) 0.027 (0.69) 0.022 (0.55) 0.014 (0.36) PIN 1 PIN 3 PIN 2 CASE 0.105 (2.67) 0.095 (2.41) 0.104 (2.65) 0.096 (2.45) 0.035 (0.90) 0.028 (0.70) 0.205 (5.20) 0.195 (4.95) 0.022 (0.56) 0.014 (0.36) Dimensions in inches and (millimeters) 0.205 (5.20) 0.195 (4.95) TO-263AB (MBRB10H90CT, MBRB10H100CT) 0.411 (10.45) 0.380 (9.65) 0.190 (4.83) 0.160 (4.06) 0.055 (1.40) 0.045 (1.14) 0.42 (10.66) 0.245 (6.22) MIN K Mounting Pad Layout TO-263AB 0.63 (17.02) 0.33 (8.38) 0.360 (9.14) 0.320 (8.13) 1 K 2 0.624 (15.85) 0.591 (15.00) 0.055 (1.40) 0.047 (1.19) 0-0.01 (0-0.254) 0.110 (2.79) 0.090 (2.29) 0.037 (0.940) 0.027 (0.686) PIN 1 PIN 2 K - HEATSINK 0.021 (0.53) 0.014 (0.36) 0.140 (3.56) 0.110 (2.79) 0.08 (2.032) 0.24 (6.096) 0.12 (3.05) 0.105 (2.67) 0.095 (2.41) 0.205 (5.20) 0.195 (4.95) Mechanical Data Features • Plastic package has Underwriters Laboratory Flammability Classification 94V-0 • Dual rectifier construction, positive center tap • Metal silicon junction, majority carrier conduction • Low power loss, high efficiency • Guardring for overvoltage protection • For use in low voltage, high frequency inverters, free wheeling, and polarity protection applications Document Number 88668 24-Apr-03 Case: JEDEC TO-220AB, ITO-220AB & TO-263AB molded plastic body Terminals: Plated leads, solderable per MIL-STD-750, Method 2026 High temperature soldering guaranteed: 250°C/10 seconds, 0.25" (6.35mm) from case Polarity: As marked Mounting Position: Any Mounting Torque: 10 in-lbs maximum Weight: 0.08oz., 2.24g www.vishay.com 1 MBR10H100CT, MBRF10H100CT & MBRB10H100CT Series Vishay Semiconductors formerly General Semiconductor Maximum Ratings Parameter (TC = 25°C unless otherwise noted) Symbol VRRM VRWM VDC IF(AV) MBR10H90CT 90 90 90 10 5 150 0.5 MBR10H100CT 100 100 100 Unit V V V A Maximum repetitive peak reverse voltage Working peak reverse voltage Maximum DC blocking voltage Maximum average forward rectified current Total device at TC = 105°C Per leg Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) per leg Peak repetitive reverse current per leg at tp = 2µs, 1KHZ Voltage rate of change (rated VR) Operating junction and storage temperature range RMS Isolation voltage (MBRF type only) from terminals to heatsink with t = 1 second, RH ≤ 30% IFSM IRRM dv/dt TJ, TSTG VISOL A A V/µs °C V 10,000 –65 to +175 4500 3500 (2) 1500 (3) (1) Electrical Characteristics (TC = 25°C unless otherwise noted) Parameter Maximum instantaneous forward voltage per leg(4) at at at at IF = IF = IF = IF = 5.0A, TJ = 25°C 5.0A, TJ = 125°C 10A, TJ = 25°C 10A, TJ = 125°C TJ = 25°C TJ = 100°C Symbol Value 0.76 0.61 0.85 0.71 3.5 4.5 Unit VF V µA mA Maximum reverse current per leg at working peak reverse voltage (Note 4) IR Thermal Characteristics (TC = 25°C unless otherwise noted) Parameter Typical thermal resistance per leg Symbol RθJC MBR 2.2 MBRF 4.2 MBRB 2.2 Unit O C/W Notes: (1) Clip mounting (on case), where lead does not overlap heatsink with 0.110” offset (2) Clip mounting (on case), where leads do overlap heatsink (3) Screw mounting with 4-40 screw, where washer diameter is ≤ 4.9 mm (0.19”) (4) Pulse test: 300µs pulse width, 1% duty cycle Ordering Information Product MBR10H90CT, MBR10100CT MBRF10H90CT, MBRF10100CT MBRB10H90CT, MBRB10100CT Case TO-220AB ITO-220AB TO-263AB Package Code 45 45 31 45 81 Package Option Anti-Static tube, 50/tube, 2K/carton Anti-Static tube, 50/tube, 2K/carton 13” reel, 800/reel, 4.8K/carton Anti-Static tube, 50/tube, 2K/carton Anti-Static 13” reel, 800/reel, 4.8K/carton www.vishay.com 2 Document Number 88668 24-Apr-03 MBR10H100CT, MBRF10H100CT & MBRB10H100CT Series Vishay Semiconductors formerly General Semiconductor Ratings and Characteristic Curves (T 6.0 A = 25°C unless otherwise noted) Fig. 1 – Forward Derating Curve Per Leg 175 Fig. 2 – Maximum Non-Repetitive Peak Forward Surge Current Per Leg Peak Forward Surge Current (A) TJ = TJ max. 8.3ms Single Half Sine-Wave (JEDEC Method) Average Forward Current (A) 5.0 150 4.0 125 100 75 50 25 3.0 2.0 1.0 0 0 25 50 75 100 125 150 175 1 10 100 Case Temperature (°C) Number of Cycles at 60 HZ Fig. 3 – Typical Instantaneous Forward Characteristics Per Leg IF -- Instantaneous Forward Current (A) 100 TJ = 175°C 10 10000 Fig. 4 – Typical Reverse Characteristics Per Leg 1000 TJ = 150°C 125°C IR -- Instantaneous Reverse Current (µA) TJ = 150°C 100 100°C 1.0 TJ = 125°C TJ = 100°C 10 1 0.1 25°C 0.1 TJ = 25°C TJ = – 40°C 0.1 0.3 0.5 0.7 0.9 1.1 0.01 0.01 0 20 40 60 80 100 Percent of Rated Peak Reverse Voltage (%) Fig. 5 – Typical Junction Capacitance Per Leg 1000 100 Fig. 6 – Typical Transient Thermal Impedance Per Leg Transient Thermal Impedance (°C/W) Junction Capacitance (pF) 10 100 1 10 0.1 1 10 100 0.1 0.01 0.1 1 10 Reverse Voltage (V) Document Number 88668 24-Apr-03 t -- Pulse Duration (sec.) www.vishay.com 3