LCE80PS05

LCE80 Series AC-DC Power Supplies 80 Watts • Constant voltage, constant current mode • Suitable for lighting and display applications • Harmonics class C • ITE & household approvals • LPS for 12V and above • 2” by 4” footprint • Class I & class II operation • Less than 0.5W no load input power • 3 year warranty Dimensions: LCE80: 4.00 x 2.00 x 1.10” (101.6 x 50.8 x 27.9 mm) Models & Ratings Output Power Output Voltage Output Current 60 W 5.0 V 80 W 12.0 V 80 W Ripple & Noise Efficiency(1) Model Number 12.00 A 50 mV % LCE80US05 6.67 A 120 mV % LCE80US12 15.0 V 5.33 A 120 mV % LCE80US15 80 W 20.0 V 4.00 A 120 mV % LCE80US20 80 W 24.0 V 3.33 A 120 mV % LCE80US24 80 W 30.0 V 2.67 A 240 mV % LCE80US30 80 W 36.0 V 2.22 A 240 mV % LCE80US36 80 W 42.0 V 1.90 A 240 mV % LCE80US42 80 W 48.0 V 1.67 A 240 mV % LCE80US48 80 W 54.0 V 1.48 A 240 mV % LCE80US54 Notes 1. Minimum average efficiencies measured at 25%, 50%, 75% & 100% of 80W load and 230 VAC input. Summary Characteristic Input Range Minimum Typical Maximum Units Notes & Conditions 85 115/230 305 VAC Derate load from 100% at 90 VAC to 90% at 85 VAC No Load Input Power 0.5 Efficiency Operating Temperature 1 93 -20 +70 EMC Conducted: EN55032, Class B, Radiated: EN55032, Class B Safety Approvals CB/EN/UL/CSA for ITE and CB for household W % 230 VAC (see fig.1 & 2) °C See derating curve (fig.3) www.xppower.com LCE80 Series AC-DC Power Supplies Input Characteristic Minimum Typical Maximum Units Notes & Conditions Input Voltage - Operating 85 115/230 305 VAC Derate output from 100% at 90VAC to 90% at 85VAC and 85% at 80 VAC. Input Frequency 47 50/60 63 Hz Input Current - Full Load A 115/230 VAC Inrush Current A Earth Leakage Current µA 230 VAC cold start, 25 ºC 115/230 VAC/50 Hz (Typ), 264 VAC/60 Hz (Max) No load Input Power Input Protection 0.5 W F3.15 A/250 V Internal fuse fitted in line and neutral. Output - Main Output Characteristic Output Voltage - V1 Minimum Typical 5 Initial Set Accuracy Output Voltage Adjustment Minimum Load ±5 Units Notes & Conditions 54 VDC See Models and Ratings table ±0.5 % ±10 0 Start Up Delay Hold Up Time Maximum 2 20 None A No minimum load required s 115/230 VAC full load. ms Drift 50% load, 115/230 VAC % Min at full load, 115 VAC ±0.02 % After 20 min warm up Line Regulation ±1 % 90-264 VAC Load Regulation ±1 % 0-95% load, 5% in constant current mode Transient Response 4 % Recovery within 1% in less than 500 µs or a 50-75% and 75-50% load step Over/Undershoot 7 % Full load 50/120/200 mV pk-pk 140 % Ripple & Noise Overvoltage Protection Overload Protection 110 100 105 % I nom 0.02 %/˚C Short Circuit Protection 5V/12-24V/30-54V. 20 MHz bandwidth and 10 µF electrolytic capacitator in parallel with 0.1 µF ceramic capacitator. Vnom, recycle input to reset Constant current down to 45% of nominal voltage. See fig. 1. Trip & Restart Temperature Coefficient Output Characteristics Figure 1 Constant Voltage Output Voltage (%) 100 Constant Current 45 Hiccup Region 0 0 Load 95-105% www.xppower.com 2 LCE80 Series AC-DC Power Supplies General Characteristic Minimum Typical Maximum Units % Efficiency Isolation: Input to Output Input to Ground Output to Ground 3000 VAC 1500 VAC Notes & Conditions 230 VAC (see fig. 2 & 3) VAC Switching Frequency 50 Power Density Mean Time Between Failure Weight 95 kHz 9 W/in3 300 kHrs 0.32 (145) lb(g) Main converter MIL-HDBK-217F, Notice 2 +25 °C GB Efficiency Vs Load Figure 2 LCE80PS12 100% 95% Efficiency 90% 85% 115Vac 80% 230Vac 75% 70% 65% 60% 10 20 30 40 50 60 70 80 90 100 Load (%) Figure 3 LCE80PS24 100% 95% Efficiency 90% 85% 115Vac 80% 230Vac 75% 70% 65% 60% 10 20 30 40 50 60 70 Load (%) 3 www.xppower.com 80 90 100 LCE80 Series AC-DC Power Supplies Environmental Characteristic Maximum Units Operating Temperature Minimum -40 Typical +70 °C Storage Temperature -40 +85 Cooling 10 Humidity 5 Operating Altitude Notes & Conditions See derating curve, fig.4 °C CFM Forced-cooled > 100W 95 %RH Non-condensing 5000 m Shock ±3 x 30g shocks in each plane, total 18 shocks. 30g = 11ms (+/- 0.5msecs), half sine. Conforms to EN60068-2-27 Vibration Single axis 10-500 Hz at 2g sweep and endurance at resonance in all 3 planes. Conforms to EN60068-2-6 Temperature Derating Curve 100 50 0 -40 High Line Only Output Load (%) Figure 4 -30 0 EMC: Emissions Phenomenon Standard Test Level Conducted EN55032 Class B Radiated Harmonic Current Voltage Functions +50 +70 Ambient Temperature (ºC) EN55032 Class B EN61000-3-2 Class A, C Criteria Notes & Conditions Class C for 50W load and above EN61000-3-3 EMC: Immunity Phenomenon Low Voltage PSU EMC Standard Test Level Criteria EN61204-3 High severity level as below ESD EN61000-4-2 3 A Radiated EN61000-4-3 3 A A EFT EN61000-4-4 3 Surges EN61000-4-5 Installation class 4 A Conducted EN61000-4-6 3 A Magnetic Fields EN61000-4-8 3 A EN61000-4-11 (100 VAC) Dips and Interruptions EN61000-4-11 (240 VAC) Dip >95% (0 VAC), 8.3 ms A Dip 30% (70 VAC), 416 ms A Dip >95% (0 VAC), 4160 ms Dip >95% (0 VAC), 10.0 ms B A Dip 30% (168 VAC), 500 ms A Dip >95% (0 VAC), 5000 ms B www.xppower.com Notes & Conditions 4 LCE80 Series AC-DC Power Supplies Safety Approvals Safety Agency Safety Standard Notes & Conditions CB Report IEC60950-1-1, IEC62368-1 Information Technology UL UL60950-1, UL62368-1 Information Technology TUV EN62368-1 Information Technology CB Report IEC60335-1 Household Mechanical Details 4.00 (101.6) 0.13 (3.3) 3.75 (95.2) 2 1 Pin 1 CN1 AC-L Pin 3 AC-N 1.00 (25.0) 1.10 (27.9)max .0) 0.12 (3.0)max 2 (3 0.1 ø 4 1 2 3 4 5 6 0.13 (3.3) 2 1.74 (44.3) VR CN2 2.00 (50.8) CN1 CN2 Pin 1 +Vo Pin 2 +Vo Pin 3 +Vo Pin 4 -Vo Pin 5 -Vo Pin 6 -Vo Standard input and output connectors (CN1 & CN2) wafer with TAIWAN KING PIN TERMINAL PVHI series and mate with JST housing VHR series and JST SVH-21/41T-P1.1 series crimp terminal or equivalent. Mounting holes marked with must be connected to safety earth in Class I applications or connected together in Class II application. Notes 1. All dimensions shown in inches (mm). Tolerance: ±0.02 (0.5) 5 2. Weight: 0.32lbs (145g) approx. www.xppower.com 15 Aug 19