ISM43341-L77

ISM4334x Product Specification INVENTEK SYSTEMS ISM4334X-L77 Embedded SiP Module 802.11 a/b/g/n Bluetooth 4.0 & NFC Data Sheet DOC-DS-20072-3.2 Confidential Page 1 Inventek Systems ISM4334x Product Specification Table of Contents 1 PART NUMBER DETAIL DESCRIPTION .......................................................................... 3 1.1 Ordering Information ...................................................................................................... 3 2 OVERVIEW ........................................................................................................................... 3 3 FEATURES ............................................................................................................................ 4 3.1 Limitations ...................................................................................................................... 5 4 COMPLEMENTARY DOCUMENTATION ........................................................................ 5 4.1 Inventek Systems ............................................................................................................ 5 5 BLOCK DIAGRAM ............................................................................................................... 6 6 HOST INTERFACES ............................................................................................................. 6 6.1 UART Interface .............................................................................................................. 6 6.2 NFC Host Interfaces (ISM43341 only)........................................................................... 8 7 ELECTRICAL SPECIFICATIONS ....................................................................................... 8 7.1 Absolute Maximum Ratings ........................................................................................... 8 7.2 Environmental Ratings.................................................................................................... 9 7.3 Recommended Operating Conditions and DC Characteristics ....................................... 9 8 RF SPECIFICATIONS ........................................................................................................... 9 8.1 Bluetooth RF Specifications ........................................................................................... 9 8.2 WLAN RF Specifications ............................................................................................. 10 8.3 Environmental Specifications ....................................................................................... 13 9 PIN OUT AND DESCRIPTIONS ........................................................................................ 14 9.1 Module Pin-Out (1 of 2) ............................................................................................... 14 9.2 Module Pin-Out (2 of 2) ............................................................................................... 15 9.3 Recommended PCB Footprint (Bottom View) ............................................................. 16 9.4 Recommended PCB Footprint (Top View) .................................................................. 17 9.5 Detailed Pin Description ............................................................................................... 18 10 Product Compliance Considerations ..................................................................................... 20 11 Reflow Profile ....................................................................................................................... 21 12 Packaging Information .......................................................................................................... 22 12.1 MSL Level / Storage Condition .................................................................................... 22 12.2 Device baking requirements prior to assembly............................................................. 23 13 REVISION CONTROL ........................................................................................................ 23 14 CONTACT INFORMATION ............................................................................................... 23 DOC-DS-20072-3.2 Confidential Page 2 Inventek Systems ISM4334x Product Specification 1 PART NUMBER DETAIL DESCRIPTION 1.1 Ordering Information Device Description Ordering Number ISM43341-L77 2.4/5G Wi-Fi, Bluetooth, NFC SiP Module ISM43341-L77 ISM43340-L77 2.4/5G Wi-Fi, Bluetooth SiP Module ISM43340-L77 ISM43341-SDIOEVB or ISM43340 SDIO Evaluation Board ISM43341-SDIO-EVB 2 OVERVIEW The Inventek ISM4443X single-chip quad-radio device provides the highest level of integration for a wireless system, with integrated dual band (2.4 GHz/ 5 GHz) IEEE 802.11 a/b/g and single-stream IEEE 802.11n MAC/baseband/radio, Bluetooth 4.0. The ISM43341 also integrates a low power NFC controller. The ISM4443X includes integrated power amplifiers, LNAs and T/R switches for the 2.4 GHz and 5 GHz WLAN bands, greatly reducing the external part count, PCB footprint, and cost of the solution. It provides a small form-factor solution with minimal external components to drive down cost for mass volumes and allows for handheld device flexibility in size, form and function. Comprehensive power management circuitry and software ensure the system can meet the needs of high mobile devices that require minimal power consumption and reliable operations. The ISM4443X is compatible with the Bluetooth Low Energy operating mode, which provides a dramatic reduction in the power consumption of the Bluetooth radio and baseband. The primary application for this mode is to provide support for low data rate devices, such as sensors and remote controls. The ISM4443X implements the highly sophisticated Enhanced Collaborative Coexistence algorithms and hardware mechanisms, allowing for an extremely collaborative Bluetooth coexistence scheme along with coexistence support for external radios such as cellular and LTE, GPS, and Ultra-Wideband. For the WLAN section, host interface is a SDIO v2.0 interface. An independent, high-speed UART is provided for the Bluetooth host interface. Separate independent interfaces (I²C-compatible, SPI and UART) for NFC are also provided. DOC-DS-20072-3.2 Confidential Page 3 Inventek Systems ISM4334x Product Specification 3 FEATURES The ISM4443X supports the following WLAN, Bluetooth functions:                    Dual-band 2.4 GHz and 5 GHz IEEE 802.11 a/b/g/n Single-stream IEEE 802.11n support for 20 MHz and 40 MHz channels provides PHY layer rates up to 150 Mbps for typical upper-layer throughput in excess of 90 Mbps. Supports a single 2.4 GHz antenna shared between WLAN and Bluetooth IEEE 802.11a/b/g/n dual-band radio with internal Power Amplifiers, LNAs and T/R switches OneDriver™ software architecture for easy migration from existing embedded WLAN and Bluetooth devices as well as future devices. Bluetooth v4.0 with integrated Class 1 PA Concurrent Bluetooth, NFC and WLAN operation On-chip WLAN driver execution capable of supporting IEEE 802.11 functionality Single and dual-antenna support WLAN host interface : o SDIO v2.0, including default and high-speed timing. BT host digital interface (can be used concurrently with above interface): o UART (up to 4 Mbps) ECI – enhanced coexistence support, ability to coordinate BT SCO transmissions around WLAN receives I²S/PCM for BT audio HCI high-speed UART (H4, H4 +, H5) transport support Bluetooth SmartAudio® technology improves voice and music quality to headsets Bluetooth low power inquiry and page scan Bluetooth Low Energy (BLE) support Bluetooth Packet Loss Concealment (PLC) Bluetooth Wide Band Speech (WBS) The BBC supports all Bluetooth 4.0 features, with the following benefits:  Dual-mode classic Bluetooth and classic Low Energy (BT and BLE) operation.  Low Energy Physical Layer  Low Energy Link Layer  Enhancements to HCI for Low Energy  Low Energy Direct Test mode  AES encryption The ISM43341 supports the following NFC features:    Support for the ISO/IEC 18092, ISO/IEC 21481, ISO/IEC 14443 Types A, B and B’, Japanese Industrial Standard (JIS) (X) 6319-4 and ISO/IEC 15693 standards No active components required for antenna or field-power conditioning Individual byte framing DOC-DS-20072-3.2 Confidential Page 4 Inventek Systems ISM4334x Product Specification           Hardware-based collision detection and modulation controls Reader/Writer (R/W) mode Active and Passive Peer-to-Peer (P2P) mode Tag/Card Emulation mode: o Support for battery-enabled card emulation mode o Support for two levels of “residual” battery-assisted card emulation mode o Support for “battery-off” card emulation mode (completely powered from the field) Dual Signal Wire Protocol (SWP) interfaces: o SWP_0 with platform power management unit (PMU) power switching to a UICC SIM card o SWP_1 for embedded secure element or a second UICC SIM card Supports Application ID (AID) routing between a reader and secure element(s) Ability to recover card emulation personality data Internal low-power oscillator for periodic wake-up and mode switch operation Low-Power Target Detection mode for extremely low average current consumption (“sniff mode”) NFC Forum NFC Controller Interface (NCI) for the host interface 3.1 Limitations Inventek Systems products are not authorized for use in safety-critical applications (such as life support) where a failure of the Inventek Systems product would reasonably be expected to cause severe personal injury or death. 4 COMPLEMENTARY DOCUMENTATION 4.1 Inventek Systems  Evaluation Board o SDIO Evaluation Board Specification o EVB User’s Guide o Drivers under NDA o Design Guidelines DOC-DS-20072-3.2 Confidential Page 5 Inventek Systems ISM4334x Product Specification 5 BLOCK DIAGRAM Figure 1 Inventek’s ISM4443X General Block Diagram (NFC on ISM43341 version only) 6 HOST INTERFACES 6.1 UART Interface The ISM4443X shares a single UART for Bluetooth. The UART is a standard 4-wire interface (RX, TX, RTS and CTS) with adjustable baud rates from 9600 bps to 4.0 Mbps. The interface features an automatic baud rate detection capability that returns a baud rate selection. Alternatively, the baud rate may be selected through a vendorspecific UART HCI command. The UART has a 1040-byte receive FIFO and a 1040-byte transmit FIFO to support EDR. Access to the FIFO is conducted through the AHB interface through either DMA or the CPU. The UART supports the Bluetooth 4.0 UART HCI specification: H4, a custom Extended H4 and H5. The default baud rate is 115.2 Kbaud. The UART supports the 3-wire H5 UART transport, as described in the Bluetooth specification (“Three-wire UART Transport Layer”). Compared to H4, the H5 UART transport reduces the number of signal lines required by eliminating the CTS and RTS signals. The ISM4443X UART can perform XON/XOFF flow control and includes hardware support for the Serial Line input Protocol (SLIP). It can also perform wake-on activity. For example, activity on the RX or CTS inputs can wake the chip from a sleet state. DOC-DS-20072-3.2 Confidential Page 6 Inventek Systems ISM4334x Product Specification Normally, the UART baud rate is set by a configuration record downloaded after device reset, or by automatic baud rate detection, and the host does not need to adjust the baud rate. Support for changing the baud rate during normal HCI UART operation is included through a vendor-specific command that allows the host to adjust the contents of the baud rate registers. The ISM4443X UARTs operate correctly with the host UART as long as the combined baud rate error of the two devices is within ±2% (see Table 12). Desired Rate 4000000 3692000 3000000 2000000 1500000 1444444 921600 460800 230400 115200 57600 38400 28800 19200 14400 9600 Actual Rate 4000000 3692308 3000000 2000000 1500000 1454544 923077 461538 230796 115385 57692 38400 28846 19200 14423 9600 Error (%) 0.00 0.01 0.00 0.00 0.00 0.70 0.16 0.16 0.17 0.16 0.16 0.00 0.16 0.00 0.16 0.00 Table 1: Example of Common Baud Rates DOC-DS-20072-3.2 Confidential Page 7 Inventek Systems ISM4334x Product Specification 6.2 NFC Host Interfaces (ISM43341 only) The ISM43341 supports UART, I²C-compatible BSC, and SPI for the host interface physical transport layer. The host interface type is selected upon power-up boot, depending upon the state of the NFC_SPI_INT pin.  NFC_SPI_INT pulled low – The UART interface will be selected  NFC_SPI_INT pulled high – The I²C-compatible BSC slave interface will be selected  NFC_SPI_INT floating – The SPI interface will be selected. After boot, the NFC_SPI_INT signal will function as the SPI interrupt output. During powerup book, the external host must leave this pin floating, as in the case of the tri-state or input pin. The external host must also ignore interrupts from this signal for a period of 10 milliseconds after boot-up. The NFC host interface pins are multiplexed onto shared signals as defined in Table 2. UART NFC_CTS NFC_RTS BSC I2C_REQ I2C_SCL SPI SPI_CS SPI_MISO NFC_URX NFC_UTX Pull low I2C_SDA Pull high SPI_CLK SPI-MOSI NFC_SPI_INT Table 2: NFC Host Interface Multiplexing 7 ELECTRICAL SPECIFICATIONS 7.1 Absolute Maximum Ratings Caution! The absolute maximum ratings in Table 28 indicate levels where permanent damage to the device can occur, even if these limits are exceeded for only a brief duration. Functional operation is not guaranteed under these conditions. Operation at absolute maximum conditions for extended periods can adversely affect long-term reliability of the device. Rating DC supply for VBAT and PA driver supply DC supply voltage for digital I/O Symbol VBAT VIO Value -0.5 to +6.0 -0.5 to 3.9 Table 3: Absolute Maximum Ratings DOC-DS-20072-3.2 Confidential Page 8 Inventek Systems Unit V V ISM4334x Product Specification 7.2 Environmental Ratings Characteristic Ambient Temperature (Ta) Storage Temperature Value -30 to +85 -40 to +125 Relative Humidity Less than 60 Less than 85 Units °C °C % % Conditions/Comments * Functional operation Storage Operation Table 4: Environmental Ratings 7.3 Recommended Operating Conditions and DC Characteristics Caution! Functional operation is not guaranteed outside of the limits shown in Table 31 and operation outside these limits for extended periods can adversely affect long-term reliability of this devices. Parameter Symbol Min Typical Max Unit DC supply Voltage for VBAT VBAT 3.0 3.3 4.8 V DC supply voltage for digital I/O VIO 1.8 3.3 3.6 V Table 5: Recommended Operating Conditions and DC Characteristics a. The ISM43341 is functional across this range of voltages. Optimal RF performance specified in the data sheet, however, is guaranteed only for 3.0V >VBAT >4.8V. b. The maximum continuous voltage is 4.8V. Voltages up to 5.5V for up to 10 seconds, cumulative duration, over the lifetime of the device are allowed. Voltages as high as 5.0V for up to 250 seconds, cumulative duration, over the lifetime of the device are allowed. c. Programmable 2 mA to 16 mA drive strength. Default is 10 mA 8 RF SPECIFICATIONS 8.1 Bluetooth RF Specifications Note: Values in this datasheet are design goals and are subject to change based on the result of device characterization. DOC-DS-20072-3.2 Confidential Page 9 Inventek Systems ISM4334x Product Specification Unless otherwise stated, limit values apply for the conditions specified in Tabel 29: “Environmental Ratings” on page 117 and table 31: “Recommended Operating Conditions and DC Characteristics” on page 118. Typical values apply for the following conditions:  VBAT = 3.6V  Ambient temperature +25°ͨC Parameter Conditions Min Typical Max Unit Note: The specifications in this table are measured at the Chip port output unless otherwise specified: General Frequency Range GFSK, 0.1% BER, 1 Mbps π/4-DQPSK, 0.01% BER, 2 Mbps 8-DPSK, 0.01% BER, 3 Mbps - RX sensitivity Input IP3 Maximum input at antenna 2402 - 2480 MHz - -93.5 - dBm - -95.5 - dBm - -89.5 - dBm -16 - - -20 dBm dBm Min Typical Max Unit 2402 - 2480 MHz 10.0 12.0 - dBm 7.0 7.0 2 9.0 9.0 4 6 dBm dBm dB Table 6: Bluetooth Receiver RF Specifications Parameter Conditions General Frequency Range Basic rate (GFSK) Tx power at Bluetooth QPSK Tx Power at Bluetooth 8PSK Tx Power at Bluetooth Power control step - Table 7: Bluetooth Transmitter RF Specifications 8.2 WLAN RF Specifications DOC-DS-20072-3.2 Confidential Page 10 Inventek Systems ISM4334x Product Specification The ISM4443X includes an integrated dual-band direct conversion radio that supports either the 2.4 GHz band or the 5 GHz band. The ISM4443X does not provide simultaneous 2.4 GHz and 5 GHz operation. This section describes the RF characteristics of the 2.4 GHz and 5 GHz portions of the radio. Note: Values in the data sheet are design goals and are subject to change based on the results of device characterization. Unless otherwise stated, limit values apply for the condition specified in Table 29: “Environmental Ratings” on page 117 and Table 31: “Recommended Operating Conditions and DC Characteristics” on page 118. Typical values apply for the following conditions:  VBAT = 3.6V  Ambient temperature +25°C 2.4 GHz Band General RF Specifications Item Conditions Min Typical Max Unit Tx/Rx switch time Rx/Tx switch time Power-up and powerdown ramp time Including TX ramp down Including TX ramp up - - 5 2 μs μs DSSS/CCK Modulations - -