8
TM
3M
7
6
5
4
3
2
1
NOTES
4-WALL, TRIPOLARIZED HEADER, 810 SERIES
1. REGULATORY INFORMATION:
VISIT 3M.com/regs
* TRIPOLARIZED FOR ROBUST ALIGNMENT WHEN MATING TO
3MTM 820 SERIES SOCKET.
* .050" X .100" HALVES THE CONNECTOR LENGTH VS.
TRADITIONAL .100" X .100" PRODUCTS.
* LATCHING EJECTOR FOR RUGGED HIGH PERFORMANCE APPLICATIONS.
* AVAILABLE FOR THROUGH HOLE OR SURFACEMOUNT ATTACHMENT.
* HIGH TEMPERATURE PLASTIC FOR LEAD FREE SURFACEMOUNT OR
PASTE-IN-HOLE SOLDERING METHODS.
* FOUR-WALL SHROUD PROVIDES CONTACT PROTECTION.
.050" X .100" LATCH/EJECTOR, PTH AND SMT STRAIGHT, PTH RIGHT ANGLE
2
UNLESS OTHERWISE NOTED, REFERENCES
TO INDUSTRY SPECIFICATIONS ARE
INTENDED TO INDICATE SUBSTANTIAL
COMPLIANCE TO THE MATERIAL ELEMENTS
OF THE SPECIFICATION. SUCH
REFERENCES SHOULD NOT BE CONSTRUED
AS A GUARANTEE OF COMPLIANCE TO ALL
REQUIREMENTS IN A GIVEN SPECIFICATION.
3
THIS POLARIZING SLOT DOES NOT
EXIST ON THE 20 POSITION HEADER.
D
D
4. RECOMMENDED TO BE MATED TO THE
.050" X .100" 3MTM 820XX SERIES
SOCKETS, TS-0254.
2
PHYSICAL:
INSULATION:
MATERIAL:
FLAMMABILITY:
COLOR:
CONTACT:
MATERIAL:
PLATING:
UNDER PLATING:
WIPING AREA:
SOLDER TAILS:
MARKINGS:
RIGHT ANGLE
VERSION
81XXX-5X0X03
C
2
5
SOLDER THIEF SOLDER PADS REQUIRED
ONLY ON SOLDER SIDE OF PC BOARD.
6
A DUMMY OR SOLDER THIEF SOLDER PAD
AT THE END OF EACH ROW IS RECOMMENDED
ON THE BOTTOM OR SOLDER SIDE OF THE
PC BOARD IN ORDER TO HELP PREVENT
SOLDER BRIDGING ON THE END SOLDER
TAILS. THE SOLDER THIEFS ARE ONLY
REQUIRED ON THE END OF THE ROWS WHICH
THE SOLDER BATH LAST.
7
RECOMMENDED TO PROCESS PC BOARDS
THROUGH THE SOLDER BATH SUCH THAT
THE CONNECTOR ENTERS END FIRST
(TWO SOLDER TAILS AT A TIME).
THIS WILL PREVENT SOLDER BRIDGING.
8
IN ORDER TO FACILITATE SOLDERING
IT IS RECOMMENDED THAT EJECTOR
LATCHES BE INSTALLED AFTER THE
SOLDERING PROCESS.
HIGH TEMRERATURE PLASTIC (LCP)
UL94V-0
BLACK
COPPER ALLOY
50 "-150 " [1.27 m-3.81 m] NICKEL-OVERALL
30 " [0.76 m] GOLD AVG.
100 "-300 " [2.54 m-7.62 m] MATTE TIN
3M LOGO, PART No. AND ORIENTATION TRIANGLE
ELECTRICAL:
CURRENT RATING: 3.00 A, 1 CONTACT POWERED
2.00 A, 4 CONTACTS POWERED
0.75 A, ALL CONTACTS POWERED
C
RATING CONDITIONS: EIA-364-070 METHOD 2, 30 C MAXIMUM
TEMPERATURE RISE, 20% DERATED. REFERENCE APPROPRIATE
3M PRODUCT SPECIFICATION FOR DETAILED CURRENT DERATING CURVES.
L
ENVIRONMENTAL:
78-5100-0253-4
2
REVISION
INSULATION RESISTANCE: >1 X 109 AT 500 VDC
WITHSTANDING VOLTAGE: 500VRMS AT SEA LEVEL
DRAWING NUMBER
TEMPERATURE RATING: -55 C TO +105 C
PROCESS RATING: MAXIMUM 260 C
MOISTURE SENSITIVITY LEVEL: 1 (PER J-STD-020C)
STRAIGHT
VERSION
81XXX-6X0X0X
B
DIMENSIONS: INCHES [MM]
[MM] IS REF. ONLY
DESIGN REFERENCE
NEXT ASSEMBLY
ACCESS
CODES
SURFACEMOUNT
VERSION
81XXX-6X0C0X
A
DIVISION
DO NOT
SCALE
DRAWING
THIRD ANGLE PROJECTION
INCHES
.0
.1
.00
.01
.000
.005
.0000
.0002
MAX SURFACE ROUGHNESS
UL FILE NO: E68080
6
5
4
3
ALL SURFACES
MARKED ONLY
2
MILLIMETERS
0
.0
.00
.000
ANGLES
JNC SAN
REVISED AND REDRAWN
REV
ECO
ISSUE DATE AND DESCRIPTION
DRFT
DATE
CASTIGLIONE
JAN 13,2022
CHKD
DATE
C
3M Center
St. Paul,
TOLERANCES
EXCEPT AS
NOTED
SCALE
R
3M IS A TRADEMARK OF 3M COMPANY.
FOR TECHNICAL, SALES OR ORDERING
INFORMATION CALL 800-225-5373
JAN 13,2022
DIVISION CODE
INTERPRET PER
ASME Y14.5 - 2018
7
101674
EMSD
3M ELECTRONICS MATERIALS SOLUTIONS DIVISION
INTERCONNECT SOLUTIONS
http://www.3M.com/interconnect
8
L
MN
55144
DRFT
CHKD
MFG
DATE
APPVL
DATE
S. NEU
JAN 13,2022
3M COPYRIGHT 2022
This document and the information it contains are
3M property and may not be reproduced or further
distributed without 3M permission, or used or
disclosed other than for 3M authorized purposes.
All rights reserved.
TITLE
TRIPOLARIZED HEADER,
4-WALL, LATCH/EJECT,
.050" X .100"
CAGE SIZE
NUMBER
MODEL
810
DRAWING NO.
REV.
78-5100-0253-4
DET.
LISTS
1
YES
NO
L
SHT 1 OF 5
Imaged: Central Standard Time 1/25/2022 -- UTC Offset (hrs) 6
B
A
8
7
6
5
4
3
2
1
3MTM 4-WALL, TRIPOLARIZED HEADER, 810 SERIES
.024
.050" X .100" LATCH/EJECTOR, PTH AND SMT STRAIGHT, PTH RIGHT ANGLE
0.61
.100
TABLE 1
D
TABLE 2
CONTACT
DIM. "D"
DIM. "A" DIM. "B" DIM. "C"
QTY.
SHORT
1.060
.722
.500
1.671
020
[26.92]
[18.34]
[12.70]
[42.44]
1.210
.872
.650
1.821
026
[30.73]
[22.15]
[16.51]
[46.25]
1.460
1.122
.900
2.071
036
[37.80]
[28.50]
[22.86]
[52.60]
1.560
1.222
1.000
2.171
040
[39.62]
[31.04]
[25.40]
[55.14]
1.810
1.472
1.250
2.421
050
[45.97]
[37.39]
[31.75]
[61.49]
2.060
1.722
1.500
2.671
060
[52.32]
[43.74]
[38.10]
[67.84]
2.260
1.922
1.700
2.871
068
[57.40]
[48.82]
[43.18]
[72.92]
2.560
2.222
2.000
3.171
080
[65.02]
[56.44]
[50.80]
[80.54]
3.060
2.722
2.500
3.671
100
[77.72]
[69.14]
[63.50]
[93.24]
DIM. "D"
LONG
1.842
[46.79]
1.992
[50.60]
2.242
[56.95]
2.342
[59.49]
2.592
[65.84]
2.842
[72.19]
3.042
[77.27]
3.342
[84.89]
3.842
[97.59]
PCB
THICKNESS
.062 [1.57]
.094 [2.39]
.125 [3.18]
DIM. "E"
MIN.
SEE TABLE 3
0.08
AFTER PLATING
TYP.
.002
2.54
.003
DIM. "C"
.025
0.05
.002
0.64
DIM. "F"
.002
FLOW SOLDER
0.05
EDGE OF
PC BOARD
DIRECTION
.090 [2.29]
.112 [2.84]
.143 [3.63]
.045
.060
.025 0.64
.035 0.89
D
1.14
1.52
A
Detail
SCALE 8x
TYPICAL
TABLE 3
ADJACENT CONNECTOR
EJECTOR
DIM. "E"
LATCHES
NONE
.575 [14.61]
LONG
1.010 [25.65]
SHORT
.885 [22.48]
POSITION #2
.355 [9.02] MAX.
.305 [7.75] MIN.
5
2X
.109
.002
2.77
.160
0.05
.002
4.06
A
POSITION #1
.050
.002
1.27
0.05
TYP.
0.05
SOLDER THIEF SOLDER PADS
SEE NOTE 6
TOLERANCE
NON-ACCUMULATIVE
RECOMMENDED MOUNTING HOLE PATTERN
7
PTH RIGHT ANGLE HEADER
(SHOWN FOR MOUNTING SIDE OF PC BOARD)
C
C
DIM. "A"
ORDERING INFORMATION
DIM. "B"
PTH RIGHT ANGLE HEADER
DIM. "C"
81XXX-5X0X03-RB
.092
CONTACT QTY:
(SEE TABLE 1)
2.34
CONTACT
2 = FOR
3 = FOR
4 = FOR
7.87
SOLDER TAIL:
.062 [1.75] PC BOARD (STANDARD)
.094 [2.39] PC BOARD (SPECIAL ORDER)
.125 [3.18] PC BORAD (SPECIAL ORDER)
DRAWING NUMBER
EJECTOR/LATCH SYSTEM:
0 = NONE (SPECIAL ORDER)
5 = WITH SHORT EJECTORS INSTALLED (SPECIAL ORDER)
6 = WITH LONG EJECTORS INSTALLED (STANDARD)
.310
L
2X
REVISION
3
78-5100-0253-4
POS #2
.100
.015 0.38 SQ.
POS #1
B
.050
TYP.
2.54
EJECTOR LATCHES
1.27
B
(IF ORDERED SEPARATELY)
TYP.
LONG LATCHES: 3505-28
SHORT LATCHES: 3505-29
.168
4.26
.010
0.25
.412
10.47
.010
.828
0.25
2X
.116 2.95
21.03
.105
.265
.610
.405
15.49
4.06
10.29
L
3.56
8
.160
6.73
.140
A
2.67
SHORT
LATCH
LONG
LATCH
.310
0.25
DESIGN REFERENCE
NEXT ASSEMBLY
ACCESS
CODES
7.87
8
DIVISION
DO NOT
SCALE
DRAWING
1.27
.015
.100
2.54
.015 0.38 SQ.
THIRD ANGLE PROJECTION
INTERPRET PER
ASME Y14.5 - 2018
TYP.
MAX SURFACE ROUGHNESS
MARKED ONLY
6
5
JNC SAN
4
3
ISSUE DATE AND DESCRIPTION
DATE
CASTIGLIONE
JAN 13,2022
CHKD
DATE
C
3M Center
St. Paul,
TOLERANCES
EXCEPT AS
NOTED
SCALE
ALL SURFACES
7
ECO
DRFT
DIVISION CODE
0.38
DIM. "F" .010
SEE TABLE 2
8
REV
EMSD
CONTACT
MATING
POINT
JAN 13,2022
REVISED AND REDRAWN
.010
.050
POSITION #1
INDICATOR
101674
2
INCHES
.0
.1
.00
.01
.000
.005
.0000
.0002
MILLIMETERS
0
.0
.00
.000
ANGLES
MN
55144
DRFT
CHKD
MFG
DATE
APPVL
DATE
S. NEU
JAN 13,2022
3M COPYRIGHT 2022
This document and the information it contains are
3M property and may not be reproduced or further
distributed without 3M permission, or used or
disclosed other than for 3M authorized purposes.
All rights reserved.
TITLE
TRIPOLARIZED HEADER,
4-WALL, LATCH/EJECT,
.050" X .100"
CAGE SIZE
NUMBER
MODEL
810
DRAWING NO.
REV.
78-5100-0253-4
DET.
LISTS
1
YES
NO
L
SHT 2 OF 5
Imaged: Central Standard Time 1/25/2022 -- UTC Offset (hrs) 6
DIM. "D" REF.
A
8
7
6
5
4
3
2
1
3MTM 4-WALL, TRIPOLARIZED HEADER, 810 SERIES
.025
.050" X .100" LATCH/EJECTOR, PTH AND SMT STRAIGHT, PTH RIGHT ANGLE
0.63
DIM. "E"
MIN.
SEE TABLE 6
.003
0.08
DIM. "D"
AFTER PLATING
D
TABLE 4
CONTACT
DIM. "C"
DIM. "A" DIM. "B"
QTY.
SHORT
1.060
.722
1.671
020
[26.92]
[18.34]
[42.44]
1.210
.872
1.821
026
[30.73]
[22.15]
[46.25]
1.460
1.122
2.071
036
[37.80]
[28.50]
[52.60]
1.560
1.222
2.171
040
[39.62]
[31.04]
[55.14]
1.810
1.472
2.421
050
[45.97]
[37.39]
[61.49]
2.060
1.722
2.671
060
[52.32]
[43.74]
[67.84]
2.260
1.922
2.871
068
[57.40]
[48.82]
[72.92]
2.560
2.222
3.171
080
[65.02]
[56.44]
[80.54]
3.060
2.722
3.671
100
[77.72]
[69.14]
[93.24]
5.21
TABLE 5
DIM. "C"
LONG
1.842
[46.79]
1.992
[50.60]
2.242
[56.95]
2.342
[59.49]
2.592
[65.84]
2.842
[72.19]
3.042
[77.27]
3.342
[84.89]
3.842
[97.59]
DIM. "D"
.860
[21.84]
1.010
[25.65]
1.260
[32.00]
1.360
[34.54]
1.610
[40.89]
1.860
[47.24]
2.060
[52.32]
2.360
[59.94]
2.860
[72.64]
PCB
THICKNESS
.062 [1.57]
.094 [2.39]
2X .205
.100
DIM. "F"
2.54
.002
FLOW SOLDER
.003
DIRECTION
0.08
.002
B
POSITION #2
0.05
.092 [2.34]
.110 [2.79]
EDGE OF
PC BOARD
.050
.045
.060
.025 0.64
.035 0.89
TABLE 6
ADJACENT CONNECTOR
EJECTOR
DIM. "E"
LATCHES
NONE
.215 [5.46]
LONG
.650 [16.51]
SHORT
.525 [13.34]
D
.003
1.27
0.08
1.14
1.52
B
Detail
SCALE 8x
TYPICAL
.225
MIN.
5.72
5
.160
4.06
2X
POSITION #1
MIN.
.109
.002
2.77
.050
0.05
SOLDER THIEF SOLDER PADS
SEE NOTE 6
TYP.
1.27
TOLERANCE
NON-ACCUMULATIVE
RECOMMENDED MOUNTING HOLE PATTERN
7
PTH VERTICAL HEADER
(SHOWN FOR MOUNTING SIDE OF PC BOARD)
C
C
DIM. "A"
ORDERING INFORMATION
DIM. "B"
PTH STRAIGHT HEADER
3
EJECTOR/LATCH SYSTEM:
0 = NONE (SPECIAL ORDER)
5 = WITH SHORT EJECTORS INSTALLED (SPECIAL ORDER)
6 = WITH LONG EJECTORS INSTALLED (STANDARD)
7.87
.100
POSITION #1
CONTACT
2 = FOR
3 = FOR
4 = FOR
2.54
SOLDER TAIL:
.062 [1.75] PC BOARD (STANDARD)
.094 [2.39] PC BOARD (SPECIAL ORDER)
.125 [3.18] PC BORAD (SPECIAL ORDER)
TYP.
EJECTOR LATCHES
B
LONG
LATCH
DIM. "C"
SHORT
LATCH
.168
4.26
B
(IF ORDERED SEPARATELY)
LONG LATCHES: 3505-28
SHORT LATCHES: 3505-29
.010
0.25
.412
10.47
.010
.828
0.25
21.03
.140
3.56
.610
.010
0.25
.265
.405
15.49
6.73
10.29
DIM. "F" .010
SEE TABLE 5
.050
L
101674
JAN 13,2022
JNC SAN
REVISED AND REDRAWN
2X
A
.015
2.34
SQ.
0.38
2X
1.27
.015
.092
.116
CONTACT
MATING
POINT
OPTIONAL
MTG POST
TYP.
NEXT ASSEMBLY
ACCESS
CODES
0.38
POSITION #1
INDICATOR
DESIGN REFERENCE
.100
DIVISION
DO NOT
SCALE
DRAWING
INTERPRET PER
ASME Y14.5 - 2018
MAX SURFACE ROUGHNESS
ALL SURFACES
MARKED ONLY
5
4
CASTIGLIONE
JAN 13,2022
CHKD
DATE
C
3
3M Center
St. Paul,
TOLERANCES
EXCEPT AS
NOTED
SCALE
THIRD ANGLE PROJECTION
6
ISSUE DATE AND DESCRIPTION
DATE
EMSD
2.54
DIM. "D"
7
ECO
DRFT
DIVISION CODE
2.95
8
REV
2
INCHES
.0
.1
.00
.01
.000
.005
.0000
.0002
MILLIMETERS
0
.0
.00
.000
ANGLES
MN
55144
DRFT
CHKD
MFG
DATE
APPVL
DATE
S. NEU
JAN 13,2022
3M COPYRIGHT 2022
This document and the information it contains are
3M property and may not be reproduced or further
distributed without 3M permission, or used or
disclosed other than for 3M authorized purposes.
All rights reserved.
TITLE
TRIPOLARIZED HEADER,
4-WALL, LATCH/EJECT,
.050" X .100"
CAGE SIZE
NUMBER
MODEL
810
DRAWING NO.
REV.
78-5100-0253-4
DET.
LISTS
1
YES
NO
L
SHT 3 OF 5
Imaged: Central Standard Time 1/25/2022 -- UTC Offset (hrs) 6
.050 1.27
BOARD MOUNTING OPTIONS:
1 = NONE (SPECIAL ORDER)
3 = PRESS FIT POSTS BOTH ENDS (STANDARD)
DRAWING NUMBER
.310
L
CONTACT QTY:
(SEE TABLE 4)
REVISION
81XXX-6X0X0X-RB
78-5100-0253-4
POSITION #2
A
8
7
6
5
4
3MTM 4-WALL, TRIPOLARIZED HEADER, 810 SERIES
.065
.050" X .100" LATCH/EJECTOR, PTH AND SMT STRAIGHT, PTH RIGHT ANGLE
3
2
.002
1.65
.109
0.05
D
1.060
[26.92]
1.210
[30.73]
1.460
[37.80]
1.560
[39.62]
1.810
[45.97]
2.060
[52.32]
2.260
[57.40]
2.560
[65.02]
3.060
[77.72]
020
026
036
040
050
060
068
080
100
.722
[18.34]
.872
[22.15]
1.122
[28.50]
1.222
[31.04]
1.472
[37.39]
1.722
[43.74]
1.922
[48.82]
2.222
[56.44]
2.722
[69.14]
1.671
[42.44]
1.821
[46.25]
2.071
[52.60]
2.171
[55.14]
2.421
[61.49]
2.671
[67.84]
2.871
[72.92]
3.171
[80.54]
3.671
[93.24]
DIM. "D"
LONG
DIM. "F"
1.842
[46.79]
1.992
[50.60]
2.242
[56.95]
2.342
[59.49]
2.592
[65.84]
2.842
[72.19]
3.042
[77.27]
3.342
[84.89]
3.842
[97.59]
DIM. "G"
.450
[11.43]
.600
[15.24]
.850
[21.59]
.950
[24.13]
1.200
[30.48]
1.450
[36.83]
1.650
[41.91]
1.950
[49.53]
2.450
[62.23]
N/A
TAPE AND
REEL
SUFFIX
.042
1.07
WF
.025
[0.64]
WF
N/A
WG
N/A
WG
.025
[0.64]
WG
0.000
WG
0.000
WH
0.000
WH
0.000
.003
DIM. "H" MIN.
SEE TABLE 8
0.08
DIM. "F"
D
AFTER PLATING
C
POSITION #2
Detail
SCALE 8x
TYPICAL
.029
.001
0.74
2X .075
C
0.03
DIM. "G"
.002
1.90
0.05
OPTIONAL PLATED THRU
HOLE FOR METAL CLIP
.218
5.54
TABLE 8
ADJACENT CONNECTOR
EJECTOR
DIM. "H"
LATCHES
NONE
.775 [19.69]
LONG
1.085 [27.56]
SHORT
1.21 [30.73]
WH
.003
.376
0.08
.109
9.55
.002
2.77
.050
0.05
POSITION #1
.158
.002
4.01
C
0.05
OPTIONAL DRILLED
HOLE FOR PLASTIC
MTG POST
TABLE 7
CONTACT
DIM. "D"
DIM. "A" DIM. "B"
QTY.
SHORT
.002
2.77
FULL RADIUS
1
0.05
.205
5.21
1.27
.003
TYP.
0.05
TOLERANCE
NON-ACCUMULATIVE
0.08
NOTE:
1. LATCHES SUPPLIED IN THE "OPEN" POSITION UNLESS SPECIFIED OTHERWISE
2. SUFFIX DETERMINED WITH NO POSTS OR CLIPS.
3. ADDITION OF POSTS OR CLIPS MAY INCREASE SUFFIX.
4. 120MM (WH)IS THE MAXIMUM WIDTH OF POCKET TAPE.
.002
RECOMMENDED MOUNTING PAD PATTERN
7
SURFACE MOUNT HEADER
(SHOWN FOR MOUNTING SIDE OF PC BOARD)
C
DIM. "A"
ORDERING INFORMATION
DIM. "B"
POSITION #2
SURFACE MOUNT STRAIGHT HEADER
3
L
CONTACT QTY:
(SEE TABLE 7)
EJECTOR/LATCH SYSTEM:
0 = NONE (SPECIAL ORDER)
5 = WITH SHORT EJECTORS INSTALLED (SPECIAL ORDER)
6 = WITH LONG EJECTORS INSTALLED (STANDARD)
.100
.050
VACUUM
CLIP
POSITION #1
.015
SQ.
BOARD MOUNTING OPTIONS:
1 = NONE
4 = PRESS FIT POST AT POSITION 1 END
7 = METAL RETENTION CLIPS
8 = POS #1 END POST AND METAL RETENTION CLIPS
(SPECIAL ORDER)
2.54
1.27
0.38
TYP.
DRAWING NUMBER
7.87
PACKAGING OPTIONS:
BLANK = TRAYS
WX = TAPE AND REEL PACKAGE
SEE TABLE 7
78-5100-0253-4
.310
REVISION
81XXX-6X0C0X-RB-XX
TYP.
B
B
EJECTOR LATCHES
DIM. "D"
SHORT
LATCH
.168
4.26
LONG LATCHES: 3505-28
SHORT LATCHES: 3505-29
LONG
LATCH
.010
.412
0.25
.010
10.47
.828
0.25
21.03
.140
.610
3.56
.010
0.25
.265
.405
15.49
6.73
L
10.29
101674
JAN 13,2022
JNC SAN
REVISED AND REDRAWN
DESIGN REFERENCE
.050
A
.015 0.38
.092
2.34
DIVISION
1.27
.116
2.95
2.36
POSITION #1
INDICATOR
OPTIONAL
SINGLE MTG
POST
CONTACT
MATING
POINT
.093
8.79
.010
DO NOT
SCALE
DRAWING
0.25
THIRD ANGLE PROJECTION
ALL SURFACES
MARKED ONLY
6
5
4
3
ISSUE DATE AND DESCRIPTION
DATE
CASTIGLIONE
JAN 13,2022
CHKD
DATE
C
3M Center
St. Paul,
TOLERANCES
EXCEPT AS
NOTED
SCALE
INTERPRET PER
ASME Y14.5 - 2018
7
ECO
DRFT
DIVISION CODE
MAX SURFACE ROUGHNESS
8
REV
EMSD
.346
OPTIONAL METAL
RETENTION CLIPS
NEXT ASSEMBLY
ACCESS
CODES
2
INCHES
.0
.1
.00
.01
.000
.005
.0000
.0002
MILLIMETERS
0
.0
.00
.000
ANGLES
MN
55144
DRFT
CHKD
MFG
DATE
APPVL
DATE
S. NEU
JAN 13,2022
3M COPYRIGHT 2022
This document and the information it contains are
3M property and may not be reproduced or further
distributed without 3M permission, or used or
disclosed other than for 3M authorized purposes.
All rights reserved.
TITLE
TRIPOLARIZED HEADER,
4-WALL, LATCH/EJECT,
.050" X .100"
CAGE SIZE
NUMBER
MODEL
810
DRAWING NO.
REV.
78-5100-0253-4
DET.
LISTS
1
YES
NO
L
SHT 4 OF 5
Imaged: Central Standard Time 1/25/2022 -- UTC Offset (hrs) 6
(IF ORDERED SEPARATELY)
A
8
7
6
5
4
3
2
1
3MTM 4-WALL, TRIPOLARIZED HEADER, 810 SERIES
.050" X .100" LATCH/EJECTOR, PTH AND SMT STRAIGHT, PTH RIGHT ANGLE
D
D
Regulatory: For regulatory information about this product, visit 3M.com/regs
or contact your 3M representative.
Technical Information: The technical information, recommendations and other
statements contained in this document are based upon tests or experience that
3M believes are reliable, but the accuracy or completeness of such information
is not guaranteed.
Product Use: Many factors beyond 3M's control and uniquely within user's control
can affect the use and performance of a 3M product in a particular application.
Given the variety of factors that can affect the use and performance of a
3M product, user is solely responsible for evaluating the 3M product and
determining whether it is fit for a particular purpose and suitable for user's
method of application.
C
78-5100-0253-4
L
REVISION
Warranty, Limited Remedy, and Disclaimer: Unless an additional warranty is
specifically stated on the applicable 3M product packaging or product literature,
3M warrants that each 3M product meets the applicable 3M product specification at
the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS,
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR
CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED
WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OR TRADE.
If the 3M product does not conform to this warranty, then the sole and exclusive
remedy is, at 3M's option, replacement of the 3M product or refund of the purchase
price.
DRAWING NUMBER
Limitation of Liability: Except where prohibited by law, 3M will not be liable for
any loss or damage arising from the 3M product, whether direct, indirect, special,
incidental or consequential, regardless of the legal theory asserted, including
warranty, contract, negligence or strict liability.
3M Company
Electronics Materials Solutions Division
13011 McCallen Pass, Bldg. C
Austin, TX 78753-5380
1-800-225-5373
www.3M.com/interconnect
B
B
L
101674
JAN 13,2022
JNC SAN
REVISED AND REDRAWN
DESIGN REFERENCE
NEXT ASSEMBLY
ACCESS
CODES
A
DIVISION
REV
ECO
DATE
CASTIGLIONE
JAN 13,2022
CHKD
DATE
DIVISION CODE
C
EMSD
DO NOT
SCALE
DRAWING
INTERPRET PER
ASME Y14.5 - 2018
MAX SURFACE ROUGHNESS
ALL SURFACES
MARKED ONLY
7
6
5
4
3
3M Center
St. Paul,
TOLERANCES
EXCEPT AS
NOTED
SCALE
THIRD ANGLE PROJECTION
8
ISSUE DATE AND DESCRIPTION
DRFT
2
INCHES
.0
.1
.00
.01
.000
.005
.0000
.0002
MILLIMETERS
0
.0
.00
.000
ANGLES
MN
55144
DRFT
CHKD
MFG
DATE
APPVL
DATE
S. NEU
JAN 13,2022
3M COPYRIGHT 2022
This document and the information it contains are
3M property and may not be reproduced or further
distributed without 3M permission, or used or
disclosed other than for 3M authorized purposes.
All rights reserved.
TITLE
TRIPOLARIZED HEADER,
4-WALL, LATCH/EJECT,
.050" X .100"
CAGE SIZE
NUMBER
MODEL
810
DRAWING NO.
REV.
78-5100-0253-4
DET.
LISTS
1
YES
NO
L
SHT 5 OF 5
Imaged: Central Standard Time 1/25/2022 -- UTC Offset (hrs) 6
C
A
工商网监
湘ICP备2023018690号
