HF100/10TP

8 TM 3M 7 6 5 4 3 2 1 NOTES TWISTED PAIR FLAT CABLE, HF100 SERIES .050" 28 AWG STRANDED, MASS TERMINABLE, HALOGEN FREE PO TABLE 1 19.68 [500] .71 SEE NOTE 5 1.97 [50] D .32 NO. OF CONDUCTORS 10 (5 PAIR) 14 (7 PAIR) 16 (8 PAIR) 20 (10 PAIR) 24 (12 PAIR) 26 (13 PAIR) 30 (15 PAIR) 34 (17 PAIR) 40 (20 PAIR) 50 (25 PAIR) 60 (32 PAIR) 64 (32 PAIR) 3M PART NUMBER HF100/10TP HF100/14TP HF100/16TP HF100/20TP HF100/24TP HF100/26TP HF100/30TP HF100/34TP HF100/40TP HF100/50TP HF100/60TP HF100/64TP DIM. "A" DIM. "B" .50 [12.7] .70 [17.8] .80 [20.3] 1.00 [2.4] 1.20 [30.5] 1.30 [33.0] 1.50 [38.1] 1.70 [43.2] 2.00 [50.8] 2.50 [63.5] 3.00 [76.2] 3.20 [81.3] .450+/-.010 [11.43] .650+/-.010 [15.88] .750+/-.010 [20.96] .950+/-.010 [22.23] 1.150+/-.010 [24.77] 1.250+/-.010 [31.12] 1.450+/-.015 [36.80] 1.650+/-.015 [37.47] 1.950+/-.015 [42.55] 2.450+/-.015 [50.17] 2.950+/-.015 [62.87] 3.150+/-.015 [80.01] * LOW SMOKE ZERO HALOGEN (LSZH) INSULATION. ADVANTAGES OF LSZH INSULATION ARE THE LOW SMOKE (IEC 61034-2-2005) AND LOW TOXICITY OF COMBUSTION GASES (NF X 70-100-2-2006), REDUCING THE RISK TO FIREFIGHTERS AND REDUCING THE SOOT AND CORROSION DAMAGE TO NEARBY EQUIPMENT. * 28 AWG WIRE ON .050 INCH CENTERS PERMITS MASS TERMINATION TO BROAD LINE OF IDC CONNECTORS. 1. REGULATORY INFORMATION: VISIT 3M.com/regs OR CONTACT YOUR 3M REPRESENTATIVE TO FIND THE RoHS COMPLIANCE STATUS OF THE 3M PART YOU ARE INTERESTED IN. 2 IN THE EVENT OF CONFLICT BETWEEN THIS DATA AND THAT CONTAINED IN THE PRODUCT SPECIFICATION, THE PRODUCT SPECIFICATION TAKES PRECEDENT. 4 BLUE EDGE CONDUCTOR DESIGNATES WIRE ONE OF PAIR ONE. 5 STANDARD PRODUCT HAS A 2" FLAT ON 19.7" REPEAT (50MM BOND ON 500MM REPEAT). FOR SPECIAL REQUIREMENTS, PLEASE CONTACT YOUR 3M SALES REPRESENTATIVE. THE FLAT CAN BE SPECIFIED ANYTHING OVER 1" {25MM}, THE REPEAT CAN BE SPECIFIED FROM 6.5" TO 48" {16.5CM TO 1.2M]. D DIM. "A" PHYSICAL: 2 .100 REF. INSULATION: MATERIAL: HALOGEN FREE POLYOLEFIN (PO) COLOR: BLUE / WHITE PAIRS 2.54 .07 C REF. C MARKING: STANDARD: NONE CANADIAN OPTION: SEE "PRINTING ILLUSTRATION" VIEW 1.8 CONDUCTORS: 28 AWG, 7 X 36 AWG [7 X .127] TINNED STRANDED COPPER SECTION THRU TWIST ELECTRICAL: TYP. 1.27 28 AWG 7 X 36 (7 X .127) TINNED STRANDED COPPER CONDUCTORS CHARACTERISTIC IMPEDANCE: CAPACITANCE: INDUCTANCE: PROPAGATION DELAY: VELOCITY OF PROPAGATION: BLUE (SEE NOTE 4) UNBALANCED 102 16.9 pF/ft [55.4 pF/m] .18 H/ft [.59 H/m] 1.74 ns/ft [5.71 ns/m] 58% BALANCED 119 14.6 pF/ft [47.9 pF/m] .21 H/ft [.69 H/m] 1.73 ns/ft [5.68 ns/m] 59% D .050 DRAWING NUMBER DARK GRAY EU: 1 X 10 /10ft. [3m] 78-5100-2344-9 2 NOTE: UNBALANCED IS MEASURED BETWEEN GROUND-SIGNAL-GROUND CONDUCTORS. BALANCED IS MEASURED BETWEEN CONDUCTORS WITHIN A PAIR. PO CARRIER B DIM. "B" PERTAINS TO BONDED AREA ONLY .043 .003 [1.09] 2 ENVIRONMENTAL: B TEMPERATURE RATING: -40 C TO +105 C (EIA-364-32G, METHOD A, TEST CONDITION 2) -15 C TO +105 C (UL TEMPERATUE RATING) FLAMMABILITY RATING: UL: HORIZONTAL HALOGEN FREE IS DEFINED AS BOTH 1) NO HALOGN COMPOUNDS THAT ARE INTENTIONALLY ADDED TO THE PRODUCT OR USED IN THE MANUFACTURING PROCESS FOR THE PRODUCT AND 2) ANY IMPURITIES PRESENT ARE LESS THAN 900ppm BROMINE, LESS THAN 900ppm CHLORINE AND/OR LESS THAN 1500ppm TOTAL BROMINE AND CHLORINE. THE LATTER ARE THE LEVELS SET FORTH IN CERTIAN INDUSTRY STANDARDS FOR PRINTED CIRCUIT BOARDS, SUCH AS THE INTERNATIONAL ELECTROTECHNICAL COMMISSION (IEC) 61249-2-21 STANDARDS. THIS INFORMATION REPRESENTS 3M'S KNOWLEDGE AND BELIEF WHICH MAY BE BASED IN WHOLE OR IN PART ON INFORMATION PROVIDED BY 3RD PARTY SUPPLIERS TO 3M. ORDERING INFORMATION HF100/XX TP XX BLANK = STANDARD SF = SPLICE FREE NUMBER OF CONDUCTORS (SEE TABLE) NOTE: AVAILABLE IN STANDARD LENGTHS OF 100 FT AND 300 FT PER ROLL, PLEASE SPECIFY WHEN ORDERING. D INCH [MM] TOLERANCE - UNLESS NOTED .X .XX .XXX [INCH] .1 .01 .005 [] = DIM. FOR REFERENCE ONLY CANADIAN OPTION "PRINTING ILLUSTRATION" R 3M ELECTRONICS MATERIALS SOLUTIONS DIVISION INTERCONNECT SOLUTIONS http://www.3Mconnectors.com AWM 21008 105 C 150V HOR DESIGN REFERENCE NEXT ASSEMBLY ACCESS CODES DIVISION DO NOT SCALE DRAWING INCHES MAX SURFACE ROUGHNESS ALL SURFACES MARKED ONLY 7 6 5 4 3 ISSUE DATE AND DESCRIPTION DATE CASTIGLIONE JUN 11,2018 CHKD DATE C 3M Center St. Paul, TOLERANCES EXCEPT AS NOTED INTERPRET PER ASME Y14.5 - 2009 UL FILE NO: E42769, UL STYLE NO: 21008 ECO DRFT EMSD SCALE THIRD ANGLE PROJECTION AWM 1A 105 C 150V FT2 EU