HSHM-S110APWR4-5AP1-TG30

3M™ MetPak™ HSHM Press-Fit Power Socket 2 mm Type A, 110/4 Signal/Power Contacts, 5 Rows, Right Angle HSHM Series • • • • • • • • • Up to 5 Gb/s data rates Low crosstalk at high frequencies 50/100 Ω (single-ended/differential) impedance Modular/scalable format IEC 61076-4-101 63 mated lines per linear inch Mates with 3M™ MetPak™ HSHM headers Dual beam contact construction for high reliability Four integrated 8.25 A power blades End-to-end stackable with 5 row 3M™ MetPak™ CP2, HM and HSHM sockets • See the Regulatory Information Appendix (RIA) in the “RoHS compliance” section of www.3mconnector.com for compliance information Date Modified: October 7, 2010  TS-2086-B Sheet 1 of 3 Physical Insulation: Material: High Temperature Thermoplastic (LCP) Flammability: UL 94V-0 Contact: Material: Copper Alloy Plating: See Ordering Information Performance Mechanical: Normal Force (Nominal): 0.57 N [58 g] Signal, 0.74 N [75 g] Shield, 0.98 N [100 g] Power Engagement Force (Nominal): 0.32 N [33 g] Signal, 0.22 N [22 g] Shield, 1.42 N [145 g] Power Separation Force (Nominal): 0.20 N [20 g] Signal, 0.20 N [20 g] Shield, 0.89 N [91 g] Power Wipe (Nominal, Shortest Contact): 2.67 mm [0.105 in] Signal, 1.57 mm [0.062 in] Shield, 1.93 mm [.076 in] Power Mate/Unmate Cycles: 250 Application: This module is not suitable for stand-alone use. Limited capture of 0.75 mm in Longitudinal and 1.00 mm transverse directions. (Refer to IEC-61076-4-101) Electrical: Data Rate: 5 Gb/s Characteristic Impedance: 50 Ω Single-ended, 100 Ω Differential Current Rating (Fully Loaded): 1 A @ 70° C Signal, 8.25 A @ 70°C Power Insulation Resistance: 104 MΩ @ 100 VDC Withstanding Voltage: 750 VRMS Environmental Temperature Rating: -55° C to 125° C UL File No.: E68080 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnector.com MetPak is a trademark of 3M Company. 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ MetPak™ HSHM Press-Fit Power Socket 2 mm Type A, 110/4 Signal/Power Contacts, 5 Rows, Right Angle HSHM Series 21.80 .858 20.40 .803 7.25 .285 HSHM-SXXXXX-5AP1-XXXXX REV X 8.70 .343 XXYY 2.50 .098 50.00 1.969 48.00 1.890 2.00 .079 2.50 .098 2.80 .110 3.30 .130 8.80 .346 10.70 .421 P2 P1 ROW E ROW D ROW C 2.00 .079 ROW B ROW A 25 24 23 22 21 20 19 18 17 16 15 P4 P3 11 10 9 8 7 6 5 4 3 2 1 46.00 1.811 6.50 .256 5.00 .197 mm (Inch) Tolerance Unless Noted Boxed leads are omitted on row differential pair connectors mm 0 ±3 0.0 0.00 ±0.3 ±0.13 [ ] Dimensions for Reference Only Ordering Information HSHM-S110APWRX-5AP1- XXXXX High Speed Option: 1 = Row differential applications 4 = Coaxial and column differential applications Plating μm [ μ” ]: TG30 = 0.76 [30] Min. Au Contact Area 2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply) 1.27 [50] Min. Ni All over Standard Option TG30L = 0.76 [30] Min. Au Contact Area, Lubricated 2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply) 1.27 [50] Min. Ni All over Typically higher make order quantities as compared to TG30. TG50 = 1.27 [50] Min. Au Contact Area, Lubricated 2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply) 1.27 [50] Min. Ni All over Non-Standard Option (Available with longer lead times and higher make order quantities, MOQ) TS-2086-B Sheet 2 of 3 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnector.com 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ MetPak™ HSHM Press-Fit Power Socket 2 mm Type A, 110/4 Signal/Power Contacts, 5 Rows, Right Angle HSHM Series 48.00 Ø DIM F 12X SEE TABLE Ø 0.10 M A B C 2.00 2.00 1.00 2.00 1.00 E D 2.00 C -C- 7.50 B 2.00 A 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 1 2 1.50 22.50 Ø DIM E 180X SEE TABLE Ø 0.10 M A B C 23.50 -A- -B- Recommended PCB hole mounting pattern for coaxial, Column differential and stripline applications.. E D C B A 25 24 23 22 21 20 19 18 17 16 15 11 10 9 8 7 6 5 4 3 2 1 Recommended PCB hole mounting pattern for row differential applications. (Same geometry as above without the ground vias.) Hole Plating Table mm [in.] DIA Finsihed Hole Dia. Cu. Thickness SnPb Thickness Drilled Hole Dia. E 0.457 - 0.559 [.0180 - .0220] 0.025 - 0.045 [.0010 - .0018] 0.008 -0.018 [.0003 - .0007] 0.584 - 0.625 [.0230 - .0246] F 0.690 - 0.790 [.0270 - .0310] 0.025 - 0.045 [.0010 - .0018] 0.008 -0.018 [.0003 - .0007] 0.810 - 0.860 [.0320 - .0340] TS-2086-B Sheet 3 of 3 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnector.com 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.  3M Electronics Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3Mconnector.com Please recycle. Printed in USA. © 3M 2010. All rights reserved. RIA-2217B-E 3M is a trademark of 3M Company.