25AA02E48/25AA02E64
2K SPI Bus Serial EEPROMs with EUI-48™ or EUI-64™ Node Identity
Device Selection Table
Part Number
VCC Range
Page Size
Temp. Ranges
Packages
Node Address
25AA02E48
1.8V-5.5V
16 Bytes
I
SN, OT
EUI-48™
25AA02E64
1.8V-5.5V
16 Bytes
I
SN, OT
EUI-64™
Features
Description
• Preprogrammed Globally Unique, 48-bit or 64-bit
Node Address
• Compatible with EUI-48™ and EUI-64™
• 10 MHz Maximum Clock Frequency
• Low-Power CMOS Technology:
- Maximum Write Current: 5 mA at 5.5V
- Read Current: 5 mA at 5.5V, 10 MHz
- Standby Current: 1 µA at 2.5V
• 256 x 8-bit Organization
• Write Page Mode (up to 16 bytes)
• Sequential Read
• Self-Timed Erase and Write Cycles
(5 ms maximum)
• Block Write Protection:
- Protect none, 1/4, 1/2 or all of array
• Built-in Write Protection:
- Power-on/off data protection circuitry
- Write enable latch
- Write-protect pin
• High Reliability:
- Endurance: 1,000,000 erase/write cycles
- Data retention: >200 years
- ESD protection: >4000V
• Temperature Ranges Supported:
- Industrial (I):
-40C to +85C
The
Microchip
Technology
Inc.
25AA02E48/25AA02E64 (25AA02EXX) is a 2 Kbit
Serial Electrically Erasable Programmable Read-Only
Memory (EEPROM). The memory is accessed via a
simple Serial Peripheral Interface (SPI) compatible
serial bus. The bus signals required are a clock input
(SCK) plus separate data in (SI) and data out (SO)
lines. Access to the device is controlled through a Chip
Select (CS) input.
• Pb-Free and RoHS Compliant
Package Types (not to scale)
6-Lead SOT-23
(OT)
SCK 1
6 VDD
VSS 2
5 CS
SI 3
4 SO
SOIC
(SN)
CS
1
8
VCC
SO
2
7
HOLD
WP
3
6
SCK
VSS
4
5
SI
2008-2018 Microchip Technology Inc.
Note:
25AA02EXX is used in this document as a
generic
part
number
for
the
25AA02E48/25AA02E64 devices.
Communication to the device can be paused via the
hold pin (HOLD). While the device is paused,
transitions on its inputs will be ignored, with the
exception of Chip Select, allowing the host to service
higher priority interrupts.
The 25AA02EXX is available in the standard 8-lead
SOIC and 6-lead SOT-23 packages.
Pin Function Table
Name
Function
CS
Chip Select Input
SO
Serial Data Output
WP
Write-Protect
VSS
Ground
SI
Serial Data Input
SCK
Serial Clock Input
HOLD
Hold Input
VCC
Supply Voltage
DS20002123G-page 1
25AA02E48/25AA02E64
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings(†)
VCC.............................................................................................................................................................................6.5V
All inputs and outputs w.r.t. VSS ..........................................................................................................-0.6V to VCC +1.0V
Storage temperature ................................................................................................................................. -65°C to 150°C
Ambient temperature under bias................................................................................................................. -40°C to 85°C
ESD protection on all pins.......................................................................................................................................... 4 kV
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for an
extended period of time may affect device reliability.
TABLE 1-1:
DC CHARACTERISTICS
DC CHARACTERISTICS
Param.
No.
Symbol
Industrial (I):
Characteristic
TA = -40°C to +85°C
Min.
Max.
Units
VCC = 1.8V to 5.5V
Test Conditions
D1
VIH1
High-Level Input Voltage
0.7 VCC
VCC +1
V
D2
VIL1
Low-Level Input Voltage
-0.3
0.3 VCC
V
VCC2.7V (Note 1)
D3
VIL2
Low-Level Input Voltage
-0.3
0.2 VCC
V
VCC < 2.7V (Note 1)
D4
VOL
Low-Level Output Voltage
—
0.4
V
IOL = 2.1 mA
D5
VOL
Low-Level Output Voltage
—
0.2
V
IOL = 1.0 mA, VCC < 2.5V
D6
VOH
High-Level Output Voltage
VCC -0.5
—
V
IOH = -400 µA
D7
ILI
Input Leakage Current
—
±1
µA
CS = VCC, VIN = VSS or VCC
D8
ILO
Output Leakage Current
—
±1
µA
CS = VCC, VOUT = VSS or VCC
D9
CINT
Internal Capacitance
(all inputs and outputs)
—
7
pF
TA = 25°C, CLK = 1.0 MHz,
VCC = 5.0V (Note 1)
D10
ICCREAD
Operating Current
—
5
mA
VCC = 5.5V; FCLK = 10.0 MHz,
SO = Open
—
2.5
mA
VCC = 2.5V; FCLK = 5.0 MHz,
SO = Open
—
5
mA
VCC = 5.5V
—
3
mA
VCC = 2.5V
—
1
µA
CS = VCC = 2.5V, Inputs tied to
VCC or VSS, TA = +85°C
D11
D12
ICCWRITE Operating Current
ICCS
Standby Current
Note 1: This parameter is periodically sampled and not 100% tested.
2008-2018 Microchip Technology Inc.
DS20002123G-page 2
25AA02E48/25AA02E64
TABLE 1-2:
AC CHARACTERISTICS
AC CHARACTERISTICS
Param.
Symbol
No.
1
FCLK
2
TCSS
3
TCSH
Characteristic
Clock Frequency
CS Setup Time
CS Hold Time
Industrial (I):
TA = -40°C to +85°C
VCC = 1.8V to 5.5V
Min.
Max.
Units
Test Conditions
—
10
MHz
4.5V VCC 5.5V
—
5
MHz
2.5V VCC 4.5V
—
3
MHz
1.8V VCC 2.5V
50
—
ns
4.5V VCC 5.5V
100
—
ns
2.5V VCC 4.5V
150
—
ns
1.8V VCC 2.5V
100
—
ns
4.5V VCC 5.5V
200
—
ns
2.5V VCC 4.5V
250
—
ns
1.8V VCC 2.5V
4
TCSD
CS Disable Time
50
—
ns
5
TSU
Data Setup Time
10
—
ns
4.5V VCC 5.5V
20
—
ns
2.5V VCC 4.5V
30
—
ns
1.8V VCC 2.5V
20
—
ns
4.5V VCC 5.5V
40
—
ns
2.5V VCC 4.5V
50
—
ns
1.8V VCC 2.5V
6
THD
Data Hold Time
7
TR
CLK Rise Time
—
100
ns
Note 1
8
TF
CLK Fall Time
—
100
ns
Note 1
9
THI
Clock High Time
50
—
ns
4.5V VCC 5.5V
100
—
ns
2.5V VCC 4.5V
150
—
ns
1.8V VCC 2.5V
50
—
ns
4.5V VCC 5.5V
100
—
ns
2.5V VCC 4.5V
150
—
ns
1.8V VCC 2.5V
10
TLO
Clock Low Time
11
TCLD
Clock Delay Time
50
—
ns
12
TCLE
Clock Enable Time
50
—
ns
13
TV
Output Valid from Clock
Low
—
50
ns
4.5V VCC 5.5V
—
100
ns
2.5V VCC 4.5V
—
160
ns
1.8V VCC 2.5V
0
—
ns
Note 1
14
THO
Output Hold Time
Note 1: This parameter is periodically sampled and not 100% tested.
2: TWC begins on the rising edge of CS after a valid write sequence and ends when the internal write cycle
is complete.
3: This parameter is not tested but ensured by characterization. For endurance estimates in a specific
application, please consult the Total Endurance™ Model which can be obtained from Microchip’s website
at www.microchip.com.
2008-2018 Microchip Technology Inc.
DS20002123G-page 3
25AA02E48/25AA02E64
TABLE 1-2:
AC CHARACTERISTICS (CONTINUED)
AC CHARACTERISTICS
Param.
Symbol
No.
15
TDIS
16
THS
17
THH
18
THZ
19
THV
20
TWC
21
Industrial (I):
Characteristic
TA = -40°C to +85°C
VCC = 1.8V to 5.5V
Min.
Max.
Units
—
40
ns
4.5V VCC 5.5V (Note 1)
—
80
ns
2.5V VCC 4.5V (Note 1)
—
160
ns
1.8V VCC 2.5V (Note 1)
20
—
ns
4.5V VCC 5.5V
40
—
ns
2.5V VCC 4.5V
80
—
ns
1.8V VCC 2.5V
20
—
ns
4.5V VCC 5.5V
40
—
ns
2.5V VCC 4.5V
80
—
ns
1.8V VCC 2.5V
30
—
ns
4.5V VCC 5.5V (Note 1)
60
—
ns
2.5V VCC 4.5V (Note 1)
160
—
ns
1.8V VCC 2.5V (Note 1)
30
—
ns
4.5V VCC 5.5V
60
—
ns
2.5V VCC 4.5V
160
—
ns
1.8V VCC 2.5V
Internal Write Cycle Time
(byte or page)
—
5
ms
Note 2
Endurance
1M
—
Output Disable Time
HOLD Setup Time
HOLD Hold Time
HOLD Low to Output
High-Z
HOLD High to Output
Valid
Test Conditions
E/W 25°C, VCC = 5.5V (Note 3)
cycles
Note 1: This parameter is periodically sampled and not 100% tested.
2: TWC begins on the rising edge of CS after a valid write sequence and ends when the internal write cycle
is complete.
3: This parameter is not tested but ensured by characterization. For endurance estimates in a specific
application, please consult the Total Endurance™ Model which can be obtained from Microchip’s website
at www.microchip.com.
TABLE 1-3:
AC TEST CONDITIONS
AC Waveform
VLO = 0.2V
VHI = VCC - 0.2V
Note 1
VHI = 4.0V
Note 2
CL = 100 pF
Timing Measurement Reference Level
Input
0.5 VCC
Output
0.5 VCC
Note 1: For VCC 4.0V
2: For VCC 4.0V
2008-2018 Microchip Technology Inc.
DS20002123G-page 4
25AA02E48/25AA02E64
FIGURE 1-1:
HOLD TIMING
CS
17
16
17
16
SCK
18
SO
n+2
SI
n+2
n+1
n
19
High-Impedance
n
5
Don’t Care
n+1
n-1
n
n
n-1
HOLD
FIGURE 1-2:
SERIAL INPUT TIMING
4
CS
2
7
Mode 1,1
12
11
8
3
SCK Mode 0,0
5
SI
6
MSB In
LSB In
High-Impedance
SO
FIGURE 1-3:
SERIAL OUTPUT TIMING
CS
9
3
10
Mode 1,1
SCK
Mode 0,0
13
14
SO
MSB Out
SI
2008-2018 Microchip Technology Inc.
15
ISB Out
Don’t Care
DS20002123G-page 5
25AA02E48/25AA02E64
2.0
FUNCTIONAL DESCRIPTION
2.1
Principles of Operation
The 25AA02EXX is a 256-byte Serial EEPROM
designed to interface directly with the Serial Peripheral
Interface (SPI) port of many of today’s popular
microcontroller families, including Microchip’s PIC®
microcontrollers. It may also interface with
microcontrollers that do not have a built-in SPI port by
using discrete I/O lines programmed properly in
software to match the SPI protocol.
The 25AA02EXX contains an 8-bit instruction register.
The device is accessed via the SI pin, with data being
clocked in on the rising edge of SCK. The CS pin must
be low and the HOLD pin must be high for the entire
operation.
Table 2-1 contains a list of the possible instruction
bytes and format for device operation. All instructions,
addresses, and data are transferred MSb first, LSb last.
Data (SI) is sampled on the first rising edge of SCK
after CS goes low. If the clock line is shared with other
peripheral devices on the SPI bus, the user can assert
the HOLD input and place the 25AA02EXX in ‘HOLD’
mode. After releasing the HOLD pin, operation will
resume from the point when the HOLD was asserted.
2.2
Read Sequence
The device is selected by pulling CS low. The 8-bit
READ instruction is transmitted to the 25AA02EXX
followed by an 8-bit address. See Figure 2-1 for more
details.
After the correct READ instruction and address are sent,
the data stored in the memory at the selected address
is shifted out on the SO pin. Data stored in the memory
at the next address can be read sequentially by
continuing to provide clock pulses to the slave. The
internal Address Pointer automatically increments to
the next higher address after each byte of data is
shifted out. When the highest address is reached
(FFh), the address counter rolls over to address 00h
allowing the read cycle to be continued indefinitely. The
read operation is terminated by raising the CS pin
(Figure 2-1).
2.3
Write Sequence
After setting the write enable latch, the user may
proceed by driving CS low, issuing a WRITE instruction,
followed by the remainder of the address, and then the
data to be written. Up to 16 bytes of data can be sent to
the device before a write cycle is necessary. The only
restriction is that all of the bytes must reside in the
same page. Additionally, a page address begins with
XXXX 0000 and ends with XXXX 1111. If the internal
address counter reaches XXXX 1111 and clock signals
continue to be applied to the chip, the address counter
will roll back to the first address of the page and
over-write any data that previously existed in those
locations.
Note:
Page write operations are limited to
writing bytes within a single physical page,
regardless of the number of bytes
actually being written. Physical page
boundaries start at addresses that are
integer multiples of the page buffer size
(or ‘page size’) and, end at addresses that
are integer multiples of page size – 1. If a
Page Write command attempts to write
across a physical page boundary, the
result is that the data wraps around to the
beginning of the current page (overwriting
data previously stored there), instead of
being written to the next page as might be
expected. It is, therefore, necessary for
the application software to prevent page
write operations that would attempt to
cross a page boundary.
For the data to be actually written to the array, the CS
must be brought high after the Least Significant bit (D0)
of the nth data byte has been clocked in. If CS is driven
high at any other time, the write operation will not be
completed. Refer to Figure 2-2 and Figure 2-3 for more
detailed illustrations on the byte write sequence and
the page write sequence, respectively. While the write
is in progress, the STATUS register may be read to
check the status of the WIP, WEL, BP1 and BP0 bits
(Figure 2-6). Attempting to read a memory array
location will not be possible during a write cycle. Polling
the WIP bit in the STATUS register is recommended in
order to determine if a write cycle is in progress. When
the write cycle is completed, the write enable latch is
reset.
Prior to any attempt to write data to the 25AA02EXX,
the write enable latch must be set by issuing the WREN
instruction (Figure 2-4). This is done by setting CS low
and then clocking out the proper instruction into the
25AA02EXX. After all eight bits of the instruction are
transmitted, CS must be driven high to set the write
enable latch. If the write operation is initiated
immediately after the WREN instruction without CS
driven high, data will not be written to the array since
the write enable latch was not properly set.
2008-2018 Microchip Technology Inc.
DS20002123G-page 6
25AA02E48/25AA02E64
BLOCK DIAGRAM
STATUS
Register
HV Generator
Memory
Control
Logic
I/O Control
Logic
EEPROM
Array
X
Dec
Page Latches
SI
SO
Y Decoder
CS
SCK
Sense Amp.
R/W Control
HOLD
WP
VCC
VSS
TABLE 2-1:
INSTRUCTION SET
Instruction Name
Instruction Format
Description
READ
0000 x011
Read data from memory array beginning at selected address
WRITE
0000 x010
Write data to memory array beginning at selected address
WRDI
0000 x100
Reset the write enable latch (disable write operations)
WREN
0000 x110
Set the write enable latch (enable write operations)
RDSR
0000 x101
Read STATUS register
WRSR
0000 x001
Write STATUS register
x = don’t care
FIGURE 2-1:
READ SEQUENCE
CS
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
SCK
Instruction
SI
0
0
0
0
0
Address Byte
0
1
1 A7 A6 A5 A4 A3 A2 A1 A0
Data Out
High-Impedance
SO
2008-2018 Microchip Technology Inc.
7
6
5
4
3
2
1
0
DS20002123G-page 7
25AA02E48/25AA02E64
FIGURE 2-2:
BYTE WRITE SEQUENCE
CS
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Twc
SCK
Instruction
SI
0
0
0
0
0
Address Byte
0
Data Byte
0 A7 A6 A5 A4 A3 A2 A1 A0
1
7
6
5
4
3
2
1
0
High-Impedance
SO
FIGURE 2-3:
PAGE WRITE SEQUENCE
CS
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
SCK
Address Byte
Instruction
SI
0
0
0
0
0
0 1
Data Byte 1
0 A7 A6 A5 A4 A3 A2 A1 A0 7
6
5
4
3
2
1
0
CS
24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
SCK
Data Byte 2
SI
7
6
5
4
3
2
2008-2018 Microchip Technology Inc.
Data Byte 3
1
0
7
6
5
4
3
2
Data Byte n (16 max)
1
0
7
6
5
4
3
2
1
0
DS20002123G-page 8
25AA02E48/25AA02E64
2.4
Write Enable (WREN) and Write
Disable (WRDI)
The following is a list of conditions under which the
write enable latch will be reset:
•
•
•
•
•
The 25AA02EXX contains a write enable latch. See
Table 2-4 for the Write-Protect Functionality Matrix.
This latch must be set before any write operation will be
completed internally. The WREN instruction will set the
latch, and the WRDI will reset the latch.
FIGURE 2-4:
Power-up
WRDI instruction successfully executed
WRSR instruction successfully executed
WRITE instruction successfully executed
WP pin is brought low
WRITE ENABLE SEQUENCE (WREN)
CS
0
1
2
3
4
5
6
7
SCK
0
SI
0
0
0
0
1
1
0
High-Impedance
SO
FIGURE 2-5:
WRITE DISABLE SEQUENCE (WRDI)
CS
0
1
2
3
4
5
6
7
SCK
SI
0
0
0
0
0
1
0
0
High-Impedance
SO
2008-2018 Microchip Technology Inc.
DS20002123G-page 9
25AA02E48/25AA02E64
2.5
Read Status Register Instruction
(RDSR)
The Write Enable Latch (WEL) bit indicates the status
of the write enable latch and is read-only. When set to
a ‘1’, the latch allows writes to the array, when set to a
‘0’, the latch prohibits writes to the array. The state of
this bit can always be updated via the WREN or WRDI
commands regardless of the state of write protection
on the STATUS register. These commands are shown
in Figure 2-4 and Figure 2-5.
The Read Status Register instruction (RDSR) provides
access to the STATUS register. See Figure 2-6 for the
RDSR timing sequence. The STATUS register may be
read at any time, even during a write cycle. The
STATUS register is formatted as follows:
TABLE 2-2:
The Block Protection (BP0 and BP1) bits indicate
which blocks are currently write-protected. These bits
are set by the user issuing the WRSR instruction, which
is shown in Figure 2-7. These bits are nonvolatile and
are described in more detail in Table 2-3.
STATUS REGISTER
7
6 5 4
3
2
1
–
– – – W/R W/R
R
X
X X X BP1 BP0 WEL
W/R = writable/readable. R = read-only.
0
R
WIP
The Write-In-Process (WIP) bit indicates whether the
25AA02EXX is busy with a write operation. When set to
a ‘1’, a write is in progress, when set to a ‘0’, no write is
in progress. This bit is read-only.
FIGURE 2-6:
READ STATUS REGISTER TIMING SEQUENCE (RDSR)
CS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
0
SCK
Instruction
SI
0
0
0
0
0
1
0
1
Data from STATUS register
High-Impedance
SO
2008-2018 Microchip Technology Inc.
7
6
5
4
3
2
DS20002123G-page 10
25AA02E48/25AA02E64
2.6
TABLE 2-3:
Write Status Register Instruction
(WRSR)
The Write Status Register instruction (WRSR) allows
the user to write to the nonvolatile bits in the STATUS
register as shown in Table 2-2. See Figure 2-7 for the
WRSR timing sequence. Four levels of protection for
the array are selectable by writing to the appropriate
bits in the STATUS register. The user has the ability to
write-protect none, one, two, or all four of the
segments of the array as shown in Table 2-3.
FIGURE 2-7:
ARRAY PROTECTION
BP1
BP0
Array Addresses
Write-Protected
0
0
none
0
1
upper 1/4
(C0h-FFh)
1
0
upper 1/2
(80h-FFh)
1
1
all
(00h-FFh)
WRITE STATUS REGISTER TIMING SEQUENCE (WRSR)
CS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
0
SCK
Instruction
SI
0
0
0
0
Data to STATUS register
0
0
0
1
7
6
5
4
3
2
High-Impedance
SO
2008-2018 Microchip Technology Inc.
DS20002123G-page 11
25AA02E48/25AA02E64
2.7
Data Protection
2.8
The following protection has been implemented to
prevent inadvertent writes to the array:
• The write enable latch is reset on power-up
• A write enable instruction must be issued to set
the write enable latch
• After a byte write, page write or STATUS register
write, the write enable latch is reset
• CS must be set high after the proper number of
clock cycles to start an internal write cycle
• Access to the array during an internal write cycle
is ignored and programming is continued
TABLE 2-4:
WP
(pin 3)
0 (low)
1 (high)
1 (high)
x = don’t care
Power-On State
The 25AA02EXX powers on in the following state:
• The device is in low-power Standby mode
(CS = 1)
• The write enable latch is reset
• SO is in high-impedance state
• A high-to-low-level transition on CS is required to
enter active state
WRITE-PROTECT FUNCTIONALITY MATRIX
WEL
(SR bit 1)
Protected Blocks
Unprotected Blocks
STATUS Register
x
0
1
Protected
Protected
Protected
Protected
Protected
Writable
Protected
Protected
Writable
2008-2018 Microchip Technology Inc.
DS20002123G-page 12
25AA02E48/25AA02E64
3.0
PREPROGRAMMED EUI-48™
OR EUI-64™ NODE ADDRESS
The 25AA02EXX is programmed at the factory with a
globally unique node address stored in the upper 1/4 of
the array and write-protected through the STATUS
register. The remaining 1,536 bits are available for
application use.
FIGURE 3-1:
MEMORY ORGANIZATION
00h
3.2
The 6-byte EUI-48™ node address value of the
25AA02E48 is stored in array locations 0xFA through
0xFF, as shown in Figure 3-2. The first three bytes are
the Organizationally Unique Identifier (OUI) assigned
to Microchip by the IEEE Registration Authority. The
remaining three bytes are the Extension Identifier, and
are generated by Microchip to ensure a globally
unique, 48-bit value.
3.2.1
Standard
EEPROM
Write-Protected
Node Address Block
3.1
C0h
FFh
Factory-Programmed Write
Protection
6
X
—
5
X
—
4
X
—
3
BP1
0
2
BP0
1
1
WEL
—
0
WIP
—
This protects the upper 1/4 of the array (0xC0 to 0xFF)
from write operations. This array block can be utilized
for writing by clearing the BP bits with a Write Status
Register (WRSR) instruction. Note that if this is
performed, care must be taken to prevent overwriting
the node address value.
Note:
3.2.2
The OUI will change as addresses are
exhausted. Customers are not guaranteed to receive a specific OUI and should
design their application to accept new
OUIs as they are introduced.
EUI-64™ SUPPORT USING THE
25AA02E48
The preprogrammed EUI-48 node address of the
25AA02E48 can easily be encapsulated at the
application level to form a globally unique, 64-bit node
address for systems utilizing the EUI-64 standard. This
is done by adding 0xFFFE between the OUI and the
Extension Identifier, as shown below.
Note:
2008-2018 Microchip Technology Inc.
ORGANIZATIONALLY UNIQUE
IDENTIFIERS (OUIs)
Each OUI provides roughly 16M (224) addresses. Once
the address pool for an OUI is exhausted, Microchip
will acquire a new OUI from IEEE to use for
programming this model. For more information on past
and current OUIs see “Organizationally Unique
Identifiers For Preprogrammed EUI-48 and EUI-64
Address Devices” Technical Brief (DS90003187).
In order to help guard against accidental corruption of
the node address, the BP1 and BP0 bits of the STATUS
register are programmed at the factory to ‘0’ and ‘1’,
respectively, as shown in the following table:
7
X
—
EUI-48™ Node Address
(25AA02E48)
As an alternative, the 25AA02E64
features an EUI-64 node address that can
be used in EUI-64 applications directly
without the need for encapsulation,
thereby simplifying system software. See
Section 3.3 “EUI-64™ Node Address
(25AA02E64)” for details.
DS20002123G-page 13
25AA02E48/25AA02E64
FIGURE 3-2:
EUI-48 NODE ADDRESS PHYSICAL MEMORY MAP EXAMPLE (25AA02E48)
Description
24-bit Organizationally
Unique Identifier
Data
00h
Array
Address
FAh
04h
A3h
24-bit Extension
Identifier
12h
34h
56h
FFh
Corresponding EUI-48™ Node Address: 00-04-A3-12-34-56
Corresponding EUI-64™ Node Address After Encapsulation: 00-04-A3-FF-FE-12-34-56
2008-2018 Microchip Technology Inc.
DS20002123G-page 14
25AA02E48/25AA02E64
EUI-64™ Node Address
(25AA02E64)
3.3
The 8-byte EUI-64™ node address value of the
25AA02E64 is stored in array locations 0xF8 through
0xFF, as shown in Figure 3-3. The first three bytes are
the Organizationally Unique Identifier (OUI) assigned
to Microchip by the IEEE Registration Authority. The
remaining five bytes are the Extension Identifier, and
are generated by Microchip to ensure a globally
unique, 64-bit value.
Note:
In conformance with IEEE guidelines,
Microchip will not use the values 0xFFFE
and 0xFFFF for the first two bytes of the
EUI-64 Extension Identifier. These two
values are specifically reserved to allow
applications to encapsulate EUI-48
addresses into EUI-64 addresses.
FIGURE 3-3:
Description
EUI-64 NODE ADDRESS PHYSICAL MEMORY MAP EXAMPLE (25AA02E64)
40-bit Extension
Identifier
24-bit Organizationally
Unique Identifier
Data
00h
Array
Address
F8h
04h
A3h
12h
34h
56h
78h
90h
FFh
Corresponding EUI-64™ Node Address: 00-04-A3-12-34-56-78-90
2008-2018 Microchip Technology Inc.
DS20002123G-page 15
25AA02E48/25AA02E64
4.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 4-1.
TABLE 4-1:
4.1
PIN FUNCTION TABLE
Name
SOIC
SOT-23
Function
CS
1
5
Chip Select Input
SO
2
4
Serial Data Output
WP
3
—
Write-Protect Pin
VSS
4
2
Ground
SI
5
3
Serial Data Input
SCK
6
1
Serial Clock Input
HOLD
7
—
Hold Input
VCC
8
6
Supply Voltage
Chip Select (CS)
A low level on this pin selects the device. A high level
deselects the device and forces it into Standby mode.
However, a programming cycle which is already
initiated or in progress will be completed, regardless of
the CS input signal. If CS is brought high during a
program cycle, the device will go into Standby mode as
soon as the programming cycle is complete. When the
device is deselected, SO goes to the high-impedance
state, allowing multiple parts to share the same SPI
bus. A low-to-high transition on CS after a valid write
sequence initiates an internal write cycle. After
power-up, a low level on CS is required prior to any
sequence being initiated.
4.2
Serial Output (SO)
The SO pin is used to transfer data out of the
25AA02EXX. During a read cycle, data is shifted out on
this pin after the falling edge of the serial clock.
4.3
Write-Protect (WP)
The WP pin is a hardware write-protect input pin.
When it is low, all writes to the array or STATUS
register are disabled, but any other operations
function normally. When WP is high, all functions,
including nonvolatile writes, operate normally. At any
time when WP is low, the write enable Reset latch will
be reset and programming will be inhibited. However,
if a write cycle is already in progress, WP going low
will not change or disable the write cycle. See
Table 2-4 for the Write-Protect Functionality Matrix.
4.4
4.5
Serial Clock (SCK)
The SCK is used to synchronize the communication
between a master and the 25AA02EXX. Instructions,
addresses or data present on the SI pin are latched on
the rising edge of the clock input, while data on the SO
pin is updated after the falling edge of the clock input.
4.6
Hold (HOLD)
The HOLD pin is used to suspend transmission to the
25AA02EXX while in the middle of a serial sequence
without having to retransmit the entire sequence again.
It must be held high any time this function is not being
used. Once the device is selected and a serial
sequence is underway, the HOLD pin may be pulled
low to pause further serial communication without
resetting the serial sequence. The HOLD pin must be
brought low while SCK is low, otherwise the HOLD
function will not be invoked until the next SCK
high-to-low transition. The 25AA02EXX must remain
selected during this sequence. The SI, SCK and SO
pins are in a high-impedance state during the time the
device is paused and transitions on these pins will be
ignored. To resume serial communication, HOLD must
be brought high while the SCK pin is low, otherwise
serial communication will not resume. Lowering the
HOLD line at any time will tri-state the SO line.
Serial Input (SI)
The SI pin is used to transfer data into the device. It
receives instructions, addresses and data. Data is
latched on the rising edge of the serial clock.
2008-2018 Microchip Technology Inc.
DS20002123G-page 16
25AA02E48/25AA02E64
5.0
PACKAGING INFORMATION
5.1
Package Marking Information*
8-Lead SOIC
Example
25A2E48I
SN e3 1627
1L7
XXXXXXXT
XXXXYYWW
NNN
6-Lead SOT-23 (25AA02E48)
Example
XXNN
20L7
6-Lead SOT-23 (25AA02E64)
Example
XXXXY
WWNNN
AAAA6
271L7
1st Line Marking Code
Part Number
SOIC
SOT-23
25AA02E48
25A2E48I
20NN
25AA02E64
25A2E64I
AAAAY
Legend: XX...X
T
Y
YY
WW
NNN
e3
Part number or part number code
Temperature (I, E)
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code (2 characters for small packages)
Pb-free** JEDEC® designator for Matte Tin (Sn)
* Standard OTP marking consists of Microchip part number, year code, week code,
and traceability code.
** Please visit www.microchip.com/Pbfree for the latest information on Pb-free
conversion.
Note:
For very small packages with no room for the Pb-free JEDEC designator
e3 , the marking will only appear on the outer carton or reel label.
Note:
In the event the full Microchip part number cannot be marked on one line, it
will be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
2008-2018 Microchip Technology Inc.
DS20002123G-page 17
25AA02E48/25AA02E64
8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2X
0.10 C A–B
D
A
D
NOTE 5
N
E
2
E1
2
E1
E
NOTE 1
2
1
e
B
NX b
0.25
C A–B D
NOTE 5
TOP VIEW
0.10 C
C
A A2
SEATING
PLANE
8X
A1
SIDE VIEW
0.10 C
h
R0.13
h
R0.13
H
SEE VIEW C
VIEW A–A
0.23
L
(L1)
VIEW C
Microchip Technology Drawing No. C04-057-SN Rev D Sheet 1 of 2
2008-2018 Microchip Technology Inc.
DS20002123G-page 18
25AA02E48/25AA02E64
8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
Units
Dimension Limits
Number of Pins
N
e
Pitch
Overall Height
A
Molded Package Thickness
A2
§
Standoff
A1
Overall Width
E
Molded Package Width
E1
Overall Length
D
Chamfer (Optional)
h
Foot Length
L
Footprint
L1
Foot Angle
c
Lead Thickness
b
Lead Width
Mold Draft Angle Top
Mold Draft Angle Bottom
MIN
1.25
0.10
0.25
0.40
0°
0.17
0.31
5°
5°
MILLIMETERS
NOM
8
1.27 BSC
6.00 BSC
3.90 BSC
4.90 BSC
1.04 REF
-
MAX
1.75
0.25
0.50
1.27
8°
0.25
0.51
15°
15°
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. § Significant Characteristic
3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or
protrusions shall not exceed 0.15mm per side.
4. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
5. Datums A & B to be determined at Datum H.
Microchip Technology Drawing No. C04-057-SN Rev D Sheet 2 of 2
2008-2018 Microchip Technology Inc.
DS20002123G-page 19
25AA02E48/25AA02E64
8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm Body [SOIC]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
SILK SCREEN
C
Y1
X1
E
RECOMMENDED LAND PATTERN
Units
Dimension Limits
E
Contact Pitch
Contact Pad Spacing
C
Contact Pad Width (X8)
X1
Contact Pad Length (X8)
Y1
MIN
MILLIMETERS
NOM
1.27 BSC
5.40
MAX
0.60
1.55
Notes:
1. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
Microchip Technology Drawing C04-2057-SN Rev B
2008-2018 Microchip Technology Inc.
DS20002123G-page 20
25AA02E48/25AA02E64
6-Lead Plastic Small Outline Transistor (OT, OTY) [SOT-23]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2X
0.15 C A-B
D
e1
A
D
E
2
E1
E
E1
2
2X
0.15 C D
2X
0.20 C A-B
e
6X b
B
0.20
C A-B D
TOP VIEW
C
A
A2
SEATING PLANE
6X
A1
0.10 C
SIDE VIEW
R1
L2
R
c
GAUGE PLANE
L
Ĭ
(L1)
END VIEW
Microchip Technology Drawing C04-028C (OT) Sheet 1 of 2
2008-2018 Microchip Technology Inc.
DS20002123G-page 21
25AA02E48/25AA02E64
6-Lead Plastic Small Outline Transistor (OT, OTY) [SOT-23]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
Units
Dimension Limits
N
Number of Leads
e
Pitch
Outside lead pitch
e1
Overall Height
A
Molded Package Thickness
A2
Standoff
A1
Overall Width
E
Molded Package Width
E1
Overall Length
D
Foot Length
L
Footprint
L1
Seating Plane to Gauge Plane
L1
φ
Foot Angle
c
Lead Thickness
Lead Width
b
MIN
0.90
0.89
0.00
0.30
0°
0.08
0.20
MILLIMETERS
NOM
6
0.95 BSC
1.90 BSC
1.15
2.80 BSC
1.60 BSC
2.90 BSC
0.45
0.60 REF
0.25 BSC
-
MAX
1.45
1.30
0.15
0.60
10°
0.26
0.51
Notes:
1. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or
protrusions shall not exceed 0.25mm per side.
2. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-028C (OT) Sheet 2 of 2
2008-2018 Microchip Technology Inc.
DS20002123G-page 22
25AA02E48/25AA02E64
6-Lead Plastic Small Outline Transistor (OT, OTY) [SOT-23]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
GX
Y
Z
C G
G
SILK SCREEN
X
E
RECOMMENDED LAND PATTERN
Units
Dimension Limits
E
Contact Pitch
C
Contact Pad Spacing
X
Contact Pad Width (X3)
Y
Contact Pad Length (X3)
G
Distance Between Pads
Distance Between Pads
GX
Z
Overall Width
MIN
MILLIMETERS
NOM
0.95 BSC
2.80
MAX
0.60
1.10
1.70
0.35
3.90
Notes:
1. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
Microchip Technology Drawing No. C04-2028B (OT)
2008-2018 Microchip Technology Inc.
DS20002123G-page 23
25AA02E48/25AA02E64
APPENDIX A:
REVISION HISTORY
Revision A (12/08)
Initial release of this document.
Revision B (04/10)
Removed Preliminary status; Revised Section 2.0;
Add sentence to Section 3.0; Add SOT-23 Land
Pattern.
Revision C (12/2012)
Revised Table 1-2, Parameter 21.
Revision D (4/2013)
Added 25AA02E64 part number.
Revision E (01/2015)
Updated Section 3.0; Updated Product Identification
System.
Revision F (07/2016)
Added new OUI (54-10-EC) to list.
Revision G (02/2018)
Added detailed description of OUIs.
2008-2018 Microchip Technology Inc.
DS20002123G-page 24
25AA02E48/25AA02E64
THE MICROCHIP WEBSITE
CUSTOMER SUPPORT
Microchip provides online support via our website at
www.microchip.com. This website is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the website contains the following information:
Users of Microchip products can receive assistance
through several channels:
• Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
• General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Customers
should
contact
their
distributor,
representative or Field Application Engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
Technical support is available through the website
at: http://microchip.com/support
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip website at
www.microchip.com. Under “Support”, click on
“Customer Change Notification” and follow the
registration instructions.
2008-2018 Microchip Technology Inc.
DS20002123G-page 25
25AA02E48/25AA02E64
NOTES:
2008-2018 Microchip Technology Inc.
DS20002123G-page 26
25AA02E48/25AA02E64
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
(1)
[X](1)
X
/XX
Device
Tape and Reel
Option
Temperature
Range
Package
Examples:
a)
b)
Device:
25AA02E48 =
2 Kbit, 1.8V, 16-Byte Page, SPI Serial EEPROM
with EUI-48™ Node Identity
25AA02E64 =
2 Kbit, 1.8V, 16-Byte Page, SPI Serial EEPROM
with EUI-64™ Node Identity
Tape and Reel
Option:
Blank
T
=
=
Standard packaging (tube or tray)
Tape and Reel(1)
Temperature
Range:
I
=
-40C to+85C
Package:
SN
OT
=
=
Plastic SOIC (3.90 mm body), 8-lead
SOT-23, 6-lead (Tape and Reel only)
c)
d)
e)
f)
25AA02E48-I/SN = 2 Kbit, 16-byte page, 1.8V
Serial EEPROM with EUI-48
Node Identity, Industrial temperature, SOIC package.
25AA02E48T-I/SN = 2 Kbit, 16-byte page, 1.8V
Serial EEPROM with EUI-48
Node Identity, Tape & Reel,
Industrial temp.,
SOIC package.
25AA02E48T-I/OT = 2 Kbit, 16-byte page, 1.8V
Serial EEPROM with EUI-48
Node Identity, Tape & Reel,
Industrial temp.,
SOT-23 package.
25AA02E64-I/SN = 2 Kbit, 16-byte page, 1.8V
Serial EEPROM with EUI-64
Node Identity, Industrial
temp., SOIC package.
25AA02E64T-I/SN = 2 Kbit, 16-byte page, 1.8V
Serial EEPROM with EUI-64
Node Identity, Tape & Reel,
Industrial temp., SOIC package.
25AA02E64T-I/OT = 2 Kbit, 16-byte page, 1.8V
Serial EEPROM with EUI-64
Node Identity, Tape & Reel,
Industrial temp., SOT-23
package.
Note 1: Tape and Reel identifier only appears in
the catalog part number description. This
identifier is used for ordering purposes
and is not printed on the device package.
Check with your Microchip Sales Office
for package availability with the Tape and
Reel option.
2008-2018 Microchip Technology Inc.
DS20002123G-page 27
25AA02E48/25AA02E64
NOTES:
2008-2018 Microchip Technology Inc.
DS20002123G-page 28
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights unless otherwise stated.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
Trademarks
The Microchip name and logo, the Microchip logo, AnyRate, AVR,
AVR logo, AVR Freaks, BeaconThings, BitCloud, chipKIT, chipKIT
logo, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR,
Heldo, JukeBlox, KEELOQ, KEELOQ logo, Kleer, LANCheck, LINK
MD, maXStylus, maXTouch, MediaLB, megaAVR, MOST, MOST
logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32
logo, Prochip Designer, QTouch, RightTouch, SAM-BA, SpyNIC,
SST, SST Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are
registered trademarks of Microchip Technology Incorporated in
the U.S.A. and other countries.
ClockWorks, The Embedded Control Solutions Company,
EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS,
mTouch, Precision Edge, and Quiet-Wire are registered
trademarks of Microchip Technology Incorporated in the U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any
Capacitor, AnyIn, AnyOut, BodyCom, CodeGuard,
CryptoAuthentication, CryptoCompanion, CryptoController,
dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM,
ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, InterChip Connectivity, JitterBlocker, KleerNet, KleerNet logo, Mindi,
MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB,
MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation,
PICDEM, PICDEM.net, PICkit, PICtail, PureSilicon, QMatrix,
RightTouch logo, REAL ICE, Ripple Blocker, SAM-ICE, Serial
Quad I/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II,
Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan,
WiperLock, Wireless DNA, and ZENA are trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in
the U.S.A.
Silicon Storage Technology is a registered trademark of Microchip
Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology
Germany II GmbH & Co. KG, a subsidiary of Microchip Technology
Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
© 2008-2018, Microchip Technology Incorporated, All Rights
Reserved.
ISBN: 978-1-5224-2725-4
== ISO/TS 16949 ==
2008-2018 Microchip Technology Inc.
DS20002123G-page 29
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Australia - Sydney
Tel: 61-2-9868-6733
India - Bangalore
Tel: 91-80-3090-4444
China - Beijing
Tel: 86-10-8569-7000
India - New Delhi
Tel: 91-11-4160-8631
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
China - Chengdu
Tel: 86-28-8665-5511
India - Pune
Tel: 91-20-4121-0141
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
China - Chongqing
Tel: 86-23-8980-9588
Japan - Osaka
Tel: 81-6-6152-7160
Finland - Espoo
Tel: 358-9-4520-820
China - Dongguan
Tel: 86-769-8702-9880
Japan - Tokyo
Tel: 81-3-6880- 3770
China - Guangzhou
Tel: 86-20-8755-8029
Korea - Daegu
Tel: 82-53-744-4301
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
China - Hangzhou
Tel: 86-571-8792-8115
Korea - Seoul
Tel: 82-2-554-7200
China - Hong Kong SAR
Tel: 852-2943-5100
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
China - Nanjing
Tel: 86-25-8473-2460
Malaysia - Penang
Tel: 60-4-227-8870
China - Qingdao
Tel: 86-532-8502-7355
Philippines - Manila
Tel: 63-2-634-9065
China - Shanghai
Tel: 86-21-3326-8000
Singapore
Tel: 65-6334-8870
China - Shenyang
Tel: 86-24-2334-2829
Taiwan - Hsin Chu
Tel: 886-3-577-8366
China - Shenzhen
Tel: 86-755-8864-2200
Taiwan - Kaohsiung
Tel: 886-7-213-7830
China - Suzhou
Tel: 86-186-6233-1526
Taiwan - Taipei
Tel: 886-2-2508-8600
China - Wuhan
Tel: 86-27-5980-5300
Thailand - Bangkok
Tel: 66-2-694-1351
China - Xian
Tel: 86-29-8833-7252
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
China - Xiamen
Tel: 86-592-2388138
China - Zhuhai
Tel: 86-756-3210040
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
2008-2018 Microchip Technology Inc.
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-67-3636
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Israel - Ra’anana
Tel: 972-9-744-7705
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Padova
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-7289-7561
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
DS20002123G-page 30
10/25/17