KSZ8463ML/RL/FML/FRL
IEEE 1588 Precision Time Protocol-Enabled, Three-Port,
10/100 Managed Switch with MII or RMII
Features
Management Capabilities
• The KSZ8463ML/RL/FML/FRL Includes All the
Functions of a 10/100BASE-T/TX/FX Switch System that Combines a Switch Engine, Frame Buffer
Management, Address Look-Up Table, Queue
Management, MIB Counters, Media Access Controllers (MAC) and PHY Transceivers
• Non-Blocking Store-and-Forward Switch Fabric
Ensures Fast Packet Delivery by Utilizing 1024
Entry Forwarding Table
• Port Mirroring/Monitoring/Sniffing: Ingress and/or
Egress Traffic to any Port
• MIB Counters for Fully Compliant Statistics Gathering: 34 Counters per Port
• Loopback Modes for Remote Failure Diagnostics
• Rapid Spanning Tree Protocol Support (RSTP) for
Topology Management and Ring/Linear Recovery
• Bypass Mode Ensures Continuity Even When a
Host is Disabled or Fails
Robust PHY Ports
• Two Integrated IEEE 802.3/802.3u-Compliant
Ethernet Transceivers Supporting 10BASE-T and
100BASE-TX
• Copper and 100BASE-FX Fiber Mode Support in
the KSZ8463FML and KSZ8463FRL
• Copper Mode Support in the KSZ8463ML and
KSZ8463RL
• On-Chip Termination Resistors and Internal Biasing for Differential Pairs to Reduce Power
• HP Auto MDI/MDI-X Crossover Support Eliminates the Need to Differentiate Between Straight
or Crossover Cables in Applications
MAC Ports
•
•
•
•
Three Internal Media Access Control (MAC) Units
MII or RMII Interface Support on MAC Port 3
2Kbyte Jumbo Packet Support
Tail Tagging Mode (One byte Added before FCS)
Support at Port 3 to Inform The Processor Which
Ingress Port Receives the Packet and its Priority
• Supports Reduced Media Independent Interface
(RMII) with 50 MHz Reference Clock Input or Output
• Supports Media Independent Interface (MII) in
Either PHY Mode or MAC Mode on Port 3
• Programmable MAC Addresses for Port 1 and
2018 Microchip Technology Inc.
•
•
•
•
Port 2 and Source Address Filtering for Implementing Ring Topologies
MAC Filtering Function to Filter or Forward
Unknown Unicast Packets
Port 1 and Port 2 MACs Programmable as Either
E2E or P2P Transparent Clock (TC) Ports for
1588 Support
Port 3 MAC Programmable as Slave or Master of
Ordinary Clock (OC) Port for 1588 Support
Microchip LinkMD® Cable Diagnostic Capabilities
for Determining Cable Opens, Shorts, and Length
Advanced Switch Capabilities
• Non-Blocking Store-and-Forward Switch Fabric
Ensures Fast Packet Delivery by Utilizing 1024
Entry Forwarding Table
• IEEE 802.1Q VLAN for Up to 16 Groups with Full
Range of VLAN IDs
• IEEE 802.1p/Q Tag Insertion or Removal on a per
Port Basis (Egress) and Support Double-Tagging
• VLAN ID Tag/Untag Options on per Port Basis
• Fully Compliant with IEEE 802.3/802.3u Standards
• IEEE 802.3x Full-Duplex with Force-Mode Option
and Half-Duplex Backpressure Collision Flow
Control
• IEEE 802.1w Rapid Spanning Tree Protocol Support
• IGMP v1/v2/v3 Snooping for Multicast Packet Filtering
• QoS/CoS Packets Prioritization Support: 802.1p,
DiffServ-Based and Re-Mapping of 802.1p Priority Field per Port Basis on Four Priority Levels
• IPv4/IPv6 QoS Support
• IPv6 Multicast Listener Discovery (MLD) Snooping Support
• Programmable Rate Limiting at the Ingress and
Egress Ports
• Broadcast Storm Protection
• Bypass Mode to Sustain the Switch Function
between Port 1 and Port 2 when CPU (Port 3)
Goes into Sleep Mode
• 1K Entry Forwarding Table with 32K Frame Buffer
• Four Priority Queues with Dynamic Packet Mapping for IEEE 802.1p, IPv4 TOS (DIFFSERV),
IPv6 Traffic Class, etc.
DS00002642A-page 1
KSZ8463ML/RL/FML/FRL
Comprehensive Configuration Registers Access
• High-Speed SPI (4-Wire, Up to 50 MHz) Interface
to Access All Internal Registers
• MII Management (MIIM, MDC/MDIO 2-Wire)
Interface to Access All PHY Registers per Clause
22.2.4.5 of the IEEE 802.3 Specification
• I/O Pin Strapping Facility to Set Certain Register
Bits from I/O Pins at Reset Time
• Control Registers Configurable On-the-Fly
IEEE 1588v2 PTP and Clock Synchronization
• Fully Compliant with the IEEE 1588v2 Precision
Time Protocol
• One-Step or Two-Step Transparent Clock (TC)
Timing Corrections
• E2E (End-to-End) or P2P (Peer-to-Peer) Transparent Clock (TC)
• Grandmaster, Master, Slave, Ordinary Clock (OC)
Support
• IEEE1588v2 PTP Multicast and Unicast Frame
Support
• Transports of PTP Over IPv4/IPv6 UDP and IEEE
802.3 Ethernet
• Delay Request-Response and Peer Delay Mechanism
• Ingress/Egress Packet time stamp Capture/
Recording and Checksum Update
• Correction Field Update with Residence Time and
Link Delay
• IEEE1588v2 PTP Packet Filtering Unit to Reduce
Host Processor Overhead
• A 64-bit Adjustable System Precision Clock
• Twelve Trigger Output Units and Twelve time
stamp Input Units Available for Flexible
IEEE1588v2 Control of Twelve Programmable
GPIO[11:0] Pins Synchronized to the Precision
Time Clock
• GPIO Pin Usage for 1 PPS Generation, Frequency Generator, Control Bit Streams, Event
Monitoring, Precision Pulse Generation, Complex
Waveform Generation
• Energy Detect Power-Down (EDPD), which Disables the PHY Transceiver when Cables are
Removed
• Dynamic Clock Tree Control to Reduce Clocking
in Areas Not in Use
• Power Consumption Less than 0.5W
Additional Features
• Single 25 MHz ±50 ppm Reference Clock
Requirement for MII Mode
• Selectable 25 MHz or 50 MHz Inputs for RMII
Mode
• Comprehensive Programmable Two LED Indicators Support for Link, Activity, Full-/Half-Duplex
and 10/100 Speed
• LED Pins Directly Controllable
• Industrial Temperature Range: –40°C to +85°C
• 64-Pin (10 mm x 10 mm) Lead Free (ROHS)
LQFP Package
Applications
• Industrial Ethernet Applications that Employ IEEE
802.3-Compliant MACs. (Ethernet/IP, Profinet,
MODBUS TCP, etc)
• Real-Time Ethernet Networks Requiring SubMicrosecond Synchronization over Standard
Ethernet
• IEC 61850 Networks Supporting Power Substation Automation
• Networked Measurement and Control Systems
• Industrial Automation and Motion Control Systems
• Test and Measurement Equipment
Power and Power Management
• Single 3.3V Power Supply with Optional VDD I/O
for 1.8V, 2.5V, or 3.3V
• Integrated Low Voltage (~1.3V) Low-Noise Regulator (LDO) Output for Digital and Analog Core
Power
• Supports IEEE P802.3az™ Energy Efficient
Ethernet (EEE) to Reduce Power Consumption in
Transceivers in LPI State
• Full-Chip Hardware or Software Power-Down (All
Registers Value are Not Saved and Strap-In Value
will Re-Strap After Release the Power-Down)
DS00002642A-page 2
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at docerrors@microchip.com. We welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000000A is version A of document DS30000000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the
revision of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
• Microchip’s Worldwide Web site; http://www.microchip.com
• Your local Microchip sales office (see last page)
When contacting a sales office, please specify which device, revision of silicon and data sheet (include -literature number) you are
using.
Customer Notification System
Register on our web site at www.microchip.com to receive the most current information on all of our products.
2018 Microchip Technology Inc.
DS00002642A-page 3
KSZ8463ML/RL/FML/FRL
Table of Contents
1.0 Introduction ..................................................................................................................................................................................... 5
2.0 Pin Description and Configuration ................................................................................................................................................... 9
3.0 Functional Description ................................................................................................................................................................... 17
4.0 Register Descriptions .................................................................................................................................................................... 59
5.0 Operational Characteristics ......................................................................................................................................................... 189
6.0 Electrical Characteristics ............................................................................................................................................................. 190
7.0 Timing Specifications .................................................................................................................................................................. 193
8.0 Reference Clock: Connection and Selection ............................................................................................................................... 205
9.0 Selection of Isolation Transformers ............................................................................................................................................. 206
10.0 Package Outline ........................................................................................................................................................................ 207
Appendix A: Data Sheet Revision History ......................................................................................................................................... 208
The Microchip Web Site .................................................................................................................................................................... 209
Customer Change Notification Service ............................................................................................................................................. 209
Customer Support ............................................................................................................................................................................. 209
Product Identification System ............................................................................................................................................................ 210
DS00002642A-page 4
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
1.0
INTRODUCTION
1.1
General Terms and Conditions
The following is list of the general terms used throughout this document:
BIU - Bus Interface Unit
The host interface function that performs code conversion, buffering,
and the like required for communications to and from a network.
BPDU - Bridge Protocol Data Unit
A packet containing ports, addresses, etc. to make sure data being
passed through a bridged network arrives at its proper destination.
CMOS - Complementary Metal Oxide
Semiconductor
A common semiconductor manufacturing technique in which positive
and negative types of transistors are combined to form a current gate
that in turn forms an effective means of controlling electrical current
through a chip.
CRC - Cyclic Redundancy Check
A common technique for detecting data transmission errors. CRC for
Ethernet is 32 bits long.
Cut-Through Switch
A switch typically processes received packets by reading in the full
packet (storing), then processing the packet to determine where it
needs to go, then forwarding it. A cut-through switch simply reads in
the first bit of an incoming packet and forwards the packet. Cutthrough switches do not store the packet.
DA - Destination Address
The address to send packets.
EMI - Electro-Magnetic Interference
A naturally occurring phenomena when the electromagnetic field of
one device disrupts, impedes or degrades the electromagnetic field
of another device by coming into proximity with it. In computer technology, computer devices are susceptible to EMI because electromagnetic fields are a byproduct of passing electricity through a wire.
Data lines that have not been properly shielded are susceptible to
data corruption by EMI.
FCS - Frame Check Sequence
See CRC.
FID - Frame or Filter ID
Specifies the frame identifier. Alternately is the filter identifier.
GPIO - General Purpose Input/Output
General Purpose Input/Output pins are signal pins that can be controlled or monitored by hardware and software to perform specific
tasks.
IGMP - Internet Group Management
Protocol
The protocol defined by RFC 1112 for IP multicast transmissions.
IPG - Inter-Packet Gap
A time delay between successive data packets mandated by the network standard for protocol reasons. In Ethernet, the medium has to
be "silent" (i.e., no data transfer) for a short period of time before a
node can consider the network idle and start to transmit. IPG is used
to correct timing differences between a transmitter and receiver.
During the IPG, no data is transferred, and information in the gap can
be discarded or additions inserted without impact on data integrity.
ISA - Industry Standard Architecture
A bus architecture used in the IBM PC/XT and PC/AT.
ISI - Inter-Symbol Interference
The disruption of transmitted code caused by adjacent pulses affecting or interfering with each other.
Jumbo Packet
A packet larger than the standard Ethernet packet (1500 bytes).
Large packet sizes allow for more efficient use of bandwidth, lower
overhead, less processing, etc.
MAC - Media Access Controller
A functional block responsible for implementing the media access
control layer which is a sub layer of the data link layer.
MDI - Medium Dependent Interface
An Ethernet port connection that allows network hubs or switches to
connect to other hubs or switches without a null-modem, or crossover, cable. MDI provides the standard interface to a particular media
(copper or fiber) and is therefore “media dependent”.
2018 Microchip Technology Inc.
DS00002642A-page 5
KSZ8463ML/RL/FML/FRL
BIU - Bus Interface Unit
The host interface function that performs code conversion, buffering,
and the like required for communications to and from a network.
MDI-X - Medium Dependent Interface
Crossover
An Ethernet port connection that allows networked end stations (i.e.,
PCs or workstations) to connect to each other using a null-modem, or
crossover, cable. For 10/100 full-duplex networks, an end point (such
as a computer) and a switch are wired so that each transmitter connects to the far end receiver. When connecting two computers
together, a cable that crosses the TX and RX is required to do this.
With auto MDI-X, the PHY senses the correct TX and RX roles, eliminating any cable confusion.
MIB - Management Information Base
The MIB comprises the management portion of network devices.
This can include things like monitoring traffic levels and faults (statistical), and can also change operating parameters in network nodes
(static forwarding addresses).
MII - Media Independent Interface
The MII accesses PHY registers as defined in the IEEE 802.3 specification.
NIC - Network Interface Card
An expansion board inserted into a computer to allow it to be connected to a network. Most NICs are designed for a particular type of
network, protocol, and media, although some can serve multiple networks.
NPVID - Non-Port VLAN ID
The port VLAN ID value is used as a VLAN reference.
NRZ - Non-Return to Zero
A type of signal data encoding whereby the signal does not return to
a zero state in between bits.
PHY
A device or functional block which performs the physical layer interface function in a network.
PLL - Phase-Locked Loop
An electronic circuit that controls an oscillator so that it maintains a
constant phase angle (i.e., lock) on the frequency of an input, or reference, signal. A PLL ensures that a communication signal is locked
on a specific frequency and can also be used to generate, modulate,
and demodulate a signal and divide a frequency.
PTP - Precision Time Protocol
A protocol, IEEE 1588 as applied to this device, for synchronizing the
clocks of devices attached to a specific network.
SA - Source Address
The address from which information has been sent.
TDR - Time Domain Reflectometry
TDR is used to pinpoint flaws and problems in underground and
aerial wire, cabling, and fiber optics. They send a signal down the
conductor and measure the time it takes for the signal, or part of the
signal, to return.
TSU - time stamp Input Unit
The functional block which captures signals on the GPIO pins and
assigns a time to the specific event.
TOU - Trigger Output Unit
The functional block which generates user configured waveforms on
a specified GPIO pin at a specific trigger time.
UTP - Unshielded Twisted Pair
Commonly a cable containing four twisted pairs of wires. The wires
are twisted in such a manner as to cancel electrical interference generated in each wire, therefore shielding is not required.
VLAN - Virtual Local Area Network
A configuration of computers that acts as if all computers are connected by the same physical network but which may be located virtually anywhere.
DS00002642A-page 6
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
1.2
General Description
The KSZ8463 EtherSynch® product line consists of IEEE 1588v2 enabled Ethernet switches, providing integrated communications and synchronization for a range of Industrial Ethernet applications.
The KSZ8463 EtherSynch product line enables distributed, daisy-chained or ring topologies preferred for Industrial
Ethernet networks. Conventional centralized (i.e., star-wired) topologies are also supported for dual-homed, fault-tolerant arrangements.
A flexible set of standard MAC interfaces is provided to interface to external host processors with embedded Ethernet
MACs:
•
•
•
•
KSZ8463ML: Media Independent Interface (MII)
KSZ8463RL: Reduced Media Independent Interface (RMII)
KSZ8463FML: MII, supports 100BASE-FX fiber in addition to 10/100BASE-TX copper
KSZ8463FRL: RMII, supports 100BASE-FX fiber in addition to 10/100BASE-TX copper
The KSZ8463 devices incorporate the IEEE 1588v2 protocol. Sub-microsecond synchronization is available via the use
of hardware-based time-stamping and transparent clocks making it the ideal solution for time synchronized Layer 2 communication in critical industrial applications.
Extensive general purpose I/O (GPIO) capabilities are available to use with the IEEE 1588v2 PTP to efficiently and
accurately interface to locally connected devices.
Complementing the industry’s most-integrated IEEE 1588v2 device is a precision timing protocol (PTP) v2 software
stack that has been pre-qualified with the KSZ84xx product family. The PTP stack has been optimized around the
KSZ84xx chip architecture, and is available in source code format along with Microchip’s chip driver.
The KSZ8463 product line is built upon Microchip’s industry-leading Ethernet technology, with features designed to offload host processing and streamline your overall design.
•
•
•
•
Wire-speed Ethernet switching fabric with extensive filtering
Two integrated 10/100BASE-TX PHY transceivers, featuring the industry’s lowest power consumption
Full-featured quality-of-service (QoS) support
Flexible management options that support common standard interfaces
The wire-speed, store-and-forward switching fabric provides a full complement of QoS and congestion control features
optimized for real-time Ethernet.
A robust assortment of power-management features including Energy Efficient Ethernet (EEE) have been designed in
to satisfy energy efficient environments.
2018 Microchip Technology Inc.
DS00002642A-page 7
KSZ8463ML/RL/FML/FRL
FIGURE 1-1:
SYSTEM BLOCK DIAGRAM, KSZ8463ML/RL/FML/FRL
FRAME
BUFFERS
MIB
COUNTERS
BUFFER
MANAGEMENT
QUEUE
MANAGEMENT
1024
ADDRESSES
LOOK-UP
TABLE
SWITCH ENGINE
VLAN TAGGING, QoS PRIORITY, FIFO, FLOW CONTROL
IEEE 1588 PTP PACKET FILTERING AND PROCESSING
MII/RMII
(PORT 3)
SERIAL PORT
INTERFACE
SPI OR MIIM
SERIAL PORT
X1
X2
IEEE 1588
ENABLED
10/100 MAC3
PLL
CLOCK
(TO 1588 TIME
STAMP BLOCKS)
I/O REGISTERS
CONTROL/STATUS
12 EVENT TRIGGER UNITS
AND 12 TIMESTAMP UNITS
IEEE 1588
SYNCHRONIZED
CLOCK
IEEE 1588 TIME
STAMP FOR PORT 1
IEEE 1588
ENABLED
10/100
MAC 1
IEEE 1588
ENABLED
10/100
MAC 2
10/100 BASE
T/TX/FX
PHY 1
10/100 BASE
T/TX/FX
PHY 2
PORT 1
TX/RX±
(AUTO MDI/MDI-X)
PORT 2
TX/RX±
IEEE 1588 TIME
STAMP FOR PORT 2
LINK MD AND
ENERGY EFFICIENT
ETHERNET CONTROL
GPIOs
VDD_IO
1.3V LOW-NOISE
REGULATOR
VDD_L
DS00002642A-page 8
STRAP-IN
CONFIGURATION
P1LED[1:0]
LEDs
DRIVER
P2LED[1:0]
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
2.0
PIN DESCRIPTION AND CONFIGURATION
64-PIN LQFP ASSIGNMENT, (TOP VIEW)
FXSD1
RSTN
P2LED0/GPIO10_MLI
PSLED1/GPIO9_MLI
P1LED0
P1LED1/GPIO7_MLI
GPIO6
DGND
VDD_IO
GPIO5
GPIO4
GPIO3
GPIO2
VDD_L
DGND
GPIO1
FIGURE 2-1:
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
KSZ8463ML/RL/FML/FRL
(TOP VIEW)
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
GPIO0
GPIO11
GPIO8
SPI_DI/MDIO
SPI_SCLK/MDC
INTRN
SPI_CSN
SPI_DO
VDD_L
DGND
RX_CLK/GPIO7_RL1
COL/GPIO10_RL1
CRS/GPIO9_RLI
RXD0
RXD1
RXD2
PWRDN
X1
X2
DGNG
VDD_IO
TXEN
TXD3/EN_REFCLKO
TXD2/NC
TXD1
TXD0
TX_CLK/REFCLK_I
TX_ER/MII_BP
DGND
VDD_IO
RX_DV
RXD3/REFCLK_O
RXM1
RXP1
AGND
TXM1
TXP1
VDD_AL
ISET
AGND
VDD_A3.3
RXM2
RXP2
AGND
TXM2
TXP2
FXSD2
VDD_COL
2018 Microchip Technology Inc.
DS00002642A-page 9
KSZ8463ML/RL/FML/FRL
TABLE 2-1:
SIGNALS FOR KSZ8463ML/RL/FML/FRL
Pin
Number
Pin Name
Type
(Note
2-1)
1
RXM1
I/O
Port 1 physical receive (MDI) or transmit (MDIX) signal (– differential).
2
RXP1
I/O
Port 1 physical receive (MDI) or transmit (MDIX) signal (+ differential).
3
AGND
GND
4
TXM1
I/O
Port 1 physical transmit (MDI) or receive (MDIX) signal (– differential).
5
TXP1
I/O
Port 1 physical transmit (MDI) or receive (MDIX) signal (+ differential).
6
VDD_AL
P
This pin is used as an input for the low-voltage analog power. Its source
should have appropriate filtering with a ferrite bead and capacitors.
7
ISET
O
Set physical transmits output current.
Pull-down this pin with a 6.49 kΩ (1%) resistor to ground.
8
AGND
GND
9
VDD_A3.3
P
10
RXM2
I/O
Port 2 physical receive (MDI) or transmit (MDIX) signal (– differential).
11
RXP2
I/O
Port 2 physical receive (MDI) or transmit (MDIX) signal (+ differential).
12
AGND
GND
13
TXM2
I/O
Port 2 physical transmit (MDI) or receive (MDIX) signal (– differential).
14
TXP2
I/O
Port 2 physical transmit (MDI) or receive (MDIX) signal (+ differential).
15
FXSD2
I
Fiber signal detect input for port 2 in 100BASE-FX fiber mode. When in copper mode, this input is unused and should be pulled to GND.
Note: This functionality is available only on the KSZ8463FML/FRL devices.
16
VDD_COL
P
This pin is used as a second input for the low-voltage analog power. Its
source should have appropriate filtering with a ferrite bead and capacitors.
17
PWRDN
IPU
18
X1
I
19
X2
O
20
DGND
GND
21
VDD_IO
P
DS00002642A-page 10
Description
Analog Ground.
Analog Ground.
3.3V analog VDD input power supply (Must be well decoupled).
Analog Ground.
Full-Chip Power-Down
Active-Low (Low = Power-down; High or floating = Normal operation).
While this pin is asserted low, all I/O pins will be tri-stated. All registers will be
set to their default state. While this pin is asserted, power consumption will be
minimal. When the pin is de-asserted, power consumption will climb to nominal and the device will be in the same state as having been reset by the reset
pin (RSTN, pin 63).
25 MHz Crystal or Oscillator Clock Connection
Pins (X1, X2) connect to a crystal. If an oscillator is used, X1 connects to a
VDD_IO voltage tolerant oscillator and X2 is a no connect. This clock requirement is ±50 ppm.
The KSZ8463RL has the option to use REFCLK_I (50 MHz) as its primary
clock input instead of X1 and X2. This is determined by the state of pin 41
(SPI_DO) at power-up/reset time. See Table 2-2 for details. (Applies to the
KSZ8463RL/FRL devices only)
Digital ground.
3.3V, 2.5V, or 1.8V digital VDD input power pin for IO logic and the internal
low-voltage regulator.
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 2-1:
Pin
Number
22
23
24
25
26
27
SIGNALS FOR KSZ8463ML/RL/FML/FRL (CONTINUED)
Pin Name
Type
(Note
2-1)
TX_EN
TXD3/
EN_REFCLKO
TXD2/NC
TXD1
TXD0
TX_CLK/
REFCLK_I
Description
IPD
(8463ML, 8463FML) – MII Mode:
Transmit Enable. Active high input indicates there is valid transmit data on
TXD[3:0].
(8463RL, 8463FRL) – RMII Mode:
Transmit Enable. Active high indicates there is valid transmit data on
TXD[1:0].
IPD
(8463ML, 8463FML) – MII Mode:
Transmit data input bit[3]. This data is synchronous to the TX_CLK (2.5 MHz
in 10BASE-T mode or 25 MHz in 100BASE-TX mode)
(8463RL, 8463FRL) – RMII Mode:
EN_REFCLKO is used to enable REFCLK_O output on pin 32. If pulled up,
the REFCLK_O output is enabled. If pulled down to disable, the REFCLK_O
output is disabled.
IPD
(8463ML, 8463FML) – MII Mode:
Transmit data input bit[2]. This data is synchronous to TX_CLK (2.5 MHz in
10BASE-T mode or 25 MHz in 100BASE-TX mode).
(8463RL, 8463FRL) – RMII Mode:
No connect. Is not used.
IPD
(8463ML, 8463FML) – MII Mode:
Transmit data input bit[1]. This data is synchronous to TX_CLK (2.5 MHz in
10BASE-T mode or 25 MHz in 100BASE-TX mode).
(8463RL, 8463FRL) – RMII Mode:
Transmit data input bit[1]. This data is synchronous to REFCLK (50 MHz).
IPD
(8463ML, 8463FML) – MII Mode:
Transmit data input bit[0]. This data is synchronous to TX_CLK (2.5 MHz in
10BASE-T mode or 25 MHz in 100BASE-TX mode).
(8463RL, 8463FRL) – RMII Mode:
Transmit data input bit[0]. This data is synchronous to REFCLK (50 MHz).
I/O
(PD)
(8463ML, 8463FML) – MII Mode:
Transmit clock. This is the output clock in PHY MII mode and input clock in
MAC MII mode (2.5 MHz in 10BASE-T mode or 25 MHz in 100BASE-TX
mode).
(8463RL, 8463FRL) – RMII Mode:
Reference input clock (50 MHz).
28
TX_ER/
MII_BP
IPD
(8463ML, 8463FML) – MII Mode:
Transmit error input in MII MAC mode.
In MII PHY mode:
1 = Disable the MII PHY mode link and enable the bypass mode.
0 = Set MII PHY mode in normal operation.
(8463RL, 8463FRL) – RMII Mode:
No connect. Not used.
29
DGND
GND
Digital Ground.
30
VDD_IO
P
2018 Microchip Technology Inc.
3.3V, 2.5V, or 1.8V digital VDD input power pin for IO logic and the internal
low-voltage regulator.
DS00002642A-page 11
KSZ8463ML/RL/FML/FRL
TABLE 2-1:
Pin
Number
31
32
33
34
35
36
SIGNALS FOR KSZ8463ML/RL/FML/FRL (CONTINUED)
Pin Name
RX_DV
RXD3/
REFCLK_O
RXD2
RXD1
RXD0
CRS/
GPIO9_RLI
DS00002642A-page 12
Type
(Note
2-1)
Description
IPU/O
(8463ML, 8463FML) – MII Mode:
Receive data valid, active high indicates that receive data on RXD[3:0] is
valid.
(8463RL, 8463FRL) – RMII Mode:
Receive data valid, active high indicates that receive data on RXD[1:0] is
valid.
Config Mode:
This pin is pulled up or down and its value is latched during the power-up /
reset to select either PHY MII mode or MAC MII mode. See Table 2-2 for
details.
IPD/O
(8463ML, 8463FML) – MII Mode:
Receive data output bit[3]. This data is synchronous to RX_CLK (2.5 MHz in
10BASE-T mode or 25 MHz in 100BASE-TX mode)
(8463RL, 8463FRL) – RMII Mode:
REFCLK_O (50 MHz) output when EN_REFCLKO (pin 23) is pulled-up.
(16 mA drive)
IPU/O
(8463ML, 8463FML) – MII Mode:
Receive data output bit[2]. This data is synchronous to RX_CLK (2.5 MHz in
10BASE-T mode or 25 MHz in 100BASE-TX mode)
(8463RL, 8463FRL) – RMII Mode:
Not used.
Config Mode:
This pin is pulled up or down via an external resistor and its value is latched
during power-up/reset to select either high-speed SPI or low-speed SPI
mode. See Table 2-2 for details.
IPU/O
(8463ML, 8463FML) – MII Mode:
Receive data output bit[1]. This data is synchronous to RX_CLK (2.5 MHz in
10BASE-T mode or 25 MHz in 100BASE-TX mode)
(8463RL, 8463FRL) – RMII Mode:
Receive data output bit[1]. This data is synchronous to REFCLK (50 MHz).
Config Mode:
This pin is pulled up or down via an external resistor and its value is latched
during power-up/reset to select serial bus mode. See Table 2-2 for details.
IPD/O
(8463ML, 8463FML) – MII Mode:
Receive data output bit[0]. This data is synchronous to RX_CLK (2.5 MHz in
10BASE-T mode or 25 MHz in 100BASE-TX mode)
(8463RL, 8463FRL) – RMII Mode:
Receive data output bit[0]. This data is synchronous to REFCLK (50 MHz).
Config Mode:
This pin is pulled up or down via an external resistor and its value is latched
during power-up/reset to select serial bus mode. See Table 2-2 for details.
I/O
(PD)
(8463ML, 8463FML) – MII Mode:
Carrier Sense. This is an output signal in PHY MII mode and an input signal in
MAC MII mode.
(8463RL, 8463FRL) – RMII Mode:
This is GPIO9 while in RMII mode. (Refer to GPIO0 pin 48 description).
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 2-1:
Pin
Number
37
SIGNALS FOR KSZ8463ML/RL/FML/FRL (CONTINUED)
Pin Name
Type
(Note
2-1)
Description
I/O
(PD)
(8463ML, 8463FML) – MII Mode:
Collision Detect. This is an output signal in PHY MII mode and an input signal
in MAC MII mode.
(8463RL, 8463FRL) – RMII Mode:
This is GPIO10 while in RMII Mode. (Refer to GPIO0 pin 48 description).
COL/
GPIO10_RLI
38
RX_CLK/
GPIO7_RLI
I/O
(PD)
(8463ML, 8463FML) – MII Mode:
Receive Clock. This is an output clock in PHY MII mode and an input clock in
MAC MII mode (2.5 MHz in 10BASE-T mode or 25 MHz in 100BASE-TX
mode).
(8463RL, 8463FRL) – RMII Mode:
This is GPIO7 while in RMII mode. (Refer to GPIO0 pin 48 description).
39
DGND
GND
Digital Ground
40
VDD_L
P
This pin can be used in two ways: as the pin to input a low voltage to the
device if the internal low-voltage regulator is not used, or as the low-voltage
output if the internal low-voltage regulator is used.
IPU/O
Serial Data Output in SPI Slave Mode.
Config Mode:
This pin pull-up/pull-down value is latched to select clock input either 25 MHz
from X1/X2 or 50 MHz from REFCLK_I during power-up/reset. See Strapping
Options section for detail.
The REFCLK_I (50 MHz) option is available only on the KSZ8463RL and
KSZ8463FRL. For the KSZ8463ML and KSZ8463FML, this pin must NOT be
pulled down at power-up/reset.
41
SPI_DO
42
SPI_CSN
IPD
Chip Select (active-low) in SPI Slave Mode.
When SPI_CSN is high, the device is deselected and SPI_DO is held in a
high-impedance state. A high-to-low transition is used to initiate the SPI data
transfer.
Note: An external 4.7 kΩ pull-up is needed on this pin when it is in use.
43
INTRN
OPU
Interrupt Output.
This is an active-low signal going to the host CPU to indicate an interrupt status bit is set. This pin needs an external 4.7 kΩ pull-up resistor.
44
SPI_SCLK/
MDC
IPU
Serial Clock input in SPI (SPI_SCLK) slave mode.
MIIM (MDC) mode is clock input.
45
SPI_DI/
MDIO
I/O
(PU)
Serial Data Input in SPI (SPI_DI) Slave Mode.
Serial Data input/output in MIIM (MDIO) mode.
This pin needs an external 4.7 kΩ pull-up resistor.
46
GPIO8
I/O
(PD)
This pin is GPIO8 (refer to GPIO0 pin 48 description).
47
GPIO11
I/O
(PU)
This pin is GPIO11 (refer to GPIO0 pin 48 description).
GPIO0
I/O
(PU)
General Purpose Input/Output [0]
This pin can be used as an input or output pin for use by the IEEE 1588 event
trigger or time stamp capture units. It will be synchronized to the internal IEEE
1588 clock. The host processor can also directly drive or read this GPIO pin.
48
2018 Microchip Technology Inc.
DS00002642A-page 13
KSZ8463ML/RL/FML/FRL
TABLE 2-1:
SIGNALS FOR KSZ8463ML/RL/FML/FRL (CONTINUED)
Pin
Number
Pin Name
Type
(Note
2-1)
49
GPIO1
I/O
(PU)
This pin is GPIO1 (refer to GPIO0 pin 48 description).
50
DGND
GND
Digital Ground.
51
VDD_L
P
52
GPIO2
I/O
(PU)
This pin is GPIO2 (refer to GPIO0 pin 48 description).
53
GPIO3
I/O
(PD)
This pin is GPIO3 (refer to GPIO0 pin 48 description).
54
GPIO4
I/O
(PD)
This pin is GPIO4 (refer to GPIO0 pin 48 description).
55
GPIO5
I/O
(PD)
This pin is GPIO5 (refer to GPIO0 pin 48 description).
56
VDD_IO
P
57
DGND
GND
Digital ground.
58
GPIO6
I/O
(PU)
This pin is GPIO6 (refer to GPIO0 pin 48 description).
DS00002642A-page 14
Description
This pin can be used in two ways: as the pin to input a low voltage to the
device if the internal low-voltage regulator is not used, or as the low-voltage
output if the internal low-voltage regulator is used.
3.3V, 2.5V, or 1.8V digital VDD input power pin for IO logic and the internal
low-voltage regulator.
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 2-1:
Pin
Number
59
SIGNALS FOR KSZ8463ML/RL/FML/FRL (CONTINUED)
Pin Name
Type
(Note
2-1)
P1LED1/
GPIO7_MLI
I/O
(PU)
Description
Programmable LED Output to Indicate Port 1 and Port 2 Activity/Status.
The LED is ON (active) when output is low; the LED is OFF (inactive) when
output is high.
The port 1 LED pins outputs are determined by the table below if Reg. 0x06C
– 0x06D, bits [14:12] are set to ‘000’. Otherwise, the port 1 LED pins are controlled via the processor by setting Reg. 0x06C – 0x06D, bits [14:12] to a nonzero value.
The port 2 LED pins outputs are determined by the table below if Reg. 0x084
– 0x085, bits [14:12] are set to ‘000’. Otherwise, the port 2 LED pins are controlled via the processor by setting Reg. 0x084 – 0x085, bits [14:12] to a nonzero value.
Automatic port 1 and port 2 indicators are defined as follows:
Two bits [9:8] in SGCR7 Control Register
60
61
P1LED0
P2LED1/
GPIO9_MLI
I/O
(PU)
I/O
(PU)
—
00
(default)
01
10
11
P1LED1/P2LED1
Speed
ACT
Duplex
Duplex
P1LED0/P2LED0
Link/ACT
Link
Link/ACT
Link
Link = LED ON; ACT = LED Blink; Link/ACT = LED ON/Blink
Speed = LED ON (100BASE-TX); LED OFF (10BASE-T)
Duplex = LED ON (Full-Duplex); LED OFF (Half-Duplex)
(8463ML, 8463FML) – MII Mode:
Functionality is controlled by IOMXSEL register D6h.
Pin 59 is P1LED1 (default) or GPIO7.
Pin 60 is P1LED0.
Pin 61 is P2LED1 (default) or GPIO9.
Pin 62 is P2LED0 (default) or GPIO10.
(8463RL, 8463FRL) – RMII Mode:
Pin 59 is P1LED1.
Pin 60 is P1LED0.
Pin 61 is P2LED1.
Pin 62 is P2LED0.
62
P2LED0/
GPIO10_MLI
I/O
(PU)
63
RSTN
IPU
Hardware reset input (active-low). This reset input is required to be low for a
minimum of 10 ms after supply voltages VDD_IO and 3.3V are stable.
64
FXSD1
I
Fiber Signal Detect input for port 1 in 100BASE-FX fiber mode. When in copper mode, this input is unused and should be pulled to GND.
Note: This functionality is available only on the KSZ8463FML/FRL devices.
Note 2-1
P = power supply; GND = ground
I = input; O = output; I/O = bi-directional
IPU/O = Input with internal pull-up (58 kΩ ±30%) during power-up/reset; output pin otherwise.
IPD/O = Input with internal pull-down (58 kΩ ±30%) during power-up/reset; output pin otherwise.
IPU = Input with internal pull-up. (58 kΩ ±30%)
IPD = Input with internal pull-down. (58 kΩ ±30%)
OPU = Output with internal pull-up. (58 kΩ ±30%)
OPD = Output with internal pull-down. (58 kΩ ±30%)
I/O (PD) = Bi-directional input/output with internal pull-down. (58 kΩ ±30%)
I/O (PU) = Bi-directional input/output with internal pull-up. (58 kΩ ±30%)
2018 Microchip Technology Inc.
DS00002642A-page 15
KSZ8463ML/RL/FML/FRL
TABLE 2-2:
Pin
Number
STRAPPING OPTIONS
Pin Name
Type
Note 2-1
Description
31
RX_DV
IPU/O
PHY Mode or MAC Mode Select During Power-Up/Reset:
Pull-up (default) or No Connect = PHY MII mode.
Pull-down = MAC MII mode.
Note: There is no equivalent strapping pin for RMII mode.
33
RXD2
IPU/O
High-Speed SPI or Low-Speed SPI Select During Power-Up/Reset:
Pull-up (default) or No Connect = High-speed SPI mode (up to 50 MHz).
Pull-down = Low-speed SPI mode (up to 12.5 MHz).
IPU/O
Serial Bus Mode Selection to Access the KSZ8463 Internal Registers
During Power-Up/Reset:
Note: SPI Slave Mode is required for access to all registers, and for implementing the IEEE1588 protocol.
[RXD1, RXD0] = [0, 0] — Reserved
[RXD1, RXD0] = [0, 1] — Reserved
[RXD1, RXD0] = [1, 0] — SPI Slave Mode (Default)
34
35
RXD1
RXD0
IPD/O
Interface Signals
Type
Description
SPI_DO (pin 41)
O
SPI data out
SPI_SCLK (pin 44)
I
SPI clock
SPI_DI (pin 45)
I
SPI data in
SPI_CSN (pin 42)
I
SPI chip select
[RXD1, RXD0] = [1, 1] – MIIM-Mode
In MIIM mode, the KSZ8463 provides access to its 16-bit MIIM registers
through its MDC (pin 44) and MDIO (pin 45).
41
Note 2-1
25 MHz/50 MHz Input Clock Select for X1/X2 REFCLK_I On Power-Up/
Reset:
Pull-up (default) or No Connect = 25 MHz input from X1/X2. (Both RMII and
MII mode)
SPI_DO
IPU/O
Pull-down = 50 MHz input from REFCLK_I (EN_REFCLK = “0”). (Only RMII
mode) This option is available only on the KSZ8463RL and KSZ8463FRL.
For the KSZ8463ML and KSZ8463FML, this pin must NOT be pulled down
at power-up/reset time.
IPU/O = Input with internal pull-up (58 kΩ ±30%) during power-up/reset; output pin otherwise.
IPD/O = Input with internal pull-down (58 kΩ ±30%) during power-up/reset; output pin otherwise.
All strapping pins are latched at the end of the power-up or reset cycle. They are also latched when powering-up from
a hardware or software power-down or hardware reset state.
DS00002642A-page 16
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
3.0
FUNCTIONAL DESCRIPTION
The KSZ8463 is a highly-integrated networking device that incorporates a Layer-2 switch, two 10BASE-T/100BASE-TX
physical layer transceivers (PHYs) and associated MAC units, one MII/RMII interface on a third accessible MAC unit,
and contains key IEEE 1588 precision time protocol (PTP) features.
The KSZ8463 operates in a managed mode. In managed mode, a host processor can access and control all PHY,
Switch, MAC, and IEEE 1588 related registers in the KSZ8463 via the high-speed SPI bus, or partial control via the MIIM
(MDC/MDIO) interface.
Physical signal transmission and reception are enhanced through the use of analog circuits in the PHY that make the
design more efficient and allow for low power consumption. Both power management and Energy Efficient Ethernet
(EEE) are designed to save more power while the device is in idle state.
The KSZ8463 is fully compliant to IEEE802.3u standards.
3.1
3.1.1
Physical (PHY) Block
100BASE-TX TRANSMIT
The 100BASE-TX transmit function performs parallel-to-serial conversion, 4B/5B coding, scrambling, NRZ-to-NRZI conversion, and MLT3 encoding and transmission.
The circuitry starts with a parallel-to-serial conversion, which converts the MII data from the MAC into a 125 MHz serial
bit stream. The data and control stream is then converted into 4B/5B coding, followed by a scrambler. The serialized
data is further converted from NRZ-to-NRZI format, and then transmitted in MLT3 current output. An external 6.49 kΩ
(1%) resistor for the 1:1 transformer ratio sets the output current.
The output signal has a typical rise/fall time of 4 ns and complies with the ANSI TP-PMD standard regarding amplitude
balance, overshoot, and timing jitter. The wave-shaped 10BASE-T output driver is also incorporated into the 100BASETX driver.
3.1.2
100BASE-TX RECEIVE
The 100BASE-TX receiver function performs adaptive equalization, DC restoration, MLT3-to-NRZI conversion, data and
clock recovery, NRZI-to-NRZ conversion, de-scrambling, 4B/5B decoding, and serial-to-parallel conversion.
The receiving side starts with the equalization filter to compensate for inter-symbol interference (ISI) over the twisted
pair cable. Since the amplitude loss and phase distortion is a function of the cable length, the equalizer has to adjust its
characteristics to optimize performance. In this design, the variable equalizer makes an initial estimation based on comparisons of incoming signal strength against some known cable characteristics, and then tunes itself for optimization.
This is an ongoing process and self-adjusts against environmental changes such as temperature variations.
Next, the equalized signal goes through a DC restoration and data conversion block. The DC restoration circuit is used
to compensate for the effect of baseline wander and to improve the dynamic range. The differential data conversion
circuit converts the MLT3 format back to NRZI. The slicing threshold is also adaptive.
The clock recovery circuit extracts the 125 MHz clock from the edges of the NRZI signal. This recovered clock is then
used to convert the NRZI signal into the NRZ format. This signal is sent through the de-scrambler followed by the 4B/
5B decoder. Finally, the NRZ serial data is converted to an MII format and provided as the input data to the MAC.
3.1.3
SCRAMBLER/DE-SCRAMBLER (100BASE-TX ONLY)
The purpose of the scrambler is to spread the power spectrum of the signal to reduce electromagnetic interference (EMI)
and baseline wander.
Transmitted data is scrambled through the use of an 11-bit wide linear feedback shift register (LFSR). The scrambler
generates a 2047-bit non-repetitive sequence. Then the receiver de-scrambles the incoming data stream using the
same sequence as at the transmitter.
3.1.4
PLL CLOCK SYNTHESIZER (RECOVERY)
The device incorporates an internal PLL clock synthesizer for data recovery as well as for generating various clocks
used in the device. Refer to the Device Clocks section for details of this area.
3.1.5
100BASE-FX OPERATION
Fiber Mode is available only on the KSZ8463FML and KSZ8463FRL devices.
2018 Microchip Technology Inc.
DS00002642A-page 17
KSZ8463ML/RL/FML/FRL
100BASE-FX operation is similar to 100BASE-TX operation except that the scrambler/de-scrambler and MLT3 encoder/
decoder are bypassed on transmission and reception. In this fiber mode, the auto-negotiation feature is bypassed and
auto MDI/MDIX is disabled since there is no standard that supports fiber auto-negotiation and auto MDI/MDIX mode.
The fiber port must be forced to either full-duplex or half-duplex mode.
All KSZ8463 devices are in copper mode (10BASE-T/100BASE-TX) when reset or powered on. Fiber mode is enabled
by clearing bits [7:6] in the CFGR register (0x0D8-0x0D9). Each port is individually configurable. Bit[13] in the DSP_CNTRL_6 register (0x734-0x735) should also be cleared if either (or both) ports are set to fiber mode.
3.1.6
100BASE-FX SIGNAL DETECTION
In 100BASE-FX operation, the fiber signal detect inputs FXSD1 and FXSD2 are usually connected to the signal detect
(SD) output pin of the fiber transceiver. When FXSD is low, no fiber signal is detected and a far-end fault (FEF) is generated. When FXSD is high, the fiber signal is detected. To ensure proper operation, a resistive voltage divider is recommended to adjust the fiber transceiver SD output voltage swing to match the FXSD pin’s input voltage threshold.
Alternatively, the user may choose not to implement the FEF feature. In this case, the FXSD input pin is tied high to
force 100BASE-FX mode.
In copper mode, and on the KSZ8463ML and KSZ8463RL, the FXSD pins are unused and should be pulled low.
3.1.7
100BASE-FX FAR-END FAULT
A Far-End Fault (FEF) occurs when the signal detection is logically false on the receive side of the fiber transceiver. The
KSZ8463FML/FRL detects an FEF when its FXSD input is below the fiber signal detect threshold. When an FEF is
detected, the KSZ8463FML/FRL signals its fiber link partner that a FEF has occurred by sending 84 1’s followed by a
zero in the idle period between frames. By default, FEF is enabled. FEF can be disabled through register setting in
P1CR4[12] and P2CR4[12].
3.1.8
10BASE-T TRANSMIT
The 10BASE-T driver is incorporated with the 100BASE-TX driver to allow for transmission using the same magnetics.
They are internally wave-shaped and pre-emphasized into outputs with typical 2.3V amplitude. The harmonic contents
are at least 27 dB below the fundamental frequency when driven by an all-ones Manchester-encoded signal.
3.1.9
10BASE-T RECEIVE
On the receive side, input buffers and level detecting squelch circuits are employed. A differential input receiver circuit
and a phase-locked loop (PLL) perform the decoding function.
The Manchester-encoded data stream is separated into clock signal and NRZ data. A squelch circuit rejects signals with
levels less than 400 mV or with short pulse widths to prevent noise at the RXP1 or RXM1 input from falsely triggering
the decoder. When the input exceeds the squelch limit, the PLL locks onto the incoming signal and the KSZ8463
decodes a data frame. The receiver clock is maintained active during idle periods in between data reception.
3.1.10
MDI/MDI-X AUTO CROSSOVER
To eliminate the need for crossover cables between similar devices, the KSZ8463 supports HP-Auto MDI/MDI-X and
IEEE 802.3u standard MDI/MDI-X auto crossover. HP-Auto MDI/MDI-X is the default.
The auto-sense function detects remote transmit and receive pairs and correctly assigns the transmit and receive pairs
for the KSZ8463. This feature is extremely useful when end users are unaware of cable types in addition to saving on
an additional uplink configuration connection. The auto-crossover feature can be disabled through the port control registers. The IEEE 802.3u standard MDI and MDI-X definitions are in Table 3-1.
TABLE 3-1:
MDI/MDI-X PIN DEFINITION
MDI
MDI-X
RJ-45 Pin
Signal
RJ-45 Pin
Signal
1
2
TD+
1
RD+
TD–
2
RD–
3
RD+
3
TD+
6
RD–
6
TD–
DS00002642A-page 18
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
3.1.11
STRAIGHT CABLE
A straight cable connects an MDI device to an MDI-X device, or an MDI-X device to an MDI device. Figure 3-1 depicts
a typical straight cable connection between a network interface card (NIC) and a switch, or hub (MDI-X).
FIGURE 3-1:
TYPICAL STRAIGHT CABLE CONNECTION
10/100 Ethernet
Media Dependent Interface
10/100 Ethernet
Media Dependent Interface
1
1
2
2
Transmit Pair
Receive Pair
3
Straight
Cable
3
4
4
5
5
6
6
7
7
8
8
Receive Pair
Modular Connector
(RJ-45)
NIC
2018 Microchip Technology Inc.
Transmit Pair
Modular Connector
(RJ-45)
HUB
(Repeater or Switch)
DS00002642A-page 19
KSZ8463ML/RL/FML/FRL
3.1.12
CROSSOVER CABLE
A crossover cable connects an MDI device to another MDI device, or an MDI-X device to another MDI-X device.
Figure 3-2 shows a typical crossover cable connection between two chips or hubs (two MDI-X devices).
FIGURE 3-2:
TYPICAL CROSSOVER CABLE CONNECTION
10/100 Ethernet
Media Dependent Interface
1
Receive Pair
10/100 Ethernet
Media Dependent Interface
Crossover
Cable
1
Receive Pair
2
2
3
3
4
4
5
5
6
6
7
7
8
8
Transmit Pair
Transmit Pair
Modular Connector (RJ-45)
HUB
(Repeater or Switch)
3.1.13
Modular Connector (RJ-45)
HUB
(Repeater or Switch)
AUTO-NEGOTIATION
The KSZ8463 conforms to the auto-negotiation protocol as described by IEEE 802.3. It allows each port to operate at
either 10BASE-T or 100BASE-TX. Auto-negotiation allows unshielded twisted pair (UTP) link partners to select the best
common mode of operation. In auto-negotiation, the link partners advertise capabilities across the link to each other and
then compare their own capabilities with those they received from their link partners. The highest speed and duplex setting that is common to the two link partners is selected as the mode of operation. Auto-negotiation is also used to negotiate support for Energy Efficient Ethernet (EEE). Auto-negotiation is only supported on ports in copper mode, not fiber
mode.
The following list shows the speed and duplex operation mode from highest to lowest.
•
•
•
•
Priority 1: 100BASE-TX, full-duplex
Priority 2: 100BASE-TX, half-duplex
Priority 3: 10BASE-T, full-duplex
Priority 4: 10BASE-T, half-duplex
If auto-negotiation is not supported or the link partner to the KSZ8463 is forced to bypass auto-negotiation, the mode is
automatically set by observing the signal at the receiver. This is known as parallel mode because while the transmitter
is sending auto-negotiation advertisements, the receiver is listening for advertisements or a fixed signal protocol.
The auto-negotiation link up process is shown in the following flow chart.
DS00002642A-page 20
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
FIGURE 3-3:
AUTO-NEGOTIATION FLOW CHART
START AUTO-NEGOTIATION
FORCE LINK SETTING
NO
PARALLEL
OPERATION
YES
BYPASS AUTO-NEGOTIATION
AND SET LINK MODE
ATTEMPT AUTONEGOTIATION
LISTEN FOR 100BASE-TX
IDLES
LISTEN FOR 10BASE-T
LINK PULSES
NO
JOIN FLOW
LINK MODE SET?
YES
LINK MODE SET
3.1.14
LINKMD® CABLE DIAGNOSTICS
The KSZ8463 LinkMD uses time domain reflectometry (TDR) to analyze the cabling plant for common cabling problems
such as open circuits, short circuits, and impedance mismatches.
LinkMD works by sending a pulse of known amplitude and duration down the MDI and MDI-X pairs and then analyzes
the shape of the reflected signal. Timing the pulse duration gives an indication of the distance to the cabling fault with a
maximum distance of 200m and an accuracy of ±2m. Internal circuitry displays the TDR information in a user-readable
digital format in register P1SCSLMD[8:0] or P2SCSLMD[8:0].
Cable diagnostics are only valid for copper connections. Fiber-optic operation is not supported.
3.1.14.1
Access
LinkMD is initiated by accessing register P1SCSLMD (0x07C) or P2SCSLMD (0x094), the PHY special control/status
and LinkMD register.
2018 Microchip Technology Inc.
DS00002642A-page 21
KSZ8463ML/RL/FML/FRL
3.1.14.2
Usage
Before initiating LinkMD, the value 0x8008 must be written to the ANA_CNTRL_3 Register (0x74C – 0x74D). This needs
to be done once (after power-n reset), but does not need to be repeated for each initiation of LinkMD. Auto-MDIX must
also be disabled before using LinkMD. To disable Auto-MDIX, write a ‘1’ to P1CR4[10] or P2CR4[10] to enable manual
control over the pair used to transmit the LinkMD pulse. The self-clearing cable diagnostic test enable bit,
P1SCSLMD[12] or P2SCSLMD[12], is set to ‘1’ to start the test on this pair.
When bit P1SCSLMD[12] or P2SCSLMD[12] returns to ‘0’, the test is completed. The test result is returned in bits
P1SCSLMD[14:13] or P2SCSLMD[14:13] and the distance is returned in bits P1SCSLMD[8:0] or P2SCSLMD[8:0]. The
cable diagnostic test results are as follows:
•
•
•
•
00 = Valid test, normal condition
01 = Valid test, open circuit in cable
10 = Valid test, short-circuit in cable
11 = Invalid test, LinkMD® failed
If P1SCSLMD[14:13] or P2SCSLMD[14:13] is “11”, this indicates an invalid test. This occurs when the KSZ8463 is
unable to shut down the link partner. In this instance, the test is not run, because it is not possible for the KSZ8463 to
determine if the detected signal is a reflection of the signal generated or a signal from another source.
Cable distance can be approximated by utilizing the following formula:
• P1SCSLMD[8:0] x 0.4m for port 1 cable distance
• P2SCSLMD[8:0] x 0.4m for port 2 cable distance
This constant (0.4m) may be calibrated for different cabling conditions, including cables with a velocity of propagation
that varies significantly from the norm.
3.1.15
ON-CHIP TERMINATION RESISTORS
Using the KSZ8463 reduces board cost and simplifies board layout by using on-chip termination resistors for the RX/
TX differential pairs, eliminating the need for external termination resistors in copper mode. The internal chip termination
and biasing provides significant power savings when compared with using external biasing and termination resistors.
3.1.16
LOOPBACK SUPPORT
The KSZ8463 provides two loopback modes. One is near-end (remote) loopback to support remote diagnosing of failures on line side, and the other is far-end loopback to support local diagnosing of failures through all blocks of the device.
In loopback mode, the speed of the PHY port will be set to 100BASE-TX full-duplex mode.
3.1.16.1
Far-End Loopback
Far-end loopback is conducted between the KSZ8463’s two PHY ports. The loopback path starts at the “originating”
PHY port’s receive inputs (RXP/RXM), wraps around at the “loopback” PHY port’s PMD/PMA (Physical Media Dependent/Physical Media Attachment), and ends at the “Originating” PHY port’s transmit outputs (TXP/TXM).
Bit[8] of registers P1CR4 and P2CR4 is used to enable far-end loopback for ports 1 and 2, respectively. As an alternative, bit[14] of registers P1MBCR and P2MBCR can be used to enable far-end loopback. The far-end loopback path is
illustrated in Figure 3-4.
3.1.16.2
Near-End (Remote) Loopback
Near-end (remote) loopback is conducted at either PHY port 1 or PHY port 2 of the KSZ8463. The loopback path starts
at the PHY port’s receive inputs (RXPx/RXMx), wraps around at the same PHY port’s PMD/PMA, and ends at the same
PHY port’s transmit outputs (TXPx/TXMx). Bit[1] of registers P1PHYCTRL and P2PHYCTRL is used to enable near-end
loopback for ports 1 and 2, respectively. As an alternative, bit[9] of registers P1SCSLMD and P2SCSLMD can be used
to enable near-end loopback. The near-end loopback paths for port 1 and port 2 are illustrated in Figure 3-4.
DS00002642A-page 22
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
FIGURE 3-4:
NEAR-END AND FAR-END LOOPBACK
ORIGINATING PHY
PORT 1
TXP1/TXM1
RXP1/RXM1
3.2
3.2.1
PORT 1 PHY NEAR
END (REMOTE) LOOPBACK
TXP1/TXM1
RXP1/RXM1
PMD1/PMA1
PMD1/PMA1
PCS1
PCS1
MAC1
MAC1
SWITCH
SWITCH
MAC 2
MAC 2
PCS2
PCS2
PMD2/PMA2
PMD2/PMA2
PHY PORT 2
FAR-END LOOPBACK
PORT 2 PHY NEAR
END (REMOTE) LOOPBACK
Media Access Controller (MAC) Block
MAC OPERATION
The KSZ8463 strictly abides by IEEE 802.3 standards to maximize compatibility. Additionally, there is an added MAC
filtering function to filter unicast packets. The MAC filtering function is useful in applications such as VoIP where restricting certain packets reduces congestion and thus improves performance.
3.2.2
ADDRESS LOOKUP
The internal Dynamic MAC Address lookup table stores MAC addresses and their associated information. It contains a
1K entry unicast address learning table plus switching information.
The KSZ8463 is guaranteed to learn 1K addresses and distinguishes itself from hash-based lookup tables, which,
depending on the operating environment and probabilities, may not guarantee the absolute number of addresses they
can learn.
3.2.3
LEARNING
The internal lookup engine updates the Dynamic MAC Address table with a new entry if the following conditions are met:
• The received packet's source address (SA) does not exist in the lookup table.
• The received packet has no receiving errors, and the packet size is of legal length.
The lookup engine inserts the qualified SA into the table, along with the port number and time stamp. If the table is full,
the oldest entry of the table is deleted to make room for the new entry.
3.2.4
MIGRATION
The internal lookup engine also monitors whether a station has moved. If a station has moved, it updates the table
accordingly. Migration happens when the following conditions are met:
• The received packet's SA is in the table but the associated source port information is different.
• The received packet has no receiving errors, and the packet size is of legal length.
2018 Microchip Technology Inc.
DS00002642A-page 23
KSZ8463ML/RL/FML/FRL
The lookup engine updates the existing record in the table with the new source port information.
3.2.5
AGING
The lookup engine updates the time stamp information of a record whenever the corresponding SA appears. The time
stamp is used in the aging process. If a record is not updated for a period of time, the lookup engine removes the record
from the table. The lookup engine constantly performs the aging process and continuously removes aging records. The
aging period is about 300 seconds (±75 seconds). This feature can be enabled or disabled through global register
SGCR1[10].
3.2.6
FORWARDING
The KSZ8463 forwards packets using the algorithm that is depicted in the following flowcharts. Figure 3-5 shows stage
one of the forwarding algorithm where the search engine looks up the VLAN ID, static table, and dynamic table for the
destination address, and comes up with “port to forward 1” (PTF1). PTF1 is then further modified by spanning tree,
IGMP snooping, port mirroring, and port VLAN processes to come up with “port-to-forward 2” (PTF2), as shown in
Figure 3-6. The packet is sent to PTF2.
The KSZ8463 will not forward the following packets:
• Error packets: These include framing errors, frame check sequence (FCS) errors, alignment errors, and illegal
size packet errors.
• IEEE802.3x PAUSE frames: KSZ8463 intercepts these packets and performs full duplex flow control accordingly.
"Local" packets: Based on destination address (DA) lookup. If the destination port from the lookup table matches the
port from which the packet originated, the packet is defined as "local."
FIGURE 3-5:
DESTINATION ADDRESS LOOKUP FLOW CHART IN STAGE ONE
START
PTF1 = NULL
NO
VLAN ID
VALID?
- SEARCH VLAN TABLE
- INGRESS VLAN FILTERING
- DISCARD NPVID CHECK
YES
SEARCH COMPLETE
GET PTF1 FROM
STATIC MAC TABLE
FOUND
SEARCH
STATIC
TABLE
THIS SEARCH IS BASED ON
DA or DA+FID
NOT
FOUND
SEARCH COMPLETE
GET PTF1 FROM
DYNAMIC MAC
TABLE
FOUND
DYNAMIC
TABLE
SEARCH
THIS SEARCH IS BASED ON
DA+FID
NOT
FOUND
SEARCH COMPLETE
GET PTF1 FROM
VLAN TABLE
PTF1
DS00002642A-page 24
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
FIGURE 3-6:
DESTINATION ADDRESS RESOLUTION FLOW CHART IN STAGE TWO
PTF1
SPANNING
TREE
PROCESS
- CHECK RECEIVING PORT’S RECEIVE ENABLE BIT
- CHECK DESTINATION PORT’S TRANSMIT ENABLE BIT
- CHECK WHETHER PACKETS ARE SPECIAL (BPDU) OR SPECIFIED
- APPLIED TO MAC1 AND MAC2
IGMP
PROCESS
PORT MIRROR
PROCESS
- IGMP WILL BE FORWARDED TO THE HOST PORT
- RX MIRROR
- TX MIRROR
- RX OR TX MIRROR
- RX AND TX MIRROR
PORT VLAN
MEMBERSHIP
CHECK
PTF2
3.2.7
INTER-PACKET GAP (IPG)
If a frame is successfully transmitted, then the minimum 96-bit time for IPG is measured between two consecutive packets. If the current packet is experiencing collisions, the minimum 96-bit time for IPG is measured from carrier sense
(CRS) to the next transmit packet.
3.2.8
BACK-OFF ALGORITHM
The KSZ8463 implements the IEEE standard 802.3 binary exponential back-off algorithm in half-duplex mode. After 16
collisions, the packet is dropped.
3.2.9
LATE COLLISION
If a transmit packet experiences collisions after 512 bit times of the transmission, the packet is dropped.
3.2.10
LEGAL PACKET SIZE
The KSZ8463 discards packets less than 64 bytes and can be programmed to accept packet sizes up to 1536 bytes in
SGCR2[1]. The KSZ8463 can also be programmed for special applications to accept packet sizes up to 2000 bytes in
SGCR1[4].
3.2.11
FLOW CONTROL
The KSZ8463 supports standard 802.3x flow control frames in both the transmit and receive directions.
In the receive direction, if a PAUSE control frame is received on any port, the KSZ8463 will not transmit the next normal
frame on that port until the timer, specified in the PAUSE control frame, expires. If another PAUSE frame is received
before the current timer expires, the timer will then update with the new value in the second PAUSE frame. During this
period (while it is flow controlled), only flow control packets from the KSZ8463 are transmitted.
2018 Microchip Technology Inc.
DS00002642A-page 25
KSZ8463ML/RL/FML/FRL
In the transmit direction, the KSZ8463 has intelligent and efficient ways to determine when to invoke flow control and
send PAUSE frames. The flow control is based on availability of the system resources, including available buffers, available transmit queues and available receive queues.
The KSZ8463 issues a PAUSE frame containing the maximum pause time defined in IEEE standard 802.3x. Once the
resource is freed up, the KSZ8463 sends out another flow control frame with zero pause time to turn off the flow control
(turn on transmission to the port). A hysteresis feature is provided to prevent the flow control mechanism from being
constantly activated and deactivated.
3.2.12
HALF-DUPLEX BACKPRESSURE
A half-duplex backpressure option (non-IEEE 802.3 standards) is also provided. The activation and deactivation conditions are the same as in full-duplex mode. If backpressure is required, the KSZ8463 sends preambles to defer the other
stations' transmission (carrier sense deference).
To avoid jabber and excessive deference (as defined in the 802.3 standard), after a certain time, the KSZ8463 discontinues the carrier sense and then raises it again quickly. This short silent time (no carrier sense) prevents other stations
from sending out packets thus keeping other stations in a carrier sense deferred state. If the port has packets to send
during a backpressure situation, the carrier sense type backpressure is interrupted and those packets are transmitted
instead. If there are no additional packets to send, carrier sense type backpressure is reactivated again until chip
resources free up. If a collision occurs, the binary exponential back-off algorithm is skipped and carrier sense is generated immediately, thus reducing the chance of further collision and carrier sense is maintained to prevent packet reception.
To ensure no packet loss in 10BASE-T or 100BASE-TX half-duplex mode, the user must enable the following bits:
• Aggressive back-off (bit [8] in SGCR1)
• No excessive collision drop (bit [3] in SGCR2)
• Backpressure flow control enable (bit [11] in P1CR2/P2CR2)
Please note that these bits are not set in default because this is not the IEEE standard.
3.2.13
BROADCAST STORM PROTECTION
The KSZ8463 has an intelligent option to protect the switch system from receiving too many broadcast packets. As the
broadcast packets are forwarded to all ports except the source port, an excessive number of switch resources (bandwidth and available space in transmit queues) may be utilized. The KSZ8463 has the option to include “multicast packets” for storm control. The broadcast storm rate parameters are programmed globally, and can be enabled or disabled
on a per port basis in P1CR1[7] and P2CR1[7]. The rate is based on a 67ms interval for 100BASE-TX and a 670 ms
interval for 10BASE-T. At the beginning of each interval, the counter is cleared to zero and the rate limit mechanism
starts to count the number of bytes during the interval. The rate definition is described in SGCR3[2:0][15:8]. The default
setting is 0x63 (99 decimal). This is equal to a rate of 1%, calculated as follows:
EQUATION 3-1:
148 000 frames/sec 67ms/interval 1% = 99 frames/interval (appx.) = 0x63
148,800 frames/sec is based on 64-byte block of packets in 100BASE-T with 12 bytes of IPG and 8 bytes of preamble
between two packets.
3.2.14
PORT INDIVIDUAL MAC ADDRESS AND SOURCE PORT FILTERING
The KSZ8463 can provide individual MAC addresses for port 1 and port 2. They can be set at registers 0x0B0h –
0x0B5h and 0x0B6 – 0x0BB. Received packets can be filtered (dropped) if their source address matches the MAC
address of port 1 or port 2. This feature can be enabled by setting bits [11:10] in the P1CR1 or P2CR1 registers. One
example of usage is that a packet will be dropped after it completes a full round trip within a ring network.
DS00002642A-page 26
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
3.3
3.3.1
Switch Block
SWITCHING ENGINE
The KSZ8463 features a high-performance switching engine to move data to and from the MAC’s packet buffers. It operates in store and forward mode, while the efficient switching mechanism reduces overall latency. The switching engine
has a 32 KByte internal frame buffer. This resource is shared between all the ports. There are a total of 256 buffers available. Each buffer is sized at 128 Bytes.
3.3.2
SPANNING TREE SUPPORT
To support spanning tree, the host port is the designated port for the processor. The other ports (port 1 and port 2) can
be configured in one of the five spanning tree states via “transmit enable”, “receive enable”, and “learning disable” register settings in registers P1CR2 and P2CR2 for ports 1 and 2, respectively. Table 3-2 shows the setting and software
actions taken for each of the five spanning tree states.
TABLE 3-2:
SPANNING TREE STATES
Disable State
Port Setting
Software Action
The port should not forward or receive any packets. Learning is disabled.
transmit enable = “0”,
receive enable = “0”,
learning disable = “1”
The processor should not send any packets to the port. The
switch may still send specific packets to the processor
(packets that match some entries in the “Static MAC Table”
with “overriding bit” set) and the processor should discard
those packets. Address learning is disabled on the port in
this state.
Blocking State
Port Setting
Software Action
transmit enable = “0”,
Only packets to the procesreceive enable = “0”,
sor are forwarded.
learning disable = “1”
The processor should not send any packets to the port(s) in
this state. The processor should program the “Static MAC
Table” with the entries that it needs to receive (for example,
BPDU packets). The “overriding” bit should also be set so
that the switch will forward those specific packets to the processor. Address learning is disabled on the port in this state.
Listening State
Port Setting
Software Action
Only packets to and from
the processor are forwarded. Learning is disabled.
transmit enable = “0”,
receive enable = “0”,
learning disable = “1”
The processor should program the “Static MAC Table” with
the entries that it needs to receive (for example, BPDU
packets). The “overriding” bit should be set so that the
switch will forward those specific packets to the processor.
The processor may send packets to the port(s) in this state.
Address learning is disabled on the port in this state.
Learning State
Port Setting
Software Action
Only packets to and from
the processor are forwarded. Learning is
enabled.
transmit enable = “0”,
receive enable = “0”,
learning disable = “0”
The processor should program the “Static MAC Table” with
the entries that it needs to receive (for example, BPDU
packets). The “overriding” bit should be set so that the
switch will forward those specific packets to the processor.
The processor may send packets to the port(s) in this state.
Address learning is enabled on the port in this state.
Forwarding State
Port Setting
Software Action
transmit enable = “1”,
receive enable = “1”,
learning disable = “0”
The processor programs the “Static MAC Table” with the
entries that it needs to receive (for example, BPDU packets). The “overriding” bit is set so that the switch forwards
those specific packets to the processor. The processor can
send packets to the port(s) in this state. Address learning is
enabled on the port in this state.
Packets are forwarded and
received normally. Learning is enabled.
2018 Microchip Technology Inc.
DS00002642A-page 27
KSZ8463ML/RL/FML/FRL
3.3.3
RAPID SPANNING TREE SUPPORT
There are three operational states assigned to each port for RSTP (Discarding, Learning, and Forwarding):
• Discarding ports do not participate in the active topology and do not learn MAC addresses.
• Discarding state: the state includes three states of the disable, blocking and listening of STP.
• Port setting: transmit enable = “0”, receive enable = “0”, learning disable = “1”.
3.3.3.1
Discarding State
Software action: The host processor should not send any packets to the port. The switch may still send specific packets
to the processor (packets that match some entries in the static table with “overriding bit” set) and the processor should
discard those packets. When the port’s learning capability (learning disable = ‘1’) is disabled, setting bits [10:9] in the
SGCR8 register will rapidly flush the port related entries in the dynamic MAC table and static MAC table.
The processor is connected to port 3 via the host interface. Address learning is disabled on the port in this state.
3.3.3.2
Learning State
Ports in “learning states” learn MAC addresses, but do not forward user traffic.
Learning State: Only packets to and from the processor are forwarded. Learning is enabled.
Port setting for Learning State: transmit enable = “0”, receive enable = “0”, learning disable = “0”.
Software action: The processor should program the static MAC table with the entries that it needs to receive (e.g., BPDU
packets). The “overriding” bit should be set so that the switch will forward those specific packets to the processor. The
processor may send packets to the port(s) in this state (see the Tail Tagging Mode sub-section for details). Address
learning is enabled on the port in this state.
Ports in “forwarding states” fully participate in both data forwarding and MAC learning.
3.3.3.3
Forwarding State
Forwarding state: Packets are forwarded and received normally. Learning is enabled.
Port setting: transmit enable = “1”, receive enable = “1”, learning disable = “0”.
Software action: The processor should program the static MAC table with the entries that it needs to receive (e.g., BPDU
packets). The “overriding” bit should be set so that the switch will forward those specific packets to the processor. The
processor may send packets to the port(s) in this state (see the Tail Tagging Mode sub-section for details). Address
learning is enabled on the port in this state.
RSTP uses only one type of BPDU called RSTP BPDUs. They are similar to STP configuration BPDUs with the exception of a type field set to “version 2” for RSTP and “version 0” for STP, and a flag field carrying additional information.
3.3.4
TAIL TAGGING MODE
The tail tag is only seen and used by the port 3 host interface, which should be connected to a processor. It is an effective
way to retrieve the ingress port information for spanning tree protocol, IGMP snooping, and other applications. Bits [1:0]
in the one byte tail tagging are used to indicate the source/destination port in port 3. Bits[3:2] are used for priority setting
of the ingress frame in port 3. Other bits are not used. The tail tag feature is enabled by setting bit[8] in the SGCR8
register.
FIGURE 3-7:
BYTES
TAIL TAG FRAME FORMAT
8
6
6
2
2
2
PREAMBLE
DA
SA
VPID
TCI
LENGTH
DS00002642A-page 28
46-1500
LLC
DATA
1
4
TAIL TAG
FCS
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 3-3:
TAIL TAG RULES
Ingress to Port 3 (Host to KSZ8463)
Bit[1:0]
Destination Port
00
Normal (Address Look up)
01
Port 1
10
Port 2
11
Port 1 and Port 2
Bit[3:2]
Frame Priority
00
Priority 0
01
Priority 1
10
Priority 2
11
Priority 3
Egress from Port 3 (KSZ8463 to Host)
3.3.5
Bit[0]
Source Port
0
Port 1
1
Port 2
IGMP SUPPORT
For Internet Group Management Protocol (IGMP) support in Layer 2, the KSZ8463 provides two components:
3.3.5.1
IGMP Snooping
The KSZ8463 traps IGMP packets and forwards them only to the processor (host port). The IGMP packets are identified
as IP packets (either Ethernet IP packets, or IEEE 802.3 SNAP IP packets) with IP version = 0x4 and protocol version
number = 0x2.
3.3.5.2
Multicast Address Insertion in the Static MAC Table
Once the multicast address is programmed in the Static MAC Address Table, the multicast session is trimmed to the
subscribed ports, instead of broadcasting to all ports.
To enable IGMP support, set bit[14] to ‘1’ in the SGCR2 register. Also, Tail Tagging Mode needs to be enabled, so that
the processor knows which port the IGMP packet was received on. This is achieved by setting bit [8] to ‘1’ in the SGCR8
register.
3.3.6
IPV6 MLD SNOOPING
The KSZ8463 traps IPv6 Multicast Listener Discovery (MLD) packets and forwards them only to the processor (host
port). MLD snooping is controlled by SGCR2, bit[13] (MLD snooping enable) and SGCR2 bit[12] (MLD option).
Setting SGCR2 bit[13] causes the KSZ8463 to trap packets that meet all of the following conditions:
•
•
•
•
IPv6 multicast packets
Hop count limit = “1”
IPv6 next header = “1”or “58” (or = “0” with hop-by-hop next header = “1” or “58”)
If SGCR2[12] = “1”, IPv6 next header = “43”, “44”, “50”, “51”, or “60” (or = “0” with hop-by-hop next header = “43”,
“44”, “50”, “51”, or “60”)
3.3.7
PORT MIRRORING SUPPORT
KSZ8463 supports port mirroring comprehensively as:
3.3.7.1
“Receive Only” Mirror-on-a-Port
All the packets received on the port are mirrored on the sniffer port. For example, 1 is programmed to be “receive sniff”
and the host port is programmed to be the “sniffer”. A packet received on port 1 is destined to port 2 after the internal
lookup. The KSZ8463 forwards the packet to both port 2 and the host port. The KSZ8463 can optionally even forward
“bad” received packets to the “sniffer port”.
2018 Microchip Technology Inc.
DS00002642A-page 29
KSZ8463ML/RL/FML/FRL
3.3.7.2
“Transmit Only” Mirror-on-a-Port
All the packets transmitted on the port are mirrored on the sniffer port. For example, port 1 is programmed to be “transmit
sniff” and the host port is programmed to be the “sniffer port”. A packet received on port 2 is destined to port 1 after the
internal lookup. The KSZ8463 forwards the packet to both port 1 and the host port.
3.3.7.3
“Receive and Transmit” Mirror-on-Two-Ports
All the packets received on port A and transmitted on port B are mirrored on the sniffer port. To turn on the “AND” feature,
set register SGCR2, bit 8 to “1”. For example, port 1 is programmed to be “receive sniff”, port 2 is programmed to be
“transmit sniff”, and the host port is programmed to be the “sniffer port”. A packet received on port 1 is destined to port
2 after the internal lookup. The KSZ8463 forwards the packet to both port 2 and the host port.
Multiple ports can be selected as “receive sniff” or “transmit sniff”. In addition, any port can be selected as the “sniffer
port”. All these per port features can be selected through registers P1CR2, P2CR2, and P3CR2 for ports 1, 2, and the
host port, respectively.
3.3.7.4
IEEE 802.1Q VLAN Support
The KSZ8463 supports 16 active VLANs out of the 4096 possible VLANs specified in the IEEE 802.1Q specification.
KSZ8463 provides a 16-entry VLAN table, which converts the 12-bits VLAN ID (VID) to the 4-bits Filter ID (FID) for
address lookup. If a non-tagged or null-VID-tagged packet is received, the ingress port default VID is used for lookup.
In VLAN mode, the lookup process starts with VLAN table lookup to determine whether the VID is valid. If the VID is not
valid, the packet is dropped and its address is not learned. If the VID is valid, the FID is retrieved for further lookup. The
FID + Destination Address (FID+DA) are used to determine the destination port. The FID + Source Address (FID+SA)
are used for address learning (see Table 3-4 and Table 5).
Advanced VLAN features are also supported in the KSZ8463, such as “VLAN ingress filtering” and “discard non PVID”
defined in bits [14:13] of P1CR2, P2CR2 and P3CR2 registers. These features can be controlled on per port basis.
TABLE 3-4:
FID + DA LOOKUP IN VLAN MODE
DA found in
Static MAC
Table?
Use FID
Flag?
FID Match?
DA+FID
found in
Dynamic
MAC
Table?
No
Don’t Care
Don’t Care
No
Broadcast to the membership ports defined in the VLAN
Table bits [18:16].
No
Don’t Care
Don’t Care
Yes
Send to the destination port defined in the Dynamic MAC
Address Table bits [53:52].
Yes
0
Don’t Care
Don’t Care
Send to the destination port(s) defined in the Static MAC
Address Table bits [50:48].
Yes
1
No
No
Broadcast to the membership ports defined in the VLAN
Table bits [18:16].
Yes
1
No
Yes
Send to the destination port defined in the Dynamic MAC
Address Table bits [53:52].
Yes
1
Yes
Don’t Care
Send to the destination port(s) defined in the Static MAC
Address Table bits [50:48].
TABLE 3-5:
Action
FID + SA LOOKUP IN VLAN MODE
FID+SA found in Dynamic MAC Address Table?
Action
No
Learn and add FID+SA to the Dynamic MAC Address Table.
Yes
Update time stamp.
3.3.8
QUALITY-OF-SERVICE (QOS) PRIORITY SUPPORT
The KSZ8463 provides quality-of-service (QoS) for applications such as VoIP and video conferencing. The KSZ8463
offer 1, 2, and 4 priority queues option per port. This is controlled by bit[0] and bit[8] in P1CR1, P2CR1 and P3CR1 registers as shown below:
• Bit[0], bit[8] = “00” egress port is a single output queue as default.
DS00002642A-page 30
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
• Bit[0], bit[8] = “01” egress port can be split into two priority transmit queues. (Q0 and Q1)
• Bit[0], bit[8] = “10” egress port can be split into four priority transmit queues. (Q0, Q1, Q2 and Q3)
The four priority transmit queues is a new feature in the KSZ8463. Queue 3 is the highest priority queue and Queue 0
is the lowest priority queue. If a port's transmit queue is not split, high priority and low priority packets have equal priority
in the transmit queue.
There is an additional option for every port via bits[15,7] in the P1TXQRCR1, P1TXQRCR2, P2TXQRCR1, P2TXQRCR2, P3TXQRCR1, and P3TXQRCR2 Registers to select either always to deliver high priority packets first or use
weighted fair queuing for the four priority queues scale by 8:4:2:1.
3.3.9
PORT-BASED PRIORITY
With port-based priority, each ingress port is individually classified as a specific priority level. All packets received at the
high-priority receiving port are marked as high priority and are sent to the high-priority transmit queue if the corresponding transmit queue is split. bits[4:3] of registers P1CR1, P2CR1, and P3CR1 are used to enable port-based priority for
ports 1, 2, and the host port, respectively.
3.3.10
802.1P-BASED PRIORITY
For 802.1p-based priority, the KSZ8463 examines the ingress (incoming) packets to determine whether they are tagged.
If tagged, the 3-bit priority field in the VLAN tag is retrieved and used to look up the “priority mapping” value, as specified
by the register SGCR6. The “priority mapping” value is programmable.
Figure 3-8 illustrates how the 802.1p priority field is embedded in the 802.1Q VLAN tag.
802.1P PRIORITY FIELD FORMAT
1
6
6
2
PREAMBLE
DA
SA
VPID
BYTES
16
BITS
802.1q VLAN TAG
TAGGED PACKET TYPE
(8100 FOR ETHERNET
2
TCI
3
802.1p
2
4 6 -1 5 0 0
4
LENGTH
DATA
FCS
1
12
CFI
7
SFD
FIGURE 3-8:
VLAN ID
802.1p-based priority is enabled by bit[5] of registers P1CR1, P2CR1, and P3CR1 for ports 1, 2, and the host port,
respectively.
The KSZ8463 provides the option to insert or remove the priority tagged frame's header at each individual egress port.
This header, consisting of the 2 bytes VLAN protocol ID (VPID) and the 2 bytes tag control information field (TCI), is also
referred to as the 802.1Q VLAN tag.
Tag insertion is enabled by bit[2] of registers P1CR1, P2CR1, and P3CR1 for ports 1, 2, and the host port, respectively.
At the egress port, untagged packets are tagged with the ingress port’s default tag. The default tags are programmed
in register sets P1VIDCR, P2VIDCR, and P3VIDCR for ports 1, 2, and the host port, respectively. The KSZ8463 does
not add tags to already tagged packets.
Tag removal is enabled by bit[1] of registers P1CR1, P2CR1, and P3CR1 for ports 1, 2, and the host port, respectively.
At the egress port, tagged packets will have their 802.1Q VLAN tags removed. The KSZ8463 will not modify untagged
packets.
The CRC is recalculated for both tag insertion and tag removal.
2018 Microchip Technology Inc.
DS00002642A-page 31
KSZ8463ML/RL/FML/FRL
3.3.11
802.1P PRIORITY FIELD RE-MAPPING
This is a QoS feature that allows the KSZ8463 to set the “User Priority Ceiling” at any ingress port. If the ingress packet’s
priority field has a higher priority value than the default tag’s priority field of the ingress port, the packet’s priority field is
replaced with the default tag’s priority field. The “User Priority Ceiling” is enabled by bit[3] of registers P1CR2, P2CR2,
and P3CR2 for ports 1, 2, and the host port, respectively.
3.3.12
DIFFSERV-BASED PRIORITY
DiffServ-based priority uses the ToS registers shown in the TOS Priority Control Registers. The ToS priority control registers implement a fully decoded, 128-bit differentiated services code point (DSCP) register to determine packet priority
from the 6-bit ToS field in the IP header. When the most significant 6 bits of the ToS field are fully decoded, the resultant
of the 64 possibilities is compared with the corresponding bits in the DSCP register to determine priority.
3.3.13
RATE LIMITING SUPPORT
The KSZ8463 supports hardware rate limiting from 64 Kbps to 99 Mbps (refer to Ingress or Egress Data Rate Limits),
independently on the “receive side” and on the “transmit side” as per port basis. For 10BASE-T, a rate setting above
10 Mbps means the rate is not limited. On the receive side, the data receive rate for each priority at each port can be
limited by setting up ingress rate control registers. On the transmit side, the data transmit rate for each priority queue at
each port can be limited by setting up egress rate control registers. The size of each frame has options to include minimum interframe gap (IFG) or preamble byte, in addition to the data field (from packet DA to FCS).
For ingress rate limiting, KSZ8463 provides options to selectively choose frames from all types, multicast, broadcast,
and flooded unicast frames. The KSZ8463 counts the data rate from those selected type of frames. Packets are dropped
at the ingress port when the data rate exceeds the specified rate limit.
For egress rate limiting, the leaky bucket algorithm is applied to each output priority queue for shaping output traffic.
Inter frame gap is stretched on a per frame base to generate smooth, non-burst egress traffic. The throughput of each
output priority queue is limited by the egress rate specified.
If any egress queue receives more traffic than the specified egress rate throughput, packets may be accumulated in the
output queue and packet memory. After the memory of the queue or the port is used up, packet dropping or flow control
will be triggered. As a result of congestion, the actual egress rate may be dominated by flow control/dropping at the
ingress end, and may be therefore slightly less than the specified egress rate.
To reduce congestion, it is a good practice to make sure the egress bandwidth exceeds the ingress bandwidth.
3.3.14
MAC ADDRESS FILTERING FUNCTION
When a packet is received, the destination MAC address is looked up in both the static and dynamic MAC address
tables. If the address is not found in either of these tables, then the destination MAC address is “unknown”. By default,
an unknown unicast packet is forwarded to all ports except the port at which it was received. An optional feature makes
it possible to specify the port or ports to which to forward unknown unicast packets. It is also possible to specify no ports,
meaning that unknown unicast packets will be discarded. This feature is enabled by setting bit[7] in SGCR7.
The unicast MAC address filtering function is useful in preventing the broadcast of unicast packets that could degrade
the quality of this port in applications such as Voice over Internet Protocol (VoIP).
3.4
IEEE 1588 Precision Time Protocol (PTP) Block
The IEEE 1588 precision time protocol (PTP) provides a method for establishing synchronized time across nodes in an
Ethernet networking environment. The KSZ8463 implements V2 (2008) of the IEEE 1588 PTP specification.
The KSZ8463 3-port switch implements the IEEE 1588 PTP Version 2 protocol. Port 1 and port 2 can be programmed
as either end-to-end (E2E) or peer-to-peer (P2P) transparent clock (TC) ports. In addition, port 3 can be programmed
as either slave or master ordinary clock (OC) port. Ingress time stamp capture, egress time stamp recording, correction
field update with residence time and link delay, delay turn-around time insertion, egress time stamp insertion, and checksum update are supported. PTP frame filtering is implemented to enhance overall system performance. Delay adjustments are implemented to fine tune the synchronization. Versatile event trigger outputs and time stamp capture inputs
are implemented to meet various real time application requirements through GPIO pins.
The key features of the KSZ8463 implementation are as follows:
• Both one-step and two-step transparent clock (TC) operations are supported
• Implementation of precision time clock per specification
- Upper 16 bits of the second clock not implemented due to practical values of time
DS00002642A-page 32
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
•
•
•
•
•
•
•
Both E2E and P2P TC are supported on port 1 and port 2
Both slave and master OC are supported on port 3
PTP multicast and unicast frame are supported
Transports of PTP over IPv4/IPv6 UDP and IEEE 802.3/Ethernet are supported
Both path delay request-response and peer delay mechanism are supported
Precision time stamping of input signals on the GPIO pins
Creation and delivery of clocks, pulses, or other unique serial bit streams on the GPIO pins with respect to the precision time clock time.
IEEE 1588 defines two essential functions: The measurement of link and residence (switching) delays by using the
Delay_Req/Resp or Pdelay_Req/Resp messages, and the distribution of time information by using the Sync/Follow_Up
messages. The 1588 PTP event messages are periodically sent from the grandmaster in the network to all slave clock
devices. Link delays are measured by each slave node to all its link partners to compensate for the delay of PTP messages sent through the network.
The 1588 PTP Announce messages are periodically sent from the grandmaster(s) in the network to all slave clock
devices. This information is used by each node to select a master clock using the “best master clock” algorithm.
1588 PTP (Version 2) defines two types of messages: event and general messages. These are summarized below and
are supported by the KSZ8463:
Event Messages (an accurate time stamp is generated at egress and ingress):
•
•
•
•
Sync (from master to slave)
Delay_Req (from slave to master)
Pdelay_Req (between link partners for peer delay measurement)
Pdelay_Resp (between link partners for peer delay measurement)
General Messages:
•
•
•
•
•
•
Follow_Up (from Master to Slave)
Delay_Resp (from Master to Slave)
Pdelay_Resp_Follow_Up (between link partners for peer delay measurement)
Announce
Management
Signaling
3.4.1
IEEE 1588 PTP CLOCK TYPES
The KSZ8463 supports the following clock types:
• Ordinary Clock (OC) is defined as a PTP clock with a single PTP port in a PTP domain. It may serve as a source
of time such as a master clock, or it may be a slave clock which synchronizes to another master clock.
• End-to-End Transparent Clock (E2E TC) is defined as a transparent clock that supports the use of the end-to-end
delay measurement mechanism between a slave clock and the master clock. In this method, the E2E TC intermediate devices do not need to be synchronized to the master clock and the end slave node is directly synchronized
to the master clock. The E2E TC/SC slave intermediate devices can also be synchronized to the master clock.
Note that the transparent clock is not a real clock that can be viewed on an oscilloscope but rather it is a mechanism by which delay are accounted for when transporting information across and through physical network nodes.
• Peer-to-Peer Transparent Clock (P2P TC for Version 2) is defined as a transparent clock, in addition to providing
PTP event transit time information. P2P TC also provides corrections for the propagation delay between nodes
(link partners) by using Pdelay_Req (Peer Delay Request) and Pdelay_Resp (Peer Delay Response). In this
method, the P2P TC intermediate devices can be synchronized to the master clock. A transparent clock (TC) is
not part of the master-slave hierarchy. Instead, it measures the resident time which is the time taken for a PTP
message to traverse the node. The P2P TC then provides this information to the clock receiving the PTP message. In addition, the P2P TC measures and passes on the link delay of the receiving PTP message. Note that the
transparent clock is not a real clock that can be viewed on an oscilloscope but rather it is a mechanism by which
delay are accounted for when transporting information across and through physical network nodes.
• Master clock is defined as a clock which is used as the reference clock for the entire system. The KSZ8463 can
operate as a master clock if needed. However, the quality of the clock signal will be limited by the quality of the
crystal or oscillator used to clock the device.
Note that P2P and E2E TCs cannot be mixed on the same communication path.
2018 Microchip Technology Inc.
DS00002642A-page 33
KSZ8463ML/RL/FML/FRL
3.4.2
IEEE 1588 PTP ONE-STEP OR TWO-STEP CLOCK OPERATION
The KSZ8463 supports either 1-step or 2-step clock operation.
• One-Step Clock Operation: A PTP message (Sync) exchange that provides time information using a single event
message which eliminates the need for a Follow_Up message to be sent. This one-step operation will eliminate
the need for software to read the time stamp and to send a Follow_Up message.
• Two-Step Clock Operation: A PTP messages (Sync/Follow_Up) that provides time information using the combination of an event message and a subsequent general message. The Follow_Up message carries a precise estimate of the time the sync message was placed on the PTP communication path by the sending node.
3.4.3
IEEE 1588 PTP BEST MASTER CLOCK SELECTION
The IEEE 1588 PTP specification defines an algorithm based on the characteristics of the clocks and system topology
called best master clock (BMC) algorithm. BMC uses announce messages to establish the synchronization hierarchy.
The algorithm compares data from two clocks to determine the better clock. Each clock device continuously monitors
the announce messages issued by the current master and compares the dataset to itself. The software controls this
process.
3.4.4
IEEE 1588 PTP SYSTEM TIME CLOCK
The system time clock (STC) in KSZ8463 is a readable or writable time source for all IEEE 1588 PTP-related functions
and contains three counters: a 32-bit counter for seconds, a 30-bit counter for nanoseconds and a 32-bit counter for
sub-nanoseconds (units of 2-32 ns). Figure 3-9 shows the PTP Clock.
FIGURE 3-9:
PTP SYSTEM CLOCK OVERVIEW
SECONDS
32 BITS
25MHz
125MHz
NANO-SECONDS
32 BITS
25MHz, 5-SUBPHASE
COUNTER
SUB NANO-SECONDS
30 BITS
EVERY 40ns,
ADD 40ns TO
COUNTER
SUB NS ADJUSTMENT
30 BITS
ALL THE SUB-BLOCKS ABOVE ARE READABLE AND WRITABLE BY THE PROCESSOR.
ALL OF THE OUTPUTS OF THE SUB-BLOCKS ABOVE ARE CAPTURED, STORED,
AND USED FOR TIMESTAMPS BY THE OTHER PARTS OF THE DEVICE
The STC is clocked (incremented by 40 ns or updated with sub-nanosecond carry info) every 40 ns by a derivative of
the 125 MHz derived clock. The 30-bit nanosecond counter will be numerically incremented by 40 ns every 40 ns. There
is another 3-bit phase counter that is designed to indicate one of the five sub-phases (0 ns, 8 ns, 16 ns, 24 ns, or 32 ns)
within the 40 ns period. This provides finer resolution for the various messages and time stamps. The overflow for the
30-bit nanosecond counter is 0x3B9ACA00 (109) and the overflow for the 32-bit sub-nanosecond counter is
0xFFFFFFFF.
DS00002642A-page 34
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
The system time clock does not support the upper 16-bits of the seconds field as defined by the IEEE 1588 PTP Version
2 which specifies a 48-bit seconds field. If the 32-bit seconds counter overflows, it will have to be handled by software.
Note that an overflow of the seconds field only occurs every 136 years.
The seconds value is kept track of in the PTP_RTC_SH and PTP_RTC_SL registers (0x608 – 0x60B). The nanoseconds value is kept track of in the PTP_RTC_NSH and PTP_RTC_NSL registers (0x604 – 0x607).
The PTP_RTC_PHASE clock register (0x60C – 0x60D) is initialized to zero whenever the local processor writes to the
PTP_RTC_NSL, PTP_RTC_NSH, PTP_RTC_SL, and PTP_RTC_SH registers.
During normal operation when the STC clock is keeping synchronized real time, and not while it is undergoing any initialization manipulation by the processor to get it close to the real time, the PTP_RTC_PHASE clock register will be reset
to zero at the beginning of the current 40 ns STC clock update interval. It will start counting at zero at the beginning of
the 40 ns period and every 8 ns it will be incremented. The information provided by the PTP_RTC_PHASE register will
increase the accuracy of the various time stamps and STC clock readings.
3.4.5
UPDATING THE SYSTEM TIME CLOCK
The KSZ8463 provides four mechanisms for updating the system time clock:
•
•
•
•
Directly Setting or Reading the Time
Step-Time Adjustment
Continuous Time Adjustment
Temporary Time Adjustment
3.4.5.1
Directly Setting or Reading the Time
Directly setting the system time clock to a value is accomplished by setting a new time in the real time clock registers
(PTP_RTC_SH/L, PTP_RTC_NSH/L and PTP_RTC_PHASE) and then setting the load PTP 1588 clock bit (PTP_LOAD_CLK).
Directly reading the system time clock is accomplished by setting the read PTP 1588 clock bit (PTP_READ_CLK). To
avoid lower bits overflowing during reading the system time clock, a snapshot register technique is used. The value in
the system time clock will be saved into a snapshot register by setting the PTP_READ_CLK bit in PTP_CLK_CTL, and
then subsequent reads from PTP_RTC_S, PTP_RTC_NS, and PTP_RTC_PHASE will return the system time clock
value. The CPU will add the PTP_RTC_PHASE value to PTP_RTC_S and PTP_RTC_NS to get the exact real time.
3.4.5.2
Step-Time Adjustment
The system time clock can be incremented in steps if desired. The nanosecond value (PTP_RTC_NSH/L) can be added
or subtracted when the PTP_STEP_ADJ_CLK bit is set. The value will be added to the system time clock if this action
occurs while the PTP_STEP_DIR bit = “1”. The value will be subtracted from the system time clock if this action occurs
while the PTP_STEP_DIR bit = “0”. The PTP_STEP_ADJ_CLK bit is self-clearing.
3.4.5.3
Continuous Time Adjustment
The system can be set up to perform continuous time adjustment to the 1588 PTP clock. This is the mode that is anticipated to be used the most. This mode is overseen by the local processor and provides a method of periodically adjusting the count of the PTP clock to match the time of the master clock as best as possible. The rate registers
(PTP_SNS_RATE_H and PTP_SNS_RATE_L) (0x610 – 0x613) are used to provide a value by which the sub-nanosecond Portion of the clock is adjusted on a periodic basis. While continuous adjustment mode (PTP_CONTINU_ADJ_CLK
= “1”) is selected every 40 ns the sub-nanosecond value of the clock will be adjusted in either a positive or negative
direction as determined by the PTP_RATE_DIR bit. The value will be positively adjusted if PTP_RATE_DIR = “0” or negatively adjusted if PTP_RATE_DIR = “1”. The rate adjustment allows for correction with resolution of 2-32 ns for every
40 ns reference clock cycle, and it will be added to or subtracted from the system time clock on every reference clock
cycle right after the write to PTP_SNC_RATE_L is done. To stop the continuous time adjustment, one can either set the
PTP_CONTINU_ADJ_CLK = “0” or the PTP_SNS_RATE_H/L value to zero.
3.4.5.4
Temporary Time Adjustment
This mode allows for the continuous time adjustment to take place over a specified period of time only. The period of
time is specified in the PTP_ADJ_DURA_H/L registers. This mode is enabled by setting the PTP_TEMP_ADJ_CLK bit
to one. Once the duration is reached, the increment or decrement will cease. When the temporary time adjustment is
done, the internal duration counter register (PTP_ADJ_DURA_H/L) will stay at zero, which will disable the time adjustment. The local processor needs to set the PTP_TEMP_ADJ_CLK to one again to start another temporary time adjustment with the reloaded value into the internal rate and duration registers. The PTP_ADJ_DURA_L register needs to be
2018 Microchip Technology Inc.
DS00002642A-page 35
KSZ8463ML/RL/FML/FRL
programmed before PTP_ADJ_DURA_H register. The PTP_ADJ_DURA_L, PTP_ADJ_DURA_H and
PTP_SNS_RATE_L registers need to be programmed before the PTP_SNS_RATE_H register. The temporary time
adjustment will start after the PTP_TEMP_ADJ_CLK bit is set to one. This bit is self-cleared when the adjustment is
completed. Software can read this bit to check whether the adjustment is still in progress.
3.4.5.5
PTP Clock Initialization
During software initialization when the device is powering up, the PTP clock needs to be initialized in preparation for
synchronizing to the master clock. The suggested order of tasks is to reset the PTP 1588 clock (RESET_PTP_CLK =
“0”), load the PTP 1588 clock (PTP_LOAD_CLK = “1”) with a value then enable the PTP 1588 clock (EN_PTP_CLK =
“1”). During the initial synchronization attempt, the system time clock may be a little far apart from the PTP master clock,
so it most likely will require a step-time adjustment to get it closer. After that, the continuous time adjustment method or
temporary time adjustment method may be the best options when the system time clock is close to being synchronized
with the master clock.
More details on the 1588 PTP system time clock controls and functions can be found in the register descriptions for
registers 0x600 to 0x617.
3.4.6
IEEE 1588 PTP MESSAGE PROCESSING
The KSZ8463 supports IEEE 1588 PTP time synchronization when 1588 PTP mode and message detection are
enabled in the PTP_MSG_CFG_1 register (0x620 – 0x621). Different operations will be applied to PTP packet processing based on the setting of P2P or E2E in transparent clock mode for port 1 and port 2, master or slave in ordinary clock
mode for port 3 (host port), one-step or two-step clock mode, and if the domain checking is enabled. For the IPv4/UDP
egress packet, the checksum can be updated by either re-calculating the two-bytes or by setting it to zero. For the IPv6/
UDP egress packet, the checksum is always updated. All these 1588 PTP configuration bits are in the PTP_MSG_CFG_1/2 registers (0x620 – 0x623).
For a more detailed description of the 1588 PTP message processing control and function, please refer to the register
descriptions in the register map at locations 0x620 to 0x68F.
3.4.6.1
IEEE 1588 PTP Ingress Packet Processing
The KSZ8463 can detect all IEEE 802.3 Ethernet 1588 PTP packets, IPv4/UDP 1588 PTP packets, and IPv6/UDP 1588
PTP packets by enabling these features in the PTP_MSG_CFG_1 register (0x620 – 0x621). Upon detection of receiving
a 1588 PTP packet, the device will capture the receive time stamp at the time when the start-of-frame delimiter (SFD)
is detected. Adjusting the receive time stamp with the receive latency or asymmetric delay is the responsibility of the
software. The hardware only takes these values into consideration when it updates the correction field in the PTP message header. Likewise, the software needs to adjust the transmit time stamp with the transmit latency. Both the ingress
time stamp and the ingress port number will be embedded in the reserved fields of the 1588 PTP header. The embedded
information will be used by the host to designate the destination port in the response egress packet, identify the direction
of the master port, and to calculate the link delay and offset.
The 1588 PTP packet will be discarded if the 1588 PTP domain field does not match the domain number in the PTP_DOMAIN_VER register (0x624 – 0x625) or if the 1588 PTP version number does not match version number (either 1 or 2)
in the PTP_DOMAIN_VER register (0x624 – 0x625). Packets with a version number of one will always be forwarded to
port 1 or port 2, and not to port 3.
The 1588 PTP packets that are not associated with packet messages in pairs (Pdelay_ Req with Pdelay_Resp, Sync
with Follow_Up, Delay_Req with Delay_Resp) can be filtered and not forwarded to port 3 if the corresponding enable
bits are set in the PTP_MSG_CFG_2 register (0x0622 – 0x623). The 1588 PTP version-1 packet will be forwarded without being modified.
3.4.6.2
IEEE 1588 PTP Egress Packet Processing
The ingress time stamp, the transport type of the 1588 PTP packet, the packet type (tagged or untagged), and the type
of correction field update on the egress side are in the frame header and are accessible for modification by the egress
logic in local switch packet memory. The 1588 PTP packet will be put in the egress queue of highest priority. From the
1588 PTP frame header inside the switch packet memory, the egress logic will get the correction field update instruction.
The residence time, link delay in the PTP_P1/2_LINK_DLY registers (0x646 – 0x647 and 0x666 – 0x667) or turn-around
time might be added to the correction field depending upon the type of 1588 PTP egress packet. The 1588 PTP packet
received from port 3 (host port) has the destination port information to forward as well as the time stamp information that
will be used for updating the correction field in one-step clock operation.
This embedded information (in the reserved fields of 1588 PTP frame header) will be zeroed out before the egress
packet is sent out to conform to the 1588 PTP standard.
DS00002642A-page 36
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
For one-step operation, the original time stamp will be inserted into the sync packet. The egress time stamp of the Sync
packet will be latched in the P1/2_SYNC_TS registers (0x64C – 0x64F and 0x66C – 0x66F), the egress time stamps of
Delay_Req, Pdelay_Req and Pdelay_Resp will be latched in the P1/2_XDLY_REQ_TS (0x648 – 0x64B and 0x668 –
0x6B) and P1/2_PDLY_RESP_TS registers (0x650 – 0x653 and 0x670 – 0x673). These latched egress time stamps
will generate an interrupt to the host CPU and set the interrupt status bits in the PTP_TS_IS register (0x68C – 0x68D)
if the interrupt enable is set in the PTP_TS_IE register (0x68E – 0x68F). These captured egress time stamps will be
used by the 1588 PTP software for link delay measurement, offset adjustment, and time calculation.
The transmit delay value from the port 1 or port 2 time stamp reference point to the network connection point in the
PTP_P1/2_TX_LATENCY registers (0x640 – 0x643) will be added to these value in the P1/2_SYNC_TS, P1/2_XDLY_REQ_TS and P1/2_PDLY_RESP_TS registers to get the egress time stamp with reference point to the network connection point. For transmit Delay_Req or Pdelay_Req packets, the value in the PTP_P1/2_ASYM_COR registers
(0x644 – 0x645 and 0x664 – 0x665) will be subtracted from the correction field.
3.4.7
IEEE 1588 PTP EVENT TRIGGERING AND TIME STAMPING
An event trigger output signal can be generated when the target and activation time matches the IEEE 1588 PTP system
clock time. Likewise, an event time stamp input can be captured from an external event input signal and the corresponding time on the IEEE 1588 PTP system clock will be captured.
Up to 12 GPIO pins can be configured as either output signal when trigger target time is matching IEEE 1588 PTP system clock time or monitoring input signal for external event time stamp. All event trigger outputs are generated by comparing the system clock time with trigger target time continuously to make sure time synchronization is always on-going.
3.4.7.1
IEEE 1588 PTP Trigger Output
The KSZ8463 supports up to 12 event trigger units which can output to any one of the 12 GPIO pins by setting bits[3:0]
in TRIG[1:12]_CFG_1 registers. Multiple trigger units can be assigned to a single GPIO pin at the same time as logical
OR’ed function allowing generation of more complex waveforms. Also multiple trigger units can be cascaded (one Unit
only at any time) to drive a single GPIO pin to generate a long and repeatable bit sequence. Each trigger unit that is
cascaded can be any signal type (edge, pulse, periodic, register-bits, and clock output).
Each trigger unit can be programmed to generate one time rising or falling edge (toggle mode), a single positive or negative pulse of programmable width, a periodic signal of programmable width, cycle time, bit-patterns to shift out from
TRIG[1:12]_CFG_[1:8] registers, and each trigger Unit can be programmed to generate interrupt of trigger output Unit
done and status in PTP_TRIG_IE/IS registers. For each trigger Unit, the host CPU programs the desired output waveform, GPIO pins, target time in TRIG[1:12]_TGT_NS and TRIG[1:12]_TGT_S registers that the activity is to occur, and
enable the trigger output Unit in TRIG_EN register, then the trigger output signal will be generated on the GPIO pin when
the internal IEEE 1588 PTP system time matches the desired target time. The device can be programmed to generate
a pulse-per-second (PPS) output signal. The maximum trigger output signal frequency is up to 12.5 MHz.
For a more detailed description of the 1588 PTP event trigger output control, configuration and function, please refer to
the registers description in the register map from 0x200 to 0x397 locations.
3.4.7.2
IEEE 1588 PTP Event Time Stamp Input
External event inputs on the GPIO pins can be monitored and time stamped with the resolution of 8 ns. The external
signal event can be monitored and detected as either rising edge, falling edge, positive pulse, or negative pulse by setting bits[7:6] in TS[1:12]_CFG registers. Multiple time stamp units can be cascaded or chained together to associate
with a single GPIO pin to detect a series of events. When event is detected, the time stamp will be captured in three
fields: 32-bit second field in TS[1:12]_SMPL1/2_SH/L registers, 30-bit nanosecond field in TS[1:12]_SMPL1/2_NSH/L
registers, and 3-bit phase field in TS[1:12]_SMPL1/2_SUB_NS registers. Second and nanosecond fields are updated
every 25 MHz clock cycle. The 3-bit phase field is updated every 125 MHz clock cycle and indicates one of the five 8 ns/
125 MHz clock cycles. The bit [14] in TS[1:12]_SMPL1/2_NSH registers indicates the event time stamp input is either
falling edge or rising edge.
The KSZ8463 supports up to twelve time stamp input units which can input from any one of the twelve GPIO pins by
setting bits[11:8] in TS[1:12]_CFG registers. The enable bits [11:0] in TS_EN register are used to enable the time stamp
units. The last time stamp unit (Unit 12) can support up to eight time stamps for multiple event detection and up to four
pulses can be detected. The rest of the units (units 1 through 11) have two time stamps to support single edge or pulse
detection. Pulse width can be measured by the time difference between consecutive time stamps. When an input event
is detected, one of the bits [11:0] in TS_RDY register is asserted and will generate a time stamp interrupt if the
PTP_TS_IE bit is set. The host CPU is also expected to read the time stamp status in the TS[1:12]_STATUS registers
to report the number of detected event (either rising or falling edge) counts and overflow. In single mode, it can detect
2018 Microchip Technology Inc.
DS00002642A-page 37
KSZ8463ML/RL/FML/FRL
up to fifteen events at any single Unit. In cascade mode, it can detect up to two events at units 1 through 11 or up to
eight events at Unit 12, and it can detect up to fifteen events for any unit as a tail unit. Pulses or edges can be detected
up to 25 MHz.
For more details on 1588 PTP event time stamp input control, configuration and function, please refer to the register
descriptions for locations 0x400 to 0x5FD in the register map.
3.4.7.3
IEEE 1588 PTP Event Interrupts
All IEEE 1588 PTP event trigger and time stamp interrupts are located in the PTP_TRIG_IE/PTP_TS_IE enable registers and the PTP_TRIG_IS/PTP_TS_IS status registers. These interrupts are fully maskable via their respective enable
bits and shared with other interrupts that use the INTRN interrupt pin.
These twelve event trigger output status interrupts are logical OR’ed together and connected to bit[10] in the ISR register.
These twelve event trigger output enable interrupts are logical OR’ed together and connected to bit[10] in the IER register.
These twelve time stamp status interrupts are logical OR’ed together with the rest of bits in this register and the logical
OR’ed output is connected to bit[12] in the ISR register.
These twelve time stamp enable interrupts are logical OR’ed together with the rest of bits in this register and the logical
OR’ed output is connected to bit[12] in the IER register.
3.4.7.4
IEEE 1588 GPIO
The KSZ8463 supports twelve GPIO pins that can be used for general I/O or can be configured to utilize the timing of
the IEEE 1588 protocol. These GPIO pins can be used for input event monitoring, outputting pulses, outputting clocks,
or outputting unique serial bit streams. The GPIO output pins can be configured to initiate their output upon the occurrence of a specific time which is being kept by the onboard precision time clock. Likewise, the specific time of arrival of
an input event can be captured and recorded with respect to the precision time clock. Refer to the General Purpose and
IEEE 1588 Input/Output (GPIO) section for details on the operation of the GPIO pins.
3.5
3.5.1
General Purpose and IEEE 1588 Input/Output (GPIO)
OVERVIEW
The KSZ8463 devices incorporate a set of general purpose input/output (GPIO) pins that are configurable to meet the
needs of many applications. The input and output signals on the GPIO pins can be directly controlled via a local processor or they can be set up to work closely with the IEEE 1588 protocol to create and/or monitor precisely timed signals
which are synchronous to the precision time clock. Some GPIO pins are dedicated, while others are dual function pins.
Dual function pins are managed by the IOMXSEL register. Table 3-6 provides a convenient summary of available GPIO
resources in the KSZ8463 devices.
TABLE 3-6:
GPIO PIN REFERENCE
KSZ8463ML and KSZ8463FML
KSZ8463RL and KSZ8463FRL
GPIO
Pin Number
Function
GPIO
Pin Number
Function
GPIO_0
48
GPIO0
GPIO_0
48
GPIO0
GPIO_1
49
GPIO1
GPIO_1
49
GPIO1
GPIO_2
52
GPIO2
GPIO_2
52
GPIO2
GPIO_3
53
GPIO3
GPIO_3
53
GPIO3
GPIO_4
54
GPIO4
GPIO_4
54
GPIO4
GPIO_5
55
GPIO5
GPIO_5
55
GPIO5
GPIO_6
58
GPIO6
GPIO_6
58
GPIO6
GPIO_7
59
P1LED1/
GPIO7_MLI
GPIO_7
38
GPIO7_RLI
GPIO_8
46
GPIO8
GPIO_8
46
GPIO8
GPIO_9
61
P2LED1/
GPIO9_MLI
GPIO_9
36
GPIO9_RLI
DS00002642A-page 38
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 3-6:
GPIO PIN REFERENCE (CONTINUED)
KSZ8463ML and KSZ8463FML
KSZ8463RL and KSZ8463FRL
GPIO
Pin Number
Function
GPIO
Pin Number
Function
GPIO_10
62
P2LED0/
GPIO10_MLI
GPIO_10
37
GPIO10_RLI
GPIO_11
47
GPIO11
GPIO_11
47
GPIO11
3.5.2
GPIO PIN FUNCTIONALITY CONTROL
The GPIO_OEN register is used to configure each GPIO as an input or an output. Each GPIO pin has a set of registers
associated with it that are configured to determine its functionality, and any relationship it has with other GPIO pins or
registers. Each GPIO pin can be configured to output a binary signal state or a serial sequence of bits. Each GPIO pin
can output a single serial bit pattern or it can be programmed to continuously loop and output the pattern until stopped.
The duration of the high and low periods within the sequential bit patterns can be programmed to meet the requirements
of the application. The output can be triggered to occur at any time by the local processor writing to the correct register
or it can be triggered by the local IEEE precision timing protocol clock being equal to an exact time. The local processor
can interrogate any GPIO pin at any time or the value of the IEEE precision time protocol clock can be captured and
recorded when the specified event occurs on any of the GPIO pins. The control and output of the GPIO pins can be
cascaded to create complex digital output sequences and waveforms. Lastly, the units can be programmed to generate
an interrupt on specific conditions.
The control structure for the twelve GPIO pins are organized into two separate units called the trigger output units (TOU)
and the time stamp input units (TSU). There are twelve TOUs and twelve TSUs which can be used with any of the GPIO
pins. There are 32 control bytes for each of the two units to control the functionality. The depth of control is summarized
in Table 3-7.
TABLE 3-7:
TRIGGER OUTPUT UNITS AND TIME STAMP INPUT UNITS SUMMARY
Trigger Output Units
Time Stamp Input Units
32 Bytes of Parameters
32 Bytes of Parameters
Trigger Patterns:
Negative Edge, Positive Edge, Negative Pulse, Positive Pulse, Negative Period, Positive Period, Register
Output Shift
Detection:
Negative or Positive Edges
Negative or Positive Pulses
Pulse Width:
16-Bit Counter @ 8 ns Each (524288 ns, maximum)
Two Edge/One Pulse (Two Time Stamps) Detection
Capability (time stamp Units 10:0)
Cycle Width:
Eight Edge/Four Pulse (Eight Time Stamps) Detection (time
32-Bit Counter @ 1 ns Each (4.29 seconds, maximum)
stamp Unit 11)
Cycle Count:
16-Bit Counter (0 = Infinite Loop)
Cascadable to Detect Multiple Edges
Total Cascade Mode Cycle Time:
32-Bit Counter @ 1 ns Each
—
Shift Register:
16-Bits (only for register shift output mode)
—
Cascadable to Generate Complex Waveforms
—
3.5.3
GPIO PIN CONTROL REGISTER LAYOUT
Most of the registers used to control the time stamp units and the trigger output units are duplicated for each GPIO pin.
There are a few registers which are associated with all the overall functionality of all the GPIO pins or only specific GPIO
pins. These are summarized in Table 3-8.
TABLE 3-8:
GPIO REGISTERS AFFECTING EITHER ALL OR SPECIFIC UNITS
Register Name
Register Location
Related to Which Trigger Output Units
or Time Stamping Units
Trigger Error Register – TRIG_ERR
0x200 – 0x201
All trigger output units.
Trigger Active Register – TRIG_ACTIVE
0x202 – 0x203
All trigger output units.
2018 Microchip Technology Inc.
DS00002642A-page 39
KSZ8463ML/RL/FML/FRL
TABLE 3-8:
GPIO REGISTERS AFFECTING EITHER ALL OR SPECIFIC UNITS (CONTINUED)
Register Name
Register Location
Related to Which Trigger Output Units
or Time Stamping Units
Trigger Done Register – TRIG_DONE
0x204 – 0x205
All trigger output units.
Trigger Enable Register – TRIG_EN
0x206 – 0x207
All trigger output units.
Trigger SW Reset Register – TRIG_SW_RST
0x208 – 0x209
All trigger output units.
Trigger Unit 12 Output PPS
Pulse-Width Register –
TRIG12_PPS_WIDTH
0x20A – 0x20B
Trigger output Unit 1, 12.
Time Stamp Ready Register – TS_RDY
0x400 – 0x401
All trigger output units.
Time Stamp Enable Register – TS_EN
0x402 – 0x403
All trigger output units.
Time Stamp Software Reset Register –
TS_SW_RST
0x404 – 0x405
All trigger output units.
FIGURE 3-10:
TRIGGER OUTPUT UNIT ORGANIZATION AND ASSOCIATED REGISTERS
PTP CLOCK
= COMPARE [S, nS]
= COMPARE [S, nS]
TRIG1_TGT_NSL, TRIG1_TGT_NSH,
TRIG1_TGT_SL, TRIG1_TGT_SH
TRIGGER TIME
TRIGGER TIME
CONTROL
CONTROL
125MHz CLK CYCLE, PULSE PARAMETERS
COUNTERS
DATA SHIFT REGISTER
GPIO_OEN[x]
GPIO_X
TRIGGER OUTPUT UNIT X
DS00002642A-page 40
TRIG1_CFG_[8:1]
125MHz CLK CYCLE, PULSE PARAMETERS
COUNTERS
DATA SHIFT REGISTER
TRIG1_CFG[6]
GPIO_OEN[0]
GPIO_1
ASSOCIATED REGISTERS
TRIGGER OUTPUT UNIT 1
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
FIGURE 3-11:
3.5.4
TIME STAMP INPUT UNIT ORGANIZATION AND ASSOCIATED REGISTERS
GPIO TRIGGER OUTPUT UNIT AND TIME STAMP UNIT INTERRUPTS
The trigger output units and the time stamp units can be programmed to generate interrupts when specified events
occur. The interrupt control structure is shown in Figure 3-12 and Figure 3-13.
FIGURE 3-12:
TRIGGER UNIT INTERRUPTS
IER
ISR
INT
BIT 10
12
BIT 10
TRIG_ERR[11:0]
12
PTP_TRIG_IE[11:0]
TRIG_EN[11:0]
12
TRIG_DONE[11:0]
12
12
TRIG_NOTIFY[11:0]
PTP_TRIG_IS[11:0]
2018 Microchip Technology Inc.
DS00002642A-page 41
KSZ8463ML/RL/FML/FRL
FIGURE 3-13:
3.6
TIME STAMP UNIT INTERRUPTS
Using the GPIO Pins with the Trigger Output Units
The twelve trigger output units (TOU) can be used to generate a variety of pulses, clocks, waveforms, and data streams
at user-selectable GPIO pins. The TOUs will generate the user-specified output starting at a specific time with respect
to the IEEE 1588 precision time clock. This section provides some information on configuring the TOUs to generate
specific types of output. In the information below, the value “x” represents one of the twelve TOUs. Because this area
of the device is very flexible and powerful, please reference application note ANLAN203, KSZ84xx GPIO Pin Output
Functionality, for additional information on creating specific types of waveforms and utilizing this feature.
When using a single TOU to control multiple GPIO pins, there are several details of functionality that must be taken into
account. When switching between GPIO pins, the output value on those pins can be affected. If a TOU changes the
GPIO pin level to a high value, writing to this units configuration register to change the addressed GPIO pin to a different
one will cause the hardware to drop the level in the previous GPIO pin and set the new GPIO pin to a high value. To
prevent the second GPIO pin from going high immediately, the TOU must be reset prior to programming in a different
GPIO pin value.
3.6.1
CREATING A LOW-GOING PULSE AT A SPECIFIC TIME
• Specifying the Time
The desired trigger time will be set in TRIGx_TGT_NSH, TRIGx_TGT_NSL, TRIGx_TGT_SH, and TRIGx_TGT_SL registers.
• Specifying the Pulse Parameters
TRIGx_CFG_1[6:4] = “010” for negative pulse generation.
TRIGx_CFG_2[15:0] = Pulse width where each Unit is 8 ns.
• Associate this Trigger Output Unit to a Specific GPIO Pin
TRIGx_CFG_1[3:0] = Selects GPIO pin to use.
• Set Up Interrupts, if Needed
If it is desired to get notification that the trigger output event occurred set up the following registers.
TRIGx_CFG_1, bit[8] (Trigger Notify) = “1” is one requirement for enabling interrupt on done or error.
Set the corresponding trigger Unit interrupt enable bit in the PTP_TRIG_IE register.
DS00002642A-page 42
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
• Enabling the Trigger Output Unit
Set the corresponding trigger Unit enable bit in the TRIG_EN register.
Be aware that for a low-going pulse in non-cascaded mode (single mode), the output will be driven by the unit to a high
level when the trigger unit is enabled. In cascade mode, the output will be driven by the unit to the high state 8 ns prior
to the programmed trigger time.
3.6.2
CREATING A HIGH-GOING PULSE AT A SPECIFIC TIME
• Specifying the Time
The desired trigger time will be set in TRIGx_TGT_NSH, TRIGx_TGT_NSL, TRIGx_TGT_SH, and TRIGx_TGT_SL registers.
• Specifying the Pulse Parameters
TRIGx_CFG_1[6:4] = “011” for positive pulse generation.
TRIGx_CFG_2[15:0] = Pulse width where each Unit is 8 ns.
• Associate this Trigger Output Unit to a Specific GPIO Pin
TRIGx_CFG_1[3:0] = Selects GPIO pin to use.
• Set Up Interrupts if Needed
If it is desired to get notification that the trigger output event occurred set up the following registers.
TRIGx_CFG_1, bit[8] (Trigger Notify) = “1” is one requirement for enabling interrupt on done or error.
Set the corresponding trigger Unit interrupt enable bit in the PTP_TRIG_IE register.
• Enabling the Trigger Output Unit
Set the corresponding trigger Unit enable bit in the TRIG_EN register.
Be aware that for a high-going pulse in non-cascaded mode (single mode), the output will be driven by the unit to a low
level when the trigger unit is enabled. In cascade mode, the output will be driven by the unit to the low state 8 ns prior
to the programmed trigger time.
3.6.3
CREATING A FREE RUNNING CLOCK SOURCE
• Specifying the Time
Typically there is no need to set up a desired trigger time with respect to a free running clock. There are two ways that
the free running clock can be started.
Set up a desired trigger time in the TRIGx_TGT_NSH, TRIGx_TGT_NSL, TRIGx_TGT_SH, and TRIGx_TGT_SL registers.
After parameters have been set up, start the clock by setting the Trigger Now bit, bit[9], in the TRIGx_CFG_1 register.
• Specifying the Clock Parameters
TRIGx_CFG_1[6:4] = “101” for generating a positive periodic signal.
High part of cycle defined by bits[15:0] in the TRIGx_CFG_2 register. Each Unit is 8 ns.
Cycle width defined by bits[15:0] in TRIGx_CFG_3 and TRIGx_CFG_4 registers. Each Unit is 1 ns.
Continuous clock by setting TRIGx_CFG_5, bits[15:0] = “0”.
• Associate this Trigger Output Unit to a Specific GPIO Pin
TRIGx_CFG_1[3:0] = Selects GPIO pin to use.
• Set Up Interrupts if Needed
If it is desired to get notification that the trigger output event occurred set up the following registers.
TRIGx_CFG_1, bit[8] (Trigger Notify) = “1” is one requirement for enabling interrupt on done or error.
Set the corresponding trigger Unit interrupt enable bit in the PTP_TRIG_IE register.
• Enabling the Trigger Output Unit
Set the corresponding trigger Unit enable bit in the TRIG_EN register.
2018 Microchip Technology Inc.
DS00002642A-page 43
KSZ8463ML/RL/FML/FRL
Because the frequencies to be generated are based on the period of the 125 MHz clock, there are some limitations that
the user must be aware of. Certain frequencies can be created with unvarying duty cycles. However, other frequencies
may incur some variation in duty cycle. There are methods of utilizing the trigger Unit 2 clock edge output select bit (bit[7]
in of Reg. 0x248 – 0x249) and GPIO1 to control and minimize the variances.
3.6.4
CREATING FINITE LENGTH PERIODIC BIT STREAMS AT A SPECIFIC TIME
This example implies that a uniform clock will be generated for a specific number of clock cycles:
• Specifying the Time
The desired trigger time will be set in TRIGx_TGT_NSH, TRIGx_TGT_NSL, TRIGx_TGT_SH, and TRIGx_TGT_SL registers.
• Specifying the Finite Length Periodic Bit Stream Parameters
TRIGx_CFG_1[6:4] = “101” for generating a positive periodic signal.
High part of cycle defined by bits[15:0] in the TRIGx_CFG_2 register. Each Unit is 8 ns.
Cycle width defined by bits[15:0] in TRIGx_CFG_3 and TRIGx_CFG_4 registers. Each Unit is 1 ns.
Finite length count established by setting TRIGx_CFG_5, bits[15:0] = “number of cycles”. Each Unit is one cycle.
• Associate this Trigger Output Unit to a Specific GPIO Pin
TRIGx_CFG_1[3:0] = Selects GPIO pin to use.
• Set Up Interrupts if Needed
If it is desired to get notification that the trigger output event occurred, set up the following registers.
TRIGx_CFG_1, bit[8] (Trigger Notify) = “1” is one requirement for enabling interrupt on done or error.
Set the corresponding trigger Unit interrupt enable bit in the PTP_TRIG_IE register.
• Enabling the Trigger Output Unit
Set the corresponding Trigger Unit Enable bit in the TRIG_EN register.
3.6.5
CREATING FINITE LENGTH NON-UNIFORM BIT STREAMS AT A SPECIFIC TIME
Generation of a finite length non-uniform waveform which is a multiple of the bit pattern stored in the data storage register.
• Specifying the Time
The desired trigger time will be set in TRIGx_TGT_NSH, TRIGx_TGT_NSL, TRIGx_TGT_SH, and TRIGx_TGT_SL registers.
• Specifying the Finite Length Non-Uniform Bit Stream Parameters
TRIGx_CFG_1[6:4] = “110” for generating signal based on contents of data register.
16-bit pattern stored in TRIGx_CFG_6 register.
Bit width defined by bits[15:0] in TRIGx_CFG_3 and TRIGx_CFG_4 registers. Each Unit is 1 ns.
Bit length of finite pattern is established by shifting the data register “N” times. Set TRIGx_CFG_5, bits[15:0] = “N”.
• Associate this Trigger Output Unit to a Specific GPIO Pin
TRIGx_CFG_1[3:0] = Selects GPIO pin to use.
• Set up Interrupts if Needed
If it is desired to get notification that the trigger output event occurred, set up the following registers.
TRIGx_CFG_1, bit[8] (Trigger Notify) = “1” is one requirement for enabling interrupt on done or error.
Set the corresponding trigger unit interrupt enable bit in the PTP_TRIG_IE register.
• Enabling the Trigger Output Unit
Set the corresponding trigger unit enable bit in the TRIG_EN register.
3.6.6
CREATING COMPLEX WAVEFORMS AT A SPECIFIC TIME
Complex waveforms can be created by combining the various functions available in the trigger output units using a
method called “cascading.”
DS00002642A-page 44
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
Figure 3-14 illustrates the generation of a complex waveform onto one GPIO pin. Trigger output Unit 1 (TOU1) and trigger output Unit 2 (TOU2) are cascaded to produce the complex waveform. Cascading allows multiple outputs to be
sequentially output onto one GPIO pin. In Figure 3-14, the waveform created by TOU1 is output first on the selected
GPIO pin when the indicated TOU1 trigger time is reached. The value in TRIG1_CFG7 and TRIG1_CFG8 will be added
to the TOU1 trigger time and the next TOU1 output will occur at that time. Meanwhile, TOU2, will operate in the same
manner; outputting its waveform at TOU2 trigger time and then outputting again at a time TRIG2_CFG7 and
TRIG2_CFG8 later. The TRIGx_CFG7 and 8 register values must be the same for all TOUs that are cascaded together.
The number of times TOU1 and TOU2 will be output will depend on the cycle times programmed into the TRIG1_CFG6
and TRIG2_CFG6 registers. Care must be taken to select the correct values so as to avoid erroneous overlap.
Additional steps are required in setting up cascaded TOUs:
• Specifying which trigger output Unit in the cascade is the last Unit called the tail unit.
• The last trigger output Unit in a cascade setup should have its tail bit set to “1”.
FIGURE 3-14:
COMPLEX WAVEFORM GENERATION USING CASCADE MODE
DEFINE CX FOR TOU1
DEFINE DX FOR TOU2
TRIG1_CFG_1 = TRIGGER EVENT PATTERN
TRIG1_CFG_2 = OUTPUT PULSE WIDTH
TRIG1_CFG_3 = OUTPUT CYCLE WIDTH (LOW)
TRIG1_CFG_4 = OUTPUT CYCLE WIDTH (HIGH)
TRIG1_CFG_5 = # CYCLE OUTPUT
TRIG2_CFG_1 = TRIGGER EVENT PATTERN
TRIG2_CFG_2 = OUTPUT PULSE WIDTH
TRIG2_CFG_3 = OUTPUT CYCLE WIDTH (LOW)
TRIG2_CFG_4 = OUTPUT CYCLE WIDTH (HIGH)
TRIG2_CFG_5 = # CYCLE OUTPUT
CX =
C 0 C1 C2 C3 C4
TOU1
OUTPUT #1
TOU1
TRIGGER
TIME #1
DX =
D0 D1 D2
TOU2
OUTPUT #1
C 0 C1 C2 C3 C4
TOU1
OUTPUT #2
TOU1
TRIGGER
TIME #2
TOU2
TRIGGER
TIME #1
D0 D1 D2
GPIO
OUTPUT
TOU2
OUTPUT #2
TOU2
TRIGGER
TIME #2
VALUE IN
TRIG1_CFG_7
VALUE IN
TRIG2_CFG_7
TRIG1_CFG_6 = # TIMES TOU1 OUTPUT TO OCCUR
TRIG2_CFG_6 = # TIMES TOU2 OUTPUT TO OCCUR
TOU1 TRIGGER TIMEN-1 = TOU1 TRIGGER TIMEN + (TRIG1_CFG_7, 8)
TOU2 TRIGGER TIMEN-1 = TOU2 TRIGGER TIMEN + (TRIG2_CFG_7, 8)
2018 Microchip Technology Inc.
DS00002642A-page 45
KSZ8463ML/RL/FML/FRL
3.7
Using the GPIO Pins with the Time Stamp Input Units
The twelve time stamp input units (TSU) can be set up to capture a variety of inputs at user selectable GPIO pins. The
current time of the precision time clock time will be captured and stored at the time in which the input event occurs. This
section provides some information on configuring the time stamp input units. In the information below, the value “x” represents one of the twelve time stamp input units. Because this area of the device is very flexible and powerful, it is
advised that you contact your Microchip representative for additional information on capturing specific types of waveforms and utilizing this feature.
• Time Stamp Value
Each time stamp input nit can capture two sampled values of time stamps. These first two values remain until read, even
if more events occur. The time stamp value captured consists of three parts which are latched in three registers.
Sample #1, the seconds value; TSx_SMPL1_SH, TSx_SMPL1_SL
Sample #1, the nanoseconds value; TSx_SMPL1_NSH, TSx_SMPL1_NSL
Sample #1, the sub-nanoseconds value; TSx_SMPL1_SUB_NS
Sample #2, the seconds value; TSx_SMPL2_SH, TSx_SMPL2_SL
Sample #2, the nanoseconds value; TSx_SMPL2_NSH, TSx_SMPL2_NSL
Sample #2, the sub-nanoseconds value; TSx_SMPL2_SUB_NS
The actual value in TSx_SMPL1/2_SUB_NS is a binary value of 0 through 4 which indicates 0 ns, 8 ns, 16 ns, 24 ns,
or 32 ns. Note that the processor needs to add this value to the seconds and nanoseconds value to get the closest true
value of the time stamp event.
• Number of Time Stamps Available
Each time stamp input unit can capture two events or two time stamps values. Note that the exception to this is TSU12.
TSU12 can capture eight events and thus has eight sample time registers (SMPL1 thru SMPL8) allowing for more robust
timing acquisition in one TSU. Note that the amount of samples for any given GPIO pin can be increased by cascading
time stamp unit. When TSUs are cascaded, the incoming events are routed to a sequentially established order of TSUs
for capture. For example, you can cascade TSU12, and TSU 1-4 to be able to capture twelve time stamps off of one
GPIO pin. Cascading is set up in the TSx_CFG registers.
• Events that can be Captured
The time stamp input units can capture rising edges and falling edges. In this case, the time stamp of the event will be
captured in the Sample #1 time stamp registers. A pulse can be captured if rising edge detection is combined with falling
edge detection. In this case, one edge will be captured in the Sample #1 time stamp registers and the other edge will
be captured in the Sample #2 time stamp registers. This functionality is programmed in the TSx_CFG register for each
time stamp unit.
time stamping an incoming low-going edge:
• Specifying the Edge Parameters
TSx_CFG bit[6] = “1”
• Associate this Time Stamp Unit to a Specific GPIO Pin
TSx_CFG bits[11:8] = Selected GPIO Pin #
• Set Up Interrupts if Needed
Set the corresponding time stamp unit interrupt enable bit in the PTP_TS_IE register.
• Enabling the Time Stamp Unit
Set the corresponding time stamp unit enable bit in the TS_EN register.
Time stamping an incoming high-going edge:
• Specifying the Edge Parameters
TSx_CFG bit[7] = “1”
• Associate this Time Stamp Unit to a Specific GPIO Pin
TSx_CFG bits[11:8] = Selected GPIO Pin #
• Set Up Interrupts if Needed
Set the corresponding time stamp unit interrupt enable bit in the PTP_TS_IE register.
DS00002642A-page 46
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
• Enabling the Time Stamp Unit
Set the corresponding time stamp unit enable bit in the TS_EN register.
Time stamping an incoming low-going pulse or high-going pulse
• Specifying the Edge Parameters
TSx_CFG bit[7] = “1”
TSx_CFG bit[6] = “1”
• Associate this Time Stamp Unit to a Specific GPIO Pin
TSx_CFG bits[11:8] = Selected GPIO Pin #
• Set Up Interrupts if Needed
Set the corresponding time stamp unit interrupt enable bit in the PTP_TS_IE register.
• Enabling the Time Stamp Unit
Set the corresponding time stamp unit enable bit in the TS_EN register.
3.8
Device Clocks
A 25 MHz clock source on X1/X2 is required for MII operation. The RMII 50 MHz clock can either be derived from the
25 MHz X1/X2 reference, or is received from an external source. If an external 50 MHz clock is used for RMII, then a
local 25 MHz crystal or clock oscillator is not required. There are a number of pins with clock related functions on this
device. Table 3-9 summarizes those pins and the area of usage and if they are related to 25 MHz, 50 MHz, RMII, or MII
clocking.
TABLE 3-9:
Clock Signal
Name
DEVICE CLOCKS AND RELATED PINS
Pin Number
Usage
Strapping Option Information
The X1 and X2 pins are used to input a
clock which is used to clock all of the
circuits within the device.
MII – Clocking Choices:
• 25 MHz crystal connected
between X1, X2
• 25 MHz oscillator connected to
pin X1 only. X2 shall be unconnected.
X1, X2
18, 19
RMII – Clocking Choices:
• Either connection specified above
for X1 and X2 with other control
bits and pins configured as specified in Table 3-17 to produce the
required 50 MHz output on REFCLK_O. REFCLK_O externally
connected to REFCLK_I.
• 50MHz supplied on REFCLK_I
pin from external source. X1 and
X2 unconnected. Other control
bits and pins configured as specified in Table 3-17.
The SPI_DO pin (pin 41) is used to
select if a 25 MHz clock on the X1 and
X2 pins or a 50 MHz clock on the REFCLK_I pin will be used as the source of
all RMII clocking.
Other control bits and control pins are
used to determine other attributes of
the RMII/MII clocking scheme.
Refer to Table 3-17 for more information on the control bits and pins.
Refer to Table 2-2.
Refer also to X1, X2 pin descriptions.
2018 Microchip Technology Inc.
DS00002642A-page 47
KSZ8463ML/RL/FML/FRL
TABLE 3-9:
DEVICE CLOCKS AND RELATED PINS (CONTINUED)
Clock Signal
Name
Pin Number
TX_CLK/
REFCLK_I
27
TXD3/
EN_REFCLK_O
23
RXD3/
REFCLK_O
32
RX_CLK/
GPIO7_RLI
38
Usage
These four pins are used for the clocking and configuration of the MII and
RMII interfaces.
MII:
• 25MHz clocks are output on TX_CLK and RX_CLK.
RMII:
• A 50 MHz clock must be received
on REFCLK_I. This comes either
from an external source or via
external connection from REFCLK_O.
Strapping Option Information
The SPI_DO pin (pin 41) is used to
select if a 25 MHz clock on the X1 and
X2 pins or a 50 MHz clock on the REFCLK_I pin will be used as the source of
all RMII clocking.
Other control bits and control pins are
used to determine other attributes of
the RMII/MII clocking scheme.
Refer to Table 3-17 for more information on the control bits and pins.
Refer to Table 2-2.
Refer to Table 3-17 for details on the
usage of these signal pins.
SPI_SCLK/MDC
44
This pin is the clock for the SPI interface.
RXD2
33
This pin determines the clocking range
of the SPI clock. Refer to the Strapping —
Options section.
—
Note that the clock tree power-down control register (0x038 – 0x039): CTPDC is used to power down the clocks in various areas of the device. There are no other internal register bits which control the clock generation or usage in the
device.
3.8.1
GPIO AND IEEE 1588-RELATED CLOCKING
The GPIO and IEEE 1588-related circuits both utilize the 25 MHz clock and the derived 125 MHz clock. The tolerance
and accuracy of the 25 MHz clock source will affect the IEEE 1588 jitter and offset in a system utilizing multiple slave
devices. Therefore, the 25 MHz source should be chosen with care towards the performance of the application in mind.
Using an oscillator will generally provide better results.
3.9
Power
The KSZ8463 device requires a single 3.3V supply to operate. An internal low-voltage LDO provides the necessary low
voltage (nominal ~1.3V) to power the analog and digital logic cores. The various I/Os can be operated at 1.8V, 2.5V, and
3.3V. Table 3-10 illustrates the various voltage options and requirements of the device.
TABLE 3-10:
VOLTAGE OPTIONS AND REQUIREMENTS
Power Signal Name
Device Pin
Requirement
VDD_A3.3
9
VDD_IO
21, 30, 56
Choice of 1.8V or 2.5V or 3.3V for the I/O circuits. These input
power pins power the I/O circuitry of the device. This voltage is
also used as the input to the internal low-voltage regulator.
VDD_AL
6
Filtered low-voltage analog input voltage. This is where the filtered low voltage is fed back into the device to power the analog
block.
VDD_COL
16
Filtered low-voltage AD input voltage. This pin feeds the low voltage to the digital circuits within the analog block.
DS00002642A-page 48
3.3V input power to the analog blocks in the device.
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 3-10:
VOLTAGE OPTIONS AND REQUIREMENTS (CONTINUED)
Power Signal Name
Device Pin
VDD_L
40, 51
Requirement
Output of internal low-voltage LDO regulator. This voltage is
available on these pins to allow connection to external capacitors and ferrite beads for filtering and power integrity. These pins
must be externally connected to pins 6 and 16.
If the internal LDO regulator is turned off, these pins become
power inputs.
AGND
3, 8, 12
Analog Ground.
DGND
20, 29, 39, 50, 57
Digital Ground.
The preferred method of configuring the related low-voltage power pins when using an external low-voltage regulator is
illustrated in Figure 3-15. The number of capacitors, values of capacitors, and exact placement of components will
depend upon the specific design.
FIGURE 3-15:
RECOMMENDED LOW-VOLTAGE POWER CONNECTION USING AN EXTERNAL
LOW-VOLTAGE REGULATOR
3.3VA
9
VDD_A3.3
16 VDD_COL
51 VDD_L
LOW V
C
40 VDD_L
KSZ8463
FB
6
VDD_AL
DGND
C
20, 29, 39,
50, 57
AGND
VDD_IO
3, 6, 12
21, 30, 56
1.8V, 2.5V, 3.3V
3.9.1
INTERNAL LOW VOLTAGE LDO REGULATOR
The KSZ8463 reduces board cost and simplifies board layout by integrating a low noise internal low-voltage LDO regulator to supply the nominal ~1.3V core power voltage for a single 3.3V power supply solution. If it is desired to take
advantage of an external low-voltage supply that is available, the internal low-voltage regulator can be disabled to save
power. The LDO_Off bit, bit[7] in Register 0x748 is used to enable or disable the internal low-voltage regulator. The
default state of the LDO_Off bit is “0” which enables the internal low-voltage regulator. Turning off the internal low-voltage regulator will require software to write a “1” to that control bit. During the time from power up to setting this bit, both
the external voltage supply and the internal regulator will be supplying power. Note that it is not necessary to turn off the
internal low-voltage regulator. No damage will occur if it is left on. However, leaving it on will result in less than optimized
power consumption.
2018 Microchip Technology Inc.
DS00002642A-page 49
KSZ8463ML/RL/FML/FRL
The internal regulator takes its power from VDD_IO, and functions best when VDD_IO is 3.3V or 2.5V. If VDD_IO is
1.8V, the output voltage will be somewhat decreased. For optimal performance, an external power supply, in place of
the internal regulator, is recommended when VDD_IO is 1.8V.
The preferred method of configuring the low-voltage related power pins for using the internal low-voltage regulator is
illustrated in Figure 3-16. The output of the internal regulator is available on pins 40 and 51 and is filtered using external
capacitors and a ferrite bead to supply power to pins 6 and 16. The number of capacitors, values of capacitors, and
exact placement of components will depend upon the specific design.
FIGURE 3-16:
RECOMMENDED LOW-VOLTAGE POWER CONNECTION USING THE INTERNAL
LOW-VOLTAGE REGULATOR
3.3VA
9
VDD_A3.3
16 VDD_COL
51 VDD_L
40 VDD_L
C
KSZ8463
FB
6
VDD_AL
DGND
C
20, 29, 39,
50, 57
AGND
VDD_IO
3, 6, 12
21, 30, 56
1.8V, 2.5V, 3.3V
3.10
Power Management
The KSZ8463 supports enhanced power management features in low-power state with energy detection to ensure lowpower dissipation during device idle periods. There are three operation modes under the power management function
which is controlled by two bits in the power management control and wake-up event status register (PMCTRL, 0x032 –
0x033) as shown below:
• PMCTRL[1:0] = “00” Normal Operation Mode
• PMCTRL[1:0] = “01” Energy Detect Mode
• PMCTRL[1:0] = “10” Global Soft Power-Down Mode
The Table 3-11 indicates all internal function blocks status under three different power-management operation modes.
TABLE 3-11:
POWER MANAGEMENT AND INTERNAL BLOCKS
Power Management Operation Modes
KSZ8463 Function Blocks
Normal Mode
Energy Detect Mode
Soft Power-Down Mode
Enabled
Disabled
Disabled
Tx/Rx PHYs
Enabled
Energy Detect at Rx
Disabled
MACs
Enabled
Disabled
Disabled
Host Interface
Enabled
Disabled
Disabled
Internal PLL Clock
DS00002642A-page 50
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
3.10.1
NORMAL OPERATION MODE
Normal operation mode is the power management mode entered into after device power-up or after hardware reset pin
63. It is established via bits[1:0] = “00” in the PMCTRL register. When the KSZ8463 is in normal operation mode, all PLL
clocks are running, PHYs and MACs are on, and the CPU is ready to read or write the KSZ8463 through these serial
interfaces (SPI and MIIM).
During the normal operation mode, the host CPU can change the power management mode bits[1:0] in the PMCTRL
register to transition to another desired power management mode
3.10.2
ENERGY-DETECT MODE
Energy-detect mode provides a mechanism to save more power than in normal operation mode when the KSZ8463 is
not connected to an active link partner. For example, if the cable is not present or it is connected to a powered down
partner, the KSZ8463 can automatically enter the low power state in energy detect mode. Once activity resumes after
attaching a cable or by a link partner attempting to establish a link, the KSZ8463 will automatically power-up into the
normal power state in energy detect normal power state. The energy-detect mode function is not valid in fiber mode
using the KSZ8463FML and KSZ8463FRL devices.
Energy-detect mode consists of two states, normal-power state and low-power state. While in low-power state, the
KSZ8463 reduces power consumption by disabling all circuitry except the energy detect circuitry of the receiver. Energy
detect mode is enabled by setting bits[1:0] = “01” in the PMCTRL register. When the KSZ8463 is in this mode, it will
monitor the cable energy. If there is no energy on the cable for a time longer than a pre-configured value determined by
bits[7:0] (Go-Sleep Time) in the GST register, the device will go into the low-power state. When the KSZ8463 is in lowpower state, it will keep monitoring the cable energy. Once energy is detected from the cable and is present for a time
longer than 100 ns, the KSZ8463 will enter the normal-power state.
3.10.3
GLOBAL SOFT POWER-DOWN MODE
Soft power-down mode is entered by setting bits[1:0] = “10” in PMCTRL register. When the device is in this mode, all
PLL clocks are disabled, the PHYs and the MACs are off, all internal registers value will change to default value, and
the CPU serial interface is only used to wake-up this device from the current soft power-down mode to normal operation
mode by setting bits[1:0] = “00” in the PMCTRL register.
All strapping pins are sampled to latch any new values when soft power-down is disabled.
3.10.4
ENERGY EFFICIENT ETHERNET (EEE)
Energy Efficient Ethernet (EEE) is implemented in the KSZ8463ML device as described in the IEEE 802.3AZ specification for MII operations on Port 1 and Port 2. The EEE function is not available for fiber mode Ports using the
KSZ8463FML and KSZ8463FRL devices. EEE is not performed at Port 3 since that is a MAC to MAC interface and not
a MAC to PHY interface. The internal connection between the MAC and PHY blocks are performed in MII mode. The
details of the implementation are provided in the information that follows. The standards are defined around a MAC that
supports special signaling associated with EEE. EEE saves power by keeping the voltage on the Ethernet cable at
approximately 0V for as often as possible during periods of no traffic activity. This is called low-power idle (LPI) state.
However, the link will respond automatically when traffic resumes and do so in such a way as to not cause blocking or
dropping of any packets (the wake-up time for 100BASE-TX is specified to be less than 30 µs.). The transmit and
receive directions are independently controlled. Note the EEE is not specified or implemented for 10BASE-T. In
10BASE-T, the transmitter is already OFF during idle periods.
The EEE feature is enabled by default. EEE is auto-negotiated independently for each direction on a link, and is enabled
only if both nodes on a link support it. To disable EEE, clear the Next Page Enable bit(s) for the desired port(s) in the
PCSEEEC register (0x0F3) and restart auto-negotiation.
Based on the EEE specification, the energy savings from EEE occurs at the PHY level. However, the KSZ8463 device
reduces the power consumption not only in the PHY block but also in the MAC and switch blocks by shutting down any
unused clocks as much as possible when the device is at LPI state. A comprehensive LPI request on/off policy is also
built-in at the switch level to determine when to issue LPI requests and when to stop the LPI request. Some software
control options are provided in the device to terminate the LPI request in the early phase when certain events occur to
reduce the latency impact during LPI recovery. A configurable LPI recovery time register is provided at each port to specify the recovery time (25 µs at default) required for the KSZ8463 and its link partner before they are ready to transmit
and receive a packet after going back to the normal state. For details, please refer to the KSZ8463 EEE registers (0x0E0
– 0x0F7) description.
The time during which LPI mode is active is during what is called quiet time. This is shown in Figure 3-17.
2018 Microchip Technology Inc.
DS00002642A-page 51
KSZ8463ML/RL/FML/FRL
FIGURE 3-17:
TRAFFIC ACTIVITY AND EEE
IDLE
Tr
QUIET
WAKE
Tq
QUIET
REFRESH
Ts
QUIET
REFRESH
SLEEP
DATA IDLE
ACTIVE
LOW POWER
ACTIVE
DATA IDLE
Tw_PHY
Tw_SYSTEM
3.10.5
TRANSMIT DIRECTION CONTROL FOR MII MODE
For ports 1 and 2, low-power idle (LPI) state for the transmit direction will be entered when the internal EEE MAC signals
to its PHY to do so. The PHY will stay in the transmit LPI state as long as indicated by the MAC. The TX_CLK is not
stopped.
Even though the PHY is in LPI state, it will periodically leave the LPI state to transmit a refresh signal using specific
transmit code bits. This allows the link partner to keep track of the long-term variation of channel characteristics and
clock drift between the two partners. Approximately every 20 ms – 22 ms, the PHY will transmit a bit pattern to its link
partner of duration 200 µs – 220 µs. The refresh times are listed in Figure 3-17.
3.10.6
RECEIVE DIRECTION CONTROL FOR MII MODE
If enabled for LPI mode, upon receiving a P Code bit pattern (refresh), the PHY will enter the LPI state and signal to the
internal MAC. If the PHY receives some non-P Code bit pattern, it will signal to the MAC to return to “normal frame”
mode. The PHY can turn off the RX_CLK after nine or more clocks have occurred in the LPI state.
In the EEE-compliant environment, the internal PHYs will be monitoring and expecting the P Code (refresh) bit pattern
from its link partner that is generated approximately every 20 ms – 22 ms, with a duration of about 200 µs – 220 µs. This
allows the link partner to keep track of the long term variation of channel characteristics and clock drift between the two
partners.
3.10.7
REGISTERS ASSOCIATED WITH EEE
The following registers are used to configure or manage the EEE feature:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Reg. DCh, DDh – P1ANPT – Port 1 Auto-Negotiation Next Page Transmit Register
Reg. DEh, DFh – P1ALPRNP – Port 1 Auto-Negotiation Link Partner Received Next Page Register
Reg. E0h, E1h – P1EEEA – Port 1 EEE and Link Partner Advertisement Register
Reg. E2h, E3h – P1EEEWEC – Port 1 EEE Wake Error Count Register
Reg. E4h, E5h – P1EEECS – Port 1 EEE Control/Status and Auto-Negotiation Expansion Register
Reg. E6h – P1LPIRTC – Port 1 LPI Recovery Time Counter Register
Reg. E7h – BL2LPIC1 – Buffer Load to LPI Control 1 Register
Reg. E8h, E9h – P2ANPT – Port 2 Auto-Negotiation Next Page Transmit Register
Reg. EAh, EBh – P2ALPRNP – Port 2 Auto-Negotiation Link Partner Received Next Page Register
Reg. ECh, EDh – P2EEEA – Port 2 EEE and Link Partner Advertisement Register
Reg. EEh, EFh – P2EEEWEC – Port 2 EEE Wake Error Count Register
Reg. F0h, F1h – P2EEECS – Port 2 EEE Control/Status and Auto-Negotiation Expansion Register
Reg. F2h – P2LPIRTC – Port 2 LPI Recovery Time Counter Register
Reg. F3h – PCSEEEC – PCS EEE Control Register
Reg. F4h, F5h – ETLWTC – Empty TXQ to LPI Wait Time Control Register
Reg. F6h, F7h – BL2LPIC2 – Buffer Load to LPI Control 2 Register
DS00002642A-page 52
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
3.11
Interrupt Generation on Power Management-Related Events
The various status bits associated with link change and energy detect situations are found in the PMCTRL Register
(0x032 – 0x033) bits[3:2]. The enabling of these signals to generate an interrupt are in IER (0x190 – 0x191) bits[3:2].
The actual interrupt status for these bits are located in ISR (0x192 – 0x193) bits[3:2].
3.12
Interfaces
The KSZ8463 device incorporates a number of interfaces to enable it to be designed into a standard network environment as well as a vendor unique environment. The available interfaces are summarized in Table 3-12. The details of
each usage in the table are provided in the sections which follow.
TABLE 3-12:
AVAILABLE INTERFACES
Registers
Accessed
Interface
Type
Usage
SPI
Configuration
and Register
Access
[As Slave Serial Bus] – External CPU or controller can R/W all
internal registers through this interface.
MIIM
Configuration
and Register
Access
MDC/MDIO-capable CPU or controllers can R/W PHY registers.
All
PHY Only
MII
Data Flow
Interface to the port 3 MAC using the standard MII timing.
N/A
RMII
Data Flow
Interface to the port 3 MAC using the faster reduced RMII timing.
N/A
PHY
Data Flow
Interface to the two internal PHY devices.
N/A
3.12.1
CONFIGURATION INTERFACE
The KSZ8463 supports a serial configuration interface, which may be either SPI or MIIM. The strapping option on pin
35 (RXD0) and pin 34 (RXD1) is used to select one of these two interfaces. This setting may be read in the serial bus
selection bits in the configuration status and serial bus mode register (0x0D8 – 0x0D9): CFGR.
3.12.2
SPI SLAVE SERIAL BUS CONFIGURATION
The KSZ8463 supports a SPI interface in slave mode (see Strapping Options). In this managed mode, an external SPI
master device (micro-controller or CPU) supplies the serial clock (SPI_SCLK), chip select (SPI_CSN), and serial input
data (SPI_DI). Serial output data (SPI_DO) is driven out by the KSZ8463. SPI operations start with the falling edge of
SPI_CSN and end with the rising edge of SPI_CSN. SPI_SCLK is expected to stay low when SPI operation is idle. A
SPI master device (external controller/CPU) has complete programming access to all KSZ8463 registers. Table 3-13
shows the SPI interface connection for the KSZ8463.
TABLE 3-13:
SPI CONNECTION
Pin Number
SPI Slave Signal Name
External Processor (SPI Master)
Signal Description
42
SPI_CSN (input)
SPI Chip Select (Master output)
44
SPI_SCLK (input)
SPI Clock (Master output)
45
SPI_DI (input)
SPI Data Out (Master output)
41
SPI_DO (output)
SPI Data In (Master input)
Input data on SPI_DI (MOSI) is sampled by the KSZ8463 on the rising edge of SPI_SCLK. Timing of the output data on
SPI_DO (MISO) is user-selectable by a strapping option on pin 33. The options are high-speed SPI and low-speed SPI:
• High-Speed SPI Mode: SPI_DO is clocked out at the rising edge of SPI_SCLK mode. The master will typically
sample MISO data at the falling edge of SPI_SCLK, but depending on the MISO hold time requirements of the
master, rising edge sampling may be possible.
• Low-Speed SPI Mode: SPI_DO is clocked out at the falling edge of SPI_SCLK, ½ cycle later than high-speed SPI
mode. The master will typically sample MISO data at the rising edge of SPI_SCLK.
The KSZ8463 supports two standard SPI commands:
• Internal I/O registers read (Opcode = “0”)
2018 Microchip Technology Inc.
DS00002642A-page 53
KSZ8463ML/RL/FML/FRL
• Internal I/O registers write (Opcode = “1”)
As shown in Table 3-14 and Figure 3-18, there are two phases in each SPI operation. The first is the command phase,
followed by the data phase. The command phase is two bytes long for register access. The data phase is in the range
of one to four bytes long depending on the specified byte enable bits B[3:0] in command phase.
TABLE 3-14:
REGISTER ACCESS USING THE SPI INTERFACE
Command Phase (SI Pin)
Byte 0 [7:0]
SPI Operation
Data Phase
(SO or SI Pins)
Byte 1 [7:0]
Op
Register Address
Byte Enable
TA Bits
Register Read
0
A10 A9 A8 A7 A6 A5 A4
A3 A2 B3 B2 B1 B0
XX
Register Write
1
A10 A9 A8 A7 A6 A5 A4
A3 A2 B3 B2 B1 B0
XX
Note 3-1
1 to 4 Bytes
(Read Data on SO pin)
1 to 4 Bytes
(Write Data on SI pin)
In Command phase, Address A[10:2] access register location in double-word and Byte enable B[3:0]
to indicate which byte to access during read or write. In Data phase, the byte 0 is first in/out and byte
3 is last in/out during read or write.
Note 3-2
B[3:0] -> 1: enable byte; 0: disable byte. CPU can enable any one of the four bytes, lower or higher
two bytes, or all four bytes during the command phase.
Note 3-3
TA bits are “turn around” bits and “don’t care” bits.
3.12.3
SPI REGISTER ACCESS OPERATION TIMING
As shown in Figure 3-10 and Figure 3-11, illustrating the SPI internal I/O registers read and write operation timing, the
first two command byte 0/1 contain opcode (0: read command, 1: write command), A[10:2] address bits to access register location in double words and B[3:0] Byte enable bits to indicate which data byte is available in data phase (1: byte
enable, 0: byte disable). The following is data phase either 1, 2, or 4 bytes depending on B[3:0] setting.
Figure 3-19 and Figure 3-20 show the details of the SPI bus protocol for read and write operations. Initially the master
sends a two-byte command. This command begins with a 1-bit opcode (0: read command, 1: write command). It is followed by address bits A[10] to A[2], then four byte enable bits B[3:0], then finally two zero bits. The byte enable bits are
set to indicate which bytes will be transferred in the data phase of the SPI operation. For a two-byte operation, which is
the most common, B[3:0] = 0011. For a single byte operation, B[3:0] = 0001, and for a four-byte operation, B[3:0] = 1111.
The sequence for data transfer is least significant byte first. Then within each byte, the most significant bit goes first.
FIGURE 3-18:
SPI REGISTER READ OPERATION – LOW-SPEED MODE
SPI_CSN
SPI_SCLK
SPI_DI
SPI_DO
HIGH IMPEDANCE
READ COMMAND BYTE 0
DS00002642A-page 54
READ COMMAND BYTE 1
READ DATA
(1 TO 4 BYTES BASED ON B[3:0])
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
FIGURE 3-19:
SPI REGISTER READ OPERATION – HIGH-SPEED MODE
SPI_CSN
SPI_SCLK
SPI_DI
HIGH IMPEDANCE
SPI_DO
READ COMMAND BYTE 0
FIGURE 3-20:
READ COMMAND BYTE 1
READ DATA
(1 TO 4 BYTES BASED ON B[3:0])
SPI REGISTER WRITE OPERATION TIMING
SPI_CSN
SPI_SCLK
SPI_DI
HIGH IMPEDANCE
SPI_DO
WRITE COMMAND BYTE 0
3.12.4
WRITE COMMAND BYTE 1
WRITE DATA
(1 TO 4 BYTES BASED ON B[3:0])
MII MANAGEMENT (MIIM) INTERFACE
The KSZ8463 supports the IEEE 802.3 MII management interface, also known as the management data input/output
(MDIO) interface. This interface allows upper-layer devices to monitor and control the states of the KSZ8463 PHY block.
An external device with MDC/MDIO capability can read the PHY status or configure the PHY settings. Details on the
MIIM interface can be found in Clause 22.2.4.5 of the IEEE 802.3u Specification. Timing information can be found in
802.3 section 22.3.4.
The MIIM interface consists of the following:
• A physical connection that uses a data signal (MDIO) and a clock signal (MDC) for communication between an
external controller and the KSZ8463 device.
• A specific protocol that operates across the two signal physical connection that allows an external controller to
communicate with the internal PHY devices.
• Access to a set of eight 16-bit registers, consisting of six standard MIIM registers (0x0 – 0x5) and two custom
MIIM registers (0x1D and 0x1F). Each set of registers is duplicated for each internal PHY device.
The MIIM Interface can operate up to a maximum clock speed of 5 MHz and access is limited to only the registers in
the PHY block. Table 3-15 summarizes the MII management interface frame format.
TABLE 3-15:
MII MANAGEMENT INTERFACE FRAME FORMAT
Preamble
(32-Bit)
Start of
Frame
(2-Bit)
Op Code
(2-Bit)
PHY
Address
(5-Bit)
Register
Address
(5-Bit)
TA
(2-Bit)
Register
Data
(16-Bit)
Idle
Read
All 1s
01
10
A[4:0]
Reg[4:0]
Z0
D[15:0]
Z
Write
All 1s
01
01
A[4:0]
Reg[4:0]
10
D[15:0]
Z
Operation
Mode
2018 Microchip Technology Inc.
DS00002642A-page 55
KSZ8463ML/RL/FML/FRL
3.12.5
MEDIA INDEPENDENT INTERFACE (MII)
The media independent interface (MII) is specified in Clause 22 of the IEEE 802.3u Standard. It provides a common
interface between PHY layer and MAC layer devices. The MII provided by the KSZ8463ML and KSZ8463FML is connected to the device’s third MAC on port 3. This interface is operated in PHY Mode or in MAC Mode. This is determined
by the strapping option on the RX_DV pin (pin 31) at the time of de-assertion of RSTN. The interface contains two distinct groups of signals, one for transmission and the other for reception. Table 3-16 describes the signals used by the
MII interface to connect to an external MAC or an external PHY.
TABLE 3-16:
MII INTERFACE SIGNAL AND PIN ASSOCIATIONS
PHY Mode Signals Connection
KSZ8463ML/FML
In PHY Mode
Signals
External MAC
Controller Signals
TX_EN (pin 22, input)
TX_EN
MII_BP (pin 28, input)
MAC Mode Signals Connection
MII Interface
Signals Description
External PHY
Device Signals
KSZ8463ML/FML
In MAC Mode
Signals
Transmit Enable
TX_EN
RX_DV
(pin 31, output)
TX_ER
Transmit Error
TX_ER
NA (not used)
TXD3 (pin 23, input)
TXD3
Transmit Data Bit 3
TXD3
RXD3 (pin 32, output)
TXD2 (pin 24, input)
TXD2
Transmit Data Bit 2
TXD2
RXD2 (pin 33, output)
TXD1 (pin 25, input)
TXD1
Transmit Data Bit 1
TXD1
RXD1 (pin 34, output)
TXD0 (pin 26, input)
TXD0
Transmit Data Bit 0
TXD0
RXD0 (pin 35, output)
TX_CLK
(pin 27, output)
TX_CLK
Transmit Clock
TX_CLK
RX_CLK
(pin 38, output)
COL (pin 37, output)
COL
Collision Detection
COL
COL (pin 37, output)
CRS (pin 36, output)
CRS
Carrier Sense
CRS
CRS (pin 36, output)
RX_DV
(pin 31, output)
RX_DV
Receive Data Valid
RX_DV
TX_EN (pin 22, input)
NA (not used)
RX_ER
Receive Error
RX_ER
MII_BP (pin 28, input)
RXD3 (pin 32, output)
RXD3
Receive Data Bit 3
RXD3
TXD3 (pin 23, input)
RXD2 (pin 33, output)
RXD2
Receive Data Bit 2
RXD2
TXD2 (pin 24, input)
RXD1 (pin 34, output)
RXD1
Receive Data Bit 1
RXD1
TXD1 (pin 25, input)
RXD0 (pin 35, output)
RXD0
Receive Data Bit 0
RXD0
TXD0 (pin 26, input)
RX_CLK
(pin 38, output)
RX_CLK
Receive Clock
RX_CLK
TX_CLK
(pin 27, output)
The MII interface operates in either PHY mode or MAC mode. The data interface is 4-bits wide and runs at one quarter
the network bit rate; either 2.5 MHz in 10BASE-T or 25 MHz in 100BASE-TX (not encoded). Additional signals on the
transmit side indicate when data is valid or when an error occurs during transmission. Similarly, the receive side has
signals that convey when the data is valid and without physical layer errors. For half duplex operation, the COL signal
indicates if a collision has occurred during transmission.
The KSZ8463ML/FML does not provide the RX_ER signal in PHY mode operation or the TX_ER signal in MAC mode
operation. Normally, RX_ER indicates a receive error coming from the physical layer device and TX_ER indicates a
transmit error from the MAC device. Since the switch filters error frames, these MII error signals are not used by the
KSZ8463ML/FML. So, for PHY mode operation, if the device interfacing with the KSZ8463ML/FML has an RX_ER input
pin, it needs to be tied low. And, for MAC mode operation, if the device interfacing with the KSZ8463ML/FML has a
TX_ER input pin, it also needs to be tied low.
The KSZ8463ML/FML provides a bypass feature in the MII PHY mode. The TX_ER/MII_BP pin (pin 28) is used to
enable the MII bypass mode when this pin is tied to high. The MII (port 3) is shut down if TX_ER/MII_BP is set to high
in the MII PHY mode. In this case, no new ingress frames from either port 1 or port 2 will be sent out through port 3 and
only switching between port 1 and port 2 for all ingress packets will occur, and the frames for port 3 already in packet
memory will be flushed out.
DS00002642A-page 56
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
3.12.6
REDUCED MEDIA INDEPENDENT INTERFACE (RMII)
The reduced media independent interface (RMII) specifies a low pin count MII. It is available only on port 3 of the
KSZ8463RL and KSZ8463FRL devices for communication with the MAC attached to that port. As with MII, RMII provides a common interface between physical layer and MAC layer devices, and has the following key characteristics:
•
•
•
•
Supports network data rates of either 10 Mbps or 100 Mbps.
Uses a single 50 MHz clock reference (provided internally or externally) for both transmit and receive data.
Uses independent 2-bit wide transmit and receive data paths.
Contains two distinct groups of signals: one for transmission and the other for reception.
The user should select one the two RMII clocking methods shown in Table 3-17. While EN_REFCLK_O (pin 23) is high,
the KSZ8463RL/FRL will output a 50 MHz clock on REFCLK_O (pin 32), which is derived from the 25 MHz crystal or
oscillator attached to the X1 and X2 inputs. In this mode, REFCLK_O must be externally connected to REFCLK_I (pin
27). While EN_REFCLK_O (pin 23) is low, the KSZ8463RL/FRL will require an external 50 MHz signal to be input to the
REFCLK_I input from an external source. In this mode, the X1 and X2 pins are not used.
TABLE 3-17:
RMII CLOCK SETTINGS
EN_REFCLK_O
(Pin 23)
25/50 MHz Select
(Pin 41)
at Power-Up/Reset
Time
Output on
REFCLK_0 (Pin 32)
0 (Disable)
0 (50 MHz)
1 (Enable)
1 (25 MHz)
Do not use the remainder of logical inputs
Clock Source
Note
No
External 50 MHz
input to REFCLK_I
X1/X2 are not used.
Leave them
unconnected.
50 MHz
REFCLK_O output
must be externally
connected to
REFCLK_I
50 MHz output on
REFCLK_O pin
X1/X2 is connected to
a 25 MHz crystal or
oscillator
—
N/A
N/A
The RMII interface in KSZ8463RL/FRL is connected to the device’s third MAC. It complies with the RMII specification.
Table 3-18 describes the signals used by the RMII interface. Refer to the RMII specification for full details on the signal
descriptions.
TABLE 3-18:
RMII SIGNAL DESCRIPTIONS
RMII
Signal Name
Direction
(with respect to the
PHY)
Direction
(with respect to the
MAC)
REFCLK
Input
Input or Output
Synchronous 50 MHz
clock reference for
receive, transmit, and
control interface
REFCLK_I (input)
CRS_DV
Output
Input
Carrier Sense/
Receive Data Valid
RX_DV (output)
RXD[1:0]
Output
Input
Receive Data Bit[1:0]
RXD[1:0] (output)
TX_EN
Input
Output
Transmit Enable
TX_EN (input)
TXD[1:0]
Input
Output
Transmit Data Bit[1:0]
TXD[1:0] (input)
RX_ER
Output
Input or not required
Receive Error
(not used)
—
—
—
—
TX_ER (input)
Connects to RX_ER
signal of RMII PHY
device
RMII
Signal Description
KSZ8463RL/FRL
RMII Signal
(Direction)
The KSZ8463RL/FRL filters error frames, and thus does not implement the RX_ER output signal. To detect error frames
from RMII PHY devices, the TX_ER input signal of the KSZ8463RL/FRL is connected to the RX_ER output signal of the
RMII PHY device. Collision detection is implemented in accordance with the RMII Specification.
2018 Microchip Technology Inc.
DS00002642A-page 57
KSZ8463ML/RL/FML/FRL
In RMII mode, tie the MII signals (TXD[3:2], RXD[3:2] and TX_ER) to ground via a resistor if they are not used.
The KSZ8463RL/FRL can interface to either an RMII PHY or an RMII MAC device. The RMII MAC device allows two
KSZ8463RL/FRL devices to be connected back-to-back. Table 3-19 shows the KSZ8463RL/FRL RMII pin connections
with an external RMII PHY and an external RMII MAC, such as another KSZ8463RL/FRL device.
TABLE 3-19:
RMII PHY-TO-MAC AND MAC-TO-MAC SIGNAL CONNECTIONS
KSZ8463RL/FRL PHY-MAC Connections
External
PHY Signals
KSZ8463RL/FRL
MAC Signals
REFCLK
REFCLK_I
TX_EN
TXD1
KSZ8463RL/FRL MAC-MAC Connections
Signal
Descriptions
KSZ8463RL/FRL
MAC Signals
External
MAC Signals
Reference Clock
REFCLK_I
REF_CLK
RX_DV
Carrier Sense/
Receive Data Valid
RX_DV
CRS_DV
RXD1
Receive Data Bit[1]
RXD1
RXD1
TXD0
RXD0
Receive Data Bit[0]
RXD0
RXD0
CRS_DV
TX_EN
Transmit Enable
TX_EN
TX_EN
RXD1
TXD1
Transmit Data Bit[1]
TXD1
TXD1
RXD0
TXD0
Transmit Data Bit[0]
TXD0
TXD0
RX_ER
TX_ER
Receive Error
(not used)
(not used)
DS00002642A-page 58
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.0
REGISTER DESCRIPTIONS
The KSZ8463 device has a rich set of registers available to manage the functionality of the device. Access to these
registers is via the MIIM or SPI interfaces. All of the registers are not accessible via each interface. Figure 4-1 provides
a global picture of accessibility via the various interfaces and addressing ranges from the perspective of each interface.
FIGURE 4-1:
INTERFACE AND REGISTER MAPPING
MIIM
INTERFACE
PHYAD = 0, 1
REGAD = 0 – 5, 1D, 1F
PHY BLOCK
SWITCH CONFIG REGISTERS
00 – 0x0FF
4Ch – 6Bh
00h – 4Bh
6Ch – FFh
ALL OTHER
REGISTERS
100h – 7FFh
100h – 7FFh
SPI
The registers within the linear 0x000 – 0x7FF address space are all accessible via the SPI interface by a microprocessor
or CPU attached to that buss. The mapping of the various functions within that linear address space is summarized in
Table 4-1.
TABLE 4-1:
MAPPING OF FUNCTIONAL AREAS WITHIN THE ADDRESS SPACE
Register Locations
Device Area
Description
0x000 – 0x0FF
Switch Control and Configuration
Registers which control the overall functionality of the Switch, MAC, and PHYs
0x026 – 0x031
Indirect Access Registers
Registers used to indirectly address and
access four distinct areas within the device.
• Management Information Base (MIB)
Counters
• Static MAC Address Table
• Dynamic MAC Address Table
• VLAN Table
0x044 – 0x06B
PHY1 and PHY2 Registers
The same PHY registers as specified in
IEEE 802.3 specification
0x100 – 0x1FF
Interrupts and Global Reset
The registers and bits associated with interrupts and global reset
0x200 – 0x3FF
IEEE 1588 PTP Trigger Control
and Output Registers
2018 Microchip Technology Inc.
Registers used to configure and use the
IEEE 1588 trigger functions
DS00002642A-page 59
KSZ8463ML/RL/FML/FRL
TABLE 4-1:
MAPPING OF FUNCTIONAL AREAS WITHIN THE ADDRESS SPACE (CONTINUED)
Register Locations
4.1
Device Area
Description
0x400 – 0x5FF
IEEE 1588 PTP Time Stamp Input Registers used for controlling and monitorUnits
ing the 1588 timestamp units
0x600 – 0x7FF
IEEE 1588 PTP Clock and Global Registers that control and monitor the PTP
Control
clock, port ingress/egress, and messaging
Register Map of CPU Accessible I/O Registers
In managed switch mode, the registers within the KSZ8463 can be accessed using the SPI slave serial bus interface.
An external microprocessor communicates with the device through these registers. These registers are used for configuring the device, controlling processes, and reading various statuses.
4.1.1
I/O REGISTERS
The following I/O register space mapping tables apply to 8-bit or 16-bit locations. Depending upon the serial bus mode
selected, each I/O access can be performed using the following operations:
• Using 8-bit accesses for all serial bus modes, there are 2048-byte address locations.
• In byte, word, or double word access for SPI serial bus mode only.
TABLE 4-2:
INTERNAL I/O REGISTER SPACE MAPPING FOR SWITCH CONTROL AND
CONFIGURATION (0X000 – 0X0FF)
I/O Register Offset Location
Register Name
Default Value
0x000 – 0x001
0x000
0x001
CIDER
0x8443 (ML,
FML)
0x8453 (RL,
FRL)
0x002 – 0x003
0x002
0x003
SGCR1
0x3450
Switch Global Control Register 1 [15:0]
0x004 – 0x005
0x004
0x005
SGCR2
0x00F0
Switch Global Control Register 2 [15:0]
0x006 – 0x007
0x006
0x007
SGCR3
0x6320
Switch Global Control Register 3 [15:0]
0x008 – 0x00B
0x008
0x00B
Reserved
(4-Bytes)
Don’t Care
0x00C – 0x00D
0x00C
0x00D
SGCR6
0xFA50
Switch Global Control Register 6 [15:0]
0x00E – 0x00F
0x00E
0x00F
SGCR7
0x0827
Switch Global Control Register 7 [15:0]
0x010 – 0x011
0x010
0x011
MACAR1
0x0010
MAC Address Register 1 [15:0]
0x012 – 0x013
0x012
0x013
MACAR2
0xA1FF
MAC Address Register 2 [15:0]
0x014 – 0x015
0x014
0x015
MACAR3
0xFFFF
MAC Address Register 3 [15:0]
0x016 – 0x017
0x016
0x017
TOSR1
0x0000
TOS Priority Control Register 1 [15:0]
0x018 – 0x019
0x018
0x019
TOSR2
0x0000
TOS Priority Control Register 2 [15:0]
0x01A – 0x01B
0x01A
0x01B
TOSR3
0x0000
TOS Priority Control Register 3 [15:0]
0x01C – 0x01D
0x01C
0x01D
TOSR4
0x0000
TOS Priority Control Register 4 [15:0]
16-Bit
8-Bit
DS00002642A-page 60
Description
Chip ID and Enable Register [15:0]
None
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-2:
INTERNAL I/O REGISTER SPACE MAPPING FOR SWITCH CONTROL AND
CONFIGURATION (0X000 – 0X0FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x01E
0x01F
TOSR5
0x0000
TOS Priority Control Register 5 [15:0]
0x020 – 0x021
0x020
0x021
TOSR6
0x0000
TOS Priority Control Register 6 [15:0]
0x022 – 0x023
0x022
0x023
TOSR7
0x0000
TOS Priority Control Register 7 [15:0]
0x024 – 0x025
0x024
0x025
TOSR8
0x0000
TOS Priority Control Register 8 [15:0]
0x026 – 0x027
0x026
0x027
IADR1
0x0000
Indirect Access Data Register 1 [15:0]
0x028 – 0x029
0x028
0x029
IADR2
0x0000
Indirect Access Data Register 2 [15:0]
0x02A – 0x02B
0x02A
0x02B
IADR3
0x0000
Indirect Access Data Register 3 [15:0]
0x02C – 0x02D
0x02C
0x02D
IADR4
0x0000
Indirect Access Data Register 4 [15:0]
0x02E – 0x02F
0x02E
0x02F
IADR5
0x0000
Indirect Access Data Register 5 [15:0]
0x030 – 0x031
0x030
0x031
IACR
0x0000
Indirect Access Control Register [15:0]
0x032 – 0x033
0x032
0x033
PMCTRL
0x0000
Power Management Control and Wake-up
Event Status Register [15:0]
0x034 – 0x035
0x034
0x035
Reserved
(2-Bytes)
0x0000
None
0x036 – 0x037
0x036
0x037
GST
0x008E
Go Sleep Time Register [15:0]
0x038 – 0x039
0x038
0x039
CTPDC
0x0000
Clock Tree Power Down Control Register
[15:0]
0x03A – 0x04B
0x03A
0x04B
Reserved
(18-Bytes)
Don’t Care
0x04C – 0x04D
0x04C
0x04D
P1MBCR
0x3120
PHY 1 and MII Basic Control Register [15:0]
0x04E – 0x04F
0x04E
0x04F
P1MBSR
0x7808
PHY 1 and MII Basic Status Register [15:0]
0x050 – 0x051
0x050
0x051
PHY1ILR
0x1430
PHY 1 PHYID Low Register [15:0]
0x052 – 0x053
0x052
0x053
PHY1IHR
0x0022
PHY 1 PHYID High Register [15:0]
0x054 – 0x055
0x054
0x055
P1ANAR
0x05E1
PHY 1 Auto-Negotiation Advertisement
Register [15:0]
0x056 – 0x057
0x056
0x057
P1ANLPR
0x0001
PHY 1 Auto-Negotiation Link Partner Ability
Register [15:0]
0x058 – 0x059
0x058
0x059
P2MBCR
0x3120
PHY 2 and MII Basic Control Register [15:0]
0x05A – 0x05B
0x05A
0x05B
P2MBSR
0x7808
PHY 2 and MII Basic Status Register [15:0]
16-Bit
8-Bit
0x01E – 0x01F
2018 Microchip Technology Inc.
Description
None
DS00002642A-page 61
KSZ8463ML/RL/FML/FRL
TABLE 4-2:
INTERNAL I/O REGISTER SPACE MAPPING FOR SWITCH CONTROL AND
CONFIGURATION (0X000 – 0X0FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x05C
0x05D
PHY2ILR
0x1430
PHY 2 PHYID Low Register [15:0]
0x05E – 0x05F
0x05E
0x05F
PHY2IHR
0x0022
PHY 2 PHYID High Register [15:0]
0x060 – 0x061
0x060
0x061
P2ANAR
0x05E1
PHY 2 Auto-Negotiation Advertisement
Register [15:0]
0x062 – 0x063
0x062
0x063
P2ANLPR
0x0001
PHY 2 Auto-Negotiation Link Partner Ability
Register [15:0]
0x064 – 0x065
0x064
0x065
Reserved
(2-Bytes)
Don’t Care
0x066 – 0x067
0x066
0x067
P1PHYCTRL
0x0004
0x068 – 0x069
0x068
0x069
Reserved
(2-Bytes)
Don’t Care
0x06A – 0x06B
0x06A
0x06B
P2PHYCTRL
0x0004
PHY2 Special Control and Status Register
[15:0]
0x06C – 0x06D
0x06C
0x06D
P1CR1
0x0000
Port 1 Control Register 1 [15:0]
0x06E – 0x06F
0x06E
0x06F
P1CR2
0x0607
Port 1 Control Register 2 [15:0]
0x070 – 0x071
0x070
0x071
P1VIDCR
0x0001
Port 1 VID Control Register [15:0]
0x072 – 0x073
0x072
0x073
P1CR3
0x0000
Port 1 Control Register 3 [15:0]
0x074 – 0x075
0x074
0x075
P1IRCR0
0x0000
Port 1 Ingress Rate Control Register 0
[15:0]
0x076 – 0x077
0x076
0x077
P1IRCR1
0x0000
Port 1 Ingress Rate Control Register 1
[15:0]
0x078 – 0x079
0x078
0x079
P1ERCR0
0x0000
Port 1 Egress Rate Control Register 0
[15:0]
0x07A – 0x07B
0x07A
0x07B
P1ERCR1
0x0000
Port 1 Egress Rate Control Register 1
[15:0]
0x07C – 0x07D
0x07C
0x07D
P1SCSLMD
0x0400
Port 1 PHY Special Control/Status, LinkMD
Register [15:0]
0x07E – 0x07F
0x07E
0x07F
P1CR4
0x00FF
Port 1 Control Register 4 [15:0]
0x080 – 0x081
0x080
0x081
P1SR
0x8000
Port 1 Status Register [15:0]
0x082 – 0x083
0x082
0x083
Reserved
(2-Bytes)
Don’t Care
0x084 – 0x085
0x084
0x085
P2CR1
0x0000
Port 2 Control Register 1 [15:0]
0x086 – 0x087
0x086
0x087
P2CR2
0x0607
Port 2 Control Register 2 [15:0]
0x088 – 0x089
0x088
0x089
P2VIDCR
0x0001
Port 2 VID Control Register [15:0]
16-Bit
8-Bit
0x05C – 0x05D
DS00002642A-page 62
Description
None
PHY 1 Special Control and Status Register
[15:0]
None
None
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-2:
INTERNAL I/O REGISTER SPACE MAPPING FOR SWITCH CONTROL AND
CONFIGURATION (0X000 – 0X0FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x08A
0x08B
P2CR3
0x0000
Port 2 Control Register 3 [15:0]
0x08C – 0x08D
0x08C
0x08D
P2IRCR0
0x0000
Port 2 Ingress Rate Control Register 0
[15:0]
0x08E – 0x08F
0x08E
0x08F
P2IRCR1
0x0000
Port 2 Ingress Rate Control Register 1
[15:0]
0x090 – 0x091
0x090
0x091
P2ERCR0
0x0000
Port 2 Egress Rate Control Register 0
[15:0]
0x092 – 0x093
0x092
0x093
P2ERCR1
0x0000
Port 2 Egress Rate Control Register 1
[15:0]
0x094 – 0x095
0x094
0x095
P2SCSLMD
0x0400
Port 2 PHY Special Control/Status, LinkMD
Register [15:0]
0x096 – 0x097
0x096
0x097
P2CR4
0x00FF
Port 2 Control Register 4 [15:0]
0x098 – 0x099
0x098
0x099
P2SR
0x8000
Port 2 Status Register [15:0]
0x09A – 0x09B
0x09A
0x09B
Reserved
(2-Bytes)
Don’t Care
0x09C – 0x09D
0x09C
0x09D
P3CR1
0x0000
Port 3 Control Register 1 [15:0]
0x09E – 0x09F
0x09E
0x09F
P3CR2
0x0607
Port 3 Control Register 2 [15:0]
0x0A0 – 0x0A1
0x0A0
0x0A1
P3VIDCR
0x0001
Port 3 VID Control Register [15:0]
0x0A2 – 0x0A3
0x0A2
0x0A3
P3CR3
0x0000
Port 3 Control Register 3 [15:0]
0x0A4 – 0x0A5
0x0A4
0x0A5
P3IRCR0
0x0000
Port 3 Ingress Rate Control Register 0
[15:0]
0x0A6 – 0x0A7
0x0A6
0x0A7
P3IRCR1
0x0000
Port 3 Ingress Rate Control Register 1
[15:0]
0x0A8 – 0x0A9
0x0A8
0x0A9
P3ERCR0
0x0000
Port 3 Egress Rate Control Register 0
[15:0]
0x0AA – 0x0AB
0x0AA
0x0AB
P3ERCR1
0x0000
Port 3 Egress Rate Control Register 1
[15:0]
0x0AC – 0x0AD
0x0AC
0x0AD
SGCR8
0x8000
Switch Global Control Register 8 [15:0]
0x0AE – 0x0AF
0x0AE
0x0AF
SGCR9
0x0000
Switch Global Control Register 9 [15:0]
0x0B0 – 0x0B1
0x0B0
0x0B1
SAFMACA1L
0x0000
Source Address Filtering MAC Address 1
Register Low [15:0]
0x0B2 – 0x0B3
0x0B2
0x0B3
SAFMACA1M
0x0000
Source Address Filtering MAC Address 1
Register Middle [15:0]
0x0B4 – 0x0B5
0x0B4
0x0B5
SAFMACA1H
0x0000
Source Address Filtering MAC Address 1
Register High [15:0]
0x0B6 – 0x0B7
0x0B6
0x0B7
SAFMACA2L
0x0000
Source Address Filtering MAC Address 2
Register Low [15:0]
16-Bit
8-Bit
0x08A – 0x08B
2018 Microchip Technology Inc.
Description
None
DS00002642A-page 63
KSZ8463ML/RL/FML/FRL
TABLE 4-2:
INTERNAL I/O REGISTER SPACE MAPPING FOR SWITCH CONTROL AND
CONFIGURATION (0X000 – 0X0FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x0B8
0x0B9
SAFMACA2M
0x0000
Source Address Filtering MAC Address 2
Register Middle [15:0]
0x0BA – 0x0BB
0x0BA
0x0BB
SAFMACA2H
0x0000
Source Address Filtering MAC Address 2
Register High [15:0]
0x0BC – 0x0C7
0x0BC
0x0C7
Reserved
(12-Bytes)
Don’t Care
0x0C8 – 0x0C9
0x0C8
0x0C9
P1TXQRCR1
0x8488
Port 1 TXQ Rate Control Register 1 [15:0]
0x0CA – 0x0CB
0x0CA
0x0CB
P1TXQRCR2
0x8182
Port 1 TXQ Rate Control Register 2 [15:0]
0x0CC – 0x0CD
0x0CC
0x0CD
P2TXQRCR1
0x8488
Port 2 TXQ Rate Control Register 1 [15:0]
0x0CE – 0x0CF
0x0CE
0x0CF
P2TXQRCR2
0x8182
Port 2 TXQ Rate Control Register 2 [15:0]
0x0D0 – 0x0D1
0x0D0
0x0D1
P3TXQRCR1
0x8488
Port 3 TXQ Rate Control Register 1 [15:0]
0x0D2 – 0x0D3
0x0D2
0x0D3
P3TXQRCR2
0x8182
Port 3 TXQ Rate Control Register 2 [15:0]
0x0D4 – 0x0D5
0x0D4
0x0D5
Reserved
(2-Bytes)
Don’t Care
0x0D6 – 0x0D7
0x0D6
0x0D7
IOMXSEL
0x0FFF
Input and Output Multiplex Selection Register [15:0]
0x0D8 – 0x0D9
0x0D8
0x0D9
CFGR
0x00FE
Configuration Status and Serial Bus Mode
Register [15:0]
0x0DA – 0x0DB
0x0DA
0x0DB
Reserved
(2-Bytes)
Don’t Care
0x0DC – 0x0DD
0x0DC
0x0DD
P1ANPT
0x2001
Port 1 Auto-Negotiation Next Page Transmit
Register [15:0]
0x0DE – 0x0DF
0x0DE
0x0DF
P1ALPRNP
0x0000
Port 1 Auto-Negotiation Link Partner
Received Next Page Register [15:0]
0x0E0 – 0x0E1
0x0E0
0x0E1
P1EEEA
0x0002
Port 1 EEE and Link Partner Advertisement
Register [15:0]
0x0E2 – 0x0E3
0x0E2
0x0E3
P1EEEWEC
0x0000
Port 1 EEE Wake Error Count Register
[15:0]
0x0E4 – 0x0E5
0x0E4
0x0E5
P1EEECS
0x8064
Port 1 EEE Control/Status and Auto-Negotiation Expansion Register [15:0]
0x0E6 – 0x0E7
0x0E6
0x0E7
P1LPIRTC
BL2LPIC1
0x27
0x08
Port 1 LPI Recovery Time Counter Register
[7:0]
Buffer Load to LPI Control 1 Register [7:0]
0x0E8 – 0x0E9
0x0E8
0x0E9
P2ANPT
0x2001
Port 2 Auto-Negotiation Next Page Transmit
Register [15:0]
0x0EA – 0x0EB
0x0EA
0x0EB
P2ALPRNP
0x0000
Port 2 Auto-Negotiation Link Partner
Received Next Page Register [15:0]
0x0EC – 0x0ED
0x0EC
0x0ED
P2EEEA
0x0002
Port 2 EEE and Link Partner Advertisement
Register [15:0]
0x0EE – 0x0EF
0x0EE
0x0EF
P2EEEWEC
0x0000
Port 2 EEE Wake Error Count Register
[15:0]
16-Bit
8-Bit
0x0B8 – 0x0B9
DS00002642A-page 64
Description
None
None
None
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-2:
INTERNAL I/O REGISTER SPACE MAPPING FOR SWITCH CONTROL AND
CONFIGURATION (0X000 – 0X0FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x0F0
0x0F1
P2EEECS
0x8064
Port 2 EEE Control/Status and Auto-Negotiation Expansion Register [15:0]
0x0F2 – 0x0F3
0x0F2
0x0F3
P2LPIRTC
PCSEEEC
0x27
0x03
Port 2 LPI Recovery Time Counter Register
[7:0]
PCS EEE Control Register [7:0]
0x0F4 – 0x0F5
0x0F4
0x0F5
ETLWTC
0x03E8
Empty TXQ to LPI Wait Time Control Register [15:0]
0x0F6 – 0x0F7
0x0F6
0x0F7
BL2LPIC2
0xC040
Buffer Load to LPI Control 2 Register [15:0]
0x0F8 - 0x0FF
0x0F8
0x0FF
Reserved
(8-Bytes)
Don’t Care
16-Bit
8-Bit
0x0F0 – 0x0F1
TABLE 4-3:
Description
None
INTERNAL I/O REGISTER SPACE MAPPING FOR INTERRUPTS AND GLOBAL
RESET (0X100 – 0X1FF)
I/O Register Offset Location
Register Name
Default Value
0x100
0x123
Reserved
(36-Bytes)
Don’t Care
0x124 – 0x125
0x124
0x125
MBIR
0x0000
Memory BIST Info Register [15:0]
0x126 – 0x127
0x126
0x127
GRR
0x0000
Global Reset Register [15:0]
0x128 – 0x18F
0x128
0x18F
Reserved
(104-Bytes)
Don’t Care
0x190 – 0x191
0x190
0x191
IER
0x0000
Interrupt Enable Register [15:0]
0x192 – 0x193
0x192
0x193
ISR
0x0000
Interrupt Status Register [15:0]
0x194 – 0x1FF
0x194
0x1FF
Reserved
(108-Bytes)
Don’t Care
16-Bit
8-Bit
0x100 – 0x123
TABLE 4-4:
Description
None
None
None
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TRIGGER OUTPUT (12 UNITS,
0X200 – 0X3FF)
I/O Register Offset Location
Register Name
Default Value
0x200
0x201
TRIG_ERR
0x0000
Trigger Output Unit Error Register [11:0]
0x202 – 0x203
0x202
0x203
TRIG_ACTIVE
0x0000
Trigger Output Unit Active Register [11:0]
0x204 – 0x205
0x204
0x205
TRIG_DONE
0x0000
Trigger Output Unit Done Register [11:0]
0x206 – 0x207
0x206
0x207
TRIG_EN
0x0000
Trigger Output Unit Enable Register [11:0]
0x208 – 0x209
0x208
0x209
TRIG_SW_RST
0x0000
Trigger Output Unit Software Reset Register [11:0]
16-Bit
8-Bit
0x200 – 0x201
2018 Microchip Technology Inc.
Description
DS00002642A-page 65
KSZ8463ML/RL/FML/FRL
TABLE 4-4:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TRIGGER OUTPUT (12 UNITS,
0X200 – 0X3FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x20A
0x20B
TRIG12_PPS_
WIDTH
0x0000
0x20C – 0x21F
0x20C
0x21F
Reserved
(20-Bytes)
Don’t Care
0x220 – 0x221
0x220
0x221
TRIG1_TGT_NSL
0x0000
Trigger Output Unit 1 Target Time in Nanoseconds Low-Word Register [15:0]
0x222 – 0x223
0x222
0x223
TRIG1_TGT_NSH
0x0000
Trigger Output Unit 1 Target Time in Nanoseconds High-Word Register [29:16]
0x224 – 0x225
0x224
0x225
TRIG1_TGT_SL
0x0000
Trigger Output Unit 1 Target Time in Seconds Low-Word Register [15:0]
0x226 – 0x227
0x226
0x227
TRIG1_TGT_SH
0x0000
Trigger Output Unit 1 Target Time in Seconds High-Word Register [31:16]
0x228 – 0x229
0x228
0x229
TRIG1_CFG_1
0x3C00
Trigger Output Unit 1 Configuration/Control
Register1
0x22A – 0x22B
0x22A
0x22B
TRIG1_CFG_2
0x0000
Trigger Output Unit 1 Configuration/Control
Register2
0x22C – 0x22D
0x22C
0x22D
TRIG1_CFG_3
0x0000
Trigger Output Unit 1 Configuration/Control
Register3
0x22E – 0x22F
0x22E
0x22F
TRIG1_CFG_4
0x0000
Trigger Output Unit 1 Configuration/Control
Register4
0x230 – 0x231
0x230
0x231
TRIG1_CFG_5
0x0000
Trigger Output Unit 1 Configuration/Control
Register5
0x232 – 0x233
0x232
0x233
TRIG1_CFG_6
0x0000
Trigger Output Unit 1 Configuration/Control
Register6
0x234 – 0x235
0x234
0x235
TRIG1_CFG_7
0x0000
Trigger Output Unit 1 Configuration/Control
Register7
0x236 – 0x237
0x236
0x237
TRIG1_CFG_8
0x0000
Trigger Output Unit 1 Configuration/Control
Register8
0x238 – 0x23F
0x238
0x23F
Reserved
(8-Bytes)
Don’t Care
0x240 – 0x241
0x240
0x241
TRIG2_TGT_NSL
0x0000
Trigger Output Unit 2 Target Time in Nanoseconds Low-Word Register [15:0]
0x242 – 0x243
0x242
0x243
TRIG2_TGT_NSH
0x0000
Trigger Output Unit 2 Target Time in Nanoseconds High-Word Register [29:16]
0x244 – 0x245
0x244
0x245
TRIG2_TGT_SL
0x0000
Trigger Output Unit 2 Target Time in Seconds Low-Word Register [15:0]
0x246 – 0x247
0x246
0x247
TRIG2_TGT_SH
0x0000
Trigger Output Unit 2 Target Time in Seconds High-Word Register [31:16]
0x248 – 0x249
0x248
0x249
TRIG2_CFG_1
0x3C00
Trigger Output Unit 2 Configuration/Control
Register1
0x24A – 0x24B
0x24A
0x24B
TRIG2_CFG_2
0x0000
Trigger Output Unit 2 Configuration/Control
Register2
0x24C – 0x24D
0x24C
0x24D
TRIG2_CFG_3
0x0000
Trigger Output Unit 2 Configuration/Control
Register3
0x24E – 0x24F
0x24E
0x24F
TRIG2_CFG_4
0x0000
Trigger Output Unit 2 Configuration/Control
Register4
16-Bit
8-Bit
0x20A – 0x20B
DS00002642A-page 66
Description
Trigger Output Unit 12 PPS Pulse Width
Register
None
None
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-4:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TRIGGER OUTPUT (12 UNITS,
0X200 – 0X3FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x250
0x251
TRIG2_CFG_5
0x0000
Trigger Output Unit 2 Configuration/Control
Register5
0x252 – 0x253
0x252
0x253
TRIG2_CFG_6
0x0000
Trigger Output Unit 2 Configuration/Control
Register6
0x254 – 0x255
0x254
0x255
TRIG2_CFG_7
0x0000
Trigger Output Unit 2 Configuration/Control
Register7
0x256 – 0x257
0x256
0x257
TRIG2_CFG_8
0x0000
Trigger Output Unit 2 Configuration/Control
Register8
0x258 – 0x25F
0x258
0x25F
Reserved
(8-Bytes)
Don’t Care
0x260 – 0x261
0x260
0x261
TRIG3_TGT_NSL
0x0000
Trigger Output Unit 3 Target Time in Nanoseconds Low-Word Register [15:0]
0x262 – 0x263
0x262
0x263
TRIG3_TGT_NSH
0x0000
Trigger Output Unit 3 Target Time in Nanoseconds High-Word Register [29:16]
0x264 – 0x265
0x264
0x265
TRIG3_TGT_SL
0x0000
Trigger Output Unit 3 Target Time in Seconds Low-Word Register [15:0]
0x266 – 0x267
0x266
0x267
TRIG3_TGT_SH
0x0000
Trigger Output Unit 3 Target Time in Seconds High-Word Register [31:16]
0x268 – 0x269
0x268
0x269
TRIG3_CFG_1
0x3C00
Trigger Output Unit 3 Configuration/Control
Register1
0x26A – 0x26B
0x26A
0x26B
TRIG3_CFG_2
0x0000
Trigger Output Unit 3 Configuration/Control
Register2
0x26C – 0x26D
0x26C
0x26D
TRIG3_CFG_3
0x0000
Trigger Output Unit 3 Configuration/Control
Register3
0x26E – 0x26F
0x26E
0x26F
TRIG3_CFG_4
0x0000
Trigger Output Unit 3 Configuration/Control
Register4
0x270 – 0x271
0x270
0x271
TRIG3_CFG_5
0x0000
Trigger Output Unit 3 Configuration/Control
Register5
0x272 – 0x273
0x272
0x273
TRIG3_CFG_6
0x0000
Trigger Output Unit 3 Configuration/Control
Register6
0x274 – 0x275
0x274
0x275
TRIG3_CFG_7
0x0000
Trigger Output Unit 3 Configuration/Control
Register7
0x276 – 0x277
0x276
0x277
TRIG3_CFG_8
0x0000
Trigger Output Unit 3 Configuration/Control
Register8
0x278 – 0x27F
0x278
0x27F
Reserved
(8-Bytes)
Don’t Care
0x280 – 0x281
0x280
0x281
TRIG4_TGT_NSL
0x0000
Trigger Output Unit 4 Target Time in Nanoseconds Low-Word Register [15:0]
0x282 – 0x283
0x282
0x283
TRIG4_TGT_NSH
0x0000
Trigger Output Unit 4 Target Time in Nanoseconds High-Word Register [29:16]
0x284 – 0x285
0x284
0x285
TRIG4_TGT_SL
0x0000
Trigger Output Unit 4 Target Time in Seconds Low-Word Register [15:0]
0x286 – 0x287
0x286
0x287
TRIG4_TGT_SH
0x0000
Trigger Output Unit 4 Target Time in Seconds High-Word Register [31:16]
0x288 – 0x289
0x288
0x289
TRIG4_CFG_1
0x3C00
Trigger Output Unit 4 Configuration/Control
Register1
16-Bit
8-Bit
0x250 – 0x251
2018 Microchip Technology Inc.
Description
None
None
DS00002642A-page 67
KSZ8463ML/RL/FML/FRL
TABLE 4-4:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TRIGGER OUTPUT (12 UNITS,
0X200 – 0X3FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x28A
0x28B
TRIG4_CFG_2
0x0000
Trigger Output Unit 4 Configuration/Control
Register2
0x28C – 0x28D
0x28C
0x28D
TRIG4_CFG_3
0x0000
Trigger Output Unit 4 Configuration/Control
Register3
0x28E – 0x28F
0x28E
0x28F
TRIG4_CFG_4
0x0000
Trigger Output Unit 4 Configuration/Control
Register4
0x290 – 0x291
0x290
0x291
TRIG4_CFG_5
0x0000
Trigger Output Unit 4 Configuration/Control
Register5
0x292 – 0x293
0x292
0x293
TRIG4_CFG_6
0x0000
Trigger Output Unit 4 Configuration/Control
Register6
0x294 – 0x295
0x294
0x295
TRIG4_CFG_7
0x0000
Trigger Output Unit 4 Configuration/Control
Register7
0x296 – 0x297
0x296
0x297
TRIG4_CFG_8
0x0000
Trigger Output Unit 4 Configuration/Control
Register8
0x298 – 0x29F
0x298
0x29F
Reserved
(8-Bytes)
Don’t Care
0x2A0 – 0x2A1
0x2A0
0x2A1
TRIG5_TGT_NSL
0x0000
Trigger Output Unit 5 Target Time in Nanoseconds Low-Word Register [15:0]
0x2A2 – 0x2A3
0x2A2
0x2A3
TRIG5_TGT_NSH
0x0000
Trigger Output Unit 5 Target Time in Nanoseconds High-Word Register [29:16]
0x2A4 – 0x2A5
0x2A4
0x2A5
TRIG5_TGT_SL
0x0000
Trigger Output Unit 5 Target Time in Seconds Low-Word Register [15:0]
0x2A6 – 0x2A7
0x2A6
0x2A7
TRIG5_TGT_SH
0x0000
Trigger Output Unit 5 Target Time in Seconds High-Word Register [31:16]
0x2A8 – 0x2A9
0x2A8
0x2A9
TRIG5_CFG_1
0x3C00
Trigger Output Unit 5 Configuration/Control
Register1
0x2AA – 0x2AB
0x2AA
0x2AB
TRIG5_CFG_2
0x0000
Trigger Output Unit 5 Configuration/Control
Register2
0x2AC – 0x2AD
0x2AC
0x2AD
TRIG5_CFG_3
0x0000
Trigger Output Unit 5 Configuration/Control
Register3
0x2AE – 0x2AF
0x2AE
0x2AF
TRIG5_CFG_4
0x0000
Trigger Output Unit 5 Configuration/Control
Register4
0x2B0 – 0x2B1
0x2B0
0x2B1
TRIG5_CFG_5
0x0000
Trigger Output Unit 5 Configuration/Control
Register5
0x2B2 – 0x2B3
0x2B2
0x2B3
TRIG5_CFG_6
0x0000
Trigger Output Unit 5 Configuration/Control
Register6
0x2B4 – 0x2B5
0x2B4
0x2B5
TRIG5_CFG_7
0x0000
Trigger Output Unit 5 Configuration/Control
Register7
0x2B6 – 0x2B7
0x2B6
0x2B7
TRIG5_CFG_8
0x0000
Trigger Output Unit 5 Configuration/Control
Register8
0x2B8 – 0x2BF
0x2B8
0x2BF
Reserved
(8-Bytes)
Don’t Care
0x2C0 – 0x2C1
0x2C0
0x2C1
TRIG6_TGT_NSL
0x0000
Trigger Output Unit 6 Target Time in Nanoseconds Low-Word Register [15:0]
0x2C2 – 0x2C3
0x2C2
0x2C3
TRIG6_TGT_NSH
0x0000
Trigger Output Unit 6 Target Time in Nanoseconds High-Word Register [29:16]
16-Bit
8-Bit
0x28A – 0x28B
DS00002642A-page 68
Description
None
None
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-4:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TRIGGER OUTPUT (12 UNITS,
0X200 – 0X3FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x2C4
0x2C5
TRIG6_TGT_SL
0x0000
Trigger Output Unit 6 Target Time in Seconds Low-Word Register [15:0]
0x2C6 – 0x2C7
0x2C6
0x2C7
TRIG6_TGT_SH
0x0000
Trigger Output Unit 6 Target Time in Seconds High-Word Register [31:16]
0x2C8 – 0x2C9
0x2C8
0x2C9
TRIG6_CFG_1
0x3C00
Trigger Output Unit 6 Configuration/Control
Register1
0x2CA – 0x2CB
0x2CA
0x2CB
TRIG6_CFG_2
0x0000
Trigger Output Unit 6 Configuration/Control
Register2
0x2CC – 0x2CD
0x2CC
0x2CD
TRIG6_CFG_3
0x0000
Trigger Output Unit 6 Configuration/Control
Register3
0x2CE – 0x2CF
0x2CE
0x2CF
TRIG6_CFG_4
0x0000
Trigger Output Unit 6 Configuration/Control
Register4
0x2D0 – 0x2D1
0x2D0
0x2D1
TRIG6_CFG_5
0x0000
Trigger Output Unit 6 Configuration/Control
Register5
0x2D2 – 0x2D3
0x2D2
0x2D3
TRIG6_CFG_6
0x0000
Trigger Output Unit 6 Configuration/Control
Register6
0x2D4 – 0x2D5
0x2D4
0x2D5
TRIG6_CFG_7
0x0000
Trigger Output Unit 6 Configuration/Control
Register7
0x2D6 – 0x2D7
0x2D6
0x2D7
TRIG6_CFG_8
0x0000
Trigger Output Unit 6 Configuration/Control
Register8
0x2D8 – 0x2DF
0x2D8
0x2DF
Reserved
(8-Bytes)
Don’t Care
0x2E0 – 0x2E1
0x2E0
0x2E1
TRIG7_TGT_NSL
0x0000
Trigger Output Unit 7 Target Time in Nanoseconds Low-Word Register [15:0]
0x2E2 – 0x2E3
0x2E2
0x2E3
TRIG7_TGT_NSH
0x0000
Trigger Output Unit 7 Target Time in Nanoseconds High-Word Register [29:16]
0x2E4 – 0x2E5
0x2E4
0x2E5
TRIG7_TGT_SL
0x0000
Trigger Output Unit 7 Target Time in Seconds Low-Word Register [15:0]
0x2E6 – 0x2E7
0x2E6
0x2E7
TRIG7_TGT_SH
0x0000
Trigger Output Unit 7 Target Time in Seconds High-Word Register [31:16]
0x2E8 – 0x2E9
0x2E8
0x2E9
TRIG7_CFG_1
0x3C00
Trigger Output Unit 7 Configuration/Control
Register1
0x2EA – 0x2EB
0x2EA
0x2EB
TRIG7_CFG_2
0x0000
Trigger Output Unit 7 Configuration/Control
Register2
0x2EC – 0x2ED
0x2EC
0x2ED
TRIG7_CFG_3
0x0000
Trigger Output Unit 7 Configuration/Control
Register3
0x2EE – 0x2EF
0x2EE
0x2EF
TRIG7_CFG_4
0x0000
Trigger Output Unit 7 Configuration/Control
Register4
0x2F0 – 0x2F1
0x2F0
0x2F1
TRIG7_CFG_5
0x0000
Trigger Output Unit 7 Configuration/Control
Register5
0x2F2 – 0x2F3
0x2F2
0x2F3
TRIG7_CFG_6
0x0000
Trigger Output Unit 7 Configuration/Control
Register6
0x2F4 – 0x2F5
0x2F4
0x2F5
TRIG7_CFG_7
0x0000
Trigger Output Unit 7 Configuration/Control
Register7
0x2F6 – 0x2F7
0x2F6
0x2F7
TRIG7_CFG_8
0x0000
Trigger Output Unit 7 Configuration/Control
Register8
16-Bit
8-Bit
0x2C4 – 0x2C5
2018 Microchip Technology Inc.
Description
None
DS00002642A-page 69
KSZ8463ML/RL/FML/FRL
TABLE 4-4:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TRIGGER OUTPUT (12 UNITS,
0X200 – 0X3FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x2F8
0x2FF
Reserved
(8-Bytes)
Don’t Care
0x300 – 0x301
0x300
0x301
TRIG8_TGT_NSL
0x0000
Trigger Output Unit 8 Target Time in Nanoseconds Low-Word Register [15:0]
0x302 – 0x303
0x302
0x303
TRIG8_TGT_NSH
0x0000
Trigger Output Unit 8 Target Time in Nanoseconds High-Word Register [29:16]
0x304 – 0x305
0x304
0x305
TRIG8_TGT_SL
0x0000
Trigger Output Unit 8 Target Time in Seconds Low-Word Register [15:0]
0x306 – 0x307
0x306
0x307
TRIG8_TGT_SH
0x0000
Trigger Output Unit 8 Target Time in Seconds High-Word Register [31:16]
0x308 – 0x309
0x308
0x309
TRIG8_CFG_1
0x3C00
Trigger Output Unit 8 Configuration/Control
Register1
0x30A – 0x30B
0x30A
0x30B
TRIG8_CFG_2
0x0000
Trigger Output Unit 8 Configuration/Control
Register2
0x30C – 0x30D
0x30C
0x30D
TRIG8_CFG_3
0x0000
Trigger Output Unit 8 Configuration/Control
Register3
0x30E – 0x30F
0x30E
0x30F
TRIG8_CFG_4
0x0000
Trigger Output Unit 8 Configuration/Control
Register4
0x310 – 0x311
0x310
0x311
TRIG8_CFG_5
0x0000
Trigger Output Unit 8 Configuration/Control
Register5
0x312 – 0x313
0x312
0x313
TRIG8_CFG_6
0x0000
Trigger Output Unit 8 Configuration/Control
Register6
0x314 – 0x315
0x314
0x315
TRIG8_CFG_7
0x0000
Trigger Output Unit 8 Configuration/Control
Register7
0x316 – 0x317
0x316
0x317
TRIG8_CFG_8
0x0000
Trigger Output Unit 8 Configuration/Control
Register8
0x318 – 0x31F
0x318
0x31F
Reserved
(8-Bytes)
Don’t Care
0x320 – 0x321
0x320
0x321
TRIG9_TGT_NSL
0x0000
Trigger Output Unit 9 Target Time in Nanoseconds Low-Word Register [15:0]
0x322 – 0x323
0x322
0x323
TRIG9_TGT_NSH
0x0000
Trigger Output Unit 9 Target Time in Nanoseconds High-Word Register [29:16]
0x324 – 0x325
0x324
0x325
TRIG9_TGT_SL
0x0000
Trigger Output Unit 9 Target Time in Seconds Low-Word Register [15:0]
0x326 – 0x327
0x326
0x327
TRIG9_TGT_SH
0x0000
Trigger Output Unit 9 Target Time in Seconds High-Word Register [31:16]
0x328 – 0x329
0x328
0x329
TRIG9_CFG_1
0x3C00
Trigger Output Unit 9 Configuration/Control
Register1
0x32A – 0x32B
0x32A
0x32B
TRIG9_CFG_2
0x0000
Trigger Output Unit 9 Configuration/Control
Register2
0x32C – 0x32D
0x32C
0x32D
TRIG9_CFG_3
0x0000
Trigger Output Unit 9 Configuration/Control
Register3
0x32E – 0x32F
0x32E
0x32F
TRIG9_CFG_4
0x0000
Trigger Output Unit 9 Configuration/Control
Register4
0x330 – 0x331
0x330
0x331
TRIG9_CFG_5
0x0000
Trigger Output Unit 9 Configuration/Control
Register5
16-Bit
8-Bit
0x2F8 – 0x2FF
DS00002642A-page 70
Description
None
None
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-4:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TRIGGER OUTPUT (12 UNITS,
0X200 – 0X3FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x332
0x333
TRIG9_CFG_6
0x0000
Trigger Output Unit 9 Configuration/Control
Register6
0x334 – 0x335
0x334
0x335
TRIG9_CFG_7
0x0000
Trigger Output Unit 9 Configuration/Control
Register7
0x336 – 0x337
0x336
0x337
TRIG9_CFG_8
0x0000
Trigger Output Unit 9 Configuration/Control
Register8
0x338 – 0x33F
0x338
0x33F
Reserved
(8-Bytes)
Don’t Care
0x340 – 0x341
0x340
0x341
TRIG10_TGT_NSL
0x0000
Trigger Output Unit 10 Target Time in Nanoseconds Low-Word Register [15:0]
0x342 – 0x343
0x342
0x343
TRIG10_TGT_NSH
0x0000
Trigger Output Unit 10 Target Time in Nanoseconds High-Word Register [29:16]
0x344 – 0x345
0x344
0x345
TRIG10_TGT_SL
0x0000
Trigger Output Unit 10 Target Time in Seconds Low-Word Register [15:0]
0x346 – 0x347
0x346
0x347
TRIG10_TGT_SH
0x0000
Trigger Output Unit 10 Target Time in Seconds High-Word Register [31:16]
0x348 – 0x349
0x348
0x349
TRIG10_CFG_1
0x3C00
Trigger Output Unit 10 Configuration/Control Register1
0x34A – 0x34B
0x34A
0x34B
TRIG10_CFG_2
0x0000
Trigger Output Unit 10 Configuration/Control Register2
0x34C – 0x34D
0x34C
0x34D
TRIG10_CFG_3
0x0000
Trigger Output Unit 10 Configuration/Control Register3
0x34E – 0x34F
0x34E
0x34F
TRIG10_CFG_4
0x0000
Trigger Output Unit 10 Configuration/Control Register4
0x350 – 0x351
0x350
0x351
TRIG10_CFG_5
0x0000
Trigger Output Unit 10 Configuration/Control Register5
0x352 – 0x353
0x352
0x353
TRIG10_CFG_6
0x0000
Trigger Output Unit 10 Configuration/Control Register6
0x354 – 0x355
0x354
0x355
TRIG10_CFG_7
0x0000
Trigger Output Unit 10 Configuration/Control Register7
0x356 – 0x357
0x356
0x357
TRIG10_CFG_8
0x0000
Trigger Output Unit 10 Configuration/Control Register8
0x358 – 0x35F
0x358
0x35F
Reserved
(8-Bytes)
Don’t Care
0x360 – 0x361
0x360
0x361
TRIG11_TGT_NSL
0x0000
Trigger Output Unit 11 Target Time in Nanoseconds Low-Word Register [15:0]
0x362 – 0x363
0x362
0x363
TRIG11_TGT_NSH
0x0000
Trigger Output Unit 11 Target Time in Nanoseconds High-Word Register [29:16]
0x364 – 0x365
0x364
0x365
TRIG11_TGT_SL
0x0000
Trigger Output Unit 11 Target Time in Seconds Low-Word Register [15:0]
0x366 – 0x367
0x366
0x367
TRIG11_TGT_SH
0x0000
Trigger Output Unit 11 Target Time in Seconds High-Word Register [31:16]
0x368 – 0x369
0x368
0x369
TRIG11_CFG_1
0x3C00
Trigger Output Unit 11 Configuration/Control Register1
0x36A – 0x36B
0x36A
0x36B
TRIG11_CFG_2
0x0000
Trigger Output Unit 11 Configuration/Control Register2
16-Bit
8-Bit
0x332 – 0x333
2018 Microchip Technology Inc.
Description
None
None
DS00002642A-page 71
KSZ8463ML/RL/FML/FRL
TABLE 4-4:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TRIGGER OUTPUT (12 UNITS,
0X200 – 0X3FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x36C
0x36D
TRIG11_CFG_3
0x0000
Trigger Output Unit 11 Configuration/Control Register3
0x36E – 0x36F
0x36E
0x36F
TRIG11_CFG_4
0x0000
Trigger Output Unit 11 Configuration/Control Register4
0x370 – 0x371
0x370
0x371
TRIG11_CFG_5
0x0000
Trigger Output Unit 11 Configuration/Control Register5
0x372 – 0x373
0x372
0x373
TRIG11_CFG_6
0x0000
Trigger Output Unit 11 Configuration/Control Register6
0x374 – 0x375
0x374
0x375
TRIG11_CFG_7
0x0000
Trigger Output Unit 11 Configuration/Control Register7
0x376 – 0x377
0x376
0x377
TRIG11_CFG_8
0x0000
Trigger Output Unit 11 Configuration/Control Register8
0x378 – 0x37F
0x378
0x37F
Reserved
(8-Bytes)
Don’t Care
0x380 – 0x381
0x380
0x381
TRIG12_TGT_NSL
0x0000
Trigger Output Unit 12 Target Time in Nanoseconds Low-Word Register [15:0]
0x382 – 0x383
0x382
0x383
TRIG12_TGT_NSH
0x0000
Trigger Output Unit 12 Target Time in Nanoseconds High-Word Register [29:16]
0x384 – 0x385
0x384
0x385
TRIG12_TGT_SL
0x0000
Trigger Output Unit 12 Target Time in Seconds Low-Word Register [15:0]
0x386 – 0x387
0x386
0x387
TRIG12_TGT_SH
0x0000
Trigger Output Unit 12 Target Time in Seconds High-Word Register [31:16]
0x388 – 0x389
0x388
0x389
TRIG12_CFG_1
0x3C00
Trigger Output Unit 12 Configuration/Control Register1
0x38A – 0x38B
0x38A
0x38B
TRIG12_CFG_2
0x0000
Trigger Output Unit 12 Configuration/Control Register2
0x38C – 0x38D
0x38C
0x38D
TRIG12_CFG_3
0x0000
Trigger Output Unit 12 Configuration/Control Register3
0x38E – 0x38F
0x38E
0x38F
TRIG12_CFG_4
0x0000
Trigger Output Unit 12 Configuration/Control Register4
0x390 – 0x391
0x390
0x391
TRIG12_CFG_5
0x0000
Trigger Output Unit 12 Configuration/Control Register5
0x392 – 0x393
0x392
0x393
TRIG12_CFG_6
0x0000
Trigger Output Unit 12 Configuration/Control Register6
0x394 – 0x395
0x394
0x395
TRIG12_CFG_7
0x0000
Trigger Output Unit 12 Configuration/Control Register7
0x396 – 0x397
0x396
0x397
TRIG12_CFG_8
0x0000
Trigger Output Unit 12 Configuration/Control Register8
0x398 – 0x3FF
0x398
0x3FF
Reserved
(104-Bytes)
Don’t Care
16-Bit
8-Bit
0x36C – 0x36D
DS00002642A-page 72
Description
None
None
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-5:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TIME STAMP INPUTS (12
UNITS, 0X400 – 0X5FF)
I/O Register Offset Location
Register Name
Default Value
0x400
0x401
TS_RDY
0x0000
Input Unit Ready Register [11:0]
0x402 – 0x403
0x402
0x403
TS_EN
0x0000
Time stamp Input Unit Enable Register
[11:0]
0x404 – 0x405
0x404
0x405
TS_SW_RST
0x0000
Time stamp Input Unit Software Reset Register [11:0]
0x406 – 0x41F
0x406
0x41F
Reserved
(26-Bytes)
Don’t Care
0x420 – 0x421
0x420
0x421
TS1_STATUS
0x0000
Time stamp Input Unit 1 Status Register
0x422 – 0x423
0x422
0x423
TS1_CFG
0x0000
Time stamp Input Unit 1 Configuration/Control Register
0x424 – 0x425
0x424
0x425
TS1_SMPL1_NSL
0x0000
Time stamp Unit 1 Input Sample Time (1st)
in Nanoseconds Low-Word Register [15:0]
0x426 – 0x427
0x426
0x427
TS1_SMPL1_NSH
0x0000
Time stamp Unit 1 Input Sample Time (1st)
in Nanoseconds High-Word Register
[29:16]
0x428 – 0x429
0x428
0x429
TS1_SMPL1_SL
0x0000
Time stamp Unit 1 Input Sample Time (1st)
in Seconds Low-Word Register [15:0]
0x42A – 0x42B
0x42A
0x42B
TS1_SMPL1_SH
0x0000
Time stamp Unit 1 Input Sample Time (1st)
in Seconds High-Word Register [31:16]
0x42C – 0x42D
0x42C
0x42D
TS1_SMPL1_SUB_NS
0x0000
Time stamp Unit 1 Input Sample Time (1st)
in Sub-Nanoseconds Register [2:0]
0x42E – 0x433
0x42E
0x433
Reserved
(6-Bytes)
Don’t Care
0x434 – 0x435
0x434
0x435
TS1_SMPL2_NSL
0x0000
Time stamp Unit 1 Input Sample Time (2nd)
in Nanoseconds Low-Word Register [15:0]
0x436 – 0x437
0x436
0x437
TS1_SMPL2_NSH
0x0000
Time stamp Unit 1 Input Sample Time (2nd)
in Nanoseconds High-Word Register
[29:16]
0x438 – 0x439
0x438
0x439
TS1_SMPL2_SL
0x0000
Time stamp Unit 1 Input Sample Time (2nd)
in Seconds Low-Word Register [15:0]
0x43A – 0x43B
0x43A
0x43B
TS1_SMPL2_SH
0x0000
Time stamp Unit 1 Input Sample Time (2nd)
in Seconds High-Word Register [31:16]
0x43C – 0x43D
0x43C
0x43D
TS1_SMPL2_SUB_NS
0x0000
Time stamp Unit 1 Input Sample Time (2nd)
in Sub-Nanoseconds Register [2:0]
0x43E – 0x43F
0x43E
0x43F
Reserved
(2-Bytes)
Don’t Care
0x440 – 0x441
0x440
0x441
TS2_STATUS
0x0000
Time stamp Input Unit 2 Status Register
0x442 – 0x443
0x442
0x443
TS2_CFG
0x0000
Time stamp Input Unit 2 Configuration/Control Register
0x444 – 0x445
0x444
0x445
TS2_SMPL1_NSL
0x0000
Time stamp Unit 2 Input Sample Time (1st)
in Nanoseconds Low-Word Register [15:0]
0x446 – 0x447
0x446
0x447
TS2_SMPL1_NSH
0x0000
Time stamp Unit 2 Input Sample Time (1st)
in Nanoseconds High-Word Register
[29:16]
16-Bit
8-Bit
0x400 – 0x401
2018 Microchip Technology Inc.
Description
None
None
None
DS00002642A-page 73
KSZ8463ML/RL/FML/FRL
TABLE 4-5:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TIME STAMP INPUTS (12
UNITS, 0X400 – 0X5FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x448
0x449
TS2_SMPL1_SL
0x0000
Time stamp Unit 2 Input Sample Time (1st)
in Seconds Low-Word Register [15:0]
0x44A – 0x44B
0x44A
0x44B
TS2_SMPL1_SH
0x0000
Time stamp Unit 2 Input Sample Time (1st)
in Seconds High-Word Register [31:16]
0x44C – 0x44D
0x44C
0x44D
TS2_SMPL1_SUB_NS
0x0000
Time stamp Unit 2 Input Sample Time (1st)
in Sub-Nanoseconds Register [2:0]
0x44E – 0x453
0x44E
0x453
Reserved
(6-Bytes)
Don’t Care
0x454 – 0x455
0x454
0x455
TS2_SMPL2_NSL
0x0000
Time stamp Unit 2 Input Sample Time (2nd)
in Nanoseconds Low-Word Register [15:0]
0x456 – 0x457
0x456
0x457
TS2_SMPL2_NSH
0x0000
Time stamp Unit 2 Input Sample Time (2nd)
in Nanoseconds High-Word Register
[29:16]
0x458 – 0x459
0x458
0x459
TS2_SMP2_SL
0x0000
Time stamp Unit 2 Input Sample Time (2nd)
in Seconds Low-Word Register [15:0]
0x45A – 0x45B
0x45A
0x45B
TS2_SMPL2_SH
0x0000
Time stamp Unit 2 Input Sample Time (2nd)
in Seconds High-Word Register [31:16]
0x45C – 0x45D
0x45C
0x45D
TS2_SMPL2_SUB_NS
0x0000
Time stamp Unit 2 Input Sample Time (2nd)
in Sub-Nanoseconds Register [2:0]
0x45E – 0x45F
0x45E
0x45F
Reserved
(2-Bytes)
Don’t Care
0x460 – 0x461
0x460
0x461
TS3_STATUS
0x0000
Time stamp Input Unit 3 Status Register
0x462 – 0x463
0x462
0x463
TS3_CFG
0x0000
Time stamp Input Unit 3 Configuration/Control Register
0x464 – 0x465
0x464
0x465
TS3_SMPL1_NSL
0x0000
Time stamp Unit 3 Input Sample Time (1st)
in Nanoseconds Low-Word Register [15:0]
0x466 – 0x467
0x466
0x467
TS3_SMPL1_NSH
0x0000
Time stamp Unit 3 Input Sample Time (1st)
in Nanoseconds High-Word Register
[29:16]
0x468 – 0x469
0x468
0x469
TS3_SMPL1_SL
0x0000
Time stamp Unit 3 Input Sample Time (1st)
in Seconds Low-Word Register [15:0]
0x46A – 0x46B
0x46A
0x46B
TS3_SMPL1_SH
0x0000
Time stamp Unit 3 Input Sample Time (1st)
in Seconds High-Word Register [31:16]
0x46C – 0x46D
0x46C
0x46D
TS3_SMPL1_SUB_NS
0x0000
Time stamp Unit 3 Input Sample Time (1st)
in Sub-Nanoseconds Register [2:0]
0x46E – 0x473
0x46E
0x473
Reserved
(6-Bytes)
Don’t Care
0x474 – 0x475
0x474
0x475
TS3_SMPL2_NSL
0x0000
Time stamp Unit 3 Input Sample Time (2nd)
in Nanoseconds Low-Word Register [15:0]
0x476 – 0x477
0x476
0x477
TS3_SMPL2_NSH
0x0000
Time stamp Unit 3 Input Sample Time (2nd)
in Nanoseconds High-Word Register
[29:16]
0x478 – 0x479
0x478
0x479
TS3_SMP2_SL
0x0000
Time stamp Unit 3 Input Sample Time (2nd)
in Seconds Low-Word Register [15:0]
0x47A – 0x47B
0x47A
0x47B
TS3_SMPL2_SH
0x0000
Time stamp Unit 3 Input Sample Time (2nd)
in Seconds High-Word Register [31:16]
16-Bit
8-Bit
0x448 – 0x449
DS00002642A-page 74
Description
None
None
None
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-5:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TIME STAMP INPUTS (12
UNITS, 0X400 – 0X5FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x47C
0x47D
TS3_SMPL2_SUB_NS
0x0000
0x47E – 0x47F
0x47E
0x47F
Reserved
(2-Bytes)
Don’t Care
0x480 – 0x481
0x480
0x481
TS4_STATUS
0x0000
Time stamp Input Unit 4 Status Register
0x482 – 0x483
0x482
0x483
TS4_CFG
0x0000
Time stamp Input Unit 4 Configuration/Control Register
0x484 – 0x485
0x484
0x485
TS4_SMPL1_NSL
0x0000
Time stamp Unit 4 Input Sample Time (1st)
in Nanoseconds Low-Word Register [15:0]
0x486 – 0x487
0x486
0x487
TS4_SMPL1_NSH
0x0000
Time stamp Unit 4 Input Sample Time (1st)
in Nanoseconds High-Word Register
[29:16]
0x488 – 0x489
0x488
0x489
TS4_SMPL1_SL
0x0000
Time stamp Unit 4 Input Sample Time (1st)
in Seconds Low-Word Register [15:0]
0x48A – 0x48B
0x48A
0x48B
TS4_SMPL1_SH
0x0000
Time stamp Unit 4 Input Sample Time (1st)
in Seconds High-Word Register [31:16]
0x48C – 0x48D
0x48C
0x48D
TS4_SMPL1_SUB_NS
0x0000
Time stamp Unit 4 Input Sample Time (1st)
in Sub-Nanoseconds Register [2:0]
0x48E – 0x493
0x48E
0x493
Reserved
(6-Bytes)
Don’t Care
0x494 – 0x495
0x494
0x495
TS4_SMPL2_NSL
0x0000
Time stamp Unit 4 Input Sample Time (2nd)
in Nanoseconds Low-Word Register [15:0]
0x496 – 0x497
0x496
0x497
TS4_SMPL2_NSH
0x0000
Time stamp Unit 4 Input Sample Time (2nd)
in Nanoseconds High-Word Register
[29:16]
0x498 – 0x499
0x498
0x499
TS4_SMP2_SL
0x0000
Time stamp Unit 4 Input Sample Time (2nd)
in Seconds Low-Word Register [15:0]
0x49A – 0x49B
0x49A
0x49B
TS4_SMPL2_SH
0x0000
Time stamp Unit 4 Input Sample Time (2nd)
in Seconds High-Word Register [31:16]
0x49C – 0x49D
0x49C
0x49D
TS4_SMPL2_SUB_NS
0x0000
Time stamp Unit 4 Input Sample Time (2nd)
in Sub-Nanoseconds Register [2:0]
0x49E – 0x49F
0x49E
0x49F
Reserved
(2-Bytes)
Don’t Care
0x4A0 – 0x4A1
0x4A0
0x4A1
TS5_STATUS
0x0000
Time stamp Input Unit 5 Status Register
0x4A0 – 0x4A1
0x4A0
0x4A1
TS5_STATUS
0x0000
Time stamp Input Unit 5 Status Register
0x4A2 – 0x4A3
0x4A2
0x4A3
TS5_CFG
0x0000
Time stamp Input Unit 5 Configuration/Control Register
TS5_SMPL1_
NSL
0x0000
Time stamp Unit 5 Input Sample Time (1st)
in Nanoseconds Low-Word Register [15:0]
0x4A7
TS5_SMPL1_
NSH
0x0000
Time stamp Unit 5 Input Sample Time (1st)
in Nanoseconds High-Word Register
[29:16]
0x4A8
0x4A9
TS5_SMPL1_SL
0x0000
Time stamp Unit 5 Input Sample Time (1st)
in Seconds Low-Word Register [15:0]
16-Bit
8-Bit
0x47C – 0x47D
0x4A4 – 0x4A5
0x4A6 – 0x4A7
0x4A8 – 0x4A9
0x4A4
0x4A5
0x4A6
2018 Microchip Technology Inc.
Description
Time stamp Unit 3 Input Sample Time (2nd)
in Sub-Nanoseconds Register [2:0]
None
None
None
DS00002642A-page 75
KSZ8463ML/RL/FML/FRL
TABLE 4-5:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TIME STAMP INPUTS (12
UNITS, 0X400 – 0X5FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x4AA
0x4AB
TS5_SMPL1_SH
0x0000
Time stamp Unit 5 Input Sample Time (1st)
in Seconds High-Word Register [31:16]
0x4AC – 0x4AD
0x4AC
0x4AD
TS5_SMPL1_SUB_NS
0x0000
Time stamp Unit 5 Input Sample Time (1st)
in Sub-Nanoseconds Register [2:0]
0x4AE – 0x4B3
0x4AE
0x4B3
Reserved
(6-Bytes)
Don’t Care
0x4B4 – 0x4B5
0x4B4
0x4B5
TS5_SMPL2_NSL
0x0000
Time stamp Unit 5 Input Sample Time (2nd)
in Nanoseconds Low-Word Register [15:0]
0x4B6 – 0x4B7
0x4B6
0x4B7
TS5_SMPL2_NSH
0x0000
Time stamp Unit 5 Input Sample Time (2nd)
in Nanoseconds High-Word Register
[29:16]
0x4B8 – 0x4B9
0x4B8
0x4B9
TS5_SMP2_SL
0x0000
Time stamp Unit 5 Input Sample Time (2nd)
in Seconds Low-Word Register [15:0]
0x4BA – 0x4BB
0x4BA
0x4BB
TS5_SMPL2_SH
0x0000
Time stamp Unit 5 Input Sample Time (2nd)
in Seconds High-Word Register [31:16]
0x4BC – 0x4BD
0x4BC
0x4BD
TS5_SMPL2_SUB_NS
0x0000
Time stamp Unit 5 Input Sample Time (2nd)
in Sub-Nanoseconds Register [2:0]
0x4BE – 0x4BF
0x4BE
0x4BF
Reserved
(2-Bytes)
Don’t Care
0x4C0 – 0x4C1
0x4C0
0x4C1
TS6_STATUS
0x0000
Time stamp Input Unit 6 Status Register
0x4C2 – 0x4C3
0x4C2
0x4C3
TS6_CFG
0x0000
Time stamp Input Unit 6 Configuration/Control Register
0x4C4 – 0x4C5
0x4C4
0x4C5
TS6_SMPL1_NSL
0x0000
Time stamp Unit 6 Input Sample Time (1st)
in Nanoseconds Low-Word Register [15:0]
0x4C6 – 0x4C7
0x4C6
0x4C7
TS6_SMPL1_NSH
0x0000
Time stamp Unit 6 Input Sample Time (1st)
in Nanoseconds High-Word Register
[29:16]
0x4C8 – 0x4C9
0x4C8
0x4C9
TS6_SMPL1_SL
0x0000
Time stamp Unit 6 Input Sample Time (1st)
in Seconds Low-Word Register [15:0]
0x4CA – 0x4CB
0x4CA
0x4CB
TS6_SMPL1_SH
0x0000
Time stamp Unit 6 Input Sample Time (1st)
in Seconds High-Word Register [31:16]
0x4CC – 0x4CD
0x4CC
0x4CD
TS6_SMPL1_SUB_NS
0x0000
Time stamp Unit 6 Input Sample Time (1st)
in Sub-Nanoseconds Register [2:0]
0x4CE – 0x4D3
0x4CE
0x4D3
Reserved
(6-Bytes)
Don’t Care
0x4D4 – 0x4D5
0x4D4
0x4D5
TS6_SMPL2_NSL
0x0000
Time stamp Unit 6 Input Sample Time (2nd)
in Nanoseconds Low-Word Register [15:0]
0x4D6 – 0x4D7
0x4D6
0x4D7
TS6_SMPL2_NSH
0x0000
Time stamp Unit 6 Input Sample Time (2nd)
in Nanoseconds High-Word Register
[29:16]
0x4D8 – 0x4D9
0x4D8
0x4D9
TS6_SMP2_SL
0x0000
Time stamp Unit 6 Input Sample Time (2nd)
in Seconds Low-Word Register [15:0]
0x4DA – 0x4DB
0x4DA
0x4DB
TS6_SMPL2_SH
0x0000
Time stamp Unit 6 Input Sample Time (2nd)
in Seconds High-Word Register [31:16]
0x4DC – 0x4DD
0x4DC
0x4DD
TS6_SMPL2_SUB_NS
0x0000
Time stamp Unit 6 Input Sample Time (2nd)
in Sub-Nanoseconds Register [2:0]
16-Bit
8-Bit
0x4AA – 0x4AB
DS00002642A-page 76
Description
None
None
None
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-5:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TIME STAMP INPUTS (12
UNITS, 0X400 – 0X5FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x4DE
0x4DF
Reserved
(2-Bytes)
Don’t Care
0x4E0 – 0x4E1
0x4E0
0x4E1
TS7_STATUS
0x0000
Time stamp Input Unit 7 Status Register
0x4E2 – 0x4E3
0x4E2
0x4E3
TS7_CFG
0x0000
Time stamp Input Unit 7 Configuration/Control Register
0x4E4 – 0x4E5
0x4E4
0x4E5
TS7_SMPL1_NSL
0x0000
Time stamp Unit 7 Input Sample Time (1st)
in Nanoseconds Low-Word Register [15:0]
0x4E6 – 0x4E7
0x4E6
0x4E7
TS7_SMPL1_NSH
0x0000
Time stamp Unit 7 Input Sample Time (1st)
in Nanoseconds High-Word Register
[29:16]
0x4E8 – 0x4E9
0x4E8
0x4E9
TS7_SMPL1_SL
0x0000
Time stamp Unit 7 Input Sample Time (1st)
in Seconds Low-Word Register [15:0]
0x4EA – 0x4EB
0x4EA
0x4EB
TS7_SMPL1_SH
0x0000
Time stamp Unit 7 Input Sample Time (1st)
in Seconds High-Word Register [31:16]
0x4EC – 0x4ED
0x4EC
0x4ED
TS7_SMPL1_SUB_NS
0x0000
Time stamp Unit 7 Input Sample Time (1st)
in Sub-Nanoseconds Register [2:0]
0x4EE – 0x4F3
0x4EE
0x4F3
Reserved
(6-Bytes)
Don’t Care
0x4F4 – 0x4F5
0x4F4
0x4F5
TS7_SMPL2_NSL
0x0000
Time stamp Unit 7 Input Sample Time (2nd)
in Nanoseconds Low-Word Register [15:0]
0x4F6 – 0x4F7
0x4F6
0x4F7
TS7_SMPL2_NSH
0x0000
Time stamp Unit 7 Input Sample Time (2nd)
in Nanoseconds High-Word Register
[29:16]
0x4F8 – 0x4F9
0x4F8
0x4F9
TS7_SMP2_SL
0x0000
Time stamp Unit 7 Input Sample Time (2nd)
in Seconds Low-Word Register [15:0]
0x4FA – 0x4FB
0x4FA
0x4FB
TS7_SMPL2_SH
0x0000
Time stamp Unit 7 Input Sample Time (2nd)
in Seconds High-Word Register [31:16]
0x4FC – 0x4FD
0x4FC
0x4FD
TS7_SMPL2_SUB_NS
0x0000
Time stamp Unit 7 Input Sample Time (2nd)
in Sub-Nanoseconds Register [2:0]
0x4FE – 0x4FF
0x4FE
0x4FF
Reserved
(2-Bytes)
Don’t Care
0x500 – 0x501
0x500
0x501
TS8_STATUS
0x0000
Time stamp Input Unit 8 Status Register
0x502 – 0x503
0x502
0x503
TS8_CFG
0x0000
Time stamp Input Unit 8 Configuration/Control Register
0x504 – 0x505
0x504
0x505
TS8_SMPL1_NSL
0x0000
Time stamp Unit 8 Input Sample Time (1st)
in Nanoseconds Low-Word Register [15:0]
0x506 – 0x507
0x506
0x507
TS8_SMPL1_NSH
0x0000
Time stamp Unit 8 Input Sample Time (1st)
in Nanoseconds High-Word Register
[29:16]
0x508 – 0x509
0x508
0x509
TS8_SMPL1_SL
0x0000
Time stamp Unit 8 Input Sample Time (1st)
in Seconds Low-Word Register [15:0]
0x50A – 0x50B
0x50A
0x50B
TS8_SMPL1_SH
0x0000
Time stamp Unit 8 Input Sample Time (1st)
in Seconds High-Word Register [31:16]
0x50C – 0x50D
0x50C
0x50D
TS8_SMPL1_SUB_NS
0x0000
Time stamp Unit 8 Input Sample Time (1st)
in Sub-Nanoseconds Register [2:0]
16-Bit
8-Bit
0x4DE – 0x4DF
2018 Microchip Technology Inc.
Description
None
None
None
DS00002642A-page 77
KSZ8463ML/RL/FML/FRL
TABLE 4-5:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TIME STAMP INPUTS (12
UNITS, 0X400 – 0X5FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x50E
0x513
Reserved
(6-Bytes)
Don’t Care
0x514 – 0x515
0x514
0x515
TS8_SMPL2_NSL
0x0000
Time stamp Unit 8 Input Sample Time (2nd)
in Nanoseconds Low-Word Register [15:0]
0x516 – 0x517
0x516
0x517
TS8_SMPL2_NSH
0x0000
Time stamp Unit 8 Input Sample Time (2nd)
in Nanoseconds High-Word Register
[29:16]
0x518 – 0x519
0x518
0x519
TS8_SMP2_SL
0x0000
Time stamp Unit 8 Input Sample Time (2nd)
in Seconds Low-Word Register [15:0]
0x51A – 0x51B
0x51A
0x51B
TS8_SMPL2_SH
0x0000
Time stamp Unit 8 Input Sample Time (2nd)
in Seconds High-Word Register [31:16]
0x51C – 0x51D
0x51C
0x51D
TS8_SMPL2_SUB_NS
0x0000
Time stamp Unit 8 Input Sample Time (2nd)
in Sub-Nanoseconds Register [2:0]
0x51E – 0x51F
0x51E
0x51F
Reserved
(2-Bytes)
Don’t Care
0x520 – 0x521
0x520
0x521
TS9_STATUS
0x0000
Time stamp Input Unit 9 Status Register
0x522 – 0x523
0x522
0x523
TS9_CFG
0x0000
Time stamp Input Unit 9 Configuration/Control Register
0x524 – 0x525
0x524
0x525
TS9_SMPL1_NSL
0x0000
Time stamp Unit 9 Input Sample Time (1st)
in Nanoseconds High-Word Register [15:0]
0x526 – 0x527
0x526
0x527
TS9_SMPL1_NSH
0x0000
Time stamp Unit 9 Input Sample Time (1st)
in Nanoseconds High-Word Register
[29:16]
0x528 – 0x529
0x528
0x529
TS9_SMPL1_SL
0x0000
Time stamp Unit 9 Input Sample Time (1st)
in Seconds High-Word Register [15:0]
0x52A – 0x52B
0x52A
0x52B
TS9_SMPL1_SH
0x0000
Time stamp Unit 9 Input Sample Time (1st)
in Seconds High-Word Register [31:16]
0x52C – 0x52D
0x52C
0x52D
TS9_SMPL1_SUB_NS
0x0000
Time stamp Unit 9 Input Sample Time (1st)
in Sub-Nanoseconds Register [2:0]
0x52E – 0x533
0x52E
0x533
Reserved
(6-Bytes)
Don’t Care
0x534 – 0x535
0x534
0x535
TS9_SMPL2_NSL
0x0000
Time stamp Unit 9 Input Sample Time (2nd)
in Nanoseconds Low-Word Register [15:0]
0x536 – 0x537
0x536
0x537
TS9_SMPL2_NSH
0x0000
Time stamp Unit 9 Input Sample Time (2nd)
in Nanoseconds High-Word Register
[29:16]
0x538 – 0x539
0x538
0x539
TS9_SMP2_SL
0x0000
Time stamp Unit 9 Input Sample Time (2nd)
in Seconds Low-Word Register [15:0]
0x53A – 0x53B
0x53A
0x53B
TS9_SMPL2_SH
0x0000
Time stamp Unit 9 Input Sample Time (2nd)
in Seconds High-Word Register [31:16]
0x53C – 0x53D
0x53C
0x53D
TS9_SMPL2_SUB_NS
0x0000
Time stamp Unit 9 Input Sample Time (2nd)
in Sub-Nanoseconds Register [2:0]
0x53E – 0x53F
0x53E
0x53F
Reserved
(2-Bytes)
Don’t Care
0x540 – 0x541
0x540
0x541
TS10_STATUS
0x0000
16-Bit
8-Bit
0x50E – 0x513
DS00002642A-page 78
Description
None
None
None
None
Time stamp Input Unit 10 Status Register
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-5:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TIME STAMP INPUTS (12
UNITS, 0X400 – 0X5FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x542
0x543
TS10_CFG
0x0000
Time stamp Input Unit 10 Configuration/
Control Register
0x544 – 0x545
0x544
0x545
TS10_SMPL1_NSL
0x0000
Time stamp Unit 10 Input Sample Time (1st)
in Nanoseconds Low-Word Register [15:0]
0x546 – 0x547
0x546
0x547
TS10_SMPL1_NSH
0x0000
Time stamp Unit 10 Input Sample Time (1st)
in Nanoseconds High-Word Register
[29:16]
0x548 – 0x549
0x548
0x549
TS10_SMPL1_SL
0x0000
Time stamp Unit 10 Input Sample Time (1st)
in Seconds Low-Word Register [15:0]
0x54A – 0x54B
0x54A
0x54B
TS10_SMPL1_SH
0x0000
Time stamp Unit 10 Input Sample Time (1st)
in Seconds High-Word Register [31:16]
0x54C – 0x54D
0x54C
0x54D
TS10_SMPL1_SUB_NS
0x0000
Time stamp Unit 10 Input Sample Time (1st)
in Sub-Nanoseconds Register [2:0]
0x54E – 0x553
0x54E
0x553
Reserved
(6-Bytes)
Don’t Care
0x554 – 0x555
0x554
0x555
TS10_SMPL2_NSL
0x0000
Time stamp Unit 10 Input Sample Time
(2nd) in Nanoseconds Low-Word Register
[15:0]
0x556 – 0x557
0x556
0x557
TS10_SMPL2_NSH
0x0000
Time stamp Unit 10 Input Sample Time
(2nd) in Nanoseconds High-Word Register
[29:16]
0x558 – 0x559
0x558
0x559
TS10_SMP2_S
L
0x0000
Time stamp Unit 10 Input Sample Time
(2nd) in Seconds Low-Word Register [15:0]
0x55A – 0x55B
0x55A
0x55B
TS10_SMPL2_SH
0x0000
Time stamp Unit 10 Input Sample Time
(2nd) in Seconds High-Word Register
[31:16]
0x55C – 0x55D
0x55C
0x55D
TS10_SMPL2_SUB_NS
0x0000
Time stamp Unit 10 Input Sample Time
(2nd) in Sub-Nanoseconds Register [2:0]
0x55E – 0x55F
0x55E
0x55F
Reserved
(2-Bytes)
Don’t Care
0x560 – 0x561
0x560
0x561
TS11_STATUS
0x0000
Time stamp Input Unit 11 Status Register
0x562 – 0x563
0x562
0x563
TS11_CFG
0x0000
Time stamp Input Unit 11 Configuration/
Control Register
0x564 – 0x565
0x564
0x565
TS11_SMPL1_NSL
0x0000
Time stamp Unit 11 Input Sample Time (1st)
in Nanoseconds Low-Word Register [15:0]
0x566 – 0x567
0x566
0x567
TS11_SMPL1_NSH
0x0000
Time stamp Unit 11 Input Sample Time (1st)
in Nanoseconds High-Word Register
[29:16]
0x568 – 0x569
0x568
0x569
TS11_SMPL1_SL
0x0000
Time stamp Unit 11 Input Sample Time (1st)
in Seconds Low-Word Register [15:0]
0x56A – 0x56B
0x56A
0x56B
TS11_SMPL1_SH
0x0000
Time stamp Unit 11 Input Sample Time (1st)
in Seconds High-Word Register [31:16]
0x56C – 0x56D
0x56C
0x56D
TS11_SMPL1_SUB_NS
0x0000
Time stamp Unit 11 Input Sample Time (1st)
in Sub-Nanoseconds Register [2:0]
0x56E – 0x573
0x56E
0x573
Reserved
(6-Bytes)
Don’t Care
16-Bit
8-Bit
0x542 – 0x543
2018 Microchip Technology Inc.
Description
None
None
None
DS00002642A-page 79
KSZ8463ML/RL/FML/FRL
TABLE 4-5:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TIME STAMP INPUTS (12
UNITS, 0X400 – 0X5FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x574
0x575
TS11_SMPL2_NSL
0x0000
Time stamp Unit 11 Input Sample Time
(2nd) in Nanoseconds Low-Word Register
[15:0]
0x576 – 0x577
0x576
0x577
TS11_SMPL2_NSH
0x0000
Time stamp Unit 11 Input Sample Time
(2nd) in Nanoseconds High-Word Register
[29:16]
0x578 – 0x579
0x578
0x579
TS11_SMP2_S
L
0x0000
Time stamp Unit 11 Input Sample Time
(2nd) in Seconds Low-Word Register [15:0]
0x57A – 0x57B
0x57A
0x57B
TS11_SMPL2_SH
0x0000
Time stamp Unit 11 Input Sample Time
(2nd) in Seconds High-Word Register
[31:16]
0x57C – 0x57D
0x57C
0x57D
TS11_SMPL2_SUB_NS
0x0000
Time stamp Unit 11 Input Sample Time
(2nd) in Sub-Nanoseconds Register [2:0]
0x57E – 0x57F
0x57E
0x57F
Reserved
(2-Bytes)
Don’t Care
0x580 – 0x581
0x580
0x581
TS12_STATUS
0x0000
Time stamp Input Unit 12 Status Register
0x582 – 0x583
0x582
0x583
TS12_CFG
0x0000
Time stamp Input Unit 12 Configuration/
Control Register
0x584 – 0x585
0x584
0x585
TS12_SMPL1_NSL
0x0000
Time stamp Unit 12 Input Sample Time (1st)
in Nanoseconds Low-Word Register [15:0]
0x586 – 0x587
0x586
0x587
TS12_SMPL1_NSH
0x0000
Time stamp Unit 12 Input Sample Time (1st)
in Nanoseconds High-Word Register
[29:16]
0x588 – 0x589
0x588
0x589
TS12_SMPL1_SL
0x0000
Time stamp Unit 12 Input Sample Time (1st)
in Seconds Low-Word Register [15:0]
0x58A – 0x58B
0x58A
0x58B
TS12_SMPL1_SH
0x0000
Time stamp Unit 12 Input Sample Time (1st)
in Seconds High-Word Register [31:16]
0x58C – 0x58D
0x58C
0x58D
TS12_SMPL1_SUB_NS
0x0000
Time stamp Unit 12 Input Sample Time (1st)
in Sub-Nanoseconds Register [2:0]
0x58E – 0x593
0x58E
0x593
Reserved
(6-Bytes)
Don’t Care
0x594 – 0x595
0x594
0x595
TS12_SMPL2_NSL
0x0000
Time stamp Unit 12 Input Sample Time
(2nd) in Nanoseconds Low-Word Register
[15:0]
0x596 – 0x597
0x596
0x597
TS12_SMPL2_NSH
0x0000
Time stamp Unit 12 Input Sample Time
(2nd) in Nanoseconds High-Word Register
[29:16]
0x598 – 0x599
0x598
0x599
TS12_SMP2_S
L
0x0000
Time stamp Unit 12 Input Sample Time
(2nd) in Seconds Low-Word Register [15:0]
0x59A – 0x59B
0x59A
0x59B
TS12_SMPL2_SH
0x0000
Time stamp Unit 12 Input Sample Time
(2nd) in Seconds High-Word Register
[31:16]
0x59C – 0x59D
0x59C
0x59D
TS12_SMPL2_SUB_NS
0x0000
Time stamp Unit 12 Input Sample Time
(2nd) in Sub-Nanoseconds Register [2:0]
0x59E – 0x5A3
0x59E
0x5A3
Reserved
(6-Bytes)
Don’t Care
16-Bit
8-Bit
0x574 – 0x575
DS00002642A-page 80
Description
None
None
None
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-5:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TIME STAMP INPUTS (12
UNITS, 0X400 – 0X5FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x5A4
0x5A5
TS12_SMPL3_NSL
0x0000
Time stamp Unit 12 Input Sample Time
(3rd) in Nanoseconds Low-Word Register
[15:0]
0x5A6 – 0x5A7
0x5A6
0x5A7
TS12_SMPL3_NSH
0x0000
Time stamp Unit 12 Input Sample Time
(3rd) in Nanoseconds High-Word Register
[29:16]
0x5A8 – 0x5A9
0x5A8
0x5A9
TS12_SMPL3_SL
0x0000
Time stamp Unit 12 Input Sample Time
(3rd) in Seconds Low-Word Register [15:0]
0x5AA – 0x5AB
0x5AA
0x5AB
TS12_SMPL3_SH
0x0000
Time stamp Unit 12 Input Sample Time
(3rd) in Seconds High-Word Register
[31:16]
0x5AC – 0x5AD
0x5AC
0x5AD
TS12_SMPL3_SUB_NS
0x0000
Time stamp Unit 12 Input Sample Time
(3rd) in Sub-Nanoseconds Register [2:0]
0x5AE – 0x5B3
0x5AE
0x5B3
Reserved
(6-Bytes)
Don’t Care
0x5B4 – 0x5B5
0x5B4
0x5B5
TS12_SMPL4_NSL
0x0000
Time stamp Unit 12 Input Sample Time
(4th) in Nanoseconds Low-Word Register
[15:0]
0x5B6 – 0x5B7
0x5B6
0x5B7
TS12_SMPL4_NSH
0x0000
Time stamp Unit 12 Input Sample Time
(4th) in Nanoseconds High-Word Register
[29:16]
0x5B8 – 0x5B9
0x5B8
0x5B9
TS12_SMPL4_SL
0x0000
Time stamp Unit 12 Input Sample Time
(4th) in Seconds Low-Word Register [15:0]
0x5BA – 0x5BB
0x5BA
0x5BB
TS12_SMPL4_SH
0x0000
Time stamp Unit 12 Input Sample Time
(4th) in Seconds High-Word Register
[31:16]
0x5BC – 0x5BD
0x5BC
0x5BD
TS12_SMPL4_SUB_NS
0x0000
Time stamp Unit 12 Input Sample Time
(4th) in Sub-Nanoseconds Register [2:0]
0x5BE – 0x5C3
0x5BE
0x5C3
Reserved
(6-Bytes)
Don’t Care
0x5C4 – 0x5C5
0x5C4
0x5C5
TS12_SMPL5_NSL
0x0000
Time stamp Unit 12 Input Sample Time
(5th) in Nanoseconds Low-Word Register
[15:0]
0x5C6 – 0x5C7
0x5C6
0x5C7
TS12_SMPL5_NSH
0x0000
Time stamp Unit 12 Input Sample Time
(5th) in Nanoseconds High-Word Register
[29:16]
0x5C8 – 0x5C9
0x5C8
0x5C9
TS12_SMPL5_SL
0x0000
Time stamp Unit 12 Input Sample Time
(5th) in Seconds Low-Word Register [15:0]
0x5CA – 0x5CB
0x5CA
0x5CB
TS12_SMPL5_SH
0x0000
Time stamp Unit 12 Input Sample Time
(5th) in Seconds High-Word Register
[31:16]
0x5CC – 0x5CD
0x5CC
0x5CD
TS12_SMPL5_SUB_NS
0x0000
Time stamp Unit 12 Input Sample Time
(5th) in Sub-Nanoseconds Register [2:0]
0x5CE – 0x5D3
0x5CE
0x5D3
Reserved
(6-Bytes)
Don’t Care
0x5D4 – 0x5D5
0x5D4
0x5D5
TS12_SMPL6_NSL
0x0000
16-Bit
8-Bit
0x5A4 – 0x5A5
2018 Microchip Technology Inc.
Description
None
None
None
Time stamp Unit 12 Input Sample Time
(6th) in Nanoseconds Low-Word Register
[15:0]
DS00002642A-page 81
KSZ8463ML/RL/FML/FRL
TABLE 4-5:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TIME STAMP INPUTS (12
UNITS, 0X400 – 0X5FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x5D6
0x5D7
TS12_SMPL6_NSH
0x0000
Time stamp Unit 12 Input Sample Time
(6th) in Nanoseconds High-Word Register
[29:16]
0x5D8 – 0x5D9
0x5D8
0x5D9
TS12_SMPL6_SL
0x0000
Time stamp Unit 12 Input Sample Time
(6th) in Seconds Low-Word Register [15:0]
0x5DA – 0x5DB
0x5DA
0x5DB
TS12_SMPL6_SH
0x0000
Time stamp Unit 12 Input Sample Time
(6th) in Seconds High-Word Register
[31:16]
0x5DC – 0x5DD
0x5DC
0x5DD
TS12_SMPL6_SUB_NS
0x0000
Time stamp Unit 12 Input Sample Time
(6th) in Sub-Nanoseconds Register [2:0]
0x5DE – 0x5E3
0x5DE
0x5E3
Reserved
(6-Bytes)
Don’t care
0x5E4 – 0x5E5
0x5E4
0x5E5
TS12_SMPL7_NSL
0x0000
Time stamp Unit 12 Input Sample Time
(7th) in Nanoseconds Low-Word Register
[15:0]
0x5E6 – 0x5E7
0x5E6
0x5E7
TS12_SMPL7_NSH
0x0000
Time stamp Unit 12 Input Sample Time
(7th) in Nanoseconds High-Word Register
[29:16]
0x5E8 – 0x5E9
0x5E8
0x5E9
TS12_SMPL7_SL
0x0000
Time stamp Unit 12 Input Sample Time
(7th) in Seconds Low-Word Register [15:0]
0x5EA – 0x5EB
0x5EA
0x5EB
TS12_SMPL7_SH
0x0000
Time stamp Unit 12 Input Sample Time
(7th) in Seconds High-Word Register
[31:16]
0x5EC – 0x5ED
0x5EC
0x5ED
TS12_SMPL7_SUB_NS
0x0000
Time stamp Unit 12 Input Sample Time
(7th) in Sub-Nanoseconds Register [2:0]
0x5EE – 0x5F3
0x5EE
0x5F3
Reserved
(6-Bytes)
Don’t Care
0x5F4 – 0x5F5
0x5F4
0x5F5
TS12_SMPL8_NSL
0x0000
Time stamp Unit 12 Input Sample Time (
8th) in Nanoseconds Low-Word Register
[15:0]
0x5F6 – 0x5F7
0x5F6
0x5F7
TS12_SMPL8_NSH
0x0000
Time stamp Unit 12 Input Sample Time
(8th) in Nanoseconds High-Word Register
[29:16]
0x5F8 – 0x5F9
0x5F8
0x5F9
TS12_SMPL8_SL
0x0000
Time stamp Unit 12 Input Sample Time
(8th) in Seconds Low-Word Register [15:0]
0x5FA – 0x5FB
0x5FA
0x5FB
TS12_SMPL8_SH
0x0000
Time stamp Unit 12 Input Sample Time
(8th) in Seconds High-Word Register
[31:16]
0x5FC – 0x5FD
0x5FC
0x5FD
TS12_SMPL8_SUB_NS
0x0000
Time stamp Unit 12 Input Sample Time
(8th) in Sub-Nanoseconds Register [2:0]
0x5FE – 0x5FF
0x5FE
0x5FF
Reserved
(2-Bytes)
Don’t Care
16-Bit
8-Bit
0x5D6 – 0x5D7
DS00002642A-page 82
Description
None
None
None
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-6:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP 1588 CLOCK AND GLOBAL
CONTROL (0X600 – 0X7FF)
I/O Register Offset Location
Register Name
Default Value
0x600
0x601
PTP_CLK_CTL
0x0002
0x602 – 0x603
0x602
0x603
Reserved
(2-Bytes)
Don’t care
0x604 – 0x605
0x604
0x605
PTP_RTC_NSL
0x0000
PTP Real Time Clock in Nanoseconds LowWord Register [15:0]
0x606 – 0x607
0x606
0x607
PTP_RTC_NSH
0x0000
PTP Real Time Clock in Nanoseconds
High-Word Register [31:16]
0x608 – 0x609
0x608
0x609
PTP_RTC_SL
0x0000
PTP Real Time Clock in Seconds LowWord Register [15:0]
0x60A – 0x60B
0x60A
0x60B
PTP_RTC_SH
0x0000
PTP Real Time Clock in Seconds HighWord Register [31:16]
0x60C – 0x60D
0x60C
0x60D
PTP_RTC_PHASE
0x0000
PTP Real Time Clock in Phase Register
[2:0]
0x60E – 0x60F
0x60E
0x60F
Reserved
(2-Bytes)
Don’t Care
0x610 – 0x611
0x610
0x611
PTP_SNS_RAT
E_L
0x0000
PTP Sub-nanosecond Rate Low-Word Register [15:0]
0x612 – 0x613
0x612
0x613
PTP_SNS_RAT
E_H
0x0000
PTP Sub-nanosecond Rate High-Word
[29:16] and Configuration Register
0x614 – 0x615
0x614
0x615
PTP_TEMP_ADJ_DURA_L
0x0000
PTP Temporary Adjustment Mode Duration
Low-Word Register [15:0]
0x616 – 0x617
0x616
0x617
PTP_TEMP_ADJ_DURA_H
0x0000
PTP Temporary Adjustment Mode Duration
High-Word Register [31:16]
0x618 – 0x61F
0x618
0x61F
Reserved
(8-Bytes)
Don’t Care
0x620 – 0x621
0x620
0x621
PTP_MSG_CFG_1
0x0059
PTP Message Configuration 1 Register
[7:0]
0x622 – 0x623
0x622
0x623
PTP_MSG_CFG_2
0x0404
PTP Message Configuration 2 Register
[10:0]
0x624 – 0x625
0x624
0x625
PTP_DOMAIN_VER
0x0200
PTP Domain and Version Register [11:0]
0x626 – 0x63F
0x626
0x63F
Reserved
(26-Bytes)
Don’t Care
0x640 – 0x641
0x640
0x641
PTP_P1_RX_
LATENCY
0x019F
PTP Port 1 Receive Latency Register [15:0]
0x642 – 0x643
0x642
0x643
PTP_P1_TX_
LATENCY
0x002D
PTP Port 1 Transmit Latency Register
[15:0]
0x644 – 0x645
0x644
0x645
PTP_P1_ASYM
_COR
0x0000
PTP Port 1 Asymmetry Correction Register
[15:0]
0x646 – 0x647
0x646
0x647
PTP_P1_LINK_
DLY
0x0000
PTP Port 1 Link Delay Register [15:0]
0x648 – 0x649
0x648
0x649
P1_XDLY_REQ_TSL
0x0000
PTP Port 1 Egress Time stamp Low-Word
for Pdelay_REQ and Delay_REQ Frames
Register [15:0]
16-Bit
8-Bit
0x600 – 0x601
2018 Microchip Technology Inc.
Description
PTP Clock Control Register [6:0]
None
None
None
None
DS00002642A-page 83
KSZ8463ML/RL/FML/FRL
TABLE 4-6:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP 1588 CLOCK AND GLOBAL
CONTROL (0X600 – 0X7FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x64A
0x64B
P1_XDLY_REQ_TSH
0x0000
PTP Port 1 Egress Time stamp High-Word
for Pdelay_REQ and Delay_REQ Frames
Register [31:16]
0x64C – 0x64D
0x64C
0x64D
P1_SYNC_TSL
0x0000
PTP Port 1 Egress Time stamp Low-Word
for SYNC Frame Register [15:0]
0x64E – 0x64F
0x64E
0x64F
P1_SYNC_TSH
0x0000
PTP Port 1 Egress Time stamp High-Word
for SYNC Frame Register [31:16]
0x650 – 0x651
0x650
0x651
P1_PDLY_RESP_TSL
0x0000
PTP Port 1 Egress Time stamp Low-Word
for Pdelay_resp Frame Register [15:0]
0x652 – 0x653
0x652
0x653
P1_PDLY_RESP_TSH
0x0000
PTP Port 1 Egress Time stamp High-Word
for Pdelay_resp Frame Register [31:16]
0x654 – 0x65F
0x654
0x65F
Reserved
(12-Bytes)
Don’t Care
0x660 – 0x661
0x660
0x661
PTP_P2_RX_LATENCY
0x019F
PTP Port 2 Receive Latency Register [15:0]
0x662 – 0x663
0x662
0x663
PTP_P2_TX_
LATENCY
0x002D
PTP Port 2 Transmit Latency Register
[15:0]
0x664 – 0x665
0x664
0x665
PTP_P2_ASYM
_COR
0x0000
PTP Port 2 Asymmetry Correction Register
[15:0]
0x666 – 0x667
0x666
0x667
PTP_P2_LINK_
DLY
0x0000
PTP Port 2 Link Delay Register [15:0]
0x668 – 0x669
0x668
0x669
P2_XDLY_REQ_TSL
0x0000
PTP Port 2 Egress Time stamp Low-Word
for Pdelay_REQ and Delay_REQ Frames
Register [15:0]
0x66A – 0x66B
0x66A
0x66B
P2_XDLY_REQ_TSH
0x0000
PTP Port 2 Egress Time stamp High-Word
for Pdelay_REQ and Delay_REQ Frames
Register [31:16]
0x66C – 0x66D
0x66C
0x66D
P2_SYNC_TSL
0x0000
PTP Port 2 Egress Time stamp Low-Word
for SYNC Frame Register [15:0]
0x66E – 0x66F
0x66E
0x66F
P2_SYNC_TSH
0x0000
PTP Port 2 Egress Time stamp High-Word
for SYNC Frame Register [31:16]
0x670 – 0x671
0x670
0x671
P2_PDLY_RESP_TSL
0x0000
PTP Port 2 Egress Time stamp Low-Word
for Pdelay_resp Frame Register [15:0]
0x672 – 0x673
0x672
0x673
P2_PDLY_RESP_TSH
0x0000
PTP Port 2 Egress Time stamp High-Word
for Pdelay_resp Frame Register [31:16]
0x674 – 0x67F
0x674
0x67F
Reserved
(12-Bytes)
Don’t Care
0x680 – 0x681
0x680
0x681
GPIO_MONITOR
0x0000
PTP GPIO Monitor Register [11:0]
0x682 – 0x683
0x682
0x683
GPIO_OEN
0x0000
PTP GPIO Output Enable Register [11:0]
0x684 – 0x687
0x684
0x687
Reserved
(4-Bytes)
Don’t Care
0x688 – 0x689
0x688
0x689
PTP_TRIG_IS
0x0000
PTP Trigger Unit Interrupt Status Register
0x68A – 0x68B
0x68A
0x68B
PTP_TRIG_IE
0x0000
PTP Trigger Unit Interrupt Enable Register
16-Bit
8-Bit
0x64A – 0x64B
DS00002642A-page 84
Description
None
None
None
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-6:
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP 1588 CLOCK AND GLOBAL
CONTROL (0X600 – 0X7FF) (CONTINUED)
I/O Register Offset Location
Register Name
Default Value
0x68C
0x68D
PTP_TS_IS
0x0000
PTP Time stamp Unit Interrupt Status Register
0x68E – 0x68F
0x68E
0x68F
PTP_TS_IE
0x0000
PTP Time stamp Unit Interrupt Enable Register
0x690 – 0x733
0x690
0x733
Reserved
(164-Bytes)
Don’t Care
0x734 – 0x735
0x734
0x735
DSP_CNTRL_6
0x3020
0x736 – 0x747
0x736
0x747
Reserved
(18-Bytes)
Don’t Care
0x748 – 0x749
0x748
0x749
ANA_CNTRL_1
0x0000
0x74A – 0x74B
0x74A
0x74B
Reserved
(2-Bytes)
Don’t Care
0x74C – 0x74D
0x74C
0x74D
ANA_CNTRL_3
0x0000
0x74E – 0x7FF
0x74E
0x7FF
Reserved
(178-Bytes)
Don’t Care
16-Bit
8-Bit
0x68C – 0x68D
4.2
Description
None
DSP Control 1 Register
None
Analog Control 1 Register
None
Analog Control 3 Register
None
Register Bit Definitions
The section provides details of the bit definitions for the registers summarized in the previous section. Writing to a bit or
register defined as reserved could cause unpredictable results. If it is necessary to write to registers that contain both
writable and reserved bits in the same register, the user should first read back the reserved bits (RO or RW), then “OR”
the desired settable bits with the value read and write back the “ORed” value back to the register.
Bit Type Definition:
•
•
•
•
•
RO = Read only.
WO = Write only.
RW = Read/Write.
SC = Self-Clear.
W1C = Write “1” to Clear (Write a “1” to clear this bit).
4.2.1
INTERNAL I/O REGISTER SPACE MAPPING FOR SWITCH CONTROL AND
CONFIGURATION (0X000 – 0X0FF)
4.2.1.1
Chip ID and Enable Register (0x000 – 0x001): CIDER
This register contains the chip ID and switch-enable control.
TABLE 4-7:
CHIP ID AND ENABLE REGISTER (0X000 – 0X001): CIDER
Bit
Default
R/W
Description
15 – 8
0x84
RO
Family ID
Chip family ID.
7–4
0x4 or 0x5
RO
Chip ID
0x4 is assigned to KSZ8463ML/FML.
0x5 is assigned to KSZ8463RL/FRL.
3–1
001
RO
Revision ID
Chip revision ID.
2018 Microchip Technology Inc.
DS00002642A-page 85
KSZ8463ML/RL/FML/FRL
TABLE 4-7:
CHIP ID AND ENABLE REGISTER (0X000 – 0X001): CIDER (CONTINUED)
Bit
Default
R/W
Description
0
1
RW
Start Switch
1 = Start the chip.
0 = Switch is disabled.
4.2.1.2
Switch Global Control Register 1 (0x002 – 0x003): SGCR1
This register contains global control bits for the switch function.
TABLE 4-8:
Bit
15
14
13
12
SWITCH GLOBAL CONTROL REGISTER 1 (0X002 – 0X003): SGCR1
Default
0
0
1
1
R/W
Description
RW
Pass All Frames
1 = Switch all packets including bad ones. Used solely for debugging purposes. Works in conjunction with sniffer mode only.
0 = Do not pass bad frames.
RW
Receive 2000 Byte Packet Length Enable
1 = Enables the receipt of packets up to and including 2000 bytes in
length.
0 = Discards the received packets if their length is greater than 2000
bytes.
RW
IEEE 802.3x Transmit Direction Flow Control Enable
1 = Enables transmit direction flow control feature.
0 = Disable transmit direction flow control feature. The switch will not
generate any flow control packets.
RW
IEEE 802.3x Receive Direction Flow Control Enable
1 = Enables receive direction flow control feature.
0 = Disable receive direction flow control feature. The switch will not react
to any received flow control packets.
11
0
RW
Frame Length Field Check
1 = Enable checking frame length field in the IEEE packets. If the actual
length does not match, the packet will be dropped (for Length/Type field
< 1500).
0 = Disable checking frame length field in the IEEE packets.
10
1
RW
Aging Enable
1 = Enable aging function in the chip.
0 = Disable aging function in the chip.
9
0
RW
Fast Age Enable
1 = Turn on fast age (800 μs).
8
0
RW
Aggressive Back-Off Enable
1 = Enable more aggressive back-off algorithm in half-duplex mode to
enhance performance. This is not an IEEE standard.
7–6
01
RW
Reserved
RW
Enable Flow Control when Exceeding Ingress Limit
1 = Flow control frame will be sent to link partner when exceeding the
ingress rate limit.
0 = Frame will be dropped when exceeding the ingress rate limit.
5
0
4
1
RW
Receive 2K Byte Packets Enable
1 = Enable packet length up to 2K bytes. While set, SGCR2 bits[2,1] will
have no effect.
0 = Discard packet if packet length is greater than 2000 bytes.
3
0
RW
Pass Flow Control Packet
1 = Switch will not filter 802.3x “flow control” packets.
2–1
00
RW
Reserved
DS00002642A-page 86
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-8:
Bit
0
4.2.1.3
SWITCH GLOBAL CONTROL REGISTER 1 (0X002 – 0X003): SGCR1 (CONTINUED)
Default
0
R/W
Description
RW
Link Change Age
1 = Link change from “link” to “no link” will cause fast aging ( TXP2/TXM2)
0 = Normal operation
0
0
RW
Reserved
4.2.8
—
PORT 1 CONTROL REGISTERS
4.2.8.1
Port 1 Control Register 1 (0x06C – 0x06D): P1CR1
This register contains control bits for the switch Port 1 function.
TABLE 4-47:
PORT 1 CONTROL REGISTER 1 (0X06C – 0X06D): P1CR1
Bit
Default
R/W
15
0
RO
Reserved
RW
Port 1 LED Direct Control
These bits directly control the port 1 LED pins.
0xx = Normal LED function as set up via Reg. 0x00E – 0x00F, Bits[9:8].
100 = Both port 1 LEDs off.
101 = Port 1 LED1 off, LED0 on.
110 = Port 1 LED1 on, LED0 off.
111 = Both port 1 LEDs on.
RW
Source Address Filtering Enable for MAC Address 2
1 = Enable the source address filtering function when the SA matches
MAC Address 2 in SAFMACA2 (0x0B6 – 0x0BB).
0 = Disable source address filtering function.
14 - 12
11
000
0
Description
10
0
RW
Source Address Filtering Enable for MAC Address 1
1 = Enable the source address filtering function when the SA matches
MAC Address 1 in SAFMACA1 (0x0B0 – 0x0B5).
0 = Disable source address filtering function.
9
0
RW
Drop Tagged Packet Enable
1 = Enable dropping of tagged ingress packets.
0 = Disable dropping of tagged ingress packets.
DS00002642A-page 106
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-47:
Bit
PORT 1 CONTROL REGISTER 1 (0X06C – 0X06D): P1CR1 (CONTINUED)
Default
8
0
R/W
RW
Description
TX Two Queues Select Enable
1 = The port 1 output queue is split into two priority queues (q0 and q1).
0 = Single output queue on port 1. There is no priority differentiation even
though packets are classified into high or low priority.
Also see bit 0 in this register. Do not set both bits 0 and 8.
7
0
RW
Broadcast Storm Protection Enable
1 = Enable broadcast storm protection for ingress packets on port 1.
0 = Disable broadcast storm protection.
6
0
RW
Diffserv Priority Classification Enable
1 = Enable DiffServ priority classification for ingress packets on port 1.
0 = Disable DiffServ function.
5
0
RW
802.1p Priority Classification Enable
1 = Enable 802.1p priority classification for ingress packets on port 1.
0 = Disable 802.1p.
RW
Port-Based Priority Classification
00 = Ingress packets on port 1 are classified as priority 0 queue if “DiffServ” or “802.1p” classification is not enabled or fails to classify.
01 = Ingress packets on port 1 are classified as priority 1 queue if “DiffServ” or “802.1p” classification is not enabled or fails to classify.
10 = Ingress packets on port 1 are classified as priority 2 queue if “DiffServ” or “802.1p” classification is not enabled or fails to classify.
11 = Ingress packets on port 1 are classified as priority 3 queue if “Diffserv” or “802.1p” classification is not enabled or fails to classify.
Note: “DiffServ”, “802.1p” and port priority can be enabled at the same
time. The OR’ed result of 802.1p and DSCP overwrites the port priority.
RW
Tag Insertion
1 = When packets are output on port 1, the switch adds 802.1p/q tags to
packets without 802.1p/q tags when received. The switch will not add
tags to packets already tagged. The tag inserted is the ingress port’s
“port VID”.
0 = Disable tag insertion.
RW
Tag Removal
1 = When packets are output on port 1, the switch removes 802.1p/q tags
from packets with 802.1p/q tags when received. The switch will not modify packets received without tags.
0 = Disable tag removal.
4-3
00
2
0
1
0
0
0
RW
TX Multiple Queues Select Enable
1 = The port 1 output queue is split into four priority queues (q0, q1, q2
and q3).
0 = Single output queue on the port 1. There is no priority differentiation
even though packets are classified into high or low priority.
Also see bit 8 in this register. Do not set both bits 0 and 8.
4.2.8.2
Port 1 Control Register 2 (0x06E – 0x06F): P1CR2
This register contains control bits for the switch port 1 function.
TABLE 4-48:
PORT 1 CONTROL REGISTER 2 (0X06E – 0X06F): P1CR2
Bit
Default
R/W
Description
15
0
RW
Reserved
2018 Microchip Technology Inc.
DS00002642A-page 107
KSZ8463ML/RL/FML/FRL
TABLE 4-48:
Bit
14
13
PORT 1 CONTROL REGISTER 2 (0X06E – 0X06F): P1CR2 (CONTINUED)
Default
0
0
R/W
Description
RW
Ingress VLAN Filtering
1 = The switch discards packets whose VID port membership in VLAN
table bits [18:16] does not include the ingress port VID.
0 = No ingress VLAN filtering.
RW
Discard Non PVID Packets
1 = The switch discards packets whose VID does not match the ingress
port default VID.
0 = No packets are discarded.
12
0
RW
Force Flow Control
1 = Always enable flow control on the port, regardless of auto-negotiation
result.
0 = The flow control is enabled based on auto-negotiation result.
11
0
RW
Back Pressure Enable
1 = Enable port’s half-duplex back pressure.
0 = Disable port’s half-duplex back pressure.
10
1
RW
Transmit Enable
1 = Enable packet transmission on the port.
0 = Disable packet transmission on the port.
9
1
RW
Receive Enable
1 = Enable packet reception on the port.
0 = Disable packet reception on the port.
8
0
RW
Learning Disable
1 = Disable switch address learning capability.
0 = Enable switch address learning.
RW
Sniffer Port
1 = Port is designated as a sniffer port and transmits packets that are
monitored.
0 = Port is a normal port.
RW
Receive Sniff
1 = All packets received on the port are marked as “monitored packets”
and forwarded to the designated “sniffer port.”
0 = No receive monitoring.
7
6
0
0
5
0
RW
Transmit Sniff
1 = All packets transmitted on the port are marked as “monitored packets” and forwarded to the designated “sniffer port.”
0 = No transmit monitoring.
4
0
RW
Reserved
RW
User Priority Ceiling
1 = If the packet’s “priority field” is greater than the “user priority field” in
the port VID control register bit[15:13], replace the packet’s “priority field”
with the “user priority field” in the port VID control register bit[15:13].
0 = Do not compare and replace the packet’s “priority field.”
RW
Port VLAN Membership
Define the port’s port VLAN membership. Bit[2] stands for the host port,
bit [1] for port 2, and bit [0] for port 1. The port can only communicate
within the membership. A ‘1’ includes a port in the membership; a ‘0’
excludes a port from the membership.
3
2-0
4.2.8.3
0
111
Port 1 VID Control Register (0x070 – 0x071): P1VIDCR
This register contains control bits for the switch port 1 function. This register has two main uses. It is associated with the
ingress of untagged packets and used for egress tagging as well as being used for address lookup and providing a
default VID for the ingress of untagged or null-VID-tagged packets.
DS00002642A-page 108
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-49:
PORT 1 VID CONTROL REGISTER (0X070 – 0X071): P1VIDCR
Bit
Default
R/W
Description
15 - 13
0x0
RW
Default Tag[15:13]
Port’s default tag, containing “User Priority Field” bits.
12
0
RW
Default Tag[12]
Port’s default tag, containing the CFI bit.
11 - 0
0x001
RW
Default Tag[11:0]
Port’s default tag, containing the VID[11:0].
4.2.8.4
Port 1 Control Register 3 (0x072 – 0x073): P1CR3
This register contains control bits for the switch port 1 function.
TABLE 4-50:
PORT 1 CONTROL REGISTER 3 (0X072 – 0X073): P1CR3
Bit
Default
15 - 5
4
3-2
Description
0x000
RO
Reserved
0
RW
Reserved
RW
Ingress Limit Mode
These bits determine what kinds of frames are limited and counted
against ingress rate limiting as follows:
00 = Limit and count all frames.
01 = Limit and count Broadcast, Multicast, and flooded Unicast frames.
10 = Limit and count Broadcast and Multicast frames only.
11 = Limit and count Broadcast frames only.
RW
Count Inter-Frame Gap
Count IFG Bytes.
1 = Each frame’s minimum inter frame gap. IFG bytes (12 per frame) are
included in Ingress and Egress rate limiting calculations.
0 = IFG bytes are not counted.
RW
Count Preamble
Count preamble Bytes.
1 = Each frame’s preamble bytes (8 per frame) are included in Ingress
and Egress rate limiting calculations.
0 = Preamble bytes are not counted.
00
1
0
0
4.2.8.5
R/W
0
Port 1 Ingress Rate Control Register 0 (0x074 – 0x075): P1IRCR0
This register contains the port 1 ingress rate limiting control for priority 1 and priority 0.
TABLE 4-51:
PORT 1 INGRESS RATE CONTROL REGISTER 0 (0X074 – 0X075): P1IRCR0
Bit
Default
R/W
Description
15
0
RW
Reserved
14 - 8
0x00
RW
Ingress Data Rate Limit for Priority 1 Frames
Ingress priority 1 frames will be limited or discarded as shown in Table 452.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
7
0
RW
Reserved
RW
Ingress Data Rate Limit for Priority 0 Frames
Ingress priority 0 frames will be limited or discarded as shown in Table 452.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
6-0
0x00
2018 Microchip Technology Inc.
DS00002642A-page 109
KSZ8463ML/RL/FML/FRL
TABLE 4-52:
INGRESS OR EGRESS DATA RATE LIMITS
Data Rate Limit for Ingress or
Egress
4.2.8.6
100BASE-TX for Priority [3:0]
Register Bit[14:8] or Bit[6:0]
10BASE-T for Priority [3:0]
Register Bit[14:8] or Bit[6:0]
0x01 to 0x64 for the rate matches
1 Mbps to 100 Mbps respectively
0x01 to 0x0A for the rate matches
1 Mbps to 10 Mbps respectively
0x00 (default) for the rate is no limit
(full 100 Mbps)
0x00 (default) for the rate
is no limit (full 10 Mbps)
64 Kbps
0x65
128 Kbps
0x66
192 Kbps
0x67
256 Kbps
0x68
320 Kbps
0x69
384 Kbps
0x6A
448 Kbps
0x6B
512 Kbps
0x6C
576 Kbps
0x6D
640 Kbps
0x6E
704 Kbps
0x6F
768 Kbps
0x70
832 Kbps
0x71
896 Kbps
0x72
960 Kbps
0x73
Port 1 Ingress Rate Control Register 1 (0x076 – 0x077): P1IRCR1
This register contains the port 1 ingress rate limiting control bits for priority 3 and priority 2.
TABLE 4-53:
PORT 1 INGRESS RATE CONTROL REGISTER 1 (0X076 – 0X077): P1IRCR1
Bit
Default
R/W
Description
15
0
RW
Reserved
14 - 8
0x00
RW
Ingress Data Rate Limit for Priority 3 Frames
Ingress priority 3 frames will be limited or discarded as shown in Table 452.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
7
0
RW
Reserved
RW
Ingress Data Rate Limit for Priority 2 Frames
Ingress priority 2 frames will be limited or discarded as shown in Table 452.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
6-0
0x00
DS00002642A-page 110
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.8.7
Port 1 Egress Rate Control Register 0 (0x078 – 0x079): P1ERCR0
This register contains the port 1 egress rate limiting control bits for priority 1 and priority 0. When this port is configured
for 1 egress queue (which is the default), only the Priority 0 rate limit is applied. When it is configured for 2 queues, only
the Priority 1 and Priority 0 settings are applied.
TABLE 4-54:
PORT 1 EGRESS RATE CONTROL REGISTER 0 (0X078 – 0X079): P1ERCR0
Bit
Default
R/W
Description
15
0
RW
Reserved
14 - 8
0x00
RW
Egress Data Rate Limit for Priority 1 Frames
Egress priority 1 frames will be limited as shown in Table 4-52.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
7
0
RW
Reserved
RW
Egress Data Rate Limit for Priority 0 Frames
Egress priority 0 frames will be limited as shown in Table 4-52.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
6-0
4.2.8.8
0x00
Port 1 Egress Rate Control Register 1 (0x07A – 0x07B): P1ERCR1
This register contains the port 1 egress rate limiting control bits for priority 3 and priority 2. When this port is configured
for 1 egress queue (which is the default), only the Priority 0 rate limit is applied. When it is configured for 2 queues, only
the Priority 1 and Priority 0 settings are applied.
TABLE 4-55:
PORT 1 EGRESS RATE CONTROL REGISTER 1 (0X07A – 0X07B): P1ERCR1
Bit
Default
R/W
Description
15
0
RW
Reserved
14 - 8
0x00
RW
Egress Data Rate Limit for Priority 3 Frames
Egress priority 3 frames will be limited as shown in the Ingress or Egress
Data Rate Limits table.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
7
0
RW
Reserved
RW
Egress Data Rate Limit for Priority 2 Frames
Egress priority 2 frames will be limited as shown in the Ingress or Egress
Data Rate Limits table.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
6-0
4.2.8.9
0x00
Port 1 PHY Special Control/Status, LinkMD (0x07C – 0x07D): P1SCSLMD
This register contains the LinkMD control and status information of PHY 1.
TABLE 4-56:
PORT 1 PHY SPECIAL CONTROL/STATUS, LINKMD (0X07C – 0X07D): P1SCSLMD
Bit
Default
R/W
Description
Bit is Same As
15
0
RO
CDT_10m_Short
1 = Less than 10 meter short.
Bit [12] in MIIM
PHYAD1 = 0x1,
0x1D
RO
Cable Diagnostic Test Results
[00] = Normal condition.
[01] = Open condition has been detected in cable.
[10] = Short condition has been detected in cable.
[11] = Cable diagnostic test has failed.
Bits[14:13] in
MIIM
PHYAD1 = 0x1,
0x1D
14 - 13
00
2018 Microchip Technology Inc.
DS00002642A-page 111
KSZ8463ML/RL/FML/FRL
TABLE 4-56:
Bit
PORT 1 PHY SPECIAL CONTROL/STATUS, LINKMD (0X07C – 0X07D): P1SCSLMD
Default
R/W
Description
Bit is Same As
Cable Diagnostic Test Enable
1 = Cable diagnostic test is enabled. It is self-cleared
after the test is done.
0 = Indicates that the cable diagnostic test has completed and the status information is valid for reading.
Bit[15] in MIIM
PHYAD1 = 0x1,
0x1D
12
0
RW/SC
11
0
RW
10
1
RW
Reserved
Force_Link
1 = Force link pass.
0 = Normal operation.
Bit[3] in
P1PHYCTRL
—
9
0
RW
Remote (Near-End) Loopback
1 = Perform remote loopback at port 1's PHY
(RXP1/RXM1 -> TXP1/TXM1)
0 = Normal operation
8-0
0x000
RO
CDT_Fault_Count
Distance to the fault. It’s approximately 0.4m*CDT_Fault_Count.
4.2.8.10
Bit[1] in
P1PHYCTRL
Bits[8:0] in MIIM
PHYAD1 = 0x1,
0x1D
Port 1 Control Register 4 (0x07E – 0x07F): P1CR4
This register contains control bits for the switch port 1 function.
TABLE 4-57:
PORT 1 CONTROL REGISTER 4 (0X07E – 0X07F): P1CR4
Bit
Default
R/W
Description
15
0
RW
Reserved
14
0
RW
Disable Transmit
1 = Disable the port’s transmitter.
0 = Normal operation.
Bit[1] in
P1MBCR
13
0
RW/SC
Restart Auto-Negotiation
1 = Restart auto-negotiation.
0 = Normal operation.
Bit[9] in
P1MBCR
RW
Disable Far-End-Fault
1 = Disable far-end-fault detection.
0 = Normal operation.
For 100BASE-FX fiber mode operation.
Bit[2] in
P1MBCR
Bit[11] in
P1MBCR
12
0
Bit is Same As
—
11
0
RW
Power Down
1 = Power down.
0 = Normal operation.
No change to registers setting.
10
0
RW
Disable Auto-MDI/MDI-X
1 = Disable Auto-MDI/MDI-X function.
0 = Enable Auto-MDI/MDI-X function.
Bit[3] in
P1MBCR
RW
Force MDI-X
1 = If Auto-MDI/MDI-X is disabled, force PHY into MDIX mode.
0 = Do not force PHY into MDI-X mode.
Bit[4] in
P1MBCR
RW
Far-End Loopback
1 = Perform loopback, as indicated:
Start: RXP2/RXM2 (port 2).
Loopback: PMD/PMA of port 1’s PHY.
End: TXP2/TXM2 (port 2).
0 = Normal operation.
Bit[14] in
P1MBCR
9
8
0
0
DS00002642A-page 112
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-57:
Bit
Default
7
1
6
1
5
1
4
1
3
1
2
1
1
1
0
4.2.8.11
PORT 1 CONTROL REGISTER 4 (0X07E – 0X07F): P1CR4 (CONTINUED)
1
R/W
Description
Bit is Same As
RW
Auto-Negotiation Enable
1 = Auto-negotiation is enabled.
0 = Disable auto-negotiation, speed, and duplex are
decided by bits[6:5] of the same register.
Bit[12] in
P1MBCR
RW
Force Speed
1 = Force 100BASE-TX if auto-negotiation is disabled
(bit[7]).
0 = Force 10BASE-T if auto-negotiation is disabled
(bit[7]).
Bit[13] in
P1MBCR
RW
Force Duplex
1 = Force full-duplex if auto-negotiation is disabled.
0 = Force half-duplex if auto-negotiation is disabled.
It is always in half-duplex if auto-negotiation is enabled
but failed.
Bit[8] in
P1MBCR
RW
Advertised Flow Control Capability
1 = Advertise flow control (pause) capability.
0 = Suppress flow control (pause) capability from
transmission to link partner.
Bit[10] in
P1ANAR
RW
Advertised 100BASE-TX Full-Duplex Capability
1 = Advertise 100BASE-TX full-duplex capability.
0 = Suppress 100BASE-TX full-duplex capability from
transmission to link partner.
Bit [8] in
P1ANAR
RW
Advertised 100BASE-TX Half-Duplex Capability
1 = Advertise 100BASE-TX half-duplex capability.
0 = Suppress 100BASE-TX half-duplex capability from
transmission to link partner.
Bit[7] in
P1ANAR
RW
Advertised 10BASE-T Full-Duplex Capability
1 = Advertise 10BASE-T full-duplex capability.
0 = Suppress 10BASE-T full-duplex capability from
transmission to link partner.
Bit[6] in
P1ANAR
RW
Advertised 10BASE-T Half-Duplex Capability
1 = Advertise 10BASE-T half-duplex capability.
0 = Suppress 10BASE-T half-duplex capability from
transmission to link partner.
Bit[5] in
P1ANAR
Port 1 Status Register (0x080 – 0x081): P1SR
This register contains status bits for the switch port 1 function.
TABLE 4-58:
PORT 1 STATUS REGISTER (0X080 – 0X081): P1SR
Bit
Default
R/W
Description
15
1
RW
HP_Mdix
1 = HP Auto-MDI-X mode.
0 = Microchip Auto-MDI-X mode.
14
0
RO
Reserved
13
0
RO
Polarity Reverse
1 = Polarity is reversed.
0 = Polarity is not reversed.
12
0
RO
Transmit Flow Control Enable
1 = Transmit flow control feature is active.
0 = Transmit flow control feature is inactive.
2018 Microchip Technology Inc.
Bit is Same As
Bit[5] in
P1MBCR
—
Bit[5] in
P1PHYCTRL
—
DS00002642A-page 113
KSZ8463ML/RL/FML/FRL
TABLE 4-58:
PORT 1 STATUS REGISTER (0X080 – 0X081): P1SR (CONTINUED)
Bit
Default
R/W
Description
Bit is Same As
11
0
RO
Receive Flow Control Enable
1 = Receive flow control feature is active.
0 = Receive flow control feature is inactive.
—
10
0
RO
Operation Speed
1 = Link speed is 100 Mbps.
0 = Link speed is 10 Mbps.
—
9
0
RO
Operation Duplex
1 = Link duplex is full.
0 = Link duplex is half.
—
8
0
RO
Far-End-Fault
1 = Far-end-fault detected.
0 = No far-end-fault detected.
For 100BASE-FX fiber mode operation.
7
0
RO
MDI-X Status
0 = MDI.
1 = MDI-X.
6
0
RO
Auto-Negotiation Done
1 = Auto-negotiation done.
0 = Auto-negotiation not done.
Bit[5] in
P1MBSR
5
0
RO
Link Status
1 = Link good.
0 = Link not good.
Bit[2] in
P1MBSR
4
0
RO
Partner Flow Control Capability
1 = Link partner flow control (pause) capable.
0 = Link partner not flow control (pause) capable.
Bit[10] in
P1ANLPR
3
0
RO
Partner 100BASE-TX Full-Duplex Capability
1 = Link partner 100BASE-TX full-duplex capable.
0 = Link partner not 100BASE-TX full-duplex capable.
Bit[8] in
P1ANLPR
2
0
RO
Partner 100BASE-TX Half-Duplex Capability
1 = Link partner 100BASE-TX half-duplex capable.
0= Link partner not 100BASE-TX half-duplex capable.
Bit[7] in
P1ANLPR
1
0
RO
Partner 10BASE-T Full-Duplex Capability
1= Link partner 10BASE-T full-duplex capable.
0 = Link partner not 10BASE-T full-duplex capable.
Bit[6] in
P1ANLPR
0
0
RO
Partner 10BASE-T Half-Duplex Capability
1 = Link partner 10BASE-T half-duplex capable.
0 = Link partner not 10BASE-T half-duplex capable.
Bit[5] in
P1ANLPR
4.2.8.12
4.2.9
4.2.9.1
Bit[4] in
P1MBSR
Bit[4] in
P1PHYCTRL
0x082 – 0x083: Reserved
PORT 2 CONTROL REGISTERS
Port 2 Control Register 1 (0x084 – 0x085): P2CR1
This register contains control bits for the switch port 2 function.
TABLE 4-59:
PORT 2 CONTROL REGISTER 1 (0X084 – 0X085): P2CR1
Bit
Default
R/W
Description
15
0
RO
Reserved
DS00002642A-page 114
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-59:
Bit
14 - 12
11
PORT 2 CONTROL REGISTER 1 (0X084 – 0X085): P2CR1 (CONTINUED)
Default
000
0
R/W
Description
RW
Port 2 LED Direct Control
These bits directly control the port 2 LED pins.
0xx = Normal LED function as set up via Reg. 0x00E – 0x00F, Bit[9:8].
100 = Both port 2 LEDs off.
101 = Port 2 LED1 off, LED0 on.
110 = Port 2 LED1 on, LED0 off.
111 = Both port 2 LEDs on.
RW
Source Address Filtering Enable for MAC Address 2
1 = Enable the source address filtering function when the SA matches
MAC Address 2 in SAFMACA2 (0x0B6 – 0x0BB).
0 = Disable source address filtering function.
10
0
RW
Source Address Filtering Enable for MAC Address 1
1 = Enable the source address filtering function when the SA matches
MAC Address 1 in SAFMACA1 (0x0B0 – 0x0B5).
0 = Disable source address filtering function.
9
0
RW
Drop Tagged Packet Enable
1 = Enable dropping of tagged ingress packets.
0 = Disable dropping of tagged ingress packets.
8
0
RW
TX Two Queues Select Enable
1 = The port 2 output queue is split into two priority queues (q0 and q1)
0 = Single output queue on port 2. There is no priority differentiation even
though packets are classified into high or low priority.
7
0
RW
Broadcast Storm Protection Enable
1 = Enable broadcast storm protection for ingress packets on port 2.
0 = Disable broadcast storm protection.
6
0
RW
Diffserv Priority Classification Enable
1 = Enable DiffServ priority classification for ingress packets on port 2.
0 = Disable DiffServ function.
5
0
RW
802.1p Priority Classification Enable
1 = Enable 802.1p priority classification for ingress packets on port 2.
0 = Disable 802.1p.
RW
Port-Based Priority Classification
00 = Ingress packets on port 2 are classified as priority 0 queue if “DiffServ” or “802.1p” classification is not enabled or fails to classify.
01 = Ingress packets on port 2 are classified as priority 1 queue if “DiffServ” or “802.1p” classification is not enabled or fails to classify.
10 = Ingress packets on port 2 are classified as priority 2 queue if “DiffServ” or “802.1p” classification is not enabled or fails to classify.
11 = Ingress packets on port 2 are classified as priority 3 queue if “Diffserv” or “802.1p” classification is not enabled or fails to classify.
Note: “DiffServ”, “802.1p” and port priority can be enabled at the same
time. The OR’ed result of 802.1p and DSCP overwrites the port priority.
RW
Tag Insertion
1 = When packets are output on port 2, the switch adds 802.1p/q tags to
packets without 802.1p/q tags when received. The switch will not add
tags to packets already tagged. The tag inserted is the ingress port’s
“port VID”.
0 = Disable tag insertion.
RW
Tag Removal
1 = When packets are output on port 2, the switch removes 802.1p/q tags
from packets with 802.1p/q tags when received. The switch will not modify packets received without tags.
0 = Disable tag removal.
4-3
2
1
00
0
0
2018 Microchip Technology Inc.
DS00002642A-page 115
KSZ8463ML/RL/FML/FRL
TABLE 4-59:
Bit
0
PORT 2 CONTROL REGISTER 1 (0X084 – 0X085): P2CR1 (CONTINUED)
Default
0
DS00002642A-page 116
R/W
Description
RW
TX Multiple Queues Select Enable
1 = The port 2 output queue is split into four priority queues (q0, q1, q2
and q3).
0 = Single output queue on port 2. There is no priority differentiation even
though packets are classified into high or low priority.
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.9.2
Port 2 Control Register 2 (0x086 – 0x087): P2CR2
This register contains control bits for the switch port 2 function.
TABLE 4-60:
PORT 2 CONTROL REGISTER 2 (0X086 – 0X087): P2CR2
Bit
Default
R/W
Description
15
0
RW
Reserved
RW
Ingress VLAN Filtering
1 = The switch discards packets whose VID port membership in VLAN
table bits [18:16] does not include the ingress port VID.
0 = No ingress VLAN filtering.
RW
Discard Non PVID Packets
1 = The switch discards packets whose VID does not match the ingress
port default VID.
0 = No packets are discarded.
14
13
0
0
12
0
RW
Force Flow Control
1 = Always enable flow control on the port, regardless of auto-negotiation
result.
0 = The flow control is enabled based on auto-negotiation result.
11
0
RW
Back Pressure Enable
1 = Enable port’s half-duplex back pressure.
0 = Disable port’s half-duplex back pressure.
10
1
RW
Transmit Enable
1 = Enable packet transmission on the port.
0 = Disable packet transmission on the port.
9
1
RW
Receive Enable
1 = Enable packet reception on the port.
0 = Disable packet reception on the port.
8
0
RW
Learning Disable
1 = Disable switch address learning capability.
0 = Enable switch address learning.
RW
Sniffer Port
1 = Port is designated as a sniffer port and transmits packets that are
monitored.
0 = Port is a normal port.
RW
Receive Sniff
1 = All packets received on the port are marked as “monitored packets”
and forwarded to the designated “sniffer port.”
0 = No receive monitoring.
7
6
0
0
5
0
RW
Transmit Sniff
1 = All packets transmitted on the port are marked as “monitored packets” and forwarded to the designated “sniffer port.”
0 = No transmit monitoring.
4
0
RW
Reserved
RW
User Priority Ceiling
1 = If the packet’s “priority field” is greater than the “user priority field” in
the port VID control register bit[15:13], replace the packet’s “priority field”
with the “user priority field” in the port VID control register bit[15:13].
0 = Do not compare and replace the packet’s “priority field.”
RW
Port VLAN Membership
Define the port’s port VLAN membership. Bit[2] stands for the host port,
bit[1] for port 2, and bit[0] for port 1. The port can only communicate
within the membership. A ‘1’ includes a port in the membership; a ‘0’
excludes a port from the membership.
3
2-0
0
111
2018 Microchip Technology Inc.
DS00002642A-page 117
KSZ8463ML/RL/FML/FRL
4.2.9.3
Port 2 VID Control Register (0x088 – 0x089): P2VIDCR
This register contains control bits for the switch port 2 function. This register has two main uses. It is associated with the
ingress of untagged packets and used for egress tagging as well as being used for address lookup and providing a
default VID for the ingress of untagged or null-VID-tagged packets.
TABLE 4-61:
PORT 2 VID CONTROL REGISTER (0X088 – 0X089): P2VIDCR
Bit
Default
R/W
Description
15 - 13
000
RW
Default Tag[15:13]
Port’s default tag, containing “User Priority Field” bits.
12
0
RW
Default Tag[12]
Port’s default tag, containing CFI bit.
11 - 0
0x001
RW
Default Tag[11:0]
Port’s default tag, containing VID[11:0].
4.2.9.4
Port 2 Control Register 3 (0x08A – 0x08B): P2CR3
This register contains the control bits for the switch port 2 function.
TABLE 4-62:
PORT 2 CONTROL REGISTER 3 (0X08A – 0X08B): P2CR3
Bit
Default
R/W
Description
15 - 5
0x000
RO
Reserved
4
0
RW
Reserved
RW
Ingress Limit Mode
These bits determine what kinds of frames are limited and counted
against ingress rate limiting as follows:
00 = Limit and count all frames.
01 = Limit and count Broadcast, Multicast, and flooded Unicast frames.
10 = Limit and count Broadcast and Multicast frames only.
11 = Limit and count Broadcast frames only.
RW
Count Inter-Frame Gap
Count IFG Bytes.
1 = Each frame’s minimum inter frame gap. IFG bytes (12 per frame) are
included in Ingress and Egress rate limiting calculations.
0 = IFG bytes are not counted.
RW
Count Preamble
Count preamble Bytes.
1 = Each frame’s preamble bytes (8 per frame) are included in Ingress
and Egress rate limiting calculations.
0 = Preamble bytes are not counted.
3-2
00
1
0
0
4.2.9.5
0
Port 2 Ingress Rate Control Register 0 (0x08C – 0x08D): P2IRCR0
This register contains the port 2 ingress rate limiting control bits for priority 1 and priority 0.
TABLE 4-63:
PORT 2 INGRESS RATE CONTROL REGISTER 0 (0X08C – 0X08D): P2IRCR0
Bit
Default
R/W
Description
15
0
RW
Reserved
14 - 8
0x00
RW
Ingress Data Rate Limit for Priority 1 Frames
Ingress priority 1 frames will be limited or discarded as shown in Table 452.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
7
0
RW
Reserved
DS00002642A-page 118
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-63:
Bit
Default
6-0
4.2.9.6
PORT 2 INGRESS RATE CONTROL REGISTER 0 (0X08C – 0X08D): P2IRCR0
0x00
R/W
Description
RW
Ingress Data Rate Limit for Priority 0 Frames
Ingress priority 0 frames will be limited or discarded as shown in Table 452.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
Port 2 Ingress Rate Control Register 1 (0x08E – 0x08F): P2IRCR1
This register contains the port 2 ingress rate limiting control bits for priority 3 and priority 2.
TABLE 4-64:
PORT 2 INGRESS RATE CONTROL REGISTER 1 (0X08E – 0X08F): P2IRCR1
Bit
Default
R/W
Description
15
0
RW
Reserved
14 - 8
0x00
RW
Ingress Data Rate Limit for Priority 3 Frames
Ingress priority 3 frames will be limited or discarded as shown in Table 452.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
7
0
RW
Reserved
RW
Ingress Data Rate Limit for Priority 2 Frames
Ingress priority 2 frames will be limited or discarded as shown in Table 452.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
6-0
4.2.9.7
0x00
Port 2 Egress Rate Control Register 0 (0x090 – 0x091): P2ERCR0
This register contains the port 2 egress rate limiting control bits for priority 1 and priority 0. When this port is configured
for 1 egress queue (which is the default), only the Priority 0 rate limit is applied. When it is configured for 2 queues, only
the Priority 1 and Priority 0 settings are applied.
TABLE 4-65:
PORT 2 EGRESS RATE CONTROL REGISTER 0 (0X090 – 0X091): P2ERCR0
Bit
Default
R/W
Description
15
0
RW
Reserved
14 - 8
0x00
RW
Egress Data Rate Limit for Priority 1 Frames
Egress priority 1 frames will be limited as shown in Table 4-52.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
7
0
RW
Reserved
RW
Egress Data Rate Limit for Priority 0 Frames
Egress priority 0 frames will be limited as shown in Table 4-52.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
6-0
4.2.9.8
0x00
Port 2 Egress Rate Control Register 1 (0x092 – 0x093): P2ERCR1
This register contains the port 2 egress rate limiting control bits for priority 3 and priority 2. When this port is configured
for 1 egress queue (which is the default), only the Priority 0 rate limit is applied. When it is configured for 2 queues, only
the Priority 1 and Priority 0 settings are applied.
TABLE 4-66:
PORT 2 EGRESS RATE CONTROL REGISTER 1 (0X092 – 0X093): P2ERCR1
Bit
Default
R/W
Description
15
0
RW
Reserved
2018 Microchip Technology Inc.
DS00002642A-page 119
KSZ8463ML/RL/FML/FRL
TABLE 4-66:
Bit
PORT 2 EGRESS RATE CONTROL REGISTER 1 (0X092 – 0X093): P2ERCR1
Default
R/W
Description
14 - 8
0x00
RW
Egress Data Rate Limit for Priority 3 Frames
Egress priority 3 frames will be limited as shown in Table 4-52.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
7
0
RW
Reserved
RW
Egress Data Rate Limit for Priority 2 Frames
Egress priority 2 frames will be limited as shown in Table 4-52.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
6-0
4.2.9.9
0x00
Port 2 PHY Special Control/Status, LinkMD® (0x094 – 0x095): P2SCSLMD
This register contains the LinkMD control and status information of PHY 2.
TABLE 4-67:
PORT 2 PHY SPECIAL CONTROL/STATUS, LINKMD® (0X094 – 0X095): P2SCSLMD
Bit
Default
R/W
Description
Bit is Same As
15
0
RO
CDT_10m_Short
1 = Less than 10 meter short.
Bit[12] in MIIM
PHYAD = 0x2,
0x1D
RO
Cable Diagnostic Results
[00] = Normal condition.
[01] = Open condition has been detected in cable.
[10] = Short condition has been detected in cable.
[11] = Cable diagnostic test has failed.
Bits[14:13] in
MIIM
PHYAD = 0x2,
0x1D
Cable Diagnostic Test Enable
1 = Cable diagnostic test is enabled. It is self-cleared
after the test is done.
0 = Indicates that the cable diagnostic test has completed and the status information is valid for reading.
Bit[15] in MIIM
PHYAD = 0x2,
0x1D
Bit[3] in
P2PHYCTRL
14 - 13
00
12
0
RW/SC
11
0
RW
Force_Link
Force link.
1 = Force link pass.
0 = Normal operation.
10
1
RW
Reserved
Bit[1] in
P2PHYCTRL
Bits[8:0] in MIIM
PHYAD = 0x2,
0x1D
—
9
0
RW
Remote (Near-End) Loopback
1 = Perform remote loopback at port 2's PHY (RXP2/
RXM2 -> TXP2/TXM2)
0 = Normal operation
8-0
0x000
RO
CDT_Fault_Count
Distance to the fault. It’s approximately 0.4m*CDT_Fault_Count.
4.2.9.10
Port 2 Control Register 4 (0x096 – 0x097): P2CR4
This register contains the control bits for the switch port 2 function.
TABLE 4-68:
PORT 2 CONTROL REGISTER 4 (0X096 – 0X097): P2CR4
Bit
Default
R/W
Description
15
0
RW
Reserved
14
0
RW
DisableTransmit
1 = Disable the port’s transmitter.
0 = Normal operation.
DS00002642A-page 120
Bit is Same As
—
Bit[1] in
P2MBCR
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-68:
PORT 2 CONTROL REGISTER 4 (0X096 – 0X097): P2CR4 (CONTINUED)
Bit
Default
R/W
13
0
RW/SC
12
0
Description
Bit is Same As
Restart Auto-Negotiation
1 = Restart auto-negotiation.
0 = Normal operation.
Bit[9] in
P2MBCR
RW
Disable Far-End-Fault
1 = Disable far-end-fault detection.
0 = Normal operation.
For 100BASE-FX fiber-mode operation.
Bit[2] in
P2MBCR
Bit[11] in
P2MBCR
11
0
RW
Power Down
1 = Power down.
0 = Normal operation.
No change to registers setting
10
0
RW
Disable Auto-MDI/MDI-X
1 = Disable Auto-MDI/MDI-X function.
0 = Enable Auto- MDI/MDI-X function.
Bit[3] in
P2MBCR
RW
Force MDI-X
1 = If Auto-MDI/MDI-X is disabled, force PHY into MDIX mode.
0 = Do not force PHY into MDI-X mode.
Bit[4] in
P2MBCR
RW
Far-End Loopback
1 = Perform loopback, as indicated:
Start: RXP1/RXM1 (port 1).
Loopback: PMD/PMA of port 2’s PHY.
End: TXP1/TXM1 (port 1).
0 = Normal operation.
Bit[14] in
P2MBCR
RW
Auto-Negotiation Enable
1 = Auto-negotiation is enabled.
0 = Disable auto-negotiation, speed, and duplex are
decided by bits [6:5] of the same register.
Bit[12] in
P2MBCR
RW
Force Speed
1 = Force 100BASE-TX if auto-negotiation is disabled
(bit[7]).
0 = Force 10BASE-T if auto-negotiation is disabled
(bit[7]).
Bit[13] in
P2MBCR
RW
Force Duplex
1 = Force full-duplex if auto-negotiation is disabled.
0 = Force half-duplex if auto-negotiation is disabled.
It is always in half-duplex if auto-negotiation is enabled
but failed.
Bit[8] in
P2MBCR
RW
Advertised Flow Control Capability
1 = Advertise flow control (pause) capability.
0 = Suppress flow control (pause) capability from
transmission to link partner.
Bit[10] in
P2ANAR
RW
Advertised 100BASE-TX Full-Duplex Capability
1 = Advertise 100BASE-TX full-duplex capability.
0 = Suppress 100BASE-TX full-duplex capability from
transmission to link partner.
Bit[8] in
P2ANAR
RW
Advertised 100BASE-TX Half-Duplex Capability
1 = Advertise 100BASE-TX half-duplex capability.
0 = Suppress 100BASE-TX half-duplex capability from
transmission to link partner.
Bit[7] in
P2ANAR
9
8
7
6
5
4
3
2
0
0
1
1
1
1
1
1
2018 Microchip Technology Inc.
DS00002642A-page 121
KSZ8463ML/RL/FML/FRL
TABLE 4-68:
Bit
Default
1
1
0
4.2.9.11
PORT 2 CONTROL REGISTER 4 (0X096 – 0X097): P2CR4 (CONTINUED)
1
R/W
Description
Bit is Same As
RW
Advertised 10BASE-T Full-Duplex Capability
1 = Advertise 10BASE-T full-duplex capability.
0 = Suppress 10BASE-T full-duplex capability from
transmission to link partner.
Bit[6] in
P2ANAR
RW
Advertised 10BASE-T Half-Duplex Capability
1 = Advertise 10BASE-T half-duplex capability.
0 = Suppress 10BASE-T half-duplex capability from
transmission to link partner.
Bit[5] in
P2ANAR
Port 2 Status Register (0x098 – 0x099): P2SR
This register contains status bits for the switch port 2 function.
TABLE 4-69:
PORT 2 STATUS REGISTER (0X098 – 0X099): P2SR
Bit
Default
R/W
Description
Bit is Same As
15
1
RW
HP_MDIX
1 = HP Auto-MDI-X mode.
0 = Microchip Auto-MDI-X mode.
14
0
RO
Reserved
13
0
RO
Polarity Reverse
1 = Polarity is reversed.
0 = Polarity is not reversed.
12
0
RO
Transmit Flow Control Enable
1 = Transmit flow control feature is active.
0 = Transmit flow control feature is inactive.
—
11
0
RO
Receive Flow Control Enable
1 = Receive flow control feature is active.
0 = Receive flow control feature is inactive.
—
10
0
RO
Operation Speed
1 = Link speed is 100 Mbps.
0 = Link speed is 10 Mbps.
—
9
0
RO
Operation Duplex
1 = Link duplex is full.
0 = Link duplex is half.
—
Bit[5] in
P2MBCR
—
Bit[5] in
P2PHYCTRL
8
0
RO
Far-End-Fault
1 = Far-end-fault detected.
0 = No far-end-fault detected.
For 100BASE-FX fiber mode operation.
7
0
RO
MDI-X status
0 = MDI.
1 = MDI-X.
6
0
RO
Auto-Negotiation Done
1 = Auto-negotiation done.
0 = Auto-negotiation not done.
Bit[5] in
P2MBSR
5
0
RO
Link Status
1 = Link good.
0 = Link not good.
Bit[2] in
P2MBSR
4
0
RO
Partner Flow Control Capability
1 = Link partner flow control (pause) capable.
0 = Link partner not flow control (pause) capable.
Bit[10] in
P2ANLPR
3
0
RO
Partner 100BASE-TX Full-Duplex Capability
1 = Link partner 100BASE-TX full-duplex capable.
0 = Link partner not 100BASE-TX full-duplex capable.
Bit[8] in
P2ANLPR
DS00002642A-page 122
Bit[4] in
P2MBSR
Bit[4] in
P2PHYCTRL
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-69:
PORT 2 STATUS REGISTER (0X098 – 0X099): P2SR (CONTINUED)
Bit
Default
R/W
Description
2
0
RO
Partner 100BASE-TX Half-Duplex Capability
1 = Link partner 100BASE-TX half-duplex capable.
0= Link partner not 100BASE-TX half-duplex capable.
Bit[7] in
P2ANLPR
1
0
RO
Partner 10BASE-T Full-Duplex Capability
1= Link partner 10BASE-T full-duplex capable.
0 = Link partner not 10BASE-T full-duplex capable.
Bit[6] in
P2ANLPR
0
0
RO
Partner 10BASE-T Half-Duplex Capability
1 = Link partner 10BASE-T half-duplex capable.
0 = Link partner not 10BASE-T half-duplex capable.
Bit[5] in
P2ANLPR
4.2.9.12
4.2.10
4.2.10.1
Bit is Same As
0x09A – 0x09B: Reserved
PORT 3 CONTROL REGISTERS
Port 3 Control Register 1 (0x09C – 0x09D): P3CR1
This register contains control bits for the switch port 3 function.
TABLE 4-70:
PORT 3 CONTROL REGISTER 1 (0X09C – 0X09D): P3CR1
Bit
Default
R/W
Description
15 - 10
0x00
RO
Reserved
9
0
RW
Drop Tagged Packet Enable
1 = Enable dropping of tagged ingress packets.
0 = Disable dropping of tagged ingress packets.
8
0
RW
TX Two Queues Select Enable
1 = The port 3 output queue is split into two priority queues (q0 and q1).
0 = Single output queue on port 3. There is no priority differentiation even
though packets are classified into high or low priority.
7
0
RW
Broadcast Storm Protection Enable
1 = Enable broadcast storm protection for ingress packets on port 3.
0 = Disable broadcast storm protection.
6
0
RW
Diffserv Priority Classification Enable
1 = Enable DiffServ priority classification for ingress packets on port 3.
0 = Disable DiffServ function.
5
0
RW
802.1p Priority Classification Enable
1 = Enable 802.1p priority classification for ingress packets on port 3.
0 = Disable 802.1p.
RW
Port-Based Priority Classification
00 = Ingress packets on port 3 are classified as priority 0 queue if “DiffServ” or “802.1p” classification is not enabled or fails to classify.
01 = Ingress packets on port 3 are classified as priority 1 queue if “DiffServ” or “802.1p” classification is not enabled or fails to classify.
10 = Ingress packets on port 3 are classified as priority 2 queue if “DiffServ” or “802.1p” classification is not enabled or fails to classify.
11 = Ingress packets on port 3 are classified as priority 3 queue if “Diffserv” or “802.1p” classification is not enabled or fails to classify.
Note: “DiffServ”, “802.1p” and port priority can be enabled at the same
time. The OR’ed result of 802.1p and DSCP overwrites the port priority.
RW
Tag Insertion
1 = When packets are output on port 3, the switch adds 802.1p/q tags to
packets without 802.1p/q tags when received. The switch will not add
tags to packets already tagged. The tag inserted is the ingress port’s
“port VID”.
0 = Disable tag insertion.
4-3
2
00
0
2018 Microchip Technology Inc.
DS00002642A-page 123
KSZ8463ML/RL/FML/FRL
TABLE 4-70:
Bit
Default
1
0
0
4.2.10.2
PORT 3 CONTROL REGISTER 1 (0X09C – 0X09D): P3CR1 (CONTINUED)
0
R/W
Description
RW
Tag Removal
1 = When packets are output on port 3, the switch removes 802.1p/q tags
from packets with 802.1p/q tags when received. The switch will not modify packets received without tags.
0 = Disable tag removal.
RW
TX Multiple Queues Select Enable
1 = The port 3 output queue is split into four priority queues (q0, q1, q2
and q3).
0 = Single output queue on port 3. There is no priority differentiation even
though packets are classified into high or low priority.
Port 3 Control Register 2 (0x09E – 0x09F): P3CR2
This register contains control bits for the switch port 3 function.
TABLE 4-71:
PORT 3 CONTROL REGISTER 2 (0X09E – 0X09F): P3CR2
Bit
Default
R/W
15
0
RW
Reserved
RW
Ingress VLAN Filtering
1 = The switch discards packets whose VID port membership in VLAN
table bits [18:16] does not include the ingress port VID.
0 = No ingress VLAN filtering.
Discard Non PVID Packets
1 = The switch discards packets whose VID does not match the ingress
port default VID.
0 = No packets are discarded.
14
0
Description
13
0
RW
12
0
RW
Reserved
11
0
RW
Back Pressure Enable
1 = Enable port’s half-duplex back pressure.
0 = Disable port’s half-duplex back pressure.
10
1
RW
Transmit Enable
1 = Enable packet transmission on the port.
0 = Disable packet transmission on the port.
9
1
RW
Receive Enable
1 = Enable packet reception on the port.
0 = Disable packet reception on the port.
8
0
RW
Learning Disable
1 = Disable switch address learning capability.
0 = Enable switch address learning.
RW
Sniffer Port
1 = Port is designated as a sniffer port and transmits packets that are
monitored.
0 = Port is a normal port.
RW
Receive Sniff
1 = All packets received on the port are marked as “monitored packets”
and forwarded to the designated “sniffer port.”
0 = No receive monitoring.
7
6
0
0
5
0
RW
Transmit Sniff
1 = All packets transmitted on the port are marked as “monitored packets” and forwarded to the designated “sniffer port.”
0 = No transmit monitoring.
4
0
RW
Reserved
DS00002642A-page 124
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-71:
Bit
Default
3
0
2-0
4.2.10.3
PORT 3 CONTROL REGISTER 2 (0X09E – 0X09F): P3CR2 (CONTINUED)
111
R/W
Description
RW
User Priority Ceiling
1 = If the packet’s “priority field” is greater than the “user priority field” in
the port VID control register bit[15:13], replace the packet’s “priority field”
with the “user priority field” in the port VID control register bit[15:13].
0 = Do not compare and replace the packet’s “priority field.”
RW
Port VLAN Membership
Define the port’s port VLAN membership. Bit[2] stands for the host port,
bit [1] for port 2, and bit [0] for port 1. The port can only communicate
within the membership. A ‘1’ includes a port in the membership; a ‘0’
excludes a port from the membership.
Port 3 VID Control Register (0x0A0 – 0x0A1): P3VIDCR
This register contains the control bits for the switch port 3 function. This register has two main uses. It is associated with
the ingress of untagged packets and used for egress tagging as well as being used for address lookup and providing a
default VID for the ingress of untagged or null-VID-tagged packets.
TABLE 4-72:
PORT 3 VID CONTROL REGISTER (0X0A0 – 0X0A1): P3VIDCR
Bit
Default
R/W
Description
15 - 13
0x0
RW
Default Tag[15:13]
Port’s default tag, containing “User Priority Field” bits.
12
0
RW
Default Tag[12]
Port’s default tag, containing CFI bit.
11 - 0
0x001
RW
Default Tag[11:0]
Port’s default tag, containing VID[11:0].
4.2.10.4
Port 3 Control Register 3 (0x0A2 – 0x0A3): P3CR3
This register contains the control bits for the switch port 3 function.
TABLE 4-73:
PORT 3 CONTROL REGISTER 3 (0X0A2 – 0X0A3): P3CR3
Bit
Default
R/W
Description
15 - 8
0x00
RO
Reserved
7
—
RW
Port 3 MAC Mode
The RX_DV (pin 31) value is latched into this bit during power-up/reset.
1 = MAC MII mode.
0 = PHY MII mode.
6-4
000
RW
Reserved
RW
Ingress Limit Mode
These bits determine what kinds of frames are limited and counted
against ingress rate limiting as follows:
00 = Limit and count all frames.
01 = Limit and count Broadcast, Multicast, and flooded Unicast frames.
10 = Limit and count Broadcast and Multicast frames only.
11 = Limit and count Broadcast frames only.
RW
Count Inter-Frame Gap
Count IFG Bytes.
1 = Each frame’s minimum inter frame gap. IFG bytes (12 per frame) are
included in Ingress and Egress rate limiting calculations.
0 = IFG bytes are not counted.
RW
Count Preamble
Count preamble Bytes.
1 = Each frame’s preamble bytes (8 per frame) are included in Ingress
and Egress rate limiting calculations.
0 = Preamble bytes are not counted.
3-2
1
0
00
0
0
2018 Microchip Technology Inc.
DS00002642A-page 125
KSZ8463ML/RL/FML/FRL
4.2.10.5
Port 3 Ingress Rate Control Register 0 (0x0A4 – 0x0A5): P3IRCR0
This register contains the port 3 ingress rate limiting control bits for priority 1 and priority 0.
TABLE 4-74:
PORT 3 INGRESS RATE CONTROL REGISTER 0 (0X0A4 – 0X0A5): P3IRCR0
Bit
Default
R/W
Description
15
0
RW
Reserved
RW
Ingress Data Rate Limit for Priority 1 Frames
Ingress priority 1 frames will be limited or discarded as shown in Table 452.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
RW
Sample Edge of REFCLK_I clock in Port 3 RMII Mode
The REFCLK input clock sample edge control.
0 = Use the rising edge of REFCLK clock to sample the input data in RMII
mode.
1 = Use the falling edge of REFCLK clock to sample the input data in
RMII mode.
RW
Ingress Data Rate Limit for Priority 0 Frames
Ingress priority 0 frames will be limited or discarded as shown in Table 452.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
14 - 8
0x00
7
0
6-0
4.2.10.6
0x00
Port 3 Ingress Rate Control Register 1 (0x0A6 – 0x0A7): P3IRCR1
This register contains the port 3 ingress rate limiting control bits for priority 3 and priority 2.
TABLE 4-75:
PORT 3 INGRESS RATE CONTROL REGISTER 1 (0X0A6 – 0X0A7): P3IRCR1
Bit
Default
R/W
Description
15
0
RW
Reserved
14 - 8
0x00
RW
Ingress Data Rate Limit for Priority 3 Frames
Ingress priority 3 frames will be limited or discarded as shown in Table 452.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
7
0
RW
Reserved
RW
Ingress Data Rate Limit for Priority 2 Frames
Ingress priority 2 frames will be limited or discarded as shown in Table 452.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
6-0
4.2.10.7
0x00
Port 3 Egress Rate Control Register 0 (0x0A8 – 0x0A9): P3ERCR0
This register contains the port 3 egress rate limiting control bits for priority 1 and priority 0. When this port is configured
for 1 egress queue (which is the default), only the Priority 0 rate limit is applied. When it is configured for 2 queues, only
the Priority 1 and Priority 0 settings are applied.
TABLE 4-76:
PORT 3 EGRESS RATE CONTROL REGISTER 0 (0X0A8 – 0X0A9): P3ERCR0
Bit
Default
R/W
15
0
RW
Reserved
RW
Egress Data Rate Limit for Priority 1 Frames
Egress priority 1 frames will be limited as shown in Table 4-52.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
14 - 8
0x00
DS00002642A-page 126
Description
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-76:
PORT 3 EGRESS RATE CONTROL REGISTER 0 (0X0A8 – 0X0A9): P3ERCR0
Bit
Default
R/W
Description
7
0
RW
Egress Rate Limit Control Enable
1 = Enable egress rate limit control.
0 = Disable egress rate limit control.
RW
Egress Data Rate Limit for Priority 0 Frames
Egress priority 0 frames will be limited as shown in Table 4-52.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
6-0
4.2.10.8
0x00
Port 3 Egress Rate Control Register 1 (0x0AA – 0x0AB): P3ERCR1
This register contains the port 3 egress rate limiting control bits for priority 3 and priority 2. When this port is configured
for 1 egress queue (which is the default), only the Priority 0 rate limit is applied. When it is configured for 2 queues, only
the Priority 1 and Priority 0 settings are applied.
TABLE 4-77:
PORT 3 EGRESS RATE CONTROL REGISTER 1 (0X0AA – 0X0AB): P3ERCR1
Bit
Default
R/W
Description
15
0
RW
Reserved
14 - 8
0x00
RW
Egress Data Rate Limit for Priority 3 Frames
Egress priority 3 frames will be limited as shown in Table 4-52.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
7
0
RW
Reserved
RW
Egress Data Rate Limit for Priority 2 Frames
Egress priority 2 frames will be limited as shown in Table 4-52.
Note: The default value 0x00 is full rate at 10 Mbps or 100 Mbps with no
limit.
6-0
4.2.11
4.2.11.1
0x00
SWITCH GLOBAL CONTROL REGISTERS
Switch Global Control Register 8 (0x0AC – 0x0AD): SGCR8
This register contains the global control bits for the switch function.
TABLE 4-78:
Bit
SWITCH GLOBAL CONTROL REGISTER 8 (0X0AC – 0X0AD): SGCR8
Default
R/W
Description
Two Queue Priority Mapping
These bits determine the mapping between the priority of the incoming
frames and the destination on-chip queue in a two queue configuration
which uses egress queues 0 and 1.
15 - 14
10
RW
‘00’ = Reserved
‘01’ = Egress Queue 1 receives priority 1, 2, 3 frames
Egress Queue 0 receives priority 0 frames
‘10’ = (default) Reserved
‘11’ = Egress Queue 1 receives priority 1, 2, 3 frames
Egress Queue 0 receives priority 0 frames
13 - 11
000
RO
Reserved
10
0
RW/SC
9
0
RW
2018 Microchip Technology Inc.
Flush Dynamic MAC Table
Before flushing the dynamic MAC table, switch address learning must be
disabled by setting bit[8] in the P1CR2, P2CR2, and P3CR2 registers.
Flush Static MAC Table
1 = Enable flush static MAC table for spanning tree application.
0 = Disable flush static MAC table for spanning tree application.
DS00002642A-page 127
KSZ8463ML/RL/FML/FRL
TABLE 4-78:
SWITCH GLOBAL CONTROL REGISTER 8 (0X0AC – 0X0AD): SGCR8 (CONTINUED)
Bit
Default
R/W
Description
8
0
RW
Port 3 Tail-Tag Mode Enable
1 = Enable tail tag mode.
0 = Disable tail tag mode.
RW
Force PAUSE Off Iteration Limit Time Enable
0x01 – 0xFF = Enable to force PAUSE off iteration limit time (a unit number is 160 ms).
0x00 = Disable Force PAUSE Off Iteration Limit.
7-0
4.2.11.2
0x00
Switch Global Control Register 9 (0x0AE – 0x0AF): SGCR9
This register contains the global control bits for the switch function.
TABLE 4-79:
SWITCH GLOBAL CONTROL REGISTER 9 (0X0AE – 0X0AF): SGCR9
Bit
Default
R/W
Description
15 - 11
0x00
RO
Reserved
10 - 8
000
RW
Forwarding Invalid Frame
Define the forwarding port for frame with invalid VID. Bit[10] stands for
the host port, bit[9] for port 2, and bit[8] for port 1.
7-6
00
RW
Reserved
RW
Enable Insert Source Port PVID Tag when Untagged Frame from
Port 3 to Port 2
1 = Enable.
0 = Disable.
RW
Enable Insert Source Port PVID Tag when Untagged Frame from
Port 3 to Port 1
1 = Enable.
0 = Disable.
RW
Enable Insert Source Port PVID Tag when Untagged Frame from
Port 2 to Port 3
1 = Enable.
0 = Disable.
RW
Enable Insert Source Port PVID Tag when Untagged Frame from
Port 2 to Port 1
1 = Enable.
0 = Disable.
RW
Enable Insert Source Port PVID Tag when Untagged Frame from
Port 1 to Port 3
1 = Enable.
0 = Disable.
RW
Enable Insert Source Port PVID Tag when Untagged Frame from
Port 1 to Port 2
1 = Enable.
0 = Disable.
5
4
3
2
1
0
0
0
0
0
0
0
DS00002642A-page 128
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.12
4.2.12.1
SOURCE ADDRESS FILTERING MAC ADDRESS REGISTERS
Source Address Filtering MAC Address 1 Register Low (0x0B0 – 0x0B1): SAFMACA1L
The following table shows the register bit fields for the low word of MAC Address 1.
TABLE 4-80:
SOURCE ADDRESS FILTERING MAC ADDRESS 1 REGISTER LOW (0X0B0 –
0X0B1): SAFMACA1L
Bit
Default
R/W
Description
15 - 0
0x0000
RW
Source Filtering MAC Address 1 Low
The least significant word of MAC Address 1.
4.2.12.2
Source Address Filtering MAC Address 1 Register Middle (0x0B2 – 0x0B3): SAFMACA1M
The following table shows the register bit fields for the middle word of MAC Address 1.
TABLE 4-81:
SOURCE ADDRESS FILTERING MAC ADDRESS 1 REGISTER MIDDLE (0X0B2 –
0X0B3): SAFMACA1M
Bit
Default
R/W
Description
15 - 0
0x0000
RW
Source Filtering MAC Address Middle 1
The middle word of MAC Address 1.
4.2.12.3
Source Address Filtering MAC Address 1 Register High (0x0B4 – 0x0B5): SAFMACA1H
The following table shows the register bit fields for the high word of MAC Address 1.
TABLE 4-82:
SOURCE ADDRESS FILTERING MAC ADDRESS 1 REGISTER HIGH (0X0B4 –
0X0B5): SAFMACA1H
Bit
Default
R/W
Description
15 - 0
0x0000
RW
Source Filtering MAC Address 1 High
The most significant word of MAC Address 1.
4.2.12.4
Source Address Filtering MAC Address 2 Register Low (0x0B6 – 0x0B7): SAFMACA2L
The following table shows the register bit fields for the low word of MAC Address 2.
TABLE 4-83:
SOURCE ADDRESS FILTERING MAC ADDRESS 2 REGISTER LOW (0X0B6 –
0X0B7): SAFMACA2L
Bit
Default
R/W
Description
15 - 0
0x0000
RW
Source Filtering MAC Address Low 2
The least significant word of MAC Address 2.
4.2.12.5
Source Address Filtering MAC Address 2 Register Middle (0x0B8 – 0x0B9): SAFMACA2M
The following table shows the register bit fields for the middle word of MAC Address 2.
TABLE 4-84:
SOURCE ADDRESS FILTERING MAC ADDRESS 2 REGISTER MIDDLE (0X0B8 –
0X0B9): SAFMACA2M
Bit
Default
R/W
Description
15 - 0
0x0000
RW
Source Filtering MAC Address Middle 2
The middle word of MAC Address 2.
2018 Microchip Technology Inc.
DS00002642A-page 129
KSZ8463ML/RL/FML/FRL
4.2.12.6
Source Address Filtering MAC Address 2 Register High (0x0BA – 0x0BB): SAFMACA2H
The following table shows the register bit fields for the high word of MAC Address 2.
TABLE 4-85:
SOURCE ADDRESS FILTERING MAC ADDRESS 2 REGISTER HIGH (0X0BA –
0X0BB): SAFMACA2H
Bit
Default
R/W
Description
15 - 0
0x0000
RW
Source Filtering MAC Address High 2
The most significant word of MAC Address 2.
4.2.12.7
4.2.13
4.2.13.1
0x0BC – 0x0C7: Reserved
TXQ RATE CONTROL REGISTERS
Port 1 TXQ Rate Control Register 1 (0x0C8 – 0x0C9): P1TXQRCR1
This register contains the q2 and q3 rate control bits for port 1.
TABLE 4-86:
Bit
PORT 1 TXQ RATE CONTROL REGISTER 1 (0X0C8 – 0X0C9): P1TXQRCR1
Default
R/W
Description
15
1
RW
Port 1 Transmit Queue 2 (high) Ratio Control
0 = Strict priority. Port 1 will transmit all the packets from this priority q2
before transmit lower priority queue.
1 = Bit[14:8] reflect the number of packets allow to transmit from this priority q2 within a certain time.
14 - 8
0x04
RW
Port 1 Transmit Queue 2 (high) Ratio
This ratio indicates the number of packet for high priority packet can
transmit within a given period.
7
1
RW
Port 1 Transmit Queue 3 (highest) Ratio Control
0 = Strict priority. Port 1 will transmit all the packets from this priority q3
before transmit lower priority queue.
1 = Bit[6:0] reflect the number of packets allow to transmit from this priority q3 within a certain time.
6-0
0x08
RW
Port 1 Transmit Queue 3 (highest) Ratio
This ratio indicates the number of packet for highest priority packet can
transmit within a given period.
4.2.13.2
Port 1 TXQ Rate Control Register 2 (0x0CA – 0x0CB): P1TXQRCR2
This register contains the q0 and q1 rate control bits for port 1.
TABLE 4-87:
Bit
PORT 1 TXQ RATE CONTROL REGISTER 2 (0X0CA – 0X0CB): P1TXQRCR2
Default
R/W
Description
15
1
RW
Port 1 Transmit Queue 0 (lowest) Ratio Control
0 = Strict priority. Port 1 will transmit all the packets from this priority q0
after transmit higher priority queue.
1 = Bit[14:8] reflect the number of packets allow to transmit from this priority q0 within a certain time.
14 - 8
0x01
RW
Port 1 Transmit Queue 0 (lowest) Ratio
This ratio indicates the number of packet for lowest priority packet can
transmit within a given period.
RW
Port 1 Transmit Queue 1 (low) Ratio Control
0 = Strict priority. Port 1 will transmit all the packets from this priority q1
before transmit lower priority queue.
1 = Bit[6:0] reflect the number of packets allow to transmit from this priority q1 within a certain time.
7
1
DS00002642A-page 130
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-87:
PORT 1 TXQ RATE CONTROL REGISTER 2 (0X0CA – 0X0CB): P1TXQRCR2
Bit
Default
R/W
Description
6-0
0x02
RW
Port 1 Transmit Queue 1 (low) Ratio
This ratio indicates the number of packet for low priority packet can transmit within a given period.
4.2.13.3
Port 2 TXQ Rate Control Register 1 (0x0CC – 0x0CD): P2TXQRCR1
This register contains the q2 and q3 rate control bits for port 2.
TABLE 4-88:
Bit
PORT 2 TXQ RATE CONTROL REGISTER 1 (0X0CC – 0X0CD): P2TXQRCR1
Default
R/W
Description
15
1
RW
Port 2 Transmit Queue 2 (high) Ratio Control
0 = Strict priority. Port 2 will transmit all the packets from this priority q2
before transmit lower priority queue.
1 = Bit[14:8] reflect the number of packets allow to transmit from this priority q2 within a certain time.
14 - 8
0x04
RW
Port 2 Transmit Queue 2 (high) Ratio
This ratio indicates the number of packet for high priority packet can
transmit within a given period.
7
1
RW
Port 2 Transmit Queue 3 (highest) Ratio Control
0 = Strict priority. Port 2 will transmit all the packets from this priority q3
before transmit lower priority queue.
1 = Bit[6:0] reflect the number of packets allow to transmit from this priority q3 within a certain time.
6-0
0x08
RW
Port 2 Transmit Queue 3 (highest) Ratio
This ratio indicates the number of packet for highest priority packet can
transmit within a given period.
4.2.13.4
Port 2 TXQ Rate Control Register 2 (0x0CE – 0x0CF): P2TXQRCR2
This register contains the q0 and q1 rate control bits for port 2.
TABLE 4-89:
PORT 2 TXQ RATE CONTROL REGISTER 2 (0X0CE – 0X0CF): P2TXQRCR2
Bit
Default
R/W
Description
15
1
RW
Port 2 Transmit Queue 0 (lowest) Ratio Control
0 = Strict priority. Port 2 will transmit all the packets from this priority q0
after transmit higher priority queue.
1 = Bit[14:8] reflect the number of packets allow to transmit from this priority q0 within a certain time.
14 - 8
0x01
RW
Port 2 Transmit Queue 0 (lowest) Ratio
This ratio indicates the number of packet for lowest priority packet can
transmit within a given period.
7
1
RW
Port 2 Transmit Queue 1 (low) Ratio Control
0 = Strict priority. Port 2 will transmit all the packets from this priority q1
before transmit lower priority queue.
1 = Bit[6:0] reflect the number of packets allow to transmit from this priority q1 within a certain time.
6-0
0x02
RW
Port 2 Transmit Queue 1 (low) Ratio
This ratio indicates the number of packet for low priority packet can transmit within a given period.
2018 Microchip Technology Inc.
DS00002642A-page 131
KSZ8463ML/RL/FML/FRL
4.2.13.5
Port 3 TXQ Rate Control Register 1 (0x0D0 – 0x0D1): P3TXQRCR1
This register contains the q2 and q3 rate control bits for port 3.
TABLE 4-90:
Bit
PORT 3 TXQ RATE CONTROL REGISTER 1 (0X0D0 – 0X0D1): P3TXQRCR1
Default
R/W
Description
15
1
RW
Port 3 Transmit Queue 2 (high) Ratio Control
0 = Strict priority. Port 3 will transmit all the packets from this priority q2
before transmit lower priority queue.
1 = Bit[14:8] reflect the number of packets allow to transmit from this priority q2 within a certain time.
14 - 8
0x04
RW
Port 3 Transmit Queue 2 (high) Ratio
This ratio indicates the number of packet for high priority packet can
transmit within a given period.
7
1
RW
Port 3 Transmit Queue 3 (highest) Ratio Control
0 = Strict priority. Port 3 will transmit all the packets from this priority q3
before transmit lower priority queue.
1 = Bit[6:0] reflect the number of packets allow to transmit from this priority q3 within a certain time.
6-0
0x08
RW
Port 3 Transmit Queue 3 (highest) Ratio
This ratio indicates the number of packet for highest priority packet can
transmit within a given period.
4.2.13.6
Port 3 TXQ Rate Control Register 2 (0x0D2 – 0x0D3): P3TXQRCR2
This register contains the q0 and q1 rate control bits for port 3.
TABLE 4-91:
Bit
PORT 3 TXQ RATE CONTROL REGISTER 2 (0X0D2 – 0X0D3): P3TXQRCR2
Default
R/W
Description
15
1
RW
Port 3 Transmit Queue 0 (lowest) Ratio Control
0 = Strict priority. Port 3 will transmit all the packets from this priority q0
after transmit higher priority queue.
1 = Bit[14:8] reflect the number of packets allow to transmit from this priority q0 within a certain time.
14 - 6
0x01
RW
Port 3 Transmit Queue 0 (lowest) Ratio
This ratio indicates the number of packet for lowest priority packet can
transmit within a given period.
7
1
RW
Port 3 Transmit Queue 1 (low) Ratio Control
0 = Strict priority. Port 3 will transmit all the packets from this priority q1
before transmit lower priority queue.
1 = Bit[6:0] reflect the number of packets allow to transmit from this priority q1 within a certain time.
6-0
0x02
RW
Port 3 Transmit Queue 1 (low) Ratio
This ratio indicates the number of packet for low priority packet can transmit within a given period.
4.2.13.7
4.2.14
4.2.14.1
0x0D4 – 0x0D5: Reserved
INPUT AND OUTPUT MULTIPLEX SELECTION REGISTER
Input and Output Multiplex Selection Register (0x0D6 – 0x0D7): IOMXSEL
This register is used to select the functionality of pins 59, 61, and 62. Note that further programmability of the LED function is controlled via bits [9:8] in the SGCR7 Control register.
DS00002642A-page 132
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-92:
INPUT AND OUTPUT MULTIPLEX SELECTION REGISTER (0X0D6 – 0X0D7):
IOMXSEL
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
11
1
RW
Reserved
10
1
RW
Selection of P2LED1 or GPIO9 on Pin 61
1 = This pin is used for P2LED1 (default).
0 = This pin is used for GPIO9.
9
1
RW
Selection of P2LED0 or GPIO10 on Pin 62
1 = This pin is used for P2LED0 (default).
0 = This pin is used for GPIO10.
8
1
RW
Selection of P1LED1 or GPIO7 on Pin 59
1 = This pin is used for P1LED1 (default).
0 = This pin is used for GPIO7.
7
1
RW
Reserved
6
1
RW
Reserved
5
1
RW
Reserved
4
1
RW
Reserved
3
1
RW
Reserved
2
1
RW
Reserved
1
1
RW
Reserved
0
1
RW
Reserved
4.2.15
4.2.15.1
CONFIGURATION STATUS AND SERIAL BUS MODE REGISTER
Configuration Status and Serial Bus Mode Register (0x0D8 – 0x0D9): CFGR
This register is used to select the Serial Bus and Fiber mode. The state of bits [1:0] are determined at reset time using
the RXD[1:0] pins.
TABLE 4-93:
CONFIGURATION STATUS AND SERIAL BUS MODE REGISTER (0X0D8 – 0X0D9):
CFGR
Bit
Default
R/W
Description
15 - 8
0x00
RO
Reserved
RW
Selection of Port 2 Mode of Operation
1 = Select copper mode
0 = Select fiber mode (bypass MLT3 encoder/decoder, scrambler and
descrambler). Valid for FML and FRL devices only.
When fiber mode is selected, bit[13] in DSP_CNTRL_6 (0x734 – 0x735)
should be cleared.
7
1
6
1
RW
Selection of Port 1 Mode of Operation
1 = Select copper mode
0 = Select fiber mode (bypass MLT3 encoder/decoder, scrambler and
descrambler). Valid for FML and FRL devices only.
When fiber mode is selected, bit[13] in DSP_CNTRL_6 (0x734 – 0x735)
should be cleared.
5-4
11
RO
Reserved
3-2
11
RW
Reserved
RW
Selection of Serial Bus Mode
00 = Reserved
01 = Reserved
10 = SPI slave Mode
11 = MIIM Mode
1-0
Strap-in value
from RXD[1:0]
2018 Microchip Technology Inc.
DS00002642A-page 133
KSZ8463ML/RL/FML/FRL
4.2.16
4.2.16.1
PORT 1 AUTO-NEGOTIATION REGISTERS
Port 1 Auto-Negotiation Next Page Transmit Register (0x0DC – 0x0DD): P1ANPT
This register contains the port 1 auto-negotiation next page transmit related bits.
TABLE 4-94:
Bit
PORT 1 AUTO-NEGOTIATION NEXT PAGE TRANSMIT REGISTER (0X0DC – 0X0DD):
P1ANPT
Default
R/W
Description
15
0
RO
Next Page
Next Page (NP) is used by the Next Page function to indicate whether or
not this is the last Next Page to be transmitted. NP shall be set as follows:
1 = Additional Next Page(s) will follow.
0 = Last page.
14
0
RO
Reserved
RO
Message Page
Message Page (MP) is used by the Next Page function to differentiate a
Message Page from an Unformatted Page. MP shall be set as follows:
1 = Message Page.
0 = Unformatted Page.
RO
Acknowledge 2
Acknowledge 2 (Ack2) is used by the Next Page function to indicate that
a device has the ability to comply with the message. Ack2 shall be set as
follows:
1 = Able to comply with message.
0 = Unable to comply with message.
13
1
12
0
11
0
RO
Toggle
Toggle (T) is used by the arbitration function to ensure synchronization
with the link partner during Next Page exchange. This bit shall always
take the opposite value of the Toggle bit in the previously exchanged Link
Codeword. The initial value of the Toggle bit in the first Next Page transmitted is the inverse of bit [11] in the base Link Codeword and, therefore,
may assume a value of logic one or zero. The Toggle bit shall be set as
follows:
1 = Previous value of the transmitted Link Codeword equal to logic zero.
0 = Previous value of the transmitted Link Codeword equal to logic one.
10 - 0
0x001
RO
Message and Unformatted Code Field
Message/Unformatted code field bit[10:0]
4.2.16.2
Port 1 Auto-Negotiation Link Partner Received Next Page Register (0x0DE – 0x0DF):
P1ALPRNP
This register contains the port 1 auto-negotiation link partner received next page related bits.
TABLE 4-95:
Bit
15
PORT 1 AUTO-NEGOTIATION LINK PARTNER RECEIVED NEXT PAGE REGISTER
(0X0DE – 0X0DF): P1ALPRNP
Default
0
DS00002642A-page 134
R/W
Description
RO
Next Page
Next Page (NP) is used by the Next Page function to indicate whether or
not this is the last Next Page to be transmitted. NP shall be set as follows:
1 = Additional Next Page(s) will follow.
0 = Last page.
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-95:
Bit
PORT 1 AUTO-NEGOTIATION LINK PARTNER RECEIVED NEXT PAGE REGISTER
(0X0DE – 0X0DF): P1ALPRNP (CONTINUED)
Default
14
0
13
0
12
0
R/W
Description
RO
Acknowledge
Acknowledge (Ack) is used by the auto-negotiation function to indicate
that a device has successfully received its Link Partner’s Link Codeword.
The Acknowledge bit is encoded in bit 14 regardless of the value of the
Selector Field or Link Codeword encoding. If no Next Page information is
to be sent, this bit shall be set to logic one in the Link Codeword after the
reception of at least three consecutive and consistent FLP Bursts (ignoring the Acknowledge bit value).
RO
Message Page
Message Page (MP) is used by the Next Page function to differentiate a
Message Page from an Unformatted Page. MP shall be set as follows:
1 = Message Page.
0 = Unformatted Page.
RO
Acknowledge 2
Acknowledge 2 (Ack2) is used by the Next Page function to indicate that
a device has the ability to comply with the message. Ack2 shall be set as
follows:
1 = Able to comply with message.
0 = Unable to comply with message.
11
0
RO
Toggle
Toggle (T) is used by the arbitration function to ensure synchronization
with the link partner during Next Page exchange. This bit shall always
take the opposite value of the Toggle bit in the previously exchanged Link
Codeword. The initial value of the Toggle bit in the first Next Page transmitted is the inverse of bit [11] in the base Link Codeword and, therefore,
may assume a value of logic one or zero. The Toggle bit shall be set as
follows:
1 = Previous value of the transmitted Link Codeword equal to logic zero.
0 = Previous value of the transmitted Link Codeword equal to logic one.
10 - 0
0x000
RO
Message and Unformatted Code Field
Message/Unformatted code field bit[10:0]
4.2.17
4.2.17.1
PORT 1 EEE REGISTERS
Port 1 EEE and Link Partner Advertisement Register (0x0E0 – 0x0E1): P1EEEA
This register contains the port 1 EEE advertisement and link partner advertisement information. Note that EEE is not
supported in fiber mode.
TABLE 4-96:
PORT 1 EEE AND LINK PARTNER ADVERTISEMENT REGISTER (0X0E0 – 0X0E1):
P1EEEA
Bit
Default
R/W
Description
15
0
RO
Reserved
14
0
RO
10GBASE-KR EEE
1 = Link Partner EEE is supported for 10GBASE-KR.
0 = Link Partner EEE is not supported for 10GBASE-KR.
13
0
RO
10GBASE-KX4 EEE
1 = Link Partner EEE is supported for 10GBASE-KX4.
0 = Link Partner EEE is not supported for 10GBASE-KX4.
12
0
RO
1000BASE-KX EEE
1 = Link Partner EEE is supported for 1000BASE-KX.
0 = Link Partner EEE is not supported for 1000BASE-KX.
2018 Microchip Technology Inc.
DS00002642A-page 135
KSZ8463ML/RL/FML/FRL
TABLE 4-96:
PORT 1 EEE AND LINK PARTNER ADVERTISEMENT REGISTER (0X0E0 – 0X0E1):
P1EEEA (CONTINUED)
Bit
Default
R/W
Description
11
0
RO
10GBASE-T EEE
1 = Link Partner EEE is supported for 10GBASE-T.
0 = Link Partner EEE is not supported for 10GBASE-T.
10
0
RO
1000BASE-T EEE
1 = Link Partner EEE is supported for 1000BASE-T.
0 = Link Partner EEE is not supported for 1000BASE-T.
9
0
RO
100BASE-TX EEE
1 = Link Partner EEE is supported for 100BASE-TX.
0 = Link Partner EEE is not supported for 100BASE-TX.
8-7
00
RO
Reserved
6
0
RO
10GBASE-KR EEE
1 = Port 1 EEE is supported for 10GBASE-KR.
0 = Port 1 EEE is not supported for 10GBASE-KR.
5
0
RO
10GBASE-KX4 EEE
1 = Port 1 EEE is supported for 10GBASE-KX4.
0 = Port 1 EEE is not supported for 10GBASE-KX4.
4
0
RO
1000BASE-KX EEE
1 = Port 1 EEE is supported for 1000BASE-KX.
0 = Port 1 EEE is not supported for 1000BASE-KX.
3
0
RO
10GBASE-T EEE
1 = Port 1 EEE is supported for 10GBASE-T.
0 = Port 1 EEE is not supported for 10GBASE-T.
2
0
RO
1000BASE-T EEE
1 = Port 1 EEE is supported for 1000BASE-T.
0 = Port 1 EEE is not supported for 1000BASE-T.
1
1
RW
100BASE-TX EEE
1 = Port 1 EEE is supported for 100BASE-TX.
0 = Port 1 EEE is not supported for 100BASE-TX.
To disable EEE capability, clear the port 1 Next Page Enable bit in the
PCSEEEC register (0x0F3).
0
0
RO
Reserved
4.2.17.2
Port 1 EEE Wake Error Count Register (0x0E2 – 0x0E3): P1EEEWEC
This register contains the port 1 EEE wake error count information. Note that EEE is not supported in Fiber mode.
TABLE 4-97:
Bit
15 - 0
PORT 1 EEE WAKE ERROR COUNT REGISTER (0X0E2 – 0X0E3): P1EEEWEC
Default
0x0000
DS00002642A-page 136
R/W
Description
RW
Port 1 EEE Wake Error Count
This counter is incremented by each transition of lpi_wake_timer_done
from FALSE to TRUE. It means the wakeup time is longer than 20.5 µs.
The value will be held at all ones in the case of overflow and will be
cleared to zero after this register is read.
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.17.3
Port 1 EEE Control/Status and Auto-Negotiation Expansion Register (0x0E4 – 0x0E5):
P1EEECS
This register contains the port 1 EEE control/status and auto-negotiation expansion information. Note that EEE is not
supported in Fiber mode.
TABLE 4-98:
PORT 1 EEE CONTROL/STATUS AND AUTO-NEGOTIATION EXPANSION REGISTER
(0X0E4 – 0X0E5): P1EEECS
Bit
Default
R/W
15
1
RW
Reserved
RO
Hardware 100BASE-TX EEE Enable Status
1 = 100BASE-TX EEE is enabled by hardware-based NP exchange.
0 = 100BASE-TX EEE is disabled.
14
13
12
11
0
0
0
0
Description
RO/LH
(Latching
High)
TX LPI Received
1 = Indicates that the transmit PCS has received low power idle (LPI) signaling one or more times since the register was last read.
0 = Indicates that the PCS has not received low power idle (LPI) signaling.
The status will be latched high and stay that way until cleared. To clear
this status bit, a “1” needs to be written to this register bit.
RO
TX LPI Indication
1 = Indicates that the transmit PCS is currently receiving low power idle
(LPI) signals.
0 = Indicates that the PCS is not currently receiving low power idle (LPI)
signals.
This bit will dynamically indicate the presence of the TX LPI signal.
RO/LH
(Latching
High)
RX LPI Received
1 = Indicates that the receive PCS has received low power idle (LPI) signaling one or more times since the register was last read.
0 = Indicates that the PCS has not received low power idle (LPI) signaling.
The status will be latched high and stay that way until cleared. To clear
this status bit, a “1” needs to be written to this register bit.
RX LPI Indication
1 = Indicates that the receive PCS is currently receiving low power idle
(LPI) signals.
0 = Indicates that the PCS is not currently receiving low power idle (LPI)
signals.
This bit will dynamically indicate the presence of the RX LPI signal.
10
0
RO
9-8
00
RW
Reserved
7
0
RO
Reserved
6
1
RO
Received Next Page Location Able
1 = Received Next Page storage location is specified by bit[6:5].
0 = Received Next Page storage location is not specified by bit[6:5].
1
RO
Received Next Page Storage Location
1 = Link partner Next Pages are stored in P1ALPRNP (Reg. 0x0DE –
0x0DF).
0 = Link partner Next Pages are stored in P1ANLPR (Reg. 0x056 –
0x057).
4
0
RO/LH
(Latching
High)
3
0
RO
5
2018 Microchip Technology Inc.
Parallel Detection Fault
1 = A fault has been detected via the parallel detection function.
0 = A fault has not been detected via the parallel detection function.
This bit is cleared after read.
Link Partner Next Page Able
1 = Link partner is Next Page abled.
0 = Link partner is not Next Page abled.
DS00002642A-page 137
KSZ8463ML/RL/FML/FRL
TABLE 4-98:
PORT 1 EEE CONTROL/STATUS AND AUTO-NEGOTIATION EXPANSION REGISTER
(0X0E4 – 0X0E5): P1EEECS (CONTINUED)
Bit
Default
R/W
Description
2
0
RO
Next Page Able
1 = Local device is Next Page abled.
0 = Local device is not Next Page abled.
1
0
RO/LH
(Latching
High)
Page Received
1 = A New Page has been received.
0 = A New Page has not been received.
0
0
RO
4.2.18
4.2.18.1
Link Partner Auto-Negotiation Able
1 = Link partner is auto-negotiation abled.
0 = Link partner is not auto-negotiation abled.
PORT 1 LPI RECOVERY TIME COUNTER REGISTER
Port 1 LPI Recovery Time Counter Register (0x0E6): P1LPIRTC
This register contains the port 1 LPI recovery time counter information.
TABLE 4-99:
Bit
7-0
4.2.19
4.2.19.1
PORT 1 LPI RECOVERY TIME COUNTER REGISTER (0X0E6): P1LPIRTC
Default
0x27 (25 µs)
R/W
Description
RW
Port 1 LPI Recovery Time Counter
This register specifies the time that the MAC device has to wait before it
can start to send out packets. This value should be the maximum of the
LPI recovery time between local device and remote device.
Each count is 640 ns.
BUFFER LOAD-TO-LPI CONTROL 1 REGISTER
Buffer Load to LPI Control 1 Register (0x0E7): BL2LPIC1
This register contains the buffer load to LPI Control 1 information.
TABLE 4-100: BUFFER LOAD TO LPI CONTROL 1 REGISTER (0X0E7): BL2LPIC1
Bit
Default
R/W
Description
7
0
RW
LPI Terminated by Input Traffic Enable
1 = LPI request will be stopped if input traffic is detected.
0 = LPI request won’t be stopped by input traffic.
6
0
RO
Reserved
RW
Buffer Load Threshold for Source Port LPI Termination
This value defines the maximum buffer usage allowed for a single port
before it starts to trigger the LPI termination for the specific source port.
(512 bytes per unit)
5-0
0x08
DS00002642A-page 138
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.20
4.2.20.1
PORT 2 AUTO-NEGOTIATION REGISTERS
Port 2 Auto-Negotiation Next Page Transmit Register (0x0E8 – 0x0E9): P2ANPT
This register contains the port 2 auto-negotiation next page transmit related bits.
TABLE 4-101: PORT 2 AUTO-NEGOTIATION NEXT PAGE TRANSMIT REGISTER (0X0E8 – 0X0E9):
P2ANPT
Bit
Default
R/W
Description
15
0
RO
Next Page
Next Page (NP) is used by the Next Page function to indicate whether or
not this is the last Next Page to be transmitted. NP shall be set as follows:
1 = Additional Next Page(s) will follow.
0 = Last page.
14
0
RO
Reserved
RO
Message Page
Message Page (MP) is used by the Next Page function to differentiate a
Message Page from an Unformatted Page. MP shall be set as follows:
1 = Message Page.
0 = Unformatted Page.
RO
Acknowledge 2
Acknowledge 2 (Ack2) is used by the Next Page function to indicate that
a device has the ability to comply with the message. Ack2 shall be set as
follows:
1 = Able to comply with message.
0 = Unable to comply with message.
13
12
1
0
11
0
RO
Toggle
Toggle (T) is used by the arbitration function to ensure synchronization
with the link partner during Next Page exchange. This bit shall always
take the opposite value of the Toggle bit in the previously exchanged Link
Codeword. The initial value of the Toggle bit in the first Next Page transmitted is the inverse of bit[11] in the base Link Codeword and, therefore,
may assume a value of logic one or zero. The Toggle bit shall be set as
follows:
1 = Previous value of the transmitted Link Codeword equal to logic zero.
0 = Previous value of the transmitted Link Codeword equal to logic one.
10 - 0
0x001
RO
Message and Unformatted Code Field
Message/Unformatted code field bit[10:0]
4.2.20.2
Port 2 Auto-Negotiation Link Partner Received Next Page Register (0x0EA – 0x0EB):
P2ALPRNP
This register contains the port 2 auto-negotiation link partner received next page related bits.
TABLE 4-102: PORT 2 AUTO-NEGOTIATION LINK PARTNER RECEIVED NEXT PAGE REGISTER
(0X0EA – 0X0EB): P2ALPRNP
Bit
15
Default
0
2018 Microchip Technology Inc.
R/W
Description
RO
Next Page
Next Page (NP) is used by the Next Page function to indicate whether or
not this is the last Next Page to be transmitted. NP shall be set as follows:
1 = Additional Next Page(s) will follow.
0 = Last page.
DS00002642A-page 139
KSZ8463ML/RL/FML/FRL
TABLE 4-102: PORT 2 AUTO-NEGOTIATION LINK PARTNER RECEIVED NEXT PAGE REGISTER
(0X0EA – 0X0EB): P2ALPRNP (CONTINUED)
Bit
14
13
12
Default
0
0
0
R/W
Description
RO
Acknowledge
Acknowledge (Ack) is used by the auto-negotiation function to indicate
that a device has successfully received its Link Partner’s Link Codeword.
The Acknowledge bit is encoded in bit [14] regardless of the value of the
Selector Field or Link Codeword encoding. If no Next Page information is
to be sent, this bit shall be set to logic one in the Link Codeword after the
reception of at least three consecutive and consistent FLP Bursts (ignoring the Acknowledge bit value).
RO
Message Page
Message Page (MP) is used by the Next Page function to differentiate a
Message Page from an Unformatted Page. MP shall be set as follows:
1 = Message Page.
0 = Unformatted Page.
RO
Acknowledge 2
Acknowledge 2 (Ack2) is used by the Next Page function to indicate that
a device has the ability to comply with the message. Ack2 shall be set as
follows:
1 = Able to comply with message.
0 = Unable to comply with message.
11
0
RO
Toggle
Toggle (T) is used by the arbitration function to ensure synchronization
with the link partner during Next Page exchange. This bit shall always
take the opposite value of the Toggle bit in the previously exchanged Link
Codeword. The initial value of the Toggle bit in the first Next Page transmitted is the inverse of bit[11] in the base Link Codeword and, therefore,
may assume a value of logic one or zero. The Toggle bit shall be set as
follows:
1 = Previous value of the transmitted Link Codeword equal to logic zero.
0 = Previous value of the transmitted Link Codeword equal to logic one.
10 - 0
0x000
RO
Message and Unformatted Code Field
Message/Unformatted code field bit[10:0]
4.2.21
4.2.21.1
PORT 2 EEE REGISTERS
Port 2 EEE and Link Partner Advertisement Register (0x0EC – 0x0ED): P2EEEA
This register contains the port 2 EEE advertisement and link partner advertisement information. Note that EEE is not
supported in Fiber mode. Note that EEE is not supported in Fiber mode.
TABLE 4-103: PORT 2 EEE AND LINK PARTNER ADVERTISEMENT REGISTER (0X0EC – 0X0ED):
P2EEEA
Bit
Default
R/W
Description
15
0
RO
Reserved
14
0
RO
10GBASE-KR EEE
1 = Link Partner EEE is supported for 10GBASE-KR.
0 = Link Partner EEE is not supported for 10GBASE-KR.
13
0
RO
10GBASE-KX4 EEE
1 = Link Partner EEE is supported for 10GBASE-KX4.
0 = Link Partner EEE is not supported for 10GBASE-KX4.
12
0
RO
1000BASE-KX EEE
1 = Link Partner EEE is supported for 1000BASE-KX.
0 = Link Partner EEE is not supported for 1000BASE-KX.
DS00002642A-page 140
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-103: PORT 2 EEE AND LINK PARTNER ADVERTISEMENT REGISTER (0X0EC – 0X0ED):
P2EEEA (CONTINUED)
Bit
Default
R/W
Description
11
0
RO
10GBASE-T EEE
1 = Link Partner EEE is supported for 10GBASE-T.
0 = Link Partner EEE is not supported for 10GBASE-T.
10
0
RO
1000BASE-T EEE
1 = Link Partner EEE is supported for 1000BASE-T.
0 = Link Partner EEE is not supported for 1000BASE-T.
9
0
RO
100BASE-TX EEE
1 = Link Partner EEE is supported for 100BASE-TX.
0 = Link Partner EEE is not supported for 100BASE-TX.
8-7
00
RO
Reserved
6
0
RO
10GBASE-KR EEE
1 = Port 2 EEE is supported for 10GBASE-KR.
0 = Port 2 EEE is not supported for 10GBASE-KR.
5
0
RO
10GBASE-KX4 EEE
1 = Port 2 EEE is supported for 10GBASE-KX4.
0 = Port 2 EEE is not supported for 10GBASE-KX4.
4
0
RO
1000BASE-KX EEE
1 = Port 2 EEE is supported for 1000BASE-KX.
0 = Port 2 EEE is not supported for 1000BASE-KX.
3
0
RO
10GBASE-T EEE
1 = Port 2 EEE is supported for 10GBASE-T.
0 = Port 2 EEE is not supported for 10GBASE-T.
2
0
RO
1000BASE-T EEE
1 = Port 2 EEE is supported for 1000BASE-T.
0 = Port 2 EEE is not supported for 1000BASE-T.
1
1
RW
100BASE-TX EEE
1 = Port 2 EEE is supported for 100BASE-TX.
0 = Port 2 EEE is not supported for 100BASE-TX.
To disable EEE capability, clear the port 2 Next Page Enable bit in the
PCSEEEC register (0x0F3).
0
0
RO
Reserved
4.2.21.2
Port 2 EEE Wake Error Count Register (0x0EE – 0x0EF): P2EEEWEC
This register contains the port 2 EEE wake error count information. Note that EEE is not supported in Fiber mode.
TABLE 4-104: PORT 2 EEE WAKE ERROR COUNT REGISTER (0X0EE – 0X0EF): P2EEEWEC
Bit
15 - 0
Default
0x0000
2018 Microchip Technology Inc.
R/W
Description
RW
Port 2 EEE Wake Error Count
This counter is incremented by each transition of lpi_wake_timer_done
from FALSE to TRUE. It means the wake-up time is longer than 20.5 µs.
The value will be held at all ones in the case of overflow and will be
cleared to zero after this register is read.
DS00002642A-page 141
KSZ8463ML/RL/FML/FRL
4.2.21.3
Port 2 EEE Control/Status and Auto-Negotiation Expansion Register (0x0F0 – 0x0F1):
P2EEECS
This register contains the port 2 EEE control/status and auto-negotiation expansion information. Note that EEE is not
supported in Fiber mode.
TABLE 4-105: PORT 2 EEE CONTROL/STATUS AND AUTO-NEGOTIATION EXPANSION REGISTER
(0X0F0 – 0X0F1): P2EEECS
Bit
Default
R/W
15
1
RW
Reserved
RO
Hardware 100BASE-TX EEE Enable Status
1 = 100BASE-TX EEE is enabled by hardware based NP exchange.
0 = 100BASE-TX EEE is disabled.
14
13
12
11
0
0
0
0
Description
RO/LH
(Latching
High)
TX LPI Received
1 = Indicates that the transmit PCS has received low power idle (LPI) signaling one or more times since the register was last read.
0 = Indicates that the PCS has not received low power idle (LPI) signaling.
The status will be latched high and stay that way until cleared. To clear
this status bit, a “1” needs to be written to this register bit.
RO
TX LPI Indication
1 = Indicates that the transmit PCS is currently receiving low power idle
(LPI) signals.
0 = Indicates that the PCS is not currently receiving low power idle (LPI)
signals.
This bit will dynamically indicate the presence of the TX LPI signal.
RO/LH
(Latching
High)
RX LPI Received
1 = Indicates that the receive PCS has received low power idle (LPI) signaling one or more times since the register was last read.
0 = Indicates that the PCS has not received low power idle (LPI) signaling.
The status will be latched high and stay that way until cleared. To clear
this status bit, a “1” needs to be written to this register bit.
RX LPI Indication
1 = Indicates that the receive PCS is currently receiving low power idle
(LPI) signals.
0 = Indicates that the PCS is not currently receiving low power idle (LPI)
signals.
This bit will dynamically indicate the presence of the RX LPI signal.
10
0
RO
9-8
00
RW
Reserved
7
0
RO
Reserved
6
1
RO
Received Next Page Location Able
1 = Received Next Page storage location is specified by bit[6:5].
0 = Received Next Page storage location is not specified by bit[6:5].
1
RO
Received Next Page Storage Location
1 = Link partner Next Pages are stored in P2ALPRNP (Reg. 0x0EA –
0x0EB).
0 = Link partner Next Pages are stored in P2ANLPR (Reg. 0x062 –
0x063).
4
0
RO/LH
(Latching
High)
3
0
RO
5
DS00002642A-page 142
Parallel Detection Fault
1 = A fault has been detected via the parallel detection function.
0 = A fault has not been detected via the parallel detection function.
This bit is cleared after read.
Link Partner Next Page Able
1 = Link partner is Next Page abled.
0 = Link partner is not Next Page abled.
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-105: PORT 2 EEE CONTROL/STATUS AND AUTO-NEGOTIATION EXPANSION REGISTER
(0X0F0 – 0X0F1): P2EEECS (CONTINUED)
Bit
Default
R/W
Description
2
1
RO
Next Page Able
1 = Local device is Next Page abled.
0 = Local device is not Next Page abled.
1
0
RO/LH
(Latching
High)
Page Received
1 = A New Page has been received.
0 = A New Page has not been received.
0
0
RO
4.2.22
4.2.22.1
Link Partner Auto-Negotiation Able
1 = Link partner is auto-negotiation abled.
0 = Link partner is not auto-negotiation abled.
PORT 2 LPI RECOVERY TIME COUNTER REGISTER
Port 2 LPI Recovery Time Counter Register (0x0F2): P2LPIRTC
This register contains the port 2 LPI recovery time counter information.
TABLE 4-106: PORT 2 LPI RECOVERY TIME COUNTER REGISTER (0X0F2): P2LPIRTC
Bit
7-0
4.2.23
4.2.23.1
Default
0x27 (25 µs)
R/W
Description
RW
Port 2 LPI Recovery Time Counter
This register specifies the time that the MAC device has to wait before it
can start to send out packets. This value should be the maximum of the
LPI recovery time between local device and remote device.
Each count is 640 ns.
PCS EEE CONTROL REGISTER
PCS EEE Control Register (0x0F3): PCSEEEC
This register contains the PCS EEE control information.
TABLE 4-107: PCS EEE CONTROL REGISTER (0X0F3): PCSEEEC
Bit
Default
R/W
Description
7
0
RW
Reserved
6
0
RW
Reserved
5-2
0x0
RO
Reserved
RW
Port 2 Next Page Enable
1 = Enable next page exchange during auto-negotiation.
0 = Skip next page exchange during auto-negotiation.
Auto-negotiation uses next page to negotiate EEE. To disable EEE autonegotiation on port 2, clear this bit to zero. Restarting auto-negotiation
may then be required.
RW
Port 1 Next Page Enable
1 = Enable next page exchange during auto-negotiation.
0 = Skip next page exchange during auto-negotiation.
Auto-negotiation uses next page to negotiate EEE. To disable EEE autonegotiation on port 1, clear this bit to zero. Restarting auto-negotiation
may then be required.
1
0
1
1
2018 Microchip Technology Inc.
DS00002642A-page 143
KSZ8463ML/RL/FML/FRL
4.2.24
4.2.24.1
EMPTY TXQ-TO-LPI WAIT TIME CONTROL REGISTER
Empty TXQ to LPI Wait Time Control Register (0x0F4 – 0x0F5): ETLWTC
This register contains the empty TXQ to LPI wait time control information.
TABLE 4-108: EMPTY TXQ TO LPI WAIT TIME CONTROL REGISTER (0X0F4 – 0X0F5): ETLWTC
Bit
15 - 0
4.2.25
4.2.25.1
Default
0x03E8
R/W
Description
RW
Empty TXQ to LPI Wait Time Control
This register specifies the time that the LPI request will be generated
after a TXQ has been empty exceeds this configured time. This is only
valid when EEE 100BASE-TX is enabled. This setting will apply to all the
three ports. The unit is 1.3 ms. The default value is 1.3 seconds (range
from 1.3 ms to 86 seconds)
BUFFER LOAD-TO-LPI CONTROL 2 REGISTER
Buffer Load to LPI Control 2 Register (0x0F6 – 0x0F7): BL2LPIC2
This register contains the buffer load to LPI control 2 information.
TABLE 4-109: BUFFER LOAD TO LPI CONTROL 2 REGISTER (0X0F6 – 0X0F7): BL2LPIC2
Bit
Default
R/W
15 - 8
0x01
RO
Reserved
RW
Buffer Load Threshold for All Ports LPI Termination
This value defines the maximum buffer usage allowed for a single port
before it starts to trigger the LPI termination for every port. (128 bytes per
unit)
7-0
4.2.25.2
4.2.26
0x40
Description
0x0F8 – 0x0FF: Reserved
INTERNAL I/O REGISTER SPACE MAPPING FOR INTERRUPTS AND GLOBAL RESET
(0X100 – 0X1FF)
4.2.26.1
0x100 – 0x123: Reserved
4.2.26.2
Memory BIST Info Register (0x124 – 0x125): MBIR
This register indicates the built-in self-test results for both TX and RX memories after power-up/reset. The device should
be reset after the BIST procedure to ensure proper subsequent operation.
TABLE 4-110: MEMORY BIST INFO REGISTER (0X124 – 0X125): MBIR
Bit
Default
R/W
Description
15
0
RO
Memory BIST Done
0 = BIST In progress
1 = BIST Done
14 - 13
00
RO
Reserved
12
—
RO
TXMBF TX Memory BIST Completed
0 = TX Memory built-in self-test has not completed.
1 = TX Memory built-in self-test has completed.
11
—
RO
TXMBFA TX Memory BIST Failed
0 = TX Memory built-in self-test has completed without failure.
1 = TX Memory built-in self-test has completed with failure.
10 - 8
—
RO
TXMBFC TX Memory BIST Fail Count
0 = TX Memory built-in self-test completed with no count failure.
1 = TX Memory built-in self-test encountered a failed count condition.
7-5
—
RO
Reserved
DS00002642A-page 144
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-110: MEMORY BIST INFO REGISTER (0X124 – 0X125): MBIR (CONTINUED)
Bit
Default
R/W
Description
4
—
RO
RXMBF RX Memory BIST Completed
0 = Completion has not occurred for the RX Memory built-in self-test.
1 = Indicates completion of the RX Memory built-in self-test.
3
—
RO
RXMBFA RX Memory BIST Failed
0 = No failure with the RX Memory built-in self-test.
1 = Indicates the RX Memory built-in self-test has failed.
2-0
—
RO
RXMBFC RX Memory BIST Test Fail Count
0 = No count failure for the RX Memory BIST.
1 = Indicates the RX Memory built−in self-test failed count.
4.2.26.3
Global Reset Register (0x126 – 0x127): GRR
This register controls the global and PTP reset functions with information programmed by the CPU.
TABLE 4-111: GLOBAL RESET REGISTER (0X126 – 0X127): GRR
Bit
Default
R/W
Description
15 - 4
0x000
RO
Reserved
3
0
RW
Memory BIST Start
1 = Setting this bit will start the Memory BIST.
0 = Setting this bit will stop the Memory BIST.
2
0
RW
PTP Module Soft Reset
1 = Setting this bit resets the 1588/PTP blocks including the time stamp
input units, the trigger output units and the PTP clock.
0 = Software reset is inactive.
1
0
RO
Reserved
RW
Global Soft Reset
1 = Software reset is active.
0 = Software reset is inactive.
Global software reset will reset all registers to their default value. The
strap−in values are not affected. This bit is not self-clearing. After writing
a “1” to this bit, wait for 10 ms to elapse then write a “0” for normal operation.
0
0
4.2.26.4
0x128 – 0x18F: Reserved
4.2.26.5
Interrupt Enable Register (0x190 – 0x191): IER
This register either enables various interrupts or indicates that the interrupts have been enabled.
TABLE 4-112: INTERRUPT ENABLE REGISTER (0X190 – 0X191): IER
Bit
Default
R/W
Description
15
0
RW
LCIE Link Change Interrupt Enable
1 = When this bit is set, the link change interrupt is enabled.
0 = When this bit is reset, the link change interrupt is disabled.
14 - 13
00
RO
Reserved
RO
PTP Time stamp Interrupt Enable
1 = When set, this bit indicates that the PTP time stamp interrupt is
enabled.
0 = When cleared, this bit indicates that the PTP time stamp interrupt is
disabled.
Note that this bit is an “OR” of the PTP_TS_IE[11:0] bits. Clearing the
appropriate enable bit in the PTP_TS_IE register (0x68E – 0x68F) or
clearing the appropriate status bit in the PTP_TS_IS register (0x68C –
0x68D) will clear this bit. Always write this bit as a zero.
12
0
2018 Microchip Technology Inc.
DS00002642A-page 145
KSZ8463ML/RL/FML/FRL
TABLE 4-112: INTERRUPT ENABLE REGISTER (0X190 – 0X191): IER (CONTINUED)
Bit
Default
R/W
Description
11
0
RO
Reserved
10
0
RO
PTP Trigger Unit Interrupt Enable
1 = When set, this bit indicates that the PTP trigger output unit interrupt is
enabled.
0 = When cleared, this bit indicates that the PTP trigger output unit interrupt is disabled.
Note that this bit is an “OR” of the PTP_TRIG_IE[11:0] bits. Clearing the
appropriate enable bit in the PTP_TRIG_IE register (0x68A – 0x68B) or
clearing the appropriate status bit in the PTP_TRIG_IS register (0x688 –
0x689) will clear this bit. Always write this bit as a zero.
9-4
0x00
RO
Reserved
RW
LDIE Linkup Detect Interrupt Enable
1 = When this bit is set, the wake-up from a link up detect interrupt is
enabled.
0 = When this bit is reset, the link up detect interrupt is disabled.
3
0
2
0
RW
EDIE Energy Detect Interrupt Enable
1 = When this bit is set, the wake-up from energy detect interrupt is
enabled.
0 = When this bit is reset, the energy detect interrupt is disabled.
1
0
RO
Reserved
0
0
RO
Reserved
4.2.26.6
Interrupt Status Register (0x192 – 0x193): ISR
This register contains the status bits for all interrupt sources. When the corresponding enable bit is set, it causes the
interrupt pin to be asserted. This register is usually read by the host CPU and device drivers during an interrupt service
routine or polling. The register bits are not cleared when read. To clear the bits, the user has to either write a “1” to a
specific bit to clear it, or write a “1” to another bit in another specified register to clear it.
TABLE 4-113: INTERRUPT STATUS REGISTER (0X192 – 0X193): ISR
Bit
Default
15
0
14 - 13
00
R/W
Description
LCIS Link Change Interrupt Status
When this bit is set, it indicates that the link status has changed from link
RO (W1C)
up to link down, or link down to link up.
This edge-triggered interrupt status is cleared by writing a “1” to this bit.
RO
Reserved
12
0
RO
PTP Time stamp Interrupt Status
When this bit is set, it indicates that one of 12 time stamp input units is
ready (TS_RDY = “1”) and an event has been captured, or the egress
time stamp is available from either port 1 or port 2.
This edge-triggered interrupt status is cleared by writing a “1” to this bit.
11
0
RO
Reserved
PTP Trigger Unit Interrupt Status
When this bit is set, it indicates that one of 12 trigger output units is done
or has an error.
This edge-triggered interrupt status is cleared by writing a “1” to this bit.
10
0
RO
9-4
0x00
RO
Reserved
RO
LDIS Linkup Detect Interrupt Status
When this bit is set, it indicates that wake-up from linkup detect status
has occurred. Write 0010 to PMCTRL[5:2] to clear this bit.
3
0
DS00002642A-page 146
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-113: INTERRUPT STATUS REGISTER (0X192 – 0X193): ISR (CONTINUED)
Bit
Default
R/W
Description
2
0
RO
EDIS Energy Detect Interrupt Status
When this bit is set, it indicates that wake-up from energy detect status
has occurred.
Write 0001 to PMCTRL[5:2] to clear this bit.
1-0
00
RO
Reserved
4.2.26.7
4.2.27
4.2.27.1
0x194 – 0x1FF: Reserved
INTERNAL I/O REGISTER SPACE MAPPING FOR TRIGGER OUTPUT UNITS (12 UNITS,
0X200 – 0X3FF)
Trigger Error Register (0x200 – 0x201): TRIG_ERR
This register contains the trigger output unit error status.
TABLE 4-114: TRIGGER ERROR REGISTER (0X200 – 0X201): TRIG_ERR
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
RO
Trigger Output Unit Error
1 = The trigger time is set earlier than the system time clock when
TRIG_NOTIFY bit is set to “1” in TRIG_CFG1 register and it will generate
interrupt to host if interrupt enable bit is set in PTP_TRIG_IE register.
This bit can be cleared by resetting the TRIG_EN bit to “0”.
0 = No trigger output unit error.
There are 12 trigger output units and therefore there is a corresponding
Error bit for each of the trigger output units, bit[11:0] = unit[12:1].
11 - 0
4.2.27.2
0x000
Trigger Active Register (0x202 – 0x203): TRIG_ACTIVE
This register contains the trigger output unit active status.
TABLE 4-115: TRIGGER ACTIVE REGISTER (0X202 – 0X203): TRIG_ACTIVE
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
RO
Trigger Output Unit Active
1 = The trigger output unit is enabled and active without error.
0 = The trigger output unit is finished and inactive.
There are 12 trigger output units and therefore there is a corresponding
active bit for each of the trigger output units, bit[11:0] = unit[12:1].
11 - 0
4.2.27.3
0x000
Trigger Done Register (0x204 – 0x205): TRIG_DONE
This register contains the trigger output unit event done status.
TABLE 4-116: TRIGGER DONE REGISTER (0X204 – 0X205): TRIG_DONE
Bit
Default
R/W
15 - 12
0x0
RO
11 - 0
0x000
2018 Microchip Technology Inc.
RO
(W1C)
Description
Reserved
Trigger Output Unit Event Done
1 = The trigger output unit event has been generated when TRIG_NOTIFY bit is set to “1” in TRIG_CFG1 register (write “1” to clear this bit) and
it will generate interrupt to host if interrupt enable bit is set in
PTP_TRIG_IE register.
0 = The trigger output unit event is not generated.
There are 12 trigger output units and therefore there is a corresponding
Done bit for each of the trigger output units, bit[11:0] = unit[12:1].
DS00002642A-page 147
KSZ8463ML/RL/FML/FRL
4.2.27.4
Trigger Enable Register (0x206 – 0x207): TRIG_EN
This register contains the trigger output unit enable control bits.
TABLE 4-117: TRIGGER ENABLE REGISTER (0X206 – 0X207): TRIG_EN
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
RW
Trigger Output Unit Enable
1 = Enables the selected trigger output unit and will self-clear when the
trigger output is generated. In cascade mode, only enable the head of
trigger unit.
0 = The trigger output unit is disabled.
There are 12 trigger output units and therefore there is a corresponding
enable bit for each of the trigger output units, bit[11:0] = unit[12:1].
11 - 0
4.2.27.5
0x000
Trigger Software Reset Register (0x208 – 0x209): TRIG_SW_RST
This register contains the software reset bits for the trigger output units.
TABLE 4-118: TRIGGER SOFTWARE RESET REGISTER (0X208 – 0X209): TRIG_SW_RST
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
11 - 0
4.2.27.6
0x000
RW/SC
Trigger Output Unit Software Reset
1 = When set, the selected trigger output unit is put into the inactive state
and default setting. This can be used to stop the cascade mode in continuous operation and prepare the selected trigger unit for the next operation.
0 = While zero, the selected trigger output unit is in normal operating
mode.
There are 12 trigger output units and therefore there is a corresponding
software reset bit for each of the trigger output units, bit[11:0] = unit[12:1].
Trigger Output Unit 12 Output PPS Pulse-Width Register (0x20A – 0x20B):
TRIG12_PPS_WIDTH
This register contains the trigger output unit 12 PPS pulse width and trigger output unit 1 path delay compensation.
TABLE 4-119: TRIGGER OUTPUT UNIT 12 OUTPUT PPS PULSE-WIDTH REGISTER (0X20A –
0X20B): TRIG12_PPS_WIDTH
Bit
Default
15 - 12
0x0
RO
Reserved
11
0
RW
Reserved
RW
Path Delay Compensation for Trigger Output Unit 1
These three bits are used to compensate the path delay of clock skew for
event trigger output unit 1 in the range of 0 ns ~ 7 ns (bit[11] = “1”) or 0 ns
~ 28 ns (bit[11] = “0”).
RW
PPS Pulse Width for Trigger Output Unit 12
This is upper third byte [23:16] in conjunction with the unit 12 trigger output pulse width in TRIG12_CFG_2[15:0] (0x38A) register to make this
register value for PPS pulse width up to 134 ms.
10 - 8
7-0
4.2.27.7
000
0x00
R/W
Description
0x20C – 0x21F: Reserved
DS00002642A-page 148
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.27.8
Trigger Output Unit 1 Target Time in Nanoseconds Low-Word Register (0x220 – 0x221):
TRIG1_TGT_NSL
This register contains the trigger output unit 1 target time in nanoseconds low-word.
TABLE 4-120: TRIGGER OUTPUT UNIT 1 TARGET TIME IN NANOSECONDS LOW-WORD
REGISTER (0X220 – 0X221): TRIG1_TGT_NSL
Bit
Default
R/W
Description
15 - 0
0x0000
RW
Trigger Output Unit 1Target Time in Nanoseconds Low-Word [15:0]
This is low-word of target time for trigger output unit 1 in nanoseconds.
4.2.27.9
Trigger Output Unit 1 Target Time in Nanoseconds High-Word Register (0x222 – 0x223):
TRIG1_TGT_NSH
This register contains the trigger output unit 1 target time in nanoseconds high-word.
TABLE 4-121: TRIGGER OUTPUT UNIT 1 TARGET TIME IN NANOSECONDS HIGH-WORD
REGISTER (0X222 – 0X223): TRIG1_TGT_NSH
Bit
Default
R/W
Description
15 - 14
00
RO
Reserved
13 - 0
0x0000
RW
Trigger Output Unit 1Target Time in Nanoseconds High-Word
[29:16]
This is high-word of target time for trigger output unit 1 in nanoseconds.
4.2.27.10
Trigger Output Unit 1 Target Time in Seconds Low-Word Register (0x224 – 0x225):
TRIG1_TGT_SL
This register contains the trigger output unit 1 target time in seconds low-word.
TABLE 4-122: TRIGGER OUTPUT UNIT 1 TARGET TIME IN SECONDS LOW-WORD REGISTER
(0X224 – 0X225): TRIG1_TGT_SL
Bit
Default
R/W
Description
15 - 0
0x0000
RW
Trigger Output Unit 1Target Time in Seconds Low-Word [15:0]
This is low-word of target time for trigger output unit 1 in seconds.
4.2.27.11
Trigger Output Unit 1 Target Time in Seconds High-Word Register (0x226 – 0x227):
TRIG1_TGT_SH
This register contains the trigger output unit 1 target time in seconds high-word.
TABLE 4-123: TRIGGER OUTPUT UNIT 1 TARGET TIME IN SECONDS HIGH-WORD REGISTER
(0X226 – 0X227): TRIG1_TGT_SH
Bit
Default
R/W
Description
15 - 0
0x0000
RW
Trigger Output Unit 1 Target Time in Seconds High-Word [31:16]
This is high-word of target time for trigger output unit 1 in seconds.
4.2.27.12
Trigger Output Unit 1 Configuration and Control Register 1 (0x228 – 0x229): TRIG1_CFG_1
This register (1 of 8) contains the trigger output unit 1 configuration and control bits.
TABLE 4-124: TRIGGER OUTPUT UNIT 1 CONFIGURATION AND CONTROL REGISTER 1 (0X228 –
0X229): TRIG1_CFG_1
Bit
Default
R/W
Description
15
0
RW
Enable This Trigger Output Unit in Cascade Mode
1 = Enable this trigger output unit in cascade mode.
0 = disable this trigger output unit in cascade mode.
2018 Microchip Technology Inc.
DS00002642A-page 149
KSZ8463ML/RL/FML/FRL
TABLE 4-124: TRIGGER OUTPUT UNIT 1 CONFIGURATION AND CONTROL REGISTER 1 (0X228 –
0X229): TRIG1_CFG_1 (CONTINUED)
Bit
14
13 - 10
9
Default
0
0xF
0
R/W
Description
RW
Indicate a Tail Unit for This Trigger Output Unit in Cascade Mode
1 = This trigger output unit is the last unit of the chain in cascade mode.
0 = This trigger output unit is not the last unit of a chain in cascade mode.
Note: When this bit is set “0” in all CFG_1 trigger units, and all units are
in cascade mode, the iteration count is ignored and it becomes infinite.
To stop the infinite loop, set the respective bit[11:0] in TRIG_SW_RST
register.
RW
Select Upstream Trigger Unit in Cascade Mode
These bits are used to select one of the 12 upstream trigger output units
in Cascade mode.
Note: 0x0 indicates TOU1, and 0xB indicates TOU12. (0xC to 0xF are
not used.) For example, if units 1, 2 and 3 (tail unit) are set up in cascade
mode, then these 4 bits are set as follows at the three trigger output units:
unit 1 is set to 0x2 (indicates TOU3), at unit 2 is set to 0x0 (indicates
TOU1) and at unit 3 is to set 0x1 (indicates TOU2).
RW
Trigger Now
1 = Immediately create the trigger output if the trigger target time is less
than the system time clock.
0 = Wait for the trigger target time to occur to trigger the event output.
8
0
RW
Trigger Notify
1 = Enable reporting both TRIG_DONE and TRIG_ERR status as well as
interrupt to host if the interrupt enable bit is set in the TRIG_IE register.
0 = Disable reporting both TRIG_DONE and TRIG_ERR status.
7
0
RO
Reserved
RW
Trigger Output Signal Pattern
This field is used to select the trigger output signal pattern when
TRIG_EN = “1” and trigger target time has reached the system time:
000: TRIG_NEG_EDGE - Generates negative edge (from default “H” ->
“L” and stays “L”).
001: TRIG_POS_EDGE - Generates positive edge (from default “L” ->
“H” and stays “H”).
010: TRIG_NEG_PULSE - Generates negative pulse (from default “H” ->
“L” pulse -> “H” and stays “H”). The pulse width is defined in TRIG1_CFG_2 register.
011: TRIG_POS_PULSE - Generates positive pulse (from default “L” ->
“H” pulse -> “L” and stays “L”). The pulse width is defined in TRIG1_CFG_2 register.
100: TRIG_NEG_CYCLE - Generates negative periodic signal. The “L”
pulse width is defined in TRIG1_CFG_2 register, the cycle width is
defined in TRIG1_CFG_3/4 registers and the number of cycles is defined
in TRIG1_CFG_5 register (it is an infinite number if this register value is
zero).
101: TRIG_POS_CYCLE - Generates positive periodic signal. The “H”
pulse width is defined in TRIG1_CFG_2 register, the cycle width is
defined in TRIG1_CFG_3/4 registers and the number of cycles is defined
in TRIG1_CFG_5 register (it is an infinite number if this register value is
zero).
110: TRIG_REG_OUTPUT - Generates an output signal from a 16-bit
register. This 16-bit register bit-pattern in TRIG1_CFG_6 is shifted LSB
bit first and looped, each bit width is defined in TRIG1_CFG_3/4 registers
and total number of bits to shift out is defined in TRIG1_CFG_5 register
(it is an infinite number if this register value is zero).
111: Reserved
Note: the maximum output clock frequency is up to 12.5 MHz.
6-4
000
DS00002642A-page 150
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-124: TRIGGER OUTPUT UNIT 1 CONFIGURATION AND CONTROL REGISTER 1 (0X228 –
0X229): TRIG1_CFG_1 (CONTINUED)
Bit
3-0
4.2.27.13
Default
0x0
R/W
Description
RW
Select GPIO[11:0] for This Trigger Output Unit
Associate one of the 12 GPIO pins to this trigger output unit. The trigger
output signals are OR’ed together to form a combined signal if multiple
trigger output units have selected the same GPIO output pin.
0x0 indicates GPIO0, and 0xB indicates GPIO11. (0xC to 0xF are not
used.)
Trigger Output Unit 1 Configuration and Control Register 2 (0x22A – 0x22B): TRIG1_CFG_2
This register (2 of 8) contains the trigger output unit 1 configuration and control bits.
TABLE 4-125: TRIGGER OUTPUT UNIT 1 CONFIGURATION AND CONTROL REGISTER 2 (0X22A –
0X22B): TRIG1_CFG_2
Bit
15 - 0
4.2.27.14
Default
0x0000
R/W
Description
RW
Trigger Output Pulse Width
This number defines the width of the generated pulse or periodic signal
from this trigger output unit. Its unit value is equal to 8 ns. For example,
the pulse width is 80 ns if this register value is 10 (0xA).
Iteration Count
This number defines the iteration count for register trigger output pattern
(TRIG1_CFG_6) in cascade mode when this trigger output unit is the tail
unit. For example, 0x0000 = 1 count and 0x000F = 16 counts. It is an
infinite number if there is no tail unit in Cascade mode.
Trigger Output Unit 1 Configuration and Control Register 3 (0x22C – 0x22D): TRIG1_CFG_3
This register (3 of 8) contains the trigger output Unit 1 configuration and control bits.
TABLE 4-126: TRIGGER OUTPUT UNIT 1 CONFIGURATION AND CONTROL REGISTER 3 (0X22C –
0X22D): TRIG1_CFG_3
Bit
15 - 0
4.2.27.15
Default
0x0000
R/W
Description
RW
Trigger Output Cycle Width or Bit Width Low-Word [15:0]
To define cycle width for generating periodic signal or to define each bit
width in TRIG1_CFG_8. A unit number of value equals to 1 ns. For
example, the cycle or bit width is 80 ns if this register value is 80 (0x50)
and next register value = 0x0000.
Trigger Output Unit 1 Configuration and Control Register 4 (0x22E – 0x22F): TRIG1_CFG_4
This register (4 of 8) contains the trigger output unit 1 configuration and control bits.
TABLE 4-127: TRIGGER OUTPUT UNIT 1 CONFIGURATION AND CONTROL REGISTER 4 (0X22E –
0X22F): TRIG1_CFG_4
Bit
15 - 0
Default
0x0000
2018 Microchip Technology Inc.
R/W
Description
RW
Trigger Output Cycle Width or Bit Width High-Word [31:16]
This number defines the cycle width when generating periodic signals
using this trigger output unit. Also, it is used to define each bit width in
TRIG1_CFG_8. Each unit is equal to 1 ns.
DS00002642A-page 151
KSZ8463ML/RL/FML/FRL
4.2.27.16
Trigger Output Unit 1 Configuration and Control Register 5 (0x230 – 0x231): TRIG1_CFG_5
This register (5 of 8) contains the trigger output unit 1 configuration and control bits.
TABLE 4-128: TRIGGER OUTPUT UNIT 1 CONFIGURATION AND CONTROL REGISTER 5 (0X230 –
0X231): TRIG1_CFG_5
Bit
15 - 0
4.2.27.17
Default
0x0000
R/W
Description
RW
Trigger Output Cycle Count
This number defines the quantity of cycles of the periodic signal output
by the trigger output unit. Use a value of zero for infinite repetition. Valid
for TRIG_NEG_CYCLE and TRIG_POS_CYCLE modes.
Bit Count
This number can define the number of bits that are output when generating output signals from the bit pattern register. It is an infinite number if
this register value is zero. Valid for TRIG_REG_OUTPUT mode.
Trigger Output Unit 1 Configuration and Control Register 6 (0x232 – 0x233): TRIG1_CFG_6
This register (6 of 8) contains the trigger output unit 1 configuration and control bits.
TABLE 4-129: TRIGGER OUTPUT UNIT 1 CONFIGURATION AND CONTROL REGISTER 6 (0X232 –
0X233): TRIG1_CFG_6
Bit
15 - 0
4.2.27.18
Default
0x0000
R/W
Description
RW
Trigger Output Unit Bit Pattern
This register is used to define the output bit pattern when the
TRIG_REG_OUTPUT mode is selected.
Iteration Count
This register is used as the iteration count for the trigger output unit when
the tail unit is in cascade mode but not using register mode. It is the number of cycles programmed in CFG_5 to be output by the trigger output
unit. For example, 0x0000 = 1 count, 0x000F = 16 counts. An infinite
number of cycles will occur if there is no tail unit in Cascade mode.
Trigger Output Unit 1 Configuration and Control Register 7 (0x234 – 0x235): TRIG1_CFG_7
This register (7 of 8) contains the trigger output unit 1 configuration and control bits.
TABLE 4-130: TRIGGER OUTPUT UNIT 1 CONFIGURATION AND CONTROL REGISTER 7 (0X234 –
0X235): TRIG1_CFG_7
Bit
15 - 0
Default
0x0000
DS00002642A-page 152
R/W
Description
RW
Trigger Output Iteration Cycle Time in Cascade Mode Low-Word
[15:0]
The value in this pair of registers defines the iteration cycle time for the
trigger output unit in cascade mode. This value will be added to the current trigger target time for establishing the next trigger time for the trigger
output unit. A unit number of value equals to 1 ns. For example, the cycle
is 800 ns if this register value is 800 (0x320) and next register value =
0x0000. The iteration count (CFG_6) × trigger output cycle count
(CFG_5) x waveform cycle time must be less than the iteration cycle time
specified in CFG_7 and CFG_8.
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.27.19
Trigger Output Unit 1 Configuration and Control Register 8 (0x236 – 0x237): TRIG1_CFG_8
This register (8 of 8) contains the trigger output unit 1 configuration and control bits.
TABLE 4-131: TRIGGER OUTPUT UNIT 1 CONFIGURATION AND CONTROL REGISTER 8 (0X236 –
0X237): TRIG1_CFG_8
Bit
15 - 0
Default
0x0000
R/W
Description
RW
Trigger Output Iteration Cycle Time in Cascade Mode High-Word
[31:16]
The value in this pair of registers defines the iteration cycle time for the
trigger output unit in cascade mode. This value will be added to the current trigger target time for establishing the next trigger time for the trigger
output unit. A unit number of value equals 1 ns.
4.2.27.20
0x238 – 0x23F: Reserved
4.2.27.21
Trigger Output Unit 2 Target Time and Output Configuration/Control Registers (0x240 –
0x257)
These 12 registers contain the trigger output unit 2 target time and configuration/control bits, TRIG2_CFG_[1:8]. See
descriptions in Section 4.2.27.8 through Section 4.2.27.19. Note that there is one bit that is different in this set of register
bits. It is indicated in the following text.
4.2.27.22
Trigger Output Unit 2 Configuration and Control Register 1 (0x248 – 0x249): TRIG2_CFG_1
This register contains the trigger output unit 2 configuration and control bits.
TABLE 4-132: TRIGGER OUTPUT UNIT 2 CONFIGURATION AND CONTROL REGISTER 1 (0X248 –
0X249): TRIG2_CFG_1
Bit
7
Default
0
R/W
Description
RW
Trigger Unit 2 Clock Edge Output Select
This bit is used to select either the positive edge or negative edge of the
125 MHz to clock out the trigger unit 2 output. This bit only pertains to
usage with GPIO1 pin. This bit will not function with any other GPIO pin.
1 = Use negative edge of 125 MHz clock to clock out data
0 = Use positive edge of 125 MHz clock to clock out data
4.2.27.23
0x258 – 0x25F: Reserved
4.2.27.24
Trigger Output Unit 3 Target Time and Output Configuration/Control Registers (0x260 –
0x277)
These 12 registers contain the trigger output unit 3 target time and configuration/control bits, TRIG3_CFG_[1:8]. See
descriptions in Section 4.2.27.8 through Section 4.2.27.19.
4.2.27.25
0x278 – 0x27F: Reserved
4.2.27.26
Trigger Output Unit 4 Target Time and Output Configuration/Control Registers (0x280 –
0x297)
These 12 registers contain the trigger output unit 4 target time and configuration/control bits, TRIG4_CFG_[1:8]. See
descriptions in Section 4.2.27.8 through Section 4.2.27.19.
4.2.27.27
0x298 – 0x29F: Reserved
4.2.27.28
Trigger Output Unit 5 Target Time and Output Configuration/Control Registers (0x2A0 –
0x2B7)
These 12 registers contain the trigger output unit 5 target time and configuration/control bits, TRIG5_CFG_[1:8]. See
descriptions in Section 4.2.27.8 through Section 4.2.27.19.
2018 Microchip Technology Inc.
DS00002642A-page 153
KSZ8463ML/RL/FML/FRL
4.2.27.29
0x2B8 – 0x2BF: Reserved
4.2.27.30
Trigger Output Unit 6 Target Time and Output Configuration/Control Registers (0x2C0 –
0x2D7)
These 12 registers contain the trigger output unit 6 target time and configuration/control bits, TRIG6_CFG_[1:8]. See
descriptions in Section 4.2.27.8 through Section 4.2.27.19.
4.2.27.31
0x2D8 – 0x2DF: Reserved
4.2.27.32
Trigger Output Unit 7 Target Time and Output Configuration/Control Registers (0x2E0 –
0x2F7)
These 12 registers contain the trigger output unit 7 target time and configuration/control bits, TRIG7_CFG_[1:8]. See
descriptions in Section 4.2.27.8 through Section 4.2.27.19.
4.2.27.33
0x2F8 – 0x2FF: Reserved
4.2.27.34
Trigger Output Unit 8 Target Time and Output Configuration/Control Registers (0x300 –
0x317)
These 12 registers contain the trigger output unit 8 target time and configuration/control bits, TRIG8_CFG_[1:8]. See
descriptions in Section 4.2.27.8 through Section 4.2.27.19.
4.2.27.35
0x318 – 0x31F: Reserved
4.2.27.36
Trigger Output Unit 9 Target Time and Output Configuration/Control Registers (0x320 –
0x337)
These 12 registers contain the trigger output unit 9 target time and configuration/control bits, TRIG9_CFG_[1:8]. See
descriptions in Section 4.2.27.8 through Section 4.2.27.19.
4.2.27.37
0x338 – 0x33F: Reserved
4.2.27.38
Trigger Output Unit 10 Target Time and Output Configuration/Control Registers (0x340 –
0x357)
These 12 registers contain the trigger output unit 10 target time and configuration/control bits, TRIG10_CFG_[1:8]. See
descriptions in Section 4.2.27.8 through Section 4.2.27.19.
4.2.27.39
0x358 – 0x35F: Reserved
4.2.27.40
Trigger Output Unit 11 Target Time and Output Configuration/Control Registers (0x360 –
0x377)
These 12 registers contain the trigger output unit 11 target time and configuration/control bits, TRIG11_CFG_[1:8]. See
descriptions in Section 4.2.27.8 through Section 4.2.27.19.
4.2.27.41
0x378 – 0x37F: Reserved
4.2.27.42
Trigger Output Unit 12 Target Time and Output Configuration/Control Registers (0x380 –
0x397)
These 12 registers contain the trigger output unit 12 target time and configuration/control bits, TRIG12_CFG_[1:8]. See
descriptions in Section 4.2.27.8 through Section 4.2.27.19.
4.2.27.43
0x398 – 0x3FF: Reserved
DS00002642A-page 154
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.28
4.2.28.1
INTERNAL I/O REGISTER SPACE MAPPING FOR PTP TIME STAMP INPUTS (12 UNITS,
0X400 – 0X5FF)
Time Stamp Ready Register (0x400 – 0x401): TS_RDY
This register contains the PTP time stamp input unit ready-to-read status bits.
TABLE 4-133: TIME STAMP READY REGISTER (0X400 – 0X401): TS_RDY
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
RO
Time Stamp Input Unit Ready
1 = This time stamp input unit is ready to read and will generate a time
stamp interrupt if PTP_TS_IE = “1”. This bit will clear when TS_EN is disabled.
0 = This time stamp input unit is not ready to read or disabled.
There are 12 time stamp units and therefore there is a corresponding
time stamp input ready bit for each of the time stamp units, bit[11:0] =
unit[12:1].
11 - 0
4.2.28.2
0x000
Time Stamp Enable Register (0x402 – 0x403): TS_EN
This register contains the PTP time stamp input unit enable control bits.
TABLE 4-134: TIME STAMP ENABLE REGISTER (0X402 – 0X403): TS_EN
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
RO
Time Stamp Input Unit Enable
1 = Enable the selected time stamp input unit. Writing a ”1” to this bit will
clear the TS[12:1]_EVENT_DET_CNT.
0 = Disable the selected time stamp input unit. Writing a “0” to this bit will
clear the TS_RDY and TS[12:1]_DET_CNT_OVFL.
There are 12 time stamp units and therefore there is a corresponding
time stamp input unit enable bit for each of the time stamp units, bit[11:0]
= unit[12:1].
11 - 0
4.2.28.3
0x000
Time Stamp Software Reset Register (0x404 – 0x405): TS_SW_RST
This register contains the PTP time stamp input unit software reset control bits.
TABLE 4-135: TIME STAMP SOFTWARE RESET REGISTER (0X404 – 0X405): TS_SW_RST
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
11 - 0
4.2.28.4
0x000
RW/SC
Time Stamp Input Unit Software Reset
1 = Reset the selected time stamp input unit to inactive state and default
setting.
0 = The selected time stamp input unit is in normal mode of operation.
There are 12 time stamp units and therefore there is a corresponding
time stamp input unit software reset bit for each of the time stamp units,
bit[11:0] = unit[12:1].
0x406 – 0x41F: Reserved
2018 Microchip Technology Inc.
DS00002642A-page 155
KSZ8463ML/RL/FML/FRL
4.2.28.5
Time Stamp Unit 1 Status Register (0x420 – 0x421): TS1_STATUS
This register contains PTP time stamp input unit 1 status.
TABLE 4-136: TIME STAMP UNIT 1 STATUS REGISTER (0X420 – 0X421): TS1_STATUS
Bit
Default
R/W
Description
15 - 4
0x000
RO
Reserved
RO
Number of Detected Event Count for Time stamp Input Unit 1
(TS1_EVENT_DET_CNT)
This field is used to report the number of detected events (either rising or
falling edge) count. in single mode, it can detect up to 15 events in any
single time stamp input unit. In cascade mode, it can detect up to two
events in time stamp input units 1-11 or up to 8 events at time stamp input
unit 12 as a non-tail unit, and it can detect up to 15 events for any time
stamp input unit as a tail unit. Pulses or edges can be detected up to
25 MHz. The pulse width can be measured by the difference between
consecutive time stamps in the same time stamp input unit.
RO
Number of Detected Event Count Overflow for Time stamp Input
Unit 1 (TS1_DET_CNT_OVFL)
1 = The number of detected event (either rising or falling edge) count has
overflowed. In cascade mode, only tail unit will set this bit when overflow
is occurred. The TS1_EVENT_DET_CNT will stay at 15 when overflow is
occurred.
0 = The number of events (either rising or falling edge) detected count
has not overflowed.
4-1
0
4.2.28.6
0x0
0
Time Stamp Unit 1 Configuration and Control Register (0x422 – 0x423): TS1_CFG
This register contains PTP time stamp input unit 1 configuration and control bits.
TABLE 4-137: TIME STAMP UNIT 1 CONFIGURATION AND CONTROL REGISTER (0X422 – 0X423):
TS1_CFG
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
11 - 8
0x0
RW
Select GPIO[11:0] for Time stamp Unit 1
This field is used to select one of the 12 GPIO pins to serve this time
stamp unit. It is GPIO0 if these bits = “0000” and it is GPIO11 if these bits
= “1011” (from “1100” to “1111” are not used).
7
0
RW
Enable Rising Edge Detection
1 = Enable rising edge detection.
0 = Disable rising edge detection.
6
0
RW
Enable Falling Edge Detection
1 = Enable falling edge detection.
0 = Disable falling edge detection.
5
0
RW
Select Tail Unit for this Time stamp Unit in Cascade Mode
1 = This time stamp unit is the last unit of the chain in cascade mode.
0 = This time stamp unit is not the last unit of the chain in cascade mode.
4-1
0x0
RW
Select Upstream Time stamp Done Unit in Cascade Mode
This is used to select one of the 12 upstream time stamps units for done
input in cascade mode. For example, if units 1 (head unit), 2 and 3 (tail
unit) are set up in cascade mode, then these 4-bits at unit 1 are set to
0x0, at unit 2 are set to 0x1, at unit 3 are set to 0x2.
0
0
RW
Enable This Time stamp Unit in Cascade Mode
1 = Enable the selected time stamp input unit in Cascade mode.
0 = Disable the time stamp input unit in Cascade mode.
DS00002642A-page 156
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.28.7
Time Stamp Unit 1 Input 1st Sample Time in Nanoseconds Low-Word Register (0x424 –
0x425): TS1_SMPL1_NSL
This register contains the first sample time in nanoseconds low-word (the resolution of 40 ns) for PTP time stamp unit 1.
TABLE 4-138: TIME STAMP UNIT 1 INPUT 1ST SAMPLE TIME IN NANOSECONDS LOW-WORD
REGISTER (0X424 – 0X425): TS1_SMPL1_NSL
Bit
Default
R/W
Description
15 - 0
0x0000
RO
1st Sample Time in ns Low-Word [15:0] Time stamp Unit 1
This is the low-word of first sample time for time stamp unit 1 in nanoseconds.
4.2.28.8
Time Stamp Unit 1 Input 1st Sample Time in Nanoseconds High-Word Register (0x426 –
0x427): TS1_SMPL1_NSH
This register contains the first sample time in nanoseconds high-word and edge detection status for PTP time stamp
unit 1.
TABLE 4-139: TIME STAMP UNIT 1 INPUT 1ST SAMPLE TIME IN NANOSECONDS HIGH-WORD
REGISTER (0X426 – 0X427): TS1_SMPL1_NSH
Bit
Default
R/W
Description
15
0
RO
Reserved
14
0
RO
1st Sample Edge Indication for Time stamp Unit 1
0 = Indicates the event is a falling edge signal.
1 = Indicates the event is a rising edge signal.
13 - 0
0x0000
RO
1st Sample Time in ns High-Word [29:16] for Time stamp Unit 1
This is the high-word of first sample time for time stamp unit 1 in nanoseconds.
4.2.28.9
Time Stamp Unit 1 Input 1st Sample Time in Seconds Low-Word Register (0x428 – 0x429):
TS1_SMPL1_SL
This register contains the first sample time in seconds low-word for PTP time stamp unit 1.
TABLE 4-140: TIME STAMP UNIT 1 INPUT 1ST SAMPLE TIME IN SECONDS LOW-WORD
REGISTER (0X428 – 0X429): TS1_SMPL1_SL
Bit
Default
R/W
Description
15 - 0
0x0000
RO
1st Sample Time in Seconds Low-Word [15:0] for Time stamp Unit 1
This is the low-word of first sample time for time stamp unit 1 in seconds.
4.2.28.10
Time Stamp Unit 1 Input 1st Sample Time in Seconds High-Word Register (0x42A – 0x42B):
TS1_SMPL1_SH
This register contains the first sample time in seconds high-word for PTP time stamp unit 1.
TABLE 4-141: TIME STAMP UNIT 1 INPUT 1ST SAMPLE TIME IN SECONDS HIGH-WORD
REGISTER (0X42A – 0X42B): TS1_SMPL1_SH
Bit
Default
R/W
Description
15 - 0
0x0000
RO
1st Sample Time in Seconds High-Word [31:16] for Time Stamp Unit
1
This is the high-word of first sample time for time stamp unit 1 in seconds.
2018 Microchip Technology Inc.
DS00002642A-page 157
KSZ8463ML/RL/FML/FRL
4.2.28.11
Time Stamp Unit 1 Input 1st Sample Time in Sub-Nanoseconds Register (0x42C – 0x42D):
TS1_SMPL1_SUB_NS
This register contains the first sample time in sub-8 nanoseconds (the resolution of 8 ns) for PTP time stamp unit 1.
TABLE 4-142: TIME STAMP UNIT 1 INPUT 1ST SAMPLE TIME IN SUB-NANOSECONDS REGISTER
(0X42C – 0X42D): TS1_SMPL1_SUB_NS
Bit
Default
R/W
Description
15 - 3
0x0000
RO
Reserved
RO
1st Sample Time in Sub-8 Nanoseconds for Time stamp Unit 1
These bits indicate one of the 8 ns cycles for the first sample time for time
stamp unit 1.
000: 0 ns (sample time at the first 8 ns cycle in 25 MHz/40 ns)
001: 8 ns (sample time at the second 8 ns cycle in 25 MHz/40 ns)
010: 16 ns (sample time at the third 8 ns cycle in 25 MHz/40 ns)
011: 24 ns (sample time at the fourth 8 ns cycle in 25 MHz/40 ns)
100: 32 ns (sample time at the fifth 8 ns cycle in 25 MHz/40 ns)
101-111: NA
2-0
000
4.2.28.12
0x42E – 0x433: Reserved
4.2.28.13
Time Stamp Unit 1 Input 2nd Sample Time in Nanoseconds Low-Word Register (0x434 –
0x435): TS1_SMPL2_NSL
This register contains the second sample time in nanoseconds low-word (the resolution of 40 ns) for PTP time stamp
Unit 1.
TABLE 4-143: TIME STAMP UNIT 1 INPUT 2ND SAMPLE TIME IN NANOSECONDS LOW-WORD
REGISTER (0X434 – 0X435): TS1_SMPL2_NSL
Bit
15 - 0
4.2.28.14
Default
0x0000
R/W
Description
RO
2nd Sample Time in Nanoseconds for Low-Word [15:0] for Time
stamp Unit 1
This is the low-word of the 2nd sample time for time stamp unit 1 in nanoseconds.
Time stamp Unit 1 Input 2nd Sample Time in Nanoseconds High-Word Register (0x436 –
0x437): TS1_SMPL2_NSH
This register contains the 2nd sample time in nanoseconds high-word and edge detection status for the PTP time stamp
unit 1.
TABLE 4-144: TIME STAMP UNIT 1 INPUT 2ND SAMPLE TIME IN NANOSECONDS HIGH-WORD
REGISTER (0X436 – 0X437): TS1_SMPL2_NSH
Bit
Default
R/W
Description
15
0
RO
Reserved
14
0
RO
2nd Sample Edge Indication for Time stamp Unit 1
0 = Indicates the event is a falling edge signal.
1 = Indicates the event is a rising edge signal.
RO
2nd Sample Time in Nanoseconds High-Word [29:16] for Time
stamp Unit 1
This is the high-word of the 2nd sample time for time stamp unit 1 in
nanoseconds.
13 - 0
0x0000
DS00002642A-page 158
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.28.15
Time Stamp Unit 1 Input 2nd Sample Time in Seconds Low-Word Register (0x438 – 0x439):
TS1_SMPL2_SL
This register contains the 2nd sample time in seconds low-word for PTP time stamp unit 1.
TABLE 4-145: TIME STAMP UNIT 1 INPUT 2ND SAMPLE TIME IN SECONDS LOW-WORD
REGISTER (0X438 – 0X439): TS1_SMPL2_SL
Bit
Default
R/W
Description
15 - 0
0x0000
RO
2nd Sample Time in Seconds Low-Word [15:0] for Time stamp Unit 1
This is the low-word of the second sample time for time stamp unit 1 in
seconds.
4.2.28.16
Time Stamp Unit 1 Input 2nd Sample Time in Seconds High-Word Register (0x43A – 0x43B):
TS1_SMPL2_SH
This register contains the 2nd sample time in seconds high-word for PTP time stamp unit 1.
TABLE 4-146: TIME STAMP UNIT 1 INPUT 2ND SAMPLE TIME IN SECONDS HIGH-WORD
REGISTER (0X43A – 0X43B): TS1_SMPL2_SH
Bit
15 - 0
4.2.28.17
Default
0x0000
R/W
Description
RO
2nd Sample Time in Seconds High-Word [31:16] for Time stamp Unit
1
This is the high-word of the second sample time for time stamp unit 1 in
seconds.
Time Stamp Unit 1 Input 2nd Sample Time in Sub-Nanoseconds Register (0x43C – 0x43D):
TS1_SMPL2_SUB_NS
This register contains the 2nd sample time in sub-8 nanoseconds (the resolution of 8 ns) for PTP time stamp unit 1.
TABLE 4-147: TIME STAMP UNIT 1 INPUT 2ND SAMPLE TIME IN SUB-NANOSECONDS REGISTER
(0X43C – 0X43D): TS1_SMPL2_SUB_NS
Bit
Default
R/W
Description
15 - 3
0x0000
RO
Reserved
RO
2nd Sample Time in Sub-8 Nanoseconds for Time stamp Unit 1
These bits indicate one of the 8 ns cycle for the second sample time for
time stamp unit 1.
000: 0 ns (sample time at the first 8 ns cycle in 25 MHz/40 ns)
001: 8 ns (sample time at the second 8 ns cycle in 25 MHz/40 ns)
010: 16 ns (sample time at the third 8 ns cycle in 25 MHz/40 ns)
011: 24 ns (sample time at the fourth 8 ns cycle in 25 MHz/40 ns)
100: 32 ns (sample time at the fifth 8 ns cycle in 25 MHz/40 ns)
101-111: NA
2-0
000
4.2.28.18
0x43E – 0x43F: Reserved
4.2.28.19
Time Stamp Unit 2 Status/Configuration/Control and Input 1st Sample Time Registers (0x440
– 0x44D)
These seven registers contain the first sample time and status/configuration/control information for PTP time stamp unit
2. See description in time stamp unit 1 (0x420 – 0x42D).
4.2.28.20
0x44E – 0x453: Reserved
4.2.28.21
Time Stamp Unit 2 Input 2nd Sample Time Registers (0x454 – 0x45D)
These five registers contain the second sample time for PTP time stamp unit 2. See description in time stamp unit 1
(0x434 – 0x43D).
2018 Microchip Technology Inc.
DS00002642A-page 159
KSZ8463ML/RL/FML/FRL
4.2.28.22
0x45E – 0x45F: Reserved
4.2.28.23
Time Stamp Unit 3 Status/Configuration/Control and Input 1st Sample Time Registers (0x460
– 0x46D)
These seven registers contain the first sample time and status/configuration/control information for PTP time stamp unit
3. See description in time stamp unit 1 (0x420 – 0x42D).
4.2.28.24
0x46E – 0x473: Reserved
4.2.28.25
Time Stamp Unit 3 Input 2nd Sample Time Registers (0x474 – 0x47D)
These five registers contain the 2nd sample time for PTP time stamp unit 3. See description in time stamp unit 1 (0x434
– 0x43D).
4.2.28.26
0x47E – 0x47F: Reserved
4.2.28.27
Time Stamp Unit 4 Status/Configuration/Control and Input 1st Sample Time Registers (0x480
– 0x48D)
These seven registers contain the1st sample time and status/configuration/control information for PTP time stamp unit
4. See description in time stamp unit 1 (0x420 – 0x42D).
4.2.28.28
0x48E – 0x493: Reserved
4.2.28.29
Time Stamp Unit 4 Input 2nd Sample Time Registers (0x494 – 0x49D)
These five registers contain the 2nd sample time for PTP time stamp unit 4 input. See description in time stamp unit 1
(0x434 – 0x43D).
4.2.28.30
0x49E – 0x49F: Reserved
4.2.28.31
Time Stamp Unit 5 Status/Configuration/Control and Input 1st Sample Time Registers (0x4A0
– 0x4AD)
These seven registers contain the 1st sample time and status/configuration/control information for PTP time stamp unit
5. See description in time stamp unit 1 (0x420 – 0x42D).
4.2.28.32
0x4AE – 0x4B3: Reserved
4.2.28.33
Time Stamp Unit 5 Input 2nd Sample Time Registers (0x4B4 – 0x4BD)
These five registers contain the 2nd sample time for PTP time stamp unit 5. See description in time stamp unit 1 (0x434
– 0x43D).
4.2.28.34
0x4BE – 0x4BF: Reserved
4.2.28.35
Time Stamp Unit 6 Status/Configuration/Control and Input 1st Sample Time Registers (0x4C0
– 0x4CD)
These seven registers contain the 1st sample time and status/configuration/control information for PTP time stamp unit
6. See description in time stamp unit 1 (0x420 – 0x42D).
4.2.28.36
0x4CE – 0x4D3: Reserved
4.2.28.37
Time Stamp Unit 6 Input 2nd Sample Time Registers (0x4D4 – 0x4DD)
These five registers contain the 2nd sample time for PTP time stamp unit 6. See description in time stamp unit 1 (0x434
– 0x43D).
DS00002642A-page 160
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.28.38
0x4DE – 0x4DF: Reserved
4.2.28.39
Time Stamp Unit 7 Status/Configuration/Control and Input 1st Sample Time Registers (0x4E0
– 0x4ED)
These seven registers contain the 1st sample time and status/configuration/control information for PTP time stamp unit
7. See description in time stamp unit 1 (0x420 – 0x42D).
4.2.28.40
0x4EE – 0x4F3: Reserved
4.2.28.41
Time Stamp Unit 7 Input 2nd Sample Time Registers (0x4F4 – 0x4FD)
These five registers contain the 2nd sample time for PTP time stamp unit 7. See description in time stamp unit 1 (0x434
– 0x43D).
4.2.28.42
0x4FE – 0x4FF: Reserved
4.2.28.43
Time Stamp Unit 8 Status/Configuration/Control and Input 1st Sample Time Registers (0x500
– 0x50D)
These seven registers contain the1st sample time and status/configuration/control information for PTP time stamp unit
8. See description in time stamp unit 1 (0x420 – 0x42D).
4.2.28.44
0x50E – 0x513: Reserved
4.2.28.45
Time Stamp Unit 8 Input 2nd Sample Time Registers (0x514 – 0x51D)
These five registers contain the 2nd sample time for PTP time stamp unit 8. See description in time stamp unit 1 (0x434
– 0x43D).
4.2.28.46
0x51E – 0x51F: Reserved
4.2.28.47
Time Stamp Unit 9 Status/Configuration/Control and Input 1st Sample Time Registers (0x520
– 0x52D)
These seven registers contain the 1st sample time and status/configuration/control information for PTP time stamp unit
9. See description in time stamp unit 1 (0x420 – 0x42D).
4.2.28.48
0x52E – 0x533: Reserved
4.2.28.49
Time Stamp Unit 9 Input 2nd Sample Time Registers (0x534 – 0x53D)
These five registers contain the 2nd sample time for PTP time stamp unit 9. See description in time stamp unit 1 (0x434
– 0x43D).
4.2.28.50
0x53E – 0x53F: Reserved
4.2.28.51
Time Stamp Unit 10 Status/Configuration/Control and Input 1st Sample Time Registers (0x540
– 0x54D)
These seven registers contain the 1st sample time and status/configuration/control information for PTP time stamp unit
10. See description in time stamp unit 1 (0x420 – 0x42D).
4.2.28.52
0x54E – 0x553: Reserved
4.2.28.53
Time Stamp Unit 10 Input 2nd Sample Time Registers (0x554 – 0x55D)
These five registers contain the 2nd sample time for PTP time stamp unit 10. See description in time stamp unit 1 (0x434
– 0x43D).
2018 Microchip Technology Inc.
DS00002642A-page 161
KSZ8463ML/RL/FML/FRL
4.2.28.54
0x55E – 0x55F: Reserved
4.2.28.55
Time Stamp Unit 11 Status/Configuration/Control and Input 1st Sample Time Registers (0x560
– 0x56D)
These seven registers contain the1st sample time and status/configuration/control information for PTP time stamp unit
11. See description in time stamp unit 1 (0x420 – 0x42D).
4.2.28.56
0x56E – 0x573: Reserved
4.2.28.57
Time Stamp Unit 11 Input 2nd Sample Time Registers (0x574 – 0x57D)
These five registers contain the 2nd sample time for PTP time stamp unit 11. See description in time stamp unit 1 (0x434
– 0x43D).
4.2.28.58
0x57E – 0x57F: Reserved
4.2.28.59
Time Stamp Unit 12 Status/Configuration/Control and Input 1st Sample Time Registers (0x580
– 0x58D)
(Note: Time stamp unit 12 has eight sample time registers available)
These seven registers contain the 1st sample time and status/configuration/control information for PTP time stamp unit
12. See description in time stamp unit 1 (0x420 – 0x42D).
4.2.28.60
0x58E – 0x593: Reserved
4.2.28.61
Time Stamp Unit 12 Input 2nd Sample Time Registers (0x594 – 0x59D)
These 5 registers contain the 2nd sample time for PTP time stamp unit 12. See description in time stamp unit 1 (0x434
– 0x43D).
4.2.28.62
0x59E – 0x5A3: Reserved
4.2.28.63
Time Stamp Unit 12 Input 3rd Sample Time Registers (0x5A4 – 0x5AD)
These 5 registers contain the 3rd sample time for PTP time stamp unit 12. See description in time stamp unit 1 (0x434
– 0x43D).
4.2.28.64
0x5AE – 0x5B3: Reserved
4.2.28.65
Time Stamp Unit 12 Input 4th Sample Time Registers (0x5B4 – 0x5BD)
These five registers contain the 4th sample time for PTP time stamp unit 12. See description in time stamp unit 1 (0x434
– 0x43D).
4.2.28.66
0x5BE – 0x5C3: Reserved
4.2.28.67
Time Stamp Unit 12 Input 5th Sample Time Registers (0x5C4 – 0x5CD)
These five registers contain the 5th sample time for PTP time stamp unit 12. See description in time stamp unit 1 (0x434
– 0x43D).
4.2.28.68
0x5CE – 0x5D3: Reserved
4.2.28.69
Time Stamp Unit 12 Input 6th Sample Time Registers (0x5D4 – 0x5DD)
These five registers contain the 6th sample time for PTP time stamp unit 12. See description in time stamp unit 1 (0x434
– 0x43D).
4.2.28.70
0x5DE – 0x5E3: Reserved
4.2.28.71
Time Stamp Unit 12 Input 7th Sample Time Registers (0x5E4 – 0x5ED)
These five registers contain the 7th sample time for PTP time stamp unit 12. See description in time stamp unit 1 (0x434
– 0x43D).
DS00002642A-page 162
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.28.72
0x5EE – 0x5F3: Reserved
4.2.28.73
Time stamp Unit 12 Input 8th Sample Time Registers (0x5F4 – 0x5FD)
These five registers contain the 8th sample time for PTP time stamp unit 12. See description in time stamp unit 1 (0x434
– 0x43D).
4.2.28.74
4.2.29
4.2.29.1
0x5FE – 0x5FF: Reserved
INTERNAL I/O REGISTERS SPACE MAPPING FOR PTP 1588 CLOCK AND GLOBAL
CONTROL (0X600 – 0X7FF)
PTP Clock Control Register (0x600 – 0x601): PTP_CLK_CTL
This register contains control of PTP 1588 clock.
TABLE 4-148: PTP CLOCK CONTROL REGISTER (0X600 – 0X601): PTP_CLK_CTL
Bit
Default
R/W
Description
15 - 7
0x000
RO
Reserved
6
5
4
3
2
0
0
0
0
0
RW/SC
Enable Step Adjustment Mode to PTP 1588 Clock
(PTP_STEP_ADJ_CLK)
Setting this bit will cause the time value in PTP_RTC_NSH/L registers to
be added (PTP_STEP_DIR, bit [5]= “1” or subtracted (PTP_STEP_DIR,
bit [5] = “0”) from the system time clock. This bit is self-clearing.
RW
Direction Control for Step Adjustment Mode
(PTP_STEP_DIR)
1 = To add the time value in PTP_RTC_NSH/L registers to system time
clock.
0 = To subtract the time value in PTP_RTC_NSH/L registers from system
time clock.
RW/SC
Enable Read PTP 1588 Clock
(PTP_READ_CLK)
Setting this bit will cause the device to sample the PTP 1588 clock time
value. This time value will be made available for reading through the
PTP_RTC_SH/L, PTP_RTC_NSH/L and PTP_RTC_PHASE registers.
This bit is self-clearing.
RW/SC
Enable Load PTP 1588 Clock for Direct Time Setting Mode
(PTP_LOAD_CLK)
Setting this bit will cause the device to load the PTP 1588 clock time
value from PTP_RTC_SH/L, PTP_RTC_NSH/L and PTP_RTC_PHASE
registers. The writes to PTP_RTC_SH/L, PTP_RTC_NSH/L and
PTP_RTC_PHASE are performed before setting this bit. This bit is selfclearing.
RW
Enable Continuous Adjustment Mode for PTP 1588 Clock
(PTP_CONTINU_ADJ_CLK)
1 = Enable continuous incrementing (PTP_RATE_DIR = “0”) or decrementing (PTP_RATE_DIR = “1”) frequency adjustment by the value in
PTP_SNS_RATE_H [29:16] and PTP_SNS_RATE_L [15:0] on every
25 MHz clock cycle.
0 = Disable continuous adjustment mode to PTP 1588 clock.
Enable PTP 1588 Clock
(EN_PTP_CLK)
1 = To enable the PTP clock.
0 = To disable the PTP clock and the PTP clock will be frozen. For nonPTP mode, this bit is set to “0” for stopping clock toggling.
1
1
RW
0
0
RW/SC
2018 Microchip Technology Inc.
Reset PTP 1588 Clock
(RESET_PTP _CLK)
Setting this bit will reset the PTP 1588 clock.
DS00002642A-page 163
KSZ8463ML/RL/FML/FRL
4.2.29.2
0x602 – 0x603: Reserved
4.2.29.3
PTP Real Time Clock in Nanoseconds Low-Word Register (0x604 – 0x605): PTP_RTC_NSL
This register contains the PTP real time clock in nanoseconds low-word.
TABLE 4-149: PTP REAL TIME CLOCK IN NANOSECONDS LOW-WORD REGISTER (0X604 –
0X605): PTP_RTC_NSL
Bit
Default
R/W
Description
15 - 0
0x0000
RW
PTP Real Time Clock in Nanoseconds Low-Word [15:0]
This is low-word of the PTP real time clock in nanoseconds.
4.2.29.4
PTP Real Time Clock in Nanoseconds High-Word Register (0x606 – 0x607): PTP_RTC_NSH
This register contains the PTP real time clock in nanoseconds high-word.
TABLE 4-150: PTP REAL TIME CLOCK IN NANOSECONDS HIGH-WORD REGISTER (0X606 –
0X607): PTP_RTC_NSH
Bit
Default
R/W
Description
15 - 14
00
RW
Upper two bits in counter not used.
13 - 0
0x0000
RW
PTP Real Time Clock in Nanoseconds High-Word [29:16]
This is high-word of the PTP real time clock in nanoseconds.
4.2.29.5
PTP Real Time Clock in Seconds Low-Word Register (0x608 – 0x609): PTP_RTC_SL
This register contains the PTP real time clock in seconds low-word.
TABLE 4-151: PTP REAL TIME CLOCK IN SECONDS LOW-WORD REGISTER (0X608 – 0X609):
PTP_RTC_SL
Bit
Default
R/W
Description
15 - 0
0x0000
RW
PTP Real Time Clock in Seconds Low-Word [15:0]
This is low-word of the PTP real time clock in seconds.
4.2.29.6
PTP Real Time Clock in Seconds High-Word Register (0x60A – 0x60B): PTP_RTC_SH
This register contains the PTP real time clock in seconds high-word.
TABLE 4-152: PTP REAL TIME CLOCK IN SECONDS HIGH-WORD REGISTER (0X60A – 0X60B):
PTP_RTC_SH
Bit
Default
R/W
Description
15 - 0
0x0000
RW
PTP Real Time Clock in Seconds High-Word [31:16]
This is high-word of the PTP real time clock in seconds.
4.2.29.7
PTP Real Time Clock in Phase Register (0x60C – 0x60D): PTP_RTC_PHASE
This register indicates which sub-phase of the PTP real time clock is current. The resolution is 8 ns. The PTP real time
clock is updated every 40 ns.
TABLE 4-153: PTP REAL TIME CLOCK IN PHASE REGISTER (0X60C – 0X60D): PTP_RTC_PHASE
Bit
Default
R/W
Description
15 - 3
0x0000
RO
Reserved
DS00002642A-page 164
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-153: PTP REAL TIME CLOCK IN PHASE REGISTER (0X60C – 0X60D): PTP_RTC_PHASE
Bit
2-0
Default
000
R/W
Description
RW
PTP Real Time Clock in Sub 8ns Phase
These bits indicate one of the 8ns sub-cycle times of the 40 ns period
PTP real time clock.
000: 0 ns (real time clock at the first 8 ns cycle in 25 MHz/40 ns)
001: 8 ns (real time clock at the second 8 ns cycle in 25 MHz/40 ns)
010: 16 ns (real time clock at the third 8 ns cycle in 25 MHz/40 ns)
011: 24 ns (real time clock at the fourth 8 ns cycle in 25 MHz/40 ns)
100: 32 ns (real time clock at the fifth 8 ns cycle in 25 MHz/40 ns)
101-111: NA
This register is set to zero whenever the PTP_RTC_NSL, PTP_RTC_NSH, PTP_RTC_SL, PTP_RTC_SH registers are written to by the
CPU.
4.2.29.8
0x60E – 0x60F: Reserved
4.2.29.9
PTP Rate in Sub-Nanoseconds Low-Word Register (0x610 – 0x611): PTP_SNS_RATE_L
This register contains the PTP rate control in sub-nanoseconds low-word.
TABLE 4-154: PTP RATE IN SUB-NANOSECONDS LOW-WORD REGISTER (0X610 – 0X611):
PTP_SNS_RATE_L
Bit
15 - 0
4.2.29.10
Default
0x0000
R/W
Description
RW
PTP Rate Control in Sub-Nanoseconds Low-Word [15:0]
This is low-word of PTP rate control value in units of 2-32 ns. The PTP
rate control value is used for incrementing (PTP_RATE_DIR = “0”) or
decrementing (PTP_RATE_DIR = “1”) the frequency adjustment by the
value in PTP_SNS_RATE_H [29:16] and PTP_SNS_RATE_L [15:0] per
reference clock cycle (40 ns). On each reference clock cycle, the PTP
clock will be adjusted REF_CLK_PERIOD ±PTP_SNS_RATE_H/L value.
Setting both PTP_SNS_RATE_H/L registers value to “0x0” will disable
both continuous and temporary adjustment modes.
PTP Rate in Sub-Nanoseconds High-Word and Control Register (0x612 – 0x613):
PTP_SNS_RATE_H
This register contains the PTP rate control in sub-nanoseconds high-word and configuration.
TABLE 4-155: PTP RATE IN SUB-NANOSECONDS HIGH-WORD AND CONTROL REGISTER (0X612
– 0X613): PTP_SNS_RATE_H
Bit
15
14
Default
0
0
2018 Microchip Technology Inc.
R/W
Description
RW
Rate Direction Control for Temporary or Continuous Adjustment
Mode
(PTP_RATE_DIR)
1 = Lower frequency. The PTP_SNS_RATE_H/L value will be added to
system time clock on every 25 MHz clock cycle.
0 = Higher frequency. The PTP_SNS_RATE_H/L value will be subtracted
from system time clock on every 25 MHz clock cycle.
RW/SC
Enable Temporary Adjustment Mode for PTP 1588 Clock
(PTP_TEMP_ADJ_CLK)
1 = Enable the temporary incrementing (PTP_RATE_DIR = “0”) or decrementing (PTP_RATE_DIR = “1”) frequency adjustment by the value in
the PTP_SNS_RATE_H/L registers over the duration of time set in the
PTP_ADJ_DURA_H/L registers on every 25 MHz clock cycle. This bit is
self-cleared when the adjustment is completed. Software can read this bit
to check whether the adjustment is still in progress.
0 = Disable the temporary adjustment mode to the PTP clock.
DS00002642A-page 165
KSZ8463ML/RL/FML/FRL
TABLE 4-155: PTP RATE IN SUB-NANOSECONDS HIGH-WORD AND CONTROL REGISTER (0X612
– 0X613): PTP_SNS_RATE_H (CONTINUED)
Bit
13 - 0
4.2.29.11
Default
0x0000
R/W
Description
RW
PTP Rate Control in Sub-Nanoseconds High-Word [29:16]
(PTP_SNS_RATE_H[29:16])
This is high-word of PTP rate control value in units of 2-32 ns. The PTP
rate control value is used for incrementing (PTP_RATE_DIR = “0”) or
decrementing (PTP_RATE_DIR = “1”) the frequency adjustment by the
value in PTP_SNS_RATE_H [29:16] and PTP_SNS_RATE_L [15:0] per
reference clock cycle (40 ns). On each reference clock cycle, the PTP
clock will be adjusted by a REF_CLK_PERIOD ±PTP_SNS_RATE_H/L
value. Setting both PTP_SNS_RATE_H/L registers value to “0x0” will disable both continuous and temporary adjustment modes.
PTP Temporary Adjustment Mode Duration in Low-Word Register (0x614 – 0x615):
PTP_TEMP_ADJ_DURA_L
This register contains the PTP temporary rate adjustment duration in low-word.
TABLE 4-156: PTP TEMPORARY ADJUSTMENT MODE DURATION IN LOW-WORD REGISTER
(0X614 – 0X615): PTP_TEMP_ADJ_DURA_L
Bit
Default
R/W
Description
15 - 0
0x0000
RW
PTP Temporary Rate Adjustment Duration in Low-Word [15:0]
This register is used to set the duration for the temporary rate adjustment
in number of 25 MHz clock cycles.
4.2.29.12
PTP Temporary Adjustment Mode Duration in High-Word Register (0x616 – 0x617):
PTP_TEMP_ADJ_DURA_H
This register contains the PTP temporary rate adjustment duration in high-word.
TABLE 4-157: PTP TEMPORARY ADJUSTMENT MODE DURATION IN HIGH-WORD REGISTER
(0X616 – 0X617): PTP_TEMP_ADJ_DURA_H
Bit
Default
R/W
Description
15 - 0
0x0000
RW
PTP Temporary Rate Adjustment Duration in High-Word [31:16]
This register is used to set the duration for the temporary rate adjustment
in number of 25 MHz clock cycles.
4.2.29.13
0x618 – 0x61F: Reserved
4.2.29.14
PTP Message Configuration 1 Register (0x620 – 0x621): PTP_MSG_CFG_1
This register contains the PTP message configuration 1.
TABLE 4-158: PTP MESSAGE CONFIGURATION 1 REGISTER (0X620 – 0X621): PTP_MSG_CFG_1
Bit
Default
R/W
Description
15 - 8
0x00
RO
Reserved
7
0
RW
Enable IEEE 802.1AS Mode
Setting this bit will enable the IEEE 802.1AS mode and all PTP packets
are forwarded to port 3.
6
1
RW
Enable IEEE 1588 PTP Mode
1 = To enable the IEEE 1588 PTP mode.
0 = To disable the IEEE 1588 PTP mode.
5
0
RW
Enable Detection of IEEE 802.3 Ethernet PTP Message
1 = Enable to detect the Ethernet PTP message.
0 = Disable to detect the Ethernet PTP message.
DS00002642A-page 166
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-158: PTP MESSAGE CONFIGURATION 1 REGISTER (0X620 – 0X621): PTP_MSG_CFG_1
Bit
Default
R/W
Description
4
1
RW
Enable Detection of IPv4/UDP PTP Message
1 = Enable to detect the IPv4/UDP PTP message.
0 = Disable to detect the IPv4/UDP PTP message.
3
1
RW
Enable Detection of IPv6/UDP PTP Message
1 = Enable to detect the IPv6/UDP PTP message.
0 = Disable to detect the IPv6/UDP PTP message.
2
0
RW
Selection of P2P or E2E
1 = Select Peer-to-Peer (P2P) transparent clock mode.
0 = Select End-to-End (E2E) transparent clock mode.
1
0
RW
Selection of Master or Slave
1 = Select port 3 as master in ordinary clock mode.
0 = Select port 3 as slave in ordinary clock mode.
0
1
RW
Selection of One-step or Two-Step Operation
1 = Select one-step clock mode.
0 = Select two-step clock mode.
4.2.29.15
PTP Message Configuration 2 Register (0x622 – 0x623): PTP_MSG_CFG_2
This register contains the PTP message configuration 2.
TABLE 4-159: PTP MESSAGE CONFIGURATION 2 REGISTER (0X622 – 0X623): PTP_MSG_CFG_2
Bit
Default
R/W
15 - 13
000
RO
Reserved
RW
Enable Unicast PTP
1 = The Unicast PTP packet can be recognized. If the packet UDP destination port is either 319 or 320 and the packet MAC/IP address is not the
PTP reserved address, then the packet will be considered as Unicast
PTP packet and the packet forwarding will be decided by regular table
lookup.
0 = Only multicast PTP packet will be recognized.
RW
Enable Alternate Master
1 = Alternate master clock is supported. The Sync, Follow_Up,
Delay_Req, and Delay_Resp messages of the same domain received at
port 1/port 2 by active master clock of same domain will be forwarded to
port 2/port 1.
0 = Alternate master clock is not supported. The Sync message will not
be forwarded to the other port when this bit = “0”. The Delay_Req message of same domain received at port 1/port 2 by active master clock of
same domain will be discarded on port 3 and be forwarded to port 2/port
1 if Delay_Req is for other domains.
12
11
0
0
Description
10
1
RW
PTP Messages Priority TX Queue
1 = All PTP messages are assigned to highest priority TX queue.
0 = Only the PTP event messages are assigned to highest priority TX
queue.
9
0
RW
Enable Checking of Associated Sync and Follow_Up PTP Messages
Setting this bit will associate Follow_Up message with Sync message
under certain situations. This bit only applies to PTP frames on port 3.
2018 Microchip Technology Inc.
DS00002642A-page 167
KSZ8463ML/RL/FML/FRL
TABLE 4-159: PTP MESSAGE CONFIGURATION 2 REGISTER (0X622 – 0X623): PTP_MSG_CFG_2
Bit
8
Default
0
R/W
Description
RW
Enable Checking of Associated Delay_Req and Delay_Resp PTP
Messages
While this bit is set, the Delay_Resp message will be forwarded to port 1/
port 2 if the associations do not match and is forwarded to port 3 if the
associations match. Setting this bit will associate Delay_Resp message
with Delay_Req message when it has the same domain, sequenceID,
and sourceportID. The PTP frame will be forwarded to port 3 if the ID
matches.
7
0
RW
Enable Checking of Associated Pdelay_Req and Pdelay_Resp PTP
Messages
Setting this bit will associate Pdelay_Resp/Pdelay_Resp_Follow_Up
messages with Pdelay_Req message when it has the same domain,
sequenceID, and sourceportID. The PTP frame will be forwarded to port
3 if the ID matches. This bit only applies to PTP frames on port 3.
6
0
RO
Reserved
5
0
RW
Reserved
4
0
RW
Enable Checking of Domain Field: DOMAIN_EN
Setting this DOMAIN_EN bit will enable the device to automatically check
the domain field in PTP message with the PTP_DOMAIN_VER[7:0]. The
PTP message will be forwarded to port 3 if the domain field is matched to
PTP_DOMAIN_VER[7:0] otherwise the PTP message will be dropped.
If set this bit to “0”, regardless of domain field, PTP messages are always
forwarded to port 3 according to hardware default rules.
3
0
RO
Reserved
2
1
RW
Enable the IPv4/UDP Checksum Calculation for Egress Packets
1 = The device will re-calculate and generate a 2-byte checksum value
due to a frame contents change.
0 = The checksum field is set to zero. If the IPv4/UDP checksum is zero,
the checksum will remain zero regardless of this bit setting.
For IPv6/UDP, the checksum is always updated.
1
0
RW
Announce Message from Port 1
1 = The Announce message is received from port 1 direction.
0 = The Announce message is not received from port 1 direction.
0
0
RW
Announce Message from Port 2
1 = The Announce message is received from port 2 direction.
0 = The Announce message is not received from port 2 direction.
4.2.29.16
PTP Domain and Version Register (0x624 – 0x625): PTP_DOMAIN_VER
This register contains the PTP Domain and Version Information.
TABLE 4-160: PTP DOMAIN AND VERSION REGISTER (0X624 – 0X625): PTP_DOMAIN_VER
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
RW
PTP Version
This is the value of PTP message version number field. All PTP packets
will be captured when the receive PTP message version matches the
value in this field.
All PTP packets will be dropped if the receive PTP message version does
not match the value in this field. Except for the value of version 1, the
device is always forwarding PTP packets between port 1 and port 2, and
not to port 3.
11 - 8
0x2
DS00002642A-page 168
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-160: PTP DOMAIN AND VERSION REGISTER (0X624 – 0X625): PTP_DOMAIN_VER
Bit
7-0
Default
0x00
R/W
Description
RW
PTP Domain
This is the value of the PTP message domain number field. If the
DOMAIN_EN bit is set to “1”, the PTP messages will be filtered out and
only forwarded to port 3 if the domain number matches.
If the DOMAIN_EN bit is set to “0”, the domain number field will be
ignored under certain circumstances.
4.2.29.17
0x626 – 0x63F: Reserved
4.2.29.18
PTP Port 1 Receive Latency Register (0x640 – 0x641): PTP_P1_RX_LATENCY
This register contains the PTP port 1 receive latency value in nanoseconds.
TABLE 4-161: PTP PORT 1 RECEIVE LATENCY REGISTER (0X640 – 0X641):
PTP_P1_RX_LATENCY
Bit
Default
R/W
Description
15 - 0
0x019F
RW
PTP Port 1 RX Latency in Nanoseconds [15:0]
This register is used to set the fixed receive delay value from port 1 wire
to RX time stamp reference point. The default value is 415 ns.
4.2.29.19
PTP Port 1 Transmit Latency Register (0x642 – 0x643): PTP_P1_TX_LATENCY
This register contains the PTP port 1 transmit latency value in nanoseconds.
TABLE 4-162: PTP PORT 1 TRANSMIT LATENCY REGISTER (0X642 – 0X643):
PTP_P1_TX_LATENCY
Bit
Default
R/W
Description
15 - 0
0x002D
RW
PTP Port 1 TX Latency in Nanoseconds [15:0]
This register is used to set the fixed transmit delay value from port 1 TX
time stamp reference point to wire. The default value is 45 ns.
4.2.29.20
PTP Port 1 Asymmetry Correction Register (0x644 – 0x645): PTP_P1_ASYM_COR
This register contains the PTP port 1 asymmetry correction value in nanoseconds.
TABLE 4-163: PTP PORT 1 ASYMMETRY CORRECTION REGISTER (0X644 – 0X645):
PTP_P1_ASYM_COR
Bit
Default
R/W
Description
15
0
RW
PTP Port 1 Asymmetry Correction Sign Bit
1 = The magnitude in bit[14:0] is negative.
0 = The magnitude in bit[14:0] is positive.
RW
PTP Port 1 Asymmetry Correction in Nanoseconds [14:0]
This register is used to set the fixed asymmetry value to add in the correction field for ingress Sync and Pdelay_Resp or to subtract from correction field for egress Delay_Req and Pdelay_Req.
14 - 0
4.2.29.21
0x0000
PTP Port 1 Link Delay Register (0x646 – 0x647): PTP_P1_LINK_DLY
This register contains the PTP port 1 link delay in nanoseconds.
TABLE 4-164: PTP PORT 1 LINK DELAY REGISTER (0X646 – 0X647): PTP_P1_LINK_DLY
Bit
Default
R/W
Description
15 - 0
0x0000
RW
PTP Port 1 Link Delay in Nanoseconds [15:0]
This register is used to set the link delay value between port 1 and link
partner port.
2018 Microchip Technology Inc.
DS00002642A-page 169
KSZ8463ML/RL/FML/FRL
4.2.29.22
PTP Port 1 Egress Time stamp Low-Word Register for Pdelay_Req and Delay_Req (0x648 –
0x649): P1_XDLY_REQ_TSL
This register contains the PTP port 1 egress time stamp low-word value for Pdelay_Req and Delay_Req frames in nanoseconds.
TABLE 4-165: PTP PORT 1 EGRESS TIME STAMP LOW-WORD REGISTER FOR PDELAY_REQ
AND DELAY_REQ (0X648 – 0X649): P1_XDLY_REQ_TSL
Bit
15 - 0
4.2.29.23
Default
0x0000
R/W
Description
RW
PTP Port 1 Egress Time stamp for Pdelay_Req and Delay_Req in
Nanoseconds [15:0]
This register contains port 1 egress time stamp low-word value for Pdelay_Req and Delay_Req frames in nanoseconds.
PTP Port 1 Egress Time stamp High-Word Register for Pdelay_Req and Delay_Req (0x64A –
0x64B): P1_XDLY_REQ_TSH
This register contains the PTP port 1 egress time stamp high-word value for Pdelay_Req and Delay_Req frames in
nanoseconds.
TABLE 4-166: PTP PORT 1 EGRESS TIME STAMP HIGH-WORD REGISTER FOR PDELAY_REQ
AND DELAY_REQ (0X64A – 0X64B): P1_XDLY_REQ_TSH
Bit
15 - 14
13 - 0
4.2.29.24
Default
00
0x0000
R/W
Description
RW
PTP Port 1 Egress Time stamp for Pdelay_Req and Delay_Req in
Seconds [1:0]
These bits are bits [1:0] of the port 1 egress time stamp value for Pdelay_Req and Delay_Req frames in seconds.
RW
PTP Port 1 Egress Time stamp for Pdelay_Req and Delay_Req in
Nanoseconds [29:16]
These bits are bits [29:16] of the port 1 egress time stamp value for Pdelay_Req and Delay_Req frames in nanoseconds.
PTP Port 1 Egress Time stamp Low-Word Register for Sync (0x64C – 0x64D):
P1_SYNC_TSL
This register contains the PTP port 1 egress time stamp low-word value for Sync frame in nanoseconds.
TABLE 4-167: PTP PORT 1 EGRESS TIME STAMP LOW-WORD REGISTER FOR SYNC (0X64C –
0X64D): P1_SYNC_TSL
Bit
Default
R/W
Description
15 - 0
0x0000
RW
PTP Port 1 Egress Time stamp for Sync in Nanoseconds [15:0]
This register contains port 1 egress time stamp low-word value for Sync
frame in nanoseconds.
4.2.29.25
PTP Port 1 Egress Time stamp High-Word Register for Sync (0x64E – 0x64F):
P1_SYNC_TSH
This register contains the PTP port 1 egress time stamp high-word value for Sync frame in nanoseconds.
TABLE 4-168: PTP PORT 1 EGRESS TIME STAMP HIGH-WORD REGISTER FOR SYNC (0X64E –
0X64F): P1_SYNC_TSH
Bit
Default
R/W
Description
15 - 14
00
RW
PTP Port 1 Egress Time stamp for Sync in Seconds [1:0]
These bits are bits [1:0] of the port 1 egress time stamp value for Sync
frame in seconds.
13 - 0
0x0000
RW
PTP Port 1 Egress Time stamp for Sync in Nanoseconds [29:16]
These bits are bits [29:16] of the Port 1 egress time stamp value for Sync
frame in nanoseconds.
DS00002642A-page 170
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.29.26
PTP Port 1 Egress Time stamp Low-Word Register for Pdelay_Resp (0x650 – 0x651):
P1_PDLY_RESP_TSL
This register contains the PTP port 1 egress time stamp low-word value for Pdelay_Resp frame in nanoseconds.
TABLE 4-169: PTP PORT 1 EGRESS TIME STAMP LOW-WORD REGISTER FOR PDELAY_RESP
(0X650 – 0X651): P1_PDLY_RESP_TSL
Bit
15 - 0
4.2.29.27
Default
0x0000
R/W
Description
RW
PTP Port 1 Egress Time stamp for Pdelay_Resp in Nanoseconds
[15:0]
This register contains port 1 egress time stamp low-word value for Pdelay_Resp frame in nanoseconds.
PTP Port 1 Egress Time stamp High-Word Register for Pdelay_Resp (0x652 – 0x653):
P1_PDLY_RESP_TSH
This register contains the PTP port 1 egress time stamp high-word value for Pdelay_Resp frame in nanoseconds.
TABLE 4-170: PTP PORT 1 EGRESS TIME STAMP HIGH-WORD REGISTER FOR PDELAY_RESP
(0X652 – 0X653): P1_PDLY_RESP_TSH
Bit
Default
R/W
Description
15 - 14
00
RW
PTP Port 1 Egress Time stamp for Pdelay_Resp in Seconds [1:0]
These bits are bits [1:0] of the port 1 egress time stamp value for Pdelay_Resp frame in seconds.
RW
PTP Port 1 Egress Time stamp for Pdelay_Resp in Nanoseconds
[29:16]
These bits are bits [29:16] of the port 1 egress time stamp high-word
value for Pdelay_Resp frame in nanoseconds.
13 - 0
0x0000
4.2.29.28
0x654 – 0x65F: Reserved
4.2.29.29
PTP Port 2 Receive Latency Register (0x660 – 0x661): PTP_P2_RX_LATENCY
This register contains the PTP port 2 receive latency value in nanoseconds.
TABLE 4-171: PTP PORT 2 RECEIVE LATENCY REGISTER (0X660 – 0X661):
PTP_P2_RX_LATENCY
Bit
Default
R/W
Description
15 - 0
0x019F
RW
PTP Port 2 RX Latency in Nanoseconds [15:0]
This register is used to set the fixed receive delay value from port 2 wire
to the RX time stamp reference point. The default value is 415 ns.
4.2.29.30
PTP Port 2 Transmit Latency Register (0x662 – 0x663): PTP_P2_TX_LATENCY
This register contains the PTP port 2 transmit latency value in nanoseconds.
TABLE 4-172: PTP PORT 2 TRANSMIT LATENCY REGISTER (0X662 – 0X663):
PTP_P2_TX_LATENCY
Bit
Default
R/W
Description
15 - 0
0x002D
RW
PTP Port 2 TX Latency in Nanoseconds [15:0]
This register is used to set the fixed transmit delay value from port 2 TX
time stamp reference point to the wire. The default value is 45 ns.
2018 Microchip Technology Inc.
DS00002642A-page 171
KSZ8463ML/RL/FML/FRL
4.2.29.31
PTP Port 2 Asymmetry Correction Register (0x664 – 0x665): PTP_P2_ASYM_COR
This register contains the PTP port 2 asymmetry correction value in nanoseconds.
TABLE 4-173: PTP PORT 2 ASYMMETRY CORRECTION REGISTER (0X664 – 0X665):
PTP_P2_ASYM_COR
Bit
Default
R/W
Description
15
0
RW
PTP Port 2 Asymmetry Correction Sign Bit
1 = The magnitude in bit[14:0] is negative.
0 = The magnitude in bit[14:0] is positive.
RW
PTP Port 2 Asymmetry Correction in Nanoseconds [14:0]
This register is used to set the fixed asymmetry value to add in the correction field for ingress Sync and Pdelay_Resp or to subtract from correction field for egress Delay_Req and Pdelay_Req.
14 - 0
4.2.29.32
0x0000
PTP Port 2 Link Delay Register (0x666 – 0x667): PTP_P2_LINK_DLY
This register contains the PTP port 2 link delay in nanoseconds.
TABLE 4-174: PTP PORT 2 LINK DELAY REGISTER (0X666 – 0X667): PTP_P2_LINK_DLY
Bit
Default
R/W
Description
15 - 0
0x0000
RW
PTP Port 2 Link Delay in Nanoseconds [15:0]
This register is used to set the link delay value between port 2 and link
partner port.
4.2.29.33
PTP Port 2 Egress Time stamp Low-Word Register for Pdelay_Req and Delay_Req (0x668 –
0x669): P2_XDLY_REQ_TSL
This register contains the PTP port 2 egress time stamp low-word value for Pdelay_Req and Delay_Req frames in nanoseconds.
TABLE 4-175: PTP PORT 2 EGRESS TIME STAMP LOW-WORD REGISTER FOR PDELAY_REQ
AND DELAY_REQ (0X668 – 0X669): P2_XDLY_REQ_TSL
Bit
15 - 0
4.2.29.34
Default
0x0000
R/W
Description
RW
PTP Port 2 Egress Time stamp for Pdelay_Req and Delay_Req in
Nanoseconds [15:0]
This register contains port 2 egress time stamp low-word value for Pdelay_Req and Delay_Req frames in nanoseconds.
PTP Port 2 Egress Time stamp High-Word Register for Pdelay_Req and Delay_Req (0x66A –
0x66B): P2_XDLY_REQ_TSH
This register contains the PTP port 2 egress time stamp high-word value for Pdelay_Req and Delay_Req frames in
nanoseconds.
TABLE 4-176: PTP PORT 2 EGRESS TIME STAMP HIGH-WORD REGISTER FOR PDELAY_REQ
AND DELAY_REQ (0X66A – 0X66B): P2_XDLY_REQ_TSH
Bit
15 - 14
13 - 0
Default
00
0x0000
DS00002642A-page 172
R/W
Description
RW
PTP Port 2 Egress Time stamp for Pdelay_Req and Delay_Req in
Seconds [1:0]
These are bits [1:0] of the port 2 egress time stamp value for Pdelay_Req
and Delay_Req frames in seconds.
RW
PTP Port 2 Egress Time stamp for Pdelay_Req and Delay_Req in
Nanoseconds [29:16]
These are bits [29:16] of the port 2 egress time stamp value for Pdelay_Req and Delay_Req frames in nanoseconds.
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.29.35
PTP Port 2 Egress Time stamp Low-Word Register for Sync (0x66C – 0x66D):
P2_SYNC_TSL
This register contains the PTP port 2 egress time stamp low-word value for Sync frame in nanoseconds.
TABLE 4-177: PTP PORT 2 EGRESS TIME STAMP LOW-WORD REGISTER FOR SYNC (0X66C –
0X66D): P2_SYNC_TSL
Bit
Default
R/W
Description
15 - 0
0x0000
RW
PTP Port 2 Egress Time stamp for Sync in Nanoseconds [15:0]
This register contains port 2 egress time stamp low-word value for Sync
frame in nanoseconds.
4.2.29.36
PTP Port 2 Egress Time stamp High-Word Register for Sync (0x66E – 0x66F):
P2_SYNC_TSH
This register contains the PTP port 2 egress time stamp high-word value for Sync frame in nanoseconds.
TABLE 4-178: PTP PORT 2 EGRESS TIME STAMP HIGH-WORD REGISTER FOR SYNC (0X66E –
0X66F): P2_SYNC_TSH
Bit
Default
R/W
Description
15 - 14
00
RW
PTP Port 2 Egress Time stamp for Sync in Seconds [1:0]
These are bits [1:0] of the port 2 egress time stamp value for Sync frame
in seconds.
13 - 0
0x0000
RW
PTP Port 2 Egress Time stamp for Sync Nanoseconds [29:16]
These are bits [29:16] of the port 2 egress time stamp value for Sync
frame in nanoseconds.
4.2.29.37
PTP Port 2 Egress Time stamp Low-Word Register for Pdelay_Resp (0x670 – 0x671):
P2_PDLY_RESP_TSL
This register contains the PTP port 2 egress time stamp low-word value for Pdelay_Resp frame in nanoseconds.
TABLE 4-179: PTP PORT 2 EGRESS TIME STAMP LOW-WORD REGISTER FOR PDELAY_RESP
(0X670 – 0X671): P2_PDLY_RESP_TSL
Bit
15 - 0
4.2.29.38
Default
0x0000
R/W
Description
RW
PTP Port 2 Egress Time stamp for Pdelay_Resp in Nanoseconds
[15:0]
This register contains port 2 egress time stamp low-word value for Pdelay_Resp frame in nanoseconds.
PTP Port 2 Egress Time stamp High-Word Register for Pdelay_Resp (0x672 – 0x673):
P2_PDLY_RESP_TSH
This register contains the PTP port 2 egress time stamp high-word value for Pdelay_Resp frame in nanoseconds.
TABLE 4-180: PTP PORT 2 EGRESS TIME STAMP HIGH-WORD REGISTER FOR PDELAY_RESP
(0X672 – 0X673): P2_PDLY_RESP_TSH
Bit
15 - 0
4.2.29.39
Default
0x0000
R/W
Description
RW
PTP Port 2 Egress Time stamp for Pdelay_Resp in Nanoseconds
[31:16]
This register contains port 2 egress time stamp high-word value for Pdelay_Resp frame in nanoseconds.
0x674 – 0x67F: Reserved
2018 Microchip Technology Inc.
DS00002642A-page 173
KSZ8463ML/RL/FML/FRL
4.2.29.40
GPIO Monitor Register (0x680 – 0x681): GPIO_MONITOR
This register contains read-only access for the current values on GPIO inputs.
TABLE 4-181: GPIO MONITOR REGISTER (0X680 – 0X681): GPIO_MONITOR
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
11 - 0
0x000
RO
GPIO Inputs Monitor
This field reflects the current values seen on the GPIO inputs. GPIOs 11
through 0 are mapped to bits [11:0] in order.
4.2.29.41
GPIO Output Enable Register (0x682 – 0x683): GPIO_OEN
This register contains the control bits for GPIO output enable.
TABLE 4-182: GPIO OUTPUT ENABLE REGISTER (0X682 – 0X683): GPIO_OEN
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
RW
GPIO Output Enable
0 = Enables the GPIO pin as trigger output.
1 = Enables the GPIO pin as time stamp input.
GPIOs 11 through 0 are mapped to bits [11:0] in order.
11 - 0
0x000
4.2.29.42
0x684 – 0x687: Reserved
4.2.29.43
PTP Trigger Unit Interrupt Status Register (0x688 – 0x689): PTP_TRIG_IS
This register contains the interrupt status of PTP event trigger units.
TABLE 4-183: PTP TRIGGER UNIT INTERRUPT STATUS REGISTER (0X688 – 0X689):
PTP_TRIG_IS
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
11 - 0
4.2.29.44
0x000
Trigger Output Unit Interrupt Status
When this bit is set to 1, it indicates that the trigger output unit is done or
has an error. The trigger output units from 12 to 1 are mapped to bit
[11:0].
RO (W1C)
These 12 trigger output unit interrupt status bits are logical OR’ed
together and connected to ISR bit [10].
Any of the interrupt status bits are cleared by writing a “1” to the particular
bit.
PTP Trigger Unit Interrupt Enable Register (0x68A – 0x68B): PTP_TRIG_IE
This register contains the interrupt enable of PTP trigger output units.
TABLE 4-184: PTP TRIGGER UNIT INTERRUPT ENABLE REGISTER (0X68A – 0X68B):
PTP_TRIG_IE
Bit
Default
R/W
Description
15 - 12
0x0
RO
Reserved
RW
Trigger Output Unit Interrupt Enable
When this bit is set to “1”, it indicates that the trigger output unit interrupt
is enabled.
The trigger output units from 12 to 1 are mapped to bit [11:0].
These 12 trigger output unit interrupt enables are logical OR’ed together
and connected to IER bit [10].
11 - 0
0x000
DS00002642A-page 174
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.29.45
PTP Time stamp Unit Interrupt Status Register (0x68C – 0x68D): PTP_TS_IS
This register contains the interrupt status of PTP time stamp units. Each bit in this register is cleared by writing a “1” to it.
TABLE 4-185: PTP TIME STAMP UNIT INTERRUPT STATUS REGISTER (0X68C – 0X68D):
PTP_TS_IS
Bit
15
14
13
12
11 - 0
4.2.29.46
Default
R/W
Description
0
Port 2 Egress Time stamp for Pdelay_Req/Resp and Delay_Req
Frames Interrupt Status
When this bit is set to “1”, it indicates that the egress time stamp is availRO (W1C)
able from port 2 for Pdelay_Req/Resp and Delay_Req frames.
This bit will be logical OR’ed together with the rest of bits in this register
and the logical OR’ed output is connected to ISR bit[12].
0
Port 2 Egress Time stamp for Sync Frame Interrupt Status
When this bit is set to “1”, it indicates that the egress time stamp is availRO (W1C) able from port 2 for Sync frame.
This bit will be logical OR’ed together with the rest of bits in this register
and the logical OR’ed output is connected to ISR bit[12].
0
Port 1 Egress Time stamp for Pdelay_Req/Resp and Delay_Req
Frames Interrupt Status
When this bit is set to “1”, it indicates that the egress time stamp is availRO (W1C)
able from port 1 for Pdelay_Req/Resp and Delay_Req frames.
This bit will be logical OR’ed together with the rest of bits in this register
and the logical OR’ed output is connected to ISR bit[12].
0
Port 1 Egress Time stamp for Sync Frame Interrupt Status
When this bit is set to “1”, it indicates that the egress time stamp is availRO (W1C) able from port 1 for Sync frame.
This bit will be logical OR’ed together with the rest of bits in this register
and the logical OR’ed output is connected to ISR bit[12].
0x000
Time stamp Unit Interrupt Status
When this bit is set to “1”, it indicates that the time stamp unit is ready
(TS_RDY = “1”).
RO (W1C) The time stamp units from 12 to 1 are mapped to bit [11:0].
These 12 time stamp interrupts status are logical OR’ed together with the
rest of bits in this register and the logical OR’ed output is connected to
ISR bit[12].
PTP Time stamp Unit Interrupt Enable Register (0x68E – 0x68F): PTP_TS_IE
This register contains the interrupt enable of PTP time stamp units.
TABLE 4-186: PTP TIME STAMP UNIT INTERRUPT ENABLE REGISTER (0X68E – 0X68F):
PTP_TS_IE
Bit
15
14
Default
0
0
2018 Microchip Technology Inc.
R/W
Description
RW
Port 2 Egress Time stamp for Pdelay_Req/Resp and Delay_Req
Frames Interrupt Enable
When this bit is set to “1”, it is enabled the interrupt when the egress time
stamp is available from port 2 for Pdelay_Req/Resp and Delay_Req
frames.
This bit will be logical OR’ed together with the rest of bits in this register
and the logical OR’ed output is connected to IER bit[12].
RW
Port 2 Egress Time stamp for Sync Frame Interrupt Enable
When this bit is set to “1”, it is enabled the interrupt when the egress time
stamp is available from port 2 for Sync frame.
This bit will be logical OR’ed together with the rest of bits in this register
and the logical OR’ed output is connected to IER bit[12].
DS00002642A-page 175
KSZ8463ML/RL/FML/FRL
TABLE 4-186: PTP TIME STAMP UNIT INTERRUPT ENABLE REGISTER (0X68E – 0X68F):
PTP_TS_IE (CONTINUED)
Bit
13
12
11 - 0
Default
0
0
0x000
R/W
Description
RW
Port 1 Egress Time stamp for Pdelay_Req/Resp and Delay_Req
Frames Interrupt Enable
When this bit is set to “1”, it is enabled the interrupt when the egress time
stamp is available from port 1 for Pdelay_Req/Resp and Delay_Req
frames.
This bit will be logical OR’ed together with the rest of bits in this register
and the logical OR’ed output is connected to IER bit[12].
RW
Port 1 Egress Time stamp for Sync Frame Interrupt Enable
When this bit is set to “1”, it is enabled the interrupt when the egress time
stamp is available from port 1 for Sync frame.
This bit will be logical OR’ed together with the rest of bits in this register
and the logical OR’ed output is connected to IER bit[12].
RW
Time stamp Unit Interrupt Enable
When this bit is set to “1”, it indicates that the time stamp unit interrupt is
enabled.
The time stamp units from 12 to 1 are mapped to bit[11:0].
These 12 time stamp interrupts enable are logical OR’ed together with
the rest of bits in this register and the logical OR’ed output is connected
to IER bit[12].
4.2.29.47
0x690 – 0x733: Reserved
4.2.29.48
DSP Control 1 Register (0x734 – 0x735): DSP_CNTRL_6
This register contains control bits for the DSP block.
TABLE 4-187: DSP CONTROL 1 REGISTER (0X734 – 0X735): DSP_CNTRL_6
Bit
Default
R/W
Description
15 - 14
00
RW
Reserved
13
1
RW
Receiver Adjustment
Set this bit to “1” when both ports 1 and 2 are in copper mode. When port
1 and/or port 2 is in fiber mode, this bit should be cleared to “0”.
Note that the fiber or copper mode is selected in the CFGR register
(0x0D8 – 0x0D9).
12 - 0
0x1020
RW
Reserved
4.2.29.49
0x736 – 0x747: Reserved
4.2.29.50
Analog Control 1 Register (0x748 – 0x749): ANA_CNTRL_1
This register contains control bits for the analog block.
TABLE 4-188: ANALOG CONTROL 1 REGISTER (0X748 – 0X749): ANA_CNTRL_1
Bit
Default
R/W
Description
15 - 8
0x00
RW
Reserved
7
0
RW
LDO Off
This bit is used to control the on/off state of the internal low-voltage regulator.
0 = LDO On (Default)
1 = Turn LDO Off
6-0
0x00
RW
Reserved
DS00002642A-page 176
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
4.2.29.51
0x74A – 0x74B: Reserved
4.2.29.52
Analog Control 3 Register (0x74C – 0x74D): ANA_CNTRL_3
This register contains control bits for the analog block.
TABLE 4-189: ANALOG CONTROL 3 REGISTER (0X74C – 0X74D): ANA_CNTRL_3
Bit
Default
R/W
Description
15
0
RW
HIPLS3 Mask
This bit must be set prior to initiating the LinkMD function.
14 - 4
0x000
RW
Reserved
3
0
RW
BTRX Reduce
This bit must be set prior to initiating the LinkMD function.
2-0
000
RW
Reserved
4.2.29.53
4.3
0x74E – 0x7FF: Reserved
MII Management (MIIM) Registers
The MIIM interface is used to access the MII PHY registers within the two embedded PHY blocks. The SPI interface
can also be used to access these registers. The latter three interfaces use a different mapping mechanism than the
MIIM interface. Note that when accessing these registers via the SPI interface, the relative order of the registers is not
exactly the same.
The “PHYADs” by defaults are assigned “0x1” for PHY1 (port 1) and “0x2” for PHY2 (port 2).
The “REGAD” supported addresses are 0x0-0x5, 0x1D and 0x1F.
TABLE 4-190: PHY REGISTER MAPPING USING THE MII INTERFACE
PHY and Register Address
Description
PHYAD = 0x1, REGAD = 0x0
PHY1 Basic Control Register
PHYAD = 0x1, REGAD = 0x1
PHY1 Basic Status Register
PHYAD = 0x1, REGAD = 0x2
PHY1 Physical Identifier I
PHYAD = 0x1, REGAD = 0x3
PHY1 Physical Identifier II
PHYAD = 0x1, REGAD = 0x4
PHY1 Auto-Negotiation Advertisement Register
PHYAD = 0x1, REGAD = 0x5
PHY1 Auto-Negotiation Link Partner Ability Register
PHYAD = 0x1, 0x6 – 0x1C
PHY1 Not supported
PHYAD = 0x1, 0x1D
PHY1 LinkMD Control/Status
PHYAD = 0x1, 0x1E
PHY1 Not supported
PHYAD = 0x1, 0x1F
PHY1 Special Control/Status
PHYAD = 0x2, REGAD = 0x0
PHY2 Basic Control Register
PHYAD = 0x2, REGAD = 0x1
PHY2 Basic Status Register
PHYAD = 0x2, REGAD = 0x2
PHY2 Physical Identifier I
PHYAD = 0x2, REGAD = 0x3
PHY2 Physical Identifier II
PHYAD = 0x2, REGAD = 0x4
PHY2 Auto-Negotiation Advertisement Register
PHYAD = 0x2, REGAD = 0x5
PHY2 Auto-Negotiation Link Partner Ability Register
PHYAD = 0x2, 0x6 – 0x1C
PHYAD = 0x2, 0x1D
PHY2 Not supported
PHY2 LinkMD Control/Status
PHYAD = 0x2, 0x1E
PHY2 Not supported
PHYAD = 0x2, 0x1F
PHY2 Special Control/Status
2018 Microchip Technology Inc.
DS00002642A-page 177
KSZ8463ML/RL/FML/FRL
TABLE 4-191: PHY1 (PHYAD = 0X1) AND PHY2 (PHYAD = 0X2): REGISTER 0 (REGAD = 0X0) -> MII
BASIC CONTROL
Bit
Default
R/W
Description
15
0
RO
Reserved
14
0
RW
Far-End Loopback
1 = Perform port 1 loopback example as follows:
Start: RXP2/RXM2 (port 2)
Loopback: PMD/PMA of port 1’s PHY
End: TXP2/TXM2 (port 2)
0 = Normal operation.
13
0
RW
Force 100BASE-TX
1 = Force 100 Mbps if auto-negotiation is disabled (bit[12])
0 = Force 10 Mbps if auto-negotiation is disabled (bit[12])
12
1
RW
Auto-Negotiation Enable
1 = Auto-negotiation enabled.
0 = Auto-negotiation disabled.
11
0
RW
Power-Down
1 = Power-down.
0 = Normal operation.
10
0
RO
Isolate
Not supported.
9
0
RW
Restart Auto-Negotiation
1 = Restart auto-negotiation.
0 = Normal operation.
8
0
RW
Force Full-Duplex
1 = Force full-duplex.
0 = Force half-duplex.
Applies if auto-negotiation is disabled.
It is always in half-duplex if auto-negotiation is enabled but failed.
7
0
RO
Collision Test
Not supported.
6
0
RO
Reserved
5
1
RW
HP_MDIX
1 = HP Auto-MDI-X mode.
0 = Microchip Auto-MDI-X mode.
4
0
RW
Force MDI-X
1 = Force MDI-X.
0 = Normal operation.
3
0
RW
Disable Auto-MDI-X
1 = Disable Auto-MDI-X.
0 = Normal operation.
2
0
RW
Disable Far-End Fault
1 = Disable far-end fault detection.
0 = Normal operation.
For 100BASE-FX fiber mode operation.
1
0
RW
Disable Transmit
1 = Disable transmit.
0 = Normal operation.
0
0
RW
Disable LED
1 = Disable LED.
0 = Normal operation.
DS00002642A-page 178
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-192: PHY1 (PHYAD = 0X1) AND PHY2 (PHYAD = 0X2): REGISTER 1 (REGAD = 0X1) -> MII
BASIC STATUS
Bit
Default
R/W
Description
15
0
RO
T4 Capable
1 = 100 BASE-T4 capable.
0 = Not 100 BASE-T4 capable.
14
1
RO
100BASE-TX Full Capable
1 = 100BASE-TX full-duplex capable.
0 = Not 100BASE-TX full-duplex capable.
13
1
RO
100BASE-TX Half Capable
1 = 100BASE-TX half-duplex capable.
0 = Not 100BASE-TX half-duplex capable.
12
1
RO
10BASE-T Full Capable
1 = 10BASE-T full-duplex capable.
0 = Not 10BASE-T full-duplex capable.
11
1
RO
10BASE-T Half Capable
1 = 10BASE-T half-duplex capable.
0 = Not 10BASE-T half-duplex capable.
10 - 7
0x0
RO
Reserved
6
0
RO
Preamble Suppressed
Not supported.
5
0
RO
Auto-Negotiation Complete
1 = Auto-negotiation complete.
0 = Auto-negotiation not completed.
4
0
RO
Far-End Fault
1 = Far-end fault detected.
0 = No far-end fault detected.
For 100BASE-FX fiber-mode operation.
3
1
RO
Auto-Negotiation Capable
1 = Auto-negotiation capable.
0 = Not auto-negotiation capable.
2
0
RO
Link Status
1 = Link is up.
0 = Link is down.
1
0
RO
Jabber Test
Not supported.
0
0
RO
Extended Capable
1 = Extended register capable.
0 = Not extended register capable.
TABLE 4-193: PHY1 (PHYAD = 0X1) AND PHY2 (PHYAD = 0X2): REGISTER 2 (REGAD = 0X2) ->
PHYID HIGH
Bit
Default
R/W
Description
15 - 0
0x0022
RO
PHY ID High Word
TABLE 4-194: PHY1 (PHYAD = 0X1) AND PHY2 (PHYAD = 0X2): REGISTER 3 (REGAD = 0X3) ->
PHYID LOW
Bit
Default
R/W
Description
15 - 0
0x1430
RO
PHY ID Low Word
2018 Microchip Technology Inc.
DS00002642A-page 179
KSZ8463ML/RL/FML/FRL
TABLE 4-195: PHY1 (PHYAD = 0X1) AND PHY2 (PHYAD = 0X2): REG. 4 (REGAD = 0X4) -> AUTONEGOTIATION ADVERTISEMENT ABILITY
Bit
Default
R/W
Description
15
0
RO
Next Page
Not supported.
14
0
RO
Reserved
13
0
RO
Remote Fault
Not supported.
12 - 11
0x0
RO
Reserved
10
1
RW
Pause (Flow Control Capability)
1 = Advertise pause ability.
0 = Do not advertise pause capability.
9
0
RW
Reserved
8
1
RW
Advertise 100BASE-TX Full-Duplex
1 = Advertise 100BASE-TX full-duplex capable.
0 = Do not advertise 100BASE-TX full-duplex capability.
7
1
RW
Advertise 100BASE-TX Half-Duplex
1= Advertise 100BASE-TX half-duplex capable.
0 = Do not advertise 100BASE-TX half-duplex capability.
6
1
RW
Advertise 10BASE-T Full-Duplex
1 = Advertise 10BASE-T full-duplex capable.
0 = Do not advertise 10BASE-T full-duplex capability.
5
1
RW
Advertise 10BASE-T Half-Duplex
1 = Advertise 10BASE-T half-duplex capable.
0 = Do not advertise 10BASE-T half-duplex capability.
4-0
0x01
RO
Selector Field
802.3
TABLE 4-196: PHY1 (PHYAD = 0X1) AND PHY2 (PHYAD = 0X2): REG. 5 (REGAD = 0X5) -> AUTONEGOTIATION LINK PARTNER ABILITY
Bit
Default
R/W
Description
15
0
RO
Next Page
Not supported.
14
0
RO
LP ACK
Not supported.
13
0
RO
Remote Fault
Not supported.
12 - 11
0x0
RO
Reserved
10
0
RO
Pause
Link partner pause capability.
9
0
RO
Reserved
8
0
RO
Advertise 100BASE-TX Full-Duplex
Link partner 100BASE-TX full capability.
7
0
RO
Advertise 100BASE-TX Half-Duplex
Link partner 100 half capability.
6
0
RO
Advertise 10BASE-T Full-Duplex
Link partner 10BASE-T full capability.
5
0
RO
Advertise 10BASE-T Half-Duplex
Link partner 10BASE-T half capability.
4-0
0x1
RO
Reserved
DS00002642A-page 180
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-197: PHY1 (PHYAD = 0X1) AND PHY2 (PHYAD = 0X2): REG. 29 (REGAD = 0X1D) ->
LINKMD CONTROL AND STATUS
Bit
15
Default
0
R/W
RW/SC
Description
Cable Diagnostic Test Enable
1 = Cable diagnostic test is enabled. It is self-cleared after the test is
done.
0 = Indicates that the cable diagnostic test has completed and the status
information is valid for read.
14 - 13
0x0
RO
Cable Diagnostic Test Results
[00] = Normal condition.
[01] = Open condition detected in the cable.
[10] = Short condition detected in the cable.
[11] = Cable diagnostic test has failed.
12
—
RO
CDT 10M Short
1 = Less than 10m short.
11 - 9
0x0
RO
Reserved
8-0
0x000
RO
CDT_Fault_Count
Distance to the fault. The distance is approximately 0.4m*CDT_Fault_Count.
TABLE 4-198: PHY1 (PHYAD = 0X1) AND PHY2 (PHYAD = 0X2): REG. 31 (REGAD = 0X1F) -> PHY
SPECIAL CONTROL AND STATUS
Bit
Default
R/W
Description
15 - 6
0x000
RO
Reserved
5
0
RO
Polarity Reverse
1 = Polarity is reversed.
0 = Polarity is not reversed.
4
0
RO
MDI-X Status
0 = MDI
1 = MDI-X
3
0
RW
Force Link
1 = Force link pass.
0 = Normal operation.
2
1
RW
Enable Energy Efficient Ethernet (EEE) on 10BASE-Te
1 = Disable 10BASE-Te.
0 = Enable 10BASE-Te.
1
0
RW
Remote (Near-End) Loopback
1 = Perform remote loopback at
Port 1's PHY (RXP1/RXM1 -> TXP1/TXM1)
Port 2's PHY (RXP2/RXM2 -> TXP2/TXM2)
0 = Normal operation
0
0
RW
Reserved
2018 Microchip Technology Inc.
DS00002642A-page 181
KSZ8463ML/RL/FML/FRL
4.4
Management Information Base (MIB) Counters
The KSZ8463 provides 34 MIB counters for each port. These counters are used to monitor the port activity for network
management. The MIB counters are formatted “per port” and “all ports dropped packet” as shown in Table 4-199.
TABLE 4-199: FORMAT OF PER-PORT MIB COUNTERS
Bit
Name
R/W
Description
Default
31
Overflow
RO
1 = Counter overflow.
0 = No counter overflow.
0
30
Count Valid
RO
1 = Counter value is valid.
0 = Counter value is not valid.
0
29 - 0
Counter Values
RO
Counter value (read clear)
0x00000000
“Per Port” MIB counters are read using indirect memory access. The base address offsets and address ranges for all
three ports are:
Port 1, base address is 0x00 and range is from 0x00 to 0x1F.
Port 2, base address is 0x20 and range is from 0x20 to 0x3F.
Port 3 (Host MII/RMII), base address is 0x40 and range is from 0x40 to 0x5F.
“Per Port” MIB counters are read using indirect access control in the IACR register (0x030 – 0x031) and the indirect
access data registers in IADR4[15:0], IADR5[31:16] (0x02C – 0x02F). The port 1 MIB counters address memory offset
as in Table 4-200.
TABLE 4-200: PORT 1 MIB COUNTERS – INDIRECT MEMORY OFFSET
Offset
Counter Name
Description
0x0
RxLoPriorityByte
Rx lo-priority (default) octet count including bad packets.
0x1
RxHiPriorityByte
Rx hi-priority octet count including bad packets.
0x2
RxUndersizePkt
Rx undersize packets with good CRC.
0x3
RxFragments
0x4
RxOversize
Rx oversize packets with good CRC (maximum: 2000 bytes).
0x5
RxJabbers
Rx packets longer than 1522 bytes with either CRC errors, alignment
errors, or symbol errors (depends on max packet size setting).
0x6
RxSymbolError
0x7
RxCRCError
Rx packets within (64,1522) bytes w/ an integral number of bytes and a
bad CRC (upper limit depends on maximum packet size setting).
0x8
RxAlignmentError
Rx packets within (64,1522) bytes w/ a non-integral number of bytes
and a bad CRC (upper limit depends on maximum packet size setting).
0x9
RxControl8808Pkts
Number of MAC control frames received by a port with 88-08h in EtherType field.
0xA
RxPausePkts
Number of PAUSE frames received by a port. PAUSE frame is qualified
with EtherType (88-08h), DA, control opcode (00-01), data length (64B
minimum), and a valid CRC.
0xB
RxBroadcast
Rx good broadcast packets (not including error broadcast packets or
valid multicast packets).
0xC
RxMulticast
Rx good multicast packets (not including MAC control frames, error
multicast packets or valid broadcast packets).
Rx fragment packets with bad CRC, symbol errors or alignment errors.
Rx packets w/ invalid data symbol and legal packet size.
0xD
RxUnicast
0xE
Rx64Octets
Total Rx packets (bad packets included) that were 64 octets in length.
0xF
Rx65to127Octets
Total Rx packets (bad packets included) that are between 65 and 127
octets in length.
0x10
Rx128to255Octets
Total Rx packets (bad packets included) that are between 128 and 255
octets in length.
DS00002642A-page 182
Rx good unicast packets.
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-200: PORT 1 MIB COUNTERS – INDIRECT MEMORY OFFSET (CONTINUED)
Offset
Counter Name
0x11
Rx256to511Octets
0x12
Rx512to1023Octets
Total Rx packets (bad packets included) that are between 512 and
1023 octets in length.
0x13
Rx1024to2000Octets
Total Rx packets (bad packets included) that are between 1024 and
2000 octets in length (upper limit depends on max packet size setting).
0x14
TxLoPriorityByte
Tx lo-priority good octet count, including PAUSE packets.
0x15
TxHiPriorityByte
Tx hi-priority good octet count, including PAUSE packets.
0x16
TxLateCollision
The number of times a collision is detected later than 512 bit-times into
the Tx of a packet.
0x17
TxPausePkts
0x18
TxBroadcastPkts
Tx good broadcast packets (not including error broadcast or valid multicast packets).
0x19
TxMulticastPkts
Tx good multicast packets (not including error multicast packets or valid
broadcast packets).
0x1A
TxUnicastPkts
Tx good unicast packets.
0x1B
TxDeferred
0x1C
TxTotalCollision
0x1D
TxExcessiveCollision
0x1E
TxSingleCollision
0x1F
TxMultipleCollision
Description
Total Rx packets (bad packets included) that are between 256 and 511
octets in length.
Number of PAUSE frames transmitted by a port.
Tx packets by a port for which the 1st Tx attempt is delayed due to the
busy medium.
Tx total collision, half duplex only.
A count of frames for which Tx fails due to excessive collisions.
Successfully Tx frames on a port for which Tx is inhibited by exactly
one collision.
Successfully Tx frames on a port for which Tx is inhibited by more than
one collision.
TABLE 4-201: "ALL PORTS DROPPED PACKET" MIB COUNTER FORMAT
Bit
Default
R/W
Description
30 - 16
—
N/A
Reserved
15 - 0
0x0000
RO
Counter Value
Note: “All Ports Dropped Packet” MIB Counters do not indicate overflow or validity; therefore, the application must keep
track of overflow and valid conditions.
“All Ports Dropped Packet” MIB counters are read using indirect memory access. The address offsets for these counters
are in Table 4-202.
TABLE 4-202: "ALL PORTS DROPPED PACKET" MIB COUNTERS – INDIRECT MEMORY
OFFSETS
Offset
Counter Name
Description
0x100
Port 1 TX Drop Packets
TX packets dropped due to lack of resources
0x101
Port 2 TX Drop Packets
TX packets dropped due to lack of resources
0x102
Port 3 TX Drop Packets
TX packets dropped due to lack of resources
0x103
Port 1 RX Drop Packets
RX packets dropped due to lack of resources
0x104
Port 2 RX Drop Packets
RX packets dropped due to lack of resources
0x105
Port 3 RX Drop Packets
RX packets dropped due to lack of resources
Examples:
1.
MIB Counter Read (read port 1 “Rx64Octets” counter at indirect address offset 0x0E)
2018 Microchip Technology Inc.
DS00002642A-page 183
KSZ8463ML/RL/FML/FRL
Write to Reg. IACR with 0x1C0E (set indirect address and trigger a read MIB counters operation)
Then:
Read Reg. IADR5 (MIB counter value [31:16]) // If bit [31] = “1”, there was a counter overflow // If bit [30] = “0”, restart
(re-read) from this register
Read Reg. IADR4 (MIB counter value [15:0])
2.
MIB Counter Read (read port 2 “Rx64Octets” counter at indirect address offset 0x2E)
Write to reg. IACR with 0x1C2E (set indirect address and trigger a read MIB counters operation)
Then:
Read Reg. IADR5 (MIB counter value [31:16]) // If bit [31] = “1”, there was a counter overflow // If bit [30] = “0”, restart
(re-read) from this register
Read Reg. IADR4 (MIB counter value [15:0])
3.
MIB Counter Read (read “port 1 TX Drop Packets” counter at indirect address offset 0x100)
Write to Reg. IACR with 0x1D00 (set indirect address and trigger a read MIB counters operation)
Then:
Read Reg. IADR4 (MIB counter value [15:0])
4.4.1
ADDITIONAL MIB INFORMATION
“Per Port” MIB counters are designed as “read clear”. That is, these counters will be cleared after they are read.
“All Ports Dropped Packet” MIB counters are not cleared after they are accessed. The application needs to keep track
of overflow and valid conditions on these counters.
4.5
Static MAC Address Table
The KSZ8463 supports both a static and a dynamic MAC address table. In response to a destination address (DA) look
up, The KSZ8463 searches both tables to make a packet forwarding decision. In response to a source address (SA)
look up, only the dynamic table is searched for aging, migration and learning purposes.
The static DA look up result takes precedence over the dynamic DA look up result. If there is a DA match in both tables,
the result from the static table is used. These entries in the static table will not be aged out by the KSZ8463.
TABLE 4-203: STATIC MAC TABLE FORMAT (8 ENTRIES)
Bit
Default
R/W
Description
57 - 54
0000
RW
FID
Filter VLAN ID - identifies one of the 16 active VLANs.
53
0
RW
Use FID
1 = Specifies the use of FID+MAC for static table look up.
0 = Specifies only the use of MAC for static table look up.
52
0
RW
Override
1 = Overrides the port setting transmit enable = “0” or receive enable =
“0” setting.
0 = Specifies no override.
Note: The override bit also allows usage (turns on the entry) even if the
Valid bit = “0”.
51
0
RW
Valid
1 = Specifies that this entry is valid, and the look up result will be used.
0 = Specifies that this entry is not valid.
DS00002642A-page 184
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 4-203: STATIC MAC TABLE FORMAT (8 ENTRIES) (CONTINUED)
Bit
Default
R/W
Description
50 - 48
000
RW
Forwarding Ports
These 3 bits control the forwarding port(s):
000 = No forward.
001 = Forward to port 1.
010 = Forward to port 2.
100 = Forward to port 3.
011 = Forward to port 1 and port 2.
110 = Forward to port 2 and port 3.
101 = Forward to port 1 and port 3.
111 = Broadcasting (excluding the ingress port).
47 - 0
0
RW
MAC Address
48-bit MAC Address
Static MAC Table Lookup Examples:
• Static Address Table Read (read the second entry at indirect address offset 0x01)
- Write to Reg. IACR with 0x1001 (set indirect address and trigger a read static MAC table operation)
- Then:
- Read Reg. IADR3 (static MAC table bits [57:48])
- Read Reg. IADR2 (static MAC table bits [47:32])
- Read Reg. IADR5 (static MAC table bits [31:16])
- Read Reg. IADR4 (static MAC table bits [15:0])
• Static Address Table Write (write the eighth entry at indirect address offset 0x07)
- Write to Reg. IADR3 (static MAC table bits [57:48])
- Write to Reg. IADR2 (static MAC table bits [47:32])
- Write to Reg. IADR5 (static MAC table bits [31:16])
- Write to Reg. IADR4 (static MAC table bits [15:0])
- Write to Reg. IACR with 0x0007 (set indirect address and trigger a write static MAC table operation)
4.6
Dynamic MAC Address Table
The Dynamic MAC Address is a read-only table.
TABLE 4-204: DYNAMIC MAC ADDRESS TABLE FORMAT (1024 ENTRIES)
Bit
Default
R/W
Description
Data Not Ready
1 = Specifies that the entry is not ready, continue retrying until bit is set to
“0”.
0 = Specifies that the entry is ready.
71
—
RO
70 - 67
—
RO
Reserved
RO
MAC Empty
1 = Specifies that there is no valid entry in the table
0 = Specifies that there are valid entries in the table
66
1
65 - 56
0x000
RO
Number of Valid Entries
Indicates how many valid entries in the table.
0x3FF means 1K entries.
0x001 means 2 entries.
0x000 and bit [66] = “0” means 1 entry.
0x000 and bit [66] = “1” means 0 entry.
55 - 54
—
RO
Time stamp
Specifies the 2-bit counter for internal aging.
2018 Microchip Technology Inc.
DS00002642A-page 185
KSZ8463ML/RL/FML/FRL
TABLE 4-204: DYNAMIC MAC ADDRESS TABLE FORMAT (1024 ENTRIES) (CONTINUED)
Bit
Default
R/W
Description
53 - 52
00
RO
Source Port
Identifies the source port where FID+MAC is learned:
00 = Port 1
01 = Port 2
10 = Port 3
51 - 48
0x0
RO
FID
Specifies the filter ID.
47 - 0
0x0000_0000
_0000
RO
MAC Address
Specifies the 48-bit MAC Address.
Dynamic MAC Address Lookup Example
• Dynamic MAC Address Table Read (read the first entry at indirect address offset 0 and retrieve the MAC table
size)
- Write to Reg. IACR with 0x1800 (set indirect address and trigger a read dynamic MAC Address table operation)
- Then:
- Read Reg. IADR1 (dynamic MAC table bits [71:64]) // If bit [71] = “1”, restart (reread) from this register
- Read Reg. IADR3 (dynamic MAC table bits [63:48])
- Read Reg. IADR2 (dynamic MAC table bits [47:32])
- Read Reg. IADR5 (dynamic MAC table bits [31:16])
- Read Reg. IADR4 (dynamic MAC table bits [15:0])
4.7
VLAN Table
The KSZ8463 uses the VLAN table to perform look-ups. If 802.1Q VLAN mode is enabled (SGCR2[15]), this table will
be used to retrieve the VLAN information that is associated with the ingress packet. This information includes FID (Filter
ID), VID (VLAN ID), and VLAN membership as described in Table 29.
TABLE 4-205: VLAN TABLE FORMAT (16 ENTRIES)
Bit
Default
R/W
Description
19
1
RW
Valid
1 = Specifies that this entry is valid, the look up result will be used.
0 = Specifies that this entry is not valid.
RW
Membership
Specifies which ports are members of the VLAN. If a DA look up fails (no
match in both static and dynamic tables), the packet associated with this
VLAN will be forwarded to ports specified in this field. For example: “101”
means port 3 and port 1 are in this VLAN.
18 - 16
111
15 - 12
0x0
RW
FID
Specifies the Filter ID. The KSZ8463 supports 16 active VLANs represented by these four bit fields. The FID is the mapped ID. If 802.1Q
VLAN is enabled, the look up will be based on FID+DA and FID+SA.
11 - 0
0x001
RW
VID
Specifies the IEEE 802.1Q 12 bits VLAN ID.
If 802.1Q VLAN mode is enabled, then KSZ8463 will assign a VID to every ingress packet. If the packet is untagged or
tagged with a null VID, then the packet is assigned with the default port VID of the ingress port. If the packet is tagged
with non-null VID, then VID in the tag will be used. The look up process will start from the VLAN table look up. If the VID
is not found in any of the VLAN table entries, or if the VID is found but is not valid, then packet will be dropped and no
address learning will take place. If the VID is valid, then FID is retrieved. The FID+DA and FID+SA lookups are performed. The FID+DA look up determines the forwarding ports. If FID+DA fails, then the packet will be broadcast to all
the members (excluding the ingress port) of the VLAN. If FID+SA fails, then the FID+SA will be learned.
DS00002642A-page 186
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
VLAN Table Lookup Examples
1.
VLAN Table Read (read the third entry, at the indirect address offset 0x02)
Write to Reg. IACR with 0x1402 (set indirect address and trigger a read VLAN table operation)
Then:
Read Reg. IADR5 (VLAN table bits [19:16])
Read Reg. IADR4 (VLAN table bits [15:0])
2.
VLAN Table Write (write the seventh entry, at the indirect address offset 0x06)
Write to Reg. IADR5 (VLAN table bits [19:16])
Write to Reg. IADR4 (VLAN table bits [15:0])
Write to Reg. IACR with 0x1406 (set indirect address and trigger a read VLAN table operation)
2018 Microchip Technology Inc.
DS00002642A-page 187
KSZ8463ML/RL/FML/FRL
DS00002642A-page 188
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
5.0
OPERATIONAL CHARACTERISTICS
5.1
Absolute Maximum Ratings*
Supply Voltage (VDD_A3.3, VDD_IO) ........................................................................................................... –0.5V to +5.0V
Supply Voltage (VDD_AL, VDD_L) ............................................................................................................... –0.5V to +1.8V
Input Voltage (All Inputs) ........................................................................................................................... –0.5V to +5.0V
Output Voltage (All Outputs) ..................................................................................................................... –0.5V to +5.0V
Lead Temperature (soldering, 10s) ....................................................................................................................... +260°C
Storage Temperature (TS)...................................................................................................................... –65°C to +150°C
Maximum Junction Temperature (TJ) .................................................................................................................... +125°C
HBM ESD Rating ....................................................................................................................................................... 2 kV
*Exceeding the absolute maximum rating may damage the device. Stresses greater than the absolute maximum rating
may cause permanent damage to the device. Operation of the device at these or any other conditions above those specified in the operating sections of this specification is not implied. Maximum conditions for extended periods may affect
reliability.
5.2
Operating Ratings**
Supply Voltage
VDDA_3.3 ............................................................................................................................................ +3.135V to +3.465V
VDD_L, VDD_AL, VDD_COL......................................................................................................................... +1.25V to +1.4V
VDD_IO (3.3V) .................................................................................................................................... +3.135V to +3.465V
VDD_IO (2.5V) .......................................................................................................................................+2.375 to +2.625V
VDD_IO (1.8V) ........................................................................................................................................ +1.71V to +1.89V
Ambient Operating Temperature (TA)
Industrial .................................................................................................................................................. –40°C to +85°C
Thermal Resistance (Note 5-1)
Junction-to-Ambient (ΘJA)...................................................................................................................................+49°C/W
Junction-to-Case (ΘJC) .......................................................................................................................................+19°C/W
**The device is not guaranteed to function outside its operating ratings. Unused inputs must always be tied to an appropriate logic voltage level (GROUND to VDD_IO).
Note:
Note 5-1
Do not drive input signals without power supplied to the device.
No heat spreader (HS) in this package. The ΘJC/ΘJA is under air velocity 0m/s.
2018 Microchip Technology Inc.
DS00002642A-page 189
KSZ8463ML/RL/FML/FRL
6.0
ELECTRICAL CHARACTERISTICS
TABLE 6-1:
ELECTRICAL CHARACTERISTICS (Note 6-1)
Parameters
Symbol
Min.
Typ.
Max.
Units
Note
Supply Current for 100BASE-TX Operation
(Internal Low-Voltage Regulator On, MII MAC Mode, VDD_A3.3 = 3.3V, VDD_IO = 3.3V) (Note 6-1, Note 6-2)
—
—
—
—
—
—
IVDD_A3.3
—
46
—
mA
IVDD_IO
—
98
—
mA
PDISSDEVICE
—
476
—
mW
IVDD_A3.3
—
4.5
—
mA
IVDD_IO
—
74
—
mA
PDISSDEVICE
—
259
—
mW
IVDD_A3.3
—
5.3
—
mA
IVDD_IO
—
73
—
mA
PDISSDEVICE
—
260
—
mW
IVDD_A3.3
—
5.9
—
mA
IVDD_IO
—
74
—
mA
PDISSDEVICE
—
264
—
mW
IVDD_A3.3
—
1.1
—
mA
IVDD_IO
—
3.2
—
mA
PDISSDEVICE
—
14
—
mW
IVDD_A3.3
—
0.1
—
mA
IVDD_IO
—
1.3
—
mA
PDISSDEVICE
—
4.6
—
mW
100% traffic on both ports
Ports 1 and 2 Powered Down
(P1CR4, P2CR4 bit[11] = “1”)
Ports 1 and 2 Not Connected, using
EDPD Feature
(PMCTRL bits[1:0] = “01”)
Ports 1 and 2 Connected, No Traffic,
using EEE Feature
Soft Power-Down Mode
(PMCTRL bits[1:0] = “10”)
Hardware Power-Down Mode
While the PWDRN pin (pin 17) is Held
Low. (Note 6-3)
Supply Current for 100BASE-TX Operation
(Internal Low-Voltage Regulator Off, MII PHY Mode, VDD_A3.3 and VDD_IO = 3.3V; VDD_L, VDD_AL, and VDD_COL =
1.4V) (Note 6-1, Note 6-2)
—
—
—
—
DS00002642A-page 190
IVDD_A3.3
—
46
—
mA
IVDD_IO
—
21
—
mA
IVDD_AL +
IVDD_DL
—
84
—
mA
PDISSDEVICE
—
328
—
mW
IVDD_A3.3
—
3.8
—
mA
IVDD_IO
—
15.2
—
mA
IVDD_AL +
IVDD_DL
—
71
—
mA
PDISSDEVICE
—
155
—
mW
IVDD_A3.3
—
4.6
—
mA
IVDD_IO
—
15.1
—
mA
IVDD_AL +
IVDD_DL
—
69
—
mA
PDISSDEVICE
—
155
—
mW
IVDD_A3.3
—
5.2
—
mA
IVDD_IO
—
15.4
—
mA
IVDD_AL +
IVDD_DL
—
70
—
mA
PDISSDEVICE
—
159
—
mW
100% Traffic on Both Ports
Ports 1 and 2 Powered Down
(P1CR4, P2CR4 bit[11] = “1”)
Ports 1 and 2 Not Connected, using
EDPD Feature
(PMCTRL bits[1:0] = “01”)
Ports 1 and 2 Connected, No Traffic,
using EEE Feature
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
TABLE 6-1:
ELECTRICAL CHARACTERISTICS (Note 6-1) (CONTINUED)
Parameters
Symbol
Min.
Typ.
Max.
Units
IVDD_A3.3
—
0.1
—
mA
IVDD_IO
—
2.1
—
mA
IVDD_AL +
IVDD_DL
—
1.4
—
mA
PDISSDEVICE
—
9
—
mW
IVDD_A3.3
—
0.1
—
mA
—
IVDD_IO
—
2.1
—
mA
IVDD_AL +
IVDD_DL
—
1.2
—
mA
PDISSDEVICE
—
9
—
mW
—
Note
Soft Power-Down Mode
(PMCTRL bits[1:0] = “10”)
Hardware Power-Down Mode
While the PWDRN pin (pin 17) is Held
Low. (Note 6-3)
Supply Current for 10BASE-T Operation
(Internal Low-Voltage Regulator On, MII MAC Mode, VDD_A3.3 = 3.3V, VDD_IO = 3.3V) (Note 6-1, Note 6-2)
IVDD_A3.3
—
51
—
mA
IVDD_IO
—
78
—
mA
PDISSDEVICE
—
425
—
mW
IVDD_A3.3
—
19.2
—
mA
IVDD_IO
—
72
—
mA
PDISSDEVICE
—
302
—
mW
—
—
100% Traffic on Both Ports
Link, No Traffic on Both Ports
Supply Current for 10BASE-T Operation
(Internal Low-Voltage Regulator Off, MII PHY Mode, VDD_A3.3 and VDD_IO = 3.3V; VDD_L, VDD_AL, and VDD_COL =
1.4V) (Note 6-1, Note 6-2)
IVDD_A3.3
—
50
—
mA
IVDD_IO
—
15.7
—
mA
IVDD_AL +
IVDD_DL
—
71
—
mA
PDISSDEVICE
—
315
—
mW
IVDD_A3.3
—
19
—
mA
IVDD_IO
—
15.3
—
mA
IVDD_AL +
IVDD_DL
—
69
—
mA
PDISSDEVICE
—
212
—
mW
—
1.32
—
V
VDD_IO = 2.5V or 3.3V; internal regulator enabled; measured at pins 40 and
51
—
—
100% Traffic on Both Ports
Link, No Traffic on Both Ports
Internal Voltage Regulator Output Voltage
Output Voltage at VDD_L
VLDO
CMOS Inputs (VDD_IO = 3.3V/2.5V/1.8V)
Input High Voltage
VIH
2.1/1.7/
1.3
—
—
V
—
Input Low Voltage
VIL
—
—
0.9/0.9/
0.6
V
—
Input Current
IIN
–10
—
10
µA
VIN = GND ~ VDD_IO
Input High Voltage
VIH
2.1
—
—
V
VDD_A3.3 = 3.3V, VDD_IO = any
Input Low Voltage
VIL
—
—
0.9
V
VDD_A3.3 = 3.3V, VDD_IO = any
Input Current
IIN
—
—
10
µA
—
VIH
1.1
—
—
V
VDD_A3.3 = 3.3V, VDD_IO = any
X1 Crystal/Osc Input Pin
PWRDN Input (Note 6-3)
Input High Voltage
2018 Microchip Technology Inc.
DS00002642A-page 191
KSZ8463ML/RL/FML/FRL
TABLE 6-1:
ELECTRICAL CHARACTERISTICS (Note 6-1) (CONTINUED)
Parameters
Symbol
Min.
Typ.
Max.
Units
Note
Input Low Voltage
VIL
—
—
0.3
V
VDD_A3.3 = 3.3V, VDD_IO = any
Input High Voltage
VIH
2.1
—
—
V
VDD_A3.3 = 3.3V, VDD_IO = any
Input Low Voltage
VIL
—
—
1.2
V
VDD_A3.3 = 3.3V, VDD_IO = any
FXSD Input
CMOS Outputs (VDD_IO = 3.3V/2.5V/1.8V)
Output High Voltage
VOH
2.4/1.9/
1.5
—
—
V
IOH = –8 mA
Output Low Voltage
VOL
—
—
0.4/0.4/
0.2
V
IOL = 8 mA
Output Tri-State Leakage
|IOZ|
—
—
10
µA
—
100BASE-TX Transmit (Measured Differentially After 1:1 Transformer)
Peak Differential Output
Voltage
VO
±0.95
—
±1.05
V
100Ω termination on the diff. output
Output Voltage Imbalance
VIMB
—
—
2
%
100Ω termination on the diff. output
Rise/Fall Time
tr/tf
3
—
5
ns
—
Rise/Fall Time Imbalance
—
0
—
0.5
ns
—
Duty Cycle Distortion
—
—
—
±0.25
ns
—
Overshoot
—
—
—
5
%
—
Reference Voltage of ISET
VSET
—
0.65
—
V
Using 6.49 kΩ – 1% resistor
Output Jitter
—
—
0.7
1.4
ns
Peak-to-peak
VSQ
—
400
—
mV
5 MHz square wave
10BASE-T Receive
Squelch Threshold
10BASE-T Transmit (Measured Differentially After 1:1 Transformer)
Peak Differential Output
Voltage
VP
2.2
2.5
2.8
V
100Ω termination on the differential
output
Jitter Added
—
—
1.8
3.5
ns
100Ω termination on the differential
output (peak-to-peak)
Rise/Fall Time
tr/tf
—
25
—
ns
—
ILED
—
8
—
mA
Each LED pin (P1/2LED0, P1/2LED1)
LED Outputs
Output Drive Current
I/O Pin Internal Pull-Up and Pull-Down Effective Resistance
1.8V Pull-Up Resistance
R1.8PU
57
100
187
kΩ
1.8V Pull-Down Resistance
R1.8PD
55
100
190
kΩ
2.5V Pull-Up Resistance
R2.5PU
37
59
102
kΩ
2.5V Pull-Down Resistance
R2.5PD
35
60
110
kΩ
3.3V Pull-Up Resistance
R3.3PU
29
43
70
kΩ
3.3V Pull-Down Resistance
R3.3PD
27
43
76
kΩ
Note 6-1
VDD_IO = 1.8V
VDD_IO = 2.5V
VDD_IO = 3.3V
IVDD_A3.3 measured at pin 9. IVDD_IO measured at pins 21, 30, and 56. IVDD_AL measured at pins 6
and 16. IVDD_DL measured at pins 40 and 51.
Note 6-2
TA = 25°C. Specification is for packaged product only.
Note 6-3
For PWRDN pin (pin 17), the operating value of VIH is lower than the other CMOS input pins. It is
not dependent on VDD_IO.
DS00002642A-page 192
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
7.0
TIMING SPECIFICATIONS
7.1
MII Transmit Timing in MAC Mode
FIGURE 7-1:
MII TRANSMIT TIMING IN MAC MODE
tP
tWL
tWH
TX_CLK
(INPUT)
tSU2
TX_EN/TX_ER
(INPUT)
tHD2
tSU1
tHD1
TXD[3:0]
(INPUT)
TABLE 7-1:
MII TRANSMIT TIMING IN MAC MODE PARAMETERS
Symbol
Parameter
Min.
Typ.
Max.
Units
tP (100BASE-TX/10BASET)
RX_CLK Period
—
40/400
—
ns
tWL (100BASE-TX/
10BASE-T)
RX_CLK Pulse Width Low
—
20/200
—
ns
tWH (100BASE-TX/
10BASE-T)
RX_CLK Pulse Width High
—
20/200
—
ns
tOD
RX_DV, RXD[3:0] Output Delay from Rising Edge
of RX_CLK
—
16
—
ns
2018 Microchip Technology Inc.
DS00002642A-page 193
KSZ8463ML/RL/FML/FRL
7.2
MII Receive Timing in MAC Mode
This timing illustrates a read operation by the KSZ8463 from a PHY or other device while operating the KSZ8463 in
MAC mode.
FIGURE 7-2:
MII RECEIVE TIMING IN MAC MODE
RX_DV
(OUTPUT)
tOD
RXD[3:0]
(OUTPUT)
tWL
RX_CLK
(INPUT)
tWH
tP
TABLE 7-2:
MII RECEIVE TIMING IN MAC MODE PARAMETERS
Symbol
Parameter
Min.
Typ.
Max.
Units
tP (100BASE-TX/10BASET)
TX_CLK period
—
40/400
—
ns
tWL (100BASE-TX/
10BASE-T)
TX_CLK pulse width low
—
20/200
—
ns
tWH (100BASE-TX/
10BASE-T)
TX_CLK pulse width high
—
20/200
—
ns
tSU1
TXD[3:0] setup time to rising edge of TX_CLK
10
—
—
ns
tSU2
TX_EN, TX_ER setup time to rising edge of TX_CLK
10
—
—
ns
tHD1
TXD[3:0] hold time from rising edge of TX_CLK
10
—
—
ns
tHD2
TX_EN, TX_ER hold time from rising edge of TX_CLK
10
—
—
ns
DS00002642A-page 194
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
7.3
MII Receive Timing in PHY Mode
FIGURE 7-3:
MII RECEIVE TIMING IN PHY MODE
RX_DV
(OUTPUT)
tOD
RXD[3:0]
(OUTPUT)
tWL
RX_CLK
(OUTPUT)
tWH
tP
TABLE 7-3:
MII RECEIVE TIMING IN PHY MODE PARAMETERS
Parameter
Description
Min.
Typ.
Max.
tP (100BASE-TX/10BASET)
RX_CLK period
—
40/400
—
tWL (100BASE-TX/
10BASE-T)
RX_CLK pulse width low
—
20/200
—
ns
tWH (100BASE-TX/
10BASE-T)
RX_CLK pulse width high
—
20/200
—
ns
tOD
RX_DV, RXD[3:0] output delay from rising edge of
RX_CLK
—
20
—
2018 Microchip Technology Inc.
Units
ns
ns
DS00002642A-page 195
KSZ8463ML/RL/FML/FRL
7.4
MII Transmit Timing in PHY Mode
FIGURE 7-4:
MII TRANSMIT TIMING IN PHY MODE
tP
tWL
tWH
TX_CLK
(OUTPUT)
tSU2
TX_EN/TX_ER
(INPUT)
tHD2
tSU1
tHD1
TXD[3:0]
(INPUT)
TABLE 7-4:
MII TRANSMIT TIMING IN PHY MODE PARAMETERS
Parameter
Description
Min.
Typ.
Max.
Units
tP (100BASE-TX/10BASET)
TX_CLK period
—
40/400
—
ns
tWL (100BASE-TX/
10BASE-T)
TX_CLK pulse width low
—
20/200
—
ns
tWH (100BASE-TX/
10BASE-T)
TX_CLK pulse width high
—
20/200
—
ns
tSU1
TXD[3:0] setup time to rising edge of TX_CLK
10
—
—
ns
tSU2
TX_EN, TX_ER setup time to rising edge of TX_CLK
10
—
—
ns
tHD1
TXD[3:0] hold time from rising edge of TX_CLK
0
—
—
ns
tHD2
TX_EN, TX_ER hold time from rising edge of TX_CLK
0
—
—
ns
DS00002642A-page 196
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
7.5
Reduced MII (RMII) Timing
FIGURE 7-5:
RMII TRANSMIT TIMING
tcyc
REFCLK
t1
t2
TX_EN
TXD[1:0]
(INPUT)
FIGURE 7-6:
RMII RECEIVE TIMING
tcyc
REFCLK
tod
RXD[1:0]
RX_ER
(OUTPUT)
TABLE 7-5:
MII RECEIVE TIMING (100BASE-TX) PARAMETERS
Parameter
Description
Min.
Typ.
Max.
Units
tCYC
Clock cycle
—
20
—
ns
t1
Set-up time
4
—
—
ns
t2
Hold time
2
—
—
ns
tOD
Output delay
7
9
13
ns
2018 Microchip Technology Inc.
DS00002642A-page 197
KSZ8463ML/RL/FML/FRL
7.6
MIIM (MDC/MDIO) Timing
FIGURE 7-7:
MIIM (MDC/MDIO) TIMING
tP
MDC
(INPUT)
tOD
MDIO
(DATA-OUT)
tSU
tHD
MDIO
(DATA-IN)
TABLE 7-6:
MIIM (MDC/MDIO) TIMING PARAMETERS
Parameter Description
Min.
Typ.
Max.
Units
tP
MDC period
—
400
—
ns
tOD
Output delay
—
200
—
ns
tSU
MDIO setup time to rising edge of MDC
2
—
—
ns
tHD
MDIO hold time from rising edge of MDC
5
—
—
ns
DS00002642A-page 198
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
7.7
SPI Input and Output Timing
FIGURE 7-8:
SPI INTERFACE DATA INPUT TIMING
SPI_CSN
t1
1/fSCLK
t4
t5
Typ.
Max.
Units
SPI_SCLK
t2
SPI_DI
t3
MSB BIT
LSB BIT
HIGH IMPEDANCE
SPI_DO
FIGURE 7-9:
SPI INTERFACE DATA OUTPUT TIMING
SPI_CSN
SPI_SCLK
SPI_DO
(LOW-SPEED MODE)
SPI_DO
(HIGH-SPEED MODE)
SPI_DI
TABLE 7-7:
SMII TIMING PARAMETERS
Parameter Description
Min.
fSCLK
SPI_SCLK Clock Frequency
—
—
50
MHz
t1
SPI_CSN active setup time
8
—
—
ns
t2
SPI_DI data input setup time
3
—
—
ns
t3
SPI_DI data input hold time
3
—
—
ns
t4
SPI_CSN active hold time
8
—
—
ns
t5
SPI_CSN disable high time
8
—
—
ns
t6
SPI_SCLK falling edge to SPI_DO data output valid
2
—
9
ns
t7
SPI_CSN inactive to SPI_DO data output invalid
1
—
—
ns
2018 Microchip Technology Inc.
DS00002642A-page 199
KSZ8463ML/RL/FML/FRL
7.8
Auto-Negotiation Timing
FIGURE 7-10:
AUTO-NEGOTIATION TIMING
FLP BURST
FLP BURST
TX+/TXtFLPW
tSTB
DATA PULSE
DATA PULSE
CLOCK PULSE
CLOCK PULSE
TX+/TXtPW
tPW
tCTD
tCTC
TABLE 7-8:
AUTO-NEGOTIATION TIMING PARAMETERS
Parameter Description
tBTB
tFLPW
Min.
Typ.
Max.
Units
FLP Burst to FLP Burst
8
16
24
ms
FLP Burst Width
—
2
—
ms
—
100
—
ns
tPW
Clock/Data Pulse Width
tCTD
Clock Pulse to Data Pulse
55.5
64
69.5
µs
tCTC
Clock Pulse to Clock Pulse
111
128
139
µs
Number of Clock/Data Pulses per FLP Burst
17
—
33
—
—
DS00002642A-page 200
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
7.9
Trigger Output Unit and Time Stamp Input Unit Timing
The timing information in the following figure provides details and constraints on various timing relationships within the
twelve trigger output units and the time stamp input units.
FIGURE 7-11:
TRIGGER OUTPUT UNIT AND TIME STAMP INPUT UNIT TIMING
TRIGGER OUTPUT UNIT TIMING [CASCADE MODE]
TCASP1
TCASP2
TRIGGER UNIT 1
OUTPUT
TRIGGER UNIT 2
OUTPUT
PWIDTH2
TGAP23
TOU2
TOU1
TCYCNC1
PWIDTH2
TCYCCCASP
TRIGGER OUTPUT UNIT TIMING [NON-CASCADE MODE]
TPOGAPH
TPOGAFL
PWIDTH1
TCYCNC2
TIMESTAMP INPUT UNIT TIMING
IPLOW
IPHIGH
IPCYC
2018 Microchip Technology Inc.
DS00002642A-page 201
KSZ8463ML/RL/FML/FRL
TABLE 7-9:
TRIGGER OUTPUT UNIT AND TIME STAMP INPUT UNIT TIMING PARAMETERS
Parameter Description
Min.
Typ.
Max.
Units
TCASP1
In cascade mode for TRIGX_CFG_1[6:4] = 100, or 101, or 110
(Neg. Edge, Pos. Edge, and Shift Reg. Output signals).
Minimum time between start of one TOU and the start of another
TOU cascaded on the same GPIO pin.
80
—
—
ns
TCASP2
In cascade mode for TRIGX_CFG_1[6:4] = 010, 011, 100, or 101
(Neg. Pulse, Pos. Pulse, Neg. Periodic, and Pos. Periodic Output
signals).
Minimum time between start of one TOU and the start of another
TOU cascaded on the same GPIO pin.
120
—
—
ns
TCYCCASP
In cascade mode for TRIGX_CFG_1[6:4] = 010, and 011 (Neg.
Pulse, Pos. Pulse Output signals).
In cascade mode, the cycle time of the trigger output unit operating
in the indicated modes.
80
≥32 + PWIDTH2
ns
TCYCNC1
In cascade mode for TRIGX_CFG_1[6:4] = 100 or 101 (Neg. Periodic, Pos. periodic Output signals).
Minimum cycle time for any trigger output unit operating in the indicated modes.
80
≥32 + PWIDTH2
ns
TGAP23
In cascade mode for TRIGX_CFG_1[6:4] = 010, and 011 (Neg.
Pulse, Pos. Pulse Output signals):
Minimum gap time required between end of period of first trigger
output unit to beginning of output of 2nd trigger output unit.
80
—
—
ns
PWIDTH2
In cascade mode, the minimum low or high pulse width of the trigger output unit.
8
—
—
ns
Trigger Output Unit Timing [Cascade Mode}
Trigger Output Unit Timing [Non-Cascade Mode]
TCYCNC2
In non-cascade mode, the minimum cycle time for any trigger output unit.
80
TPOGAP
In non-cascade mode, the minimum time between the end of the
generated pulse to the start of the next pulse.
32
—
—
ns
PWIDTH1
In non-cascade mode, the minimum low or high pulse width of the
trigger output unit.
8
—
—
ns
≥32 + PWIDTH2
ns
Time Stamp Input Unit Timing
IPHIGH
Allowable high time of an incoming digital waveform on any GPIO
pin
24
—
—
ns
IPLOW
In non-cascade mode, the minimum time between the end of the
generated pulse to the start of the next pulse.
24
—
—
ns
IPCYC
In non-cascade mode, the minimum time between the end of the
generated pulse to the start of the next pulse.
48
—
—
ns
DS00002642A-page 202
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
7.10
Reset and Power Sequence Timing
The KSZ8463 reset timing and power sequence requirements are summarized in the following figure and table.
FIGURE 7-12:
RESET AND POWER SEQUENCE TIMING
NOTE 7-1
TRANSCEIVER (VDD_A3.3), DIGITAL I/Os (VDD_I/O)
NOTE 7-3
CORE (VDD_AL, VDD_L, VDD_COL)
SUPPLY
VOLTAGES
NOTE 7-2
tvr
tpc
tsr
RSTN
tcs
tch
STRAP-IN
VALUE
trc
STRAP-IN/
OUTPUT PIN
TABLE 7-10:
RESET AND POWER SEQUENCE TIMING PARAMETERS
(Note 7-1, Note 7-2, Note 7-3)
Parameter Description
Min.
Typ.
Max.
Units
tVR
Supply voltages rise time (must be monotonic)
0
—
—
µs
tSR
Stable supply voltages to de-assertion of reset
10
—
—
ms
tCS
Strap-in pin configuration setup time
5
—
—
ns
tCH
Strap-in pin configuration hold time
5
—
—
ns
tRC
Note 7-1
De-assertion of reset to strap-in pin output
6
—
—
ns
The recommended powering sequence is to bring up all voltages at the same time. However, if that
cannot be attained, then a recommended power-up sequence is to have the transceiver (VDD_A3.3)
and digital I/Os (VDD_IO) voltages power up before the low voltage core (VDD_AL, VDD_L, and
VDD_COL) voltage, if an external low voltage core supply is used. There is no power sequence
requirement between transceiver (VDD_A3.3) and digital I/Os (VDD_IO) power rails. The power-up
waveforms should be monotonic for all supply voltages to the KSZ8463.
Note 7-2
After the de-assertion of reset, it is recommended to wait a minimum of 100 μs before starting
programming of the device through any interface.
Note 7-3
The recommended power-down sequence is to have the low voltage core voltage power down first
before powering down the transceiver and digital I/O voltages.
2018 Microchip Technology Inc.
DS00002642A-page 203
KSZ8463ML/RL/FML/FRL
7.11
Reset Circuit
The following reset circuit is recommended for powering up the KSZ8463 device if reset is triggered by the power supply.
FIGURE 7-13:
SIMPLE RESET CIRCUIT
VDD_IO
D1: 1N4148
R
10K
D1
KSZ8463
RSTN
RSTN
C
10μF
The following reset circuit is recommended for applications where reset is driven by another device (e.g., CPU or
FPGA). At POR, R, C and D1 provide the necessary ramp rise time to reset the KSZ8463 device. The RST_OUT_N
from CPU/FPGA provides the warm reset after power-up.
FIGURE 7-14:
RECOMMENDED RESET CIRCUIT FOR INTERFACING WITH CPU/FPGA RESET
OUTPUT
VDD_IO
D1
R
10K
KSZ8463
CPU/FPGA
RST_OUT_N
RSTN
D2
C
10μF
D1, D2: 1N4148
DS00002642A-page 204
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
8.0
REFERENCE CLOCK: CONNECTION AND SELECTION
The three different sources for a reference clock are shown in Figure 8-1. Note that MII clocks are not discussed in this
section. The KSZ8463ML and KSZ8463FML require an external 25 MHz crystal attached to X1/X2, or a 25 MHz oscillator attached to X1.
The KSZ8463RL and KSZ8463FRL have two options for a reference clock, as determined by the strapping option on
pin 41. The 25 MHz option on X1/X2 is as described above. When the 50 MHz option is selected, an external 50 MHz
clock is applied to the REFCLK_I pin, while X1 and X2 are unconnected. Note that in the 25 MHz mode, REFCLK_O
must be enabled, and it must be externally connected to REFCLK_I.
The resistor shown on X2 is optional and can be used to limit current to the crystal if needed, depending on the specific
crystal that is used. The maximum recommended value is 30Ω.
FIGURE 8-1:
22pF
INPUT REFERENCE CLOCK CONNECTION OPTIONS
R
25MHz OSC
±50ppm
X1
X1
KSZ8463
(ML/RL/FL)
KSZ8463
(ML/RL/FL)
22pF
X2
N/C
X2
25MHz XTAL
±50ppm
N/C
X1
KSZ8463
(RL)
N/C
50MHz
CLOCK
TABLE 8-1:
X2
RFCLK_I
TYPICAL REFERENCE CRYSTAL CHARACTERISTICS
Characteristics
Value
Frequency
25 MHz
Frequency tolerance (maximum)
±50 ppm
Effective Series resistance (maximum)
50Ω
2018 Microchip Technology Inc.
DS00002642A-page 205
KSZ8463ML/RL/FML/FRL
9.0
SELECTION OF ISOLATION TRANSFORMERS
A 1:1 isolation transformer is required at the line interface. An isolation transformer with integrated common-mode choke
is recommended for exceeding FCC requirements.
Table 9-1 lists recommended transformer characteristics.
TABLE 9-1:
TRANSFORMER SELECTION CRITERIA
Parameter
Value
Test Conditions
Turns Ratio
1 CT:1 CT
—
Open-Circuit Inductance (min.)
350 µH
100 mV, 100 kHz, 8 mA
Leakage Inductance (max.)
0.4 µH
1 MHz (min.)
Interwinding Capacitance (max.)
12 pF
—
D.C. Resistance (max.)
0.9Ω
—
Insertion Loss (max.)
–1.0 dB
100 kHz to 100 MHz
HIPOT (min.)
1500 VRMS
—
TABLE 9-2:
QUALIFIED SINGLE-PORT MAGNETICS
Manufacturer
Part Number
Auto MDI-X
Pulse
H1102NL
Yes
Pulse (low cost)
H1260
Yes
Transpower
HB726
Yes
Bel Fuse
S558-5999-U7
Yes
Delta
LF8505
Yes
LanKom
LF-H41S
Yes
TDK (Mag Jack)
TLA-6T718
Yes
DS00002642A-page 206
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
10.0
PACKAGE OUTLINE
FIGURE 10-1:
Note:
64-LEAD LQFP 10 MM X 10 MM PACKAGE OUTLINE & RECOMMENDED LAND
PATTERN
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging.
2018 Microchip Technology Inc.
DS00002642A-page 207
KSZ8463ML/RL/FML/FRL
APPENDIX A:
TABLE A-1:
DATA SHEET REVISION HISTORY
REVISION HISTORY
Revision
DS00002642A (2-22-18)
DS00002642A-page 208
Section/Figure/Entry
—
Correction
Converted Micrel data sheet KSZ8463ML/RL/FML/
FRL to Microchip DS00002642A. Minor text changes
throughout.
2018 Microchip Technology Inc.
KSZ8463ML/RL/FML/FRL
THE MICROCHIP WEB SITE
Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make
files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information:
• Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s
guides and hardware support documents, latest software releases and archived software
• General Technical Support – Frequently Asked Questions (FAQ), technical support requests, online discussion
groups, Microchip consultant program member listing
• Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives
CUSTOMER CHANGE NOTIFICATION SERVICE
Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive
e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or
development tool of interest.
To register, access the Microchip web site at www.microchip.com. Under “Support”, click on “Customer Change Notification” and follow the registration instructions.
CUSTOMER SUPPORT
Users of Microchip products can receive assistance through several channels:
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales
offices are also available to help customers. A listing of sales offices and locations is included in the back of this document.
Technical support is available through the web site at: http://microchip.com/support
2018 Microchip Technology Inc.
DS00002642A-page 209
KSZ8463ML/RL/FML/FRL
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
Examples:
PART NO.
Device
X
X
X
XX
Interface Package Temperature Media
Type
Device:
KSZ8463
Interface:
M = MII Interface
R = RMII Interface
FM = MII Interface with 100BASE-FX Fiber support
FR = RMII Interface with 100BASE-FX Fiber support
Package:
L = 64-Lead LQFP
Temperature:
I = –40C to +85C (Industrial)
Media Type:
= 160/Tray
DS00002642A-page 210
a) KSZ8463MLI:
b) KSZ8463FMLI:
c) KSZ8463RLI:
d) KSZ8463FRLI:
MII Interface, 64-Lead LQFP,
Industrial Temperature,
160/Tray
MII Interface with 100BASE-FX
Fiber support, 64-Lead LQFP,
Industrial Temperature,
160/Tray
RMII Interface, 64-Lead LQFP,
Industrial Temperature,
160/Tray
RMII Interface with
100BASE-FX Fiber support,
64-Lead LQFP, Industrial
Temperature, 160/Tray
2018 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device applications and the like is provided only for your convenience and may be
superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO
REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE,
MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of
Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, AnyRate, AVR, AVR logo, AVR Freaks, BeaconThings, BitCloud, CryptoMemory, CryptoRF,
dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KEELOQ, KEELOQ logo, Kleer, LANCheck, LINK MD, maXStylus, maXTouch, MediaLB, megaAVR,
MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip Designer, QTouch, RightTouch, SAM-BA, SpyNIC,
SST, SST Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and
other countries.
ClockWorks, The Embedded Control Solutions Company, EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS, mTouch, Precision
Edge, and Quiet-Wire are registered trademarks of Microchip Technology Incorporated in the U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BodyCom, chipKIT, chipKIT logo, CodeGuard,
CryptoAuthentication, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN,
EtherGREEN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, Mindi, MiWi, motorBench,
MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit,
PICtail, PureSilicon, QMatrix, RightTouch logo, REAL ICE, Ripple Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI, SuperSwitcher,
SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.
Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other
countries.
All other trademarks mentioned herein are property of their respective companies.
© 2018, Microchip Technology Incorporated, All Rights Reserved.
ISBN: 978-1-5224-2706-3
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
== ISO/TS 16949 ==
2018 Microchip Technology Inc.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
DS00002642A-page 211
NOTES:
DS00002642A-page 212
2018 Microchip Technology Inc.
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Australia - Sydney
Tel: 61-2-9868-6733
India - Bangalore
Tel: 91-80-3090-4444
China - Beijing
Tel: 86-10-8569-7000
India - New Delhi
Tel: 91-11-4160-8631
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
China - Chengdu
Tel: 86-28-8665-5511
India - Pune
Tel: 91-20-4121-0141
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
China - Chongqing
Tel: 86-23-8980-9588
Japan - Osaka
Tel: 81-6-6152-7160
Finland - Espoo
Tel: 358-9-4520-820
China - Dongguan
Tel: 86-769-8702-9880
Japan - Tokyo
Tel: 81-3-6880- 3770
China - Guangzhou
Tel: 86-20-8755-8029
Korea - Daegu
Tel: 82-53-744-4301
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
China - Hangzhou
Tel: 86-571-8792-8115
Korea - Seoul
Tel: 82-2-554-7200
China - Hong Kong SAR
Tel: 852-2943-5100
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
China - Nanjing
Tel: 86-25-8473-2460
Malaysia - Penang
Tel: 60-4-227-8870
China - Qingdao
Tel: 86-532-8502-7355
Philippines - Manila
Tel: 63-2-634-9065
China - Shanghai
Tel: 86-21-3326-8000
Singapore
Tel: 65-6334-8870
China - Shenyang
Tel: 86-24-2334-2829
Taiwan - Hsin Chu
Tel: 886-3-577-8366
China - Shenzhen
Tel: 86-755-8864-2200
Taiwan - Kaohsiung
Tel: 886-7-213-7830
Israel - Ra’anana
Tel: 972-9-744-7705
China - Suzhou
Tel: 86-186-6233-1526
Taiwan - Taipei
Tel: 886-2-2508-8600
China - Wuhan
Tel: 86-27-5980-5300
Thailand - Bangkok
Tel: 66-2-694-1351
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
China - Xian
Tel: 86-29-8833-7252
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
DS00002642A-page 213
China - Xiamen
Tel: 86-592-2388138
China - Zhuhai
Tel: 86-756-3210040
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-67-3636
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Italy - Padova
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-7289-7561
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
2018 Microchip Technology Inc.
10/25/17