10.7 Gbps Active Back-Termination,
Differential Laser Diode Driver
ADN2525
Data Sheet
FEATURES
GENERAL DESCRIPTION
Up to 10.7 Gbps operation
Very low power: 670 mW (IBIAS = 40 mA, IMOD = 40 mA)
Typical 24 ps rise/fall times
Full back-termination of output transmission lines
Compatible with XMD-MSA TOSA
Drives TOSAs with resistances ranging from 5 Ω to 50 Ω
PECL-/CML-compatible data inputs
Bias current range: 10 mA to 100 mA
Differential modulation current range: 10 mA to 80 mA
Automatic laser shutdown (ALS)
3.3 V operation
Compact 3 mm × 3 mm LFCSP
Voltage input control for bias and modulation currents
XFP-compliant bias current monitor
Optical evaluation board available
The ADN2525 laser diode driver is designed for direct modulation of packaged laser diodes having a differential resistance
ranging from 5 Ω to 50 Ω. The active back-termination technique
provides excellent matching with the output transmission lines
while reducing the power dissipation in the output stage. The
back-termination in the ADN2525 absorbs signal reflections
from the TOSA end of the output transmission lines, enabling
excellent optical eye quality to be achieved even when the
TOSA end of the output transmission lines is significantly
misterminated. The small package provides the optimum
solution for compact modules where laser diodes are packaged
in low pin-count optical subassemblies.
The modulation and bias currents are programmable via the
MSET and BSET control pins. By driving these pins with
control voltages, the user has the flexibility to implement
various average power and extinction ratio control schemes,
including closed-loop control and look-up tables. The automatic
laser shutdown (ALS) feature allows the user to turn on/off the
bias and modulation currents by driving the ALS pin with the
proper logic levels.
APPLICATIONS
SONET OC-192 optical transceivers
SDH STM-64 optical transceivers
10 Gb Ethernet optical transceivers
XFP/X2/XENPAK/XPAK/MSA 300 optical modules
SR and VSR optical links
The product is available in a space-saving 3 mm × 3 mm LFCSP
specified from −40°C to +85°C.
FUNCTIONAL BLOCK DIAGRAM
VCC
ALS
VCC
ADN2525
VCC
50Ω
IMODP
50Ω
50Ω
GND
IMOD
IMODN
VCC
DATAP
DATAN
IBMON
IBIAS
800Ω
800Ω
200Ω
GND
BSET
200Ω
2Ω
05077-001
MSET
200Ω
Figure 1.
Rev. B
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2005–2017 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADN2525
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Bias Current ...................................................................................9
Applications ....................................................................................... 1
Automatic Laser Shutdown (ALS) ........................................... 10
General Description ......................................................................... 1
Modulation Current ................................................................... 10
Functional Block Diagram .............................................................. 1
Load Mistermination ................................................................. 12
Revision History ............................................................................... 2
Power Consumption .................................................................. 12
Specifications..................................................................................... 3
Applications Information .............................................................. 13
Thermal Specifications ................................................................ 4
Typical Application Circuit ....................................................... 13
Absolute Maximum Ratings ............................................................ 5
Layout Guidelines....................................................................... 13
ESD Caution .................................................................................. 5
Design Example .......................................................................... 14
Pin Configuration and Function Descriptions ............................. 6
Outline Dimensions ....................................................................... 15
Typical Performance Characteristics ............................................. 7
Ordering Guide .......................................................................... 15
Theory of Operation ........................................................................ 9
Input Stage ..................................................................................... 9
REVISION HISTORY
4/2017—Rev. A to Rev. B
Changed CP-16-3 to CP-16-22 .................................... Throughout
Updated Outline Dimensions ....................................................... 15
Changes to Ordering Guide .......................................................... 15
8/2006—Rev. 0 to Rev. A
Changes to Format ............................................................. Universal
Changes to Features and Figure 1................................................... 1
Changes to Table 1 ............................................................................ 3
Changes to Table 3 ............................................................................ 5
Changes to Figure 19 ........................................................................ 9
Changes to Figure 25 ...................................................................... 10
Changes to Modulation Current Section and Figure 29 ........... 11
Changes to Typical Application Circuit Section......................... 13
Changes to Ordering Guide .......................................................... 15
3/2005—Revision 0: Initial Version
Rev. B | Page 2 of 16
Data Sheet
ADN2525
SPECIFICATIONS
VCC = VCCMIN to VCCMAX, TA = −40°C to +85°C, 50 Ω differential load resistance, unless otherwise noted. Typical values are specified at
25°C, IMOD = 40 mA.
Table 1.
Parameter
BIAS CURRENT (IBIAS)
Bias Current Range
Bias Current while ALS Asserted
Compliance Voltage 1
MODULATION CURRENT (IMODP, IMODN)
Modulation Current Range
Modulation Current While ALS Asserted
Rise Time (20% to 80%) 2, 3
Fall Time (20% to 80%)2, 3
Random Jitter2, 3
Deterministic Jitter3, 4
Pulse-Width Distortion2, 3
Differential |S22|
Compliance Voltage1
DATA INPUTS (DATAP, DATAN)
Input Data Rate
Differential Input Swing
Differential |S11|
Input Termination Resistance
BIAS CONTROL INPUT (BSET)
BSET Voltage to IBIAS Gain
BSET Input Resistance
MODULATION CONTROL INPUT (MSET)
MSET Voltage to IMOD Gain
MSET Input Resistance
BIAS MONITOR (IBMON)
IBMON to IBIAS Ratio
Accuracy of IBIAS to IBMON Ratio
AUTOMATIC LASER SHUTDOWN (ALS)
VIH
VIL
IIL
IIH
ALS Assert Time
Min
Typ
10
0.6
0.6
10
24
24
0.4
7.2
2
−10
−14
Unit
Test Conditions/Comments
100
100
VCC – 1.2
VCC – 0.8
mA
µA
V
V
ALS = high
IBIAS = 100 mA
IBIAS = 10 mA
80
0.5
32.5
32.5
0.9
12
5
mA diff
mA diff
ps
ps
ps rms
ps p-p
ps
dB
dB
V
VCC − 1.1
VCC + 1.1
0.4
10.7
1.6
85
−16.8
100
115
Gbps
V p-p diff
dB
Ω
75
800
100
1000
120
1200
mA/V
Ω
70
800
88
1000
110
1200
mA/V
Ω
+5.0
+4.0
+2.5
+2
µA/mA
%
%
%
%
0.8
+20
200
2
V
V
µA
µA
µs
10
µs
3.53
45
176
V
mA
mA
10
−5.0
−4.0
−2.5
−2
2.4
−20
0
ALS Negate Time
POWER SUPPLY
VCC
ICC 5
ISUPPLY 6
Max
3.07
3.3
39
157
See notes on next page.
Rev. B | Page 3 of 16
RLOAD = 5 Ω to 50 Ω differential
ALS = high
Includes pulse-width distortion
PWD = ABS(THIGH − TLOW)/2
5 GHz < f < 10 GHz, Z0 = 50 Ω differential
f < 5 GHz, Z0 = 50 Ω differential
NRZ
Differential ac-coupled
f < 10 GHz, Z0 = 100 Ω differential
Differential
See Figure 29
10 mA ≤ IBIAS < 20 mA, RIBMON = 1 kΩ
20 mA ≤ IBIAS < 40 mA, RIBMON = 1 kΩ
40 mA ≤ IBIAS < 70 mA, RIBMON = 1 kΩ
70 mA ≤ IBIAS < 100 mA, RIBMON = 1 kΩ
Rising edge of ALS to fall of IBIAS and
IMOD below 10% of nominal; see Figure 2
Falling edge of ALS to rise of IBIAS and
IMOD above 90% of nominal; see Figure 2
VBSET = VMSET = 0 V
VBSET = VMSET = 0 V; ISUPPLY = ICC + IMODP + IMODN
ADN2525
Data Sheet
1
Refers to the voltage between the pin for which the compliance voltage is specified and GND.
The pattern used is composed by a repetitive sequence of eight 1s followed by eight 0s at 10.7 Gbps.
3
Measured using the high speed characterization circuit shown in Figure 3.
4
The pattern used is K28.5 (00111110101100000101) at a 10.7 Gbps rate.
5
Only includes current in the ADN2525 VCC pins.
6
Includes current in ADN2525 VCC pins and dc current in IMODP and IMODN pull-up inductors. See the Power Consumption section for total supply current calculation.
2
THERMAL SPECIFICATIONS
Table 2.
Parameter
θJ-PAD
θJ-TOP
IC Junction Temperature
Min
2.6
65
Typ
5.8
72.2
Max
10.7
79.4
125
Unit
°C/W
°C/W
°C
Conditions/Comments
Thermal resistance from junction to bottom of exposed pad
Thermal resistance from junction to top of package
ALS
NEGATE TIME
ALS
t
IBIAS
AND IMOD
90%
10%
05077-002
t
ALS
ASSERT TIME
Figure 2. ALS Timing Diagram
VEE
VEE
VEE
GND
10Ω
1kΩ
VBSET
TP1
10nF
TP2
GND
VCC
VCC
GND
GND
ADN2525
Z0 = 50Ω 10nF Z0 = 50Ω
J2
GND
Z0 = 25Ω
J3
IMODN
DATAN
GND
GND
Z0 = 25Ω
IMODP
DATAP
GND
GND
GND
Z0 = 50Ω 10nF Z0 = 50Ω
GND
GND
35Ω
GND
VCC
MSET
VCC
NC1
ALS
VMSET
GND
10nF
VEE
VEE
J8
GND
J5
GND
GND
GND
GND
VEE
GND
50Ω
ADAPTER
ATTENUATOR
ADAPTER
ATTENUATOR
GND
OSCILLOSCOPE
70Ω
Z = 50Ω
35Ω 0
GND
GND
Z0 = 50Ω
BIAS
TEE
BIAS
TEE
50Ω
GND
GND
BIAS TEE: PICOSECOND PULSE LABS MODEL 5542-219
ADAPTER: PASTERNACK PE-9436 2.92mm FEMALE-TO-FEMALE ADAPTER
ATTENUATOR: PASTERNACK PE-7046 2.92mm 20dB ATTENUATOR
22µF
GND
Figure 3. High Speed Characterization Circuit
Rev. B | Page 4 of 16
05077-003
BSET IBMON IBIAS
Data Sheet
ADN2525
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
Supply Voltage, VCC to GND
IMODP, IMODN to GND
DATAP, DATAN to GND
All Other Pins
Junction Temperature
Storage Temperature Range
Soldering Temperature
(Less than 10 sec)
Min
−0.3
VCC − 1 .5
VCC − 1.8
−0.3
−65
Max
+4.2
4.75
VCC − 0.4
VCC + 0.3
150
+150
300
Unit
V
V
V
V
°C
°C
°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
ESD CAUTION
Rev. B | Page 5 of 16
ADN2525
Data Sheet
13 VCC
14 DATAP
16 VCC
12 BSET
MSET 1
NC 2
ADN2525
ALS 3
TOP VIEW
(Not to Scale)
11 IBMON
10 IBIAS
9
GND
VCC 8
IMODP 7
VCC 5
IMODN 6
GND 4
05077-016
PIN 1
INDICATOR
15 DATAN
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 4. Pin Configuration
Note that the exposed pad on the bottom of the package must be connected to the VCC or GND plane.
Table 4. Pin Function Description
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Exposed Pad
Mnemonic
MSET
NC
ALS
GND
VCC
IMODN
IMODP
VCC
GND
IBIAS
IBMON
BSET
VCC
DATAP
DATAN
VCC
Pad
I/O
Input
N/A
Input
Power
Power
Output
Output
Power
Power
Output
Output
Input
Power
Input
Input
Power
Power
Description
Modulation Current Control Input
No Connect—Leave Floating
Automatic Laser Shutdown
Negative Power Supply
Positive Power Supply
Modulation Current Negative Output
Modulation Current Positive Output
Positive Power Supply
Negative Power Supply
Bias Current Output
Bias Current Monitoring Output
Bias Current Control Input
Positive Power Supply
Data Signal Positive Input
Data Signal Negative Input
Positive Power Supply
Connect to GND or VCC
Rev. B | Page 6 of 16
Data Sheet
ADN2525
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, VCC = 3.3 V, unless otherwise noted.
28.0
9
27.5
8
DETERMINISTIC JITTER (ps p-p)
27.0
26.0
25.5
25.0
24.5
24.0
6
5
4
3
2
20
40
60
80
DIFFERENTIAL MODULATION CURRENT (mA)
100
0
05077-004
0
0
20
40
60
80
DIFFERENTIAL MODULATION CURRENT (mA)
Figure 5. Rise Time vs. IMOD
Figure 8. Deterministic Jitter vs. IMOD
27.5
350
TOTAL SUPPLY CURRENT (mA)
26.0
FALL TIME (ps)
IBIAS = 100mA
300
26.5
25.5
25.0
24.5
24.0
23.5
20
40
60
80
DIFFERENTIAL MODULATION CURRENT (mA)
100
IBIAS = 10mA
200
150
100
50
0
05077-005
0
IBIAS = 50mA
250
0
20
40
60
80
DIFFERENTIAL MODULATION CURRENT (mA)
Figure 9. Total Supply Current vs. IMOD
0.7
0
0.6
–5
–10
DIFFERENTIAL |S11| (dB)
0.5
0.4
0.3
0.2
0.1
0
–15
–20
–25
–30
–35
0
20
40
60
80
DIFFERENTIAL MODULATION CURRENT (mA)
100
–40
05077-006
RANDOM JITTER (ps rms)
Figure 6. Fall Time vs. IMOD
100
05077-008
27.0
23.0
100
05077-007
1
23.5
23.0
7
0
Figure 7. Random Jitter vs. IMOD
1
2
3
4
5
6 7 8 9 10 11 12 13 14 15
FREQUENCY (GHz)
Figure 10. Differential |S11|
Rev. B | Page 7 of 16
05077-009
RISE TIME (ps)
26.5
ADN2525
Data Sheet
(ACQ LIMIT TEST) WAVEFORMS: 1000
0
DIFFERENTIAL |S22| (dB)
–5
–10
–15
–20
–25
–30
0
1
2
3
4
5
6 7 8 9 10 11 12 13 14 15
FREQUENCY (GHz)
05077-010
–40
05077-013
–35
Figure 11. Differential |S22|
Figure 14. Electrical Eye Diagram
(10.7 Gbps, PRBS31, IMOD = 80 mA)
16
14
% OCCURRENCE
12
10
8
6
4
23
24
25
26
27
RISE TIME (ps)
28
29
30
05077-014
0
05077-011
2
Figure 15. Filtered SONET OC192 Optical Eye Diagram (for Reference)
(PRBS31 Pattern, PAV = −2 dBm, ER = 7 dB,
17% Mask Margin, NEC NX8341UJ TOSA)
Figure 12. Worst-Case Rise Time Distribution
(VCC = 3.07 V, IBIAS = 100 mA, IMOD = 80 mA, TA = 85°C)
16
14
10
8
6
4
2
23
24
25
26
27
FALL TIME (ps)
28
29
30
05077-015
0
05077-012
% OCCURRENCE
12
Figure 13. Worst-Case Fall Time Distribution
(VCC = 3.07 V, IBIAS = 100 mA, IMOD = 80 mA, TA = 85°C)
Figure 16. Filtered 10G Ethernet Optical Eye
(PRBS31 Pattern, PAV = −2 dBm, ER = 5 dB,
41% Mask Margin, NEC NX8341UJ TOSA)
Rev. B | Page 8 of 16
Data Sheet
ADN2525
THEORY OF OPERATION
The ADN2525 input stage must be ac-coupled to the signal
source to eliminate the need for matching between the commonmode voltages of the data signal source and the input stage of
the driver (see Figure 18). The ac-coupling capacitors should
have an impedance less than 50 Ω over the required frequency
range. Generally, this is achieved using 10 nF to 100 nF capacitors.
50Ω
50Ω
ADN2525
C
DATAP
DATAN
C
05077-018
As shown in Figure 1, the ADN2525 consists of an input stage
and two voltage-controlled current sources for bias and
modulation. The bias current is available at the IBIAS pin. It is
controlled by the voltage at the BSET pin and can be monitored
at the IBMON pin. The differential modulation current is
available at the IMODP and IMODN pins. It is controlled by
the voltage at the MSET pin. The output stage implements the
active back-match circuitry for proper transmission line
matching and power consumption reduction. The ADN2525
can drive a load having differential resistance ranging from 5 Ω
to 50 Ω. The excellent back-termination in the ADN2525
absorbs signal reflections from the TOSA end of the output
transmission lines, enabling excellent optical eye quality to be
achieved even when the TOSA end of the output transmission
lines is significantly misterminated.
DATA SIGNAL SOURCE
Figure 18. AC-Coupling the Data Source to the ADN2525 Data Inputs
INPUT STAGE
The input stage of the ADN2525 converts the data signal applied
to the DATAP and DATAN pins to a level that ensures proper
operation of the high speed switch. The equivalent circuit of the
input stage is shown in Figure 17.
BIAS CURRENT
The bias current is generated internally using a voltage-to-current
converter consisting of an internal operational amplifier and a
transistor, as shown in Figure 19.
VCC
VCC
ADN2525
R
R
DATAP
50Ω
IBMON
VCC
BSET
IBMON
800Ω
IBIAS
IBIAS
VCC
200Ω
200Ω
05077-017
DATAN
GND
2Ω
05077-019
50Ω
Figure 17. Equivalent Circuit of the Input Stage
Figure 19. Voltage-to-Current Converter Used to Generate IBIAS
The DATAP and DATAN pins are terminated internally with a
100 Ω differential termination resistor. This minimizes signal
reflections at the input, which could otherwise lead to degradation
in the output eye diagram. It is not recommended to drive the
ADN2525 with single-ended data signal sources.
The voltage-to-current conversion factor is set at 100 mA/V by
the internal resistors, and the bias current is monitored using a
current mirror with a gain equal to 1/100. By connecting a 1 kΩ
resistor between IBMON and GND, the bias current can be
monitored as a voltage across the resistor. A low temperature
coefficient precision resistor must be used for the IBMON
resistor (RIBMON). Any error in the value of RIBMON due to
tolerances, or drift in its value over temperature, contributes to
the overall error budget for the IBIAS monitor voltage. If the
IBMON voltage is being connected to an ADC for A/D
conversion, RIBMON should be placed close to the ADC to
minimize errors due to voltage drops on the ground plane.
Rev. B | Page 9 of 16
ADN2525
Data Sheet
The equivalent circuits of the BSET, IBIAS, and IBMON pins
are shown in Figure 20, Figure 21, and Figure 22.
VCC
VCC
AUTOMATIC LASER SHUTDOWN (ALS)
BSET
The ALS pin is a digital input that enables/disables both the bias
and modulation currents, depending on the logic state applied,
as shown in Table 5.
800Ω
05077-020
200Ω
Table 5.
Figure 20. Equivalent Circuit of the BSET Pin
IBIAS
ALS Logic State
High
Low
Floating
VCC
VCC
The function of the inductor L is to isolate the capacitance of
the IBIAS output from the high frequency signal path. For
recommended components, see Table 6.
2kΩ
IBIAS and IMOD
Disabled
Enabled
Enabled
100Ω
The ALS pin is compatible with 3.3 V CMOS and TTL logic
levels. Its equivalent circuit is shown in Figure 24.
05077-021
VCC
Figure 21. Equivalent Circuit of the IBIAS Pin
VCC
VCC
VCC
100Ω
ALS
50kΩ
500Ω
05077-024
2Ω
2kΩ
Figure 24. Equivalent Circuit of the ALS Pin
MODULATION CURRENT
100Ω
IBMON
05077-022
VCC
Figure 22. Equivalent Circuit of the IBMON Pin
The recommended configuration for BSET, IBIAS, and IBMON
is shown in Figure 23.
The modulation current can be controlled by applying a dc
voltage to the MSET pin. This voltage is converted into a dc
current by using a voltage-to-current converter using an
operational amplifier and a bipolar transistor, as shown in
Figure 25.
VCC
TO LASER CATHODE
L
IMODP
IBIAS
50Ω
IBIAS
IMOD
IMODN
ADN2525
BSET
GND
MSET
RIBMON
1kΩ
800Ω
05077-023
VBSET
FROM INPUT STAGE
IBMON
The circuit used to drive the BSET voltage must be able to drive
the 1 kΩ input resistance of the BSET pin. For proper operation
of the bias current source, the voltage at the IBIAS pin must be
between the compliance voltage specifications for this pin over
supply, temperature, and bias current range (see Table 1). The
maximum compliance voltage is specified for only two bias
current levels (10 mA and 100 mA), but it can be calculated for
any bias current by
VCOMPLIANCE_MAX (V) = VCC (V) − 0.75 − 4.4 × IBIAS (A)
See the Applications Information section for examples of
headroom calculations.
200Ω
ADN2525
GND
Figure 25. Generation of Modulation Current on the ADN2525
This dc current is switched by the data signal applied to the
input stage (DATAP and DATAN pins) and gained up by the
output stage to generate the differential modulation current at
the IMODP and IMODN pins.
The output stage also generates the active back-termination,
which provides proper transmission line termination. Active
back-termination uses feedback around an active circuit to
synthesize a broadband termination resistance. This provides
Rev. B | Page 10 of 16
05077-025
Figure 23. Recommended Configuration for the BSET, IBIAS, and IBMON Pins
Data Sheet
ADN2525
210
200
190
180
170
VCC
MSET
800Ω
MAXIMUM
150
140
TYPICAL
130
120
MINIMUM
110
100
05077-026
200Ω
160
90
80
Figure 26. Equivalent Circuit of the MSET Pin
70
60
0
VCC
IMODN
VCC
IMODP
Figure 27. Equivalent Circuit of the IMODP and IMODN Pins
VCC
ADN2525
L
Z0 = 25Ω
L
C
Z0 = 25Ω
C
Z0 = 25Ω
IMODP
TOSA
Z0 = 25Ω
VMSET
IMODN
GND
L
L
VCC VCC
05077-028
MSET
50
55
The circuit used to drive the MSET voltage must be able to
drive the 1 kΩ resistance of the MSET pin. To be able to drive
80 mA modulation currents through the differential load, the
output stage of the ADN2525 (the IMODP and IMODN pins)
must be ac-coupled to the load. The voltages at these pins have
a dc component equal to VCC and an ac component with
single-ended, peak-to-peak amplitude of IMOD × 25 Ω. This is
the case even if the load impedance is less than 50 Ω differential,
because the transmission line characteristic impedance sets the
peak-to-peak amplitude. For proper operation of the output stage,
the voltages at the IMODP and IMODN pins must be between
the compliance voltage specifications for this pin over supply,
temperature, and modulation current range, as shown in Figure 30.
See the Applications Information section for examples of
headroom calculations.
The recommended configuration of the MSET, IMODP,
and IMODN pins is shown in Figure 28. See Table 6 for
recommended components.
IBIAS
35
40
45
15
20
25
30
DIFFERENTIAL LOAD RESISTANCE
Using the resistance of the TOSA, the user can calculate the
voltage range that should be applied to the MSET pin to generate
the required modulation current range (see the example in the
Applications Information section).
3.3Ω
05077-027
3.3Ω
10
Figure 29. MSET Voltage-to-Modulation Current Ratio vs.
Differential Load Resistance
25Ω
25Ω
5
05077-029
VCC
The ratio between the voltage applied to the MSET pin and the
differential modulation current available at the IMODP and
IMODN pins is a function of the load resistance value, as shown
in Figure 29.
IMOD/VMSET (mA/V)
excellent transmission line termination, while dissipating less
power than a traditional resistor passive back-termination. No
portion of the modulation current flows in the active backtermination resistance. All of the preset modulation current
IMOD, the range specified in Table 1, flows in the external load.
The equivalent circuits for MSET, IMODP, and IMODN are
shown in Figure 26 and Figure 27. The two 25 Ω resistors in
Figure 27 are not real resistors; they represent the active backtermination resistance.
Figure 28. Recommended Configuration for the MSET, IMODP, and IMODN Pins
Rev. B | Page 11 of 16
ADN2525
Data Sheet
IMODP, IMODN
Table 2. For improved heat dissipation, the module’s case can be
used as heat sink, as shown in Figure 31. A compact optical
module is a complex thermal environment, and calculations of
device junction temperature using the package θJA (junction-toambient thermal resistance) do not yield accurate results.
VCC + 1.1V
THERMAL COMPOUND
NORMAL OPERATION REGION
MODULE CASE
VCC
TTOP
VCC – 1.1V
DIE
TJ
THERMOCOUPLE
PACKAGE
05077-030
T PAD
PCB
05077-031
Figure 30. Allowable Range for the Voltage at IMODP and IMODN
COPPER PLANE
VIAS
LOAD MISTERMINATION
Figure 31. Typical Optical Module Structure
Due to its excellent S22 performance, the ADN2525 can drive
differential loads that range from 5 Ω to 50 Ω. In practice, many
TOSAs have differential resistance less than 50 Ω. In this case,
with 50 Ω differential transmission lines connecting the
ADN2525 to the load, the load end of the transmission lines are
misterminated. This mistermination leads to signal reflections
back to the driver. The excellent back-termination in the
ADN2525 absorbs these reflections, preventing their reflection
back to the load. This enables excellent optical eye quality to be
achieved, even when the load end of the transmission lines is
significantly misterminated. The connection between the load
and the ADN2525 must be made with 50 Ω differential (25 Ω
single-ended) transmission lines so that the driver end of the
transmission lines is properly terminated.
The following procedure can be used to estimate the IC
junction temperature:
TTOP is the temperature at top of package in °C.
TPAD is the temperature at package exposed paddle in °C.
TJ is the IC junction temperature in °C.
P is the power dissipation in W.
θJ-TOP is the thermal resistance from IC junction to package
top.
θJ-PAD is the thermal resistance from IC junction to package
exposed pad.
TTOP
POWER CONSUMPTION
θJ-TOP
TTOP
The power dissipated by the ADN2525 is given by
V
P VCC MSET I SUPPLY VIBIAS IBIAS
13.5
θJ-PAD
P
TPAD
VCC is the power supply voltage.
05077-032
TPAD
where:
Figure 32. Electrical Model for Thermal Calculations
IBIAS is the bias current generated by the ADN2525.
TTOP and TPAD can be determined by measuring the temperature
at points inside the module, as shown in Figure 31. The thermocouples should be positioned to obtain an accurate measurement
of the package top and paddle temperatures. Using the model
shown in Figure 32, the junction temperature can be calculated by
VMSET is the voltage applied to the MSET pin.
ISUPPLY is the sum of the current that flows into the VCC,
IMODP, and IMODN pins of the ADN2525 when
IBIAS = IMOD = 0 expressed in amps (see Table 1).
VIBIAS is the average voltage on the IBIAS pin.
TJ
Considering VBSET/IBIAS = 10 as the conversion factor from
VBSET to IBIAS, the dissipated power becomes
P J PAD J TOP TTOP J PAD TPAD J TOP
J PAD J TOP
where:
V
V
P VCC MSET I SUPPLY BSET VIBIAS
10
13.5
θJ-TOP and θJ-PAD are given in Table 2.
P is the power dissipated by the ADN2525.
To ensure long-term reliable operation, the junction temperature of the ADN2525 must not exceed 125°C, as specified in
Rev. B | Page 12 of 16
Data Sheet
ADN2525
APPLICATIONS INFORMATION
TYPICAL APPLICATION CIRCUIT
LAYOUT GUIDELINES
Figure 33 shows the typical application circuit for the ADN2525.
The dc voltages applied to the BSET and MSET pins control the
bias and modulation currents. The bias current can be monitored
as a voltage drop across the 1 kΩ resistor connected between
the IBMON pin and GND. The ALS pin allows the user to turn
on/off the bias and modulation currents, depending on the logic
level applied to the pin. The data signal source must be connected
to the DATAP and DATAN pins of the ADN2525 using 50 Ω
transmission lines. The modulation current outputs, IMODP
and IMODN, must be connected to the load (TOSA) using 50 Ω
differential (25 Ω single-ended) transmission lines. Table 6
shows recommended components for the ac-coupling interface
between the ADN2525 and TOSA. For up-to-date component
recommendations, contact sales.
Due to the high frequencies at which the ADN2525 operates,
care should be taken when designing the PCB layout to obtain
optimum performance. Controlled impedance transmission
lines must be used for the high speed signal paths. The length of
the transmission lines must be kept to a minimum to reduce
losses and pattern-dependent jitter. The PCB layout must be
symmetrical, both on the DATAP and DATAN inputs and on
the IMODP and IMODN outputs, to ensure a balance between
the differential signals. All VCC and GND pins must be connected
to solid copper planes by using low inductance connections.
When the connections are made through vias, multiple vias
can be connected in parallel to reduce the parasitic inductance.
Each GND pin must be locally decoupled with high quality
capacitors. If proper decoupling cannot be achieved using a
single capacitor, the user can use multiple capacitors in parallel
for each GND pin. A 20 µF tantalum capacitor must be used as a
general decoupling capacitor for the entire module. For guidelines
on the surface-mount assembly of the ADN2525, see Amkor
Technology® Application Notes for Surface Mount Assembly of
Amkor’s MicroLeadFrame® (MLF) Packages.
Working with a TOSA laser sample, the circuit in Figure 33 delivers
the optical performance shown in Figure 15 and Figure 16. For
additional applications information and optical eye performance of
other laser samples, contact ADI sales or see the ADN2525
application notes at www.analog.com.
Table 6.
Value
36 Ω
200 Ω
100 nF
L2, L3, L6, L7
82 nH
L1, L4, L5, L8
10 µH
Description
0603 size resistor
0603 size resistor
0603 size capacitor,
Phycomp 223878615649
0402 size inductor,
Murata LQW15AN82NJ0
0603 size inductor,
Murata LQM21FN100M70L
VCC
GND
BSET
R5
1kΩ
GND
C5
10nF
TP1
L1
R1
L8
R4
VCC
VCC
BSET IBMON IBIAS GND
VCC
VCC
Z0 = 50Ω
VCC
L2
L7
Z0 = 25Ω
DATAP
DATAP
DATAN
DATAN
Z0 = 25Ω
VCC
MSET NC1
Z0 = 25Ω
TOSA
IMODN
C2
VCC
C4
GND
ADN2525
Z0 = 50Ω
Z0 = 25Ω
IMODP
C1
ALS
VCC
GND
GND
L3
C3
L6
VCC
VCC
C6
10nF
MSET
3.3V
VCC
C7
200µF
GND
ALS
L4
R2
L5
R3
GND
VCC
Figure 33. Typical ADN2525 Application Circuit
Rev. B | Page 13 of 16
VCC
05077-033
Component
R1, R2
R3, R4
C3, C4
ADN2525
Data Sheet
DESIGN EXAMPLE
This design example covers:
•
•
Headroom calculations for IBIAS, IMODP, and IMODN
pins.
Calculation of the typical voltage required at the BSET and
MSET pins to produce the desired bias and modulation
currents.
This design example assumes that the resistance of the TOSA is
25 Ω, the forward voltage of the laser at low current is VF = 1 V,
IBIAS = 40 mA, IMOD = 60 mA, and VCC = 3.3 V.
voltage at each modulation output pin should be within the
normal operation region shown in Figure 30.
Assuming VLB = 0 V and IMOD = 60 mA, the minimum voltage
at the modulation output pins is equal to
VCC − (IMOD × 25)/2 = VCC − 0.75
VCC − 0.75 > VCC − 1.1 V, which satisfies the requirement
The maximum voltage at the modulation output pins is equal to
VCC + (IMOD × 25)/2 = VCC + 0.75
VCC + 0.75 < VCC + 1.1 V, which satisfies the requirement
Headroom Calculations
To ensure proper device operation, the voltages on the IBIAS,
IMODP, and IMODN pins must meet the compliance voltage
specifications in Table 1.
Headroom calculations must be repeated for the minimum and
maximum values of the required IBIAS and IMOD ranges to
ensure proper device operation over all operating conditions.
Considering the typical application circuit shown in Figure 33,
the voltage at the IBIAS pin can be written as
BSET and MSET Pin Voltage Calculation
VIBIAS = VCC − VF − (IBIAS × RTOSA) − VLA
where:
VCC is the supply voltage.
VF is the forward voltage across the laser at low current.
RTOSA is the resistance of the TOSA.
To set the desired bias and modulation currents, the BSET and
MSET pins of the ADN2525 must be driven with the appropriate
dc voltage. The voltage range required at the BSET pin to generate
the required IBIAS range can be calculated using the BSET
voltage to IBIAS gain specified in Table 1. Assuming that
IBIAS = 40 mA and the typical IBIAS/VBSET ratio of 100 mA/V,
the BSET voltage is given by
VBSET =
VLA is the dc voltage drop across L5, L6, L7, and L8.
VLB is the dc voltage drop across L1, L2, L3, and L4.
For proper operation, the minimum voltage at the IBIAS pin
should be greater than 0.6 V, as specified by the minimum
IBIAS compliance specification in Table 1.
Assuming that the voltage drop across the 25 Ω transmission
lines is negligible and that VLA = 0 V, VF = 1 V, and IBIAS =
40 mA,
IBIAS (mA)
100 mA/V
=
40
= 0. 4 V
100
The BSET voltage range can be calculated using the required
IBIAS range and the minimum and maximum BSET voltage to
IBIAS gain values specified in Table 1.
The voltage required at the MSET pin to produce the desired
modulation current can be calculated using
VMSET =
VIBIAS = 3.3 − 1 − (0.04 × 25) = 1.3 V
IMOD
K
where K is the MSET voltage to IMOD ratio.
VIBIAS = 1.3 V > 0.6 V, which satisfies the requirement
The maximum voltage at the IBIAS pin must be less than the
maximum IBIAS compliance specification as described by
VCOMPLIANCE_MAX = VCC − 0.75 − 4.4 × IBIAS (A)
For this example:
VCOMPLIANCE_MAX = VCC – 0.75 − 4.4 × 0.04 = 2.53 V
The value of K depends on the actual resistance of the TOSA.
It can be read using the plot shown in Figure 29. For a TOSA
resistance of 25 Ω, the typical value of K = 120 mA/V. Assuming
that IMOD = 60 mA and using the preceding equation, the
MSET voltage is given by
VMSET =
VIBIAS = 1.3 V < 2.53 V, which satisfies the requirement
To calculate the headroom at the modulation current pins
(IMODP and IMODN), the voltage has a dc component equal
to VCC due to the ac-coupled configuration and a swing equal
to IMOD × 25 Ω. For proper operation of the ADN2525, the
IMOD (mA)
120 mA/V
=
60
= 0. 5 V
120
The MSET voltage range can be calculated using the required
IMOD range and the minimum and maximum K values. These
can be obtained from the minimum and maximum curves in
Figure 29.
Rev. B | Page 14 of 16
Data Sheet
ADN2525
OUTLINE DIMENSIONS
DETAIL A
(JEDEC 95)
0.30
0.23
0.18
0.50
BSC
13
PIN 1
INDICATOR AREA OPTIONS
16
12
1
1.75
1.60 SQ
1.45
EXPOSED
PAD
9
TOP VIEW
0.80
0.75
0.70
TOP VIEW
PKG-005138
SEATING
PLANE
0.50
0.40
0.30
(SEE DETAIL A)
4
8
5
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
0.20 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WEED-6.
02-23-2017-E
PIN 1
INDICATOR
3.10
3.00 SQ
2.90
Figure 34. 16-Lead Lead Frame Chip Scale Package [LFCSP]
3 mm × 3 mm Body and 0.75 mm Package Height
(CP-16-22)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
ADN2525ACPZ-R2
ADN2525ACPZ-500R7
ADN2525ACPZ-REEL7
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
16-Lead LFCSP, 250-Piece Reel
16-Lead LFCSP, 7” 1,500-Piece Reel
16-Lead LFCSP, 7” 500-Piece Reel
Z = RoHS Compliant part.
Rev. B | Page 15 of 16
Package Option
CP-16-22
CP-16-22
CP-16-22
Branding
F06
F06
F06
ADN2525
Data Sheet
NOTES
©2005–2017 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05077-0-4/17(B)
Rev. B | Page 16 of 16
工商网监
湘ICP备2023018690号
