Digital Input Stereo, 2 W, Class-D
Audio Power Amplifier
SSM2518
Datasheet
FEATURES
GENERAL DESCRIPTION
Filterless, digital input Class-D amplifier
Serial digital audio interface supports common formats
I2S, left justified, right justified, TDM1-16, and PCM
2 channels × 2 W into 4 Ω and 2 channels × 1.4 W into 8 Ω
with 1% THD+N, when using a 5 V supply
I2C control interface or standalone operation
91% efficiency at full scale into an 8 Ω load
97 dB signal-to-noise ratio (SNR), A-weighted
80 dB power supply rejection ratio (PSRR) at 217 Hz
Digital volume control: −71.25 dB to +24 dB in 0.375 dB steps
Supports a wide range of sample rates from 8 kHz to 96 kHz
Automatic sample rate detection
Can operate using 64 × fS BCLK as the MCLK source
2.5 V to 5.5 V speaker supply voltage (PVDD)
1.62 V to 3.6 V digital supply voltage (DVDD)
Pop-and-click suppression
Short-circuit and thermal protection with programmable
autorecovery
Smart power-down when no input signal is detected
Power-on reset
Low power modes for performance/power trade-offs
User selectable ultralow EMI emission mode
Programmable dynamic range compression (DRC) with
noise gate, expander, compressor, and limiter
Available in two packages
16-bump, 2.2 mm × 2.2 mm, 0.5 mm pitch WLCSP
20-lead, 4.0 mm × 4.0 mm LFCSP
The SSM2518 is a digital input, Class-D power amplifier that combines a digital-to-analog converter (DAC) and a sigma-delta
(Σ-Δ) Class-D modulator. This unique architecture enables
extremely low real-world power consumption from digital
audio sources with excellent audio performance. The SSM2518
is ideal for power sensitive applications, such as mobile phones
and portable media players, where system noise can corrupt
small analog signals such as those sent to an analog input audio
amplifier.
APPLICATIONS
Input is provided via a serial audio interface, programmable to
accept all common audio formats including I2S and TDM. Control
of the IC is provided via an I2C control interface. The SSM2518
can accept a variety of input MCLK frequencies and can use
BCLK as the clock source in some configurations.
Additional features include a soft digital volume control, deemphasis, and a programmable digital dynamic range
compressor.
The architecture of the SSM2518 provides a solution that offers
lower power and higher performance than existing DAC plus
Class-D solutions. Its digital interface also offers a better system
solution for other products whose sole audio source is digital,
such as wireless speakers, laptop PCs, portable digital televisions,
and navigation systems.
Mobile phones
Portable media players
Laptop PCs
Wireless speakers
Portable gaming
Small LCD televisions
Navigation systems
Rev. B
Using the SSM2518, audio data can be transmitted to the amplifier
over a standard digital audio serial interface, thereby significantly
reducing the effect of noise sources such as GSM interference or
other digital signals on the transmitted audio. The closed-loop
digital input design retains the benefits of an all digital amplifier,
yet enables very good PSRR and audio performance. The three
level, Σ-Δ Class-D modulator is designed to provide the least
amount of EMI interference, the lowest quiescent power dissipation, and the highest audio efficiency without sacrificing
audio quality.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2011–2018 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
SSM2518
Datasheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Digital Audio Formats ................................................................... 20
Applications ....................................................................................... 1
Stereo Mode ................................................................................ 20
General Description ......................................................................... 1
TDM, 50% Duty Cycle Mode ................................................... 20
Revision History ............................................................................... 3
TDM, Pulse Mode ...................................................................... 20
Functional Block Diagram .............................................................. 4
PCM, Multichannel Mode ........................................................ 21
Specifications..................................................................................... 5
PCM Mono Mode ...................................................................... 21
Performance Specifications ......................................................... 5
I C Configuration Interface .......................................................... 22
Power Supply Requirements ....................................................... 6
Overview ..................................................................................... 22
Digital Input/Output .................................................................... 6
Register Summary (REG_MAP) .................................................. 25
Digital Interpolation Filter .......................................................... 6
Register (REG_MAP) Details ....................................................... 26
Digital Timing ............................................................................... 7
Absolute Maximum Ratings ....................................................... 8
Software Reset and Master Software Power-down Control
Register ........................................................................................ 26
Thermal Resistance ...................................................................... 8
Edge Speed and Clocking Control Register ............................ 27
ESD Caution .................................................................................. 8
Serial Audio Interface and Sample Rate Control Register .... 28
Pin Configuration and Function Descriptions ............................. 9
Serial Audio Interface Control Register .................................. 29
Typical Performance Characteristics ........................................... 11
Channel Mapping Control Register ......................................... 30
Theory of Operation ...................................................................... 14
Left Channel Volume Control Register ................................... 31
Power Supplies ............................................................................ 14
Right Channel Volume Control Register ................................ 32
Power-Down Modes................................................................... 14
Volume and Mute Control Register ......................................... 33
Power-On Reset/Voltage Supervisor........................................ 14
Fault Control 1 Register............................................................. 34
Master and Bit Clock.................................................................. 14
Power and Fault Control Register ............................................ 35
Typical Application Circuit ........................................................... 16
DRC Control 1 Register............................................................. 36
Digital Audio Interface .................................................................. 17
DRC Control 2 Register............................................................. 37
Channel Mapping ....................................................................... 17
DRC Control 3 Register............................................................. 38
Sample Rate Detection ............................................................... 17
DRC Control 4 Register............................................................. 40
Standalone Mode ........................................................................ 17
DRC Control 5 Register............................................................. 41
Low Power Modes ...................................................................... 17
DRC Control 6 Register............................................................. 42
Dynamic Range Control ............................................................ 17
DRC Control 7 Register............................................................. 44
Mute Options .............................................................................. 18
DRC Control 8 Register............................................................. 45
Volume Control .......................................................................... 18
DRC Control 9 Register............................................................. 46
De-emphasis Filter ..................................................................... 18
Packaging and Ordering Information ......................................... 47
Analog Gain ................................................................................ 18
Outline Dimensions ................................................................... 47
Fault Detection and Recovery................................................... 19
Ordering Guide .......................................................................... 48
2
Rev. B | Page 2 of 48
Datasheet
SSM2518
REVISION HISTORY
1/2018—Rev. A to Rev. B
Changed CP-20-10 to CP-20-8 .................................... Throughout
Changes to Figure 35 ......................................................................23
Updated Outline Dimensions ........................................................47
Changes to Ordering Guide ...........................................................48
11/2011—Rev. 0 to Rev. A
Added LFCSP...................................................................... Universal
Changes to Features Section ............................................................ 1
Changes to Table 1, Supply Current Parameter ............................ 5
Changes to Table 3, Input Voltage Parameter................................ 6
Changes to Table 7 ............................................................................ 8
Added Figure 5 and Table 9, Renumbered Sequentially ............10
Changes to Power-Down Modes Section .....................................14
Changes to Master and Bit Clock Section ....................................14
Changes to Sample Rate Detection Section .................................17
10/2011—Revision 0: Initial Version
Rev. B | Page 3 of 48
SSM2518
Datasheet
FUNCTIONAL BLOCK DIAGRAM
DVDD
SA_MOD
PVDD
GND
POWER-ON
RESET
BCLK
I2S
VOLUME
CONTROL
DRC
DAC
Σ-Δ
CLASS-D
MODULATOR
SDATA
SD
CLOCKING
POWER
CONTROL
I2C
MCLK
SDA SCL
ADDR
Figure 1.
Rev. B | Page 4 of 48
FULL BRIDGE
POWER
STAGE
FULL BRIDGE
POWER
STAGE
OUTL+
OUTL–
OUTR+
OUTR–
10242-001
LRCLK
Datasheet
SSM2518
SPECIFICATIONS
All specifications at PVDD = 5.0 V, DVDD = 1.8 V, fS = 48 kHz, MCLK = 128 × fS, TA = 25°C, RL = 8 Ω + 15 µH, LP_MODE = 0, volume
control = 0 dB, unless otherwise noted.
PERFORMANCE SPECIFICATIONS
Table 1.
Parameter
DEVICE CHARACTERISTICS
Symbol
Test Conditions/Comments
PO
f = 1 kHz, BW = 20 kHz
RL = 4 Ω, THD = 1%, PVDD = 5.0 V
RL = 4 Ω, THD = 10%, PVDD = 5.0 V
RL = 8 Ω, THD = 1%, PVDD = 5.0 V
RL = 8 Ω, THD = 10%, PVDD = 5.0 V
RL = 4 Ω, THD = 1%, PVDD = 3.6 V
RL = 4 Ω, THD = 10%, PVDD = 3.6 V
RL = 8 Ω, THD = 1%, PVDD = 3.6 V
RL = 8 Ω, THD = 10%, PVDD = 3.6 V
RL = 4 Ω, THD = 1%, PVDD = 2.5 V
RL = 4 Ω, THD = 10%, PVDD = 2.5 V
RL = 8 Ω, THD = 1%, PVDD = 2.5 V
RL = 8 Ω, THD = 10%, PVDD = 2.5 V
PO = 1.4 W, 8 Ω, PVDD = 5.0 V, normal operation
PO = 1.4 W, 8 Ω, PVDD = 5.0 V, ultralow EMI operation
PO = 0.5 W into 8 Ω each channel, f = 1 kHz, PVDD = 5 V
PO = 0.25 W into 8 Ω each channel, f = 1 kHz, PVDD = 3.6 V
PO = 1 W, f = 1 kHz, PVDD = 5 V
Output Power
Efficiency
η
Total Harmonic Distortion
Plus Noise
THD + N
Channel Separation
Average Switching Frequency
Differential Output Offset
Power Supply Rejection Ratio
XTALK
fSW
VOOS
PSRRDC
PSRRGSM
PSRRGSM
IPVDD
Supply Current
PVDD
DVDD
Output Noise Voltage
Signal-to-Noise Ratio
Mute Attenuation
IDVDD
en
SNR
PVDD = 2.5 V to 5.0 V
VRIPPLE = 100 mV rms at 217 Hz, dither input
VRIPPLE = 100 mV rms at 217 Hz, no input
Dither input, no load, PVDD = 5.0 V
Dither input, no load, PVDD = 3.6 V
Dither input, no load, PVDD = 2.5 V
Software power-down, SD = 1.8 V, SPWDN = 1, PVDD = 3.6 V
Hardware power-down, SD = 0 V, PVDD = 3.6 V
Dither input, no load, DVDD = 3.3 V
Dither input, no load, DVDD = 1.8 V
Dither input, no load, DVDD = 1.8 V, fS = 8 kHz
Software power-down, SD = 1.8 V, SPWDN = 1, DVDD = 1.8 V
Hardware power-down, SD = 0 V, DVDD = 1.8 V
PVDD = 5 V, f = 20 Hz to 20 kHz, dither input, A-weighted
PVDD = 3.6 V, f = 20 Hz to 20 kHz, dither input, A-weighted
A-weighted, referred to 0 dBFS, PVDD = 3.6 V
Soft mute on
Rev. B | Page 5 of 48
Min
70
100
Typ
Max
Unit
2
2.5
1.42
1.8
1.3
1.7
0.75
0.94
0.4
0.45
0.275
0.35
91
86
0.04
0.03
108
280
2.0
80
80
100
4.7
W
W
W
W
W
W
W
W
W
W
W
W
%
%
%
%
dB
kHz
mV
dB
dB
dB
mA
4.4
3.8
4
100
3.0
1.5
0.25
2.5
100
50
40
97
mA
mA
µA
nA
mA
mA
mA
µA
nA
µV
µV
dB
dB
SSM2518
Datasheet
POWER SUPPLY REQUIREMENTS
Table 2.
Parameter
PVDD
DVDD
Min
2.5
1.62
Typ
3.6
1.8
Max
5.5
3.6
Unit
V
V
DIGITAL INPUT/OUTPUT
Table 3.
Parameter
INPUT VOLTAGE
High (VIH)
Low (VIL)
Min
Typ
0.7 × DVDD
1.35
−0.3
−0.3
INPUT LEAKAGE CURRENT
High (IIH)
Low (IIL)
MCLK INPUT LEAKAGE CURRENT
High (IIH)
Low (IIL)
INPUT CAPACITANCE
Max
Unit
Test Conditions/Comments
3.6
5.5
+0.3 × DVDD
+0.35
V
V
V
V
ADDR, MCLK, BCLK, LRCLK, SDATA, SAMOD
SD, SDA, SCL
ADDR, MCLK, BCLK, LRCLK, SDATA, SAMOD
SD, SDA, SCL
1
1
µA
µA
Excluding MCLK
Excluding MCLK and bidirectional pin
3
3
5
µA
µA
pF
DIGITAL INTERPOLATION FILTER
Table 4.
Parameter
PASS BAND
−3 dB
Ripple
TRANSITION BAND
STOP BAND
Attenuation
GROUP DELAY
1
Factor
Min
0.4535 × fS
Typ 1
Max
22
±0.01
0.5 × fS
0.5465 × fS
24
26
70
25/fS
Typical value given for 48 kHz sample rate.
Rev. B | Page 6 of 48
521
Unit
kHz
dB
kHz
kHz
dB
µs
Datasheet
SSM2518
DIGITAL TIMING
All timing specifications are given for the default setting (I2S mode) of the serial input port.
Table 5.
Parameter
MASTER CLOCK
tMP
tMP
SERIAL PORT
tBIL
tBIH
tLIS
tLIH
tSIS
tSIH
I2C PORT
fSCL
tSCLH
tSCLL
tSCS
tSCH
tDS
tSCR
tSCF
tSDR
tSDF
tBFT
Min
Limit
Max
74
148
136
271
40
40
10
10
10
10
400
0.6
1.3
0.6
0.6
100
300
300
300
300
0.6
Unit
Description
ns
ns
MCLK period, 256 × fS mode (MCS = b0010)
MCLK period, 128 × fS mode (MCS = b0001)
ns
ns
ns
ns
ns
ns
BCLK low pulse width
BCLK high pulse width
Setup time from LRCLK or SDATA edge to BCLK rising edge
Hold time from BCLK rising edge to LRCLK or SDATA edge
SDATA setup time to BCLK rising
SDATA hold time from BCLK rising
kHz
μs
μs
μs
μs
ns
ns
ns
ns
ns
μs
SCL frequency
SCL high
SCL low
Setup time; relevant for repeated start condition
Hold time; after this period, the first clock is generated
Data setup time
SCL rise time
SCL fall time
SDA rise time
SDA fall time
Bus-free time (time between stop and start)
Digital Timing Diagrams
tBIH
tBP
BCLK
tBIL
tLIH
tLIS
LRCLK
SDATA
LEFT-JUSTIFIED
MODE
tSIS
MSB
MSB – 1
tSIH
tSIS
SDATA
I2C-JUSTIFIED
MODE
MSB
tSIH
tSIS
tSIS
MSB
LSB
tSIH
10242-002
SDATA
RIGHT-JUSTIFIED
MODE
tSIH
Figure 2. Serial Input Port Timing
tDS
tSCH
tSCH
SDA
tSCR
tSCLH
tSCS
START
CONDITION
tSCLL
tSCF
tBFT
STOP
CONDITION
Figure 3. I2C Port Timing
Rev. B | Page 7 of 48
10242-003
SCL
SSM2518
Datasheet
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Absolute maximum ratings apply at 25°C, unless otherwise noted.
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 6.
Parameter
PVDD Supply Voltage
DVDD Supply Voltage
Input Voltage (ADDR, MCLK, BCLK, LRCLK,
SDATA, SAMOD Pins)
Input Voltage (SD, SDA, and SCL Pins)
ESD Susceptibility
Storage Temperature Range
Operating Temperature Range
Junction Temperature Range
Lead Temperature (Soldering, 60 sec)
Table 7. Thermal Resistance
Rating
−0.3 V to +6 V
−0.3 V to +3.6 V
−0.3 V to +3.6 V
Package Type
16-ball, 2 mm × 2 mm WLCSP
20-lead, 4.0 mm × 4.0 mm LFCSP
−0.3 V to +6 V
4 kV
−65°C to +150°C
−40°C to +85°C
−65°C to +165°C
300°C
ESD CAUTION
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Rev. B | Page 8 of 48
θJA
56
54
Unit
°C/W
°C/W
Datasheet
SSM2518
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
BALL A1
INDICATOR
2
1
3
4
OUTR+
GND
PVDD OUTL+
OUTR–
SD
ADDR OUTL–
A
B
DVDD SAMOD
SCL
SDA
C
SDATA LRCLK BCLK
MCLK
TOP VIEW
(BALL SIDE DOWN)
Not to Scale
10242-009
D
Figure 4. WLCSP Pin Configuration
Table 8. Pin Function Descriptions, WLCSP
Pin No.
A1
B1
A4
B4
A3
A2
C1
B2
C3
C4
D4
D2
D3
D1
C2
B3
1
Mnemonic
OUTR+
OUTR−
OUTL+
OUTL−
PVDD
GND
DVDD
SD
SCL
SDA
MCLK
LRCLK
BCLK
SDATA
SAMOD
ADDR
Function1
O
O
O
O
P
P
P
I
I
I/O
I
I
I
I
I
I
Description
Right Channel Output Positive.
Right Channel Output Negative.
Left Channel Output Positive.
Left Channel Output Negative.
2.5 V to 5.5 V Amplifier Power.
Amplifier Ground.
1.62 V to 3.6 V Digital and Analog Power.
Power-Down Control, Active Low.
I2C Clock.
I2C Data.
Serial Audio Interface Master Clock.
I2S Word Clock.
I2S Bit Clock.
I2S Serial Data.
Standalone/I2C Mode Select. High = standalone mode, low = I2C mode.
I2C Address Select.
I is input, O is output, I/O is input/output, and P is power.
Rev. B | Page 9 of 48
Datasheet
SSM2518
TOP VIEW
(Not to Scale)
15
14
13
12
11
OUTR+
OUTR–
SD
DVDD
SAMOD
NOTES
1. CONNECT THE EXPOSED PAD TO GND.
10242-110
1
2
3
4
5
MCLK 6
BCLK 7
GND 8
LRCLK 9
SDATA 10
OUTL+
OUTL–
ADDR
SDA
SCL
20
19
18
17
16
PIN 1
INDICATOR
PVDD
GND
GND
GND
PVDD
SSM2518
Figure 5. LFCSP Pin Configuration
Table 9. Pin Function Descriptions, LFCSP
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
Mnemonic
OUTL+
OUTL−
ADDR
SDA
SCL
MCLK
BCLK
GND
LRCLK
SDATA
SAMOD
DVDD
SD
OUTR−
OUTR+
PVDD
GND
GND
GND
PVDD
Function1
O
O
I
I/O
I
I
I
P
I
I
I
P
I
O
O
P
P
P
P
P
Description
Left Channel Output Positive.
Left Channel Output Negative.
I2C Address Select.
I2C Data.
I2C Clock.
Serial Audio Interface Master Clock.
I2S Bit Clock.
Amplifier Ground.
I2S Word Clock.
I2S Serial Data.
Standalone/I2C Mode Select. High = standalone mode, low = I2C mode.
1.62 V to 3.6 V Digital and Analog Power.
Power-Down Control, Active Low.
Right Channel Output Negative.
Right Channel Output Positive.
2.5 V to 5.5 V Amplifier Power.
Amplifier Ground.
Amplifier Ground.
Amplifier Ground.
2.5 V to 5.5 V Amplifier Power.
I is input, O is output, I/O is input/output, and P is power.
Rev. B | Page 10 of 48
Datasheet
SSM2518
TYPICAL PERFORMANCE CHARACTERISTICS
100
GAIN = 5V
MCLK = 256 × fS
RL = 8Ω, 33µH
100
2.5V
3.6V
5.0V
THD + N (%)
1
0.01
0.1
1
10
OUTPUT POWER (W)
0.01
0.001
10242-011
0.01
0.001
0.01
0.1
1
10
OUTPUT POWER (W)
Figure 6. THD + N vs. Output Power into 8 Ω, 5.0 V Gain Setting
Figure 9. THD + N vs. Output Power into 8 Ω, 3.6 V Gain Setting
100
100
GAIN = 5V
MCLK = 256 × fS
RL = 4Ω, 15µH
2.5V
3.6V
5.0V
10
GAIN = 3.6V
MCLK = 256 × fS
RL = 4Ω, 15µH
10242-014
0.1
2.5V
3.6V
5.0V
THD + N (%)
10
1
0.1
1
0.01
0.1
10
1
OUTPUT POWER (W)
0.01
0.001
10242-012
0.01
0.001
0.01
0.1
10
1
OUTPUT POWER (W)
Figure 7. THD + N vs. Output Power into 4 Ω, 5.0 V Gain Setting
Figure 10. THD + N vs. Output Power into 4 Ω, 3.6 V Gain Setting
100
100
PVDD = 5V
GAIN = 5V
MCLK = 256 × fS
RL = 8Ω, 33µH
0.25W
0.5W
1.0W
10
PVDD = 5V
GAIN = 5V
MCLK = 256 × fS
RL = 4Ω, 15µH
10242-015
0.1
0.25W
0.5W
1.0W
THD + N (%)
10
1
0.1
1
0.01
10
100
1k
10k
FREQUENCY (Hz)
100k
10242-013
0.1
Figure 8. THD + N vs. Frequency, PVDD = 5 V, RL = 8 Ω
0.01
10
100
1k
10k
100k
FREQUENCY (Hz)
Figure 11. THD + N vs. Frequency, PVDD = 5 V, RL = 4 Ω
Rev. B | Page 11 of 48
10242-016
THD + N (%)
1
0.1
THD + N (%)
2.5V
3.6V
5.0V
10
10
THD + N (%)
GAIN = 3.6V
MCLK = 256 × fS
RL = 8Ω, 33µH
SSM2518
100
Datasheet
100
PVDD = 3.6V
GAIN = 3.6V
MCLK = 256 × fS
RL = 8Ω, 33µH
1
0.1
1
1k
10k
0.01
10
10242-017
100
100k
FREQUENCY (Hz)
PVDD = 2.5V
GAIN = 3.6V
MCLK = 256 × fS
RL = 8Ω, 33µH
1k
10k
100k
FREQUENCY (Hz)
Figure 12. THD + N vs. Frequency, PVDD = 3.6 V, RL = 8 Ω
100
100
10242-020
0.1
0.01
10
Figure 15. THD + N vs. Frequency, PVDD = 3.6 V, RL = 4 Ω
100
0.05W
0.10W
0.20W
PVDD = 2.5V
GAIN = 3.6V
MCLK = 256 × fS
RL = 4Ω, 15µH
0.05W
0.10W
0.20W
10
THD + N (%)
10
1
0.1
100
1k
10k
0.01
10
10242-018
0.01
10
100k
FREQUENCY (Hz)
4.0
DAC_LPM = 1
AMP_LPM = 1
DVDD = 1.8V
DITHER INPUT
QUIESCENT CURRENT (mA)
3.5
7
6
5
NO LOAD
8Ω + 33µH
4Ω + 33µH
3.5
4.0
4.5
5.0
5.5
6.0
SUPPLY VOLTAGE (V)
100k
MCLK = 256 × fS
DAC_LPM = 1, AMP_LPM = 1
3.0
2.5
2.0
1.5
1.0
8kHz 256 × fS
24kHz 256 × fS
48kHz 256 × fS
0.5
0
1.6
10242-019
3.0
10k
Figure 16. THD + N vs. Frequency, PVDD = 2.5 V, RL = 4 Ω
9
4
2.5
1k
FREQUENCY (Hz)
Figure 13. THD + N vs. Frequency, PVDD = 2.5 V, RL = 8 Ω
8
100
10242-021
0.1
1
2.0
2.4
2.8
3.2
3.6
SUPPLY VOLTAGE (V)
Figure 17. Quiescent Current (Digital Core) vs. Supply Voltage
Figure 14. Quiescent Current (Power Stage) vs. Supply Voltage
Rev. B | Page 12 of 48
10242-022
THD + N (%)
0.125W
0.25W
0.5W
10
THD + N (%)
THD + N (%)
10
QUIESCENT CURRENT (mA)
PVDD = 3.6V
GAIN = 3.6V
MCLK = 256 × fS
RL = 4Ω, 15µH
0.125W
0.25W
0.5W
Datasheet
2.5
SSM2518
1.4
GAIN = 5V
RL = 4Ω, 15µH
1kHz
GAIN = 5V
RL = 8Ω, 33µH
1.2 1kHz
1.0
OUTPUT POWER ( W)
OUTPUT POWER (W)
2.0
1.5
1.0
0.8
0.6
0.4
0.5
0.2
3.0
3.5
4.0
4.5
5.0
SUPPLY VOLTAGE (V)
0
2.5
10242-024
0
2.5
4.0
4.5
5.0
5V
3.6V
2.5V
90
80
70
70
EFFICIENCY (%)
60
50
40
60
50
40
30
30
20
20
10
10
RL = 4Ω, 15µΗ
0.4
0.8
1.2
1.6
2.0
2.4
2.8
3.2
3.6
4.0
4.4
4.8
COMBINED OUTPUT POWER, BOTH CHANNELS (W)
0
10242-028
0
RL = 8Ω + 33µΗ
0
0.4
0.8
1.2
1.6
2.0
2.4
2.8
3.2
COMBINED OUTPUT POWER, BOTH CHANNELS (W)
10175-029
EFFICIENCY (%)
100
80
0
3.5
Figure 21. Maximum Output Power vs. Supply Voltage, RL = 8 Ω
5V
3.6V
2.5V
90
3.0
SUPPLY VOLTAGE (V)
Figure 18. Maximum Output Power vs. Supply Voltage, RL = 4 Ω
100
1%
5%
10%
10175-026
1%
5%
10%
Figure 22. Efficiency vs. Output Power into 8 Ω
Figure 19. Efficiency vs. Output Power into 4 Ω
0
0
PVDD = 5V
RL = 8Ω, 33μH
P
O = 100mW
–20
–10
–20
PSRR (dB)
–30
–60
–80
LEFT TO RIGHT
–40
–50
–60
PVDD = 2.5V
PVDD = 5V
–70
–100
–80
–140
20
PVDD = 3.6V
–90
RIGHT TO LEFT
200
2k
FREQUENCY (Hz)
20k
–100
10
100
1k
10k
FREQUENCY (Hz)
Figure 23. PSRR vs. Frequency
Figure 20. Crosstalk vs. Frequency
Rev. B | Page 13 of 48
100k
10242-030
–120
10242-027
CROSSTALK (dB)
–40
SSM2518
Datasheet
THEORY OF OPERATION
The SSM2518 is fully integrated 2-channel digital input, Class-D
output audio amplifier. The SSM2518 receives digital audio input
and produces the PDM differential switching outputs using the
internal power stage. The part has built in protection for overtemperature as well as overcurrent conditions. The SSM2518
also has built in soft turn on and soft turn off for pop-and-click
suppression. The part has programmable register control via the
I2C port.
POWER SUPPLIES
The SSM2518 requires two power supplies: PVDD and DVDD.
Descriptions of each of these supplies follow.
PVDD
monitors the incoming digital audio signal. If this is zero for
1024 consecutive samples, regardless of sample rate, it puts the
IC in the smart power-down state wherein all blocks, except the
I2S and I2C ports, are placed in a low power state. Once a single
nonzero input is received on the I2S interface, the SSM2518 leaves
this state and resumes normal operation.
POWER-ON RESET/VOLTAGE SUPERVISOR
The SSM2518 includes an internal power-on reset and voltage
supervisor circuit. This circuit provides an internal reset to all
circuitry whenever PVDD or DVDD is substantially below the
nominal operating threshold. This circuit simplifies supply
sequencing during initial power-on.
The PVDD pin supplies power to the full bridge power stage
of a MOSFET and its associated drive, control, and protection
circuitry. PVDD can operate from 2.5 V to 5.5 V and must be
present to obtain audio output. Lowering the supply PVDD
results in lower output power and, correspondingly, lower
power consumption but does not degrade audio performance.
The circuit also monitors the power supplies to the SSM2518. If
the supply voltages fall below the nominal operating threshold,
this circuit stops the output and issues a reset. This ensures that
no damage occurs due to low voltage operation and that no pops
can occur under nearly any power removal condition.
DVDD
The SSM2518 requires an internal master clock to operate. This
clock must run at a frequency between 2.048 MHz and 6.144 MHz,
depending on the input sample rate, and it must be fully synchronous with the incoming audio data. This clock signal can be
derived from either the MCLK or BCLK pin, depending on the
configuration used.
The DVDD pin provides power to the digital logic circuitry and
determines the input trip points. DVDD can operate from 1.62 V
to 3.6 V and must be present to obtain audio output. Lowering
the supply voltage of DVDD results in lower power consumption but does not affect audio performance.
POWER-DOWN MODES
The SSM2518 offers a hardware shutdown pin, SD, which can
be used to set the IC to its lowest power state, with all blocks
disabled. This hardware shutdown mode is enabled when the
SD pin is pulled low.
When the hardware shutdown is removed, the IC begins in
software power-down mode, where all blocks except for the
I2C interface are disabled. To fully power up the amplifier, clear
S_RST (Bit 7 of Register 0x00). In addition to the software
power-down, the software master mute is enabled at the initial
state of the amplifier; therefore, no audio is output until Bit 0 of
Register 0x07 is cleared.
The left and right channels can be independently shut down
by setting setting L_PWDN and R_PWDN (Bit 1 and Bit 2,
respectively, in Register 0x09). Disabling a channel shuts down
the channel specific digital processing, DAC, Class-D modulator,
and power stage.
The SSM2518 also contains a smart power-down feature, which
is enabled by default. This feature can be disabled by clearing
APWDN_EN (Bit 0 in Register 0x09). When active, this feature
MASTER AND BIT CLOCK
If the MCLK pin is used, the internal clock is derived by either
dividing, passing through, or doubling the external clock signal
as required. The clock supplied to the MCLK pin can range from
2.048 MHz to 38.864 MHz. In this case, the external MCLK pin
signal can run at various multiples of the audio sample rate (fS).
The relationship between the MCLK rate and the audio sample
rate is determined by the master clock select (MCS) register setting,
Bits[4:1] in Register 0x00. Table 11 provides a summary of the
available options.
In addition, a bit clock must run at the same rate as the incoming
audio data on the SDATA pin. This clock can be supplied to the
BCLK pin, or it can be generated internally by dividing MCLK.
In this case, when BCLK_GEN (Bit 7 of Register 0x03) is set, the
logic level of the BCLK pin is used to select the audio interface
BCLK rate. Tie the BCLK pin to DVDD for 16 clock cycles per
channel; tie it to ground for 32 cycles per channel.
If the system bit clock is in the range of acceptable internal
master clock frequencies (between 2.048 MHz and 6.144 MHz),
then it can serve as both master clock and bit clock. Setting
NO_BCLK (Bit 5 of Register 0x00) routes the signal on the
Rev. B | Page 14 of 48
Datasheet
SSM2518
MCLK pin to serve as the internal bit clock as well. In this case,
tie the BCLK pin to ground.
Once the SSM2518 has entered its power-down state, it is
possible to gate the clocks to conserve system power. However, a
valid master clock must be present for the audio amplifier to
operate. It is best to use a low jitter clock (less than 1 ns peakto-peak) to ensure the specified audio performance.
Rev. B | Page 15 of 48
SSM2518
Datasheet
TYPICAL APPLICATION CIRCUIT
DVDD 1.62V TO 3.6V
AUDIO
PROCESSOR
DVDD
BCLK
4.7µF
PVDD
100nF
100nF
PVDD 2.5V TO 5.5V
*
FB2
MCLK
OUTL–
1.35V TO 5.5V
C2
470pF
FB3
SSM2518
OUTR+
C3
470pF
2.2kΩ
SCL
SYSTEM
MICROCONTROLLER
C1
470pF
LRCLK
SDATA
2.2kΩ
FB1
OUTL+
FB4
OUTR–
SDA
C4
470pF
SD
SAMOD
ADDR
*OPTIONAL FOR APPLICATIONS WITH >20cm SPEAKER CABLE.
Figure 24. Typical Application Circuit Using I2C Configuration
Rev. B | Page 16 of 48
10242-039
GND
Datasheet
SSM2518
DIGITAL AUDIO INTERFACE
The SSM2518 operates as a slave on the serial audio interface. It
is capable of receiving stereo I2S-style, left justified, or right
justified data. Mono, stereo, and multichannel PCM/TDM
interface formats are available. The data format and interface
style are selected by adjusting the SDATA_FMT and SAI fields
in Register 0x02. Note that, when operating in right justified
mode, the proper data width must be chosen. The function of the
LRCLK pin varies depending on the data format. See Figure 26
through Figure 30 for the expected audio formats for various
configurations.
CHANNEL MAPPING
Stereo audio formats and TDM formats with 2, 4, 8, or 16
channels are available. In these modes, the amplifier left and
right audio can be independently chosen from any of the
available channels using the two fields in Register 0x04. For
most digital interface formats, many of these options are not
present. For example, in stereo modes, only Channel 0 and
Channel 1 are valid, and in four-slot TDM mode, only
Channel 0, Channel 1, Channel 2, and Channel 3 are valid.
LOW POWER MODES
Two low power modes are available. If DAC_LPM (Bit 3 of
Register 0x09) is set, the digital-to-analog converter (DAC)
runs at half speed, reducing the quiescent current. This half
speed mode is also active when the MCS setting (Bits[4:1] of
Register 0x00) is set to its lowest value (MCS = 0000) because
the slowest acceptable MCLK rates can only support half speed
DAC operation.
If AMP_LPM (Bit 4 of Register 0x09) is set, the Σ-Δ modulator
runs in a special mode that offers lower quiescent current when
the output power is small, at the expense of slightly degraded
audio performance.
DYNAMIC RANGE CONTROL
SAMPLE RATE DETECTION
The dynamic range control, or DRC, can be used to reduce the
dynamic range of the audio signal. A common DRC scheme
involves applying a gain reduction to large output signals, along
with a net increase in gain for moderate to small signals. The
qualitative result is a louder speaker output for moderate output
levels without the undesired effects of amplifier clipping or
speaker overdrive at high levels.
The SSM2518 can be configured to automatically detect the
sample rate, or the sample rate can be entered manually into the
FS field (Bit 1 and Bit 0 of Register 0x02). The choice of
automatic or manual sample rate detection is made by setting
the ASR bit (Bit 0 of Register 0x01). Sample rate detection
functions properly only when MCS (Bits[4:1] of Register 0x00)
is set correctly.
To calculate the gain adjustment, an rms detector gives the
average level of the input signal, based on the averaging time set
by RMS_TAV (Bits[3:0] in Register 0x12). Based on this time
averaged level, the overall gain is adjusted so that the input/
output characteristic matches the specified compression curve.
This curve can be represented by a log-to-log graph with five
distinct regions, as shown in Figure 25.
NT
STANDALONE MODE
Pin
SCL
Standalone Function
FORMAT
SDA
MCLK_SEL
SD
SD
ADDR
GAIN
Pin Options
Low: I2S
High: left justified
Low: MCLK = 256 × fS
High: MCLK = 384 × fS
Low: shutdown/mute
High: normal operation
Low: +12 dB digital gain
High: 0 dB digital gain
In standalone mode, the volume control, dynamic range control,
and EMI control features are disabled. Automatic sample rate
detection and smart power-down are enabled. All other settings
are set to their default values.
LT
SMAX
CT
ET
WITHOUT DRC
WITH DRC
SMIN
WITHOUT DRC
WITH DRC
INPUT
10242-032
Table 10. Standalone Mode Pin Functions
CT
OUTPUT
When the SAMOD pin is pulled high, the SSM2518 can operate
in several common stereo formats without any I2C control. Some
details of the serial audio interface can be configured by tying
the unused I2C pins to ground or DVDD, as shown in Table 10.
In addition, the amplifier gain can be controlled via the ADDR pin.
ET
Figure 25. DRC Compression Curve: Log-to-Log Representation of the DRC
Output Level vs. Input Level
From bottom left to top right, these regions (shown in red) are
the noise gate, expander, linear region, compressor, and limiter.
The control points between these regions can be set using the
DRC control registers (Register 0x0A through Register 0x12)
using the variable names (CT, ET, and so forth) as shown on the
plot axes in Figure 25. Each element can be individually enabled
using the LIM_EN, COMP_EN, EXP_EN, and NG_EN bits in
Rev. B | Page 17 of 48
SSM2518
Datasheet
Register 0x0A. The entire DRC function can be enabled or
disabled using DRC_EN (Bits[1:0] of Register 0x0A).
Linear Region
For input amplitudes between the DRC_ET and DRC_CT
thresholds, the DRC attenuation is set to zero, that is, the input is
passed straight through to the output. This is the region in the
center of the compression curve (see Figure 25) with a 1:1 slope,
where the input and output amplitude are the same.
Compressor
Above the input level set by DRC_CT (Bits[3:0] of Register 0x0C), the output amplitude does not rise as quickly as
the input. This provides a smooth transition to the limiter
region, where the output stops increasing altogether at the input
level set by DRC_LT (Bits[7:4] of Register 0x0C). At this point,
the output level is DRC_SMAX (Bits[7:4] of Register 0x0E).
Limiter
When the input level is above the input level set by DRC_LT,
the output level does not exceed the level given by DRC_SMAX
(Bits[7:4] of Register 0x0E). Instead, the overall gain is reduced
to maintain that level without clipping.
Expander
When the expander is enabled and the input level falls below
the level set by DRC_ET (Bits[7:4] of Register 0x0D), the output
level begins to decrease more rapidly than the input. This
provides a smooth transition to the noise gate, where
sufficiently small signals are blocked completely.
When the input signal falls to the level set by DRC_NT
(Bits[3:0] of Register 0x0D), the output level is set by
DRC_SMIN (Bits[3:0] of Register 0x0E).
Noise Gate
When the noise gate is enabled and the input signal level falls
below the threshold set by DRC_NT for a period of time, the
output is set to zero. Set this at a level lower than all signals of
interest to block the output in periods of silence.
The period of time for which the input level must remain
below the noise gate threshold prior to the output setting to
zero is determined by HDT_NG, Bits[3:0] of Register 0x10.
Attack and Decay Rates
To prevent audible distortion effects as the gain changes, the
time constants for the attack (gain reduction) and decay (gain
increase) are adjustable. The attack time is set by DRC_ATT
(Bits[7:4] of Register 0x0F), and the decay time is set by
DRC_DEC (Bits[3:0] of Register 0x0F).
Between attack and decay, a hold time is used to prevent rapid
switching between increased gain and decreased gain. The hold
time is set by HDT_NOR (Bits[7:4] of Register 0x10).
Post-DRC Gain
Because the DRC feature may have an overall effect on the
system gain, a separate digital gain option is provided to allow
the user to compensate for this effect. This digital gain option is
independent of the volume control feature, allowing an overall
gain adjustment that remains separate from the volume settings.
This level is set by DRC_POST_G (Bits[5:2] of Register 0x11).
Depending on the application, the entire DRC block can be placed
before or after the volume controls (L_VOL and R_VOL). This
option is set by PRE_VOL (Bit 6 of Register 0x0A).
MUTE OPTIONS
Several mute options are available. Each channel can be muted
independently using the left channel mute (L_MUTE, Bit 1 of
Register 0x07) or the right channel mute (R_MUTE, Bit 2 of
Register 0x07). Alternatively, both channels can be muted
simultaneously using the master mute option (M_MUTE, Bit 0
of Register 0x07).
The master mute is enabled at system startup; therefore, it must
be disabled before any audio is produced.
The SSM2518 also contains an automatic mute feature. This
feature is enabled by setting AMUTE (Bit 7 of Register 0x07).
When active, this feature monitors the incoming digital audio
signal. When the data stream is zero for 2048 consecutive
frames (1024 stereo samples), the output is muted. When a
single nonzero input is received on the I2S interface, the
SSM2518 is unmuted and resumes normal operation.
VOLUME CONTROL
The SSM2518 has a digital volume control that allows independent control of the left and right channels via Registers 0x05
and 0x06, respectively. 255 levels are available, providing a
range from +24 dB to −71.25 dB in 0.375 dB increments. This is
a soft volume control, meaning that the gain is adjusted continuously from one value to another. This continuously adjusted
gain prevents the audible pop that occurs with an instantaneous
gain adjustment.
When VOL_LINK (Bit 3 in Register 0x07) is set, both channels
are linked to the left channel volume setting.
DE-EMPHASIS FILTER
A digital de-emphasis filter is provided to compensate for the
standard compact disc style preemphasis, which occurs in some
audio systems. This filter is designed for use with a 44.1 kHz
sample rate only. To enable the de-emphasis filter, set
DEEMP_EN (Bit 4 of Register 0x07).
ANALOG GAIN
The analog gain of the SSM2518 amplifier is set by ANA_GAIN
(Bit 5 of Register 0x07). Each gain setting is designed to match
the scaling needed for a specified PVDD voltage so that the
digital full-scale values correspond to the clipping points of the
amplifier at that voltage.
If PVDD is larger than the voltage specified in this register, the
digital scale does not fill the output voltage range and maximum
output power is reduced. Similarly, if PVDD is smaller than
Rev. B | Page 18 of 48
Datasheet
SSM2518
specified in this register, analog clipping may occur within the
range of possible digital codes.
FAULT DETECTION AND RECOVERY
Three fault conditions are detected by the SSM2518 fault
detection system: left channel overcurrent, right channel
overcurrent, and overtemperature. When any of these is
detected, the amplifier shuts down and a read-only I2C bit is set
to indicate the cause of the shutdown. The OC_L, OC_R, and
OT fault indicators are Bit 7, Bit 6, and Bit 5 (respectively) of
Register 0x08.
An autorecovery feature can be enabled for temperature faults,
current faults, or both, depending on the state of ARCV (Bit 1
and Bit 0 of Register 0x08).
If autorecovery is enabled, the amplifier waits a short time
(10 ms, 20 ms, 40 ms, or 80 ms) and attempts to recover. The
recovery delay is set by AR_TIME (Bit 7 and Bit 6 of Register 0x09).
The maximum number of consecutive recovery attempts can be
set to one, three, seven, or unlimited attempts; this number is
set by MAX_AR (Bit 3 and Bit 2 of Register 0x08).
If the autorecovery feature is disabled or the maximum number
of attempts has been reached, the amplifier remains shut down
until a software reset or manual fault recovery attempt occurs.
The manual fault recovery is triggered by setting the write-only
bit, MRCV (Bit 4 of Register 0x08).
Rev. B | Page 19 of 48
SSM2518
Datasheet
DIGITAL AUDIO FORMATS
STEREO MODE
SAI = 0
SDATA_FMT = 0 (I2S), 1 (LJ), 2 (RJ 24-bit), 3 (RJ 16-bit)
BCLK
ANY# BCLKs
LRCLK
LEFT CHANNEL
8 TO 32 BCLKs
SDATA LJ
RIGHT CHANNEL
8 TO 32 BCLKs
RIGHT CHANNEL
8 TO 32 BCLKs
LEFT CHANNEL
8 TO 32 BCLKs
SDATA RJ
LEFT CHANNEL
8 TO 32 BCLKs
RIGHT CHANNEL
8 TO 32 BCLKs
10242-004
SDATA I2S
Figure 26. Stereo Modes: I2S, Left Justified, and Right Justified
TDM, 50% DUTY CYCLE MODE
SAI = 1 (2 slots), 2 (4 slots), 3 (8 slots), 4 (16 slots)
SDATA_FMT = 0 (I2S), 1 (LJ), 2 (RJ 24-bit), 3 (RJ 16-bit)
BCLK_EDGE = 0
LRCLK_MODE = 0
SLOT_WIDTH = 0 (32 BCLKs), 1 (24 BCLKs), 2 (16 BCLKs)
BCLK
32/24/16 BCLKs
32/24/16 BCLKs
32/24/16 BCLKs
LRCLK
SDATA LJ
8 TO 32 BCLKs
8 TO 32 BCLKs
8 TO 32 BCLKs
CHANNEL 2
CHANNEL 1
SDATA RJ
8 TO 32 BCLKs
CHANNEL N
CHANNEL 2
CHANNEL 1
CHANNEL N
CHANNEL 2
8 TO 32 BCLKs
24 OR 16 BCLKs
CHANNEL N
24 OR 16 BCLKs
24 OR 16 BCLKs
10242-005
CHANNEL 1
8 TO 32 BCLKs
SDATA I2S
Figure 27. TDM Modes with 50% Duty Cycle LRCLK
TDM, PULSE MODE
SAI = 1 (2 slots), 2 (4 slots), 3 (8 slots), 4 (16 slots)
SDATA_FMT = 0 (I2S), 1 (LJ), 2 (RJ 24-bit), 3 (RJ 16-bit)
BCLK_EDGE = 0
LRCLK_MODE = 1
SLOT_WIDTH = 0 (32 BCLKs), 1 (24 BCLKs), 2 (16 BCLKs)
BCLK
32/24/16 BCLKs
32/24/16 BCLKs
32/24/16 BCLKs
LRCLK
CHANNEL 1
SDATA LJ
CHANNEL 1
SDATA RJ
8 TO 32 BCLKs
CHANNEL N
CHANNEL 2
8 TO 32 BCLKs
CHANNEL N
CHANNEL 2
8 TO 32 BCLKs
8 TO 32 BCLKs
8 TO 32 BCLKs
CHANNEL 1
24 OR 16 BCLKs
8 TO 32 BCLKs
CHANNEL 2
24 OR 16 BCLKs
Figure 28. TDM Modes with Pulse Mode LRCLK
Rev. B | Page 20 of 48
CHANNEL N
24 OR 16 BCLKs
10242-006
SDATA I2S
Datasheet
SSM2518
PCM, MULTICHANNEL MODE
SAI = 1 (2 channels), 2 (4 channels), 3 (8 channels), 4 (16 channels)
SDATA_FMT = 0 (I2S), 1 (LJ), 2 (RJ 24-bit), 3 (RJ 16-bit)
BCLK_EDGE = 1
LRCLK_MODE = 1
SLOT_WIDTH = 0 (32 BCLKs), 1 (24 BCLKs), 2 (16 BCLKs)
BCLK
32/24/16 BCLKs
32/24/16 BCLKs
32/24/16 BCLKs
LRCLK
SDATA LJ
CHANNEL 1
CHANNEL N
CHANNEL 2
CHANNEL 1
8 TO 32 BCLKs
8 TO 32 BCLKs
8 TO 32 BCLKs
CHANNEL 2
8 TO 32 BCLKs
SDATA RJ
CHANNEL N
8 TO 32 BCLKs
8 TO 32 BCLKs
CHANNEL 1
CHANNEL N
CHANNEL 2
24 OR 16 BCLKs
24 OR 16 BCLKs
24 OR 16 BCLKs
Figure 29. Multichannel PCM Modes
PCM MONO MODE
SAI = 5
SDATA_FMT = 0 (I2S), 1 (LJ), 2 (RJ 24-bit), 3 (RJ 16-bit)
BCLK_EDGE = 1
LRCLK_MODE = 1
BCLK
ANY # BCLKs
LRCLK
SDATA LJ
MONO CHANNEL
8 TO 32 BCLKs
MONO CHANNEL
8 TO 32 BCLKs
SDATA RJ
MONO CHANNEL
8 TO 32 BCLKs
Figure 30. Mono PCM Modes
Rev. B | Page 21 of 48
10242-008
SDATA I2S
10242-007
SDATA I2S
SSM2518
Datasheet
I2C CONFIGURATION INTERFACE
OVERVIEW
The SSM2518 supports a 2-wire serial (I2C-compatible) microprocessor bus driving multiple peripherals. Two pins, serial data
(SDA) and serial clock (SCL), carry information between the
SSM2518 and the system I2C master controller. The SSM2518
is always a slave on the bus, meaning it cannot initiate a data
transfer. Each slave device is recognized by a unique device
address. The device address byte format is shown in Figure 31.
The address resides in the first seven bits of the I2C write. The
LSB of this byte sets either a read or write operation.
Logic Level 1 corresponds to a read operation, and Logic Level 0
corresponds to a write operation. The full byte addresses are
shown in Figure 3, where the subaddresses are automatically
incremented at word boundaries and can be used for writing
large amounts of data to contiguous memory locations. This
increment happens automatically after a single word write
unless a stop condition is encountered. A data transfer is always
terminated by a stop condition.
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
0
1
1
0
1
ADDR
0
R/W
10242-033
Both SDA and SCL should have a 2.2 kΩ pull-up resistor on the
lines connected to them.
2
Figure 31. I C Device Address Byte Format
Addressing
Initially, each device on the I2C bus is in an idle state,
monitoring the SDA and SCL lines for a start condition and
the proper address. The I2C master initiates a data transfer by
establishing a start condition, defined by a high-to-low transition
on SDA while SCL remains high. This indicates that an
address/data stream follows. All devices on the bus respond to
the start condition and shift the next eight bits (the 7-bit
address plus the R/W bit) MSB first. The device that recognizes
the transmitted address responds by pulling the data line low
during the ninth clock pulse. The device address is determined
by the state of the ADDR pin. This ninth bit is known as an
acknowledge bit. All other devices withdraw from the bus at
this point and return to the idle condition. The R/W bit
determines the direction of the data. A Logic 0 on the LSB of
the first byte means that the master writes information to the
peripheral, whereas a Logic 1 means that the master reads
information from the peripheral after writing the subaddress
and repeating the start address. A data transfer takes place until
a stop condition is encountered. A stop condition occurs when
SDA transitions from low to high while SCL is held high. The
timing for the I2C port is shown in Figure 3.
Stop and start conditions can be detected at any stage during the
data transfer. If these conditions are asserted out of sequence with
normal read and write operations, the SSM2518 immediately
jumps to the idle condition. During a given SCL high period,
the user should issue only one start condition, one stop condition,
or a single stop condition followed by a single start condition. If
an invalid subaddress is issued by the user, the SSM2518 does
not issue an acknowledge and returns to the idle condition. If
the user exceeds the highest subaddress while in auto-increment
mode, one of two actions is taken. In read mode, the SSM2518
outputs the highest subaddress register contents until the master
device issues a no acknowledge, indicating the end of a read. A
no acknowledge condition is where the SDA line is not pulled
low on the ninth clock pulse of SCL. If the highest subaddress
location is reached while in write mode, the data for the invalid
byte is not loaded into any subaddress register, a no acknowledge
is issued by the SSM2518, and the part returns to the idle
condition.
I2C Read and Write Operations
Figure 33 shows the timing of a single word write operation.
Every ninth clock, the SSM2518 issues an acknowledge by
pulling SDA low.
Figure 34 shows the timing of a burst mode write sequence.
This figure shows an example where the target destination
registers are two bytes. The SSM2518 knows to increment its
subaddress register every byte because the requested subaddress
corresponds to a register or memory area with a byte word
length.
The timing of a single word read operation is shown in
Figure 35. Note that the first R/W bit is 0, indicating a write
operation. This is because the subaddress still needs to be
written to set up the internal address. After the SSM2518
acknowledges the receipt of the subaddress, the master must
issue a repeated start command followed by the chip address
byte with the R/W bit set to 1 (read). This causes the SSM2518
SDA to reverse and begin driving data back to the master. The
master then responds every ninth pulse with an acknowledge
pulse to the SSM2518.
Figure 36 shows the timing of a burst mode read sequence. This
figure shows an example where the target destination registers
are two bytes. The SSM2518 knows to increment its subaddress
register every byte because the requested subaddress corresponds
to a register or memory area with a byte word length.
Rev. B | Page 22 of 48
Datasheet
SSM2518
SCK
SDA
R/W
START BY
MASTER
ACK
ACK
FRAME 2
SUBADDRESS BYTE
FRAME 1
CHIP ADDRESS BYTE
SCK
(CONTINUED)
ACK
ACK
FRAME 3
DATA BYTE 1
STOP BY
MASTER
FRAME 4
DATA BYTE 2
START
BIT
CHIP ADDRESS
R/W = 0
(7 BITS)
ACK BY
SLAVE
SUBADDRESS
(8 BITS)
ACK BY
SLAVE
DATA BYTE 1
(8 BITS)
STOP
BIT
10242-035
Figure 32. I2C Read/Write Timing
START
BIT
CHIP ADDRESS ACK BY SUBADDRESS
SLAVE
R/W = 0
ACK BY
SLAVE
DATA- ACK BY
WORD 1 SLAVE
DATA- ACK BY
WORD 2 SLAVE
STOP
BIT
10242-036
Figure 33. Single-Word I2C Write Format
START
BIT
CHIP ADDRESS ACK BY SUBADDRESS
SLAVE
R/W = 0
ACK BY
SLAVE
START
BIT
CHIP ADDRESS
R/W = 1
ACK BY
SLAVE
DATA
BYTE 1
NO ACK
STOP
BIT
10242-037
Figure 34. Burst Mode I2C Write Format
START
BIT
CHIP ADDRESS ACK BY SUBADDRESS
SLAVE
R/W = 0
ACK BY
SLAVE
START
BIT
CHIP ADDRESS
R/W = 1
ACK BY
SLAVE
Figure 36. Burst Mode I2C Read Format
Rev. B | Page 23 of 48
DATAWORD 1
ACK BY
MASTER
STOP
BIT
10242-038
Figure 35. Single-Word I2C Read Format
10242-034
SDA
(CONTINUED)
SSM2518
Datasheet
MCLK Frequency Settings
Table 11. MCS Bit Field Setting: MCLK, Ratio, and Frequency
Input
Sample Rate
8 kHz
Ratio
MCLK
11.025
Ratio
kHz
MCLK
12 kHz
Ratio
MCLK
16 kHz
Ratio
MCLK
22.05
Ratio
kHz
MCLK
24 kHz
Ratio
MCLK
32 kHz
Ratio
MCLK
44.1 kHz
Ratio
MCLK
48 kHz
Ratio
MCLK
96 kHz
Ratio
MCLK
1
Setting 0
b0000 1
256 × fS
2.048 MHz
256 × fS
Setting 1
b0001
512 × fS
4.096 MHz
512 × fS
Setting 2
b0010
1024 × fS
8.192 MHz
1024 × fS
Setting 3
b0011
1536 × fS
12.288 MHz
1536 × fS
Setting 4
b0100
2048 × fS
16.384 MHz
2048 × fS
Setting 5
b0101
3072 × fS
24.576 MHz
3072 × fS
Setting 6
b0110
400 × fS
3.20 MHz
400 × fS
Setting 7
b0111
800 × fS
6.40 MHz
800 × fS
Setting 8
b1000
1600 × fS
12.80 MHz
1600 × fS
2.822 MHz
256 × fS
3.072 MHz
128 × fS
2.048 MHz
128 × fS
5.6448 MHz
512 × fS
6.144 MHz
256 × fS
4.096 MHz
256 × fS
11.2896 MHz
1024 × fS
12.288 MHz
384 × fS
8.192 MHz
512 × fS
16.9344 MHz
1536 × fS
18.432 MHz
768 × fS
12.288 MHz
768 × fS
22.5792 MHz
2048 × fS
24.576 MHz
1024 × fS
16.384 MHz
1024 × fS
33.8688 MHz
3072 × fS
38.864 MHz
1536 × fS
24.576 MHz
1536 × fS
4.41 MHz
400 × fS
4.80 MHz
200 × fS
3.20 MHz
200 × fS
8.82 MHz
800 × fS
9.60 MHz
400 × fS
6.40 MHz
400 × fS
17.64 MHz
1600 × fS
19.20 MHz
800 × fS
12.80 MHz
800 × fS
2.822 MHz
128 × fS
3.072 MHz
64 × fS
2.048 MHz
64 × fS
2.822 MHz
64 × fS
3.072 MHz
64 × fS
3.072 MHz
5.6448 MHz
256 × fS
6.144 MHz
128 × fS
4.096 MHz
128 × fS
5.6448 MHz
128 × fS
6.144 MHz
64 × fS
6.144 MHz
11.2896 MHz
512 × fS
12.288 MHz
256 × fS
8.192 MHz
256 × fS
11.2896 MHz
256 × fS
12.288 MHz
128 × fS
12.288 MHz
16.9344 MHz
768 × fS
18.432 MHz
384 × fS
12.288 MHz
384 × fS
16.9344 MHz
384 × fS
18.432 MHz
192 × fS
18.432 MHz
22.5792 MHz
1024 × fS
24.576 MHz
512 × fS
16.384 MHz
512 × fS
22.5792 MHz
512 × fS
24.576 MHz
256 × fS
24.576 MHz
33.8688 MHz
1536 × fS
38.864 MHz
768 × fS
24.576 MHz
768 × fS
33.8688 MHz
768 × fS
38.864 MHz
384 × fS
38.864 MHz
4.41 MHz
200 × fS
4.80 MHz
100 × fS
3.20 MHz
100 × fS
4.41 MHz
100 × fS
4.80 MHz
50 × fS
4.80 MHz
8.82 MHz
400 × fS
9.60 MHz
200 × fS
6.40 MHz
200 × fS
8.82 MHz
200 × fS
9.60 MHz
100 × fS
9.60 MHz
17.64 MHz
800 × fS
19.20 MHz
400 × fS
12.80 MHz
400 × fS
17.64 MHz
400 × fS
19.20 MHz
200 × fS
19.20 MHz
When using MCS = 0000, the chip automatically operates in low power mode.
Rev. B | Page 24 of 48
Datasheet
SSM2518
REGISTER SUMMARY (REG_MAP)
Table 12. REG_MAP Register Summary
Reg
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x11
0x12
Name
Reset_Power_Control
Edge_Clock_Control
Serial_Interface_Sample_Rate_Control
Serial_Interface_Control
Channel_Mapping_Control
Left_Volume_Control
Right_Volume_Control
Volume_Mute_Control
Fault_Control_1
Power_Fault_Control
DRC_Control_1
DRC_Control_2
DRC_Control_3
DRC_Control_4
DRC_Control_5
DRC_Control_6
DRC_Control_7
DRC_Control_8
DRC_Control_9
Bits
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
[7:0]
Bit 7
S_RST
RESERVED
RESERVED
BCLK_GEN
CH_SEL_R
L_VOL
R_VOL
AMUTE
OC_L
AR_TIME
RESERVED
PEAK_ATT
DRC_LT
DRC_ET
DRC_SMAX
DRC_ATT
HDT_NOR
RESERVED
RESERVED
Bit 6
RESERVED
Bit 5
NO_BCLK
Reset
0x05
EDGE
0x00
SDATA_FMT
SAI
FS
0x02
LRCLK_MODE LRCLK_POL SAI_MSB
SLOT_WIDTH
BCLK_EDGE RESERVED 0x00
CH_SEL_L
0x10
0x40
0x40
RESERVED
ANA_GAIN DEEMP_EN VOL_LINK R_MUTE L_MUTE
M_MUTE
0x81
OC_R
OT
MRCV
MAX_AR
ARCV
0x0C
RESERVED AMP_LPM DAC_LPM R_PWDN L_PWDN
APWDN_EN 0x99
PRE_VOL
LIM_EN
COMP_EN EXP_EN
NG_EN DRC_EN
0x7C
PEAK_REL
0x5B
DRC_CT
0x57
DRC_NT
0x89
DRC_SMIN
0x8C
DRC_DEC
0x77
HDT_NG
0x26
DRC_POST_G
RESERVED
0x1C
RMS_TAV
0x07
Rev. B | Page 25 of 48
Bit 4
MCS
Bit 3
Bit 2
Bit 1
Bit 0
SPWDN
ASR
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
SSM2518
Datasheet
REGISTER (REG_MAP) DETAILS
SOFTWARE RESET AND MASTER SOFTWARE POWER-DOWN CONTROL REGISTER
Address: 0x00, Reset: 0x05, Name: Reset_Power_Control
Table 13. Bit Descriptions for Reset_Power_Control
Bits
7
Bit Name
S_RST
Settings
0
1
6
5
RESERVED
NO_BCLK
0
1
[4:1]
MCS
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
0
SPWDN
0
1
Description
Software Reset. Write 1 to reset all internal blocks, including I2C registers,
to their initial state.
Normal operation
Software reset
Reserved.
Bit Clock Source Selection. Either the MCLK or BCLK pin can be routed
internally to the bit clock.
BCLK pin used as bit clock source. Typical configuration.
MCLK pin used as bit clock source. No BCLK pin connection is needed.
Master Clock Select. This must match the ratio between the input MCLK
frequency and the audio sample rate, as shown in Table 11.
64 × fS
128 × fS
256 × fS
384 × fS
512 × fS
768 × fS
100 × fS
200 × fS
400 × fS
Reserved
Software Master Power-Down. This places all blocks, except the I2C
interface, into a low power state.
Normal operation
Software master power-down
Rev. B | Page 26 of 48
Reset
0x0
Access
RW
0x0
0x0
RW
RW
0x2
RW
0x1
RW
Datasheet
SSM2518
EDGE SPEED AND CLOCKING CONTROL REGISTER
Address: 0x01, Reset: 0x00, Name: Edge_Clock_Control
Table 14. Bit Descriptions for Edge_Clock_Control
Bits
[7:3]
[2:1]
Bit Name
RESERVED
EDGE
Settings
00
01
10
11
0
ASR
0
1
Description
Reserved.
Edge Rate Control. This limits the edge rate of the switching output stage.
The low EMI operation modes reduce the edge speed, lowering EMI and
power efficiency.
No edge rate control
Low EMI
Lower EMI
Lowest EMI
Automatic Sample Rate Detection.
Automatic detection enabled
Manual sample rate selection given by FS field, Bits[1:0] of Register 0x02
Rev. B | Page 27 of 48
Reset
0x00
0x0
Access
RW
RW
0x0
RW
SSM2518
Datasheet
SERIAL AUDIO INTERFACE AND SAMPLE RATE CONTROL REGISTER
Address: 0x02, Reset: 0x02, Name: Serial_Interface_Sample_Rate_Control
Table 15. Bit Descriptions for Serial_Interface_Sample_Rate_Control
Bits
7
[6:5]
Bit Name
RESERVED
SDATA_FMT
Settings
00
01
10
11
[4:2]
SAI
000
001
010
011
100
101
110
111
[1:0]
FS
00
01
10
11
Description
Reserved.
Serial Data Format. Only required if SAI = 000.
I²S standard; data is delayed by one BCLK cycle
Left justified
Right justified, 24-bit data
Right justified, 16-bit data
Serial Audio Interface Format.
I2S, left justified, or right justified stereo (depending on SDATA_FMT)
2-slot TDM
4-slot TDM
8-slot TDM
16-slot TDM
Mono PCM
Reserved
Reserved
Manual Sample Rate Selection. Only required if ASR = 1 in Register 0x01.
8 kHz to 12 kHz
16 kHz to 24 kHz
32 kHz to 48 kHz
64 kHz to 96 kHz
Rev. B | Page 28 of 48
Reset
0x0
0x0
Access
RW
RW
0x0
RW
0x2
RW
Datasheet
SSM2518
SERIAL AUDIO INTERFACE CONTROL REGISTER
Address: 0x03, Reset: 0x00, Name: Serial_Interface_Control
Table 16. Bit Descriptions for Serial_Interface_Control
Bits
7
Bit Name
BCLK_GEN
Settings
0
1
6
LRCLK_MODE
0
1
5
LRCLK_POL
0
1
4
SAI_MSB
0
1
[3:2]
SLOT_WIDTH
00
01
10
11
1
BCLK_EDGE
0
1
0
RESERVED
Description
Internal BCLK Generator Enable.
Bit clock from BCLK pin is used
Internally generated bit clock is used
LRCLK Shape Selection. Required only for TDM modes.
50% duty cycle
1-bit pulse
LRCLK Polarity.
Rising edge (normal)
Falling edge (inverted)
Serial Data Bit Order.
MSB first
LSB first
TDM Slot Width. Required only for TDM modes.
32 BCLK cycles per slot
24 BCLK cycles per slot
16 BCLK cycles per slot
Reserved
BCLK Active Edge.
Rising BCLK edge used
Falling BCLK edge used
Reserved.
Rev. B | Page 29 of 48
Reset
0x0
Access
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
SSM2518
Datasheet
CHANNEL MAPPING CONTROL REGISTER
Address: 0x04, Reset: 0x10, Name: Channel_Mapping_Control
Table 17. Bit Descriptions for Channel_Mapping_Control
Bits
[7:4]
Bit Name
CH_SEL_R
Settings
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
[3:0]
CH_SEL_L
0000
0001
Description
Right Channel Select. Channel 0 valid when running in mono (PCM)
mode.
Channel 0 to Channel 1 valid when running in stereo and 2-slot TDM
modes.
Channel 0 to Channel 3 valid when running in 4-slot TDM mode.
Channel 0 to Channel 7 valid when running in 8-slot TDM mode.
Channel 0 to Channel 15 valid when running in 16-slot TDM mode.
Channel 0
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
Channel 9
Channel 10
Channel 11
Channel 12
Channel 13
Channel 14
Channel 15
Left Channel Select. Channel 0 valid when running in mono (PCM) mode.
Channel 0 to Channel 1 valid when running in stereo and 2-slot TDM
modes.
Channel 0 to Channel 3 valid when running in 4-slot TDM mode.
Channel 0 to Channel 7 valid when running in 8-slot TDM mode.
Channel 0 to Channel 15 valid when running in 16-slot TDM mode.
Channel 0
Channel 1
Rev. B | Page 30 of 48
Reset
0x1
Access
RW
0x0
RW
Datasheet
Bits
Bit Name
SSM2518
Settings
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
Description
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
Channel 9
Channel 10
Channel 11
Channel 12
Channel 13
Channel 14
Channel 15
Reset
Access
Reset
0x40
Access
RW
LEFT CHANNEL VOLUME CONTROL REGISTER
Address: 0x05, Reset: 0x40, Name: Left_Volume_Control
Table 18. Bit Descriptions for Left_Volume_Control
Bits
[7:0]
Bit Name
L_VOL
Settings
00000000
00000001
00000010
00000011
00000100
00000101
…
00111111
01000000
01000001
01000010
…
11111101
11111110
11111111
Description
Left Channel Volume Control. Adjusts the digital gain in 0.375 dB
increments.
+24 dB
+23.625 dB
+23.35 dB
+22.875 dB
+22.5 dB
+22.125 dB
…
+0.375 dB
0 dB
−0.375 dB
−0.750 dB
…
−70.875 dB
−71.25 dB
Mute
Rev. B | Page 31 of 48
SSM2518
Datasheet
RIGHT CHANNEL VOLUME CONTROL REGISTER
Address: 0x06, Reset: 0x40, Name: Right_Volume_Control
Table 19. Bit Descriptions for Right_Volume_Control
Bits
[7:0]
Bit Name
R_VOL
Settings
00000000
00000001
00000010
00000011
00000100
00000101
…
00111111
01000000
01000001
01000010
…
11111101
11111110
11111111
Description
Right Channel Volume Control. Adjusts the digital gain in 0.375 dB
increments.
+24 dB
+23.625 dB
+23.35 dB
+22.875 dB
+22.5 dB
+22.125 dB
…
+0.375 dB
0 dB
−0.375 dB
−0.750 dB
…
−70.875 dB
−71.25 dB
Mute
Rev. B | Page 32 of 48
Reset
0x40
Access
RW
Datasheet
SSM2518
VOLUME AND MUTE CONTROL REGISTER
Address: 0x07, Reset: 0x81, Name: Volume_Mute_Control
Table 20. Bit Descriptions for Volume_Mute_Control
Bits
7
Bit Name
AMUTE
Settings
0
1
6
5
RESERVED
ANA_GAIN
0
1
4
DEEMP_EN
0
1
3
VOL_LINK
0
1
2
R_MUTE
0
1
1
L_MUTE
0
1
0
M_MUTE
0
1
Description
Automatic Mute Enable. After 2048 slots (1024 stereo samples) have been
received with zero data, the outputs mute until nonzero data arrives.
Automute enabled
Automute disabled
Reserved.
Analog Gain. This sets the full-scale output level of the amplifier. The two
settings are scaled appropriately for 3.6 V and 5.0 V nominal supply
voltages.
Matched to 3.6 V supply
Matched to 5.0 V supply
Digital De-Emphasis Filter.
De-emphasis disabled (normal operation)
De-emphasis enabled
Volume Link. When this bit is enabled, both channels respond to the left
channel volume register.
Normal operation
Both channels linked to L_VOL (Register 0x05)
Right Channel Soft Mute.
Normal operation
Right channel muted
Left Channel Soft Mute.
Normal operation
Left channel muted
Master Mute Control. This bit soft mutes both channels.
Normal operation
Master mute
Rev. B | Page 33 of 48
Reset
0x1
Access
RW
0x0
0x0
RW
RW
0x0
RW
0x0
RW
0x0
RW
0x0
RW
0x1
RW
SSM2518
Datasheet
FAULT CONTROL 1 REGISTER
Address: 0x08, Reset: 0x0C, Name: Fault_Control_1
Table 21. Bit Descriptions for Fault_Control_1
Bits
7
Bit Name
OC_L
Settings
0
1
6
OC_R
0
1
5
OT
0
1
4
MRCV
0
1
[3:2]
MAX_AR
00
01
10
11
[1:0]
ARCV
00
01
10
11
Description
Left Channel Overcurrent Fault. Read only.
Normal operation
Left channel overcurrent fault
Right Channel Overcurrent Fault. Read only.
Normal operation
Right channel overcurrent fault
Overtemperature Fault Status. Read only.
Normal operation
Overtemperature fault
Manual Fault Recovery. Available only when ARCV = 11. Write only.
Normal operation
When written, attempt a manual fault recovery
Maximum Fault Recovery Attempts.
One attempt
Three attempts
Seven attempts
Unlimited attempts
Automatic Fault Recovery Selection.
Automatically recover from overtemperature and overcurrent faults
Automatically recover from overtemperature fault only
Automatically recover from overcurrent faults only
No automatic recovery
Rev. B | Page 34 of 48
Reset
0x0
Access
R
0x0
R
0x0
R
0x0
W
0x3
RW
0x0
RW
Datasheet
SSM2518
POWER AND FAULT CONTROL REGISTER
Address: 0x09, Reset: 0x99, Name: Power_Fault_Control
Table 22. Bit Descriptions for Power_Fault_Control
Bits
[7:6]
Bit Name
AR_TIME
Settings
00
01
10
11
5
4
RESERVED
AMP_LPM
0
1
3
DAC_LPM
0
1
2
R_PWDN
0
1
1
L_PWDN
0
1
0
APWDN_EN
0
1
Description
Automatic Recovery Delay Time. This determines the amount of time
delay between fault detection and an autorecovery attempt.
10 ms autorecovery delay
20 ms autorecovery delay
40 ms autorecovery delay
80 ms autorecovery delay
Reserved.
Class-D Amplifier Low Power Mode.
High performance operation
Low power operation
DAC Low Power Mode. In low power mode, the DAC runs at half speed.
Normal operation
Low power operation
Right Channel Power-Down.
Normal operation
Right channel powered down
Left Channel Power-Down.
Normal operation
Left channel powered down
Automatic Power-Down Enable. Automatic power-down automatically
puts the IC in a low power state when 2048 consecutive zero input
samples have been received.
Automatic power-down disabled
Automatic power-down enabled
Rev. B | Page 35 of 48
Reset
0x2
Access
RW
0x0
0x1
RW
RW
0x1
RW
0x0
RW
0x0
RW
0x1
RW
SSM2518
Datasheet
DRC CONTROL 1 REGISTER
Address: 0x0A, Reset: 0x7C, Name: DRC_Control_1
Table 23. Bit Descriptions for DRC_Control_1
Bits
7
6
Bit Name
RESERVED
PRE_VOL
Settings
0
1
5
LIM_EN
0
1
4
COMP_EN
0
1
3
EXP_EN
0
1
2
NG_EN
0
1
[1:0]
DRC_EN
00
01
10
11
Description
Reserved.
DRC Placement. This determines the placement of the DRC block in the
signal chain. When placed before the volume control, the thresholds are
relative to the input signal. When placed after the volume control, the
thresholds are relative to the output signal level. All thresholds are 6 dB
higher when placed after the volume control.
DRC operates after the volume control
DRC operates before the volume control
Limiter Enable. With the limiter enabled, the DRC_LT threshold (Bits[7:4] in
Register 0x0C) must be set.
Limiter disabled
Limiter enabled
Compressor Enable. With the compressor enabled, the DRC_CT and
DRC_SMAX thresholds (Bits[3:0] in Register 0x0C and Bits[7:4] in
Register 0x0E) must be set.
Compressor disabled
Compressor enabled
Expander Enable. With the expander enabled, the DRC_ET and DRC_SMIN
threshold values (Bits[7:4] in Register 0x0D and Bits[3:0] in Register 0x0E)
must be set.
Expander disabled
Expander enabled
Noise Gate Enable. With the noise gate enabled, the DRC_NT threshold
value (Bits[3:0] in Register 0x0D) must be set.
Noise gate disabled
Noise gate enabled
Master DRC Enable. This must be enabled for any of the DRC features to
function.
DRC disabled
Left channel DRC enabled
Right channel DRC enabled
Left and right channel DRC enabled
Rev. B | Page 36 of 48
Reset
0x0
0x1
Access
RW
RW
0x1
RW
0x1
RW
0x1
RW
0x1
RW
0x0
RW
Datasheet
SSM2518
DRC CONTROL 2 REGISTER
Address: 0x0B, Reset: 0x5B, Name: DRC_Control_2
Table 24. Bit Descriptions for DRC_Control_2
Bits
[7:4]
Bit Name
PEAK_ATT
Settings
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
[3:0]
PEAK_REL
0000
0001
0010
0011
0100
0101
0110
0111
Description
DRC Peak Detector Attack Time.
0 ms
0.09 ms
0.19 ms
0.37 ms
0.75 ms
1.5 ms
3 ms
6 ms
12 ms
24 ms
48 ms
96 ms
192 ms
384 ms
768 ms
1.536 sec
DRC Peak Detector Release Time.
0 ms
1.5 ms
3 ms
6 ms
12 ms
24 ms
48 ms
96 ms
Rev. B | Page 37 of 48
Reset
0x5
Access
RW
0xB
RW
SSM2518
Bits
Bit Name
Datasheet
Settings
1000
1001
1010
1011
1100
1101
1110
1111
Description
193 ms
384 ms
768 ms
1.536 sec
3.072 sec
6.144 sec
12.288 sec
24.576 sec
Reset
Access
Reset
0x5
Access
RW
DRC CONTROL 3 REGISTER
Address: 0x0C, Reset: 0x57, Name: DRC_Control_3
Table 25. Bit Descriptions for DRC_Control_3
Bits
[7:4]
Bit Name
DRC_LT
Settings
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
Description
DRC Limiter Threshold Setting. Relative to input.
0 dB
−1 dB
−2 dB
−3 dB
−4 dB
−5 dB
−6 dB
−7 dB
−8 dB
−10 dB
−12 dB
−14 dB
−16 dB
−18 dB
−20 dB
−22 dB
Rev. B | Page 38 of 48
Datasheet
Bits
[3:0]
Bit Name
DRC_CT
SSM2518
Settings
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
Description
DRC Compressor Lower Threshold Setting. Relative to input.
−4 dB
−6 dB
−8 dB
−10 dB
−12 dB
−14 dB
−16 dB
−18 dB
−20 dB
−22 dB
−24 dB
−26 dB
−28 dB
−30 dB
−32 dB
−34 dB
Rev. B | Page 39 of 48
Reset
0x7
Access
RW
SSM2518
Datasheet
DRC CONTROL 4 REGISTER
Address: 0x0D, Reset: 0x89, Name: DRC_Control_4
Table 26. Bit Descriptions for DRC_Control_4
Bits
[7:4]
Bit Name
DRC_ET
Settings
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
[3:0]
DRC_NT
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
Description
DRC Expander Upper Threshold Setting. Relative to input.
−36 dB
−39 dB
−42 dB
−45 dB
−48 dB
−51 dB
−54 dB
−57 dB
−60 dB
−63 dB
−66 dB
−69 dB
−72 dB
−75 dB
−78 dB
−81 dB
DRC Noise Gate Threshold Setting. Relative to input.
−51 dB
−54 dB
−57 dB
−60 dB
−63 dB
−66 dB
−69 dB
−72 dB
−75 dB
−78 dB
−81 dB
−84 dB
Rev. B | Page 40 of 48
Reset
0x8
Access
RW
0x9
RW
Datasheet
Bits
Bit Name
SSM2518
Settings
1100
1101
1110
1111
Description
−87 dB
−90 dB
−93 dB
−96 dB
Reset
Access
Reset
0x8
Access
RW
DRC CONTROL 5 REGISTER
Address: 0x0E, Reset: 0x8C, Name: DRC_Control_5
Table 27. Bit Descriptions for DRC_Control_5
Bits
[7:4]
Bit Name
DRC_SMAX
Settings
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
Description
DRC Limiter Threshold Setting. Relative to input.
0 dB
−1 dB
−2 dB
−3 dB
−4 dB
−5 dB
−6 dB
−7 dB
−8 dB
−10 dB
−12 dB
−14 dB
−16 dB
−18 dB
−20 dB
−22 dB
Rev. B | Page 41 of 48
SSM2518
Bits
[3:0]
Bit Name
DRC_SMIN
Datasheet
Settings
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
Description
DRC Minimum Output Signal Amplitude Setting. This is the minimum
output level produced by the DRC and is used to indicate the expander
lower threshold, or output signal level when the input rises beyond the
noise gate threshold.
−51 dB
−54 dB
−57 dB
−60 dB
−63 dB
−66 dB
−69 dB
−72 dB
−75 dB
−78 dB
−81 dB
−84 dB
−87 dB
−90 dB
−93 dB
−96 dB
Reset
0xC
Access
RW
Reset
0x7
Access
RW
DRC CONTROL 6 REGISTER
Address: 0x0F, Reset: 0x77, Name: DRC_Control_6
Table 28. Bit Descriptions for DRC_Control_6
Bits
[7:4]
Bit Name
DRC_ATT
Settings
0000
0001
0010
0011
0100
0101
Description
DRC Attack Time. Used to smooth the gain curve at the thresholds (knees)
of each DRC function.
0 ms
0.1 ms
0.19 ms
0.37 ms
0.75 ms
1.5 ms
Rev. B | Page 42 of 48
Datasheet
Bits
Bit Name
[3:0]
DRC_DEC
SSM2518
Settings
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
Description
3 ms
6 ms
12 ms
24 ms
48 ms
96 ms
192 ms
384 ms
768 ms
1.536 sec
DRC Decay Time. Used to smooth the gain curve at the thresholds (knees)
of each DRC function.
0 ms
1.5 ms
3 ms
6 ms
12 ms
24 ms
48 ms
96 ms
192 ms
384 ms
768 ms
1.536 sec
3.072 sec
6.144 sec
12.288 sec
24.576 sec
Rev. B | Page 43 of 48
Reset
Access
0x7
RW
SSM2518
Datasheet
DRC CONTROL 7 REGISTER
Address: 0x10, Reset: 0x26, Name: DRC_Control_7
Table 29. Bit Descriptions for DRC_Control_7
Bits
[7:4]
Bit Name
HDT_NOR
Settings
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
[3:0]
HDT_NG
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
Description
DRC Normal Operation Hold Time. Used to prevent the gain curve
calculation from increasing too quickly.
0 ms
0.67 ms
1.33 ms
2.67 ms
5.33 ms
10.66 ms
21.32 ms
42.64 ms
85.28 ms
170.56 ms
341.12 ms
682.24 ms
1.364 sec
Reserved
Reserved
Reserved
DRC Noise Gate Hold Time. Used to prevent the DRC from entering noise
gate too quickly.
0 ms
0.67 ms
1.33 ms
2.67 ms
5.33 ms
10.66 ms
21.32 ms
42.64 ms
85.28 ms
170.56 ms
Rev. B | Page 44 of 48
Reset
0x2
Access
RW
0x6
RW
Datasheet
Bits
Bit Name
SSM2518
Settings
1010
1011
1100
1101
1110
1111
Description
341.12 ms
682.24 ms
1.364 sec
Reserved
Reserved
Reserved
Reset
Access
Reset
0x0
0x7
Access
RW
RW
0x0
RW
DRC CONTROL 8 REGISTER
Address: 0x11, Reset: 0x1C, Name: DRC_Control_8
Table 30. Bit Descriptions for DRC_Control_8
Bits
[7:6]
[5:2]
Bit Name
RESERVED
DRC_POST_G
Settings
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
[1:0]
RESERVED
Description
Reserved.
Post-DRC Gain Adjust Setting. This can be used to add additional gain
after the DRC function to compensate for the overall reduction of system
gain due to the DRC.
+21 dB
+18 dB
+15 dB
+12 dB
+9 db
+6 dB
+3 dB
0 dB
−3 dB
−6 dB
−9 dB
−12 dB
−15 dB
−18 dB
−21 dB
−24 dB
Reserved.
Rev. B | Page 45 of 48
SSM2518
Datasheet
DRC CONTROL 9 REGISTER
Address: 0x12, Reset: 0x07, Name: DRC_Control_9
Table 31. Bit Descriptions for DRC_Control_9
Bits
[7:4]
[3:0]
Bit Name
RESERVED
RMS_TAV
Settings
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
Description
Reserved.
DRC RMS Detector Averaging Time. This is the averaging time for the rms
level that is compared to the DRC thresholds.
0 ms
1.5 ms
3 ms
6 ms
12 ms
24 ms
48 ms
96 ms
192 ms
384 ms
768 ms
1.536 sec
3.072 sec
6.144 sec
12.288 sec
24.576 sec
Rev. B | Page 46 of 48
Reset
0x0
0x7
Access
RW
RW
Datasheet
SSM2518
PACKAGING AND ORDERING INFORMATION
OUTLINE DIMENSIONS
2.250
2.210 SQ
2.170
3
4
2
1
A
BALL 1
IDENTIFIER
B
1.50
REF
C
D
0.50
REF
TOP VIEW
BOTTOM VIEW
(BALL SIDE DOWN)
0.660
0.600
0.540
(BALL SIDE UP)
SIDE VIEW
COPLANARITY
0.05
0.360
0.320
0.280
0.270
0.240
0.210
05-19-2011-A
SEATING
PLANE
Figure 37.16-Ball Wafer Level Chip Scale Package [WLCSP]
(CB-16-13)
Dimensions shown in millimeters
DETAIL A
(JEDEC 95)
0.30
0.25
0.18
0.50
BSC
16
PIN 1
INDIC ATOR AREA OPTIONS
(SEE DETAIL A)
20
1
15
2.75
2.60 SQ
2.35
EXPOSED
PAD
5
11
TOP VIEW
0.80
0.75
0.70
PKG-003502
SEATING
PLANE
SIDE VIEW
0.50
0.40
0.30
10
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
6
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WGGD-11.
Figure 38. 20-Lead Lead Frame Chip Scale Package [LFCSP]
4 mm × 4 mm Body and 0.75 mm Package Height
(CP-20-8)
Dimensions shown in millimeters
Rev. B | Page 47 of 48
0.20 MIN
10-12-2017-C
PIN 1
INDICATOR
4.10
4.00 SQ
3.90
SSM2518
Datasheet
ORDERING GUIDE
Model 1
SSM2518CBZ-RL
SSM2518CBZ-R7
SSM2518CPZ
SSM2518CPZ-R7
SSM2518CPZ-RL
EVAL-SSM2518Z
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
16-Ball WLCSP
16-Ball WLCSP
20-Lead LFCSP
20-Lead LFCSP
20-Lead LFCSP
Evaluation Board
Package Option
CB-16-13
CB-16-13
CP-20-8
CP-20-8
CP-20-8
Z = RoHS Compliant Part.
©2011–2018 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D10242-0-1/18(B)
www.analog.com/SSM2518
Rev. B | Page 48 of 48
工商网监
湘ICP备2023018690号
