LT3070-1
5A, Low Noise, Programmable Output,
85mV Dropout Linear Regulator
FEATURES
DESCRIPTION
Output Current: 5A
Dropout Voltage: 85mV Typical
nn Enable Function Soft-Starts the Reference
nn Digitally Programmable V
OUT : 0.8V to 1.8V
nn Digital Output Margining: ±1%, ±3% or ±5%
nn Low Output Noise: 25µV
RMS (10Hz to 100kHz)
nn Parallel Multiple Devices for 10A or More
nn Precision Current Limit: ±20%
nn ±1% Accuracy Over Line, Load and Temperature
nn Stable with Low ESR Ceramic Output Capacitors
(15µF Minimum)
nn High Frequency PSRR: 30dB at 1MHz
nn VIOC Pin Controls Buck Converter to Maintain Low
Power Dissipation and Optimize Efficiency
nn PWRGD/UVLO/Thermal Shutdown Flag
nn Current Limit with Foldback Protection
nn Thermal Shutdown
nn 28-Lead (4mm × 5mm × 0.75mm) QFN Package
The LT®3070-1 is a low voltage, UltraFast™ transient
response linear regulator. The device supplies up to 5A
of output current with a typical dropout voltage of 85mV.
A 0.01µF reference bypass capacitor decreases output
voltage noise to 25µVRMS. The LT3070-1 EN pin controls
the reference soft-start behavior in comparison to the
LT3070 which controls the reference soft-start via the
BIAS pin supply voltage. The LT3070-1’s high bandwidth
permits the use of low ESR ceramic capacitors, saving
bulk capacitance and cost. The LT3070-1’s features make
it ideal for high performance FPGAs, microprocessors or
sensitive communication supply applications.
nn
nn
APPLICATIONS
Output voltage is digitally selectable in 50mV increments
over a 0.8V to 1.8V range. A margining function allows
the user to adjust system output voltage in increments of
±1%, ±3% or ±5%. The IC incorporates a unique tracking
function to control a buck regulator powering the LT30701’s input. This tracking function drives the buck regulator
to maintain the LT3070-1’s input voltage to VOUT + 300mV,
minimizing power dissipation.
FPGA and DSP Supplies
ASIC and Microprocessor Supplies
nn Servers and Storage Devices
nn Post Buck Regulation and Supply Isolation
Internal protection includes UVLO, reverse-current protection, precision current limiting with power foldback and
thermal shutdown. The LT3070-1 regulator is available in
a thermally enhanced 28-lead, 4mm × 5mm QFN package.
nn
nn
All registered trademarks and trademarks are the property of their respective owners.
TYPICAL APPLICATION
Dropout Voltage
0.9V, 5A Regulator
50k
VIN
1.2V
PWRGD
2.2µF
IN
330µF
BIAS
EN
VO0
VO1
PWRGD
SENSE
LT3070-1
OUT
VO2
2.2µF*
4.7µF*
VOUT
0.9V
10µF* 5A
*X5R OR X7R CAPACITORS
MARGSEL
MARGTOL
VIOC
1nF
REF/BYP
GND
0.01µF
3070-1 TA01a
DROPOUT VOLTAGE (mV)
VBIAS
2.2V TO 3.6V
150
VIN = VOUT(NOMINAL)
120
90
VOUT = 1.8V
VBIAS = 3.3V
60
VOUT = 0.8V
VBIAS = 2.5V
30
0
0
1
3
4
5
2
OUTPUT CURRENT (A)
3070-1 TA01b
Rev 0
Document Feedback
For more information www.analog.com
1
LT3070-1
PIN CONFIGURATION
IN, OUT...................................................... –0.3V to 3.3V
BIAS.............................................................. –0.3V to 4V
VO2, VO1, VO0 Inputs..................................... –0.3V to 4V
MARGSEL, MARGTOL Input......................... –0.3V to 4V
EN Input........................................................ –0.3V to 4V
SENSE Input.................................................. –0.3V to 4V
VIOC, PWRGD Outputs................................. –0.3V to 4V
REF/BYP Output............................................ –0.3V to 4V
Output Short-Circuit Duration……...................Indefinite
Operating Junction Temperature (Note 2)
LT3070-1E/LT3070-1I......................... –40°C to 125°C
LT3070-1MP....................................... –55°C to 125°C
Storage Temperature Range................... –65°C to 150°C
VO0
VO1
VO2
GND
BIAS
EN
TOP VIEW
28 27 26 25 24 23
VIOC 1
22 MARGTOL
PWRGD 2
21 MARGSEL
REF/BYP 3
20 GND
GND 4
19 SENSE
29
GND
IN 5
18 OUT
IN 6
17 OUT
IN 7
16 OUT
IN 8
15 OUT
GND
GND
GND
GND
9 10 11 12 13 14
GND
(Note 1)
GND
ABSOLUTE MAXIMUM RATINGS
UFD PACKAGE
28-LEAD (4mm × 5mm) PLASTIC QFN
TJMAX = 125°C, θJA = 30°C/W TO 35°C/W
EXPOSED PAD (PIN 29) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT3070EUFD-1#PBF
LT3070EUFD-1#TRPBF
30701
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 125°C
LT3070IUFD-1#PBF
LT3070IUFD-1#TRPBF
30701
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 125°C
LT3070MPUFD-1#PBF
LT3070MPUFD-1#TRPBF 30701
28-Lead (4mm × 5mm) Plastic QFN
–55°C to 125°C
LEAD BASED FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT3070EUFD-1
LT3070EUFD-1#TR
30701
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 125°C
LT3070IUFD-1
LT3070IUFD-1#TR
30701
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 125°C
LT3070MPUFD-1
LT3070MPUFD-1#TR
30701
28-Lead (4mm × 5mm) Plastic QFN
–55°C to 125°C
Consult ADI Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Tape and reel specifications. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix.
Rev 0
2
For more information www.analog.com
LT3070-1
ELECTRICAL
CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. COUT = 15µF (Note 9), VIN = VOUT + 0.3V (Note 5), VBIAS = 2.5V unless
otherwise noted.
PARAMETER
CONDITIONS
MIN
IN Pin Voltage Range
VIN ≥ VOUT + 150mV, IOUT= 5A
l
TYP
0.95
2.2
UNITS
3.0
V
3.6
V
Regulated Output Voltage
VOUT = 0.8V, 10mA ≤ IOUT ≤ 5A, 1.05V ≤ VIN ≤ 1.25V
VOUT = 0.9V, 10mA ≤ IOUT ≤ 5A, 1.15V ≤ VIN ≤ 1.35V
VOUT = 1V, 10mA ≤ IOUT ≤ 5A, 1.25V ≤ VIN ≤ 1.45V
VOUT = 1.1V, 10mA ≤ IOUT ≤ 5A, 1.35V ≤ VIN ≤ 1.55V
VOUT = 1.2V, 10mA ≤ IOUT ≤ 5A, 1.45V ≤ VIN ≤ 1.65V, VBIAS = 3.3V
VOUT = 1.5V, 10mA ≤ IOUT ≤ 5A, 1.75V ≤ VIN ≤ 1.95V, VBIAS = 3.3V
VOUT = 1.8V, 10mA ≤ IOUT ≤ 5A, 2.05V ≤ VIN ≤ 2.25V, VBIAS = 3.3V
l
l
l
l
l
l
l
0.792
0.891
0.990
1.089
1.188
1.485
1.782
0.800
0.900
1.000
1.100
1.200
1.500
1.800
0.808
0.909
1.010
1.111
1.212
1.515
1.818
V
V
V
V
V
V
V
Regulated Output Voltage Margining
(Note 3)
MARGTOL = 0V, MARGSEL = VBIAS
MARGTOL = 0V, MARGSEL = 0V, IOUT = 10mA
l
l
0.8
–1.2
1
–1
1.2
–0.8
%
%
MARGTOL = FLOAT, MARGSEL = VBIAS
MARGTOL = FLOAT, MARGSEL = 0V, IOUT = 10mA
l
l
2.7
–3.3
3
–3
3.3
–2.7
%
%
MARGTOL = VBIAS, MARGSEL= VBIAS
MARGTOL = VBIAS, MARGSEL = 0V, IOUT = 10mA
l
l
4.6
–5.4
5
–5
5.4
–4.6
%
%
Line Regulation to VIN
VOUT = 0.8V, ∆VIN = 1.05V to 2.7V, VBIAS = 3.3V, IOUT = 10mA
VOUT = 1.8V, ∆VIN = 2.05V to 2.7V, VBIAS = 3.3V, IOUT = 10mA
l
l
1.0
1.0
mV
mV
Line Regulation to VBIAS
VOUT = 0.8V, ∆VBIAS = 2.2V to 3.6V, VIN = 1.1V, IOUT = 10mA
VOUT = 1.8V, ∆VBIAS = 3.25V to 3.6V, VIN = 2.1V, IOUT = 10mA
l
l
2.0
1.0
mV
mV
Load Regulation,
∆IOUT = 10mA to 5A
VBIAS = 2.5V, VIN = 1.05V, VOUT = 0.8V
–1.5
–3.0
–5.5
mV
mV
–2
–4.0
–7.5
mV
mV
–2
–4.0
–7.5
mV
mV
–2.5
–5.0
–9.0
mV
mV
–3
–7.0
–13
mV
mV
20
35
mV
50
65
85
mV
mV
85
120
150
mV
mV
50
300
65
400
µA
µA
BIAS Pin Voltage Range (Note 3)
l
MAX
l
VBIAS = 2.5V, VIN = 1.25V, VOUT = 1.0V
l
VBIAS = 3.3V, VIN = 1.45V, VOUT = 1.2V
l
VBIAS = 3.3V, VIN = 1.75V, VOUT = 1.5V
l
VBIAS = 3.3V, VIN = 2.05V, VOUT = 1.8V
l
Dropout Voltage,
VIN = VOUT(NOMINAL) (Note 6)
IOUT = 1A, VOUT = 1V
l
IOUT = 2.5A, VOUT = 1V
l
IOUT = 5A, VOUT = 1V
l
SENSE Pin Current
VIN = 1.1V, VSENSE = 0.8V
VBIAS = 3.3V, VIN = 2.1V, VSENSE = 1.8V
l
l
35
200
Rev 0
For more information www.analog.com
3
LT3070-1
ELECTRICAL
CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. COUT = 15µF (Note 9), VIN = VOUT + 0.3V (Note 5), VBIAS = 2.5V unless
otherwise noted.
PARAMETER
CONDITIONS
MIN
TYP
MAX
Ground Pin Current,
VIN = 1.3V, VOUT = 1V
IOUT = 10mA
IOUT = 5A
BIAS Pin Current in Nap Mode
l
l
0.65
0.9
1.1
1.35
1.8
2.3
mA
mA
EN = Low
l
120
200
320
µA
BIAS Pin Current,
VIN = 1.3V, VOUT = 1V
IOUT = 10mA
IOUT = 100mA
IOUT = 500mA
IOUT = 1A
IOUT = 2.5A
IOUT = 5A
l
l
l
l
l
l
0.75
1.25
2.0
2.6
3.5
4.5
1.08
1.8
3.0
3.8
5.2
6.9
1.5
2.4
4.0
5.0
7.0
10.0
mA
mA
mA
mA
mA
mA
Current Limit (Note 5)
VIN – VOUT < 0.3V, VBIAS = 3.3V
VIN – VOUT = 1.0V, VBIAS = 3.3V
VIN – VOUT = 1.7V, VBIAS = 3.3V
l
l
l
5.1
3.2
1.2
6.4
4.5
2.5
7.7
5.8
4.3
A
A
A
Reverse Output Current (Note 8)
VIN = 0V, VOUT = 1.8V
l
300
450
µA
PWRGD VOUT Threshold
Percentage of VOUT(NOMINAL), VOUT Rising
Percentage of VOUT(NOMINAL), VOUT Falling
l
l
90
85
93
88
%
%
PWRGD VOL
IPWRGD = 200µA (Fault Condition)
l
50
150
mV
VBIAS Undervoltage Lockout
VBIAS Rising
VBIAS Falling
l
l
1.1
0.9
1.55
1.4
2.1
1.7
V
V
l
250
300
350
mV
160
170
235
255
310
340
µA
µA
0.25
V
VBIAS – 0.9
V
VIN-VOUT Servo Voltage by VIOC
VIOC Output Current
VIN = VOUT(NOMINAL) + 150mV, Sourcing Out of the Pin
VIN = VOUT(NOMINAL) + 450mV, Sinking Into the Pin
l
l
VIL Input Threshold (Logic-0 State),
VO2, VO1, VO0, MARGSEL, MARGTOL
Input Falling
l
VIZ Input Range (Logic-Z State),
VO2, VO1, VO0, MARGSEL, MARGTOL
VIH Input Threshold (Logic-1 State),
VO2, VO1, VO0, MARGSEL, MARGTOL
Input Rising
87
82
l
0.75
l
VBIAS – 0.25
Input Hysteresis (Both Thresholds),
VO2, VO1, VO0, MARGSEL, MARGTOL
UNITS
V
60
mV
Input Current High,
VO2, VO1, VO0, MARGSEL, MARGTOL
VIH = VBIAS = 2.5V, Current Flows Into Pin
l
25
40
µA
Input Current Low,
VO2, VO1, VO0, MARGSEL, MARGTOL
VIL = 0V, VBIAS = 2.5V, Current Flows Out of Pin
l
25
40
µA
EN Pin Threshold
VOUT = Off to On, VBIAS = 2.5V
VOUT = On to Off, VBIAS = 2.5V
VOUT = Off to On, VBIAS =2.2V to 3.6V
VOUT = On to Off, VBIAS =2.2V to 3.6V
l
l
l
l
1.4
V
V
V
V
VEN = VBIAS = 2.5V
l
EN Pin Logic High Current
0.9
0.56 • VBIAS
0.36 • VBIAS
2.5
4.0
6.5
µA
Rev 0
4
For more information www.analog.com
LT3070-1
ELECTRICAL
CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. COUT = 15µF (Note 9), VIN = VOUT + 0.3V (Note 5), VBIAS = 2.5V unless
otherwise noted.
PARAMETER
CONDITIONS
MIN
TYP
EN Pin Logic Low Current
VEN = 0V
VBIAS Ripple Rejection
VBIAS = VOUT + 1.5VAVG, VRIPPLE =0.5VP-P , fRIPPLE = 120Hz,
VIN – VOUT = 300mV, IOUT = 2.5A
75
dB
VIN Ripple Rejection
(Notes 3, 4, 5)
VBIAS = 2.5V, VRIPPLE = 50mVP-P , fRIPPLE = 120Hz,
VIN – VOUT = 300mV, IOUT = 2.5A
66
dB
Reference Voltage Noise
(REF/BYP Pin)
CREF/BYP = 10nF, BW = 10Hz to 100kHz
10
µVRMS
Output Voltage Noise
VOUT = 1V, IOUT = 5A, CREF/BYP = 10nF, COUT = 15µF,
BW = 10Hz to 100kHz
25
µVRMS
0.1
l
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3070-1 regulators are tested and specified under pulse load
conditions such that TJ ≅ TA. The LT3070-1E is 100% tested at TA = 25°C.
Performance at –40°C and 125°C is assured by design, characterization
and correlation with statistical process controls. The LT3070-1I is
guaranteed over the –40°C to 125°C operating junction temperature range.
The LT3070-1MP is 100% tested and guaranteed over the –55°C to 125°C
operating junction temperature range.
Note 3: To maintain proper performance and regulation, the BIAS supply
voltage must be higher than the IN supply voltage. For a given VOUT , the
BIAS voltage must satisfy the following conditions: 2.2V ≤ VBIAS ≤ 3.6V
and VBIAS ≥ (1.25 • VOUT + 1V). For VOUT ≤ 0.95V, the minimum BIAS
voltage is limited to 2.2V.
Note 4: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specification does not apply
for all possible combinations of input voltage and output current. When
operating at maximum output current, limit the input voltage range to
VIN < VOUT + 500mV.
MAX
UNITS
µA
Note 5: The LT3070-1 incorporates safe operating area protection
circuitry. Current limit decreases as the VIN-VOUT voltage increases.
Current limit foldback starts at VIN – VOUT > 500mV. See the Typical
Performance Characteristics for a graph of Current Limit vs VIN – VOUT
voltage. The current limit foldback feature is independent of the thermal
shutdown circuity.
Note 6: Dropout voltage, VDO, is the minimum input to output voltage
differential at a specified output current. In dropout, the output voltage
equals VIN – VDO.
Note 7: GND pin current is tested with VIN = VOUT(NOMINAL) + 300mV and a
current source load. VIOC is a buffered output determined by the value of
VOUT as programmed by the VO2-VO0 pins. VIOC’s output is independent
of the margining function.
Note 8: Reverse output current is tested with the IN pins grounded and the
OUT + SENSE pins forced to the rated output voltage. This is measured as
current into the OUT + SENSE pins.
Note 9: Frequency Compensation: The LT3070-1 must be frequency
compensated at its OUT pins with a minimum COUT of 15µF configured
as a cluster of (15×) 1µF ceramic capacitors or as a graduated cluster
of 10µF/4.7µF/2.2µF ceramic capacitors of the same case size. Linear
Technology only recommends X5R or X7R dielectric capacitors.
Rev 0
For more information www.analog.com
5
LT3070-1
TYPICAL PERFORMANCE CHARACTERISTICS
Dropout Voltage vs Temperature
30
VIN = VOUT(NOMINAL)
TJ = 25°C
25
120
VOUT = 1.8V
VBIAS = 3.3V
60
VOUT = 0.8V
VBIAS = 2.5V
30
0
VIN = VOUT(NOMINAL)
IOUT = 1A
20
15
10
VOUT = 1.8V, VBIAS = 3.3V
VOUT = 0.8V, VBIAS = 2.5V
VOUT = 1.2V, VBIAS = 3.3V
5
0
1
3
4
2
OUTPUT CURRENT (A)
90
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
5
Dropout Voltage vs Temperature
60
30
VOUT = 1.8V, VBIAS = 3.3V
VOUT = 0.8V, VBIAS = 2.5V
VOUT = 1.2V, VBIAS = 3.3V
30
20
0.808
160
140
120
100
80
60
40
0
OUT = 1.8V
OUT = 1.5V
OUT = 0.8V
2.2
2.4
2.6 2.8 3.0
3.2
BIAS VOLTAGE (V)
3.4
1.212
ILOAD = 10mA
0.802
0.800
0.798
0.796
0.794
0.792
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3.6
30701 G06
Output Voltage (1.5V)
vs Temperature
1.515
ILOAD = 10mA
1.208
OUTPUT VOLTAGE (V)
1.006
1.002
1.000
0.998
0.996
0.994
ILOAD = 10mA
0.804
Output Voltage (1.2V)
vs Temperature
1.004
VOUT = 1.8V, VBIAS = 3.3V
VOUT = 0.8V, VBIAS = 2.5V
VOUT = 1.2V, VBIAS = 3.3V
30701 G05
Output Voltage (1V)
vs Temperature
OUTPUT VOLTAGE (V)
40
0.806
30701 G04
1.008
50
Output Voltage (0.8V)
vs Temperature
Dropout Voltage vs VBIAS
20
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
1.010
60
30701 G03
OUTPUT VOLTAGE (V)
90
70
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
IOUT = 5A
180 TJ = 25°C
DROPOUT VOLTAGE (mV)
DROPOUT VOLTAGE (mV)
200
VIN = VOUT(NOMINAL)
IOUT = 5A
120
80
30701 G02
30701 G01
150
VIN = VOUT(NOMINAL)
IOUT = 2.5A
10
ILOAD = 10mA
1.510
OUTPUT VOLTAGE (V)
90
Dropout Voltage vs Temperature
100
DROPOUT VOLTAGE (mV)
Dropout Voltage vs IOUT
DROPOUT VOLTAGE (mV)
DROPOUT VOLTAGE (mV)
150
1.204
1.200
1.196
1.505
1.500
1.495
1.192
1.490
1.188
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
1.485
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
0.992
0.990
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
30701 G07
30701 G08
30701 G09
Rev 0
6
For more information www.analog.com
LT3070-1
TYPICAL PERFORMANCE CHARACTERISTICS
Output Voltage (1.8V)
vs Temperature
GND PIN CURRENT (mA)
OUTPUT VOLTAGE (V)
1.806
1.802
1.798
1.794
1.790
2.0
1.5
1.0
VOUT = 1.8V, VBIAS = 3.3V
VOUT = 1.2V, VBIAS = 3.3V
VOUT = 0.8V, VBIAS = 2.5V
0.5
1.786
0
1.782
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
0
1
10
100
50
2.5
8
7
VOUT = 1.8V
VBIAS = 3.3V
6
VOUT = 0.8V
VBIAS = 2.5V
5
4
3
2
0
0
1
3
4
2
OUTPUT CURRENT (A)
30701 G13
VBIAS = 2.5V
ENABLE/DISABLE THRESHOLD (V)
ENABLE PIN THRESHOLD (V)
4.0
1.6
1.4
1.2
1.0
0.8
2.0
VBIAS RISING
1.5
1.0
VBIAS FALLING
0.5
EN PIN RISING
EN PIN FALLING
0.6
0.4
0.2
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
30701 G16
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
5
30701 G14
EN Pin Thresholds
1.8
30701 G12
1
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
2.0
594
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
BIAS Pin Undervoltage Lockout
Threshold
VIN = VOUT + 300mV
TJ = 25°C
9
BIAS PIN CURRENT (mA)
BIAS PIN CURRENT (µA)
VBIAS = 2.5V
350 VEN = 0V
150
598
BIAS Pin Current vs IOUT
400
200
600
30701 G11
BIAS Pin Current in Nap Mode
250
602
596
5
2
3
4
OUTPUT CURRENT (A)
30701 G10
300
CREF/BYP = 0.01µF
604
REF/BYP VOLTAGE (mV)
2.5
1.810
606
VIN = VOUT + 300mV
TJ = 25°C
UVLO THRESHOLD VOLTAGE (V)
1.814
3.0
ILOAD = 10mA
Enable Pin Threshold and
Hysteresis vs VBIAS
TJ = –55°C TO 125°C
3.5 TYPICAL HYSTERESIS = 150mV
3.0
PWRGD Threshold Voltage
1.00
VBIAS
2.5
MAX ENABLE
2.0
TYP ENABLE
1.5
MIN DISABLE
TYP DISABLE
1.0
0.5
0
30701 G15
PWRGD TRESHOLD VOLTAGE (V)
1.818
REF/BYP Pin Voltage
vs Temperature
GND Pin Current vs IOUT
2
2.5
3
4
3.5
BIAS VOLTAGE (V)
30701 G17
VBIAS = 2.5V
VOUT = 1V
0.95
VOUT RISING
0.90
0.85
VOUT FALLING
0.80
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
30701 G18
Rev 0
For more information www.analog.com
7
LT3070-1
TYPICAL PERFORMANCE CHARACTERISTICS
0.8
VBIAS = 2.5V
IPWRGD = 200µA
80
60
40
20
0.7
0.6
0.5
INPUT RISING
LOGIC LOW TO Hi-Z
INPUT FALLING
LOGIC Hi-Z TO LOW
0.4
0.3
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
0 25 50 75 100 125 150
TEMPERATURE (°C)
30701 G19
2.7
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
2.6
Logic Pin Input Current,
Low State
35
40
VLOGIC = VBIAS = 2.5V
CURRENT FLOWS INTO THE PIN
30
25
20
15
10
5
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
VBIAS = 2.5V
35 VLOGIC = 0V
CURRENT FLOWS OUT OF THE PIN
30
25
20
15
10
5
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
30701 G23
30701 G22
SENSE Pin Current
30701 G24
Current Limit vs Temperature
SENSE Pin Current
7.50
400
65
SENSE PIN CURRENT (µA)
VBIAS = 2.5V
60 VOUT = 0.8V
CURRENT FLOWS INTO SENSE
55
50
45
40
35
INPUT FALLING
LOGIC HIGH TO Hi-Z
30701 G21
LOGIC PIN INPUT CURRENT (µA)
40
VEN = VBIAS = 2.5V
1.0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
SENSE PIN CURRENT (µA)
INPUT RISING
LOGIC Hi-Z TO HIGH
Logic Pin Input Current,
High State
LOGIC PIN INPUT CURRENT (µA)
EN PIN LOGIC HIGH CURRENT (µA)
5.5
2.8
30701 G20
EN Pin Logic High Current
6.0
2.9
VBIAS = 3.3V
LOGIC Hi-Z TO HIGH THRESHOLD IS
RELATIVE TO VBIAS VOLTAGE
SEE APPLICATIONS INFORMATION
FOR MORE DETAILS
2.5
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
VBIAS = 3.3V
375 VOUT = 1.8V
CURRENT FLOWS INTO SENSE
350
7.25
VIN – VOUT(NOMINAL) = 300mV
7.00
CURRENT LIMIT (A)
0
–75 –50 –25
3.0
SEE APPLICATIONS INFORMATION
FOR MORE DETAILS
LOGIC INPUT THRESHOLD VOLTAGE (V)
PWRGD VOL vs Temperature
LOGIC INPUT THRESHOLD VOLTAGE (V)
PWRGD VOL VOLTAGE (mV)
100
Logic Input Threshold Voltages
Logic Hi-Z to High State Transitions
Logic Input Threshold Voltages
Logic Low to Hi-Z State Transitions
325
300
275
250
6.75
6.50
6.25
6.00
5.75
5.50
VOUT = 1.8V, VBIAS = 3.3V
VOUT = 1.2V, VBIAS = 3.3V
VOUT = 0.8V, VBIAS = 2.5V
30
225
5.25
25
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
200
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
5.00
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
30701 G25
30701 G26
30701 G27
Rev 0
8
For more information www.analog.com
LT3070-1
TYPICAL PERFORMANCE CHARACTERISTICS
BIAS Pin Ripple Rejection
VBIAS = 3.3V
TJ = 25°C
6
5
4
3
2
VOUT = 1.8V
VOUT = 1.2V
VOUT = 0.8V
0
0
80
70
60
50
40
30
20
10
0
0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
IN-TO-OUT VOLTAGE DIFFERENTIAL (V)
VBIAS = 2.5V + 500mVP-P
VBIAS = 2.7V + 500mVP-P
VBIAS = 3.3V + 500mVP-P
10
100
1k
10k 100k
FREQUENCY (Hz)
120
110
100
1M
90
80
50
40
COUT = 117µF
COUT = 16.9µF
100
1k
10k 100k
FREQUENCY (Hz)
100
90
0
10M
80
120
50mVP-P RIPPLE ON VIN
COUT = 16.9μF
VBIAS = 2.5V
RIPPLE AT f = 10kHz
TA = 25°C
110
100
90
80
50
40
70
60
50
40
RIPPLE AT f = 100kHz
60
40
30
10M
50mVP-P RIPPLE ON VIN
COUT = 16.9μF
VBIAS = 2.5V
TA = 25°C
RIPPLE AT f = 10kHz
RIPPLE AT f = 100kHz
RIPPLE AT f = 1MHz
10
0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2
AVERAGE INPUT/OUTPUT DIFFERENTIAL (V)
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2
AVERAGE INPUT/OUTPUT DIFFERENTIAL (V)
30701 G33
IN Pin Ripple Rejection
vs VIN – VOUT, 1V/2.5A
120
50mVP-P RIPPLE ON VIN
COUT = 117μF
VBIAS = 2.5V
TA = 25°C
110
100
90
RIPPLE AT f = 10kHz
RIPPLE AT f = 1MHz
RIPPLE AT f = 100kHz
80
70
RIPPLE AT f = 1MHz
40
RIPPLE AT f = 100kHz
20
20
10
10
0
0
30701 G35
RIPPLE AT f = 10kHz
50
10
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2
AVERAGE INPUT/OUTPUT DIFFERENTIAL (V)
50mVP-P RIPPLE ON VIN
COUT = 117μF
VBIAS = 2.5V
TA = 25°C
60
20
30701 G34
1M
20
RIPPLE AT f = 1MHz
30
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2
AVERAGE INPUT/OUTPUT DIFFERENTIAL (V)
1k
10k 100k
FREQUENCY (Hz)
50
30
RIPPLE AT f = 1MHz
100
70
IN Pin Ripple Rejection
vs VIN – VOUT, 1V/5A
RIPPLE AT f = 100kHz
10
30701 G32
PSRR (dB)
PSRR (dB)
90
10
60
30
100
50
20
80
70
110
60
IN Pin Ripple Rejection
vs VIN – VOUT, 1V/1A
110
VOUT = 1V
VIN = 1.3V + 50mVP-P RIPPLE
VBIAS = 2.5V
IOUT = 1A
120
50mVP-P RIPPLE ON VIN
COUT = 16.9μF
VBIAS = 2.5V
TA = 25°C
RIPPLE AT f = 10kHz
30701 G31
120
20
30701 G30
30
1M
COUT = 117µF
COUT = 16.9µF
30
IN Pin Ripple Rejection
vs VIN – VOUT, 1V/2.5A
70
40
VOUT = 1V
VIN = 1.3V + 50mVP-P RIPPLE
VBIAS = 2.5V
IOUT = 5A
10
40
0
10M
PSRR (dB)
60
PSRR (dB)
IN PIN RIPPLE REJECTION (dB)
70
0
50
IN Pin Ripple Rejection
vs VIN – VOUT, 1V/5A
80
10
60
30701 G29
IN Pin Ripple Rejection
20
70
10
30701 G28
30
80
PSRR (dB)
1
IN Pin Ripple Rejection
VIN = 1.3V
VOUT = 1V
IOUT = 5A
COUT = 10µF + 4.7µF + 2.2µF
90
BIAS PIN RIPPLE REJECTION (dB)
7
CURRENT LIMIT (A)
100
IN PIN RIPPLE REJECTION (dB)
Current Limit vs VIN – VOUT
8
0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2
AVERAGE INPUT/OUTPUT DIFFERENTIAL (V)
30701 G36
Rev 0
For more information www.analog.com
9
LT3070-1
TYPICAL PERFORMANCE CHARACTERISTICS
110
100
90
50mVP-P RIPPLE ON VIN
COUT = 117μF
VBIAS = 2.5V
TA = 25°C
80
PSRR (dB)
4.0
3.8
RIPPLE AT f = 10kHz
70
60
RIPPLE AT f = 1MHz
50
40
RIPPLE AT f = 100kHz
30
20
Minimum BIAS Voltage vs IOUT
VOUT = 1.8V
VOUT = 1.2V
VOUT = 0.8V
3.4
3.2
3.0
2.8
2.6
2.4
10
0
IOUT = 5A
3.6
MINIMUM BIAS VOLTAGE (V)
120
Minimum BIAS Voltage
vs Temperature
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2
AVERAGE INPUT/OUTPUT DIFFERENTIAL (V)
30701 G37
3.6
VIN = VOUT(NOMINAL) + 300mV
ΔVOUT = –1%, TJ = 25°C
VOUT = 1.8V
VOUT = 1.5V
VOUT = 1.2V
VOUT = 0.8V TO 1V
3.4
MINIMUM BIAS VOLTAGE (V)
IN Pin Ripple Rejection
vs VIN – VOUT, 1V/1A
3.2
3.0
2.8
2.6
2.4
2.2
2.2
2.0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
2.0
0
1
2
4
3
OUTPUT CURRENT (A)
30701 G39
30701 G38
Load Regulation
Minimum BIAS Voltage vs VOUT
IOUT = 5A
TJ = 25°C
3.0
LOAD REGULATION (mV)
MINIMUM BIAS VOLTAGE (V)
3.2
2.8
2.6
2.4
2.2
–2
–4
–6
–8
2.0
1.8
0.7
0.9
Bias Voltage Line Regulation
800
0
1.5
1.1
1.3
OUTPUT VOLTAGE (V)
1.7
BIAS VOLTAGE LINE REGULATION (µV)
3.4
VIN = VOUT(NOMINAL) + 300mV
VBIAS = 3.3V
ΔIOUT = 100mA TO 5A
VOUT = 0.8V
VOUT = 1.2V
VOUT = 1.8V
30701 G41
30701 G40
VBIAS = 2.2V TO 3.6V
700 VIN = 1.1V
VOUT = 0.8V
600 IOUT = 10mA
500
400
300
200
100
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
–10
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
1.9
5
30701 G42
Input Voltage Line Regulation
INPUT VOLTAGE LINE REGULATION (µV)
BIAS VOLTAGE LINE REGULATION (µV)
300
VBIAS = 3.25V TO 3.6V
300 VIN = 2.1V
VOUT = 1.8V
200 IOUT = 10mA
100
0
–100
–200
–300
–400
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
30701 G43
250
Input Voltage Line Regulation
300
VBIAS = 3.3V
VIN = 1.05V TO 2.7V
VOUT = 0.8V
IOUT = 10mA
INPUT VOLTAGE LINE REGULATION (µV)
Bias Voltage Line Regulation
400
200
150
100
50
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
30701 G44
250
VBIAS = 3.3V
VIN = 2.05V TO 2.7V
VOUT = 1.8V
IOUT = 10mA
200
150
100
50
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
30701 G45
Rev 0
10
For more information www.analog.com
LT3070-1
TYPICAL PERFORMANCE CHARACTERISTICS
0.1
0.01
0.001
100
80
VIN = VOUT(NOMINAL) + 300mV
70 VBIAS = 3.3V
COUT = 16.9µF
60 CREF/BYP = 10nF
10
100
1k
10k
FREQUENCY (Hz)
100k
80
50
40
30
20
10
0
0.01
10
1n
Input Voltage Line Transient
Response
10n
100n
1µ
REF/BYP CAPACITOR (F)
10µ
Bias Voltage Line Transient
Response
VOUT
10mV/DIV
VBIAS
200mV/DIV
VIN = 1.3V
VOUT = 1V
IOUT = 5A
COUT = 16.9µF
30701 G50
20µs/DIV
VIN = 1.3V
VBIAS = 2.5V
VOUT = 1V
IOUT = 5A
COUT = 16.9µF
20µs/DIV
30701 G51
VIOC Amplifier Output Current
vs Temperature
300
VBIAS = 2.5V
VIOC AMPLIFIER OUTPUT CURRENT (µA)
VIOC IN-TO-OUT SERVO VOLTAGE (mV)
340
30
LT30701 G48
VIOC Amplifier IN-to-OUT Servo
Voltage
350
40
0
0.1
1
OUTPUT CURRENT (A)
VIN
50mV/DIV
30701 G49
50
10
VOUT
1mV/DIV
1ms/DIV
60
30701 G47
Output Noise (10Hz to 100kHz)
VOUT = 1V
IOUT = 5A
COUT = 16.9µF
70
20
VOUT = 1.8V
VOUT = 1.2V
VOUT = 0.8V
30701 G46
VOUT
100µV/DIV
COUT = 16.9µF
VOUT = 0.8V
IL = 5A
TJ = 25°C
90
OUTPUT NOISE (uVRMS)
VBIAS = 2.5V
VOUT = 1V
IOUT = 5A
COUT = 16.9µF
CREF/BYP = 0.01µF
OUTPUT NOISE (µVRMS)
NOISE SPECTRAL DENSITY (µV/√Hz)
1.0
RMS Output Noise
vs CREF/BYP
RMS Output Noise
vs Output Current
Output Noise Spectral Density
330
320
310
300
290
280
270
260
250
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
275
IVIOC SOURCING
250
IVIOC SINKING
225
200
175
150
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
30701 G52
30701 G53
Rev 0
For more information www.analog.com
11
LT3070-1
TYPICAL PERFORMANCE CHARACTERISTICS
Transient Load Response
Transient Load Response
VOUT
50mV/DIV
AC-COUPLED
VOUT
50mV/DIV
AC-COUPLED
IOUT
2A/DIV
∆I = 500mA
TO 5A
IOUT
2A/DIV
∆I = 500mA
TO 5A
30701 G54
VOUT = 1V
20µs/DIV
COUT = 10µF + 4.7µF + 2.2µF
IOUT tRISE/tFALL = 100ns
VOUT = 1V
20µs/DIV
COUT = 117µF
IOUT tRISE/tFALL = 100ns
Transient Load Response
30701 G55
Transient Load Response
VOUT
50mV/DIV
AC-COUPLED
VOUT
50mV/DIV
AC-COUPLED
IOUT
2A/DIV
∆I = 500mA
TO 5A
IOUT
2A/DIV
∆I = 500mA
TO 5A
30701 G56
VOUT = 1V
20µs/DIV
COUT = 10µF + 4.7µF + 2.2µF
IOUT tRISE/tFALL = 1µs
VOUT = 1V
20µs/DIV
COUT = 117µF
IOUT tRISE/tFALL = 1µs
Output Voltage Start-Up Time
vs CREF/BYP
30701 G57
EN Start-Up Response
OUTPUT VOLTAGE START–UP TIME (ms)
100
10
TJ = 25°C
IL = 100mA
SETTLING TO 1%
IIN
100mA/DIV
VOUT
500mV/DIV
RL = 10Ω
VREF
500mV/DIV
CREF/BYP = 10nF
1
VEN
2V/DIV
0.1
0.01
100p
1n
10n
100n
REF/BYP CAPACITOR (F)
1µ
CIN = 330µF
COUT = 16.9µF
VOUT = 1V
400µs/DIV
30701 G59
LT30701 G58
Rev 0
12
For more information www.analog.com
LT3070-1
PIN FUNCTIONS
VIOC (Pin 1): Voltage for In-to-Out Control. The IC incorporates a unique tracking function to control a buck regulator
powering the LT3070-1’s input. The VIOC pin is the output
of this tracking function that drives the buck regulator to
maintain the LT3070-1’s input voltage at VOUT + 300mV.
This function maximizes efficiency and minimizes power
dissipation. See the Applications Information section for
more information on proper control of the buck regulator.
PWRGD (Pin 2): Power Good. The PWRGD pin is an opendrain NMOS output that actively pulls low if any one of
these fault modes is detected:
• VOUT is less than 90% of VOUT(NOMINAL) on the rising
edge of VOUT .
• VOUT drops below 85% of VOUT(NOMINAL) for more than
25µs.
• Junction temperature typically exceeds 145°C.
• VBIAS is less than its undervoltage lockout threshold.
• The OUT-to-IN reverse-current detector activates.
See the Applications Information section for more information on PWRGD fault modes.
REF/BYP (Pin 3): Reference Filter. The pin is the output
of the bandgap reference and has an impedance of approximately 19kΩ. This pin must not be externally loaded.
Bypassing the REF/BYP pin to GND with a capacitor
decreases output voltage noise and provides a soft-start
function to the reference. ADI recommends the use of a
high quality, low leakage capacitor. See the Applications
Information section for more information on noise and
output voltage margining considerations.
GND (Pins 4, 9-14, 20, 26, 29): Ground. The exposed pad
(Pin 29) of the QFN package is an electrical connection to
GND. To ensure proper electrical and thermal performance,
solder Pin 29 to the PCB ground and tie to all GND pins
of the package. These GND pins are fused to the internal
die attach paddle and the exposed pad to optimize heat
sinking and thermal resistance characteristics. See the Applications Information section for thermal considerations
and calculating junction temperature.
IN (Pins 5, 6, 7, 8): Input Supply. These pins supply
power to the high current pass transistor. Tie all IN pins
together for proper performance. The LT3070-1 requires
a bypass capacitor at IN to maintain stability and low input
impedance over frequency. A 47µF input bypass capacitor
suffices for most battery and power plane impedances.
Minimizing input trace inductance optimizes performance.
Applications that operate with low VIN-VOUT differential
voltages and that have large, fast load transients may require
much higher input capacitor requirements to prevent the
input supply from drooping and allowing the regulator to
enter dropout. See the Applications Information section
for more information on input capacitor requirements.
OUT (Pins 15, 16, 17, 18): Output. These pins supply
power to the load. Tie all OUT pins together for proper
performance. A minimum output capacitance of 15µF is
required for stability. ADI recommends low ESR, X5R or
X7R dielectric ceramic capacitors for best performance.
A parallel ceramic capacitor combination of 10µF + 4.7µF
+ 2.2µF or 15 1µF ceramic capacitors in parallel provide
excellent stability and load transient response. Large load
transient applications require larger output capacitors to
limit peak voltage transients. See the Applications Information section for more information on output capacitor
requirements.
SENSE (Pin 19): Kelvin Sense for OUT . The SENSE pin is
the inverting input to the error amplifier. Optimum regulation is obtained when the SENSE pin is connected to
the OUT pins of the regulator. In critical applications, the
resistance (RP) of PCB traces between the regulator and the
load cause small voltage drops, creating a load regulation
error at the point of load. Connecting the SENSE pin at
the load instead of directly to OUT eliminates this voltage
error. Figure 1 illustrates this Kelvin-Sense connection
method. Note that the voltage drop across the external
PCB traces adds to the dropout voltage of the regulator.
The SENSE pin input bias current depends on the selected
output voltage. SENSE pin input current varies from 50µA
typically at VOUT = 0.8V to 300µA typically at VOUT = 1.8V.
Rev 0
For more information www.analog.com
13
LT3070-1
PIN FUNCTIONS
+
VBIAS
EN
BIAS
SENSE
IN
VO2
+
OUT
LT3070-1
VO1
VIN
RP
PWRGD
VO0
LOAD
MARGSEL
MARGTOL
VIOC
REF/BYP
GND
RP
30701 F01
Figure 1. Kelvin Sense Connection
MARGSEL (Pin 21): Margining Enable and Polarity Selection. This three-state pin determines both the polarity
and the active state of the margining function. The logic
low threshold is less than 250mV referenced to GND and
enables negative voltage margining. The logic high threshold is greater than VBIAS – 250mV and enables positive
voltage margining. The voltage range between these two
logic thresholds as set by a window comparator defines
the logic Hi-Z state and disables the margining function.
MARGTOL (Pin 22): Margining Tolerance. This threestate pin selects the absolute value of margining (1%,
3% or 5%) if enabled by the MARGSEL input. The logic
low threshold is less than 250mV referenced to GND and
enables either ±1% change in VOUT depending on the state
of the MARGSEL pin. The logic high threshold is greater
than VBIAS – 250mV and enables either ±5% change in
VOUT depending on the state of the MARGSEL pin. The
voltage range between these two logic thresholds as set
by a window comparator defines the logic Hi-Z state and
enables either ±3% change in VOUT depending on the state
of the MARGSEL pin.
VO0, VO1 and VO2 (Pins 23, 24, 25): Output Voltage Select. These three-state pins combine to select a nominal
output voltage from 0.8V to 1.8V in increments of 50mV.
Output voltage is limited to 1.8V maximum by an internal
override of VO1 when VO2 = high. The input logic low
threshold is less than 250mV referenced to GND and the
logic high threshold is greater than VBIAS – 250mV. The
range between these two thresholds as set by a window
comparator defines the logic Hi-Z state. See Table 1 in the
Applications Information section that defines the VO2, VO1
and VO0 settings versus VOUT .
BIAS (Pin 27): Bias Supply. This pin supplies current to
the internal control circuitry and the output stage driving
the pass transistor. The LT3070-1 requires a minimum
2.2µF bypass capacitor for stability and proper operation.
To ensure proper operation, the BIAS voltage must satisfy
the following conditions: 2.2V ≤ VBIAS ≤ 3.6V and VBIAS ≥
(1.25 • VOUT + 1V). For VOUT ≤ 0.95V, the minimum BIAS
voltage is limited to 2.2V.
EN (Pin 28): Enable. This pin enables/disables the reference
output and output power device. The internal reference and
all support functions are active if VBIAS is above its UVLO
threshold. Pulling EN low disables the REF/BYP pin current
and the output pass transistor, putting the LT3070-1 into
a low power nap mode. The maximum rising EN threshold
is ratioed to 0.56 % of VBIAS and the minimum falling EN
threshold is 0.36 % of VBIAS. Drive the EN pin with either
a digital logic port or an open-collector NPN or an opendrain NMOS terminated with a pull-up resistor to VBIAS.
The pull-up resistor must be less than 35k to meet the VIH
condition of the EN pin. If unused, connect EN to BIAS.
Rev 0
14
For more information www.analog.com
LT3070-1
BLOCK DIAGRAM
27
BIAS
IN
5-8
UVLO AND
THERMAL
SHUTDOWN
+
ISENSE
REF/BYP
–
+
EAMP
BUF
–
OUT
15-18
LDO CORE
SENSE
DETECT
VIOC
+
–
1
PWRGD
19
2
VOUT(NOM) + 300mV
VREF
GND
4,9-14,20,26,29
REF/BYP
600mV
3
PROGRAM CONTROL
EN
28
VO2 VO1 VO0 MARGSEL MARGTOL
25
24
23
21
22
30701 BD
LOGIC HIGH STATE
EN
100k
TO INTERNAL ENABLE
SEE ENABLE THRESHOLD
CURVE
VBIAS – 0.25V
+
LOGIC Hi-Z STATE
VBIAS
VO2, VO1, VO0
MARGSEL OR
MARGTOL
–
100k
VBIAS – 0.9V
100k
0.75V
+
–
+
–
TO LOGIC
HIGH IF IN > VBIAS – 0.25V
HIGH IF IN < VBIAS – 0.9V
AND IN > 0.75V
HIGH IF IN < 0.25V
LOGIC LOW STATE
–
0.25V
+
Rev 0
For more information www.analog.com
15
LT3070-1
APPLICATIONS INFORMATION
Introduction
Current generation FPGA and ASIC processors place
stringent demands on the power supplies that power the
core, I/O and transceiver channels. These microprocessors
may cycle load current from near zero to amps in tens of
nanoseconds. Output voltage specifications, especially in
the 1V range, require tight tolerances including transient
response as part of the requirement. Some ASIC processors
require only a single output voltage from which the core
and I/O circuitry operate. Some high performance FPGA
processors require separate power supply voltages for the
processor core, the I/O, and the transceivers. Often, these
supply voltages must be low noise and high bandwidth
to achieve the lowest bit-error rates. These requirements
mandate the need for very accurate, low noise, high current, very high speed regulator circuits that operate at low
input and output voltages.
The LT3070-1 is a low voltage, UltraFast transient response
linear regulator. The device supplies up to 5A of output
current with a typical dropout voltage of 85mV. A 0.01µF
reference bypass capacitor decreases output voltage noise
to 25µVRMS (BW = 10Hz to 100kHz). The LT3070-1’s high
bandwidth provides UltraFast transient response using low
ESR ceramic output capacitors (15µF minimum), saving
bulk capacitance, PCB area and cost.
The LT3070-1’s features permit state-of-the-art linear
regulator performance. The LT3070-1 is ideal for high
performance FPGAs, microprocessors, sensitive communication supplies, and high current logic applications
that also operate over low input and output voltages.
Output voltage for the LT3070-1 is digitally selectable in
50mV increments over a 0.8V to 1.8V range. A margining
function allows the user to adjust system output voltage
in increments of ±1%, ±3% or ±5%.
The IC incorporates a unique tracking function, which if
enabled by the user, controls an upsteam regulator powering the LT3070-1’s input (see Figure 7). This tracking
function drives the buck regulator to maintain the LT30701’s input voltage to VOUT + 300mV. This input-to-output
voltage control allows the user to change the regulator
output voltage, and have the switching regulator powering the LT3070-1’s input to track to the optimum input
voltage with no component changes.
16
This combines the efficiency of a switching regulator
with superior linear regulator response. It also permits
thermal management of the system even with a maximum
5A output load.
LT3070-1 internal protection includes input undervoltage
lockout (UVLO), reverse-current protection, precision current limiting with power foldback and thermal shutdown.
The LT3070-1 regulator is available in a thermally enhanced
28-lead, 4mm × 5mm QFN package.
The LT3070-1’s architecture drives an internal N-channel
power MOSFET as a source follower. This configuration
permits a user to obtain an extremely low dropout, UltraFast
transient response regulator with excellent high frequency
PSRR performance. The LT3070-1 achieves superior
regulator bandwidth and transient load performance by
eliminating expensive bulk tantalum or electrolytic capacitors in the most modern and demanding microprocessor
applications. Users realize significant cost savings as all
additional bulk capacitance is removed. The additional
savings of insertion cost, purchasing/inventory cost and
board space are readily apparent. Precision incremental
output voltage control accommodates legacy and future
microprocessor power supply voltages.
Output capacitor networks simplify to direct parallel combinations of ceramic capacitors. Often, the high frequency
ceramic decoupling capacitors required by these various
FPGA and ASIC processors are sufficient to stabilize the
system (see Stability and Output Capacitance section). This
regulator design provides ample bandwidth and responds
to transient load changes in a few hundred nanoseconds
versus regulators that respond in many microseconds.
The LT3070-1 also incorporates precision current limiting,
enable/disable control of output voltage and integrated
overvoltage and thermal shutdown protection. The LT30701’s unique design combines the benefits of low dropout
voltage, high functional integration, precision performance
and UltraFast transient response, as well as providing
significant cost savings on the output capacitance needed
in fast load transient applications.
As lower voltage applications become increasingly prevalent with higher frequency switching power supplies, the
LT3070-1 offers superior regulation and an appreciable
For more information www.analog.com
Rev 0
LT3070-1
APPLICATIONS INFORMATION
component cost savings. The LT3070-1 steps to the next
level of performance for the latest generation FPGAs, DSPs
and microprocessors. The simple versatility and benefits
derived from these circuits exceed the power supply needs
of today’s high performance microprocessors.
Programming Output Voltage
Three tri-level input pins, VO2, VO1 and VO0, select the
value of output voltage. Table 1 illustrates the 3-bit digital
word to output voltage resulting from setting these pins
high, low or allowing them to float.
These pins may be tied high or low by either pin-strapping
them to VBIAS or driving them with digital ports. Pins that
float may either actually float or require logic that has
Hi-Z output capability. This allows output voltage to be
dynamically changed if necessary.
Output voltage is selectable from a minimum of 0.8V to
a maximum of 1.8V in increments of 50mV. The MSB,
VO2, sets the pedestal voltage, and the LSB’s, VO1 and
VO0 increment VOUT .
Output voltage is limited to 1.8V maximum by an internal
override of VO1 (default to low) when VO2 = high.
Table 1. VO2 to VO0 Settings vs Output Voltage
VO2
VO1
VO0
VOUT(NOM)
VO2
VO1
VO0
VOUT(NOM)
0
0
0
0.80V
Z
0
1
1.35V
0
0
Z
0.85V
Z
Z
0
1.40V
0
0
1
0.90V
Z
Z
Z
1.45V
0
Z
0
0.95V
Z
Z
1
1.50V
0
Z
Z
1.00V
Z
1
0
1.55V
0
Z
1
1.05V
Z
1
Z
1.60V
0
1
0
1.10V
Z
1
1
1.65V
0
1
Z
1.15V
1
X
0
1.70V
0
1
1
1.20V
1
X
Z
1.75V
Z
0
0
1.25V
1
X
1
1.80V
Z
0
Z
1.30V
X = Don’t Care, 0 = Low, Z = Float, 1 = High
The input logic low threshold is less than 250mV referenced to GND and the logic high threshold is greater than
VBIAS – 250mV. The range between these two thresholds
as set by a window comparator defines the logic Hi-Z state.
REF/BYP—Voltage Reference
This pin is the buffered output of the internal bandgap
reference and has an output impedance of ≅19kΩ. The
design includes an internal compensation pole at fC =
4kHz. A 10nF REF/BYP capacitor to GND creates a lowpass pole at fLP = 840Hz. The 10nF capacitor decreases
reference voltage noise to about 10µVRMS and soft-starts
the reference. The LT3070-1 soft-starts the reference
voltage when the EN pin is toggled from low to high. In
comparison, the LT3070 soft-starts only when turning
the BIAS supply voltage on. Output voltage noise is the
RMS sum of the reference voltage noise in addition to the
amplifier noise. Curves for start-up time and output noise
vs REF/BYP capacitance appear in the Typical Performance
Characteristics section.
The REF/BYP pin must not be DC loaded by anything except
for applications that parallel other LT3070-1 regulators for
higher output currents. Consult the Applications Section
on Paralleling for further details.
Output Voltage Margining
Two tri-level input pins, MARGSEL (polarity) and MARGTOL
(scale), select the polarity and amount of output voltage
margining. Margining is programmable in increments of
±1%, ±3% and ±5%. Margining is internally implemented
as a scaling of the reference voltage.
Table 2 illustrates the 2-bit digital word to output voltage
margining resulting from setting these pins high, low or
allowing them to float.
These pins may be set high or low by either pin-strapping
them to VBIAS or driving them with digital ports. Pins that
float may either actually float or require logic that has
“Hi-Z” output capability. This allows output voltage to be
dynamically margined if necessary.
The MARGSEL pin determines both the polarity and the active state of the margining function. The logic low threshold
is less than 250mV referenced to GND and enables negative
voltage margining. The logic high threshold is greater than
VBIAS – 250mV and enables positive voltage margining.
The voltage range between these two logic thresholds as
set by a window comparator defines the logic Hi-Z state
and disables the margining function.
Rev 0
For more information www.analog.com
17
LT3070-1
APPLICATIONS INFORMATION
The MARGTOL pin selects the absolute value of margining (1%, 3% or 5%) if enabled by the MARGSEL input.
The logic low threshold is less than 250mV referenced to
GND and enables either ±1% change in VOUT depending
on the state of the MARGSEL pin. The logic high threshold
is greater than VBIAS – 250mV and enables either ±5%
change in VOUT depending on the state of the MARGSEL
pin. The voltage range between these two logic thresholds
as set by a window comparator defines the logic Hi-Z state
and enables either ±3% change in VOUT depending on the
state of the MARGSEL pin.
Table 2. Programming Margining
MARGSEL
0
0
0
Z
Z
Z
1
1
1
MARGTOL
0
Z
1
0
Z
1
0
Z
1
% OF VOUT(NOM)
–1
–3
–5
0
0
0
1
3
5
Enable Function—Turning On and Off
The EN pin enables/disables the reference output and output
power device. The LT3070-1's support functions remain
active if VBIAS is above its UVLO threshold. Pulling the EN
pin low puts the LT3070-1 into nap mode. In nap mode,
the output is disabled and quiescent current decreases.
Drive the EN pin with either a digital logic port or an opencollector NPN or an open-drain NMOS terminated with
a pull-up resistor to VBIAS. The pull-up resistor must be
less than 35k to meet the VIH condition of the EN pin. If
unused, connect EN to BIAS.
Input Undervoltage Lockout on BIAS Pin
An internal undervoltage lockout (UVLO) comparator
monitors the BIAS supply voltage. If VBIAS drops below
the UVLO threshold, all functions shut down, the pass
transistor is gated off and output current falls to zero. The
typical BIAS pin UVLO threshold is 1.55V on the rising
edge of VBIAS. The UVLO circuit incorporates about 150mV
of hysteresis on the falling edge of VBIAS.
High Efficiency Linear Regulator—Input-to-Output
Voltage Control
The VIOC (voltage input-to-output control) pin is a function to control a switching regulator and facilitate a design
solution that maximizes system efficiency at high load currents and still provides low dropout voltage performance.
The VIOC pin is the output of an integrated transconductance amplifier that sources and sinks about 250µA
of current. It typically regulates the output of most LTC®
switching regulators or LTM® power modules, by sinking
current from the ITH compensation node. The VIOC function controls a buck regulator powering the LT3070-1’s
input by maintaining the LT3070-1’s input voltage to VOUT
+ 300mV. This 300mV VIN-VOUT differential voltage is
chosen to provide fast transient response and good high
frequency PSRR while minimizing power dissipation and
maximizing efficiency. For example, 1.5V to 1.2V conversion and 1.3V to 1V conversion yield 1.5W maximum
power dissipation at 5A full output current.
Figure 2 depicts that the switcher’s feedback resistor network sets the maximum switching regulator output voltage if the linear regulator is disabled. However, once the
LT3070-1 is enabled, the VIOC feedback loop decreases the
switching regulator output voltage back to VOUT + 300mV.
Using the VIOC function creates a feedback loop between
the LT3070-1 and the switching regulator. As such, the
feedback loop must be frequency compensated for stability. Fortunately, the connection of VIOC to many ADI
switching regulator ITH pins represents a high impedance
characteristic which is the optimum circuit node to frequency compensate the feedback loop. Figure 2 illustrates
the typical frequency compensation network used at the
VIOC node to GND.
The VIOC amplifier characteristics are:
gm = 3.2mS, IOUT = ±250µA, BW = 10MHz.
If the VIOC function is not used, terminate the VIOC pin to
GND with a small capacitor (1000pF) to prevent oscillations.
Rev 0
18
For more information www.analog.com
LT3070-1
APPLICATIONS INFORMATION
LT3070-1
IN
OUT
SWITCHING REGULATOR
REF
+
–
LOAD
–
+
PWM
FB
VOUT +
VREF 300mV
VIOC
REFERENCE
ITH
30701 F02
Figure 2. VIOC Control Block Diagram
PWRGD—Power Good
PWRGD pin is an open-drain NMOS digital output that
actively pulls low if any one of these fault modes is detected:
• VOUT is less than 90% of VOUT(NOMINAL) on the rising
edge of VOUT .
• VOUT drops below 85% of VOUT(NOMINAL) for more than
25µs.
• VBIAS is less than its undervoltage lockout threshold.
• The OUT-to-IN reverse-current detector activates.
• Junction temperature exceeds 145°C typically.*
*The junction temperature detector is an early warning
indicator that trips approximately 20°C before thermal
shutdown engages.
Stability and Output Capacitance
The LT3070-1’s feedback loop requires an output capacitor for stability. Choose COUT carefully and mount it in
close proximity to the LT3070-1’s OUT and GND pins.
Include wide routing planes for OUT and GND to minimize
inductance. If possible, mount the regulator immediately
adjacent to the application load to minimize distributed
inductance for optimal load transient performance. Pointof-Load applications present the best case layout scenario
for extracting full LT3070-1 performance.
Low ESR, X5R or X7R ceramic chip capacitors are the
ADI recommended choice for stabilizing the LT3070-1.
Additional bulk capacitors distributed beyond the immediate decoupling capacitors are acceptable as their parasitic
ESL and ESR, combined with the distributed PCB inductance isolates them from the primary compensation pole
provided by the local surface mount ceramic capacitors.
The LT3070-1 requires a minimum output capacitance
of 15µF for stability. ADI strongly recommends that the
output capacitor network consist of several low value
ceramic capacitors in parallel.
Why Do Multiple, Small-Value Output Capacitors
Connected in Parallel Work Better?
The LT3070-1’s unity-gain bandwidth with COUT of 15µF is
about 1MHz at its full-load current of 5A. Surface mounted
MLCC capacitors have a self-resonance frequency of
fR = 1/(2π√LC), which must be pushed to a frequency higher
than the regulator bandwidth. Standard MLCC capacitors
are acceptable. To keep the resonant frequency greater
than 1MHz, the product 1/(2π√LC) must be greater than
1MHz. At this bandwidth, PCB vias can add significant
inductance, thus the fundamental decoupling capacitors
must be mounted on the same plane as the LT3070-1.
Typical 0603 or 0805 case-size capacitors have an ESL of
~800pH and PCB mounting can contribute up to ~200pH.
Thus, it becomes necessary to reduce the parasitic inductance by using a parallel capacitor combination. A
Rev 0
For more information www.analog.com
19
LT3070-1
APPLICATIONS INFORMATION
suitable methodology must control this paralleling as
capacitors with the same self-resonant frequency, fR, will
form a tank circuit that can induce ringing of their own
accord. Small amounts of ESR (5mΩ to 20mΩ) have some
benefit in dampening the resonant loop, but higher ESRs
degrade the capacitor response to transient load steps
with rise/fall times less than 1µs. The most area efficient
parallel capacitor combination is a graduated 4/2/1 scale
of fR of the same case size. Under these conditions, the
individual ESLs are relatively uniform, and the resonance
peaks are deconstructively spread beyond the regulator
bandwidth. The recommended parallel combination that
approximates 15µF is 10µF + 4.7µF + 2.2µF. Capacitors
with case sizes larger than 0805 have higher ESL and
lower ESR (