BLM10D3740-35ABZ

BLM10D3740-35AB LDMOS 3-stage integrated Doherty MMIC Rev. 1 — 14 December 2020 Product data sheet 1. Product profile 1.1 General description The BLM10D3740-35AB is a 3-stage fully integrated asymmetrical Doherty MMIC solution using Ampleon’s state of the art LDMOS technology. The carrier and peaking device, input splitter, output combiner and pre-match are integrated in a single package. This multiband device is perfectly suited as a final stage for small cells and massive MIMO applications in the frequency range from 3700 MHz to 4000 MHz. Available in PQFN outline. Table 1. Application performance Typical RF performance at Tcase = 25 C; IDq = 44 mA (carrier); VGSq(peaking) = VGSq(carrier)  0.5 V. Test signal: 1-carrier LTE 20 MHz; PAR = 7.6 dB. Test signal single carrier LTE f VDS PL(AV) Gp D (MHz) (V) (W) (dB) (%) 3900 28 5 33 39 1.2 Features and benefits          Integrated input splitter Integrated output combiner 30  output impedance thanks to integrated pre-match Very high efficiency thanks to asymmetry Designed for wideband operation (frequency 3700 MHz to 4000 MHz) Independent control of carrier and peaking bias Integrated ESD protection Source impedance 50 ; high power gain For RoHS compliance see the product details on the Ampleon website 1.3 Applications  RF power MMIC for multi-carrier and multi-standard 5G base stations in the 3700 MHz to 4000 MHz frequency range BLM10D3740-35AB LDMOS 3-stage integrated Doherty MMIC 2. Pinning information 2.1 Pinning pin 1 index RF_OUT VDS2 1 20 19 18 17 16 15 VDS2 13 n.c. VGS(carr) 4 12 VGS(peak) 5 6 7 8 11 9 10 GND VDS1 3 RF_IN 14 n.c. VDS1 2 n.c. GND n.c. VGS(carr) VGS(peak) amp00887 Transparent top view The exposed backside of the package is the ground terminal of the device. Fig 1. Pin configuration 2.2 Pin description Table 2. BLM10D3740-35AB Product data sheet Pin description Symbol Pin Description VDS2 1 drain-source voltage of final stages n.c. 2 not connected n.c. 3 not connected VGS(carr) 4 gate-source voltage of carrier VGS(peak) 5 gate-source voltage of peaking VDS1 6 drain-source voltage of driver stages GND 7 RF ground RF_IN 8 RF input GND 9 RF ground VDS1 10 drain-source voltage of driver stages VGS(peak) 11 gate-source voltage of peaking VGS(carr) 12 gate-source voltage of carrier n.c. 13 not connected n.c. 14 not connected VDS2 15 drain-source voltage of final stages RF_OUT 16 RF output RF_OUT 17 RF output RF_OUT 18 RF output RF_OUT 19 RF output RF_OUT 20 RF output GND flange RF ground All information provided in this document is subject to legal disclaimers. Rev. 1 — 14 December 2020 © Ampleon Netherlands B.V. 2021. All rights reserved. 2 of 13 BLM10D3740-35AB LDMOS 3-stage integrated Doherty MMIC 3. Ordering information Table 3. Ordering information Type number Package BLM10D3740-35AB Name Description Version PQFN20 plastic thermal enhanced quad flat package; no leads; 20 terminals; body 8.0 x 8.0 x 2.1 mm SOT1462-1 4. Block diagram VGS(peak) Bias peak VDS1 RF_IN VGS(carr) RF_OUT Bias carr amp00888 Fig 2. Block diagram 5. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter VDS Min Max Unit drain-source voltage - 65 V VGS gate-source voltage 0.5 +13 V Tstg storage temperature 65 +150 C Tj junction temperature - 200 C [1] Conditions [1] Continuous use at maximum temperature will affect the reliability. For details refer to the online MTF calculator. 6. Thermal characteristics Table 5. Thermal characteristics Symbol Parameter Rth(j-c) [1] BLM10D3740-35AB Product data sheet Conditions Value Unit thermal resistance from junction to case Tcase = 90 C; PL = 2 W [1] 4 K/W Tcase = 90 C; PL = 5 W [1] 3.2 K/W When operated with a 1-carrier W-CDMA with PAR = 7.6 dB. All information provided in this document is subject to legal disclaimers. Rev. 1 — 14 December 2020 © Ampleon Netherlands B.V. 2021. All rights reserved. 3 of 13 BLM10D3740-35AB LDMOS 3-stage integrated Doherty MMIC 7. Characteristics Table 6. DC characteristics Tcase = 25 C. Symbol Parameter Conditions Min Typ Max Unit Carrier VGSq gate-source quiescent voltage VDS = 28 V; ID = 42 mA 1.65 2.0 2.6 V IGSS gate leakage current VGS = 1 V; VDS = 0 V - - 140 nA gate leakage current VGS = 1 V; VDS = 0 V - - 140 nA VGS = 0 V; VDS = 28 V - - 1.4 A VGS = 0 V; VDS = 28 V - - 1.4 A Peaking IGSS Final stages IDSS drain leakage current Driver stages IDSS drain leakage current Table 7. RF Characteristics Typical RF performance at Tcase = 25 C; VDS = 28 V; IDq = 42 mA (carrier); VGSq(peaking) = VGSq(carrier)  0.5 V; PL(AV) = 5 W; f = 3850 MHz measured in an Ampleon production device interface board. Symbol Parameter Conditions Min Typ Max Unit 32.2 34.2 36.4 dB Test signal: single carrier pulsed CW [1] Gp power gain PL = 5 W (37 dBm) D drain efficiency PL = 5 W (37 dBm) 34 41 - % PL = PL(3dB) 41 47 - % - 10 dB RLin input return loss - PL(3dB) output power at 3 dB gain compression 44.7 45.2 - [1] BLM10D3740-35AB Product data sheet dBm Pulsed CW power sweep measurement ( = 10 %, tp = 100 s). All information provided in this document is subject to legal disclaimers. Rev. 1 — 14 December 2020 © Ampleon Netherlands B.V. 2021. All rights reserved. 4 of 13 BLM10D3740-35AB LDMOS 3-stage integrated Doherty MMIC 8. Application information Table 8. Typical performance Tcase = 25 C; VDS = 28 V; IDq = 44 mA (carrier); VGSq(peaking) = VGSq(carrier)  0.5 V. Test signal: 1-carrier LTE; PAR = 7.6 dB at 0.01 % probability CCDF; unless otherwise specified, typical performance in an Ampleon f = 3700 MHz to 4000 MHz frequency band application circuit. Symbol Parameter Conditions PL(3dB) output power at 3 dB gain compression f = 3900 MHz Min Typ Max Unit [1] - 45.4 - dBm [2] - -26 -  s21/s21(norm) normalized phase response at 3 dB compression point; f = 3900 MHz D drain efficiency 8 dB OBO (PL(AV) = 37 dBm); f = 3900 MHz - 39 - % Gp power gain PL(AV) = 37 dBm; f = 3900 MHz - 33.1 - dB Bvideo video bandwidth PL(AV) = 37 dBm; 2-tone CW; f = 3800 MHz - 420 - MHz Gflat gain flatness PL(AV) = 37 dBm; f = 3700 MHz to 4000 MHz - 1.9 - dB ACPR20M adjacent channel power ratio (20 MHz) PL(AV) = 37 dBm; f = 3900 MHz - -31 - dBc G/T gain variation with temperature f = 3900 MHz [3] - 0.07 - dB/C PL(3dB)/T output power at 3 dB gain compression f = 3900 MHz variation with temperature [1] - 0.016 - K Rollett stability factor [3] - >1 Tcase = 30 C; f = 0.1 GHz to 6.1 GHz [1] Pulsed CW power sweep measurement ( = 10 %, tp = 100 s). [2] 25 ms CW power sweep measurement. [3] S-parameters. BLM10D3740-35AB Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 14 December 2020 dBm/C - © Ampleon Netherlands B.V. 2021. All rights reserved. 5 of 13 BLM10D3740-35AB LDMOS 3-stage integrated Doherty MMIC 40 mm T1 T2 C9 C1 J1 C3 J2 C4 C10 40 mm C5 C2 C8 C7 C11 C6 T3 T4 amp01548 Printed-Circuit Board (PCB): Rogers 4350; thickness = 0.508 mm. Fig 3. Component layout Table 9. Demo test circuit list of components See Figure 3 for component layout. Component Description Value Remarks C1, C2 multilayer ceramic chip capacitor 10 F, 6.3 V Murata: GRM21BR60J106KE01L C3, C4, C5, C6 multilayer ceramic chip capacitor 10 F, 50 V Murata: GRM31CR61H106KA12L C7, C8 multilayer ceramic chip capacitor 4.7 F, 6.3 V Murata: GRM155R60J475ME47D C9 multilayer ceramic chip capacitor 3.3 pF  0.1 % Murata: GQM1875C2E3R3BB12 C10 multilayer ceramic chip capacitor 3 pF  0.1 % Murata: GQM1875C2E3R0BB12 C11 multilayer ceramic chip capacitor 3 pF  0.1 % Murata: GQM1875C2E3R0BB12 J1 SMA Coaxial panel connector male Huber & Suhner: 13_SMA-50-0-2/111_N J2 SMA Coaxial panel connector female Huber & Suhner: 23_SMA-50-0-2/111_N T1, T2, T3, T4 PCB Terminal BLM10D3740-35AB Product data sheet 6.35 mm  0.81 mm, 4.1 mm TE connectivity All information provided in this document is subject to legal disclaimers. Rev. 1 — 14 December 2020 © Ampleon Netherlands B.V. 2021. All rights reserved. 6 of 13 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx BLM10D3740-35AB Product data sheet VDS T2 GND C3 4 3 n.c. 5 VDS2 VDS1 VGS(carr) C1 n.c. J1 VGS(peak) C9 C4 2 1 RF_OUT 6 J2 20 GND 7 19 RF_IN 8 18 GND 9 17 T3 VGS(peak) C7 C8 n.c. VDS2 C2 16 11 12 13 14 15 n.c. 10 VGS(carr) VDS1 VGS(peak) Rev. 1 — 14 December 2020 RF_OUT RF_OUT RF_OUT C10 RF_OUT C5 C11 C6 T4 7 of 13 © Ampleon Netherlands B.V. 2021. All rights reserved. Fig 4. Electrical schematic amp01549 BLM10D3740-35AB VGS(carr) LDMOS 3-stage integrated Doherty MMIC All information provided in this document is subject to legal disclaimers. T1 BLM10D3740-35AB LDMOS 3-stage integrated Doherty MMIC 8.1 Ruggedness in a Doherty operation The BLM10D3740-35AB is capable of withstanding a load mismatch corresponding to VSWR = 10 : 1 through all phases under the following conditions: VDS = 32 V; IDq = 45 mA (carrier); VGSq(peaking) = VGSq(carrier)  0.5 V; Pi corresponding to PL(3dB)  5 dB under ZS = 50  load; f = 3800 MHz (1-carrier W-CDMA; PAR = 9.9 dB); Tcase = 25 C. 8.2 Impedance information Table 10. Typical impedance for optimum Doherty operation Measured load-pull data; test signal: pulsed CW; Tcase = 25 C; VDS = 28 V; IDq = 42 mA (carrier); VGSq(peaking) = VGSq(carrier)  0.5 V; tp = 100 s;  = 10 %. tuned for optimum Doherty operation BLM10D3740-35AB Product data sheet f ZL PL(3dB) Gp(max) add [1] add [2] (MHz) () (dBm) (dB) (%) (%) 3600 28.06  j2.10 45.90 34.41 48.24 39.00 3700 23.04  j5.66 45.88 35.68 49.89 42.17 3800 22.77  j7.56 45.82 35.98 51.62 43.40 3900 22.76  j7.54 45.61 35.02 52.61 42.71 4000 24.82  j5.25 45.26 32.87 51.26 38.20 4100 19.20  j4.72 44.79 29.92 49.13 32.16 [1] at PL(3dB). [2] at 37 dBm. All information provided in this document is subject to legal disclaimers. Rev. 1 — 14 December 2020 © Ampleon Netherlands B.V. 2021. All rights reserved. 8 of 13 BLM10D3740-35AB LDMOS 3-stage integrated Doherty MMIC 9. Package outline PQFN20: plastic thermal enhanced quad flat package; no leads; 20 terminals; body 8.0 x 8.0 x 2.1 mm terminal 1 index area D B SOT1462-1 A E A A1 C detail X e1 v w b e A B C C C y1 C k1 6 y 10 L 5 11 e e2 Eh 1 15 k terminal 1 index area 20 16 X Dh 0 10 mm scale Dimensions Unit mm A(1) A1 b C D(1) max 2.20 0.05 0.60 8.1 nom 2.10 0.50 0.508 8.0 7.9 min 2.00 0.00 0.40 Dh E(1) 4.72 4.62 4.52 8.1 8.0 7.9 Eh e 4.72 4.62 1.15 4.52 e1 e2 4.6 4.6 k 0.99 k1 L v w y y1 0.1 0.05 0.1 0.1 0.99 0.8 0.7 0.6 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. Outline version References IEC JEDEC JEITA European projection Issue date 15-10-12 17-06-23 SOT1462-1 Fig 5. sot1462-1_po Package outline SOT1462-1 (PQFN20) BLM10D3740-35AB Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 14 December 2020 © Ampleon Netherlands B.V. 2021. All rights reserved. 9 of 13 BLM10D3740-35AB LDMOS 3-stage integrated Doherty MMIC 10. Handling information CAUTION This device is sensitive to ElectroStatic Discharge (ESD). Observe precautions for handling electrostatic sensitive devices. Such precautions are described in the ANSI/ESD S20.20, IEC/ST 61340-5, JESD625-A or equivalent standards. Table 11. ESD sensitivity ESD model Class Charged Device Model (CDM); According to ANSI/ESDA/JEDEC standard JS-002 C2A [1] Human Body Model (HBM); According to ANSI/ESDA/JEDEC standard JS-001 1B [2] [1] CDM classification C2A is granted to any part that passes after exposure to an ESD pulse of 500 V. [2] HBM classification 1B is granted to any part that passes after exposure to an ESD pulse of 500 V. 11. Abbreviations Table 12. Abbreviations Acronym Description CCDF Complementary Cumulative Distribution Function CW Continuous Wave ESD ElectroStatic Discharge LDMOS Laterally Diffused Metal Oxide Semiconductor LTE Long Term Evolution MMIC Monolithic Microwave Integrated Circuit MIMO Multiple Input Multiple Output MTF Median Time to Failure OBO Output Back Off PAR Peak-to-Average Ratio RoHS Restriction of Hazardous Substances VSWR Voltage Standing Wave Ratio W-CDMA Wideband Code Division Multiple Access 12. Revision history Table 13. Revision history Document ID Release date Data sheet status Change notice Supersedes BLM10D3740-35AB v.1 20201214 Product data sheet - - BLM10D3740-35AB Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 14 December 2020 © Ampleon Netherlands B.V. 2021. All rights reserved. 10 of 13 BLM10D3740-35AB LDMOS 3-stage integrated Doherty MMIC 13. Legal information 13.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.ampleon.com. 13.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Ampleon does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Ampleon sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between Ampleon and its customer, unless Ampleon and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the Ampleon product is deemed to offer functions and qualities beyond those described in the Product data sheet. 13.3 Disclaimers Maturity — The information in this document can only be regarded as final once the relevant product(s) has passed the Release Gate in Ampleon's release process. Prior to such release this document should be regarded as a draft version. Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, Ampleon does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Ampleon takes no responsibility for the content in this document if provided by an information source outside of Ampleon. In no event shall Ampleon be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, Ampleon’s aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Ampleon. BLM10D3740-35AB Product data sheet Right to make changes — Ampleon reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — Ampleon products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an Ampleon product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Ampleon and its suppliers accept no liability for inclusion and/or use of Ampleon products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. Ampleon makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using Ampleon products, and Ampleon accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Ampleon product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. Ampleon does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Ampleon products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). Ampleon does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — Ampleon products are sold subject to the general terms and conditions of commercial sale, as published at http://www.ampleon.com/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. Ampleon hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of Ampleon products by customer. All information provided in this document is subject to legal disclaimers. Rev. 1 — 14 December 2020 © Ampleon Netherlands B.V. 2021. All rights reserved. 11 of 13 BLM10D3740-35AB LDMOS 3-stage integrated Doherty MMIC No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific Ampleon product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. Ampleon accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without Ampleon’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond Ampleon’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies Ampleon for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond Ampleon’s standard warranty and Ampleon’s product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 13.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 14. Contact information For more information, please visit: http://www.ampleon.com For sales office addresses, please visit: http://www.ampleon.com/sales BLM10D3740-35AB Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 — 14 December 2020 © Ampleon Netherlands B.V. 2021. All rights reserved. 12 of 13 BLM10D3740-35AB LDMOS 3-stage integrated Doherty MMIC 15. Contents 1 1.1 1.2 1.3 2 2.1 2.2 3 4 5 6 7 8 8.1 8.2 9 10 11 12 13 13.1 13.2 13.3 13.4 14 15 Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General description . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 3 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 3 Thermal characteristics . . . . . . . . . . . . . . . . . . 3 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Application information. . . . . . . . . . . . . . . . . . . 5 Ruggedness in a Doherty operation . . . . . . . . . 8 Impedance information . . . . . . . . . . . . . . . . . . . 8 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . 9 Handling information. . . . . . . . . . . . . . . . . . . . 10 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 10 Legal information. . . . . . . . . . . . . . . . . . . . . . . 11 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 11 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Contact information. . . . . . . . . . . . . . . . . . . . . 12 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © Ampleon Netherlands B.V. 2021. All rights reserved. For more information, please visit: http://www.ampleon.com For sales office addresses, please visit: http://www.ampleon.com/sales Date of release: 14 December 2020 Document identifier: BLM10D3740-35AB