Data Sheet
ACNU-4804
Positive Logic High CMR Intelligent Power
Module (IPM) and Gate Drive Interface
Optocoupler
Description
Features
The Broadcom® ACNU-4804 is a single-channel fast-speed
optocoupler in SSO8 footprint. It contains a AlGaAs LED
and photo detector with built-in Schmitt trigger to provide
logic compatible waveforms, eliminating the need for
additional wave shaping. The totem pole output eliminates
the need for a pull-up resistor and allows for direct drive
intelligent power modules. Minimized propagation delay
differences between devices makes these optocouplers
excellent solutions for improving inverter efficiency through
reduced switching dead times.
The ACNU-4804 is suitable for IPM interface isolation, AC
and brushless DC motor drives, industrial inverters and
space-constrained industrial applications. This SSO8
package platform features wide 11-mm creepage and
10.5-mm clearance, high insulation voltage of Viorm =
1414 Vpeak and compact footprint which is 40% smaller than
the 400-mil DIP8 package.
Functional Diagram
Applications
1
8
VCC
Anode 2
7
NC
Cathode 3
6
VO
5
GND
NC
NC
4
SHIELD
11-mm creepage, 10.5-mm clearance in compact SSO8
package
Positive output type (totem pole output)
Wide supply voltage: 4.5V to 30V
Maximum propagation delays, tPHL/tPLH at 150 ns/
120 ns
Propagation delay difference (PDD): minimum/
maximum at –130 ns/+130 ns
Maximum pulse width distortion (PWD), 90 ns
Hysteresis
50 kV/µs minimum common-mode rejection at VCM =
1500V
Guaranteed performance within temperature range:
–40°C to +105°C
Worldwide safety approval (pending):
– UL1577 recognized, 5000Vrms/1min
– CSA Approval
– IEC 60747-5-5 Approval for Reinforced Insulation
NOTE: A 0.1-µF bypass capacitor must be connected between
pins VCC and GND. Truth Table guaranteed: Vcc from 4.5V to 30V.
IPM interface isolation
AC and brushless DC motor drives
Industrial inverters
General digital isolation
Truth Table (Non-Inverting Logic)
LED
Output
ON
High
OFF
Low
CAUTION! Take normal static precautions in handling and assembly of this component to prevent damage, degradation,
or both that may be induced by ESD. The components featured in this data sheet are not to be used in military
or aerospace applications or environments.
Broadcom
ACNU-4804-DS100
February 28, 2019
Positive Logic High CMR Intelligent Power Module (IPM) and Gate Drive Interface Optocoupler
ACNU-4804 Data Sheet
Ordering Information
ACNU-4804 is UL Recognized with 5000 Vrms for 1 minute per UL1577.
Option
Part Number
ACNU-4804
RoHS
Compliant
-000E
-500E
Package
Surface Mount
11-mm Stretched
SO8
X
X
Tape and Reel
X
UL 1577
IEC 60747-5-5
Quantity
X
X
80 per tube
X
X
1000 per reel
To order, choose a part number from the part number column and combine with the desired option from the option column
to form an order entry.
Package Outline Drawing
ACNU-4804 SSO8 Package
4804
Solder Reflow Profile
Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-halide flux should be used.
Broadcom
ACNU-4804-DS100
2
Positive Logic High CMR Intelligent Power Module (IPM) and Gate Drive Interface Optocoupler
ACNU-4804 Data Sheet
Regulatory Information
The ACNU-4804 is pending approval by the following organizations.
UL
Approval under UL 1577, component recognition program up to VISO = 5000 VRMS File E55361.
CSA
Approval under CSA Component Acceptance Notice #5, File CA 88324.
IEC 60747-5-5
Maximum Working Insulation Voltage Viorm = 1414Vpeak
Insulation and Safety Related Specifications
Parameter
Symbol
ACNU-4804
Units
Minimum External Air Gap
(External Clearance)
L(101)
10.5
mm
Measured from the input terminals to the output
terminals, shortest distance through air.
Minimum External Tracking
(External Creepage)
L(102)
11.0
mm
Measured from the input terminals to the output
terminals, shortest distance path along body.
0.5
mm
Through insulation distance conductor to conductor,
usually the straight line distance thickness between
the emitter and detector.
>300
V
Minimum Internal Plastic Gap
(Internal Clearance)
Tracking Resistance
(Comparative Tracking Index)
CTI
Isolation Group
IIIa
Conditions
DIN IEC 112/VDE 0303 Part 1
Material Group (DIN VDE 0110, 1/89, Table 1)
IEC 60747-5-5 Insulation Characteristics1
Description
Symbol
Characteristic
Units
Installation classification per DIN VDE 0110/39, Table 1
for rated mains voltage ≤ 600 Vrms
I - IV
for rated mains voltage ≤ 1000 Vrms
I - III
Climatic Classification
40/105/21
Pollution Degree (DIN VDE 0110/39)
2
Maximum Working Insulation Voltage
VIORM
1414
Vpeak
ba
Input to Output Test Voltage, Method
VIORM ×1.875 = VPR, 100% Production Test with tm = 1s, Partial discharge < 5 pC
VPR
2652
Vpeak
Input to Output Test Voltage, Method aa
VIORM × 1.6 = VPR, Type and Sample Test, tm = 10s, Partial discharge < 5 pC
VPR
2262
Vpeak
VIOTM
8000
Vpeak
TS
175
°C
Input Current
IS, INPUT
230
mA
Output Power
PS, OUTPUT
600
mW
RS
>109
Ω
Highest Allowable Overvoltage (Transient Overvoltage tini = 60s)
Safety-limiting values – maximum values allowed in the event of a failure.
Case Temperature
Insulation Resistance at TS, VIO = 500V
a. Refer to the optocoupler section of the Isolation and Control Components Designer's Catalog, under Product Safety Regulations section,
(IEC 60747-5-5) for a detailed description of Method a and Method b partial discharge test profiles.
1.
Broadcom
These optocouplers are suitable for "safe electrical isolation" only within the safety limit data. Maintenance of the safety
limit data shall be ensured by means of protective circuits.
ACNU-4804-DS100
3
Positive Logic High CMR Intelligent Power Module (IPM) and Gate Drive Interface Optocoupler
ACNU-4804 Data Sheet
Absolute Maximum Ratings
Parameter
Symbol
Min.
Max.
Units
Storage Temperature
TS
–55
125
°C
Operating Temperature
TA
–40
105
°C
Average Forward Input Current
IF(avg)
—
20
mA
Peak Transient Input Current
(≤1 µs pulse width, 300 pps)
(
很抱歉,暂时无法提供与“ACNU-4804-000E”相匹配的价格&库存,您可以联系我们找货
免费人工找货