5KT151KGDCM

Disc Ceramic Capacitors General Specifications - SL CAPACITORS - CLASS SL These capacitors have wide temperature characteristics but still offer low loss and linear type TC’s. They are specially designed to be smaller alternative to standard Class I capacitors of linear temperature coefficient. Typical application is RF tuning and decoupling. Ø = 0.6 ± 0.1 (0.024) (0.004) Preferred lead spacing F = 5 (0.197) DIMENSIONS millimeters (inches) millimeters (inches) Digit 9 of P.N. (ø) D±2 (0.079) T max. A 4.0 (0.157) 3.0 (0.118) A,B,D,E,O,R B 5.0 (0.197) 3.0 (0.118) A,B,D,E,O,R,X C 6.0 (0.236) 3.0 (0.118) A,B,C,D,E,O,R,X D 7.0 (0.276) 3.0 (0.118) A,B,C,D,E,O,R,X E 8.0 (0.315) 3.0 (0.118) A,B,C,D,E,O,R,X Lead Spacing Available Lead Spacing F 2.5 (0.100) D — 5 (0.200) A O 6 (0.250) E X 7.5 (0.300) B R 10 (0.400) C W PERFORMANCE CHARACTERISTICS Measured at Dissipation Factor Tolerance Temperature Coefficient Insulation Resistance Dielectric Strength NOTE: Charging current limited to 50 mA Operating Temperature Range (ºC) Climatic Category CR ≤ 100 pF → 1MHz/1.0 Vrms / 25ºC CR > 100 pF → 1kHz/0.3 Vrms / 25ºC CR ≤ 100 pF ... 0.25% 1MHz @ 1.0 Vrms CR > 100 pF ... 1.0% 100kHz @ 0.3 Vrms CR > 100 pF ... 0.25% 1kHz @ 0.3 Vrms CR < 10 pF → ±0.25 pF, ±0.5 pF CR ≥ 10 pF → ±5%, ±10%, ±20% +350 ppm... -1500 ppm (P350... N1500) @ VR → ≥ 10 GΩ VR = 100V → Vt = 250V (DC) VR = 500V → Vt = 1.25kV (DC) -30... +85 30 / 085 / 21 Note: Damp Heat Steady State: 90... 95% R.H. 40ºC / 21 days. No voltage to be applied. 10 Digit 8 of P.N. Disc Ceramic Capacitors Dimension Table - SL SL – CAPACITANCE VS. DISC DIAMETER PHENOLIC COATED millimeters (inches) Temp. Coefficient Digits 1,2,3 of P.N. Rated Voltage (VR) CR (pF) 1.0 1.5 2.2 3.3 4.7 5.6 8.2 10 12 15 18 22 33 47 56 68 82 100 150 180 220 270 330 470 560 680 820 1000 5KK 5KQ 100 VDC 50 VAC 500 VDC 100 VAC 4.0 (0.157) 4.0 (0.157) 5.0 (0.197) 6.0 (0.236) 6.0 (0.236) 7.0 (0.276) 7.0 (0.276) 8.0 (0.315) Diameter (φ) = 9th Part Number Digit 11 Disc Ceramic Capacitors Ordering Code HOW TO ORDER 5 O Q 222 General Purpose 5A = NP0 / I *5B = P100 / I *5C = N150 / I *5D = N220 / I *5E = N330 / I *5F = N470 / I 5G = N750 / I 5H = N1500 / I *5I = N2200 / I *5J = N4700 / I 5K = SL 5M = Y5E / II 5N = Y5F / II 5O = Y5P / II *5P = Y5R / II *5Q = Y5T / II 5S = Y5U / II 5T = Y5V / II 5U = Z5V / II *5V = Z4V / III 5W = Y5P / III 5Y = Y5U / III 5Z = Y5V / III Professional Switch Mode Safety 6A = NP0 / I *6B = P100 / I *6C = N150 / I *6D = N220 / I *6E = N330 / I *6F = N470 / I 6G = N750 / I *6H = N1500 / I *6I = N2200 / I 6J = N4700 / I 61 = SAFETY 62 = SAFETY 65 = SAFETY 67 = Y5U / SM 68 = Y5V / SM 6L = Y5P / SM 6M = X5E / II 6N = X5F / II 6O = X5P / II *6P = X5R / II *6Q = X5T / II 6S = X5U / II 6T = X5V / II 6U = Z5V / II *6V = Z4V / III 6W = Y5P / III 6Y = Y5U / III 6Z = Y5V / III Rated Voltage (dc) D = 16V F = 25V H = 50V K = 100V N = SAFETY O = SAFETY Q = 500V R = 1000V S = 2000V T = 3000V U = 4000V V = SAFETY W = 5000V *X = 6000V *Y = 7500V Capacitance 222 = 2.2 nF *Upon Request 4 Capacitance = TPC code 1 pF = 1R0 1.2pF = 1R2 1.5pF = 1R5 1.8pF = 1R8 2.2pF = 2R2 2.7pF = 2R7 3.9pF = 3R9 4.7pF = 4R7 5.6pF = 5R6 6.8pF = 6R8 8.2pF = 8R2 10pF = 100 12pF = 120 15pF = 150 18pF = 180 22pF = 220 27pF = 270 33pF = 330 39pF = 390 47pF = 470 56pF = 560 68pF = 680 82pF = 820 Capacitance = TPC code 100pF = 101 120pF = 121 150pF = 151 180pF = 181 220pF = 221 270pF = 271 330pF = 331 390pF = 391 470pF = 471 560pF = 561 680pF = 681 820pF = 821 1nF = 102 1.2nF = 122 1.8nF = 182 2.2nF = 222 2.7nF = 272 3.3nF = 332 3.9nF = 392 4.7nF = 472 5.6nF = 562 6.8nF = 682 8.2nF = 822 10nF = 103 15nF = 153 22nF = 223 33nF = 333 47nF = 473 100nF = 104 200nF = 204 Disc Ceramic Capacitors Ordering Code M A E Tolerance C = ±0.25 pF D = ±0.50 pF J = ±5% K = ±10% M = ±20% S = -20+50% Z = -20+80% P = 0+100% A A Packaging Capacitor Diameter ± 2 (0.079) A = 4 (0.157) B = 5 (0.197) C = 6 (0.236) D = 7 (0.276) E = 8 (0.315) F = 9 (0.354) G = 10 (0.394) H = 11 (0.433) J = 13 (0.512) K = 15 (0.591) M* = 19 (0.748) Cardboard Strips A= Bulk E = 5 (0.197) ± 1 (0.039) free wire length C = 10 (0.394) ± 1 (0.039) free wire length D = 25 (0.984) ± 1 (0.039) free wire length Taping Avisert Reel Panasert *Wire 0.8 (0.031) recommended H Lead Forming inches 2.5 ±0.5 +0.6 5 -0.2 +0.6 6 -0.2 +1 7.5 -0.5 +0.5 10 -1.0 +1 12.5 -0.5 .1 ± .025 D – – .2 ± .025 A O N .25 ± .025 E X – .3 ± .05 B R Q .4 ± .05 C W – .5 ± .05 P – – L Avisert Ammo Pack mm L I M M J L L Panasert K M M Finishing Diam ≤9 (0.354) and F = 5.00 (0.197) For every other: Coating does not surpass the bend Low Voltage A = Phenolic General Q = Waxed phenolic ( Purpose ) S = Epoxy (Professional) cap. diameter ≤ 8 (0.315) D = Epoxy (Professional) cap. diameter > 8 (0.315) High Voltage F = Measured from the center of leads 0.6 ± 0.1 (0.024) (0.004) 0.8 ± 0.1 I = Epoxy wire diameter (0.031) (0.004) L = Phenolic wire diameter 0.6 ± 0.1 (0.024) (0.004) C = Epoxy wire diameter Please note that not all code combinations are either possible or available. 5 Disc Ceramic Capacitors Marking DIG. 2 Logo: Only in diam. ≥ 6mm O TC / Class General Purpose A = NP0 / I *B = P100 / I *C = N150 / I *D = N220 / I *E = N330 / I *F = N470 / I G = N750 / I H = N1500 / I *I = N2200 / I *J = N4700 / I K = SL M = Y5E / II N = Y5F / II O = Y5P / II P = Y5R / II Q = Y5T / II S = Y5U / II T = Y5V / II U = Z5V / II V = Z4V / III *W = Y5P / II *X = Y5R / II Y = Y5U / II Z = Y5V / II *Upon Request Professional A = NP0 / I B = P100 / I C = N150 / I D = N220 / I E = N330 / I F = N470 / I G = N750 / I H = N1500 / I I = N2200 / I J = N4700 / I 7 = Y5U / SM 8 = Y5V / SM L = Y5P / SM M = X5E / II N = X5F / II O = X5P / II P = X5R / II Q = X5T / II S = X5U / II T = X5V / II U = Z5V / II V = Z4V / III W = Y5P / III X = Y5R / III Y = Y5U / III Z = Y5V / III 222 OQM DIG. 3 Q DIG. 7 M Rated Voltage D = 16V F = 25V H = 50V K = 100V Q = 500V R = 1000V S = 2000V T = 3000V U = 4000V W = 5000V X = 6000V Y = 7500V Tolerance C = ±0.25pF D = ±0.5pF J = ±5% K = ±10% M = ±20% S = -20 +50% Z = -20 +80% P = 0 +100% Capacitance 1pF = 109 1.2pF = 129 1.5pF = 159 1.8pF = 189 2.2pF = 229 2.7pF = 279 3.9pF = 399 4.7pF = 479 5.6pF = 569 6.8pF = 689 8.2pF = 829 10pF = 100 12pF = 120 15pF = 150 18pF = 180 22pF = 220 27pF = 270 39pF = 390 47pF = 470 56pF = 560 68pF = 680 82pF = 820 Safety Front Capacitance As above EIA 100pF = 101 120pF = 121 150pF = 151 180pF = 181 220pF = 221 270pF = 271 390pF = 391 470pF = 471 560pF = 561 680pF = 681 820pF = 821 1nF = 102 1.2nF = 122 1.8nF = 182 2.2nF = 222 2.7nF = 272 3.9nF = 392 4.7nF = 472 5.6nF = 562 6.8nF = 682 8.2nF = 822 10nF = 103 15nF = 153 22nF = 223 33nF = 333 47nF = 473 100nF = 104 200nF = 204 Type 61V 61V 471M TC – Temperature coefficient. DIG – for better understanding, check pages 3 and 4. 620 65N Tolerance As above Back: (Approval marks) 28 Disc Ceramic Capacitors Packaging IDENTIFICATION AND TRACEABILITY On all TPC ceramic capacitors packages, you will find a bar code label with the following information: Lot number Manufacturing date Quantity of parts per packaging Product part number TAPED PARTS QUANTITY TABLE millimeters (inches) Rated Voltage (Vr) Diameter D Quantities Ammopack Vr