SLIN-12E1A0

NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.69 Vdc - 5.5 Vdc /12 A Outputs November 5, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. RoHS Compliant • • • • SLIN-12E1Ax Features • • • • • • • • • • • • • Rev.E Wide Input Voltage Range Fixed Switching Frequency Power Good Signal Remote Sense Remote On/Off Ability to Sink and Source Current Cost Efficient Open Frame Design Over Temperature Protection Output Over Current Protection Tunable LoopTM (a registered trademark of Lineage Power Systems) to Optimize Dynamic output voltage response Flexible output voltage sequencing Fixed switching frequency and ability to synchronize with external clock Class 1, Category 2, Non-Isolated DC/DC Converter (refer to IPC-9592) Compliant to RoHS EU Directive 2002/95/EC Compatible in a Pb-free or SnPb reflow environment UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-03 Certified VDE‡ 0805:2001-12 (EN60950-1) Licensed Applications • • • Distributed power architectures Intermediate bus voltage applications Telecommunications equipment • • • Servers and storage applications Networking equipment Industrial equipment Description The SLIN-12E1Ax power modules are non-isolated dc-dc converters that can deliver up to 12A of output current. These modules operate over a wide range of input voltage (VIN = 4.5Vdc-14Vdc) and provide a precisely regulated output voltage from 0.69Vdc to 5.5Vdc, programmable via an external resistor. Two new features added with this family of products are the ability to externally tune the voltage control loop and frequency synchronization. Other features include remote On/Off, adjustable output voltage, over current and over temperature protection, power good and output voltage sequencing. The Tunable LoopTM, allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area. Part Selection Output Voltage 0.69 Vdc - 5.5 Vdc Input Voltage 4.5 Vdc - 14 Vdc Max. Output Current 12 A Typical Efficiency 94.3% Model Number Active High SLIN-12E1A0 Model Number Active Low SLIN-12E1AL Notes: Add “G” suffix at the end of the model number to indicate Tray Packaging. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 1 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.69 Vdc - 5.5 Vdc /12 A Outputs Part Number Explanation S LIN – 12 E 1A 0 1 2 34 5 6 November 5, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. 1---Surface mount 2---Series code 3---Output current (12A) 4---Wide input voltage range (4.5-14V) 5---Wide output voltage range (0.69-5.5V) 6---Enable, active high, change “0” to “L” means active low Min -0.3 -0.3 -0.3 -0.3 -40 -55 Typ Max 15 Vin 12 6 85 125 Unit V V v V °C °C Notes Absolute Maximum Ratings Parameter Continuous Input Voltage Voltage on SEQ terminal Voltage on SYNC terminal Voltage on SEQ terminal, SYNC and PG terminals Operating Ambient Temperature Storage Temperature Note: Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Input Specifications Parameter Operating Input Voltage Input Current (full load) Input Current (no load) Input Stand-by Current Input Reflected Ripple Current (pk-pk) I2t Inrush Current Transient Input Ripple Rejection (120Hz) Turn-on Threshold Turn-off Threshold Hysteresis Min 4.5 Typ 26 60 1.2 70 45 4.45 4.2 0.25 Max 14 11.5 1 Unit V A mA mA mA mA A2s dB V V V VIN=4.5V to 14V Vo=0.69V, VIN=10V, IO=0, module enabled Vo=3.3V, VIN=12V, IO=0, module enabled VIN = 12V, module disabled 5Hz to 20MHz, 1μH source impedance; VIN =0 to 14V, IO= IOmax Notes CAUTION: This converter is not internally fused. An input line fuse must be used in application. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 15A. Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 2 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.69 Vdc - 5.5 Vdc /12 A Outputs November 5, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Min -1.5 -2.5 0.69 0 0 0 0 Typ 65 23 2 Max +1.5 +2.5 5.5 0.5 10 5 0.4 10 0.5 80 28 12 150 2 100 1000 5000 Unit %Vo,set %Vo,set V V mV mV %Vo,set mV %Vo,set mV mV A %Io,max A uF uF uF mS Hiccup Mode Vo≤250mV, Hiccup Mode Without the Tunable LoopTM With the Tunable LoopTM With the Tunable LoopTM Case 1: On/Off input is enabled and then input power is applied (delay from instant at which VIN = VIN, min until Vo =10% of Vo, set) Case 2: Input power is applied for at least one second and then the On/Off input is enabled (delay from instant at which Von/Off is enabled until Vo =10% of Vo, set) time for Vo to rise from 10% of Vo, set to 90% of Vo, set Vin=Vin, min to Vin, max, Io=Io, min to Io, max, With or without maximum external capacitance mV uS mV uS di/dt=1A/us, Vin=Vin,nom, Ta=25°C, with a 1µF ceramic capacitor and a 10µF ceramic capacitor. IO=IO, min to IO, max Notes with 0.5% tolerance for external resistor used to set output voltage Over all operating input voltage, resistive load, and temperature conditions until end of life selected by an external resistor Output Specifications Parameter Output Voltage Set Point Output Voltage Adjustment Range1 Remote Sense Range Load Regulation VO ≥ 2.5V VO < 2.5V Line Regulation VO ≥ 2.5V VO < 2.5V Temperature Regulation (-40°C to +85°C) Ripple and Noise (pk-pk) Ripple and Noise (rms) Output Current Range Output DC Current Limit Output Short-Circuit Current Output Capacitance2 ESR≥ 1 mΩ ESR≥0.15 mΩ ESR≥ 10 mΩ VIN=VIN, min to VIN, max VO < 2.5V, Tref=TA, min to TA, max 5Hz to 20MHz BW, VIN=VIN, nom and IO=IO, min to IO, max Co = 0.1μF // 10 μF ceramic capacitors) Turn-On Delay Time 2 mS Output voltage Rise time Output voltage overshoot Dynamic Load Response △V50%~100% - 5 - 3 mS %Vo,set Overshoot Settling Time Overshoot Settling Time - 360 50 400 50 - of Max Load △V100%~50% of Max Load Notes: 1. Some output voltages may not be possible depending on the input voltage. 2. External capacitors may require using the new Tunable LoopTM feature to ensure that the module is stable as well as getting the best transient response (See the Tunable LoopTM section for details). 3. Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 3 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.69 Vdc - 5.5 Vdc /12 A Outputs November 5, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. General Specifications Parameter Efficiency Vo=0.69V Vo=1.2V Vo=1.8V Vo=2.5V Vo=3.3V Vo=5.0V Switching Frequency Over Temperature Protection Sequencing Delay time Tracking Accuracy Power-Up: 0.5V/ms Power-Down: 0.5V/ms PGOOD (Power Good) Output Voltage Limit for PGOOD Pulldown resistance of PGOOD pin Weight MTBF Dimensions Inches (L × W × H) Millimeters (L × W × H) Frequency Synchronization Synchronization Frequency Range High-Level Input Voltage Low-Level Input Voltage Input Current, SYNC Minimum Pulse Width, SYNC Minimum Setup/Hold Time, SYNC 520 2.5 250 250 600 0.8 1 KHz V V mA nS nS 0.80 x 0.45 x 0.334 20.32 x 11.43 x 8.5 84 76.0 83.0 87.6 90.2 92.2 94.3 500 133 10 7 3.68 8,096,640 100 150 116 50 % % % % % % kHz °C mS mV mV %Vo,set Ω g hours Calculated Per Bell Core SR-332 (Io=0.8Io, max, Ta=40°C, Telecordia Method) Delay from VIN, min to application of voltage on SEQ pin Vin, min to Vin, max; Io, min to Io, max, Vseq < Vo Signal Interface Open Drain, Vsupply ≤ 5Vdc Vin= 12Vdc, Ta=25°C Io=Io, max , Vo= Vo,set (for Vo=0.69V, Vin=10Vdc) Min Typ Max Unit Notes Note: Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 4 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.69 Vdc - 5.5 Vdc /12 A Outputs November 5, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Efficiency Data 90 95 85 90 Vin=4.5V EFFICIENCY, η (%) EFFICIENCY, η (%) 85 Vin=4.5V 80 Vin=12V Vin=14V 80 Vin=5V 75 Vin=10V 70 0 2 4 6 8 10 12 75 70 0 2 4 6 8 10 12 OUTPUT CURRENT, IO (A) OUTPUT CURRENT, IO (A) Vo=0.69V 100 95 100 95 Vo=1.2V EFFICIENCY, η (%)) 90 85 80 75 70 0 2 4 6 8 10 12 Vin=4.5V Vin=12V Vin=14V EFFICIENCY, η (%) 90 85 80 75 70 0 2 4 6 8 10 12 Vin=4.5V Vin=12V Vin=14V OUTPUT CURRENT, IO (A) OUTPUT CURRENT, IO (A) Vo=1.8V 100 95 95 100 Vo=2.5V EFFICIENCY, η (%)) 90 Vin=5V 85 80 75 70 0 2 4 6 8 10 12 Vin=12V Vin=14V EFFICIENCY, η (%) Vin=7V 90 Vin=12V Vin=14V 85 80 0 2 4 6 8 10 12 OUTPUT CURRENT, IO (A) OUTPUT CURRENT, IO (A) Vo=3.3V Vo=5.0V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 5 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.69 Vdc - 5.5 Vdc /12 A Outputs November 5, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Thermal Derating Curves 13 12 13 12 OUTPUT CURRENT, Io (A) 11 10 9 8 7 NC 2m/s (400LFM) OUTPUT CURRENT, Io (A) 11 10 9 8 7 6 5 25 35 45 55 65 75 85 NC 2m/s (400LFM) 1m/s (200LFM) 0.5m/s (100LFM) 1m/s (200LFM) 0.5m/s (100LFM) 6 5 25 35 45 55 65 75 85 AMBIENT TEMPERATURE, TA OC AMBIENT TEMPERATURE, TA OC Vo=0.69V 13 12 13 12 Vo=1.2V OUTPUT CURRENT, Io (A) 11 10 9 8 7 6 5 25 35 45 55 65 O OUTPUT CURRENT, Io (A) 11 10 9 8 7 6 5 25 35 45 55 65 O 2m/s (400LFM) 1m/s (200LFM) 0.5m/s (100LFM) NC 2m/s (400LFM) 1m/s (200LFM) 0.5m/s (100LFM) NC 75 85 75 85 AMBIENT TEMPERATURE, TA C AMBIENT TEMPERATURE, TA C Vo=1.8V 13 12 13 12 Vo=2.5V OUTPUT CURRENT, Io (A) OUTPUT CURRENT, Io (A) 11 10 9 8 7 6 NC 2m/s (400LFM) 1m/s (200LFM) 0.5m/s (100LFM) 11 10 9 8 7 6 NC 2m/s (400LFM) 1m/s (200LFM) 0.5m/s (100LFM) 5 25 35 45 55 65 O 5 25 35 45 55 65 O 75 85 75 85 AMBIENT TEMPERATURE, TA C AMBIENT TEMPERATURE, TA C Vo=3.3V Vo=5.0V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 6 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.69 Vdc - 5.5 Vdc /12 A Outputs November 5, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Ripple and Noise Waveforms OUTPUT VOLTAGE VO (V) (20mV/div) TIME, t (1μs/div) OUTPUT VOLTAGE VO (V) (20mV/div) TIME, t (1μs/div) Vo=0.69V, Io = Io,max Vo=1.2V, Io = Io,max OUTPUT VOLTAGE VO (V) (20mV/div) TIME, t (1μs/div) OUTPUT VOLTAGE VO (V) (20mV/div) TIME, t (1μs/div) Vo=1.8V, Io = Io,max Vo=2.5V, Io = Io,max OUTPUT VOLTAGE VO (V) (20mV/div) TIME, t (1μs/div) OUTPUT VOLTAGE VO (V) (20mV/div) TIME, t (1μs/div) Vo=3.3V, Io = Io,max Vo=5.0V, Io = Io,max . Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 7 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.69 Vdc - 5.5 Vdc /12 A Outputs November 5, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Transient Response Waveforms OUTPUT VOLTAGE VO (V) (200mV/div) OUTPUT CURRENT, IO (A) (5Adiv) TIME, t (100μs /div) OUTPUT CURRENT, IO (A) (5Adiv) OUTPUT VOLTAGE VO (V) (200mV/div) TIME, t (100μs /div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vo=0.69V OUTPUT VOLTAGE VO (V) (200mV/div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vo=1.2V OUTPUT VOLTAGE VO (V) (200mV/div) OUTPUT CURRENT, IO (A) (5Adiv) TIME, t (100μs /div) OUTPUT CURRENT, IO (A) (5Adiv) TIME, t (100μs /div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vo=1.8V OUTPUT VOLTAGE VO (V) (200mV/div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vo=2.5V OUTPUT VOLTAGE VO (V) (200mV/div) OUTPUT CURRENT, IO (A) (5Adiv) TIME, t (100μs /div) OUTPUT CURRENT, IO (A) (5Adiv) TIME, t (100μs /div) Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vo=3.3V Transient Response to Dynamic Load Change from 0% to 50% to 0%. Vo=5.0V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 8 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.69 Vdc - 5.5 Vdc /12 A Outputs November 5, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Startup Time ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (200mV/div) VON/OFF (V) (2V/div) TIME, t (1 ms/div) ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (500mV/div) VON/OFF (V) (2V/div) TIME, t (1 ms/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=0.69V Start-up Using On/Off Voltage (Io = Io,max), Vo=1.2V ON/OFF VOLTAGE OUTPUT VOLTAGE VON/OFF (V) (2V/div) VO (V) (500mV/div) TIME, t (1 ms/div) ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VON/OFF (V) (1V/div) TIME, t (1 ms/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=1.8V Start-up Using On/Off Voltage (Io = Io,max), Vo=2.5V TIME, t (1 ms/div) ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (2V/div) VON/OFF (V) (2V/div) ON/OFF VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VON/OFF (V) (2V/div) TIME, t (1 ms/div) Start-up Using On/Off Voltage (Io = Io,max), Vo=3.3V Start-up Using On/Off Voltage (Io = Io,max), Vo=5.0V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 9 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.69 Vdc - 5.5 Vdc /12 A Outputs November 5, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. Startup Time (continued) OUTPUT VOLTAGE VO (V) (200mV/div) TIME, t (1 ms/div) INPUT VOLTAGE OUTPUT VOLTAGE VO (V) (500mV/div) VIN (V) (5V/div) INPUT VOLTAGE VIN (V) (5V/div) TIME, t (1 ms/div) Start-up Using Input Voltage (VIN = 12V, Io = Io,max ), Vo=0.69V OUTPUT VOLTAGE VO (V) (500mV/div) Start-up Using Input Voltage (VIN = 12V, Io = Io,max ), Vo=1.2V TIME, t (1 ms/div) INPUT VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VIN (V) (5V/div) INPUT VOLTAGE VIN (V) (5V/div) TIME, t (1 ms/div) Start-up Using Input Voltage (VIN = 12V, Io = Io,max ), Vo=1.8V Start-up Using Input Voltage (VIN = 12V, Io = Io,max ), Vo=2.5V TIME, t (1 ms/div) INPUT VOLTAGE OUTPUT VOLTAGE VO (V) (2V/div) VIN (V) (5V/div) INPUT VOLTAGE OUTPUT VOLTAGE VO (V) (1V/div) VIN (V) (5V/div) TIME, t (1 ms/div) Start-up Using Input Voltage (VIN = 12V, Io = Io,max ), Vo=3.3V Start-up Using Input Voltage (VIN = 12V, Io = Io,max ), Vo=5.0V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 10 NON-ISOLATED DC/DC CONVERTERS 4.5 Vdc - 14 Vdc Input, 0.69 Vdc - 5.5 Vdc /12 A Outputs November 5, 2009 Bel Power, Inc. , a subsidiary of Bel Fuse, Inc. CURRENT PROBE Test Configurations Input Reflected Ripple Current Test Setup. TO OSCILLOSCOPE LTEST 1μH VIN(+) BATTERY CS 1000μF Electrolytic E.S.R.