Product
Folder
Order
Now
Technical
Documents
Support &
Community
Tools &
Software
Reference
Design
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
ISO772x High-Speed, Robust EMC, Reinforced and Basic Dual-Channel Digital Isolators
1 Features
•
•
1
•
•
•
•
•
•
•
•
•
•
100 Mbps data rate
Robust isolation barrier:
– >100-Year projected lifetime at 1.5 kVRMS
working voltage
– Up to 5000 VRMS Isolation Rating
– Up to 12.8 kV surge capability
– ±100 kV/μs Typical CMTI
Wide supply range: 2.25 V to 5.5 V
2.25-V to 5.5-V level translation
Default output High (ISO772x) and Low
(ISO772xF) Options
Wide temperature range: –55°C to +125°C
Low power consumption, typical 1.7 mA per
channel at 1 Mbps
Low propagation delay: 11 ns typical
Robust electromagnetic compatibility (EMC)
– System-Level ESD, EFT, and surge immunity
– ±8 kV IEC 61000-4-2 contact discharge
protection across isolation barrier
– Low emissions
Wide-SOIC (DW-16, DWV-8) and Narrow-SOIC
(D-8) package options
Automotive Version Available: ISO772x-Q1
Safety-related certifications:
– DIN VDE V 0884-11:2017-01
– UL 1577 component recognition program
– CSA, CQC and TUV certifications
The ISO772x devices provide high electromagnetic
immunity and low emissions at low power
consumption, while isolating CMOS or LVCMOS
digital I/Os. Each isolation channel has a logic input
and output buffer separated by a double capacitive
silicon dioxide (SiO2) insulation barrier. The ISO7720
device has both channels in the same direction while
the ISO7721 device has both channels in the
opposite direction. In the event of input power or
signal loss, the default output is high for devices
without suffix F and low for devices with suffix F. See
the Device Functional Modes section for further
details.
Used in conjunction with isolated power supplies,
these devices help prevent noise currents on data
buses, such as RS-485, RS-232, and CAN, from
damaging sensitive circuitry. Through innovative chip
design and layout techniques, the electromagnetic
compatibility of the ISO772x devices has been
significantly enhanced to ease system-level ESD,
EFT, surge, and emissions compliance. The ISO772x
family of devices is available in 16-pin SOIC widebody (DW), 8-pin SOIC wide-body (DWV), and 8-pin
SOIC narrow-body (D) packages.
Device Information(1)
PART NUMBER
ISO7720, ISO7721
ISO7721F, ISO7721F
ISO7721B, ISO7721FB
PACKAGE
BODY SIZE (NOM)
D (8)
4.90 mm × 3.91 mm
DWV (8)
5.85 mm × 7.50 mm
DW (16)
10.30 mm × 7.50 mm
DW (16)
10.30 mm × 7.50 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Simplified Schematic
2 Applications
•
•
•
•
•
Industrial automation
Motor control
Power supplies
Solar inverters
Medical equipment
Series Isolation
Capacitors
INx
OUTx
GNDI
3 Description
The ISO772x devices are high-performance, dualchannel digital isolators with 5000 VRMS (DW and
DWV packages) and 3000 VRMS (D package) isolation
ratings per UL 1577. This family includes devices with
reinforced insulation ratings according to VDE, CSA,
TUV and CQC. The ISO7721B device is designed for
applications that require basic insulation ratings only.
VCCO
VCCI
GNDO
Copyright © 2016, Texas Instruments Incorporated
VCCI=Input supply, VCCO=Output supply
GNDI=Input ground, GNDO=Output ground
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
6.14
6.15
6.16
6.17
6.18
6.19
1
1
1
2
4
5
Absolute Maximum Ratings ..................................... 5
ESD Ratings.............................................................. 5
Recommended Operating Conditions....................... 5
Thermal Information .................................................. 6
Power Ratings........................................................... 6
Insulation Specifications............................................ 7
Safety-Related Certifications..................................... 8
Safety Limiting Values .............................................. 9
Electrical Characteristics—5-V Supply ................... 10
Supply Current Characteristics—5-V Supply ........ 10
Electrical Characteristics—3.3-V Supply .............. 11
Supply Current Characteristics—3.3-V Supply ..... 11
Electrical Characteristics—2.5-V Supply .............. 12
Supply Current Characteristics—2.5-V Supply ..... 12
Switching Characteristics—5-V Supply................. 13
Switching Characteristics—3.3-V Supply.............. 13
Switching Characteristics—2.5-V Supply.............. 13
Insulation Characteristics Curves ......................... 14
Typical Characteristics .......................................... 15
7
8
Parameter Measurement Information ................ 17
Detailed Description ............................................ 18
8.1
8.2
8.3
8.4
9
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
18
18
19
20
Application and Implementation ........................ 21
9.1 Application Information............................................ 21
9.2 Typical Application .................................................. 22
10 Power Supply Recommendations ..................... 26
11 Layout................................................................... 26
11.1 Layout Guidelines ................................................. 26
11.2 Layout Example .................................................... 26
12 Device and Documentation Support ................. 27
12.1
12.2
12.3
12.4
12.5
12.6
12.7
12.8
Device Support......................................................
Documentation Support ........................................
Related Links ........................................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
27
27
27
27
27
27
28
28
13 Mechanical, Packaging, and Orderable
Information ........................................................... 28
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision D (January 2019) to Revision E
Page
•
Added ISO7721B device to this data sheet for applications that require basic insulation only. Previous data sheet
literature number for ISO7721B was SLLSEY9A ................................................................................................................... 1
•
Changed VDE standard name From: DIN V VDE V 0884-11:2017-01 To: DIN VDE V 0884-11:2017-01 throughout
the document ......................................................................................................................................................................... 1
•
Changed UL certification bullet in Features From: '5000 VRMS (DW-16, DWV-8) and 3000 VRMS (D-8) Isolation
Rating per UL 1577' To: 'UL 1577 component recognition program' .................................................................................... 1
•
Combined CSA, CQC, and TUV Features bullets into a single bullet.................................................................................... 1
•
Updated certification information in Safety-Related Certifications table ................................................................................ 8
Changes from Revision C (July 2018) to Revision D
Page
•
Made editorial and cosmetic changes throughout the document ........................................................................................... 1
•
Changed From: "Isolation Barrier Life: >40 Years" To:">100-Year Projected Lifetime at 1.5 kVRMS Working Voltage"
in Features.............................................................................................................................................................................. 1
•
Added "Up to 5000 VRMS Isolation Rating" in Features ......................................................................................................... 1
•
Added "Up to 12.8 kV Surge Capability" in Features ............................................................................................................ 1
•
Added "±8 kV IEC 61000-4-2 Contact Discharge Protection across Isolation Barrier" in Features....................................... 1
•
Added "Automotive Version Available: ISO772x-Q1" in Features ......................................................................................... 1
•
Deleted "Certification Planned" statement throughout the document ................................................................................... 1
•
Updated Applications list ........................................................................................................................................................ 1
2
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
•
Updated Simplified Schematic to show two isolation capacitors in series per channel instead of a single isolation
capacitor ................................................................................................................................................................................ 1
•
Added "Contact discharge per IEC 61000-4-2" specification of ±8000 V in ESD Ratings table ............................................ 5
•
Changed 'Signaling' rate to 'Data' rate and added table note to Data rate specification in Recommended Operating
Conditions table ..................................................................................................................................................................... 5
•
Changed VIORM Value for DW-16 and DWV-8 packages From: "1414 VPK" To: "2121 VPK" in Insulation Specifications
table ........................................................................................................................................................................................ 7
•
Changed VIOWM Values for DW-16 and DWV-8 packages From: "1000 VRMS" and "1414 VDC" To: "1500 VRMS" and
"2121 VDC" in Insulation Specifications table ......................................................................................................................... 7
•
Added 'see Figure 26" to TEST CONDITIONS of VIOWM specification ................................................................................... 7
•
Changed VIOTM TEST CONDITIONS for 100% production test From: "VTEST = VIOTM" To: "VTEST = 1.2 x VIOTM" in
Insulation Specifications table ............................................................................................................................................... 7
•
Changed VIOSM TEST CONDITIONS From: "Test method per IEC 60065" To: "Test method per IEC 62368-1" in
Insulation Specifications table ............................................................................................................................................... 7
•
Changed qpd TEST CONDITIONS for method b1 test From: "Vini = VIOTM" To: "Vini = 1.2 x VIOTM" in Insulation
Specifications table ................................................................................................................................................................ 7
•
Updated certification information in Safety-Related Certifications table................................................................................. 8
•
Added Insulation Lifetime sub-section under Application Curve section.............................................................................. 24
•
Added 'How to use isolation to improve ESD, EFT and Surge immunity in industrial systems' application report to
Documentation Support section ........................................................................................................................................... 27
Changes from Revision B (March 2017) to Revision C
Page
•
Added the 8-pin SOIC package (DWV) to the data sheet ..................................................................................................... 1
•
Updated the VDE and CSA certification description throughout the document ..................................................................... 1
•
Changed the climatic category for the D package from 5/125/21 to 55/125/21 .................................................................... 7
•
Changed the maximum working voltages for DW-16 and D-8 from 400 to 700 VRMS and 250 to 400 VRMS
(respectively) in the Safety-Related Certifications table......................................................................................................... 8
•
Switched the line colors for VCC at 2.5 V and VCC at 3.3 V in the Low-Level Output Voltage vs Low-Level Output
Current graph........................................................................................................................................................................ 15
•
Deleted EN from the Common-Mode Transient Immunity Test Circuit figure ...................................................................... 17
•
Added the Device Support section ....................................................................................................................................... 27
Changes from Revision A (December 2016) to Revision B
Page
•
Added D-8 values for TUV in the Safety-Related Certifications table ................................................................................... 8
•
Changed the minimum CMTI value from 40 kV/μs to 85 kV/μs in all Electrical Characteristics tables................................ 10
•
Added the Receiving Notification of Documentation Updates section ................................................................................. 27
•
Changed the Electrostatic Discharge Caution statement .................................................................................................... 27
Changes from Original (November 2016) to Revision A
Page
•
Changed Feature From: IEC 60950-1, IEC 60601-1 and IEC 61010-1 End Equipment Standards To: IEC 60950-1
and IEC 60601-1 End Equipment Standards ........................................................................................................................ 1
•
Added Climatic category to the Insulation Specifications....................................................................................................... 7
•
Changed the CSA column of Regulatory Information ........................................................................................................... 8
•
Changed DW package) To: (DW-16) in the TUV column of Regulatory Information ............................................................ 8
•
Changed tie TYP value From: 1.5 To 1 in Switching Characteristics—5-V Supply .............................................................. 13
•
Changed tie TYP value From: 1.5 To 1 in Switching Characteristics—3.3-V Supply ........................................................... 13
•
Changed tie TYP value From: 1.5 To 1 in Switching Characteristics—2.5-V Supply ........................................................... 13
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
3
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
5 Pin Configuration and Functions
ISO7720 DW Package
16-Pin SOIC
Top View
16 GND2
2
15
VCC1
3
INA
4
INB
5
NC
ISOLATION
NC
GND1 1
NC
16 GND2
NC
2
15
14 VCC2
VCC1
3
14 VCC2
13 OUTA
OUTA 4
ISOLATION
GND1 1
ISO7721 DW Package
16-Pin SOIC
Top View
13
NC
INA
12 OUTB
INB
5
6
11
NC
NC
6
11
NC
GND1 7
10
NC
GND1 7
10
NC
8
9 GND2
NC
8
9 GND2
VCC1
1
INA
2
INB
3
ISOLATION
ISO7720 D and DWV Package
8-Pin SOIC
Top View
ISO7721 D and DWV Package
8-Pin SOIC
Top View
8 VCC2
VCC1
7 OUTA
OUTA 2
6 OUTB
GND1 4
INB
5 GND2
1
8 VCC2
ISOLATION
NC
12 OUTB
3
GND1 4
7
INA
6 OUTB
5 GND2
Pin Functions
PIN
NAME
DW PACKAGE
D, DWV PACKAGE
I/O
DESCRIPTION
ISO7720
ISO7721
ISO7720
ISO7721
1, 7
1, 7
4
4
—
Ground connection for VCC1
9
9
16
16
5
5
—
Ground connection for VCC2
INA
4
13
2
7
I
Input, channel A
INB
5
5
3
3
I
Input, channel B
NC
2, 6, 8, 10, 11,
15
2, 6, 8, 10,
11, 15
—
—
—
Not connected
GND1
GND2
OUTA
13
4
7
2
O
Output, channel A
OUTB
12
12
6
6
O
Output, channel B
VCC1
3
3
1
1
—
Power supply, VCC1
VCC2
14
14
8
8
—
Power supply, VCC2
4
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
6 Specifications
6.1 Absolute Maximum Ratings
See
(1)
.
Supply voltage (2)
VCC1, VCC2
MIN
MAX
–0.5
6
V
Voltage at INx, OUTx
–0.5
IO
Output current
–15
TJ
Junction temperature
Tstg
Storage temperature
(1)
(2)
(3)
VCC + 0.5
–65
UNIT
V
(3)
V
15
mA
150
°C
150
°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values except differential I/O bus voltages are with respect to the local ground terminal (GND1 or GND2) and are peak
voltage values.
Maximum voltage must not exceed 6 V.
6.2 ESD Ratings
VALUE
(1)
±6000
Charged device model (CDM), per JEDEC specification JESD22-C101,
all pins (2)
±1500
Contact discharge per IEC 61000-4-2; Isolation barrier withstand
test (3) (4)
±8000
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins
VESD
(1)
(2)
(3)
(4)
Electrostatic discharge
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
IEC ESD strike is applied across the barrier with all pins on each side tied together creating a two-terminal device.
Testing is carried out in air or oil to determine the intrinsic contact discharge capability of the device.
6.3 Recommended Operating Conditions
MIN
NOM
MAX
5.5
V
2
2.25
V
VCC1, VCC2
Supply voltage
VCC(UVLO+)
UVLO threshold when supply voltage is rising
VCC(UVLO-)
UVLO threshold when supply voltage is falling
1.7
1.8
V
VHYS(UVLO)
Supply voltage UVLO hysteresis
100
200
mV
IOH
High-level output current
IOL
Low-level output current
2.25
UNIT
VCCO (1) = 5 V
–4
VCCO = 3.3 V
–2
VCCO = 2.5 V
–1
mA
VCCO = 5 V
4
VCCO = 3.3 V
2
VCCO = 2.5 V
1
mA
VIH
High-level input voltage
0.7 × VCCI (1)
VCCI
VIL
Low-level input voltage
0
0.3 × VCCI
DR (2)
Data rate
0
100
Mbps
TA
Ambient temperature
125
°C
(1)
(2)
–55
25
V
V
VCCI = Input-side VCC; VCCO = Output-side VCC.
100 Mbps is the maximum specified data rate, although higher data rates are possible.
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
5
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
6.4 Thermal Information
ISO772x
THERMAL METRIC (1)
DW (SOIC)
DWV (SOIC)
D (SOIC)
16 PINS
16 PINS
8 PINS
UNIT
RθJA
Junction-to-ambient thermal resistance
86.5
84.3
137.7
°C/W
RθJC(top)
Junction-to-case(top) thermal resistance
49.6
36.3
54.9
°C/W
RθJB
Junction-to-board thermal resistance
49.7
47.0
71.7
°C/W
ψJT
Junction-to-top characterization parameter
32.3
7.4
7.1
°C/W
ψJB
Junction-to-board characterization parameter
49.2
45.1
70.7
°C/W
RθJC(botto
Junction-to-case(bottom) thermal resistance
N/A
N/A
N/A
°C/W
m)
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Power Ratings
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ISO7720
PD
Maximum power dissipation
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50 MHz 50% duty cycle square wave
100
mW
PD1
Maximum power dissipation by side-1
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50 MHz 50% duty cycle square wave
20
mW
PD2
Maximum power dissipation by side-2
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50 MHz 50% duty cycle square wave
80
mW
PD
Maximum power dissipation
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50 MHz 50% duty cycle square wave
100
mW
PD1
Maximum power dissipation by side-1
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50 MHz 50% duty cycle square wave
50
mW
PD2
Maximum power dissipation by side-2
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
input a 50 MHz 50% duty cycle square wave
50
mW
ISO7721
6
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
6.6 Insulation Specifications
PARAMETER
CLR
External clearance
VALUE
TEST CONDITIONS
8
8.5
4
mm
(1)
8
8.5
4
mm
21
21
21
μm
>600
>600
>600
V
Distance through the
insulation
Minimum internal gap (internal clearance)
CTI
Comparative tracking
index
DIN EN 60112 (VDE 0303-11); IEC 60112; UL 746A
Material group
According to IEC 60664-1
Overvoltage category per
IEC 60664-1
DIN V VDE V 0884-11:2017-01
I
I
I
Rated mains voltage ≤ 150 VRMS
I–IV
I–IV
I–IV
Rated mains voltage ≤ 300 VRMS
I–IV
I–IV
I–III
Rated mains voltage ≤ 600 VRMS
I–IV
I–IV
n/a
Rated mains voltage ≤ 1000 VRMS
I–III
I–III
n/a
ISO772x
2121
2121
637
ISO7721B
1414
n/a
n/a
ISO772x
1500
1500
450
ISO7721B
1000
n/a
n/a
ISO772x
2121
2121
637
ISO7721B
1414
n/a
n/a
8000
7071
4242
VTEST = 1.6 × VIOSM
(ISO772x)
8000
8000
5000
VTEST = 1.3 × VIOSM
(ISO7721B)
6000
n/a
n/a
≤5
≤5
≤5
Vpd(m) = 1.6 × VIORM,
tm = 10 s (ISO772x)
≤5
≤5
≤5
Vpd(m) = 1.2 × VIORM,
tm = 10 s (ISO7721B)
≤5
n/a
n/a
Vpd(m) = 1.875 ×
VIORM,
tm = 1 s (ISO772x)
≤5
≤5
≤5
Vpd(m) = 1.5 × VIORM,
tm = 1 s (ISO7721B)
≤5
n/a
n/a
~0.5
~0.5
~0.5
(2)
VIORM
Maximum repetitive peak
isolation voltage
VIOWM
Maximum working
isolation voltage
AC voltage (bipolar)
AC voltage; Time dependent dielectric
breakdown (TDDB) test; see Figure 26
DC voltage
VIOTM
Maximum transient
isolation voltage
VTEST = VIOTM, t = 60 s (qualification);
VTEST = 1.2 x VIOTM, t = 1 s (100% production)
VIOSM
Maximum surge isolation
voltage (3)
Test method per IEC 62368-1, 1.2/50 µs
waveform,
Method a, After Input/Output safety test subgroup 2/3,
Vini = VIOTM, tini = 60 s;
Vpd(m) = 1.2 × VIORM, tm = 10 s
Apparent charge (4)
Method a, After environmental tests
subgroup 1,
Vini = VIOTM, tini = 60 s;
Method b1; At routine test (100%
production) and preconditioning (type
test),
Vini = 1.2 x VIOTM, tini = 1 s;
Barrier capacitance, input
to output (5)
Isolation resistance (5)
VIO = 0.4 × sin (2πft), f = 1 MHz
(2)
(3)
(4)
(5)
VPK
VRMS
VDC
VPK
VPK
12
12
pC
pF
12
VIO = 500 V, TA = 25°C
>10
>10
VIO = 500 V, 100°C ≤ TA ≤ 125°C
>1011
>1011
>1011
9
9
9
VIO = 500 V at TS = 150°C
(1)
UNIT
Shortest terminal-to-terminal distance across the package
surface
DTI
RIO
D
Shortest terminal-to-terminal distance through air
External creepage
CIO
DWV
(1)
CPG
qpd
DW
>10
>10
>10
Pollution degree
2
2
2
Climatic category
55/125/
21
55/125/
21
55/125/
21
Ω
>10
Creepage and clearance requirements should be applied according to the specific equipment isolation standards of an application. Care
should be taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the isolator on
the printed-circuit board do not reduce this distance. Creepage and clearance on a printed-circuit board become equal in certain cases.
Techniques such as inserting grooves and/or ribs on a printed circuit board are used to help increase these specifications.
This coupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured by
means of suitable protective circuits.
Testing is carried out in air or oil to determine the intrinsic surge immunity of the isolation barrier.
Apparent charge is electrical discharge caused by a partial discharge (pd).
All pins on each side of the barrier tied together creating a two-terminal device.
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
7
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
Insulation Specifications (continued)
PARAMETER
VALUE
TEST CONDITIONS
DW
DWV
D
5000
5000
3000
UNIT
UL 1577
VISO
Withstanding isolation
voltage
VTEST = VISO, t = 60 s(qualification);
VTEST = 1.2 × VISO, t = 1 s (100% production)
VRMS
6.7 Safety-Related Certifications
VDE
Certified according to DIN
VDE V 0884-11:2017-01
CSA
UL
Certified according to IEC
60950-1, IEC 62368-1 and
IEC 60601-1
Recognized under UL
Certified according to
1577 Component
GB4943.1-2011
Recognition Program
800 VRMS (DW-16) and 850
VRMS (DWV-8) reinforced
Maximum transient isolation insulation and 400 VRMS
voltage, 8000 VPK (DW-16), (D-8) basic insulation
working voltage per CSA
7071 VPK (DWV-8) and
60950-1-07+A1+A2, IEC
4242 VPK (D-8);
60950-1 2nd Ed.+A1+A2,
Maximum repetitive peak
isolation voltage, 2121 VPK CSA 62368-1-14 and IEC
DW-16, DWV-8:
62368-1:2014, (pollution
(DW-16, DWV-8,
Single protection,
degree 2, material group I); 5000 VRMS;
Reinforced), 1414 VPK
(DW-16, Basic) and 637
D-8: Single
VPK (D-8);
protection, 3000 VRMS
2 MOPP (Means of Patient
Maximum surge isolation
voltage, 8000 VPK (DW-16, Protection) per CSA 60601DWV-8, Reinforced), 6000 1:14 and IEC 60601-1 Ed.
3.1, 250 VRMS (DW-16,
VPK (DW-16, Basic) and
DWV-8) max working
5000 VPK (D-8)
voltage
Certificate numbers:
40040142 (Reinforced)
40047657 (Basic)
8
Master contract number:
220991
CQC
TUV
Certified according to EN
61010-1:2010/A1:2019,
EN 609501:2006/A2:2013 and EN
62368-1:2014
5000 VRMS (DW-16,
DWV-8) and 3000 VRMS
(D-8) Reinforced
insulation per EN 610101:2010/A1:2019 up to
DW-16, DWV-8: Reinforced
working voltage of 600
Insulation, Altitude ≤ 5000 m, V
RMS (DW-16, DWV-8)
Tropical Climate,700 VRMS
and 300 VRMS (D-8)
maximum working voltage;
D-8: Basic Insulation,
5000 VRMS (DW-16,
Altitude ≤ 5000 m, Tropical
Climate, 400 VRMS maximum DWV-8) and 3000 VRMS
(D-8) Reinforced
working voltage
insulation per EN 609501:2006/A2:2013 and EN
62368-1:2014 up to
working voltage of 800
VRMS (DW-16, DWV-8)
and 400 VRMS (D-8)
Certificate numbers:
CQC15001121716 (DW-16)
File number: E181974
CQC18001199096 (DWV-8)
CQC15001121656 (D-8)
Submit Documentation Feedback
Client ID number: 77311
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
6.8 Safety Limiting Values
Safety limiting intends to minimize potential damage to the isolation barrier upon failure of input or output circuitry.
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
DW-16 PACKAGE
IS
Safety input, output, or supply
current (1)
PS
Safety input, output, or total
power (1)
TS
Maximum safety
temperature (1)
RθJA = 86.5 °C/W, VI = 5.5 V, TJ = 150°C, TA = 25°C, see Figure 1
263
RθJA = 86.5 °C/W, VI = 3.6 V, TJ = 150°C, TA = 25°C, see Figure 1
401
RθJA = 86.5 °C/W, VI = 2.75 V, TJ = 150°C, TA = 25°C, see Figure 1
525
RθJA = 86.5 °C/W, TJ = 150°C, TA = 25°C, see Figure 2
mA
1445
mW
150
°C
DWV-8 PACKAGE
IS
Safety input, output, or supply
current (1)
PS
Safety input, output, or total
power (1)
TS
Maximum safety
temperature (1)
RθJA = 84.3 °C/W, VI = 5.5 V, TJ = 150°C, TA = 25°C, see Figure 3
270
RθJA = 84.3 °C/W, VI = 3.6 V, TJ = 150°C, TA = 25°C, see Figure 3
412
RθJA = 84.3 °C/W, VI = 2.75 V, TJ = 150°C, TA = 25°C, see Figure 3
539
RθJA = 84.3 °C/W, TJ = 150°C, TA = 25°C, see Figure 4
mA
1483
mW
150
°C
D-8 PACKAGE
IS
Safety input, output, or supply
current (1)
PS
Safety input, output, or total
power (1)
TS
Maximum safety
temperature (1)
(1)
RθJA = 137.7 °C/W, VI = 5.5 V, TJ = 150°C, TA = 25°C, see Figure 5
165
RθJA = 137.7 °C/W, VI = 3.6 V, TJ = 150°C, TA = 25°C, see Figure 5
252
RθJA = 137.7 °C/W, VI = 2.75 V, TJ = 150°C, TA = 25°C, see Figure 5
330
RθJA = 137.7 °C/W, TJ = 150°C, TA = 25°C, see Figure 6
908
mW
150
°C
mA
The maximum safety temperature, TS, has the same value as the maximum junction temperature, TJ, specified for the device. The IS
and PS parameters represent the safety current and safety power respectively. The maximum limits of IS and PS should not be
exceeded. These limits vary with the ambient temperature, TA.
The junction-to-air thermal resistance, RθJA, in the Thermal Information table is that of a device installed on a high-K test board for
leaded surface-mount packages. Use these equations to calculate the value for each parameter:
TJ = TA + RθJA × P, where P is the power dissipated in the device.
TJ(max) = TS = TA + RθJA × PS, where TJ(max) is the maximum allowed junction temperature.
PS = IS × VI, where VI is the maximum input voltage.
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
9
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
6.9 Electrical Characteristics—5-V Supply
VCC1 = VCC2 = 5 V ± 10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
VCCO (1) –
0.4
4.8
VOH
High-level output voltage
IOH = –4 mA; see Figure 15
VOL
Low-level output voltage
IOL = 4 mA; see Figure 15
VIT+(IN)
Rising input threshold voltage
VIT-(IN)
Falling input threshold voltage
0.3 x VCCI
0.4 x VCCI
VI(HYS)
Input threshold voltage hysteresis
0.1 × VCCI
0.2 × VCCI
IIH
High-level input current
VIH = VCCI (1) at INx
IIL
Low-level input current
VIL = 0 V at INx
CMTI
Common-mode transient
immunity
VI = VCCI or 0 V, VCM = 1200 V; see Figure 17
CI
Input Capacitance (2)
VI = VCC/ 2 + 0.4×sin(2πft), f = 1 MHz, VCC = 5 V
(1)
(2)
MAX
V
0.2
0.4
V
0.6 x VCCI
0.7 x VCCI
V
V
V
10
–10
85
UNIT
μA
µA
100
kV/μs
2
pF
VCCI = Input-side VCC; VCCO = Output-side VCC.
Measured from input pin to ground.
6.10 Supply Current Characteristics—5-V Supply
VCC1 = VCC2 = 5 V ± 10% (over recommended operating conditions unless otherwise noted)
PARAMETER
SUPPLY
CURRENT
TEST CONDITIONS
MIN
TYP
MAX
ICC1
0.8
1.1
ICC2
1.1
1.7
ICC1
2.9
4.2
ICC2
1.2
1.9
ICC1
1.8
2.7
ICC2
1.3
1.9
ICC1
1.9
2.7
ICC2
2.2
3
ICC1
2.5
3.2
ICC2
11.6
14
UNIT
ISO7720
VI = VCCI (ISO7720), VI = 0 V (ISO7720 with F suffix)
Supply current - DC signal
VI = 0 V (ISO7720), VI = VCCI (ISO7720 with F suffix)
1 Mbps
Supply current - AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
mA
ISO7721
Supply current - DC signal
Supply current - AC signal
10
VI = VCCI (ISO7721),
VI = 0 V (ISO7721 with F suffix)
ICC1, ICC2
1
1.6
VI = 0 V (ISO7721),
VI = VCCI (ISO7721 with F suffix)
ICC1, ICC2
2.2
3.2
1 Mbps
ICC1, ICC2
1.7
2.4
10 Mbps
ICC1, ICC2
2.2
3
100 Mbps
ICC1, ICC2
7.3
9
All channels switching with square
wave clock input; CL = 15 pF
mA
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
6.11 Electrical Characteristics—3.3-V Supply
VCC1 = VCC2 = 3.3 V ± 10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
VCCO (1) – 0.3
3.2
VOH
High-level output voltage
IOH = –2 mA; see Figure 15
VOL
Low-level output voltage
IOL = 2 mA; see Figure 15
VIT+(IN)
Rising input voltage threshold
VIT-(IN)
Falling input voltage threshold
0.3 x VCCI
0.4 x VCCI
VI(HYS)
Input threshold voltage hysteresis
0.1 × VCCI
0.2 × VCCI
IIH
High-level input current
VIH = VCCI (1) at INx
IIL
Low-level input current
VIL = 0 V at INx
CMTI
Common-mode transient immunity
VI = VCCI or 0 V, VCM = 1200 V; see Figure 17
(1)
MAX
UNIT
V
0.1
0.3
V
0.6 x VCCI
0.7 x VCCI
V
V
V
10
–10
μA
µA
85
100
kV/μs
MIN
TYP
MAX
ICC1
0.8
1.1
ICC2
1.1
1.7
ICC1
2.9
4.2
ICC2
1.2
1.9
ICC1
1.8
2.7
ICC2
1.2
1.9
ICC1
1.9
2.7
ICC2
1.9
2.6
ICC1
2.2
3.1
ICC2
8.6
11
VCCI = Input-side VCC; VCCO = Output-side VCC.
6.12 Supply Current Characteristics—3.3-V Supply
VCC1 = VCC2 = 3.3 V ± 10% (over recommended operating conditions unless otherwise noted)
PARAMETER
SUPPLY
CURRENT
TEST CONDITIONS
UNIT
ISO7720
VI = VCCI (ISO7720), VI = 0 V (ISO7720 with F suffix)
Supply current - DC signal
VI = 0 V (ISO7720), VI = VCCI (ISO7720 with F suffix)
1 Mbps
Supply current - AC signal
All channels switching with square wave
clock input; CL = 15 pF
10 Mbps
100 Mbps
mA
ISO7721
Supply current - DC signal
Supply current - AC signal
VI = VCCI (ISO7721), VI = 0 V (ISO7721 with F suffix)
ICC1, ICC2
1
1.6
VI = 0 V (ISO7721), VI = VCCI (ISO7721 with F suffix)
ICC1, ICC2
2.2
3.2
1 Mbps
ICC1, ICC2
1.6
2.4
10 Mbps
ICC1, ICC2
2
2.8
100 Mbps
ICC1, ICC2
5.6
7
All channels switching with square wave
clock input; CL = 15 pF
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
mA
11
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
6.13 Electrical Characteristics—2.5-V Supply
VCC1 = VCC2 = 2.5 V ± 10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
VCCO (1) – 0.2
2.45
VOH
High-level output voltage
IOH = –1 mA; see Figure 15
VOL
Low-level output voltage
IOL = 1 mA; see Figure 15
VIT+(IN)
Rising input voltage threshold
VIT-(IN)
Falling input voltage threshold
0.3 x VCCI
0.4 x VCCI
VI(HYS)
Input threshold voltage hysteresis
0.1 × VCCI
0.2 × VCCI
IIH
High-level input current
VIH = VCCI (1) at INx
IIL
Low-level input current
VIL = 0 V at INx
CMTI
Common-mode transient immunity
VI = VCCI or 0 V, VCM = 1200 V; see Figure 17
(1)
MAX
V
0.05
0.2
V
0.6 x VCCI
0.7 x VCCI
V
V
V
10
–10
85
UNIT
μA
μA
100
kV/μs
VCCI = Input-side VCC; VCCO = Output-side VCC.
6.14 Supply Current Characteristics—2.5-V Supply
VCC1 = VCC2 = 2.5 V ± 10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
SUPPLY CURRENT
MIN
TYP
MAX
ICC1
0.8
1.1
ICC2
1.1
1.7
ICC1
2.9
4.2
ICC2
1.2
1.9
ICC1
1.8
2.7
ICC2
1.3
1.9
ICC1
1.9
2.7
ICC2
1.7
2.4
ICC1
2.2
3
ICC2
6.8
9
UNIT
ISO7720
VI = VCCI (ISO7720), VI = 0 V (ISO7720 with F suffix)
Supply current - DC signal
VI = 0 V (ISO7720), VI = VCCI (ISO7720 with F suffix)
1 Mbps
Supply current - AC signal
All channels switching with square
wave clock input; CL = 15 pF
10 Mbps
100 Mbps
mA
ISO7721
Supply current - DC signal
Supply current - AC signal
12
VI = VCCI (ISO7721), VI = 0 V (ISO7721 with F suffix)
ICC1, ICC2
1
1.6
VI = 0 V (ISO7721), VI = VCCI (ISO7721 with F suffix)
ICC1, ICC2
2.2
3.2
1 Mbps
ICC1, ICC2
1.6
2.4
10 Mbps
ICC1, ICC2
1.9
2.7
100 Mbps
ICC1, ICC2
4.6
6
All channels switching with square
wave clock input; CL = 15 pF
Submit Documentation Feedback
mA
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
6.15 Switching Characteristics—5-V Supply
VCC1 = VCC2 = 5 V ± 10% (over recommended operating conditions unless otherwise noted)
PARAMETER
tPLH, tPHL
Propagation delay time
PWD
Pulse width distortion (1) |tPHL – tPLH|
tsk(o)
Channel-to-channel output skew time (2)
tsk(pp)
Part-to-part skew time (3)
tr
Output signal rise time
tf
Output signal fall time
TEST CONDITIONS
MAX
11
16
ns
0.5
4.9
ns
4
ns
4.5
ns
1.8
3.9
ns
1.9
3.9
ns
0.1
0.3
μs
Same direction channels
See Figure 15
tDO
Default output delay time from input power loss
tie
Time interval error
216 – 1 PRBS data at 100 Mbps
(3)
TYP
6
See Figure 15
Measured from the time VCC goes below 1.7
V. See Figure 16
(1)
(2)
MIN
1
UNIT
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
6.16 Switching Characteristics—3.3-V Supply
VCC1 = VCC2 = 3.3 V ± 10% (over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
tPLH, tPHL
Propagation delay time
PWD
Pulse width distortion (1) |tPHL – tPLH|
tsk(o)
Channel-to-channel output skew time (2)
tsk(pp)
Part-to-part skew time (3)
tr
Output signal rise time
tf
Output signal fall time
See Figure 15
MAX
11
16
ns
0.5
5
ns
4.1
ns
4.5
ns
0.7
3
ns
0.7
3
ns
0.1
0.3
μs
See Figure 15
tDO
Default output delay time from input power loss
tie
Time interval error
216 – 1 PRBS data at 100 Mbps
(3)
TYP
6
Same direction channels
Measured from the time VCC goes
below 1.7 V. See Figure 16
(1)
(2)
MIN
1
UNIT
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
6.17 Switching Characteristics—2.5-V Supply
VCC1 = VCC2 = 2.5 V ± 10% (over recommended operating conditions unless otherwise noted)
PARAMETER
tPLH, tPHL
Propagation delay time
PWD
Pulse width distortion (1) |tPHL – tPLH|
tsk(o)
Channel-to-channel output skew time
tsk(pp)
Part-to-part skew time (3)
tr
Output signal rise time
tf
Output signal fall time
tDO
tie
(1)
(2)
(3)
TEST CONDITIONS
See Figure 15
(2)
TYP
MAX
UNIT
7.5
12
18.5
ns
0.5
5.1
ns
4.1
ns
4.6
ns
1
3.5
ns
1
3.5
ns
0.1
0.3
μs
Same direction channels
See Figure 15
Default output delay time from input power loss
Time interval error
MIN
Measured from the time VCC goes
below 1.7 V. See Figure 16
16
2
– 1 PRBS data at 100 Mbps
1
ns
Also known as pulse skew.
tsk(o) is the skew between outputs of a single device with all driving inputs connected together and the outputs switching in the same
direction while driving identical loads.
tsk(pp) is the magnitude of the difference in propagation delay times between any terminals of different devices switching in the same
direction while operating at identical supply voltages, temperature, input signals and loads.
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
13
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
6.18 Insulation Characteristics Curves
1600
VCC1 = VCC2 = 2.75 V
VCC1 = VCC2 = 3.6 V
VCC1 = VCC2 = 5.5 V
500
1400
Safety Limiting Current (mA)
Safety Limiting Current (mA)
600
400
300
200
100
50
100
150
Ambient Temperature (qC)
600
400
0
200
50
D001
Figure 1. Thermal Derating Curve for Limiting Current per
VDE for DW-16 Package
100
150
Ambient Temperature (qC)
200
D002
Figure 2. Thermal Derating Curve for Limiting Power per
VDE for DW-16 Package
600
1600
VCC1 = VCC2 = 2.75 V
VCC1 = VCC2 = 3.6 V
VCC1 = VCC2 = 5.5 V
500
1400
Safety Limiting Current (mA)
Safety Limiting Current (mA)
800
0
0
400
300
200
100
1200
1000
800
600
400
200
0
0
0
50
100
150
Ambient Temperature (qC)
200
0
50
D013
Figure 3. Thermal Derating Curve for Limiting Current per
VDE for DWV-8 Package
100
150
Ambient Temperature (qC)
200
D014
Figure 4. Thermal Derating Curve for Limiting Power per
VDE for DWV-8 Package
350
1000
VCC1 = VCC2 = 2.75 V
VCC1 = VCC2 = 3.6 V
VCC1 = VCC2 = 5.5 V
900
Safety Limiting Current (mA)
300
Safety Limiting Current (mA)
1000
200
0
250
200
150
100
50
800
700
600
500
400
300
200
100
0
0
0
50
100
150
Ambient Temperature (qC)
200
0
D003
Figure 5. Thermal Derating Curve for Limiting Current per
VDE for D-8 Package
14
1200
50
100
150
Ambient Temperature (qC)
200
D004
Figure 6. Thermal Derating Curve for Limiting Power per
VDE for D-8 Package
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
6.19 Typical Characteristics
5
14
ICC1 at 2.5 V
ICC2 at 2.5 V
ICC1 at 3.3 V
ICC1 at 2.5 V
ICC2 at 2.5 V
ICC1 at 3.3 V
4.5
4
10
Supply Current (mA)
Supply Current (mA)
12
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
8
6
4
ICC2 at 3.3 V
ICC1 at 5 V
ICC2 at 5 V
3.5
3
2.5
2
1.5
1
2
0.5
0
0
0
25
50
Data Rate (Mbps)
TA = 25°C
75
0
100
CL = 15 pF
50
Data Rate (Mbps)
TA = 25°C
Figure 7. ISO7720 Supply Current vs Data Rate
(With 15-pF Load)
75
100
D006
CL = No Load
Figure 8. ISO7720 Supply Current vs Data Rate
(With No Load)
4
9
ICC1, ICC2 at 2.5 V
ICC1, ICC2 at 3.3 V
ICC1, ICC2 at 5 V
8
ICC1, ICC2 at 2.5 V
ICC1, ICC2 at 3.3 V
ICC1, ICC2 at 5 V
3.5
Supply Current (mA)
7
Supply Current (mA)
25
D005
6
5
4
3
2
3
2.5
2
1.5
1
0.5
1
0
0
0
25
TA = 25°C
50
Data Rate (Mbps)
75
0
100
25
D007
CL = 15 pF
TA = 25°C
Figure 9. ISO7721 Supply Current vs Data Rate
(With 15-pF Load)
50
Data Rate (Mbps)
75
100
D008
CL = No Load
Figure 10. ISO7721 Supply Current vs Data Rate
(With No Load)
6
0.9
Low-Level Output Voltage (V)
High-Level Output Voltage (V)
0.8
5
4
3
2
VCC at 2.5 V
VCC at 3.3 V
VCC at 5 V
1
0
-15
0.7
0.6
0.5
0.4
0.3
0.2
VCC at 2.5 V
VCC at 3.3 V
VCC at 5 V
0.1
0
-10
-5
High-Level Output Current (mA)
0
0
5
10
Low-Level Output Current (mA)
D011
TA = 25°C
15
D012
TA = 25°C
Figure 11. High-Level Output Voltage vs High-level
Output Current
Figure 12. Low-Level Output Voltage vs Low-Level
Output Current
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
15
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
Typical Characteristics (continued)
14
Propagation Delay Time (ns)
Power Supply UVLO Threshold (V)
2.1
2.05
2
1.95
1.9
1.85
1.8
1.75
1.7
VCC1+
VCC1-
1.65
1.6
-55
-25
5
35
65
Free-Air Temperature (qC)
VCC2+
VCC295
125
12
11
10
tPLH at 2.5 V
tPHL at 2.5 V
tPLH at 3.3 V
9
8
-55
-25
D011
Figure 13. Power Supply Undervoltage Threshold vs
Free-Air Temperature
16
13
5
35
65
Free Air Temperature (qC)
tPHL at 3.3 V
tPLH at 5 V
tPHL at 5 V
95
125
D012
Figure 14. Propagation Delay Time vs Free-Air Temperature
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
7 Parameter Measurement Information
Isolation Barrier
IN
Input Generator
(See Note A)
VI
VCCI
VI
OUT
50%
50%
0V
tPLH
CL
See Note B
VO
50
tPHL
VOH
90%
50%
VO
50%
10%
VOL
tf
tr
A.
The input pulse is supplied by a generator having the following characteristics: PRR ≤ 50 kHz, 50% duty cycle, tr ≤ 3
ns, tf ≤ 3 ns, ZO = 50 Ω. At the input, 50 Ω resistor is required to terminate Input Generator signal. It is not needed in
actual application.
B.
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 15. Switching Characteristics Test Circuit and Voltage Waveforms
VI
See Note B
VCC
VCC
Isolation Barrier
IN = 0 V (Devices without suffix F)
IN = VCC (Devices with suffix F)
VI
IN
1.7 V
0V
OUT
VO
tDO
CL
See Note A
default high
VOH
50%
VO
VOL
default low
A.
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
B.
Power Supply Ramp Rate = 10 mV/ns
Figure 16. Default Output Delay Time Test Circuit and Voltage Waveforms
VCCI
VCCO
C = 0.1 µF ±1%
Pass-fail criteria:
The output must
remain stable.
Isolation Barrier
S1
C = 0.1 µF ±1%
IN
OUT
+
VOH or VOL
CL
See Note A
GNDI
A.
+
VCM ±
±
GNDO
CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 17. Common-Mode Transient Immunity Test Circuit
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
17
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
8 Detailed Description
8.1 Overview
The ISO772x family of devices has an ON-OFF keying (OOK) modulation scheme to transmit the digital data
across a silicon dioxide based isolation barrier. The transmitter sends a high frequency carrier across the barrier
to represent one digital state and sends no signal to represent the other digital state. The receiver demodulates
the signal after advanced signal conditioning and produces the output through a buffer stage. These devices also
incorporate advanced circuit techniques to maximize the CMTI performance and minimize the radiated emissions
due the high frequency carrier and IO buffer switching. The conceptual block diagram of a digital capacitive
isolator, Figure 18, shows a functional block diagram of a typical channel.
8.2 Functional Block Diagram
Transmitter
TX IN
Receiver
OOK
Modulation
TX Signal
Conditioning
Oscillator
SiO2 based
Capacitive
Isolation
Barrier
RX Signal
Conditioning
Envelope
Detection
RX OUT
Emissions
Reduction
Techniques
Figure 18. Conceptual Block Diagram of a Digital Capacitive Isolator
Figure 19 shows a conceptual detail of how the OOK scheme works.
TX IN
Carrier signal through
isolation barrier
RX OUT
Figure 19. On-Off Keying (OOK) Based Modulation Scheme
18
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
8.3 Feature Description
The ISO772x family of devices is available in two channel configurations and default output state options to
enable a variety of application uses. Table 1 lists the device features of the ISO772x devices.
Table 1. Device Features
PART NUMBER
MAXIMUM DATA
RATE
CHANNEL
DIRECTION
DEFAULT OUTPUT
STATE
PACKAGE
RATED ISOLATION (1)
DW-16
5000 VRMS / 8000 VPK
ISO7720
100 Mbps
2 Forward, 0 Reverse
High
DWV-8
5000 VRMS / 7071 VPK
ISO7720F
ISO7721
ISO7721F
(1)
100 Mbps
100 Mbps
100 Mbps
2 Forward, 0 Reverse
1 Forward, 1 Reverse
1 Forward, 1 Reverse
Low
High
Low
D-8
3000 VRMS / 4242 VPK
DW-16
5000 VRMS / 8000 VPK
DWV-8
5000 VRMS / 7071 VPK
D-8
3000 VRMS / 4242 VPK
DW-16
5000 VRMS / 8000 VPK
DWV-8
5000 VRMS / 7071 VPK
D-8
3000 VRMS / 4242 VPK
DW-16
5000 VRMS / 8000 VPK
DWV-8
5000 VRMS / 7071 VPK
D-8
3000 VRMS / 4242 VPK
ISO7721B
100 Mbps
1 Forward, 1 Reverse
High
DW-16
5000 VRMS / 8000 VPK
ISO7721FB
100 Mbps
1 Forward, 1 Reverse
Low
DW-16
5000 VRMS / 8000 VPK
See the Safety-Related Certifications section for detailed isolation ratings.
8.3.1 Electromagnetic Compatibility (EMC) Considerations
Many applications in harsh industrial environment are sensitive to disturbances such as electrostatic discharge
(ESD), electrical fast transient (EFT), surge and electromagnetic emissions. These electromagnetic disturbances
are regulated by international standards such as IEC 61000-4-x and CISPR 22. Although system-level
performance and reliability depends, to a large extent, on the application board design and layout, the ISO772x
family of devices incorporates many chip-level design improvements for overall system robustness. Some of
these improvements include:
• Robust ESD protection cells for input and output signal pins and inter-chip bond pads.
• Low-resistance connectivity of ESD cells to supply and ground pins.
• Enhanced performance of high voltage isolation capacitor for better tolerance of ESD, EFT and surge events.
• Bigger on-chip decoupling capacitors to bypass undesirable high energy signals through a low impedance
path.
• PMOS and NMOS devices isolated from each other by using guard rings to avoid triggering of parasitic
SCRs.
• Reduced common mode currents across the isolation barrier by ensuring purely differential internal operation.
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
19
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
8.4 Device Functional Modes
Table 2 lists the functional modes for the ISO772x devices.
Table 2. Function Table (1)
VCCI
VCCO
PU
(1)
(2)
(3)
INPUT
(INx) (2)
OUTPUT
(OUTx)
H
H
L
L
Open
Default
Default mode: When INx is open, the corresponding channel output goes to the
default logic state. The default is High for ISO772x and Low for ISO772x with F
suffix.
Default mode: When VCCI is unpowered, a channel output assumes the logic
state based on the selected default option. The default is High for ISO772x and
Low for ISO772x with F suffix.
When VCCI transitions from unpowered to powered-up, a channel output
assumes the logic state of the input.
When VCCI transitions from powered-up to unpowered, channel output assumes
the selected default state.
COMMENTS
Normal Operation:
A channel output assumes the logic state of the input.
PU
PD
PU
X
Default
X
PD
X
Undetermined
When VCCO is unpowered, a channel output is undetermined (3).
When VCCO transitions from unpowered to powered-up, a channel output
assumes the logic state of the input
VCCI = Input-side VCC; VCCO = Output-side VCC; PU = Powered up (VCC ≥ 2.25 V); PD = Powered down (VCC ≤ 1.7 V); X = Irrelevant; H
= High level; L = Low level
A strongly driven input signal can weakly power the floating VCC via an internal protection diode and cause undetermined output.
The outputs are in undetermined state when 1.7 V < VCCI, VCCO < 2.25 V.
8.4.1 Device I/O Schematics
Input (Devices with F suffix)
Input (Devices without F suffix)
VCCI
VCCI
VCCI
VCCI
VCCI
VCCI
VCCI
1.5 M
985
985
INx
INx
1.5 M
Output
VCCO
~20
OUTx
Copyright © 2016, Texas Instruments Incorporated
Figure 20. Device I/O Schematics
20
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant the accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The ISO772x devices are high-performance, dual-channel digital isolators. The devices use single-ended CMOSlogic switching technology. The supply voltage range is from 2.25 V to 5.5 V for both supplies, VCC1 and VCC2.
When designing with digital isolators, keep in mind that because of the single-ended design structure, digital
isolators do not conform to any specific interface standard and are only intended for isolating single-ended
CMOS or TTL digital signal lines. The isolator is typically placed between the data controller (that is, μC or
UART), and a data converter or a line transceiver, regardless of the interface type or standard.
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
21
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
9.2 Typical Application
The ISO7721 device can be used with Texas Instruments' mixed signal microcontroller, digital-to-analog
converter, transformer driver, and voltage regulator to create an isolated 4-mA to 20-mA current loop.
VS
0.1 F
3.3 V
2
VCC D2 3
1:1.33
MBR0520L
1
SN6501
10 F
GND D1
0.1 F
IN
OUT
5 3.3VISO
10 F
TPS76333
3
1
EN
GND
2
10 F
MBR0520L
4, 5
ISO Barrier
0.1 F
0.1 F
20
LOOP+
0.1 F
0.1 F
15
0.1 F
10
3
8
2
5
6
VCC1
DVCC
XOUT
MSP430G2132
XIN
14
P3.0 11
12
P3.1
4
5
OUTA ISO7721
INB
GND1
DVSS
1, 7
4
VCC2
INA
OUTB
GND2
9, 16
13
5
12
4
3
VA
VD
LOW
BASE
ERRLVL
16
0.1 F
22
DBACK
DIN
C1
14
3 × 2.2 nF
1 F
DAC161P997
C2
13
C3 COMA
12
1
OUT
COMD
9
LOOP±
2
Copyright © 2017, Texas Instruments Incorporated
Figure 21. Isolated 4-mA to 20-mA Current Loop
22
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
Typical Application (continued)
9.2.1 Design Requirements
To design with these devices, use the parameters listed in Table 3.
Table 3. Design Parameters
PARAMETER
VALUE
Supply voltage, VCC1 and VCC2
2.25 V to 5.5 V
Decoupling capacitor between VCC1 and GND1
0.1 µF
Decoupling capacitor from VCC2 and GND2
0.1 µF
9.2.2 Detailed Design Procedure
Unlike optocouplers, which require external components to improve performance, provide bias, or limit current,
the ISO772x devices only require two external bypass capacitors to operate.
VCC1
VCC2
GND1 1
16 GND2
0.1 µF
0.1 µF
GND2
GND1
OUTA
NC
2
15
VCC1
3
14 VCC2
OUTA 4
INB
GND1
ISOLATION
GND1
13
NC
5
NC
6
11
NC
GND1 7
10
NC
8
INA
INA
INB
NC
GND2
12 OUTB
OUTB
9 GND2
GND2
Figure 22. Typical ISO7721 Circuit Hook-up
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
23
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
9.2.3 Application Curve
1 V/ div
1 V/ div
The following typical eye diagrams of the ISO772x family of devices indicate low jitter and wide open eye at the
maximum data rate of 100 Mbps.
Time = 3.5 ns / div
Time = 3.5 ns / div
Figure 23. ISO7720 Eye Diagram at 100 Mbps PRBS,
5-V Supplies and 25°C
Figure 24. ISO7721 Eye Diagram at 100 Mbps PRBS,
5-V Supplies and 25°C
9.2.3.1 Insulation Lifetime
Insulation lifetime projection data is collected by using industry-standard Time Dependent Dielectric Breakdown
(TDDB) test method. In this test, all pins on each side of the barrier are tied together creating a two-terminal
device and high voltage applied between the two sides; See Figure 25 for TDDB test setup. The insulation
breakdown data is collected at various high voltages switching at 60 Hz over temperature. For reinforced
insulation, VDE standard requires the use of TDDB projection line with failure rate of less than 1 part per million
(ppm). Even though the expected minimum insulation lifetime is 20 years at the specified working isolation
voltage, VDE reinforced certification requires additional safety margin of 20% for working voltage and 87.5% for
lifetime which translates into minimum required insulation lifetime of 37.5 years at a working voltage that's 20%
higher than the specified value.
Figure 26 shows the intrinsic capability of the isolation barrier to withstand high voltage stress over its lifetime.
Based on the TDDB data, the intrinsic capability of the insulation is 1500 VRMS with a lifetime of 135 years. Other
factors, such as package size, pollution degree, material group, etc. can further limit the working voltage of the
component. The working voltage of DW-16 and DWV-8 packages is specified up to 1500 VRMS and D-8 package
up to 450 VRMS. At the lower working voltages, the corresponding insulation lifetime is much longer than 135
years.
A
Vcc 1
Vcc 2
Time Counter
> 1 mA
DUT
GND 1
GND 2
VS
Oven at 150 °C
Figure 25. Test Setup for Insulation Lifetime Measurement
24
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
Figure 26. Insulation Lifetime Projection Data
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
25
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
10 Power Supply Recommendations
To help ensure reliable operation at data rates and supply voltages, a 0.1-μF bypass capacitor is recommended
at the input and output supply pins (VCC1 and VCC2). The capacitors should be placed as close to the supply pins
as possible. If only a single primary-side power supply is available in an application, isolated power can be
generated for the secondary-side with the help of a transformer driver such as Texas Instruments' SN6501 or
SN6505A. For such applications, detailed power supply design and transformer selection recommendations are
available in SN6501 Transformer Driver for Isolated Power Supplies or SN6505 Low-Noise 1-A Transformer
Drivers for Isolated Power Supplies.
11 Layout
11.1 Layout Guidelines
A minimum of four layers is required to accomplish a low EMI PCB design (see Figure 27). Layer stacking should
be in the following order (top-to-bottom): high-speed signal layer, ground plane, power plane and low-frequency
signal layer.
• Routing the high-speed traces on the top layer avoids the use of vias (and the introduction of their
inductances) and allows for clean interconnects between the isolator and the transmitter and receiver circuits
of the data link.
• Placing a solid ground plane next to the high-speed signal layer establishes controlled impedance for
transmission line interconnects and provides an excellent low-inductance path for the return current flow.
• Placing the power plane next to the ground plane creates additional high-frequency bypass capacitance of
approximately 100 pF/in2.
• Routing the slower speed control signals on the bottom layer allows for greater flexibility as these signal links
usually have margin to tolerate discontinuities such as vias.
If an additional supply voltage plane or signal layer is needed, add a second power or ground plane system to
the stack to keep it symmetrical. This makes the stack mechanically stable and prevents it from warping. Also the
power and ground plane of each power system can be placed closer together, thus increasing the high-frequency
bypass capacitance significantly.
For detailed layout recommendations, refer to the Digital Isolator Design Guide.
11.1.1 PCB Material
For digital circuit boards operating at less than 150 Mbps, (or rise and fall times greater than 1 ns), and trace
lengths of up to 10 inches, use standard FR-4 UL94V-0 printed circuit board. This PCB is preferred over cheaper
alternatives because of lower dielectric losses at high frequencies, less moisture absorption, greater strength and
stiffness, and the self-extinguishing flammability-characteristics.
11.2 Layout Example
High-speed traces
10 mils
Ground plane
40 mils
Keep this
space free
from planes,
traces, pads,
and vias
FR-4
0r ~ 4.5
Power plane
10 mils
Low-speed traces
Figure 27. Layout Example
26
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
12 Device and Documentation Support
12.1 Device Support
12.1.1 Development Support
For development support, refer to:
• Isolated CAN Flexible Data (FD) Rate Repeater Reference Design
• Isolated 16-Channel AC Analog Input Module Reference Design Using Dual Simultaneously Sampled ADCs
• Polyphase Shunt Metrology with Isolated AFE Reference Design
• Reference Design for Power-Isolated Ultra-Compact Analog Output Module
12.2 Documentation Support
12.2.1 Related Documentation
For related documentation, see the following:
• Texas Instruments, Digital Isolator Design Guide
• Texas Instruments, How to use isolation to improve ESD, EFT and Surge immunity in industrial systems
application report
• Texas Instruments, Isolation Glossary
• Texas Instruments, DAC161P997 Single-Wire 16-bit DAC for 4- to 20-mA Loops data sheet
• Texas Instruments, MSP430G2132 Mixed Signal Microcontroller data sheet
• Texas Instruments, SN6501 Transformer Driver for Isolated Power Supplies data sheet
• Texas Instruments, TPS76333 Low-Power 150-mA Low-Dropout Linear Regulators data sheet
12.3 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 4. Related Links
PARTS
PRODUCT FOLDER
ORDER NOW
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
ISO7720
Click here
Click here
Click here
Click here
Click here
ISO7721
Click here
Click here
Click here
Click here
Click here
12.4 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.5 Community Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
12.6 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
27
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
12.7 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
12.8 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
28
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
PACKAGE OUTLINE
D0008B
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
A
.004 [0.1] C
PIN 1 ID AREA
6X .050
[1.27]
8
1
2X
.150
[3.81]
.189-.197
[4.81-5.00]
NOTE 3
4X (0 -15 )
4
5
B
8X .012-.020
[0.31-0.51]
.150-.157
[3.81-3.98]
NOTE 4
.010 [0.25]
C A B
.069 MAX
[1.75]
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 -8
.016-.050
[0.41-1.27]
DETAIL A
.041
[1.04]
TYPICAL
4221445/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15], per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
29
ISO7720, ISO7721
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
www.ti.com
EXAMPLE BOARD LAYOUT
D0008B
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
8X (.055)
[1.4]
SEE
DETAILS
SYMM
SEE
DETAILS
SYMM
1
1
8
8X (.024)
[0.6]
8
SYMM
5
4
6X (.050 )
[1.27]
8X (.024)
[0.6]
(R.002 ) TYP
[0.05]
SYMM
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
(R.002 )
[0.05]
TYP
(.217)
[5.5]
HV / ISOLATION OPTION
.162 [4.1] CLEARANCE / CREEPAGE
IPC-7351 NOMINAL
.150 [3.85] CLEARANCE / CREEPAGE
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:6X
SOLDER MASK
OPENING
METAL
EXPOSDE
METAL
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
EXPOSED
METAL
.0028 MIN
[0.07]
ALL AROUND
.0028 MAX
[0.07]
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4221445/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
30
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
ISO7720, ISO7721
www.ti.com
SLLSEP3E – NOVEMBER 2016 – REVISED MARCH 2020
EXAMPLE STENCIL DESIGN
D0008B
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
8X (.055)
[1.4]
SYMM
SYMM
1
1
8
8X (.024)
[0.6]
6X (.050 )
[1.27]
8
SYMM
5
4
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
6X (.050 )
[1.27]
5
4
(R.002 )
[0.05]
TYP
(.217)
[5.5]
(.213)
[5.4]
HV / ISOLATION OPTION
.162 [4.1] CLEARANCE / CREEPAGE
IPC-7351 NOMINAL
.150 [3.85] CLEARANCE / CREEPAGE
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.127 MM] THICK STENCIL
SCALE:6X
4221445/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
Submit Documentation Feedback
Copyright © 2016–2020, Texas Instruments Incorporated
Product Folder Links: ISO7720 ISO7721
31
PACKAGE OPTION ADDENDUM
www.ti.com
25-Feb-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ISO7720D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7720
ISO7720DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7720
ISO7720DW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7720
ISO7720DWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7720
ISO7720DWV
ACTIVE
SOIC
DWV
8
64
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7720
ISO7720DWVR
ACTIVE
SOIC
DWV
8
1000
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7720
ISO7720FD
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7720F
ISO7720FDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7720F
ISO7720FDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7720F
ISO7720FDWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7720F
ISO7720FDWV
ACTIVE
SOIC
DWV
8
64
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7720F
ISO7720FDWVR
ACTIVE
SOIC
DWV
8
1000
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7720F
ISO7721BDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7721B
ISO7721BDWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7721B
ISO7721D
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7721
ISO7721DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7721
ISO7721DW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7721
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Feb-2020
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ISO7721DWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7721
ISO7721DWV
ACTIVE
SOIC
DWV
8
64
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7721
ISO7721DWVR
ACTIVE
SOIC
DWV
8
1000
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7721
ISO7721FBDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7721FB
ISO7721FBDWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7721FB
ISO7721FD
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7721F
ISO7721FDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7721F
ISO7721FDW
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7721F
ISO7721FDWR
ACTIVE
SOIC
DW
16
2000
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
ISO7721F
ISO7721FDWV
ACTIVE
SOIC
DWV
8
64
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7721F
ISO7721FDWVR
ACTIVE
SOIC
DWV
8
1000
Green (RoHS
& no Sb/Br)
NIPDAU
Level-2-260C-1 YEAR
-55 to 125
7721F
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of