LMK03806 Evaluation Board
User's Guide
November 2013
SNAU075A
LMK03806
Ultra-low Jitter Clock Generator with 14 Outputs
Evaluation Board Operating Instructions
2
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
CONTENTS
1. INTRODUCTION ......................................................................................................... 5
2. QUICK START ............................................................................................................ 6
3. DEFAULT CODELOADER MODES FOR EVALUATION BOARDS ......................... 7
4. EXAMPLE: USING CODELOADER TO PROGRAM THE LMK03806B ................... 8
5. PROGRAM/LOAD DEVICE ........................................................................................ 9
6. RESTORING A DEFAULT MODE .............................................................................. 9
7. VISUAL CONFIRMATION OF FREQUENCY LOCK ................................................ 10
8. ENABLE CLOCK OUTPUTS .................................................................................... 10
9. PLL LOOP FILTERS AND LOOP PARAMETERS .................................................. 11
10. EVALUATION BOARD INPUTS AND OUTPUTS .................................................. 12
12. CODELOADER USAGE ......................................................................................... 16
13. TYPICAL PHASE NOISE PERFORMANCE PLOTS ............................................. 23
14. SCHEMATICS ......................................................................................................... 27
15. PCB LAYERS STACKUP ....................................................................................... 35
16. PCB LAYOUT.......................................................................................................... 36
APPENDIX A: EVM SOFTWARE AND COMMUNICATION: INTERFACING UWIRE ... 41
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
3
LIST OF FIGURES
Figure 1: Quick Start Diagram ...................................................................................................................................... 6
Figure 2: Selecting a Default Mode for the LMK03806B Device .................................................................................. 7
Figure 4: Loading the Device ........................................................................................................................................ 9
Figure 5: Setting the Default mode for LMK03806 ....................................................................................................... 9
Figure 6: Setting Digital Delay, Clock Divider, Analog Delay, and Output Format for CLKout0 ................................. 10
Figure 7: Setting LVCMOS modes ............................................................................................................................. 10
Figure 8: Port Setup Tab............................................................................................................................................. 16
Figure 9: Clock Outputs Tab ....................................................................................................................................... 17
Figure 10: PLL Tab ..................................................................................................................................................... 18
Figure 11: Bits/Pins Tab.............................................................................................................................................. 20
Figure 12: Registers Tab ............................................................................................................................................ 22
Figure 13: LMK03806B PLL VCO div2 LVPECL Phase Noise................................................................................... 23
Figure 14: LMK03806B div8 CLKout LVPECL Phase Noise ...................................................................................... 25
Figure 15: LMK03806B div8 CLKout LVDS Phase Noise .......................................................................................... 25
Figure 16: LMK03806B div8 CLKout LVCMOS Phase Noise .................................................................................... 26
Figure 17 - LMK03806 Power Supply Schematic ....................................................................................................... 27
Figure 18 - LMK03806 Device Schematic .................................................................................................................. 28
Figure 19 - Outputs, (OSCout, CLKout0/1/2/3) Schematics ....................................................................................... 29
Figure 20 - LMK03806 Clock Outputs 4 through 7 Schematics ................................................................................. 30
Figure 21 - LMK03806 Clock Outputs 8 through 11 Schematics ............................................................................... 31
Figure 22: PCB Stackup ............................................................................................................................................. 35
Figure 23: Layer 1 - Top ............................................................................................................................................. 36
Figure 24: Layer 2 – RF Ground Plane ....................................................................................................................... 37
Figure 25: Layer 3 – Vcc Planes ................................................................................................................................. 38
Figure 26: Layer 4 - Bottom ........................................................................................................................................ 39
Figure 27: Top and Bottom (Composite) .................................................................................................................... 40
List of Tables
Table 1: EVM Contents ................................................................................................................................................. 5
Table 2: Default CodeLoader Modes for LMK03806 .................................................................................................... 7
Table 3: PLL Loop Filter Parameters for LMK03806B ................................................................................................ 11
Table 4: Evaluation Board Inputs and Outputs ........................................................................................................... 12
Table 5: Registers Controls and Descriptions in PLL Tab .......................................................................................... 18
Table 6: Datasheet to PCB Silkscreen Updates ......................................................................................................... 20
Table 7: Register Controls and Descriptions on Bits/Pins Tab ................................................................................... 21
Table 8: LMK03806B PLL VCO div2 Phase Noise and RMS Jitter (fs) ..................................................................... 23
Table 9: Typical Phase Noise Performance Plot Setup .............................................................................................. 24
Table 10: LMK03806B Phase Noise and RMS Jitter for Different CLKout Output Formats and Frequencies .......... 24
Table 11: Bill of Materials for LMK03806BEVAL Boards............................................................................................ 32
4
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
1. Introduction
The Texas Instruments LMK03806BEVAL evaluation module (EVM) helps designers evaluate the operation
and performance of the LMK03806B high performance, ultra low-jitter, multirate clock generator.
Texas Instruments CodeLoader software can be used to program the internal registers of the
LMK03806B device through the USB2ANY-uWire interface. The CodeLoader software will run
on a Windows 7 or Windows XP PC and can be downloaded from
http://www.ti.com/tool/codeloader
The EVM contains (See Table 1):
Table 1: EVM Contents
QUANTITY
November 2013
1
DESCRIPTION
LMK03806BEVAL
1
LKM03806 Quick Start Guide
1
Interface cables (LPT or USB)
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
5
2. Quick Start
1.
Connect a voltage of 5.0 volts to the Vcc SMA connector or terminal block. Device operates at
3.3 V using onboard LP3878-ADJ LDO.
2. Connect the uWire header via LPT or USB2ANY-uWire (See “EVM Software and
Communication” Section for more information).
3. Program the device with CodeLoader. CodeLoader is available for download at:
www.ti.com/tool/codeloader
a. Select correct LMK03806B from “Select Device Clock Conditioners” Menu.
b. Select a default mode from the “Mode” Menu. For the quick start use, “100 MHz
TCXO/XO Reference”
c. Ctrl-L must be pressed at least once to load all registers. Alternatively click menu Keyboard
Controls Load Device.
4. Measurements may be made at an active CLKout port via its SMA connector. Please see also
.
CLKout0
CLKout0*
CLKout2
CLKout2*
CL
CL Kou
Ko t 4
ut 4
*
0*
ut1
K o ut 10
L
C Ko
CL
LMK03806
uWire
header
CL
CL Kou
Ko t 8
ut 8
*
1
Power
5.0 V
(LDO)
OSCout0
OSCout0*
CL
K
CL out 6
Ko
ut 6 *
3
2
Program with CodeLoader
Be sure to press ‘Ctrl - L’
For interfacing
the board
please see
Appendix A
Laptop or PC
Figure 1: Quick Start Diagram
6
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
3. Default CodeLoader Modes for Evaluation Boards
CodeLoader saves the state of the selected LMK03806B device when exiting the software. To ensure a
common starting point, the following modes listed in Table 2: Default CodeLoader Modes for LMK03806
may be restored by clicking “Mode” and selecting the appropriate device configuration, as shown in
Figure 2 in the case of the LMK03806B device. Similar default modes are available for each
LMK03806B device in CodeLoader.
Figure 2: Selecting a Default Mode for the LMK03806B Device
After restoring a default mode, press Ctrl+L to program the device. The default modes also disable
certain outputs, so make sure to enable the output under test to make measurements.
Table 2: Default CodeLoader Modes for LMK03806
Default CodeLoader Mode
LMK03806B, 100 MHz
XO
Frequency
100 MHz
The next section outlines step-by-step procedures for using the evaluation board with the LMK03806B.
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
7
4. Example: Using CodeLoader to Program the LMK03806B
The purpose of this section is to walk the user through using CodeLoader 4 to make some measurements
with the LMK03806B device as an example. For more information on CodeLoader refer to CodeLoader
Usage or the CodeLoader 4 instructions located at http://www.ti.com/tool/codeloader.
Before proceeding, be sure to follow the Quick Start section to ensure proper connections.
1. Start CodeLoader 4 Application
Click “Start” “Programs” “CodeLoader 4” “CodeLoader 4”
The CodeLoader 4 program is installed by default to the CodeLoader 4 application group.
2. Select Device
Click “Select Device” “Clock Conditioners” “LMK03806B”
Once started CodeLoader 4 will load the last used device. To load a new device click “Select Device”
from the menu bar, then select the subgroup and finally device to load. For this example, the
LMK03806B is chosen. Selecting the device does cause the device to be programmed.
8
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
5. Program/Load Device
Assuming the Port Setup settings are correct, press the “Ctrl+L” shortcut or click “Keyboard Controls”
“Load Device” from the menu to program the device to the current state of the newly loaded LMK03806
file.
Figure 3: Loading the Device
Once the device has been initially loaded, CodeLoader will automatically program changed registers so it
is not necessary to re-load the device upon subsequent changes in the device configuration. It is possible
to disable this functionality by ensuring there is no checkmark by the “Options” “AutoReload with
Changes.”
Because a default mode will be restored in the next step, this step isn’t really needed but included to
emphasize the importance of pressing “Ctrl+L” to load the device at least once after starting CodeLoader,
restoring a mode, or restoring a saved setup using the File menu.
See CodeLoader Usage or the CodeLoader 4 instructions located at http://www.ti.com/tool/codeloader
for more information on Port Setup. Error! Reference source not found. contains information on
troubleshooting communications.
6. Restoring a Default Mode
Click “Mode” “100 MHz XO/TCXO Reference”; then press Ctrl+L.
Figure 4: Setting the Default mode for LMK03806
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
9
For the purpose of this walkthrough, a default mode will be loaded to ensure a common starting point.
This is important because when CodeLoader is closed, it remembers the last settings used for a particular
device. Again, remember to press Ctrl+L as the first step after loading a default mode.
7. Visual Confirmation of Frequency Lock
After a default mode is restored and loaded, LED D4, should illuminate red when the PLL is locked to the
reference crystal.
8. Enable Clock Outputs
While the LMK03806B offers programmable clock output buffer formats, the evaluation board is shipped
with preconfigured output terminations to match the default buffer type for each output. Refer to the
CLKout port description in the Evaluation Board Inputs and Outputs section.
To measure phase noise at one of the clock outputs, for example, CLKout0:
1. Click on the Clock Outputs tab,
2. Uncheck “Powerdown” in the Divider Powerdown box to enable the channel,
3. Set the following settings as needed:
a. Clock Divider value
b. Clock Output type.
Figure 5: Setting Digital Delay, Clock Divider, Analog Delay, and Output Format for
CLKout0
4. Depending on the configured output type, the clock output SMAs can be interfaced to a test
instrument with a single-ended 50-ohm input as follows.
a. For LVDS:
i. A balun (like ADT2-1T) is recommended for differential-to-single-ended
conversion.
b. For LVPECL:
i. A balun can be used, or
ii. One side of the LVPECL signal can be terminated with a 50-ohm load and the
other side can be run single-ended to the instrument.
c. For LVCMOS:
i. There are two single-ended outputs, CLKoutX and
CLKoutX*, and each output can be set to Normal, Inverted,
or Off. There are nine (9) combinations of LVCMOS
modes in the Clock Output list.
ii. One side of the LVCMOS signal can be terminated with a
50-ohm load and the other side can be run singleFigure 6: Setting LVCMOS
ended to the instrument.
iii. A balun may also be used. Ensure CLKoutX and CLKoutX* states are
complementary, i.e.: Norm/Inv or Inv/Norm.
5. The phase noise may be measured with a spectrum analyzer or signal source analyzer.
10
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
See Typical Phase Noise Performance Plots for phase noise plots of the clock outputs. TI’s Clock Design
Tool can be used to calculate divider values to achieve desired clock output frequencies. See:
http://www.ti.com/tool/codeloader.
9. PLL Loop Filters and Loop Parameters
The default loop filter for the PLL has been configured for a 60 kHz bandwidth. The following table
contains the parameters for the PLL.
TI’s Clock Design Tool can be used to optimize PLL phase noise/jitter for given specifications. See:
http://www.ti.com/tool/codeloader.
PLL Loop Filter
Table 3: PLL Loop Filter Parameters for LMK03806B
Integrated VCO PLL
20 MHz Reference
0.022
C1_LF
18
C2_LF
0.01
C3 (internal)
0.01
C4 (internal)
0.82
R2_A2
0.2
R3 (internal)
0.2
R4 (internal)
Charge
Pump
3.2
Current, K
Phase
20
Detector
Frequency
2500
Frequency
19
Kvco
25
N
5
P
Phase
75
Margin
Loop
63
Bandwidth
100 MHz Reference
.022
18
0.01
0.01
0.82
0.2
0.2
nF
nF
nF
nF
kΩ
kΩ
kΩ
3.2
mA
100
MHz
2400
19
12
2
MHz
MHz/V
70
degrees
60
kHz
Note: PLL Loop Bandwidth is a function of K, Kvco, N as well as loop components. Changing K and
N will change the loop bandwidth.
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
11
10. Evaluation Board Inputs and Outputs
The following table contains descriptions of the inputs and outputs for the evaluation board. Unless
otherwise noted, the connectors described can be assumed to be populated by default. Additionally,
some applicable CodeLoader programming controls are noted for convenience.
Table 4: Evaluation Board Inputs and Outputs
Connector Name
Signal Type,
Input/Output
Description
Clock outputs with programmable output buffers.
The output terminations by default on the evaluation
board are shown below, and the output type selected
by default in CodeLoader is indicated by an asterisk
(*):
Clock output pair
SMAs Populated:
CLKout0, CLKout0*,
CLKout2, CLKout2*,
CLKout4, CLKout4*,
CLKout6, CLKout6*,
CLKout8, CLKout8*,
CLKout10, CLKout10*
SMAs Not Populated:
CLKout1, CLKout1*,
CLKout3, CLKout3*,
CLKout5, CLKout5*,
CLKout7, CLKout7*,
CLKout9, CLKout9*,
CLKout11, CLKout11*
Analog,
Output
CLKout0
CLKout1
CLKout2
CLKout3
CLKout4
CLKout5
CLKout6
CLKout7
CLKout8
CLKout9
CLKout10
CLKout11
Default Board
Termination
LVPECL*
LVPECL
LVPECL*
LVPECL
LVDS* / LVCMOS
LVDS / LVCMOS
LVDS* / LVCMOS
LVDS / LVCMOS
LVDS* / LVCMOS
LVDS / LVCMOS
LVPECL*
LVPECL
Each CLKout pair has a programmable LVDS,
LVPECL, or LVCMOS buffer. The output buffer
type can be selected in CodeLoader in the Clock
Outputs tab via the CLKoutX_TYPE control.
All clock outputs are AC-coupled to allow safe
testing with RF test equipment.
All LVPECL clock outputs are source-terminated
using 240-ohm resistors.
If an output pair is programmed to LVCMOS, each
output can be independently configured (normal,
inverted, or off/tri-state).
12
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
Connector Name
Signal Type,
Input/Output
Description
Buffered outputs of OSCin port.
The output terminations on the evaluation board are
shown below, the output type selected by default in
CodeLoader is indicated by an asterisk (*):
Default Board
OSC output pair
Termination
OSCout0
LVPECL* (fixed)
OSCout1
LVPECL* (fixed)
OSCout0, OSCout0*,
OSCout1, OSCout1*
Analog,
Output
Only OSCout0 has a programmable LVDS,
LVPECL, or LVCMOS output buffer. The OSCout0
buffer type can be selected in CodeLoader on the
Clock Outputs tab via the OSCout0_TYPE control.
OSCout1 has LVPECL buffer only but has
programmable swing amplitude.
Both OSCout pairs are AC-coupled to allow safe
testing with RF test equipment.
The OSCout0 and OSCout1 outputs are sourceterminated using 240-ohm resistors.
If OSCout0 is programmed as LVCMOS, each
output can be independently configured (normal,
inverted, inverted, and off/tri-state).
Main power supply input for the evaluation board.
A 3.9 V DC power source applied to this SMA will,
by default, source the onboard LDO regulators that
power the inner layer planes that supply the
LMK03806B.
Vcc
Power,
Input
The LMK03806B contains internal voltage
regulators for the VCO, PLL and other internal
blocks. The clock outputs do not have an internal
regulator, so a clean power supply with sufficient
output current capability is required for optimal
performance.
On-board LDO regulators and 0 resistor options
provide flexibility to supply and route power to
various devices. See schematics for more details.
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
13
Connector Name
Signal Type,
Input/Output
J1
Power,
Input
Description
Alternative power supply input for the evaluation
board using two unshielded wires (Vcc and GND).
Apply power to either Vcc SMA or J1, but not both.
By default, these SMAs are not connected to the
traces going to the OSCin/OSCin* pins of the
LMK03806B. Instead, the onboard crystal drives the
OSCin input of the device.
OSCin, OSCin*
Analog,
Input
A single-ended or differential signal may be used to
drive the OSCin/OSCin* pins and must be AC
coupled. If operated in single-ended mode, the
unused input must be connected to GND with 0.1 uF.
Refer to the LMK03806 Datasheet section
“Electrical Characteristics” for PLL Reference Input
(OSCin) specifications.
10-pin header for uWire programming interface and
programmable logic I/O pins for the LMK03806B.
uWire
CMOS,
Input/Output
The uWire interface includes CLKuWire,
DATAuWire, and LEuWire signals.
The programmable logic I/O signals accessible
through this header include: SYNC. SYNC also has
a dedicated SMA and test point.
Programmable status I/O pin. By default, set as an
input pin for synchronize the clock outputs with a
fixed and known phase relationship between each
clock output selected for SYNC.
SYNC
CMOS,
Input/Output
In the default CodeLoader mode, SYNC will asserted
when the SYNC pin is low and the outputs to be
synchronized will be held in a logic low state. When
SYNC is unasserted, the clock outputs to be
synchronized are activated and will be initially phase
aligned with each other except for outputs
programmed with different digital delay values.
A SYNC event can also be programmed by toggling
the SYNC_POL_INV bit in the Bits/Pins tab in
CodeLoader.
Refer to the LMK03806 Datasheet section “Clock
Output Synchronization” for more information.
14
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
11. Recommended Test Equipment
Power Supply
The Power Supply should be a low noise power supply, particularly when the devices on the board are
being directly powered (onboard LDO regulators bypassed).
Phase Noise / Spectrum Analyzer
To measure phase noise and RMS jitter, an Agilent E5052 Signal Source Analyzer is recommended.
An Agilent E4445A PSA Spectrum Analyzer with the Phase Noise option is also usable although the
architecture of the E5052 is superior for phase noise measurements. At frequencies less than 100
MHz the local oscillator noise of the E4445A is too high and measurements will reflect the E4445A’s
internal local oscillator performance, not the device under test.
Oscilloscope
To measure the output clocks for AC performance, such as rise time or fall time, propagation delay, or
skew, it is suggested to use a real-time oscilloscope with at least 1 GHz analog input bandwidth (2.5+
GHz recommended) with 50 ohm inputs and 10+ Gsps sample rate. To evaluate clock
synchronization or phase alignment between multiple clock outputs, it’s recommended to use phasematched, 50-ohm cables to minimize external sources of skew or other errors/distortion that may be
introduced if using oscilloscope probes.
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
15
12. CodeLoader Usage
Code Loader is used to program the evaluation board with either an LPT or USB2ANY-uWire interface
available from http://www.ti.com.
Port Setup Tab
Figure 7: Port Setup Tab
On the Port Setup tab, the user may select the type of communication port (LPT or USB) that will be used
to program the device on the evaluation board.
The Pin Configuration field is hardware dependent and normally does not need to be changed by the user.
Figure 7: Port Setup Tab shows the default settings.
16
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
Clock Outputs Tab
Figure 8: Clock Outputs Tab
The Clock Outputs tab allows the user to control the output channel blocks, including:
Clock Group Source from either Crystal or OSCin
Channel Powerdown (affects clock divider, and buffer blocks)
Clock Divide value
Clock Output format (per output)
Clicking on the cyan-colored PLL block that contains R, PDF and N values will bring the PLL tab into
focus where these values may be modified, if needed.
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
17
Clicking on the values in the box containing the Internal Loop Filter component (R3, C3, R4, C4) allow
one to step through the possible values. Left click to increase the component value, and right click to
decrease the value. These values can also be changed in the Bits/Pins tab.
The Reference Oscillator value field may be changed in either the Clock Outputs tab or the PLL tab.
The PLL Reference frequency should match the frequency of the onboard Crystal.
PLL Tab
Figure 9: PLL Tab
The PLL tab allows the user to change the following parameters in Table 5.
Table 5: Registers Controls and Descriptions in PLL Tab
Control Name
Reference Oscillator
Frequency (MHz)
Phase Detector Frequency
(MHz)
Register Name
OSCin_FREQ
VCO Frequency (MHz)
n/a
18
SNAU075A
n/s
Description
OSCin frequency from the External OSCin
connector or Crystal.
PLL Phase Detector Frequency (PDF). This
value is calculated as:
PLL PDF = OSCin Frequency
*(2EN_PLL_REF_2X) / (PLL_R).
Internal VCO Frequency should be within
the allowable range of the LMK03806B
device.
This value is calculated as:
VCO Frequency = PLL PDF * (PLL_N *
PLL_P).
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
Doubler
EN_PLL_REF_2X
R Counter
N Counter
OSCout Divider
Phase Detector Polarity
PLL_R
PLL_N
PLL_P
PLL_CP_POL
Charge Pump Gain
PLL_CP_GAIN
Charge Pump State
PLL_CP_TRI
PLL Doubler.
0 = Bypass Doubler
1 = Enable Doubler
PLL R Counter value (1 to 4095).
PLL N Counter value (1 to 49140).
PLL N Prescaler value (2 to 8).
PLL Phase Detector Polarity.
Click on the polarity sign to toggle polarity
“+” or “–”.
PLL Charge Pump Gain.
Left-click/right-click to increase/decrease
charge pump gain (100, 400, 1600, 3200
uA).
PLL Charge Pump State.
Click to toggle between Active and Tri-State.
Changes made on this tab will be reflected in the Clock Outputs tab. The VCO Frequency should
conform to the specified internal VCO frequency range for the LMK03806B.
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
19
Bits/Pins Tab
Figure 10: Bits/Pins Tab
The Bits/Pins tab allows the user to program bits directly, many of which are not available on other tabs.
Brief descriptions for the controls on this tab are provided in Table 7: Register Controls and Descriptions
on Bits/Pins Tab to supplement the datasheet. Refer to the LMK03806 Datasheet for more information.
TIP: Right-clicking any register name in the Bits/Pins tab will display a Help prompt with the register
address, data bit location/length, and a brief register description.
Note: Table 6 shows some differences between the datasheet names and PCB names for -002 PCB’s:
Table 6: Datasheet to PCB Silkscreen Updates
Datasheet Name
Readback (pin 27)
Ftest/LD (pin 33)
GPout0 (pin 62)
GPout1 (pin 63)
20
SNAU075A
PCB Silkscreen Identifier
Status0
Status1
Status2
Status3
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
Table 7: Register Controls and Descriptions on Bits/Pins Tab
Mode Control
Group
IO Control – Sync
Output Control
Automatic
Update
Crystal
Register Name
RESET
POWERDOWN
uWire_LOCK
OSCin_FREQ
PLL_N_CAL
EN_PLL_XTAL
READBACK_TYPE
LD_MUX
LD_TYPE
GPO0
GPO1
SYNC_TYPE
SYNC_POL_INV
SYNC_PLL_DLD
NO_SYNC_CLKoutX_Y
PLL_DLD_CNT
PLL
EN_PLL_REF_2X
Program Pins
PLL_R3_LF
PLL_R4_LF
PLL_C3_LF
PLL_C4_LF
SYNC
TRIGGER
November 2013
Description
Resets the device to default register values. RESET
must be cleared for normal operation to prevent an
unintended reset every time R0 is programmed.
Places the device in powerdown mode.
When checked, no other uWire programming will
have effect. Must be unchecked to enable uWire
programming of registers R0 to R30.
Sets the OSCin frequency range.
Sets the PLL_N value.
Enables Crystal Oscillator.
Readback pin type. (Labeled Stats0 on PCB)
Ftest/LD pin selection when output. (Ftest/LD
output labeled Status1 on PCB)
Sets I/O pin type on the LD pin.
Sets logic level on the GPO0 pin. (Labeled Status2
on PCB)
Sets logic level on the GPO1 pin. (Labeled Status3
on PCB)
Sets I/O pin type on the SYNC pin.
Sets polarity on SYNC input to active low when
checked. Toggling this bit will initiate a SYNC
event.
Engage SYNC mode until PLL DLD is true
Synchronization will not affect selected clock
outputs, where X = even-numbered output and Y =
odd-numbered output.
The reference and feedback of PLL must be within
the window of phase error as specified by
PLL_WND_SIZE for this many cycles before PLL
digital lock detect is asserted.
Enables the doubler block to doubles the reference
frequency into the PLL R counter. This can allow
for frequency of 2/3, 2/5, etc. of OSCin to be used
at the phase detector of PLL.
Set the corresponding integrated PLL loop filter
values: R3, R4, C3, and C4.
It is also possible to set these values by clicking on
the loop filter values on the Clock Outputs tab.
Sets these pins on the uWire header to logic high
(checked) or logic low (unchecked).
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
21
Registers Tab
Figure 11: Registers Tab
The Registers tab shows the value of each register. This is convenient for programming the device to the
desired settings, then exporting to a text file the register values in hexadecimal for use in your own
application.
By clicking in the “bit field” it is possible to manually change the value of registers by typing ‘1’ and ‘0.’
22
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
13. Typical Phase Noise Performance Plots
PLL
Figure 12: LMK03806B PLL VCO div2 LVPECL Phase Noise
Table 8: LMK03806B PLL VCO div2 Phase Noise and RMS Jitter (fs)
Offset
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
10 MHz
20 MHz
RMS Jitter (fs)
12 kHz to 20 MHz
RMS Jitter (fs)
100 Hz to 20 MHz
November 2013
Phase Noise (dBc/Hz)
-98.3
-107.8
-106.6
-114.2
-136.6
-150.6
-151.3
215
229
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
23
Clock Outputs (CLKout)
The LMK03806 Family features programmable LVDS, LVPECL, and LVCMOS buffer modes for the
CLKoutX and OSCout0 output pairs. The OSCout1 output pair has a LVPECL buffer. Included below
are various phase noise measurements for each output format.
CLKout Phase Noise (div8 and div16)
For the LMK03806B, the internal VCO frequency is 2400 MHz. The divide-by-8 CLKout frequency is
312.5 MHz, and the divide-by-16 CLKout frequency is 156.25 MHz.
Table 9: Typical Phase Noise Performance Plot Setup
Parameter
LMK03806B Mode
Loop Filter Parameters
CLKout for LVDS/LVCMOS
CLKout for LVPECL
Condition
100 MHz TCXO/XO Reference
As shown under “100 MHz Reference” in Table 3
CLKout8, with CLKout8* terminated in to 50 Ω
CLKout10, with CLKout10* terminated in to 50 Ω
Table 10: LMK03806B Phase Noise and RMS Jitter for Different CLKout Output Formats and
Frequencies
Offset
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
10 MHz
20 MHz
RMS Jitter (fs)
12 kHz to 20 MHz
RMS Jitter (fs)
100 Hz to 20 MHz
24
SNAU075A
div8
LVPECL
-91.9
-113.8
-122.6
-128.7
-148.1
-157.6
-157.7
div8
LVDS
-92.0
-113.2
-122.7
-128.9
-147.7
-155.0
-155.1
div8
LVCMOS
-93.2
-113.4
-122.5
-128.4
-148.2
-157.2
-157.2
div16
LVPECL
-98.6
-119.8
-128.7
-134.8
-153.7
-160.5
-160.7
div16
LVDS
-98.8
-119.3
-128.4
-134.9
-153.0
-158.0
-158.1
div16
LVCMOS
-97.1
-119.0
-128.4
-134.4
-153.7
-160.4
-160.4
141.1
144.0
143.2
145.3
155.4
149.8
206.1
210.5
210.2
208.8
217.1
224.4
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
Figure 13: LMK03806B div8 CLKout LVPECL Phase Noise
Figure 14: LMK03806B div8 CLKout LVDS Phase Noise
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
25
Figure 15: LMK03806B div8 CLKout LVCMOS Phase Noise
26
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
14. Schematics
Power Supplies
1
2
3
4
5
6
Power Plane for LMK Except Outputs
VccCore_TP
TESTPOINT
VccCore
C41
0.1µF
Vcc Core Supplies Vcc1-VCO, Vcc4-Digital, Vcc5-CLKin, Vcc6-PLL, Vcc7-OSCout0, and Vcc9-PLL2
A
A
R81
120 FB
Direct Power
VccTP
Vcc
Vcc
R82
DNP
1000
1
TESTPOINT
C42
0.1µF
VccCore
C43
10µF
2
3
4
5
142-0701-201
Vcc8_PDCP2
C44
1µF
C45
0.1µF
J1
1
2
1
2
TERMBLOCK_2
Power Planes for LMK CLKout Outputs
TESTPOINT
VccCLKout_TP
B
R83
DNP
1000
VccCLKout
R84
C46
10µF
C47
1µF
0
C48
0.1µF
R86
0
R88
0
Vcc2_CG1_p17
DNPC49
470pF
Vcc3_CG2_p18
DNPC50
0.1µF
Vcc10_CG3_p47
DNPC51
470pF
R85
120 FB
R87
120 FB
R89
120 FB
B
Vcc2_CLKout_CG1
Vcc3_CLKout_CG2
Vcc10_CLKout_CG3
LDO Power Options
C
VccLDOin
C
R90
R92
0
0
LP3878SD-ADJ
V_LM3878-ADJ
U2
4
C53
4.7µF
R94
51k
8
2
7
9
IN
SD
OUT
ADJ
NC
BYP
NC
DAP GND
R93
5
C54
R97
2200pF 2.00k
1
C55
1µF
C56
10µF
R98
C58
0.1µF
LP3878SD-ADJ
R95
VccCLKout
0
120
3
R99
866
R100
0
LP3878-ADJ 3.3 V component values:
C340 = 4.7 uF
R351= 2.00 k
C346 = 0.01 uF
R356= 866
C352 = 10 uF
R350= 51 k
C341 = 2.2 nF
D
Vcc12_CG5_p57
DNPC57
470pF
Vcc13_CG0_p64
DNPC59
0.1µF
2
120 FB
Vcc11_CLKout_CG4
R96
120 FB
R101
120 FB
Vcc12_CLKout_CG5
Vcc13_CLKout_CG0
D
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this
specification or any information contained therein. Texas Instruments and/or its licensors do not
warrant that this design will meet the specifications, will be suitable for your application or fit for
any particular purpose, or will operate in an implementation. Texas Instruments and/or its
licensors do not warrant that the design is production worthy. You should completely validate
and test your design implementation to confirm the system functionality for your application.
1
R91
VccCore
120
6
Vcc11_CG4_p52
DNPC52
0.1µF
3
4
Mod. Date: 11/28/2011
Designed for: Evaluation Customer
Project: LMK038xx Evaluation Board
Sheet Title: Power Supplies
Sheet: 2 of 9
Size: B
Schematic: 870600688
Rev: 1.1
Assembly Variant: Customer Eval - 2011-11-22
File: Power.SchDoc
Contact: http://www.national.com/support
5
http://www.ti.com
© Texas Instruments CopyrightYear
6
Figure 16 - LMK03806 Power Supply Schematic
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
27
LMK03806B Device with Loop Filter and Crystal Circuits
1
2
D1
R1
DNP
270
3
4
5
R2
DNP
270
Red
uWire Header and Level Translation
D2
uWire
Red
Status3_TP
Status2_TP
TESTPOINT
A
TESTPOINT
TESTPOINT
Vcc13_CLKout_CG0
6
Vcc12_CLKout_CG5
R3
15k
PLL Loop Filters
Vcc11_CLKout_CG4
10
8
6
4
2
LEuWire_TP
uWire_LE
R4
27k
DNPC1
100pF
9
7
5
3
1
HEADER_2X5
CLKout7_N
CLKout6_P
CLKout6*
CLKout7_P
CLKout6_N
49
50
51
CLKout7
CLKout7*
Vcc11
CLKout8_N
CLKout9_N
CLKout8_P
52
53
CLKout8
54
CLKout8*
55
CLKout9_P
CLKout9
CLKout9*
CLKout10_P
DAP PAD
Vcc7
LDObyp2
OSCin*
CLKout2
OSCin
TESTPOINT
OSCout1*
Vcc5
OSCout1
31
30
OSCout1_P
Status0_TP
Ftest/LD
CLKuWire_TP
IC_SYNC
DNP
DNPC2
100pF
R7
uWire_CLK
R6
27k
SMA
15k
R8
27k
DNPC3
100pF
48
Vcc10_CLKout_CG3
47
TESTPOINT
46
uWire_DATA
45
uWire_CLK
44
43
uWire_LE
15k
uWire_LE
C5
R11
DNP
0
C6
OSCout0_N
39
OSCout0_P
VccCore
C63
18
0.1µF
OSCin_N
36
OSCin_P
DNP
R14
270
R15
270
SMA
Y1
DNP
37
B
OSCin*
R12
R16
DNP
0
22pF
38
R10
27k
DNPC4
100pF
Vcc8_PDCP2
40
35
R9
uWire_CLK
42
41
DATAuWire_TP
uWire_DATA
uWire_DATA
VccCore
DNP
1µF
Y2
DNP
DNP
R17
DNP
100
VccCore
34
Status1_TP
33
R20
270
TESTPOINT
R18
0
C9
DNP
22pF
D3
OSCout1_N 32
NC
29
NC
28
27
22
CLKout5_P
Vcc2
Vcc3
18
17
Vcc2_CLKout_CG1
NC
CLKout3
C
Readback
NC
NC
Vcc6
CLKout3*
CLKout5
CLKout2*
CLKout5*
CLKout3_P 16
OSCout0
0
LDObyp1
21
CLKout3_N 15
Vcc1
CLKout5_N
CLKout2_N 14
OSCout0*
CLKout4*
CLKout2_P 13
C8
0.1µF
Vcc8
NC
CLKout4
12
C7
10µF
CPout
LMK03806
20
11
56
Vcc9
19
0.1µF
Vcc12
CLKout10_N
SYNC*
CLKout4_N
10
DNP
57
LEuWire
CLKout4_P
C62 VccCore
58
CLKout11_N
NC
7
TESTPOINT
NC
R300
DNP
51
8
NC
9
CLKout10
59
CLKout10*
61
60
CLKout11*
62
GPout0
CLKuWire
26
IC_SYNC
CLKout1
Vcc4
5
SYNC_TP
6
DATAuWire
25
B
CLKout1*
TESTPOINT
C2_LF
0.018µF
R2_LF
820
Vcc10
GND
CLKout1_P 4
DNPC2pLF
C1_LF
220pF
220pF
A
R5
15k
IC_SYNC
XTAL-mode Loop Filter
CLKout6
CLKout0*
24
CLKout1_N 3
CLKout0
23
CLKout0_N 2
CLKout11
64
Vcc13
CLKout0_P 1
GPout1
U1
LMK03806
63
CLKout11_P
VTUNE_TP
R19
270
C10
R22
DNP
0
C
OSCin
DNP
18
0.1µF
Green
R21
270
R23
DNP
SMA
Y3
3
Out
GND
2
DNPC64
R24
0.1µF 270
4
Vcc3_CLKout_CG2
VccCore
D4
VccCore
DNPC65
1µF
Red
Vcc Vcont
1
C60
TCXO
0.1µF R104
0
VccCore
R102
1.00k
R103
1.00k
C61
0.1µF
VccCore
D
D
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this
specification or any information contained therein. Texas Instruments and/or its licensors do not
warrant that this design will meet the specifications, will be suitable for your application or fit for
any particular purpose, or will operate in an implementation. Texas Instruments and/or its
licensors do not warrant that the design is production worthy. You should completely validate
and test your design implementation to confirm the system functionality for your application.
1
2
3
4
Mod. Date: 11/30/2011
Designed for: Evaluation Customer
Project: LMK038xx Evaluation Board
Sheet Title: Main Sheet / IC
Sheet:3 of 9
Size: B
Schematic: 870600688
Rev: 1.1
Assembly Variant: Customer Eval - 2011-11-22
File: LMK03806_PLL.SchDoc
Contact: http://www.national.com/support
5
http://www.ti.com
© Texas Instruments CopyrightYear
6
Figure 17 - LMK03806 Device Schematic
28
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
Outputs, (OSCout0/1, CLKout0/1/2/3)
1
2
3
4
5
6
OSCout0 Default: LVDS, AC coupled
OSCout1
Default: LVPECL, AC coupled
R26
DNP
51
A
OSCout0_1_P
OSCout0_P
R27
240
R25
DNP
51
OSCout1
C11
OSCout0
C12
OSCout1_1_P
OSCout1_P
SMA
C13
240
0.1uF
SMA
A
0.1µF
GND
GND
OSCout1*
C14
OSCout0*
C15
OSCout0_1_N
OSCout0_N
R28
240
OSCout1_1_N
OSCout1_N
SMA
C16
240
0.1µF
SMA
0.1µF
R29
DNP
51
R30
DNP
51
GND
GND
CLKout2
CLKout0
Default: LVPECL, AC coupled
B
CLKout1
R31
DNP
51
CLKout0
C17
CLKout0_1_P
CLKout0_P
R34
240
SMA
Default: LVPECL, AC coupled
Default: LVPECL, AC coupled
R33
51
CLKout1_1_N
CLKout1_N
0.1µF
R36
240
GND
DNP
0.1µF
SMA
R35
240
CLKout0_1_N
R37
240
SMA
0.1µF
GND
SMA
0.1µF
GND
C22
CLKout1_P
R39
240
R40
DNP
51
B
CLKout2
CLKout2_1_P
CLKout2_P
GND
CLKout0*
C20
CLKout0_N
R32
DNP
51
C18
CLKout1*
C19
CLKout2*
C21
CLKout1
CLKout1_1_P
SMA
DNP
CLKout2_1_N
CLKout2_N
R38
240
0.1µF
R42
51
SMA
0.1µF
R41
DNP
51
GND
GND
CLKout3
C
C
Default: LVPECL, AC coupled
C23
CLKout3_N
R44
240
0.1µF
R43
51
CLKout3*
CLKout3_1_N
SMA
DNP
GND
C24
CLKout3_P
R45
240
0.1µF
CLKout3
CLKout3_1_P
SMA
DNP
R46
51
GND
D
D
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this
specification or any information contained therein. Texas Instruments and/or its licensors do not
warrant that this design will meet the specifications, will be suitable for your application or fit for
any particular purpose, or will operate in an implementation. Texas Instruments and/or its
licensors do not warrant that the design is production worthy. You should completely validate
and test your design implementation to confirm the system functionality for your application.
1
2
3
4
Mod. Date: 11/28/2011
Designed for: Evaluation Customer
Project: LMK038xx Evaluation Board
Sheet Title: Clock Outputs 1/3
Sheet:6 of 9
Size: B
Schematic: 870600688
Rev: 1.1
Assembly Variant: Customer Eval - 2011-11-22
File: OutClks0.SchDoc
Contact: http://www.national.com/support
5
Figure 18 - Outputs, (OSCout, CLKout0/1/2/3) Schematics
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
http://www.ti.com
© Texas Instruments CopyrightYear
6
29
Clock Outputs (CLKout 4/5/6/7)
1
A
2
3
CLKout4
4
R48
51
CLKout4
C25
CLKout4_1_P
CLKout4_P
R49
DNP
240
CLKout4_1_N
R51
DNP
240
0.1µF
CLKout5_1_P
R52
DNP
240
R53
DNP
51
DNP
0.1µF
SMA
R54
51
GND
CLKout6
Default: LVDS or LVCMOS, AC coupled
DNP
51
CLKout6
C29
R57
CLKout6_2_P
R58
DNP
240
CLKout6_1_P
C30
CLKout7_N
SMA
0.1µF
R59
DNP
240
GND
0.1µF
R56
51
CLKout7*
CLKout7_1_N
SMA
DNP
GND
C31
CLKout6_2_N
R60
B
CLKout7
Default: LVDS or LVCMOS, AC coupled
R55
R61
DNP
240
C
CLKout6*
CLKout6_1_N
C32
CLKout7_P
SMA
0.1µF
R62
DNP
240
R63
DNP
51
GND
D
SMA
CLKout5
C28
CLKout5_P
SMA
GND
33
DNP
0.1µF
GND
CLKout4*
C27
CLKout6_N
CLKout5_1_N
R50
DNP
240
GND
C
CLKout5*
C26
CLKout5_N
SMA
0.1µF
CLKout4_N
33
A
Default: LVDS or LVCMOS, AC coupled
R47
DNP
51
CLKout6_P
6
CLKout5
Default: LVDS or LVCMOS, AC coupled
B
5
0.1µF
CLKout7
CLKout7_1_P
SMA
DNP
R64
51
GND
Notes:
D
1. Designators greater than and equal to 300 are placed on bottom of PCB
1
2
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this
specification or any information contained therein. Texas Instruments and/or its licensors do not
warrant that this design will meet the specifications, will be suitable for your application or fit for
any particular purpose, or will operate in an implementation. Texas Instruments and/or its
licensors do not warrant that the design is production worthy. You should completely validate
and test your design implementation to confirm the system functionality for your application.
3
4
Designed for: Evaluation Customer
Mod. Date: 11/28/2011
Project: LMK038xx Evaluation Board
Sheet Title: Clock Outputs 2/3
Sheet:7 of 9
Size: B
Schematic: 870600688
Rev: 1.1
Assembly Variant: Customer Eval - 2011-11-22
File: OutClks1.SchDoc
Contact: http://www.national.com/support
5
Figure 19 - LMK03806 Clock Outputs 4 through 7 Schematics
30
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
http://www.ti.com
© Texas Instruments CopyrightYear
6
November 2013
Clock Outputs (CLKout8/9/10/11)
1
A
2
3
CLKout8
6
R66
51
CLKout8
C33
CLKout8_1_P
CLKout8_P
A
Default: LVDS or LVCMOS, AC coupled
R65
DNP
51
C34
CLKout9_N
SMA
0.1µF
R68
DNP
240
GND
0.1µF
CLKout9*
CLKout9_1_N
SMA
DNP
GND
CLKout8*
C35
CLKout8_1_N
CLKout8_N
R69
DNP
240
C36
CLKout9_P
SMA
0.1µF
R70
DNP
240
R71
DNP
51
GND
B
5
CLKout9
Default: LVDS or LVCMOS, AC coupled
R67
DNP
240
4
0.1µF
CLKout9
CLKout9_1_P
SMA
DNP
R72
51
GND
B
CLKout10
CLKout11
Default: LVPECL, AC coupled
Default: LVPECL, AC coupled
R73
DNP
51
CLKout10
C37
CLKout10_1_P
CLKout10_P
R75
240
C38
SMA
CLKout11_N
0.1µF
R76
240
GND
C
CLKout10_1_N
C40
SMA
CLKout11_P
0.1µF
R78
240
R79
DNP
51
GND
D
CLKout11*
CLKout11_1_N
SMA
DNP
GND
CLKout10*
C39
CLKout10_N
R77
240
0.1µF
R74
51
0.1µF
C
CLKout11
CLKout11_1_P
SMA
DNP
R80
51
GND
Notes:
D
1. Designators greater than and equal to 300 are placed on bottom of PCB
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this
specification or any information contained therein. Texas Instruments and/or its licensors do not
warrant that this design will meet the specifications, will be suitable for your application or fit for
any particular purpose, or will operate in an implementation. Texas Instruments and/or its
licensors do not warrant that the design is production worthy. You should completely validate
and test your design implementation to confirm the system functionality for your application.
1
2
3
4
Designed for: Evaluation Customer
Mod. Date: 11/28/2011
Project: LMK038xx Evaluation Board
Sheet Title: Clock Outputs 3/3
Sheet:8 of 9
Size: B
Schematic: 870600688
Rev: 1.1
Assembly Variant: Customer Eval - 2011-11-22
File: OutClks2.SchDoc
Contact: http://www.national.com/support
5
Figure 20 - LMK03806 Clock Outputs 8 through 11 Schematics
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
http://www.ti.com
© Texas Instruments CopyrightYear
6
31
Bill of Materials
Table 11: Bill of Materials for LMK03806BEVAL Boards
Item
Description
Qty
1
CAP, CERM, 47pF, 50V, +/5%, C0G/NP0, 0603
CAP, CERM, 3900pF, 50V,
+/-10%, X7R, 0603
CAP, CERM, 0.1uF, 25V,
+/-5%, X7R, 0603
1
C1_LF
Kemet
1
C2_LF
MuRata
33
Kemet
1
C5, C8, C12, C15, C17,
C18, C19, C20, C21,
C22, C23, C24, C25,
C26, C27, C28, C29,
C30, C32, C33, C34,
C35, C36, C37, C38,
C39, C40, C41, C42,
C45, C48, C60, C61
C6
AVX
4
C7, C43, C46, C56
Kemet
C0805C106K8PACTU
10
Vishay-Dale
CRCW06030000Z0EA
Vishay-Dale
CRCW0603240RJNEA
Kemet
C0603C104K3RACTU
2
3
4
5
6
CAP, CERM, 22pF, 50V, +/5%, C0G/NP0, 0603
CAP, CERM, 10uF, 10V, +/10%, X5R, 0805
RES, 0 ohm, 5%, 0.1W,
0603
Designator
Manufacturer
PartNumber
C0603C470J5GACTU
GRM188R71H392KA01D
C0603C104J3RACTU
06035A220JAT2A
7
RES, 240 ohm, 5%, 0.1W,
0603
16
8
CAP, CERM, 0.1uF, 25V,
+/-10%, X7R, 0603
CAP, CERM, 1uF, 10V, +/10%, X5R, 0603
CAP, CERM, 4.7uF, 10V,
+/-10%, X5R, 0603
CAP, CERM, 2200pF, 50V,
+/-10%, X7R, 0603
CAP, CERM, 0.1uF, 16V,
+/-10%, X7R, 0603
Connector, SMT, End
launch SMA 50 Ohm
1
C11, C14, R18, R84,
R86, R88, R90, R95,
R100, R104
C13, C16, R27, R28,
R34, R35, R36, R37,
R38, R39, R44, R45,
R75, R76, R77, R78
C31
3
C44, C47, C55
Kemet
C0603C105K8PACTU
1
C53
Kemet
C0603C475K8PACTU
1
C54
Kemet
C0603C222K5RACTU
1
C58
Kemet
C0603C104K4RACTU
16
Emerson
Network
Power
9
10
11
12
13
14
LED 2.8X3.2MM 565NM
RED CLR SMD
3
CLKout0, CLKout0*,
CLKout2, CLKout2*,
CLKout4, CLKout4*,
CLKout6, CLKout6*,
CLKout8, CLKout8*,
CLKout10, CLKout10*,
OSCout0, OSCout0*,
OSCout1, OSCout1*
D1, D2, D4
15
LED 2.8X3.2MM 565NM
GRN CLR SMD
1
D3
16
CONN TERM BLK PCB
5.08MM 2POS OR
RES, 620 ohm, 5%, 0.1W,
0603
1
J1
Lumex
Opto/Compon
ents Inc.
Lumex
Opto/Compon
ents Inc.
Weidmuller
1
R2_LF
Vishay-Dale
17
32
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
142-0701-851
SML-LX2832IC
SML-LX2832GC
1594540000
CRCW0603620RJNEA
November 2013
18
19
20
21
22
23
24
RES, 15k ohm, 5%, 0.1W,
0603
RES, 27k ohm, 5%, 0.1W,
0603
RES, 18 ohm, 5%, 0.1W,
0603
RES, 270 ohm, 5%, 0.1W,
0603
RES, 51 ohm, 5%, 0.1W,
0603
RES, 33 ohm, 5%, 0.1W,
0603
FB, 120 ohm, 500 mA, 0603
4
R3, R5, R7, R9
Vishay-Dale
CRCW060315K0JNEA
4
R4, R6, R8, R10
Vishay-Dale
CRCW060327K0JNEA
2
R12, R23
Vishay-Dale
CRCW060318R0JNEA
6
R14, R15, R19, R20,
R21, R24
R33, R42, R43, R46,
R48, R54, R56, R64,
R66, R72, R74, R80
R57, R60
Vishay-Dale
CRCW0603270RJNEA
Vishay-Dale
CRCW060351R0JNEA
Vishay-Dale
CRCW060333R0JNEA
12
2
1
R81, R85, R87, R89,
R91, R93, R96, R98,
R101
R92
Vishay-Dale
CRCW08050000Z0EA
1
R94
Vishay-Dale
CRCW060351K0JNEA
1
R97
Vishay-Dale
CRCW06032K00FKEA
1
R99
Vishay-Dale
CRCW0603866RFKEA
2
R103
Vishay-Dale
CRCW06031K00FKEA
6
1
S1, S2, S3, S4, S5, S6
U1
SPCS-14
LMK03806BISQ
1
U2
1
uWire
FCI
52601-G10-8LF
34
Micropower 800mA Low
Noise 'Ceramic Stable'
Adjustable Voltage
Regulator for 1V to 5V
Applications
Low Profile Vertical Header
2x5 0.100"
Connector, TH, SMA
VOLTREX
Texas
Instruments
Texas
Instruments
1
Vcc
35
100 MHz TCXO
1
Y3
36
CAP, CERM, 100pF, 50V,
+/-5%, C0G/NP0, 0603
CAP, CERM, 220pF, 50V,
+/-5%, C0G/NP0, 0603
CAP, CERM, 22pF, 50V, +/5%, C0G/NP0, 0603
CAP, CERM, 0.1uF, 25V,
+/-5%, X7R, 0603
CAP, CERM, 470pF, 50V,
+/-10%, X7R, 0603
CAP, CERM, 0.1uF, 25V,
+/-10%, X7R, 0603
CAP, CERM, 1uF, 25V, +/10%, X5R, 0805
0
C1, C2, C3, C4
Emerson
Network
Power
Connor
Winfield
Kemet
C0603C101J5GACTU
0
C2pLF
MuRata
GRM1885C1H221JA01D
0
C9
AVX
0
C10, C62, C64
Kemet
C0603C104J3RACTU
0
C49, C51, C57
Kemet
C0603C471K5RACTU
0
C50, C52, C59
Kemet
C0603C104K3RACTU
0
C63, C65
AVX
25
26
27
28
29
30
31
32
33
37
38
39
40
41
42
RES, 0 ohm, 5%, 0.125W,
0805
RES, 51k ohm, 5%, 0.1W,
0603
RES, 2.00k ohm, 1%, 0.1W,
0603
RES, 866 ohm, 1%, 0.1W,
0603
RES, 1.00k ohm, 1%, 0.1W,
0603
0.875" Standoff
LMK03806
November 2013
9
Murata
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
BLM18AG121SN1D
LP3878SD-ADJ
142-0701-201
CWX813-100.00M
06035A220JAT2A
08053D105KAT2A
SNAU075A
33
43
Connector, SMT, End
launch SMA 50 Ohm
0
44
RES, 270 ohm, 5%, 0.1W,
0603
RES, 0 ohm, 5%, 0.1W,
0603
RES, 100 ohm, 5%, 0.1W,
0603
RES, 51 ohm, 5%, 0.1W,
0603
48
RES, 240 ohm, 5%, 0.1W,
0603
0
49
RES, 1.00k ohm, 1%, 0.1W,
0603
FB, 1000 ohm, 600 mA,
0603
45
46
47
50
51
34
SNAU075A
0
CLKout1, CLKout1*,
CLKout3, CLKout3*,
CLKout5, CLKout5*,
CLKout7, CLKout7*,
CLKout9, CLKout9*,
CLKout11, CLKout11*,
IC_SYNC, OSCin,
OSCin*
R1, R2
Vishay-Dale
CRCW0603270RJNEA
0
R11, R16, R22
Vishay-Dale
CRCW06030000Z0EA
0
R17
Vishay-Dale
CRCW0603100RJNEA
0
Vishay-Dale
CRCW060351R0JNEA
Vishay-Dale
CRCW0603240RJNEA
0
R25, R26, R29, R30,
R31, R32, R40, R41,
R47, R53, R55, R63,
R65, R71, R73, R79,
R300
R49, R50, R51, R52,
R58, R59, R61, R62,
R67, R68, R69, R70
R102
Vishay-Dale
CRCW06031K00FKEA
0
R82, R83
Murata
0
Y1, Y2
ECS
Emerson
Network
Power
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
142-0701-851
BLM18HE102SN1D
DNP_XTAL, ECS-20020-30B-DU
November 2013
15. PCB Layers Stackup
6-layer PCB Stackup includes:
Top Layer for high-priority high-frequency signals (2 oz.)
FR4 Dielectric, 19 mils
RF Ground plane (1 oz.)
FR4, 14.5 mils
Power plane (1 oz.)
FR4, 19 mils
Bottom Layer copper clad for thermal relief (2 oz.)
Top Layer [LMK03806ENG.GTL]
FR4 (Er = 4.8)
19 mil
RF Ground plane [LMK03806ENG.G1]
Power plane #1 [LMK03806ENG.G2]
61.3 mil thick
FR4 (Er = 4.8)
14.5 mil
FR4
19 mil
Bottom Layer [LMK03806ENG.GBL]
Figure 21: PCB Stackup
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
35
16. PCB Layout
Figure 22: Layer 1 - Top
36
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
Figure 23: Layer 2 – RF Ground Plane
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
37
Figure 24: Layer 3 – Vcc Planes
38
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
Figure 25: Layer 4 - Bottom
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
39
Figure 26: Top and Bottom (Composite)
40
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
Appendix A:
EVM Software and Communication: Interfacing uWire
Codeloader is the software used to communicate with the EVM (Please download the latest version from TI.com http://www.ti.com/tool/codeloader). This EVM can be controlled through the uWire interface on board. There are two
options in communicating with the uWire interface from the computer.
OPTION 1
Open Codeloader.exe Click “Select Device” Click “Port Setup” tab Click “LPT” (in Communication Mode)
OPTION 2
November 2013
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
SNAU075A
41
The Adapter Board
This table describes the pins configuration on the adapter board for each EVM board (See examples below table)
Jumper Bank
Code Loader Configuration
EVM
A
B
C
D
E
F
G
H
LMX2581
A4 B1 C2
E5 F1 G1 H1 BUFEN (pin 1), Trigger (pin 7)
LMX2541
A4
C3
E4 F1 G1 H1 CE (pin 1), Trigger (pin 10)
LMK0400x
A0
C3
E5 F1 G1 H1 GOE (pin 7)
LMK01000
A0
C1
E5 F1 G1 H1 GOE (pin 7)
LMK030xx
A0
C1
E5 F1 G1 H1 SYNC (pin 7)
LMK02000
A0
C1
E5 F1 G1 H1 SYNC (pin 7)
LMK0480x
A0 B2 C3
E5 F0 G0 H1 Status_CLKin1 (pin 3)
LMK04816/4906
A0 B2 C3
E5 F0 G0 H1 Status_CLKin1 (pin 3)
LMK01801
A0 B4 C5
E2 F0 G0 H1 Test (pin 3), SYNC0 (pin 10)
LMK0482x (prelease)
A0 B5 C3 D2 E4 F0 G0 H1 CLKin1_SEL (pin 6), Reset (pin 10)
LMX2531
A0
E5 F2 G1 H2 Trigger (pin 1)
LMX2485/7
A0
C1
E5 F2 G1 H0 ENOSC (pin 7), CE (pin 10)
LMK03200
A0
E5 F0 G0 H1 SYNC (pin 7)
LMK03806
A0
C1
E5 F0 G0 H1
LMK04100
A0
C1
E5 F1 G1 H1
Example adapter configuration (LMK01801)
Open Codeloader.exe Click “Select Device” Click “Port Setup” Tab Click “USB” (in Communication Mode)
*Remember to also make modifications in “Pin Configuration” Section according to Table above.
42
SNAU075A
LMK3806 Evaluation Board
Copyright © 2013, Texas Instruments Incorporated
November 2013
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿6丁目24番1号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated