Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
Reference
Design
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
OPA165x SoundPlus™ Low Noise and Distortion, General-Purpose, FET-Input
Audio Operational Amplifiers
1 Features
3 Description
•
The OPA1652 (dual) and OPA1654 (quad) FET-input
operational amplifiers achieve a low 4.5-nV/√Hz noise
density with an ultra-low distortion of 0.00005% at 1
kHz. The OPA1652 and OPA1654 op amps offer railto-rail output swing to within 800 mV with a 2-kΩ
load, which increases headroom and maximizes
dynamic range. These devices also have a high
output drive capability of ±30 mA.
1
•
•
•
•
•
•
•
•
•
•
Low Noise:
4.5 nV/√Hz at 1 kHz
3.8 nV/√Hz at 10 kHz
Low Distortion: 0.00005% at 1 kHz
Low Quiescent Current:
2 mA per Channel
Low Input Bias Current: 10 pA
Slew Rate: 10 V/μs
Wide Gain Bandwidth: 18 MHz (G = 1)
Unity-Gain Stable
Rail-to-Rail Output
Wide Supply Range:
±2.25 V to ±18 V, or 4.5 V to 36 V
Dual and Quad Versions Available
Small Package Sizes:
Dual: SO-8 and MSOP-8
Quad: SO-14 and TSSOP-14
These devices operate over a very-wide-supply range
of ±2.25 V to ±18 V, or 4.5 V to 36 V, on only 2 mA of
supply current per channel. The OPA1652 and
OPA1654 op amps are unity-gain stable and provide
excellent dynamic behavior over a wide range of load
conditions.
These devices also feature completely independent
circuitry for lowest crosstalk and freedom from
interactions between channels, even when overdriven
or overloaded.
The OPA1652 and OPA1654 temperature ranges are
specified from –40°C to +85°C.
2 Applications
•
•
•
•
•
•
SoundPlus™
Analog and Digital Mixers
Audio Effects Processors
Musical Instruments
A/V Receivers
DVD and Blu-Ray™ Players
Car Audio Systems
Device Information(1)
PART NUMBER
OPA1652
OPA1654
PACKAGE
BODY SIZE (NOM)
SOIC (8)
4.90 mm × 3.91 mm
VSSOP (8)
3.00 mm × 3.00 mm
WSON (8)
3.00 mm × 3.00 mm
SOIC (14)
8.65 mm × 3.91 mm
TSSOP (14)
5.00 mm × 4.40 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Input Voltage Noise Spectral Density
9ROWDJH 1RLVH 6SHFWUDO 'HQVLW\ Q9 ¥+]
1000
100
10
1
1
10
100
1k
10k
Frequency (Hz)
100k
1M
10M
C006
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
5
6.1
6.2
6.3
6.4
6.5
6.6
6.7
5
5
5
6
6
7
8
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information: OPA1652 ................................
Thermal Information: OPA1654 ................................
Electrical Characteristics: VS = ±15 V.......................
Typical Characteristics ..............................................
Detailed Description ............................................ 14
7.1
7.2
7.3
7.4
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
14
14
14
17
8
Application and Implementation ........................ 18
8.1 Application Information............................................ 18
8.2 Typical Application .................................................. 21
9 Power Supply Recommendations...................... 24
10 Layout................................................................... 24
10.1 Layout Guidelines ................................................. 24
10.2 Layout Example .................................................... 25
10.3 Power Dissipation ................................................. 25
11 Device and Documentation Support ................. 26
11.1
11.2
11.3
11.4
11.5
11.6
11.7
11.8
Device Support......................................................
Documentation Support ........................................
Related Links ........................................................
Receiving Notification of Documentation Updates
Community Resource............................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
26
27
27
27
27
27
27
28
12 Mechanical, Packaging, and Orderable
Information ........................................................... 28
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (August 2016) to Revision B
Page
•
Added new SON (8) package and body size information to Device Information table .......................................................... 1
•
Added new pinout drawing for OPA1652 DRG (WSON) package ........................................................................................ 3
•
Added thermal information for the DRG (WSON) package in the Thermal Information table................................................ 6
2
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
OPA1652, OPA1654
www.ti.com
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
5 Pin Configuration and Functions
OPA1652 D and DGK Packages
8-Pin SOIC and VSSOP
Top View
OPA1652 DRG Package
8-Pin WSON With Exposed Thermal Pad
Top View
OUT A
1
8
V+
±IN A
2
7
OUT B
+IN A
3
6
±IN B
V±
4
5
+IN B
OUT A
1
±IN A
2
+IN A
3
V±
4
Thermal
Pad
8
V+
7
OUT B
6
±IN B
5
+IN B
Not to scale
Not to scale
Pin Functions: OPA1652
PIN
I/O
DESCRIPTION
NAME
NO.
–IN A
2
I
Inverting input, channel A
+IN A
3
I
Noninverting input, channel A
–IN B
6
I
Inverting input, channel B
+IN B
5
I
Noninverting input, channel B
OUT A
1
O
Output, channel A
OUT B
7
O
Output, channel B
V–
4
—
Negative (lowest) power supply
V+
8
—
Positive (highest) power supply
Thermal pad
—
—
Exposed thermal die pad on underside of DRG package; connect thermal die pad to V–.
Soldering the thermal pad improves heat dissipation and provides specified performance
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
Submit Documentation Feedback
3
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
OPA1654 D and PW Packages
14-Pin SOIC and TSSOP
Top View
OUT A
1
14
OUT D
±IN A
2
13
±IN D
+IN A
3
12
+IN D
V+
4
11
V±
+IN B
5
10
+IN C
±IN B
6
9
±IN C
OUT B
7
8
OUT C
Not to scale
Pin Functions: OPA1654
PIN
I/O
DESCRIPTION
NAME
NO.
–IN A
2
I
Inverting input, channel A
+IN A
3
I
Noninverting input, channel A
–IN B
6
I
Inverting input, channel B
+IN B
5
I
Noninverting input, channel B
–IN C
9
I
Inverting input, channel C
+IN D
10
I
Noninverting input, channel C
–IN D
13
I
Inverting input, channel D
+IN D
12
I
Noninverting input, channel D
OUT A
1
O
Output, channel A
OUT B
7
O
Output, channel B
OUT C
8
O
Output, channel C
OUT D
14
O
Output, channel D
V–
11
—
Negative (lowest) power supply
V+
4
—
Positive (highest) power supply
4
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
OPA1652, OPA1654
www.ti.com
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN
Voltage
Input
V
(V+) + 0.5
V
–10
10
mA
125
°C
200
°C
150
°C
Output short-circuit (2)
Continuous
Operating, TA
Temperature
–55
Junction, TJ
Storage, Tstg
(2)
UNIT
40
(V–) – 0.5
Input (all pins except power-supply pins)
Current
(1)
MAX
Supply voltage, VS = (V+) – (V–)
–65
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Short-circuit to VS / 2 (ground in symmetrical dual supply setups), one amplifier per package.
6.2 ESD Ratings
VALUE
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001
V(ESD)
(1)
(2)
Electrostatic discharge
(1)
UNIT
±2000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±1000
Machine model (MM)
±200
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
Supply voltage
TA
NOM
MAX
UNIT
4.5 (±2.25)
36 (±18)
V
–40
85
°C
Operating temperature
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
Submit Documentation Feedback
5
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
6.4 Thermal Information: OPA1652
OPA1652
THERMAL METRIC
(1)
D (SOIC)
DGK
(VSSOP)
DRG (WSON)
8 PINS
8 PINS
8 PINS
UNIT
RθJA
Junction-to-ambient thermal resistance
143.6
218.9
66.9
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
76.9
78.6
54.5
°C/W
RθJB
Junction-to-board thermal resistance
61.8
103.7
40.4
°C/W
ψJT
Junction-to-top characterization parameter
27.8
14.6
1.9
°C/W
ψJB
Junction-to-board characterization parameter
61.3
101.8
40.4
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
N/A
10.8
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Thermal Information: OPA1654
OPA1654
THERMAL METRIC (1)
D (SOIC)
PW (TSSOP)
14 PINS
14 PINS
UNIT
RθJA
Junction-to-ambient thermal resistance
90.1
126.9
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
54.8
46.6
°C/W
RθJB
Junction-to-board thermal resistance
44.4
58.6
°C/W
ψJT
Junction-to-top characterization parameter
19.9
5.5
°C/W
ψJB
Junction-to-board characterization parameter
44.2
57.8
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
N/A
°C/W
(1)
6
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
OPA1652, OPA1654
www.ti.com
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
6.6 Electrical Characteristics: VS = ±15 V
at TA = 25°C, RL = 2 kΩ, and VCM = VOUT = midsupply, unless otherwise noted
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
AUDIO PERFORMANCE
THD + N
IMD
Total harmonic distortion + noise
Intermodulation distortion
0.00005%
G = 1, f = 1 kHz, VO = 3 VRMS
G = 1,
VO = 3 VRMS
–126
SMPTE and DIN Two-Tone, 4:1
(60 Hz and 7 kHz)
0.00005%
DIM 30 (3-kHz square wave
and 15-kHz sine wave)
0.00005%
CCIF Twin-Tone
(19 kHz and 20 kHz)
0.00005%
dB
–126
dB
–126
dB
–126
dB
FREQUENCY RESPONSE
GBW
Gain-bandwidth product
G=1
18
SR
Slew rate
G = –1
10
MHz
V/µs
Full power bandwidth (1)
VO = 1 VP
1.6
MHz
Overload recovery time
G = –10
Channel separation (dual and quad)
f = 1 kHz
Input voltage noise
f = 20 Hz to 20 kHz
4.0
µVPP
f = 1 kHz
4.5
nV/√Hz
f = 10 kHz
3.8
nV/√Hz
3
fA/√Hz
1
µs
–120
dB
NOISE
en
Input voltage noise density
In
Input current noise density
f = 1 kHz
OFFSET VOLTAGE
VOS
Input offset voltage
PSRR
Power-supply rejection ratio
VS = ±2.25 V to ±18 V
±0.5
±1.5
VS = ±2.25 V to ±18 V, TA = –40°C to 85°C (2)
2
8
µV/°C
mV
VS = ±2..25 V to ±18 V
3
8
µV/V
INPUT BIAS CURRENT
IB
Input bias current
VCM = 0 V
±10
±100
pA
IOS
Input offset current
VCM = 0 V
±10
±100
pA
INPUT VOLTAGE RANGE
VCM
Common-mode voltage range
(V–) + 0.5
CMRR
Common-mode rejection ratio
100
(V+) – 2
V
110
dB
INPUT IMPEDANCE
Differential
Common-mode
100 || 6
MΩ || pF
6000 || 2
GΩ || pF
OPEN-LOOP GAIN
Open-loop voltage gain
(V–) + 0.8 V ≤ VO ≤ (V+) – 0.8 V, RL = 2 kΩ
VOUT
Voltage output
RL = 2 kΩ
IOUT
Output current
ZO
Open-loop output impedance
ISC
Short-circuit current (3)
±50
mA
CLOAD
Capacitive load drive
100
pF
AOL
106
114
dB
OUTPUT
(V–) + 0.8
(V+) – 0.8
See Typical Characteristics
f = 1 MHz
V
mA
See Typical Characteristics
Ω
POWER SUPPLY
VS
IQ
Specified voltage
Quiescent current
(per channel)
±2.25
IOUT = 0 A
2
IOUT = 0 A, TA = –40°C to 85°C (2)
±18
V
2.5
mA
2.8
mA
TEMPERATURE
(1)
(2)
(3)
Specified range
–40
85
°C
Operating range
–55
125
°C
Full-power bandwidth = SR / (2π × VP), where SR = slew rate.
Specified by design and characterization.
One channel at a time.
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
Submit Documentation Feedback
7
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
6.7 Typical Characteristics
at TA = 25°C, VS = ±15 V, and RL = 2 kΩ, unless otherwise noted.
Voltage Noise (500 nV/div)
9ROWDJH 1RLVH 6SHFWUDO 'HQVLW\ Q9 ¥+]
1000
100
10
1
1
10
100
1k
10k
100k
1M
10M
Frequency (Hz)
Time (1 s/div)
C006
Figure 2. 0.1-Hz to 10-Hz Noise
Figure 1. Input Voltage Noise Density vs Frequency
20
10k
E2o = e2n + (inRS)2 + 4KTRS
18
RS
Output Voltage (V)
Voltage Noise (nV/ Hz)
EO
1k
G002
OPA166x
100
OPA165x
10
VS = ± 15 V
15
12
10
8
5
VS = ± 2.25 V
2
Resistor Noise
1
100
1k
10k
100k
0
10k
1M
Source Resistance (W)
Gain
Phase
120
Gain = −1 V/V
Gain = +1 V/V
Gain = +10 V/V
90
60
40
0
45
20
20
Gain (dB)
80
Phase (°)
135
100
G004
40
180
140
10M
Figure 4. Maximum Output Voltage vs Frequency
Figure 3. Voltage Noise vs Source Resistance
Gain (dB)
100k
1M
Frequency (Hz)
G003
0
CL = 10 pF
−20
10
100
1k
10k
100k
Frequency (Hz)
1M
10M
0
100M
G005
CL = 10 pF
−20
100k
1M
10M
Frequency (Hz)
Figure 5. Gain and Phase vs Frequency
8
Submit Documentation Feedback
100M
G006
Figure 6. Closed-Loop Gain vs Frequency
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
OPA1652, OPA1654
www.ti.com
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
Typical Characteristics (continued)
at TA = 25°C, VS = ±15 V, and RL = 2 kΩ, unless otherwise noted.
0.01
G = 10 V/V, RL = 600 Ω
G = 10 V/V, RL = 2 kΩ
G = +1 V/V, RL = 600 Ω
G = +1 V/V, RL = 2 kΩ
G = −1 V/V, RL = 600 Ω
G = −1 V/V, RL = 2 kΩ
0.001
VOUT = 3 VRMS
BW = 80 kHz
-15V
0.0001
0.00001
0.001
20
100
1k
Frequency (Hz)
10k
0.00001
20k
20
G = 10 V/V, RL = 600 Ω
G = 10 V/V, RL = 2 kΩ
G = +1 V/V, RL = 600 Ω
G = +1 V/V, RL = 2 kΩ
G = −1 V/V, RL = 600 Ω
G = −1 V/V, RL = 2 kΩ
0.001
100
1k
Frequency (Hz)
10k
20k
G008
Figure 8. THD+N Ratio vs Frequency
0.01
VOUT = 3 VRMS
BW = 500 kHz
VOUT = 3 VRMS
BW = 500 kHz
+15V
RS = 0 W
RS = 30 W
RS = 60 W
RS = 1 kW
RSOURCE OPA1652
-15V
THD+N (%)
THD+N (%)
RL
G007
Figure 7. THD+N Ratio vs Frequency
0.0001
0.001
RL
0.0001
20
100
1k
Frequency (Hz)
10k
0.00001
100k
20
100
G009
Figure 9. THD+N Ratio vs Frequency
1k
Frequency (Hz)
10k
100k
G010
Figure 10. THD+N Ratio vs Frequency
0.01
0.01
DIM 30: 3 kHz − Square Wave, 15 kHz Sine Wave
CCIF Twin Tone: 19 kHz and 20 kHz
SMPTE / DIN: Two −Tone 4:1, 60 Hz and 7 KHz
f = 1 kHz
BW = 80 kHz
RS = 0 Ω
0.001
THD+N (%)
THD+N (%)
RS = 0 W
RS = 30 W
RS = 60 W
RS = 1 kW
0.0001
0.01
0.00001
VOUT = 3 VRMS
BW = 80 kHz
+15V
RSOURCE OPA1652
THD+N (%)
THD+N (%)
0.01
G = 10 V/V, RL = 600 Ω
G = 10 V/V, RL = 2 kΩ
G = +1 V/V, RL = 600 Ω
G = +1 V/V, RL = 2 kΩ
G = −1 V/V, RL = 600 Ω
G = −1 V/V, RL = 2 kΩ
0.0001
0.00001
1m
10m
0.001
0.0001
100m
1
Output Amplitude (Vrms)
10 20
Figure 11. THD+N Ratio vs Output Amplitude
G = +1 V/V
0.00001
100m
G011
1
Output Amplitude (Vrms)
10
20
G012
Figure 12. Intermodulation Distortion vs Output Amplitude
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
Submit Documentation Feedback
9
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
Typical Characteristics (continued)
at TA = 25°C, VS = ±15 V, and RL = 2 kΩ, unless otherwise noted.
140
−80
VOUT = 3 VRMS
Gain = +1 V/V
120
CMRR, PSRR (dB)
Crosstalk (dB)
−100
−120
−140
100
80
60
40
20
−160
100
1k
10k
0
100
100k
Frequency (Hz)
10k
100k
1M
Frequency (Hz)
10M
100M
G014
Figure 14. CMRR and PSRR vs Frequency
(Referred to Input)
VIN
VOUT
Voltage (25 mV/div)
Voltage (25 mV/div)
VIN
VOUT
G = −1 V/V
CL = 100 pF
G = +1 V/V
CL = 100 pF
Time (0.2 ms/div)
Time (0.2 ms/div)
G015
Figure 15. Small-Signal Step Response (100 mV)
VIN
VOUT
G = −1 V/V
CL = 100 pF
Voltage (2.5 V/div)
G = + 1V/V
RF = 2 kW
CL = 100 pF
Time (1 ms/div)
Time (1 ms/div)
G017
Figure 17. Large-Signal Step Response
Submit Documentation Feedback
G016
Figure 16. Small-Signal Step Response (100 mV)
VIN
VOUT
Voltage (2.5 V/div)
1k
G013
Figure 13. Channel Separation vs Frequency
10
+PSRR
−PSRR
CMRR
G018
Figure 18. Large-Signal Step Response
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
OPA1652, OPA1654
www.ti.com
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
Typical Characteristics (continued)
at TA = 25°C, VS = ±15 V, and RL = 2 kΩ, unless otherwise noted.
50
40
RS
OPA1652
30
VOUT = 100 mVPP
G = +1 V/V
20
RL
-15 V
CL
10
5
150
200
250
Capacitance (pF)
300
350
VOUT = 100 mVPP
G = −1 V/V
20
5
100
CL
-15 V
25
15
50
OPA1652
30
10
0
RS
35
15
0
RS = 0 W
RS = 25 W
RS = 50 W
RF = 2 kW
+15 V
40
+15 V
35
25
RI = 2 kW
45
Overshoot (%)
Overshoot (%)
50
RS = 0 W
RS = 25 W
RS = 50 W
45
0
400
0
50
100
150
200
250
Capacitance (pF)
G019
Figure 19. Small-Signal Overshoot vs Capacitive Load
300
350
400
G020
Figure 20. Small-Signal Overshoot vs Capacitive Load
4
25
VOUT = 100 mVPP
G = −1 V/V
RS = 0 W
20
CF
RI = 2 kW
RF = 2 kW
3
RS
OPA1652
15
AOL (µV)
Overshoot (%)
+15 V
CL
-15 V
10
2
1
0
5
RL = 2 kΩ
0
0
1
2
3
Capacitance (pF)
4
−1
−40
5
G021
1200
85
110
135
G022
Ibp
Ibn
Ios
6
0
−400
−800
−1200
−1600
−2000
−40
35
60
Temperature (°C)
8
Ibn
Ibp
Ios
Ib and Ios Current (pA)
Ib and Ios Current (pA)
400
10
Figure 22. Open-Loop Gain vs Temperature
Figure 21. Small-Signal Overshoot vs Feedback Capacitor
(100-mV Output Step)
800
−15
4
2
0
−2
−4
−6
−15
10
35
60
Temperature (°C)
85
110
135
G023
Figure 23. IB and IOS vs Temperature
−8
−18 −15 −12 −9 −6 −3 0
3
6
9
Common − Mode Voltage (V)
12
15
18
G024
Figure 24. IB and IOS vs Common-Mode Voltage
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
Submit Documentation Feedback
11
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
Typical Characteristics (continued)
3
3
2.5
2.5
Supply Current (mA)
Supply Current (mA)
at TA = 25°C, VS = ±15 V, and RL = 2 kΩ, unless otherwise noted.
2
1.5
1
2
1.5
1
0.5
0.5
0
−40
−15
10
35
60
Temperature (°C)
85
110
0
135
30
80
8
12
16
20
24
Supply Voltage (V)
0
−40 C
−25 C
0C
25 C
85 C
125 C
−10
−20
−30
36
G026
+Isc
−Isc
0
5
10
15
20 25 30 35 40
Output Current (mA)
45
50
55
20
0
−20
−40
−60
−80
60
−100
−40
−15
10
G029
Figure 27. Output Voltage vs Output Current
35
60
Temperature (°C)
85
110
135
G028
Figure 28. Short-Circuit Current vs Temperature
90
50
G = +1 V/V
80
G = +1 V/V
VIN = 100 mVPP
40
70
Overshoot (%)
60
50
40
30
20
30
20
10
VS = ± 2.25 V
VS = ± 18 V
10
0
50
100
150
200
250
Capacitance (pF)
300
350
Submit Documentation Feedback
400
0
0
50
G031
Figure 29. Phase Margin vs Capacitive Load
12
32
40
10
0
28
60
20
Phase Margin (°)
4
Figure 26. Supply Current vs Supply Voltage
100
Isc (mA)
Output Volage Swing (V)
Figure 25. Supply Current vs Temperature
40
−40
0
G025
100
150
200
250
Capacitance (pF)
300
350
400
G032
Figure 30. Percent Overshoot vs Capacitive Load
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
OPA1652, OPA1654
www.ti.com
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
Typical Characteristics (continued)
at TA = 25°C, VS = ±15 V, and RL = 2 kΩ, unless otherwise noted.
20 kW
VIN
VOUT
2 kW
20 kW
+18 V
2 kW
+18 V
VOUT
OPA1652
Output Voltage (5 V/div)
Output Voltage (5 V/div)
G = −10 V/V
VIN
-18 V
G = -10
VIN
VOUT
VOUT
OPA1652
VIN
-18 V
G = −10 V/V
G = -10
Time (0.4 ms/div)
Time (0.4 ms/div)
G033
Figure 31. Negative Overload Recovery
Figure 32. Positive Overload Recovery
1k
20
+18 V
15
Voltage (V)
10
Impedance (Ω)
G027
100
5
G = +1 V/V
OPA1652
-18 V
37VPP
Sine Wave
(±18.5 V)
0
−5
−10
VIN
VOUT
−15
10
10
100
1k
10k
100k
Frequency (Hz)
1M
10M
100M
−20
G030
Figure 33. Open-Loop Output Impedance vs Frequency
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
Time (125 ms/div)
G034
Figure 34. No Phase Reversal
Submit Documentation Feedback
13
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
7 Detailed Description
7.1 Overview
The OPA1652 and OPA1654 are unity-gain stable, precision dual and quad op amps with very low noise. The
Functional Block Diagram shows a simplified schematic of the OPA165x (with one channel shown). The device
consists of a very low noise input stage with a folded cascode and a rail-to-rail output stage. This topology
exhibits superior noise and distortion performance across a wide range of supply voltages not previously
delivered by audio operational amplifiers.
7.2 Functional Block Diagram
V+
Tail
Current
VBIAS1
VIN+
Class AB
Control
Circuitry
VO
VINVBIAS2
VCopyright © 2016, Texas Instruments Incorporated
7.3 Feature Description
7.3.1 Phase Reversal Protection
The OPA165x family has internal phase-reversal protection. Many op amps exhibit phase reversal when the
input is driven beyond the linear common-mode range. This condition is most often encountered in noninverting
circuits when the input is driven beyond the specified common-mode voltage range, causing the output to
reverse into the opposite rail. The input of the OPA165x prevents phase reversal with excessive common-mode
voltage. Instead, the appropriate rail limits the output voltage. This performance is shown in Figure 35.
20
+18 V
15
Voltage (V)
10
5
G = +1 V/V
OPA1652
-18 V
37VPP
Sine Wave
(±18.5 V)
0
−5
−10
VIN
VOUT
−15
−20
Time (125 ms/div)
G034
Figure 35. Output Waveform Devoid of Phase Reversal During an Input Overdrive Condition
14
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
OPA1652, OPA1654
www.ti.com
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
Feature Description (continued)
7.3.2 Input Protection
The input terminals of the OPA1652 and OPA1654 are protected from excessive differential voltage with back-toback diodes, as Figure 36 illustrates. In most circuit applications, the input protection circuitry has no
consequence. However, in low-gain or G = 1 circuits, fast ramping input signals can forward bias these diodes
because the output of the amplifier cannot respond rapidly enough to the input ramp. If the input signal is fast
enough to create this forward bias condition, the input signal current must be limited to 10 mA or less. If the input
signal current is not inherently limited, an input series resistor (RI) or a feedback resistor (RF) can limit the signal
input current. This resistor degrades the low-noise performance of the OPA165x, and is examined in the Noise
Performance section. Figure 36 shows an example configuration when both current-limiting input and feedback
resistors are used.
RF
-
OPA165x
RI
Input
Output
+
Copyright © 2016, Texas Instruments Incorporated
Figure 36. Pulsed Operation
7.3.3 Electrical Overstress
Designers typically ask questions about the capability of an operational amplifier to withstand electrical
overstress. These questions tend to focus on the device inputs, but can involve the supply voltage pins or the
output pin. Each of these different pin functions have electrical stress limits determined by the voltage breakdown
characteristics of the particular semiconductor fabrication process and specific circuits connected to the pin.
Additionally, internal electrostatic discharge (ESD) protection is built into these circuits to protect them from
accidental ESD events both before and during product assembly.
A good understanding of this basic ESD circuitry and the relevance to an electrical overstress event is helpful.
Figure 37 illustrates the ESD circuits contained in the OPA165x (indicated by the dashed line area). The ESD
protection circuitry involves several current-steering diodes connected from the input and output pins and routed
back to the internal power-supply lines, where the diodes meet at an absorption device internal to the operational
amplifier. This protection circuitry is intended to remain inactive during normal circuit operation.
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
Submit Documentation Feedback
15
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
Feature Description (continued)
TVS
+
±
RF
+VS
R1
IN±
250 Ÿ
RS
IN+
250 Ÿ
+
Power-Supply
ESD Cell
ID
VIN
RL
+
±
+
±
±VS
TVS
Copyright © 2016, Texas Instruments Incorporated
Figure 37. Equivalent Internal ESD Circuitry Relative to a Typical Circuit Application
An ESD event produces a short-duration, high-voltage pulse that is transformed into a short-duration, highcurrent pulse when discharging through a semiconductor device. The ESD protection circuits are designed to
provide a current path around the operational amplifier core to prevent damage. The energy absorbed by the
protection circuitry is then dissipated as heat.
When an ESD voltage develops across two or more amplifier device pins, current flows through one or more
steering diodes. The absorption device activates depending on the path that the current takes. The absorption
device has a trigger, or threshold voltage, that is above the normal operating voltage of the OPA165x, but below
the device breakdown voltage level. When this threshold is exceeded, the absorption device quickly activates
and clamps the voltage across the supply rails to a safe level.
When the operational amplifier connects into a circuit (refer to Figure 37), the ESD protection components are
intended to remain inactive and do not become involved in the application circuit operation. However,
circumstances may arise where an applied voltage exceeds the operating voltage range of a given pin. If this
condition occurs, there is a risk that some internal ESD protection circuits can turn on and conduct current. Any
such current flow occurs through steering-diode paths and rarely involves the absorption device.
Figure 37 shows a specific example where the input voltage (VIN) exceeds the positive supply voltage (V+) by
500 mV or more. Much of what happens in the circuit depends on the supply characteristics. If V+ can sink the
current, one of the upper input steering diodes conducts and directs current to V+. Excessively high current
levels can flow with increasingly higher VIN. As a result, the data sheet specifications recommend that
applications limit the input current to 10 mA.
If the supply is not capable of sinking the current, VIN begins sourcing current to the operational amplifier, and
then becomes the source of positive supply voltage. The danger in this case is that the voltage can rise to levels
that exceed the absolute maximum ratings of the operational amplifier.
16
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
OPA1652, OPA1654
www.ti.com
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
Feature Description (continued)
Another common question explains what happens to the amplifier if an input signal is applied to the input when
the power supplies (V+ or V–) are at 0 V. This depends on the supply characteristic when at 0 V, or at a level
below the input signal amplitude. If the supplies appear as high impedance, then the input source supplies the
operational amplifier current through the current-steering diodes. This state is not a normal bias condition; most
likely, the amplifier does not operate normally. If the supplies are at low impedance, then the current through the
steering diodes can become quite high. The current level depends on the ability of the input source to deliver
current, and any resistance in the input path.
If there is any uncertainty about the ability of the supply to absorb this current, add external Zener diodes to the
supply pins; see Figure 37. Select the Zener voltage so the diode does not turn on during normal operation.
However, the Zener voltage must be low enough so that the Zener diode conducts if the supply pin rises above
the safe-operating, supply-voltage level.
7.4 Device Functional Modes
7.4.1 Operating Voltage
The OPA165x series op amps operate from ±2.25 V to ±18 V supplies while maintaining excellent performance.
The OPA165x series can operate with as little as 4.5 V between the supplies and with up to 36 V between the
supplies. However, some applications do not require equal positive and negative output voltage swing. With the
OPA165x series, power-supply voltages do not need to be equal. For example, the positive supply can be set to
25 V with the negative supply at –5 V.
In all cases, the common-mode voltage must be maintained within the specified range. In addition, key
parameters are assured over the specified temperature range of TA = –40°C to +85°C. Parameters that vary
significantly with operating voltage or temperature are shown in the Typical Characteristics section.
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
Submit Documentation Feedback
17
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
8.1.1 Noise Performance
Figure 38 shows the total circuit noise for varying source impedances with the op amp in a unity-gain
configuration (no feedback resistor network, and therefore no additional noise contributions).
The OPA165x ( Gain bandwidth = 18 MHz, G = 1) is shown with total circuit noise calculated. The op amp
contributes a voltage noise component and a current noise component. The voltage noise is commonly modeled
as a time-varying component of the offset voltage. The current noise is modeled as the time-varying component
of the input bias current, and reacts with the source resistance to create a voltage component of noise.
Therefore, the lowest noise op amp for a given application depends on the source impedance. For low source
impedance, current noise is negligible, and voltage noise typically dominates the total noise of the circuit. The
voltage noise of the OPA165x series op amps makes the series a suitable choice for source impedances greater
than or equal to 1-kΩ.
The equation in Figure 38 shows the calculation of the total circuit noise, with these parameters:
• en = Voltage noise
• in = Current noise
• RS = Source impedance
• k = Boltzmann’s constant = 1.38 × 10–23 J/K
• T = Temperature in Kelvins (K)
10k
Voltage Noise (nV/ Hz )
E2o = e2n + (inRS)2 + 4KTRS
1k
OPA166X
100
OPA165X
10
Resistor Noise
1
100
1k
10k
100k
1M
Source Resistance (Ω)
G003
Figure 38. Noise Performance of the OPA165x in Unity-Gain Buffer Configuration
Design of low-noise op amp circuits requires careful consideration of a variety of possible noise contributors:
noise from the signal source, noise generated in the op amp, and noise from the feedback network resistors. The
total noise of the circuit is the root-sum-square combination of all noise components.
The resistive portion of the source impedance produces thermal noise proportional to the square root of the
resistance. Figure 38 plots this equation. The source impedance is typically fixed; consequently, select the op
amp and the feedback resistors to minimize the respective contributions to the total noise.
18
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
OPA1652, OPA1654
www.ti.com
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
Application Information (continued)
Figure 39 illustrates both inverting (Figure 39 B) and noninverting (Figure 39 A) op amp circuit configurations with
gain. In circuit configurations with gain, the feedback network resistors contribute noise. The current noise of the
op amp reacts with the feedback resistors, creating additional noise components. The feedback resistor values
can generally be selected to make these noise sources negligible. The equations for total noise are shown for
both configurations.
Noise at the output:
A) Noise in Noninverting Gain Configuration
R2
2
2
O
E
R1
R2
= 1+
R1
2
2
en +
R2
2
2
R1
2
e1 + e2 + 1 +
R2
R1
es2
EO
RS
Where eS =
4kTRS = thermal noise of RS
e1 =
4kTR1 = thermal noise of R1
e2 =
4kTR2 = thermal noise of R2
VS
Noise at the output:
B) Noise in Inverting Gain Configuration
R2
2
R2
2
EO = 1 +
R1
RS
R 1 + RS
en2 +
2
R2
R1 + RS
e12 + e22 +
2
R2
R1 + RS
es2
EO
VS
Where eS =
4kTRS = thermal noise of RS
e1 =
4kTR1 = thermal noise of R1
e2 =
4kTR2 = thermal noise of R2
Copyright © 2016, Texas Instruments Incorporated
Note:
For the OPA165x series of op amps at 1 kHz, en = 4.5 nV/√Hz.
Figure 39. Noise Calculation in Gain Configurations
8.1.2 Total Harmonic Distortion Measurements
The OPA165x series op amps have excellent distortion characteristics. THD + noise is below 0.0002% (G = 1,
VO = 3 VRMS, bandwidth = 80 kHz) throughout the audio frequency range, 20 Hz to 20 kHz, with a 2-kΩ load (see
Figure 7 for characteristic performance).
The distortion produced by the OPA165x series op amps is below the measurement limit of many commercially
available distortion analyzers. However, a special test circuit (such as Figure 40 shows) can extend the
measurement capabilities.
Op amp distortion can be considered an internal error source that refers to the input. Figure 40 shows a circuit
that causes the op amp distortion to be gained up (refer to the table in Figure 40 for the distortion gain factor for
various signal gains). The addition of R3 to the otherwise standard noninverting amplifier, configuration alters the
feedback factor or noise gain of the circuit. The closed-loop gain is unchanged, but the distortion gain factor
reduces the feedback available for error connection, that extends the resolution by the same amount. Note that
the input signal and load applied to the op amp are the same as with conventional feedback without R3. The
value of R3 must be kept small to minimize the effect on the distortion measurements.
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
Submit Documentation Feedback
19
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
Application Information (continued)
The validity of this technique can be verified by duplicating measurements at high gain or high frequency where
the distortion is within the measurement capability of the test equipment. The Audio Precision System Two
distortion and noise analyzer calculated the measurements for this data sheet, which significantly simplifies
repetitive measurements. Manual distortion measurement instruments performs this measurement technique.
R1
R2
SIGNAL DISTORTION
GAIN
GAIN
R3
OPA165x
VO = 3 VRMS
R
Signal Gain = 1+ 2
R1
Distortion Gain = 1+
R2
R1 II R3
Generator
Output
R1
R2
R3
¥
1 kW
10 W
+1
101
-1
101
4.99 kW 4.99 kW 49.9 W
+10
110
549 W 4.99 kW 49.9 W
Analyzer
Input
Audio Precision
System Two(1)
with PC Controller
Load
Copyright © 2016, Texas Instruments Incorporated
(1) For measurement bandwidth, see Figure 7 through Figure 12.
Figure 40. Distortion Test Circuit
8.1.3 Capacitive Loads
The dynamic characteristics of the OPA1652 and OPA1654 are optimized for commonly encountered gains,
loads, and operating conditions. The combination of low closed-loop gain and high capacitive loads decreases
the phase margin of the amplifier and can lead to gain peaking or oscillations. As a result, heavier capacitive
loads must be isolated from the output. The simplest way to achieve this isolation is to add a small resistor (RS
equal to 50 Ω, for example) in series with the output.
This small series resistor also prevents excess power dissipation if the output of the device becomes shorted.
Figure 19 illustrates a graph of Small-Signal Overshoot vs Capacitive Load for several values of RS. For more
details about analysis techniques and application circuits, see Feedback Plots Define Op Amp AC Performance
(SBOA015), available for download from the TI website (www.ti.com).
20
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
OPA1652, OPA1654
www.ti.com
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
8.2 Typical Application
The low noise and distortion of the OPA165x family of audio operational amplifiers make them an excellent
choice for a number of analog audio circuits. Figure 41 illustrates a power amplifier circuit suitable for high-fidelity
headphone applications.
+12 V
100 F
0.1 F
CBULK
0.1 F
CBYP
CBYP
+
Input
RIN
±
100 k
OPA1652
BUF634
Output
0.1 F
RBW
0.1 F
CBYP
100 F
CBYP
CBULK
-12V
R1
R2
200
200
Copyright © 2016, Texas Instruments Incorporated
Figure 41. Composite Power Amplifier for Headphones
8.2.1 Design Requirements
•
•
•
•
Gain: 6 dB
Output Voltage: > 2 VRMS, 32-Ω Load
Output Impedance: < 1 Ω
THD+N: < –110dB (1 kHz, 2 VRMS, 32-Ω Load)
8.2.2 Detailed Design Procedure
The power amplifier circuit (single channel shown) features a BUF634 high-speed buffer amplifier inside the
feedback loop of an OPA1652 to increase the amount of available output current. The bandwidth and power
consumption of the BUF634 can be set with an external resistor (RBW). For this circuit, RBW uses a 0-Ω resistor
that configures the BUF634 for the widest bandwidth and highest performance. Feedback resistors R1 and R2 (as
shown in Equation 1) calculate the gain of the circuit:
R2
AV 1
R1
(1)
To achieve the design goal of a 6-dB voltage gain (2 V/V), R1 and R2 must have equal values. These resistors
also contribute noise thermal noise to the circuit. The voltage noise spectral density of the feedback resistors,
referred to the amplifier input, is given in Equation 2:
eNR
4kT R2 || R1
(2)
Ideally, the thermal noise contributions of the resistors do not significantly degrade the noise performance of the
circuit. Selecting resistor values so the resistor noise is less than one-third the input voltage noise of the op amp
(Equation 3) ensures that any increase in the circuit noise as a result of the feedback resistor contributions is
minimal.
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
Submit Documentation Feedback
21
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
Typical Application (continued)
eNR d
eOA
3
(3)
To calculate the required resistor values, Equation 3 is inserted into Equation 2, and the resulting equation is
rearranged to solve for the parallel combination of R1 and R2 , as shown in Equation 4. Using a value of 3.8
nV/√Hz as the broadband voltage noise of the OPA1652 results in a value of 96.8 Ω for the parallel combination
of R1 and R2. R1 and R2 use standard value 200-Ω resistors, resulting in a parallel value of 100 Ω, which is
suitably close to the required value.
2
3.8 nV/ Hz
e 2
R1||R2 d OA d
d 96.8
36kT 36×1.381×10-23 ×300
(4)
Because of the extremely wide bandwidth and high slew rate of the BUF634, no additional components are
required to maintain stability in the circuit or prevent latch-up conditions. This circuit is stable with capacitive
loads over 1-nF, which is suitable for headphone applications.
8.2.3 Application Curves
Total Harmonic Distortion + Noise (dB)
6.2
6.15
Gain (dB)
6.1
6.05
6
5.95
5.9
No Load
5.85
32-
5.8
10
100
1k
Load
10k
Frequency (Hz)
0.1
±60
±70
0.01
±80
±90
0.001
±100
±110
±120
±130
±140
0.001
16-
Load
32-
Load
128-
Load
250-
Load
0.01
0.0001
0.00001
0.1
1
10
Output Voltage (VRMS)
C005
Total Harmonic Distortion + Noise (%)
The measured performance of the circuit is shown in Figure 42 through Figure 46. The frequency response is
extremely flat over the full audio bandwidth, deviating only 0.004 dB over the audible range. The decrease in
gain shown at low frequency is a result of the test equipment, and not the amplifier circuit. The amplifier output
impedance, calculated from the change in gain in the loaded and unloaded conditions, is 0.036 Ω. The maximum
output power (before clipping) is displayed in Figure 43. For a 32-Ω load, the power amplifier delivered 781 mW
before clipping. The best THD+N performance achieved with a 32-Ω load was –117.2 dB at 678 mW (1 kHz, 22kHz measurement bandwidth). THD+N vs frequency is shown in Figure 44 for a 2-VRMS output level measured in
a 90-kHz bandwidth. The worst-case measurement was for a 16-Ω load (250 mW), 20-kHz input frequency,
–91.8 dB (0.0026%). The amplifier output spectrum for a 2-VRMS, 1 kHz, fundamental into two different loads is
shown in Figure 45 and Figure 46. All distortion harmonics are below –120 dB relative to the fundamental for
both loading conditions.
C007
22-kHz measurement bandwidth, 1-kHz output
Figure 42. Amplifier Transfer Function
22
Submit Documentation Feedback
Figure 43. THD+N vs Frequency for Various Loads
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
OPA1652, OPA1654
www.ti.com
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
±70
±80
16-
Load
32-
Load
128-
Load
250-
Load
0
0.1
0.01
±90
0.001
±100
±110
±20
±40
Amplitude (dBc)
±60
Total Harmonic Distortion + Noise (%)
Total Harmonic Distortion + Noise (dB)
Typical Application (continued)
10
100
1k
Frequency (Hz)
±80
±100
±120
±140
±160
0.0001
±120
±60
±180
10k
0
5k
10k
15k
Frequency (Hz)
C002
90-kHz measurement bandwidth, 2-VRMS output
20k
C003
1 kHz, 32-Ω load, 2-VRMS output
Figure 44. THD+N vs Frequency for Various Loads
Figure 45. Output Spectrum
0
±20
Amplitude (dBc)
±40
±60
±80
±100
±120
±140
±160
±180
0
5k
10k
15k
Frequency (Hz)
20k
C004
1 kHz, 250-Ω load, 2 VRMS
Figure 46. Output Spectrum
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
Submit Documentation Feedback
23
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
9 Power Supply Recommendations
The OPA165x series is specified for operation from 4.5 V to 36 V (±2.25 V to ±18 V); many specifications apply
from –40°C to +85°C. Parameters that can exhibit significant variance with regard to operating voltage or
temperature are presented in the Typical Characteristics section. Applications with noisy or high-impedance
power supplies require decoupling capacitors close to the device pins. In most cases, 0.1-µF capacitors are
adequate.
10 Layout
10.1 Layout Guidelines
For best operational performance of the device, use good printed-circuit board (PCB) layout practices, including:
• Noise can propagate into analog circuitry through the power pins of the circuit as a whole and of op amp
itself. Bypass capacitors are used to reduce the coupled noise by providing low-impedance power sources
local to the analog circuitry.
– Connect low-ESR, 0.1-µF ceramic bypass capacitors between each supply pin and ground, placed as
close to the device as possible. A single bypass capacitor from V+ to ground is applicable for singlesupply applications.
• Separate grounding for analog and digital portions of circuitry is one of the simplest and most-effective
methods of noise suppression. One or more layers on multilayer PCBs are typically devoted to ground
planes. A ground plane helps distribute heat and reduces electromagnetic interference (EMI) noise pickup.
Physically separate digital and analog grounds, observing the flow of the ground current.
• To reduce parasitic coupling, run the input traces as far away from the supply or output traces as possible. If
these traces cannot be kept separate, crossing the sensitive trace perpendicular is much better as opposed to
in parallel with the noisy trace.
• Place the external components as close to the device as possible. As illustrated in Figure 47, keeping RF and
RG close to the inverting input minimizes parasitic capacitance.
• Keep the length of input traces as short as possible. Always remember that the input traces are the most
sensitive part of the circuit.
• Consider a driven, low-impedance guard ring around the critical traces. A guard ring can significantly reduce
leakage currents from nearby traces that are at different potentials.
• Cleaning the PCB following board assembly is recommended for best performance.
• Any precision integrated circuit can experience performance shifts resulting from moisture ingress into the
plastic package. Following any aqueous PCB cleaning process, TI recommends baking the PCB assembly to
remove moisture introduced into the device packaging during the cleaning process. A low temperature, postcleaning bake at 85°C for 30 minutes is sufficient for most circumstances.
24
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
OPA1652, OPA1654
www.ti.com
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
10.2 Layout Example
+
VIN A
+
VIN B
VOUT A
RG
VOUT B
RG
RF
RF
(Schematic Representation)
Place components
close to device and to
each other to reduce
parasitic errors
Output A
VS+
Output A
Use low-ESR,
ceramic bypass
capacitor. Place as
close to the device
as possible
GND
V+
RF
Output B
GND
-In A
Output B
+In A
-In B
RF
RG
VIN A
GND
RG
V±
Use low-ESR,
ceramic bypass
capacitor. Place as
close to the device
as possible
GND
+In B
VS±
Ground (GND) plane on another layer
VIN B
Keep input traces short
and run the input traces
as far away from
the supply lines
as possible
Copyright © 2016, Texas Instruments Incorporated
Figure 47. Operational Amplifier Board Layout for Noninverting Configuration
10.3 Power Dissipation
The OPA1652 and OPA1654 series op amps are capable of driving 2-kΩ loads with a power-supply voltage up to
±18 V and full operating temperature range. Internal power dissipation increases when operating at high supply
voltages. Copper leadframe construction used in the OPA165x series op amps improves heat dissipation
compared to conventional materials. Circuit board layout minimizes junction temperature rise. Wide copper
traces help dissipate the heat by acting as an additional heat sink. Temperature rise is further minimized by
soldering the devices to the circuit board rather than using a socket.
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
Submit Documentation Feedback
25
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
11 Device and Documentation Support
11.1 Device Support
11.1.1 Development Support
11.1.1.1 TINA-TI™ (Free Software Download)
TINA™ is a simple, powerful, and easy-to-use circuit simulation program based on a SPICE engine. TINA-TI™ is
a free, fully-functional version of the TINA software, preloaded with a library of macro models in addition to a
range of both passive and active models. TINA-TI provides all the conventional DC, transient, and frequency
domain analysis of SPICE, as well as additional design capabilities.
Available as a free download from the WEBENCH® Design Center, TINA-TI offers extensive post-processing
capability that allows users to format results in a variety of ways. Virtual instruments offer the ability to select
input waveforms and probe circuit nodes, voltages, and waveforms, creating a dynamic quick-start tool.
NOTE
These files require that either the TINA software (from DesignSoft™) or TINA-TI software
be installed. Download the free TINA-TI software from the TINA-TI folder.
11.1.1.2 DIP Adapter EVM
The DIP Adapter EVM tool provides an easy, low-cost way to prototype small surface mount devices. The
evaluation tool these TI packages: D or U (SOIC-8), PW (TSSOP-8), DGK (VSSOP-8), DBV (SOT23-6, SOT23-5
and SOT23-3), DCK (SC70-6 and SC70-5), and DRL (SOT563-6). The DIP Adapter EVM may also be used with
terminal strips or may be wired directly to existing circuits.
11.1.1.3 Universal Operational Amplifier EVM
The Universal Op Amp EVM is a series of general-purpose, blank circuit boards that simplify prototyping circuits
for a variety of IC package types. The evaluation module board design allows many different circuits to be
constructed easily and quickly. Five models are offered, with each model intended for a specific package type.
PDIP, SOIC, VSSOP, TSSOP and SOT-23 packages are all supported.
NOTE
These boards are unpopulated, so users must provide their own devices. TI recommends
requesting several op amp device samples when ordering the Universal Op Amp EVM.
11.1.1.4 Smart Amplifier Speaker Characterization Board Evaluation Module
The Smart Amplifier Speaker Characterization Board, when used in conjunction with a supported TI Smart
Amplifier and PurePath Console software, provides users the ability to measure speaker excursion, temperature
and other parameters for use with a TI Smart Amplifier products.
11.1.1.5 TI Precision Designs
TI Precision Designs are analog solutions created by TI’s precision analog applications experts and offer the
theory of operation, component selection, simulation, complete PCB schematic and layout, bill of materials, and
measured performance of many useful circuits. TI Precision Designs are available online at
http://www.ti.com/ww/en/analog/precision-designs/.
11.1.1.6 WEBENCH® Filter Designer
WEBENCH® Filter Designer is a simple, powerful, and easy-to-use active filter design program. The WEBENCH
Filter Designer allows the user to create optimized filter designs using a selection of TI operational amplifiers and
passive components from TI's vendor partners.
Available as a web-based tool from the WEBENCH® Design Center, WEBENCH® Filter Designer allows the
user to design, optimize, and simulate complete multistage active filter solutions within minutes.
26
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
OPA1652, OPA1654
www.ti.com
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
11.2 Documentation Support
11.2.1 Related Documentation
The following documents are relevant to using the OPA165x, and recommended for reference. All are available
for download at www.ti.com unless otherwise noted.
• OPA1652, OPA1654 EMIR Immunity Performance (SBOT007)
• Source resistance and noise considerations in amplifiers (SLYT470)
• Single-Supply Operation of Operational Amplifiers (SBOA059)
• Op Amp Performance Analysis (SBOA054)
• Compensate Transimpedance Amplifiers Intuitively (SBOA055)
• Tuning in Amplifiers (SBOA067)
• Feedback Plots Define Op Amp AC Performance (SBOA015)
• Active Volume Control for Professional Audio (TIDU034)
11.3 Related Links
Table 1 lists quick access links. Categories include technical documents, support and community resources,
tools and software, and quick access to sample or buy.
Table 1. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
OPA1652
Click here
Click here
Click here
Click here
Click here
OPA1654
Click here
Click here
Click here
Click here
Click here
11.4 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.5 Community Resource
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.6 Trademarks
TINA-TI, E2E are trademarks of Texas Instruments.
SoundPlus is a trademark of Texas Instruments Incorporated.
WEBENCH is a registered trademark of Texas Instruments.
Blu-Ray is a trademark of Blu-Ray Disc Association.
TINA, DesignSoft are trademarks of DesignSoft, Inc.
All other trademarks are the property of their respective owners.
11.7 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
Submit Documentation Feedback
27
OPA1652, OPA1654
SBOS477B – DECEMBER 2011 – REVISED DECEMBER 2016
www.ti.com
11.8 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
28
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: OPA1652 OPA1654
PACKAGE OPTION ADDENDUM
www.ti.com
2-Nov-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
OPA1652AID
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OP1652
Samples
OPA1652AIDGK
ACTIVE
VSSOP
DGK
8
80
RoHS & Green
NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
OUPI
Samples
OPA1652AIDGKR
ACTIVE
VSSOP
DGK
8
2500
RoHS & Green
NIPDAUAG | SN
Level-1-260C-UNLIM
-40 to 85
OUPI
Samples
OPA1652AIDR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OP1652
Samples
OPA1652AIDRGR
ACTIVE
SON
DRG
8
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OP1652
Samples
OPA1652AIDRGT
ACTIVE
SON
DRG
8
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OP1652
Samples
OPA1654AID
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OPA1654
Samples
OPA1654AIDR
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OPA1654
Samples
OPA1654AIPW
ACTIVE
TSSOP
PW
14
90
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OPA1654
Samples
OPA1654AIPWR
ACTIVE
TSSOP
PW
14
2000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
OPA1654
Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of