PTD08A015W
www.ti.com
SLTS296A – OCTOBER 2009 – REVISED FEBRUARY 2010
15-A, 4.75-V to 14-V INPUT, NON-ISOLATED,
WIDE-OUTPUT, DIGITAL POWERTRAIN™ MODULE
Check for Samples: PTD08A015W
FEATURES
APPLICATIONS
•
•
•
•
1
2
•
•
•
•
•
Up to 15-A Output Current
4.75-V to 14-V Input Voltage
Programmable Wide-Output Voltage
(0.7 V to 3.6 V)
Efficiencies up to 96%
Digital I/O
– PWM signal
– INHIBIT
– Current limit flag (FAULT)
– Sychronous Rectifier Enable (SRE)
Analog I/O
– Temperature
– Output currrent
Safety Agency Approvals: (Pending)
– UL/IEC/CSA-C22.2 60950-1
Operating Temperature: –40°C to 85°C
Digital Power Systems
using UCD9XXX Digital Controllers
DESCRIPTION
The PTD08A015W is a high-performance 15-A rated, non-isolated digital PowerTrain module. This module is the
power conversion section of a digital power system which incorporates TI's UCD7230 MOSFET driver IC. The
PTD08A015W must be used in conjunction with a digital power controller such as the UCD9240 or UCD9110
family. The PTD08A015W receives control signals from the digital controller and provides parametric and status
information back to the digital controller. Together, PowerTrain modules and a digital power controller form a
sophisticated, robust, and easily configured power management solution.
Operating from an input voltage range of 4.75 V to 14 V, the PTD08A015W provides step-down power
conversion to a wide range of output voltages from 0.7 V to 3.6 V. The wide input voltage range makes the
PTD08A015W particularly suitable for advanced computing and server applications that utilize a loosely
regulated 8-V, 9.6-V or 12-V intermediate distribution bus. Additionally, the wide input voltage range increases
design flexibility by supporting operation with tightly regulated 5-V or 12-V intermediate bus architectures.
The module incorporates output over-current and temperature monitoring which protects against most load faults.
Output current and module temperature signals are provided for the digital controller to permit user defined
over-current and over-temperature warning and fault scerarios.
The module uses double-sided surface mount construction to provide a low profile and compact footprint. The
PTD08A015W is constructed using through-hole pins and is lead (Pb) - free and RoHS compatible.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
POWERTRAIN is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009–2010, Texas Instruments Incorporated
PTD08A015W
SLTS296A – OCTOBER 2009 – REVISED FEBRUARY 2010
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
Standard PTD08A015W Application
Digital Lines
To/From
Digital Controller
12
11
VBIAS PWM
10
9
SRE FAULT
8
INH
VO
VI
1
VO
VI
4
PTD08A015W
+
CI2
CI1
22 mF
330 mF
(Recommended) (Required)[A]
L
O
A
D
+
GND
TEMP
2
5
IOUT AGND
6
7
GND
3
CO1
CO2
47 mF
330 mF
(Required)[A] (Recommended)
GND
GND
Analog Lines To
Digital Controller
UDG-09098
A.
2
[A] CI2 and CO1 are optional when the operating frequency is greater than 500 kHz.
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): PTD08A015W
PTD08A015W
www.ti.com
SLTS296A – OCTOBER 2009 – REVISED FEBRUARY 2010
ORDERING INFORMATION
For the most current package and ordering information, see the Package Option Addendum at the end of this datasheet, or see
the TI website at www.ti.com.
DATASHEET TABLE OF CONTENTS
DATASHEET SECTION
PAGE NUMBER
ENVIRONMENTAL AND ABSOLUTE MAXIMUM RATINGS
3
ELECTRICAL CHARACTERISTICS TABLE
4
TERMINAL FUNCTIONS
5
TYPICAL CHARACTERISTICS (VI = 12V)
6
TYPICAL CHARACTERISTICS (VI = 5V)
8
TYPICAL APPLICATION SCHEMATIC
10
GRAPHICAL USER INTERFACE VALUES
11
TRAY DRAWINGS
12
ENVIRONMENTAL AND ABSOLUTE MAXIMUM RATINGS
(Voltages are with respect to GND)
UNIT
VI
Input voltage
VB
Bias voltage
TA
Operating temperature range
Over VI range
Twave
Wave soldering temperature
Surface temperature of module body or pins for 5 seconds
maximum
Tstg
Storage temperature
(1)
V
16
V
–40 to 85
260
°C
–55 to 125 (1)
Mechanical shock
Per Mil-STD-883D, Method 2002.3, 1 msec, 1/2 sine, mounted
200
Mechanical vibration
Mil-STD-883D, Method 2007.2, 20-2000 Hz
15
Weight
MTBF
16
Reliability
Per Telcordia SR-332, 50% stress, TA = 40°C, ground benign
Flammability
Meets UL94V-O
G
3.9
grams
9.4
106 Hr
The shipping tray or tape and reel cannot be used to bake parts at temperatures higher than 65°C.
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): PTD08A015W
3
PTD08A015W
SLTS296A – OCTOBER 2009 – REVISED FEBRUARY 2010
www.ti.com
ELECTRICAL CHARACTERISTICS
PTD08A015W
TA= 25°C, FSW= 350kHz, VI= 12 V, VO= 3.3 V, VB= VI, CI1= 330 µF, CI2= 22 µF ceramic, CO1= 47 µF ceramic, CO2= 330 µF,
and IO= IO(max) (unless otherwise stated)
PARAMETER
TEST CONDITIONS
PTD08A015W
MIN
UNIT
MAX
IO
Output current
Over VO range
0
15
A
VI
Input voltage range
Over IO range
4.75
14 (1)
V
VOADJ
Output voltage adjust range
Over IO range
0.7 (1)
3.6
V
Efficiency
h
VOPP
VO Ripple (peak-to-peak)
VB
Bias voltage
VB
UVLO
Bias voltage under voltage
lockout
IB
Bias current
VIH
High-level input voltage
VIL
Low-level input voltage
PWM input
TEMP output
25°C, natural convection
TYP
VI = VB = 5 V
IO = 15 A,
fs = 350 kHz
VO = 3.3 V
94%
VO = 2.5 V
92%
VO = 1.8 V
89%
VO = 1.5 V
87%
VO = 1.2 V
85%
VO = 1.0 V
82%
20-MHz bandwidth
20
4.75
VB increasing
4.25
4.5
4.75
VB decreasing
4.0
4.25
4.5
Inhibit (pin 8) to AGND
Standby
4
Switching
34
2.0
SRE, INH, & PWM input levels
Frequency range
300
Pulse width limits
130
Range
-40
Accuracy, -40°C ≤ TA ≤ 85°C
VOL
FAULT output
ILIM
2.7
External output capacitance
Ceramic
(1)
(2)
(3)
(4)
(5)
4
0.6
V
mV/A
0.44
0.6
0.76
10
15
21
47
(3)
Nonceramic
Ceramic
A
110
(2)
1 (5)
330
(2)
330
(3)
V
3.5
85
22
°C
mV
3.3
60
Nonceramic
Equivalent series resistance (non-ceramic)
°C
25
Output Impedance
CO
125
500
0
Offset, IO = 0A, VO = 1.2V
Capacitance Value
kHz
mV/°C
0.15
External input capacitance
1000
6
Overcurrent threshold; Reset, followed by auto-recovery
IOUT output
V
10
Low-level output voltage, IFAULT = 4mA
Gain
V
ns
-4
Range
CI
5.5
Slope
High-level output voltage, IFAULT = 4mA
V
mA
0.8
Offset, TA = 0°C
VOH
mVPP
14
V
kΩ
µF
5000 (4)
(3)
µF
mΩ
The maximum input voltage is duty cycle limited to (VO/(130ns × FSW)) or 14 V, whichever is less. The maximum allowable input voltage
is a function of switching frequency.
A 22 µF ceramic input capacitor is required for proper operation. An additional 330 µF bulk capacitor rated for a minimum of 500mA rms
of ripple current is recommended. When operating at frequencies > 500kHz the 22 µF ceramic capacitor is only recommended. Refer to
the UCD9240 controller datasheet and user interface for application specific capacitor specifications.
A 47 µF ceramic output capacitor is required for basic operation. An additional 330 µF bulk capacitor is recommended for improved
transient response. When operating at frequencies > 500kHz the 47 µF ceramic capacitor is only recommended. Refer to the UCD9240
controller datasheet and user interface for application specific capacitor specifications.
5,000 µF is the calculated maximum output capacitance given a 1V/msec output voltage rise time. Additional capacitance or increasing
the output voltage rise rate may trigger the overcurrent threshold at start-up. Refer to the UCD9240 controller datasheet and user
interface for application specific capacitor specifications.
This is the minimum ESR for all non-ceramic output capacitance. Refer to the UCD9240 controller datasheet and user interface for
application specific capacitor specifications.
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): PTD08A015W
PTD08A015W
www.ti.com
SLTS296A – OCTOBER 2009 – REVISED FEBRUARY 2010
TERMINAL FUNCTIONS
TERMINAL
NAME
VI
NO.
1
GND
2
3
DESCRIPTION
The positive input voltage power node to the module, which is referenced to common GND.
This is the common ground connection for the VI and VO power connections.
VO
4
The regulated positive power output with respect to GND.
TEMP
5
Temperature sense output. The voltage level on this pin represents the temperature of the module.
IOUT
6
Current sense output. The voltage level on this pin represents the average output current of the module.
AGND
7
Analog ground return. It is the 0 Vdc reference for the control inputs.
INH (1)
8
The inhibit pin is a negative logic input that is referenced to AGND. Applying a low-level signal to this pin disables the
module and turns off the output voltage. A 10 kΩ pull-up to 3.3 V or 5 V is required if the INH signal is not used.
FAULT
9
Current limit flag. The Fault signal is a 3.3 V digital output which is latched high after an over-current condition. The
Fault is reset after two complete PWM cycles without an over-current condition (third rising edge of the PWM).
SRE
10
Synchronous Rectifier Enable. This pin is a high impedance digital input. A 3.3 V or 5 V logic level signals is used to
enable the synchronous rectifier switch. When this signal is high, the module will source and sink output current. When
this signal is low, the module will only source current.
PWM
11
This is the PWM input pin. It is a high impedance digital input that accepts 3.3 V or 5 V logic level signals up to 1 MHz.
VBIAS
12
Bias voltage supply required to power internal circuitry. For optimal performance connect VBIAS to VI.
(1)
Denotes negative logic: High = Normal operation, Low = Function active
1
12
11
10
9
8
7
6
5
Texas
Instruments
PTD08A015W
(Top View)
2
3
4
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): PTD08A015W
5
PTD08A015W
SLTS296A – OCTOBER 2009 – REVISED FEBRUARY 2010
www.ti.com
TYPICAL CHARACTERISTICS (VI = 12 V)
EFFICIENCY vs
LOAD CURRENT
EFFICIENCY vs
LOAD CURRENT
100
100
2.5 V
3.3 V
90
80
80
1.2 V
70
1.8 V
0.8 V
60
2.5 V
2.5 V
3.3 V
90
h – Efficiency – %
90
h – Efficiency – %
h – Efficiency – %
EFFICIENCY vs
LOAD CURRENT
100
3.3 V
(1)
1.8 V
70
1.2 V
60
80
70
1.8 V
1.2 V
60
0.8 V
0.8 V
0.6 V
50
0.6 V
fSW = 350 kHz
40
0
3
6
9
IO – Ouput Current – A
12
0
15
3
6
9
IO – Ouput Current – A
12
0
3
6
9
IO – Ouput Current – A
Figure 2.
Figure 3.
EFFICIENCY vs
LOAD CURRENT
POWER DISSIPATION
vs LOAD CURRENT
POWER DISSIPATION
vs LOAD CURRENT
6
1.2 V
60
5
3.3 V
PD – Power Dissipation – W
PD – Power Dissipation – W
1.8 V
70
4
2.5 V
3
1.8 V
2
1.2 V
1
50
fSW = 1 MHz
6
9
IO – Ouput Current – A
12
15
4
3
1.8 V
1.2 V
2
0.8 V
0.8 V
0
3
3.3 V
2.5 V
1
0.6 V
40
0.6 V
0
0
3
6
9
IO – Ouput Current – A
12
15
0
3
6
9
IO – Ouput Current – A
Figure 5.
Figure 6.
POWER DISSIPATION
vs LOAD CURRENT
POWER DISSIPATION
vs LOAD CURRENT
INPUT BIAS CURRENT vs
SWITCHING FREQUENCY
7
fSW = 1 MHz
PD – Power Dissipation – W
1.8 V
4
3
2
1.2 V
1
2.5 V
6
5
4
3.3 V
3
1.8 V
2
0.8 V
IBIAS – Input Bias Current – mA
3.3 V
5
80
60
40
VI = 12 V
1.2 V
0
1
3
6
9
IO – Ouput Current – A
12
Figure 7.
(1)
6
15
90
2.5 V
fSW = 750 kHz
0
12
Figure 4.
6
15
fSW = 500 kHz
5
80
12
6
fSW = 350 kHz
2.5 V
3.3 V
0
fSW = 750 kHz
40
15
Figure 1.
90
PD – Power Dissipation – W
fSW = 500 kHz
40
100
h – Efficiency – %
50
50
15
0
3
6
9
IO – Ouput Current – A
12
Figure 8.
15
20
300
400
500
600
700
800
900
fSW – Switching Frequency – kHz
1000
Figure 9.
The electrical characteristic data has been developed from actual products tested at 25°C. This data is considered typical for the
converter.
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): PTD08A015W
PTD08A015W
www.ti.com
SLTS296A – OCTOBER 2009 – REVISED FEBRUARY 2010
TYPICAL CHARACTERISTICS (VI = 12 V)
Safe Operating Area (1)
AMBIENT TEMPERATURE
vs LOAD CURRENT
90
AMBIENT TEMPERATURE
vs LOAD CURRENT
90
400 LFM
90
400 LFM
400 LFM
100 LFM
70
200 LFM
60
Nat Conv
50
40
fSW = 350 kHz
VO = 1.2 V
30
400LFM
200LFM
100LFM
Nat conv
20
80
70
TA – Ambient Temperature – °C
80
TA – Ambient Temperature – °C
TA – Ambient Temperature – °C
80
AMBIENT TEMPERATURE
vs LOAD CURRENT
Nat Conv
200 LFM
60
100 LFM
50
40
fSW = 500 kHz
VO = 1.2 V
30
400LFM
200LFM
100LFM
Nat conv
20
0
3
6
9
IO – Ouput Current – A
12
200 LFM
60
100 LFM
Nat Conv
50
40
fSW = 350 kHz
VO = 3.3 V
30
400LFM
200LFM
100LFM
Nat conv
20
0
15
70
3
Figure 10.
6
9
IO – Ouput Current – A
12
15
Figure 11.
0
3
6
9
IO – Ouput Current – A
12
15
Figure 12.
AMBIENT TEMPERATURE
vs LOAD CURRENT
90
400 LFM
TA – Ambient Temperature – °C
80
70
200 LFM
60
100 LFM
50
Nat Conv
40
fSW = 500 kHz
VO = 3.3 V
30
400LFM
200LFM
100LFM
Nat conv
20
0
3
6
9
IO – Ouput Current – A
12
15
Figure 13.
(1)
The temperature derating curves represent the conditions at which internal components are at or below the manufacturer's maximum
operating temperatures. Derating limits apply to modules soldered directly to a 100 mm x 100 mm double-sided PCB with 2 oz. copper.
Please refer to the mechanical specification for more information.
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): PTD08A015W
7
PTD08A015W
SLTS296A – OCTOBER 2009 – REVISED FEBRUARY 2010
www.ti.com
TYPICAL CHARACTERISTICS (VI = 5 V)
EFFICIENCY vs
LOAD CURRENT
100
3.3 V
(1)
EFFICIENCY vs
LOAD CURRENT
100
2.5 V
EFFICIENCY vs
LOAD CURRENT
100
3.3 V
3.3 V
2.5 V
90
0.6 V
0.8 V
70
1.8 V
1.2 V
60
90
80
0.8 V
1.2 V
1.8 V
70
2.5 V
0.6 V
60
50
50
100
6
9
IO – Ouput Current – A
12
0.8 V
3
6
9
IO – Ouput Current – A
12
15
0
3
6
9
IO – Ouput Current – A
Figure 14.
Figure 15.
Figure 16.
EFFICIENCY vs
LOAD CURRENT
POWER DISSIPATION
vs LOAD CURRENT
POWER DISSIPATION
vs LOAD CURRENT
fSW = 350 kHz
2.5 V
60
0.8 V
1.2 V
1.8 V
0.6 V
50
12
15
VO
4
3.3V
2.5V
1.8V
3
1.2V
0.8V
0.6V
PD – Power Dissipation – W
PD – Power Dissipation – W
70
15
fSW = 500 kHz
VO
90
80
12
5
5
3.3 V
1.8 V
60
40
0
15
1.2 V
0.6 V
fSW = 750 kHz
40
3
70
fSW = 500 kHz
40
0
80
50
fSW = 350 kHz
h – Efficiency – %
h – Efficiency – %
80
h – Efficiency – %
h – Efficiency – %
90
2
1
4
3.3V
2.5V
1.8V
3
1.2V
0.8V
0.6V
2
1
40
fSW = 1 MHz
30
0
0
0
3
6
9
IO – Ouput Current – A
12
15
0
6
9
IO – Ouput Current – A
12
15
0
Figure 19.
POWER DISSIPATION
vs LOAD CURRENT
POWER DISSIPATION
vs LOAD CURRENT
INPUT BIAS CURRENT vs
SWITCHING FREQUENCY
5
50
fSW = 1 MHz
VO
4
PD – Power Dissipation – W
3.3V
2.5V
1.8V
1.2V
0.8V
0.6V
2
3.3V
2.5V
1.8V
IBIAS – Input Bias Current – mA
VO
3
6
9
IO – Ouput Current – A
Figure 18.
fSW = 750 kHz
4
3
Figure 17.
5
PD – Power Dissipation – W
3
1.2V
0.8V
0.6V
3
2
1
1
0
0
40
30
20
VI = 5 V
0
3
6
9
IO – Ouput Current – A
12
Figure 20.
(1)
8
15
0
3
6
9
IO – Ouput Current – A
12
Figure 21.
15
10
300
400
500
600
700
800
900
fSW – Switching Frequency – kHz
1000
Figure 22.
The electrical characteristic data has been developed from actual products tested at 25°C. This data is considered typical for the
converter.
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): PTD08A015W
PTD08A015W
www.ti.com
SLTS296A – OCTOBER 2009 – REVISED FEBRUARY 2010
TYPICAL CHARACTERISTICS (VI = 5 V)
Safe Operating Area (1)
AMBIENT TEMPERATURE
vs LOAD CURRENT
90
AMBIENT TEMPERATURE
vs LOAD CURRENT
90
400 LFM
400 LFM
Nat Conv
70
200 LFM
60
100 LFM
50
40
fSW = 350 kHz
VO = 1.2 V
30
400LFM
200LFM
100LFM
Nat conv
80
TA – Ambient Temperature – °C
TA – Ambient Temperature – °C
TA – Ambient Temperature – °C
90
400 LFM
80
80
20
0
AMBIENT TEMPERATURE
vs LOAD CURRENT
Nat Conv
70
200 LFM
60
100 LFM
50
40
fSW = 500 kHz
VO = 1.2 V
30
400LFM
200LFM
100LFM
Nat conv
20
3
6
9
IO – Ouput Current – A
12
200 LFM
100 LFM
60
50
40
fSW = 350 kHz
VO = 3.3 V
30
400LFM
200LFM
100LFM
Nat conv
20
0
15
Nat Conv
70
3
Figure 23.
6
9
IO – Ouput Current – A
12
15
Figure 24.
0
3
6
9
IO – Ouput Current – A
12
15
Figure 25.
AMBIENT TEMPERATURE
vs LOAD CURRENT
90
400 LFM
TA – Ambient Temperature – °C
80
Nat Conv
70
200 LFM
100 LFM
60
50
40
fSW = 500 kHz
VO = 3.3 V
30
400LFM
200LFM
100LFM
Nat conv
20
0
3
6
9
IO – Ouput Current – A
12
15
Figure 26.
(1)
The temperature derating curves represent the conditions at which internal components are at or below the manufacturer's maximum
operating temperatures. Derating limits apply to modules soldered directly to a 100 mm x 100 mm double-sided PCB with 2 oz. copper.
Please refer to the mechanical specification for more information.
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): PTD08A015W
9
PTD08A015W
SLTS296A – OCTOBER 2009 – REVISED FEBRUARY 2010
www.ti.com
APPLICATION INFORMATION
DIgital Power
VIN
0.1 mF
10 kW
82.5 kW
VIN
VBIAS
+3.3 V
FCX491A
FAULT
UCD7230 Driver
TEMP
+3.3 V
PWM
4.7 mF
Temp-rail1A
PTD08A020W
Temp Sensor
Commutation
VO
SRE
Logic
0.1 mF
INH
[A]
–Vsens-rail2
+Vsens-rail3
–Vsens-rail3
+Vsens-rail4
–Vsens-rail4
55
56
CS-rail3A
CS-rail4A
CS-rail1B
CS-rail2B
7
44
45
47
BPCap
DPWM-1B
DPWM-2B
DPWM-3A
EAn3
DPWM-4A
EAp4
57
FAULT-1A
EAn4
FAULT-1B
AddrSens0
FAULT-2A
AddrSens1
59
FAULT-2B
CS-1A(COMP1)
3
FAULT-3A
CS-2A(COMP2)
2
FAULT-4A
CS-3A(COMP3)
1
SRE-1A
CS-4A(COMP4)
63
UCD9240RGC
CS-1B
62
SRE-1B
SRE-2A
CS-2B
4
SRE-2B
Vin/Iin
5
SRE-3A
Vtrack
6
SRE-4A
Temp
15
TMUX-0
PMBus-Clk
16
TMUX-1
PMBus-Data
27
TMUX-2
PMBus-Alert
28
39
PMBus-Ctrl
FAN-PWM
PowerGood (TMS)
FAN-TACH
10 kW
SYNC-IN
16
Temp-rail1A
Temp-rail1B
Temp-rail2A
Temp-rail2B
Temp-rail3A
Temp-rail4A
13
14
15
12
1
5
2
4
Dgnd-3
Dgnd-2
43
26
Dgnd-1
8
Agnd-2
Agnd-3
64
49
RESET
48
9
Agnd-1
SYNC-OUT
+3.3 V 10 kW
IOUT
GND
DPWM-1A
DPWM-2A
EAp3
60
CS-rail2A
INH
CS-rail1A
EAn2
54
61
CS-rail1A
46
EAp2
53
V33DIO-2
EAn1
52
V33DIO-1
EAp1
51
V33A
–Vsens-rail1
+Vsens-rail2
50
V33FB
+Vsens-rail1
V33D
52
15 kW
TRST
RCR
17
VIN
Temp-rail1B
18
19
FAULT
20
VBIAS
PTD08A020W
SRE
23
INH
A1
A2
A3
A4
A5
Com
S2
S1
S0
EN
GND
11
12
+Vsens-rail1
–Vsens-rail1
CS-rail1B
13
VIN
14
25
Temp-rail2A
34
FAULT
22
PWM
24
SRE
33
INH
VBIAS
VIN
TEMP
PTD08A015W
GND
35
CS-rail2A
29
VIN
Temp-rail2B
30
FAULT
31
36
38
37
TEMP
INH
FAN-PWM
VIN
PTD08A015W
SRE
42
41
VBIAS
PWM
32
GND
CS-rail2B
+Vsens-rail2
–Vsens-rail2
FAN-Tach
VIN
SyncIn
SyncOut
Temp-rail3A
40
10
10 kW
FAULT
VBIAS
VIN
TEMP
PWM
PTD08A010W
SRE
6
A6
A7
CD74HC4051
VOUT
GND
IOUT
+Vsens-rail3
–Vsens-rail3
VIN
Temp-rail4A
8
11
VOUT
IOUT
3
10
VOUT
IOUT
CS-rail3A
A0
VOUT
IOUT
INH
+3.3 V
VIN
TEMP
PWM
21
FAULT
VBIAS
VIN
TEMP
PWM
PTD08A010W
SRE
INH
CS-rail4A
VOUT
GND
IOUT
+Vsens-rail4
–Vsens-rail4
UDG-09097
Figure 27. Typical Application Schematic
A. This discrete bias power circuit may be substituted with a low dropout regulator (LDO). For example, TPS715A33
can provide bias power to the UCD9240.
Figure 27 shows the UCD9240 power supply controller working in a system which requires the regulation of four
independent power supplies. The loop for each power supply is created by the respective voltage outputs feeding
into the Error ADC differential inputs, and completed by DPWM outputs feeding into the UCD7230 drivers which
are shown on the PTD08A0x0W modules.
10
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): PTD08A015W
PTD08A015W
www.ti.com
SLTS296A – OCTOBER 2009 – REVISED FEBRUARY 2010
UCD9240 Graphical User Interface (GUI)
When using the UCD9240 digital controller along with digital PowerTrain modules to design a digital power
system, several internal parameters of the modules are required to run the Fusion Digital Power Designer GUI.
See the plant parameters below for the PTD08A015W digital PowerTrain modules.
Table 1. PTD08A015W Plant Parameters
PTD08A015W Plant Parameters
L (µH)
DCR (mΩ)
Rds-on-hi (mΩ)
Rds-on-lo (mΩ)
0.90
2.2
3.6
3.6
Internal output capacitance is present on the digital PowerTrain modules themselves. When using the GUI
interface this capacitance information must be included along with any additional external capacitance. See the
capacitor parameters below for the PTD08A015W digital PowerTrain modules.
Table 2. PTD08A015W Capacitor Parameters
PTD08A015W Capacitor Parameters
C (µF)
ESR (mΩ)
ESL (nH)
Quantity
47
1.5
2.5
1
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): PTD08A015W
11
PTD08A015W
SLTS296A – OCTOBER 2009 – REVISED FEBRUARY 2010
www.ti.com
TRAY
12
Submit Documentation Feedback
Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): PTD08A015W
PACKAGE OPTION ADDENDUM
www.ti.com
19-Dec-2019
PACKAGING INFORMATION
Orderable Device
Status
(1)
PTD08A015WAD
ACTIVE
Package Type Package Pins Package
Drawing
Qty
ThroughHole Module
EGS
12
36
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
RoHS (In
Work) & Green
(In Work)
SN
Level-1-235C-UNLIM/
Level-3-260C-168HRS
Op Temp (°C)
Device Marking
(4/5)
-40 to 85
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
