SN54HC367, SN74HC367
SCLS309E – JANUARY 1996 – REVISED MARCH 2022
SNx4HC367 Hex Buffers and Line Drivers with 3-State Outputs
1 Features
2 Description
•
•
The SNx4HC367 is a hex buffer with 3-state outputs.
The device is configured into two banks, one with four
drivers and one with two drivers, each controlled by its
own output enable pin.
•
•
•
•
•
Wide operating voltage range of 2 V to 6 V
High-current 3-state outputs drive bus lines, buffer
memory address registers, or drive up to 15
LSTTL loads
True outputs
Low power consumption, 80-μA max ICC
Typical tpd = 10 ns
±6-mA output drive at 5 V
Low input current of 1µA max
Device Information
PACKAGE
BODY SIZE (NOM)
SN54HC367J
CDIP (16)
24.38 mm × 6.92 mm
SN74HC367D
SOIC (16)
9.90 mm × 3.90 mm
SN74HC367N
PDIP (16)
19.31 mm × 6.35 mm
SN74HC367NS
SO (16)
6.20 mm × 5.30 mm
SN74HC367PW
TSSOP (16)
5.00 mm × 4.40 mm
(1)
1OE
1A1
1A2
1A3
1A4
1
2OE
2
3
4
5
6
7
9
10
(1)
PART NUMBER
1Y1
2A1
1Y2
2A2
For all available packages, see the orderable addendum at
the end of the data sheet.
15
12
11
14
13
2Y1
2Y2
1Y3
1Y4
Functional Block Diagram
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
SN54HC367, SN74HC367
www.ti.com
SCLS309E – JANUARY 1996 – REVISED MARCH 2022
Table of Contents
1 Features............................................................................1
2 Description.......................................................................1
3 Revision History.............................................................. 2
4 Pin Configuration and Functions...................................3
5 Specifications.................................................................. 4
5.1 Absolute Maximum Ratings........................................ 4
(1)
5.2 Recommended Operating Conditions ..................... 4
5.3 Thermal Information....................................................4
5.4 Electrical Characteristics.............................................5
5.5 Switching Characteristics ...........................................5
5.6 Operating Characteristics........................................... 6
6 Parameter Measurement Information............................ 7
7 Detailed Description........................................................8
7.1 Overview..................................................................... 8
7.2 Functional Block Diagram........................................... 8
7.3 Device Functional Modes............................................8
8 Power Supply Recommendations..................................9
9 Layout...............................................................................9
9.1 Layout Guidelines....................................................... 9
10 Device and Documentation Support..........................10
10.1 Documentation Support.......................................... 10
10.2 Receiving Notification of Documentation Updates..10
10.3 Support Resources................................................. 10
10.4 Trademarks............................................................. 10
10.5 Electrostatic Discharge Caution..............................10
10.6 Glossary..................................................................10
11 Mechanical, Packaging, and Orderable
Information.................................................................... 10
3 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision D (September 2003) to Revision E (March 2022)
Page
• Updated the numbering, formatting, tables, figures, and cross-references throughout the doucment to reflect
modern data sheet standards............................................................................................................................. 1
2
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: SN54HC367 SN74HC367
SN54HC367, SN74HC367
www.ti.com
SCLS309E – JANUARY 1996 – REVISED MARCH 2022
4 Pin Configuration and Functions
J, D, N, NS, or PW package
16-Pin CDIP, SOIC, PDIP, SO, or TSSOP
Top View
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: SN54HC367 SN74HC367
3
SN54HC367, SN74HC367
www.ti.com
SCLS309E – JANUARY 1996 – REVISED MARCH 2022
5 Specifications
5.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
VCC
Supply voltage range
(2)
IIK
Input clamp current
IOK
Output clamp current
IO
Continuous output current
(2)
MIN
MAX
-0.5
7
Junction temperature
Tstg
Storage temperature
(1)
(2)
V
(VI < 0 or VI > VCC)
±20
mA
(VO < 0 or VO > VCC)
±20
mA
(VO = 0 to VCC)
±35
mA
±70
mA
150
°C
150
°C
Continuous current through VCC or GND
TJ
UNIT
-65
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
(1)
5.2 Recommended Operating Conditions
SN54HC367
VCC
NOM
MAX
2
5
6
Supply voltage
VCC = 2 V
VIH
High-level input voltage
VCC = 4.5 V
VI
Input voltage
VO
Output voltage
TA
(1)
2
5
6
3.15
4.2
4.2
VCC = 4.5 V
0
0.5
0.5
1.35
0
VCC
0
V
VCC
V
VCC = 4.5 V
500
500
VCC = 6 V
400
400
125
V
VCC
1000
-55
V
1.8
VCC
1000
Operating free-air temperature
UNIT
V
1.35
1.8
0
VCC = 2 V
Input transition rise/fall time
MAX
3.15
VCC = 6 V
tt
NOM
1.5
VCC = 2 V
Low-level input voltage
MIN
1.5
VCC = 6 V
VIL
SN74HC367
MIN
-40
85
ns
°C
All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report
Implications of Slow or Floating SMOS Inputs, literature number SCBA004.
5.3 Thermal Information
THERMAL METRIC
RθJA
(1)
4
Junction-to-ambient thermal
(1)
resistance
D (SOIC)
N (PDIP)
NS (SO)
PW (TSSOP)
16 PINS
16 PINS
16 PINS
16 PINS
UNIT
73
67
64
108
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC package thermal metrics application
report.
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: SN54HC367 SN74HC367
SN54HC367, SN74HC367
www.ti.com
SCLS309E – JANUARY 1996 – REVISED MARCH 2022
5.4 Electrical Characteristics
over recommended operating free-air temperature range (unless otherwise noted)
TEST
(1)
CONDITIONS
PARAMETER
VCC (V)
IOH = −20 μA
MAX
MIN
SN74HC367
TYP
2
1.9
1.998
1.9
1.9
4.5
4.4
4.499
4.4
4.4
6
5.9
5.999
5.9
5.9
4.5
3.98
4.3
3.7
3.84
6
5.48
5.8
5.2
5.34
IOH = −5.2 mA
MAX
MIN
UNIT
MAX
V
2
0.002
0.1
0.1
0.1
IOL = 20 μA
4.5
0.001
0.1
0.1
0.1
6
0.001
0.1
0.1
0.1
IOL = 4 mA
4.5
0.17
0.26
0.4
0.33
IOL = 5.2 mA
6
0.15
0.26
0.4
0.33
VOL
V
II
VI = VCC or 0
6
±0.1
±100
±1000
±1000
nA
IOZ
VO = VCC or 0
6
±0.01
±0.5
±10
±5
μA
ICC
VI = VCC or 0, IO
=0
6
8
160
80
μA
10
10
10
pF
Ci
(1)
SN54HC367
MIN
VOH
IOH = −4 mA
TA = 25°C
2 to 6
3
VI = VIH or VIL, unless otherwise noted.
5.5 Switching Characteristics
over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (See Figure 6)
PARAMETER
tpd
ten
tdis
tt
Propagation delay
Enable time
Diable time
FROM
(INPUT)
TO (OUTPUT)
VCC
(V)
A
Y
OE
OE
Transition time
Y
Y
Any
TA = 25°C
MIN
SN54HC367
MIN
MAX
SN74HC367
TYP
MAX
MIN
MAX
2
50
95
145
120
4.5
12
19
29
24
6
10
16
25
20
2
100
190
285
238
4.5
26
38
57
48
6
21
32
48
41
2
50
175
265
240
4.5
21
35
53
48
6
19
30
45
41
2
28
60
90
75
4.5
8
12
18
15
6
6
10
15
13
ns
ns
ns
ns
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: SN54HC367 SN74HC367
5
SN54HC367, SN74HC367
www.ti.com
SCLS309E – JANUARY 1996 – REVISED MARCH 2022
5.5 Switching Characteristics
over recommended operating free-air temperature range, CL = 150 pF (unless otherwise noted) (See Figure 6)
PARAMETER
tpd
ten
tt
Propagation delay
Enable time
FROM
(INPUT)
TO (OUTPUT)
VCC
(V)
A
Y
OE
Transition time
Y
Any
TA = 25°C
MIN
SN54HC367
MIN
MAX
SN74HC367
TYP
MAX
MIN
MAX
2
70
120
180
150
4.5
17
24
36
30
6
14
20
31
25
2
140
230
345
285
4.5
30
46
69
57
6
28
39
59
48
2
45
210
315
265
4.5
17
42
63
53
6
13
36
53
45
ns
ns
ns
5.6 Operating Characteristics
TA = 25°C
Cpd
6
Power dissipation capacitance per buffer/driver
Test Conditions
TYP
UNIT
No load
35
pF
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: SN54HC367 SN74HC367
SN54HC367, SN74HC367
www.ti.com
SCLS309E – JANUARY 1996 – REVISED MARCH 2022
6 Parameter Measurement Information
Figure 6-1. Load Circuit
Figure 6-2. Voltage Waveforms
Propagation Delay and Output Transition Times
Figure 6-3. Voltage Waveforms
Enable and Disable Times for 3-State Outputs
Figure 6-4. Voltage Waveforms
Input Rise and Fall TImes
A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low except when diabled by the
output control.
Waveform 2 is for an output with internal conditions such that the output is high except when diabled by the
output control.
C. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators
having the following charactersitics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 6 ns, tf = 6 ns.
D. The outputs are measured one at a time with one input transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tpd is the maximum between tPLH and tPHL.
H. tt is the maximum between tTLH and tTHL.
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: SN54HC367 SN74HC367
7
SN54HC367, SN74HC367
www.ti.com
SCLS309E – JANUARY 1996 – REVISED MARCH 2022
7 Detailed Description
7.1 Overview
These hex buffers and line drivers are designed specifically to improve both the performance and density of
3-state memory address drivers, clock drivers, and bus-oriented receivers and transmitters. The ’HC367 devices
are organized as dual 4-line and 2-line buffers/drivers with active-low output-enable (1OE and 2OE) inputs.
When OE is low, the device passes noninverted data from the A inputs to the Y outputs. When OE is high, the
outputs are in the high-impedance state.
7.2 Functional Block Diagram
1OE
1A1
1A2
1A3
1A4
1
15
2OE
2
3
4
5
6
7
9
10
1Y1
2A1
1Y2
2A2
12
11
14
13
2Y1
2Y2
1Y3
1Y4
Pin numbers hown are for the D, J, N, NS, PW, and W packages.
Figure 7-1. Functional Block Diagram
7.3 Device Functional Modes
Table 7-1. Function Table
(each buffer/driver)
INPUTS
OE
8
OUTPUT
A
Y
H
X
Z
L
H
H
L
L
L
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: SN54HC367 SN74HC367
SN54HC367, SN74HC367
www.ti.com
SCLS309E – JANUARY 1996 – REVISED MARCH 2022
8 Power Supply Recommendations
The power supply can be any voltage between the minimum and maximum supply voltage rating located in the
Recommended Operating Conditions. Each VCC terminal should have a good bypass capacitor to prevent power
disturbance. A 0.1-μF capacitor is recommended for this device. It is acceptable to parallel multiple bypass caps
to reject different frequencies of noise. The 0.1-μF and 1-μF capacitors are commonly used in parallel. The
bypass capacitor should be installed as close to the power terminal as possible for best results.
9 Layout
9.1 Layout Guidelines
When using multiple-input and multiple-channel logic devices inputs must not ever be left floating. In many
cases, functions or parts of functions of digital logic devices are unused; for example, when only two inputs of a
triple-input AND gate are used or only 3 of the 4 buffer gates are used. Such unused input pins must not be left
unconnected because the undefined voltages at the outside connections result in undefined operational states.
All unused inputs of digital logic devices must be connected to a logic high or logic low voltage, as defined by the
input voltage specifications, to prevent them from floating. The logic level that must be applied to any particular
unused input depends on the function of the device. Generally, the inputs are tied to GND or VCC, whichever
makes more sense for the logic function or is more convenient.
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: SN54HC367 SN74HC367
9
SN54HC367, SN74HC367
www.ti.com
SCLS309E – JANUARY 1996 – REVISED MARCH 2022
10 Device and Documentation Support
TI offers an extensive line of development tools. Tools and software to evaluate the performance of the device,
generate code, and develop solutions are listed below.
10.1 Documentation Support
10.1.1 Related Documentation
10.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on
Subscribe to updates to register and receive a weekly digest of any product information that has changed. For
change details, review the revision history included in any revised document.
10.3 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
10.4 Trademarks
TI E2E™ is a trademark of Texas Instruments.
All trademarks are the property of their respective owners.
10.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
10.6 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
11 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
10
Submit Document Feedback
Copyright © 2022 Texas Instruments Incorporated
Product Folder Links: SN54HC367 SN74HC367
PACKAGE OPTION ADDENDUM
www.ti.com
30-Mar-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
8500201EA
ACTIVE
CDIP
J
16
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
8500201EA
SNJ54HC367J
JM38510/65708BEA
ACTIVE
CDIP
J
16
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
JM38510/
65708BEA
M38510/65708BEA
ACTIVE
CDIP
J
16
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
JM38510/
65708BEA
SN54HC367J
ACTIVE
CDIP
J
16
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
SN54HC367J
SN74HC367D
ACTIVE
SOIC
D
16
40
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
HC367
SN74HC367DR
ACTIVE
SOIC
D
16
2500
RoHS & Green
NIPDAU | SN
Level-1-260C-UNLIM
-40 to 85
HC367
SN74HC367DRE4
ACTIVE
SOIC
D
16
2500
TBD
Call TI
Call TI
-40 to 85
SN74HC367DT
ACTIVE
SOIC
D
16
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
HC367
SN74HC367N
ACTIVE
PDIP
N
16
25
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 85
SN74HC367N
SN74HC367NSR
ACTIVE
SO
NS
16
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
HC367
SN74HC367PW
ACTIVE
TSSOP
PW
16
90
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
HC367
SN74HC367PWR
ACTIVE
TSSOP
PW
16
2000
RoHS & Green
NIPDAU | SN
Level-1-260C-UNLIM
-40 to 85
HC367
SN74HC367PWT
ACTIVE
TSSOP
PW
16
250
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 85
HC367
SNJ54HC367J
ACTIVE
CDIP
J
16
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
8500201EA
SNJ54HC367J
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
30-Mar-2022
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of