TLV5614MPWREP

  
  
µ   

  
 
    SGLS355 − JUNE 2006 D Controlled Baseline D D D D D D D D D D D − One Assembly − One Test Site − One Fabrication Site Extended Temperature Performance of −55°C to 125°C Enhanced Diminishing Manufacturing Sources (DMS) Support Enhanced Product-Change Notification Qualification Pedigree† Four 12-Bit Digital-to-Analog Converters (DACs) Programmable Settling Time of Either 3 µs or 9 µs (Typ) TMS320E DSP Family, (Q)SPI, and Microwire Compatible Serial Interface Internal Power-On Reset Low Power Consumption: 8 mW, Slow Mode − 5-V Supply 3.6 mW, Slow Mode − 3-V Supply Reference Input Buffer Voltage Output Range . . . 2× the Reference Input Voltage D Monotonic Overtemperature D Dual 2.7-V to 5.5-V Supply (Separate Digital and Analog Supplies) D Hardware Power Down (10 nA) D Software Power Down (10 nA) D Simultaneous Update applications D D D D D D Battery-Powered Test Instruments Digital Offset and Gain Adjustment Industrial Process Controls Machine and Motion Control Devices Communications Arbitrary Waveform Generation † Component qualification in accordance with JEDEC and industry standards to ensure reliable operation over an extended temperature range. This includes, but is not limited to, Highly Accelerated Stress Test (HAST) or biased 85/85, temperature cycle, autoclave or unbiased HAST, electromigration, bond intermetallic life, and mold compound life. Such qualification testing should not be viewed as justifying use of this component beyond specified performance and environmental limits. PW PACKAGE (TOP VIEW) description DVDD PD LDAC DIN SCLK CS FS DGND 1 16 AVDD REFINAB OUTA OUTB OUTC OUTD REFINCD AGND 15 2 The TLV5614 is a quadruple 12-bit voltage output 14 3 digital-to-analog converter (DAC) with a flexible 13 4 four-wire serial interface. The four-wire serial 12 5 interface allows glueless interface to TMS320 11 6 DSP family, SPI, QSPI, and Microwire serial 10 7 ports. The TLV5614 is programmed with a 16-bit 9 8 serial word comprised of a DAC address, individual DAC control bits, and a 12-bit DAC value. The device has provision for two supplies – one digital supply for the serial interface (via pins DVDD and DGND), and one for the DACs, reference buffers, and output buffers (via pins AVDD and AGND). Each supply is independent of the other and can be any value between 2.7 V and 5.5 V. The dual supplies allow a typical application where the DAC is controlled via a microprocessor operating on a 3-V supply (also used on pins DVDD and DGND), with the DACs operating on a 5-V supply. The digital and analog supplies can be tied together. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. TMS320 is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. Copyright  2006, Texas Instruments Incorporated 
 
 !"#$%!  &'""(% $ ! )'*+&$%! ,$%( "!,'&% &!!"# %! )(&&$%! )(" %-( %("# !
(.$ %"'#(% %$,$", /$""$%0 "!,'&%! )"!&(1 ,!( !% (&($"+0 &+',( %(%1 ! $++ )$"$#(%(" POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 description (continued) The resistor string output voltage is buffered by a 2× gain rail-to-rail output buffer. The buffer features a Class AB output stage to improve stability and reduce settling time. A rail-to-rail output stage and a power-down mode makes it ideal for single-voltage, battery-based applications. The settling time of the DAC is programmable to allow the designer to optimize speed versus power dissipation. The settling time is chosen by the control bits within the 16-bit serial input string. A high-impedance buffer is integrated on the REFINAB and REFINCD terminals to reduce the need for a low source-impedance drive to the terminal. REFINAB and REFINCD allow DAC A and B to have a different reference voltage than DAC C and D. The TLV5614 is implemented with a CMOS process and is available in a 16-terminal TSSOP package. The TLV5614M is characterized for operation from −55°C to 125°C. AVAILABLE OPTIONS PACKAGE 2 TA TSSOP (PW) −55°C to 125°C TLV5614MPWREP POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 functional block diagram AVDD REFINAB 15 DVDD 16 1 DAC A + _ Power-On Reset DIN 4 Serial Input Register 14 + _ 14-Bit Data and Control Register 12 12-Bit DAC Latch 2 2-Bit Control Data Latch 14 OUTA 10 2 2 Power Down/ Speed Control 2 7 FS SCLK CS REFINCD 5 6 DAC Select/ Control Logic 13 DAC B DAC C 12 DAC D 11 OUTB OUTC 10 3 9 AGND OUTD 2 8 DGND LDAC POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PD 3 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 Terminal Functions TERMINAL NAME NO. AGND 9 AVDD CS 16 DGND 8 DIN 4 DVDD 1 6 I/O DESCRIPTION Analog ground Analog supply I Chip select. This terminal is active low. Digital ground I Serial data input Digital supply 7 I Frame synchronization. The falling edge of the frame synchronization pulse indicates the start of a serial data frame shifted out to the TLV5614. 2 I Power down. Powers down all DACs (overriding their individual power down settings) and all output stages. This terminal is active low. 3 I Load DAC. When LDAC is high, no DAC output updates occur when the input digital data is read into the serial interface. The DAC outputs are only updated when LDAC is low. REFINAB 15 I Voltage reference input for DAC A and B REFINCD 10 I Voltage reference input for DAC C and D FS PD LDAC SCLK 5 I Serial clock input OUTA 14 O DAC A OUTB 13 O DAC B OUTC 12 O DAC C OUTD 11 O DAC D 10000 Wirebond Voiding Fail Mode Years Estimated Life 1000 100 Electromigration Fail Mode 10 1 80 90 100 110 120 Continuous TJ − 5C Figure 1. Operating Life Derating Chart 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 130 140 150 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, (DVDD, AVDD to GND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Supply voltage difference (AVDD to DVDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −2.8 V to 2.8 V Digital input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to DVDD + 0.3 V Reference input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to AVDD + 0.3 V Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 125°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C Lead temperature 1,6 mm (1/16 in) from case for 10 s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. recommended operating conditions Supply voltage, AVDD, DVDD High-level digital input voltage, VIH Low-level digital input voltage, VIL Reference voltage, Vref to REFINAB, REFINCD terminal MIN NOM MAX 5-V supply 4.5 5 5.5 3-V supply 2.7 3 3.3 DVDD = 2.7 V 2 DVDD = 5.5 V 2.4 0.6 DVDD = 5.5 V 1 5-V supply, See Note 1 0 2.048 3-V supply, See Note 1 0 1.024 2 10 Load capacitance, CL Serial clock rate, SCLK Operating free-air temperature −55 Package thermal resistance, junction to ambient, θJA V V DVDD = 2.7 V Load resistance, RL UNIT 108.4 VDD − 1.5 VDD − 1.5 V V kΩ 100 pF 20 MHz 125 °C/W °C/W NOTE 1: Voltages greater than AVDD/2 cause output saturation for large DAC codes. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 electrical characteristics over recommended operating free-air temperature range, Vref = 2.048 V, AVDD = DVDD = 5 V and Vref = 1.024 V for AVDD = DVDD = 3 V (unless otherwise noted) static DAC specifications PARAMETER TEST CONDITIONS MIN Resolution EZS EG TYP MAX UNIT ±4 LSB ±1 LSB 12 bits Integral nonlinearity (INL), end point adjusted See Note 1 ±1.5 Differential nonlinearity (DNL) See Note 2 ±0.5 Zero-scale error (offset error at zero scale) See Note 3 Zero-scale error temperature coefficient See Note 4 Gain error See Note 5 Gain-error temperature coefficient See Note 6 ±12 10 ±0.7 Zero scale PSRR Power-supply rejection ratio Full scale See Note 7 and Note 8 mV ppm/°C % of FS voltage 10 ppm/°C −80 dB −80 dB NOTES: 1. The relative accuracy or integral nonlinearity (INL), sometimes referred to as linearity error, is the maximum deviation of the output from the line between zero and full scale excluding the effects of zero code and full-scale errors. 2. The differential nonlinearity (DNL), sometimes referred to as differential error, is the difference between the measured and ideal 1-LSB amplitude change of any two adjacent codes. Monotonic means the output voltage changes in the same direction (or remains constant) as a change in the digital input code. 3. Zero-scale error is the deviation from zero voltage output when the digital input code is zero. 4. Zero-scale-error temperature coefficient is given by: EZS TC = [EZS (Tmax) − EZS (Tmin)E/Vref × 106/(Tmax − Tmin). 5. Gain error is the deviation from the ideal output (2 Vref − 1 LSB) with an output load of 10 kΩ, excluding the effects of the zero error. 6. Gain temperature coefficient is given by: EG TC = [EG(Tmax) − EG (Tmin)]/Vref × 106/(Tmax − Tmin). 7. Zero-scale-error rejection ratio (EZS-RR) is measured by varying the AVDD from 5 ± 0.5 V and 3 ± 0.3 V dc, and measuring the proportion of this signal imposed on the zero-code output voltage. 8. Full-scale rejection ratio (EG-RR) is measured by varying the AVDD from 5 ± 0.5 V and 3 ± 0.3 V dc and measuring the proportion of this signal imposed on the full-scale output voltage after subtracting the zero-scale change. individual DAC output specifications PARAMETER VO TEST CONDITIONS Voltage output range RL = 10 kΩ Output load regulation accuracy RL = 2 kΩ vs 10 kΩ MIN TYP 0 MAX AVDD−0.4 0.1 UNIT V 0.25 % of FS voltage MAX UNIT reference inputs (REFINAB, REFINCD) PARAMETER VI RI Input voltage range CI Input capacitance TEST CONDITIONS MIN See Note 1 TYP 0 Input resistance Reference feed through REFIN = 1 VPP at 1 kHz + 1.024 Vdc (see Note 2) Reference input bandwidth REFIN = 0.2 VPP + 1.024-Vdc large signal AVDD−1.5 V 10 MΩ 5 pF −75 dB Slow 0.5 Fast 1 MHz NOTES: 1. Reference input voltages greater than VDD/2 cause output saturation for large DAC codes. 2. Reference feedthrough is measured at the DAC output, with an input code = 000 hex and a Vref (REFINAB or REFINCD) input = 1.024 Vdc + 1 VPP at 1 kHz. 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 electrical characteristics over recommended operating free-air temperature range, Vref = 2.048 V, AVDD = DVDD = 5 V and Vref = 1.024 V for AVDD = DVDD = 3 V (unless otherwise noted) (continued) digital inputs (DIN, CS, LDAC, PD) PARAMETER IIH IIL High-level digital input current CI Input capacitance TEST CONDITIONS MIN TYP VI = VDD VI = 0 V Low-level digital input current MAX UNIT ±1 µA ±1 µA 3 pF power supply PARAMETER IDD TEST CONDITIONS Power-supply current TYP MAX 5-V supply, No load, Clock running, All inputs 0 V or VDD Slow MIN 1.6 2.4 Fast 3.8 5.6 3-V supply, No load, Clock running, All inputs 0 V or DVDD Slow 1.2 1.8 Fast 3.2 4.8 UNIT mA Power-down supply current (see Figure 13) 10 nA analog output dynamic performance PARAMETER SR Output slew rate TEST CONDITIONS TYP UNIT CL = 100 pF, RL = 10 kΩ, VO = 10% to 90%, Vref = 2.048 V, 1024 V Fast 5 V/µs Slow 1 V/µs 3 Output settling time To ±0.5 LSB, CL = 100 pF, RL = 10 kΩ, See Note 1 Fast ts Slow 9 1 Output settling time, code to code To ±0.5 LSB, CL = 100 pF, RL = 10 kΩ, See Note 2 Fast ts(c) Slow 2 Glitch energy Code transition from 7FF to 800 SNR Signal-to-noise ratio S/(N+D) Signal-to-noise + distortion THD Total harmonic distortion SFDR Spurious-free dynamic range Sine wave generated by DAC, Reference voltage = 1.024 at 3 V and 2.048 at 5 V, fs = 400 KSPS, fOUT = 1.1-kHz sine wave, CL = 100 pF, RL = 10 kΩ, BW = 20 kHz µss µss 10 nV-s 74 dB 66 dB −68 dB 70 dB NOTES: 1. Settling time is the time for the output signal to remain within ±0.5 LSB of the final measured value for a digital input code change of FFF hex to 080 hex for 080 hex to FFF hex. 2. Settling time is the time for the output signal to remain within ±0.5 LSB of the final measured value for a digital input code change of one count. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 electrical characteristics over recommended operating free-air temperature range, Vref = 2.048 V, AVDD = DVDD = 5 V and Vref = 1.024 V for AVDD = DVDD = 3 V (unless otherwise noted) (continued) digital input timing requirements MIN tsu(CS−FS) tsu(FS−CK) Setup time, CS low before FS↓ Setup time, FS low before first negative SCLK edge NOM MAX UNIT 10 ns 8 ns tsu(C16−FS) Setup time, sixteenth negative SCLK edge after FS low on which bit D0 is sampled before rising edge of FS 10 ns tsu(C16−CS) Setup time. The first positive SCLK edge after D0 is sampled before CS rising edge. If FS is used instead of the SCLK positive edge to update the DAC, then the setup time is between the FS rising edge and CS rising edge. 10 ns twH twL Pulse duration, SCLK high 25 ns Pulse duration, SCLK low 25 ns tsu(D) Setup time, data ready before SCLK falling edge 8 ns th(D) twH(FS) Hold time, data held valid after SCLK falling edge 5 ns Pulse duration, FS high 60 ns PARAMETER MEASUREMENT INFORMATION ÎÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ SCLK 1 2 tsu(D) DIN twH twL 3 4 5 15 16 th(D) D15 D14 D13 D12 tsu(FS-CK) D1 D0 tsu(C16-CS) tsu(CS-FS) CS twH(FS) tsu(C16-FS) FS Figure 2. Timing Diagram 8 ÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 TYPICAL CHARACTERISTICS LOAD REGULATION LOAD REGULATION 0.2 0.35 VDD = 3 V Vref = 1 V VO = Full Scale 0.18 0.16 0.30 0.25 VO − Output − V 0.14 VO − Output − V VDD = 5 V Vref = 2 V VO = Full Scale 3-V Slow Mode, Sink 0.12 0.10 3-V Fast Mode, Sink 0.08 0.06 5-V Slow Mode, Sink 0.20 5-V Fast Mode, Sink 0.15 0.10 0.04 0.05 0.02 0 0 0 0.01 0.02 0.05 0.1 0.2 0.5 0.8 1 2 0 Load Current − mA 0.02 0.04 0.1 0.2 0.4 0.8 Load Current − mA Figure 3 1 2 4 Figure 4 LOAD REGULATION LOAD REGULATION 4.01 2.0015 5-V Slow Mode, Source 3-V Slow Mode, Source 2.001 4.005 2.0005 VO − Output − V VO − Output − V 2.000 4 5-V Fast Mode, Source 3.995 3-V Fast Mode, Source 1.9995 1.999 1.9985 1.998 3.99 1.9975 VDD = 5 V Vref = 2 V VO = Full Scale 1.997 3.985 0 0.02 0.04 0.1 0.2 0.4 0.8 Load Current − mA 1 2 VDD = 3 V Vref = 1 V VO = Full Scale 4 1.9965 0 0.01 0.02 0.05 0.1 0.2 0.5 Load Current − mA Figure 5 0.8 1 2 Figure 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 TYPICAL CHARACTERISTICS SUPPLY CURRENT vs TEMPERATURE SUPPLY CURRENT vs TEMPERATURE 4 3.5 I DD − Supply Current − mA 3.5 I DD − Supply Current − mA 4 VDD = 3 V Vref = 1.024 V VO Full Scale (Worst Case for IDD) Fast Mode 3 2.5 2 1.5 1 3 −20 0 20 VDD = 5 V Vref = 1.024 V VO Full Scale (Worst Case for IDD) 2.5 2 1.5 Slow Mode 0.5 −40 Fast Mode Slow Mode 1 40 60 80 0.5 −40 100 −20 T − Temperature − °C Figure 7 100 TOTAL HARMONIC DISTORTION vs FREQUENCY 0 0 Vref = 1-V dc + 1-VPP Sine Wave Output Full Scale −10 THD − Total Harmonic Distortion − dB THD − Total Harmonic Distortion − dB 80 Figure 8 TOTAL HARMONIC DISTORTION vs FREQUENCY −20 −30 −−40 −50 −60 Fast Mode −70 −80 0 5 10 20 30 50 100 Vref = 1-V dc + 1-VPP Sine Wave Output Full Scale −10 −20 −30 −−40 −50 −60 Slow Mode −70 −80 0 5 f − Frequency − kHz 10 20 Figure 10 POST OFFICE BOX 655303 30 f − Frequency − kHz Figure 9 10 0 20 40 60 T − Temperature − °C • DALLAS, TEXAS 75265 50 100 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 TYPICAL CHARACTERISTICS Vref = 1-V dc + 1-VPP Sine Wave Output Full Scale −10 TOTAL HARMONIC DISTORTION AND NOISE vs FREQUENCY THD − Total Harmonic Distortion And Noise − dB 0 −20 −30 −−40 −50 Fast Mode −60 −70 −80 0 Vref = 1-V dc + 1-VPP Sine Wave, Output Full Scale −10 −20 −30 −−40 −50 Slow Mode −60 −70 −80 0 5 10 30 20 50 100 0 5 10 f − Frequency − kHz 20 30 50 100 f − Frequency − kHz Figure 11 Figure 12 SUPPLY CURRENT vs TIME (WHEN ENTERING POWER-DOWN MODE) 4000 3500 I DD − Supply Current − µ A THD − Total Harmonic Distortion And Noise − dB TOTAL HARMONIC DISTORTION AND NOISE vs FREQUENCY 3000 2500 2000 1500 1000 500 0 0 200 400 600 800 1000 t − Time − ns Figure 13 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 11 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 DNL − Differential Nonlinearity − LSB TYPICAL CHARACTERISTICS DIFFERENTIAL NONLINEARITY 0.3 0.25 0.2 0.15 0.1 0.05 0 −0.05 −0.1 −0.15 −0.2 −0.25 −0.3 VCC = 5 V, Vref = 2 V, SCLK = 1 MHz) 0 256 512 768 1024 1280 1536 1792 2048 2304 2560 2816 3072 3328 3584 3840 4096 Digital Code Figure 14 INL − Integral Nonlinearity − LSB INTEGRAL NONLINEARITY 1 VCC = 5 V, Vref = 2 V, SCLK = 1 MHz 0.5 0 −0.5 −1 −1.5 0 256 512 768 1024 1280 1536 1792 2048 2304 2560 2816 3072 3328 3584 3840 4096 Digital Code Figure 15 12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 APPLICATION INFORMATION general function The TLV5614 is a 12-bit single-supply DAC based on a resistor string architecture. The device consists of a serial interface, speed and power-down control logic, a reference input buffer, a resistor string, and a rail-to-rail output buffer. The output voltage (full scale determined by external reference) is given by: 2 REF CODE [V] 2n where REF is the reference voltage and CODE is the digital input value within the range of 010 to 2n−1, where n = 12 (bits). The 16-bit data word, consisting of control bits and the new DAC value, is illustrated in the data format section. A power-on reset initially resets the internal latches to a defined state (all bits zero). serial interface Explanation of data transfer: First, the device has to be enabled with CS set to low. Then, a falling edge of FS starts shifting the data bit per bit (starting with the MSB) to the internal register on the falling edges of SCLK. After 16 bits have been transferred or FS rises, the content of the shift register is moved to the DAC latch, which updates the voltage output to the new level. The serial interface of the TLV5614 can be used in two basic modes: D Four wire (with chip select) D Three wire (without chip select) Using chip select (four-wire mode), it is possible to have more than one device connected to the serial port of the data source (DSP or microcontroller). The interface is compatible with the TMS320 DSP family. Figure 16 shows an example with two TLV5614s connected directly to a TMS320 DSP. TLV5614 TLV5614 CS FS DIN SCLK CS FS DIN SCLK TMS320 DSP XF0 XF1 FSX DX CLKX Figure 16. TMS320E Interface TMS320 is a trademark of Texas Instruments. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 13 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 APPLICATION INFORMATION serial interface (continued) If there is no need to have more than one device on the serial bus, then CS can be tied low. Figure 17 shows an example of how to connect the TLV5614 to a TMS320, SPI, or Microwire port using only three pins. TMS320 DSP TLV5614 FSX SPI FS DIN DX CLKX TLV5614 FS DIN SS MOSI SCLK SCLK Microwire FS DIN I/O SO SK SCLK CS TLV5614 SCLK CS CS Figure 17. Three-Wire Interface Notes on SPI and Microwire: Before the controller starts the data transfer, the software has to generate a falling edge on the I/O pin connected to FS. If the word width is 8 bits (SPI and Microwire), two write operations must be performed to program the TLV5614. After the write operation(s), the DAC output is updated automatically on the next positive clock edge, following the sixteenth falling clock edge. serial clock frequency and update rate The maximum serial clock frequency is given by: f SCLKmax + t wH(min) 1 )t + 20 MHz wL(min) The maximum update rate is: f UPDATEmax + 1 ǒ wH(min) ) twL(min)Ǔ + 1.25 MHz 16 t Note that the maximum update rate is a theoretical value for the serial interface, since the settling time of the TLV5614 has to be considered also. data format The 16-bit data word for the TLV5614 consists of two parts: D Control bits D New DAC value D15 D14 D13 D12 A1 A0 PWR SPD X: Don’t care SPD: Speed control bit: PWR: Power control bit: 14 (D15 . . . D12) (D11 . . . D0) D11 1 → fast mode 1 → power down D10 D9 D8 D7 D6 D5 D4 New DAC value (12 bits) 0 → slow mode 0 → normal operation POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 D3 D2 D1 D0 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 APPLICATION INFORMATION data format (continued) In power-down mode, all amplifiers within the TLV5614 are disabled. A particular DAC (A, B, C, D) of the TLV5614 is selected by A1 and A0 within the input word. A1 A0 DAC 0 0 A 0 1 B 1 0 C 1 1 D TLV5614 interfaced to TMS320C203 DSP hardware interfacing Figure 18 shows an example of how to connect the TLV5614 to a TMS320C203 DSP. The serial port is configured in burst mode, with FSX generated by the TMS320C203 to provide the frame synchronization (FS) input to the TLV5614. Data is transmitted on the DX line, with the serial clock input on the CLKX line. The general-purpose input/output port bits, IO0 and IO1, are used to generate the chip select (CS) and DAC latch update (LDAC) inputs to the TLV5614. The active-low power down (PD) is pulled high all the time to ensure the DACs are enabled. TMS320C203 TLV5614 SDIN DX SCLK CLKX FSX FS I/O 0 CS I/O 1 LDAC VDD PD VOUTA VOUTB REF REFINAB VOUTC REFINCD VOUTD VSS Figure 18. TLV5614 Interfaced With TMS320C203 software The application example outputs a differential in-phase (sine) signal between the VOUTA and VOUTB pins, and its quadrature (cosine) signal as the differential signal between VOUTC and VOUTD. The on-chip timer is used to generate interrupts at a fixed frequency. The related interrupt service routine pulses LDAC low to update all four DACs simultaneously, then fetches and writes the next sample to all four DACs. The samples are stored in a look-up table, which describes two full periods of a sine wave. The synchronous serial port of the DSP is used in burst mode. In this mode, the processor generates an FS pulse preceding the MSB of every data word. If multiple, contiguous words are transmitted, a violation of the tsu(C16−FS) timing requirement occurs. To avoid this, the program waits until the transmission of the previous word has been completed. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 15 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 APPLICATION INFORMATION ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; Processor: TMS320C203 running at 40 MHz ; ; Description: ; ; This program generates a differential in−phase (sine) on (OUTA−OUTB) and it’s ; quadrature (cosine) as a differential signal on (OUTC−OUTD). ; ; The DAC codes for the signal samples are stored as a table of 64 12−bit values, ; describing 2 periods of a sine function. A rolling pointer is used to address the ; table location in the first period of this waveform, from which the DAC A samples ; are read. The samples for the other 3 DACs are read at an offset to this rolling ; pointer: ; DAC Function Offset from rolling pointer ; A sine 0 ; B inverse sine 16 ; C cosine 8 ; D inverse cosine24 ; ; The on−chip timer is used to generate interrupts at a fixed rate. The interrupt ; service routine first pulses LDAC low to update all DACs simultaneously ; with the values which were written to them in the previous interrupt. Then all ; 4 DAC values are fetched and written out through the synchronous serial interface ; Finally, the rolling pointer is incremented to address the next sample, ready for ; the next interrupt. ; ;  1998, Texas Instruments Inc. ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− I/O and memory mapped regs −−−−−−−−−−−−−−−−−−−−−−−−−−−−− .include ”regs.asm” ;−−−−−−−jump vectors −−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− .ps 0h b start b int1 b int23 b timer_isr; −−−−−−−−−−− variables −−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− temp .equ 0060h r_ptr .equ 0061h iosr_stat .equ 0062h DACa_ptr .equ 0063h DACb_ptr .equ 0064h DACc_ptr .equ 0065h DACd_ptr .equ 0066h ;−−−−−−−−−−−constants−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; DAC control bits to be OR’ed onto data ; all fast mode DACa_control .equ 01000h DACb_control .equ 05000h DACc_control .equ 09000h DACd_control .equ 0d000h ;−−−−−−−−−−− tables −−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− .ds 02000h sinevals .word 00800h .word 0097Ch .word 00AE9h .word 00C3Ah .word 00D61h .word 00E53h .word 00F07h .word 00F76h .word 00F9Ch .word 00F76h .word 00F07h .word 00E53h 16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 APPLICATION INFORMATION .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word .word 00D61h 00C3Ah 00AE9h 0097Ch 00800h 00684h 00517h 003C6h 0029Fh 001ADh 000F9h 0008Ah 00064h 0008Ah 000F9h 001ADh 0029Fh 003C6h 00517h 00684h 00800h 0097Ch 00AE9h 00C3Ah 00D61h 00E53h 00F07h 00F76h 00F9Ch 00F76h 00F07h 00E53h 00D61h 00C3Ah 00AE9h 0097Ch 00800h 00684h 00517h 003C6h 0029Fh 001ADh 000F9h 0008Ah 00064h 0008Ah 000F9h 001ADh 0029Fh 003C6h 00517h 00684h POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 17 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 APPLICATION INFORMATION ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; Main Program ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− .ps 1000h .entry start ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; disable interrupts ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− setc INTM ; disable maskable interrupts splk #0ffffh, IFR; clear all interrupts splk #0004h, IMR; timer interrupts unmasked ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; set up the timer ; timer period set by values in PRD and TDDR ; period = (CLKOUT1 period) x (1+PRD) x (1+TDDR) ; examples for TMS320C203 with 40MHz main clock ; Timer rate TDDR PRD ; 80 kHz 9 24 (18h) ; 50 kHz 9 39 (27h) ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− prd_val.equ 0018h tcr_val.equ 0029h splk #0000h, temp; clear timer out temp, TIM splk #prd_val, temp; set PRD out temp, PRD splk #tcr_val, temp; set TDDR, and TRB=1 for auto−reload out temp, TCR ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; Configure IO0/1 as outputs to be : ; IO0 CS − and set high ; IO1 LDAC − and set high ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− in temp, ASPCR; configure as output lacl temp or #0003h sacl temp out temp, ASPCR in temp, IOSR; set them high lacl temp or #0003h sacl temp out temp, IOSR ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; set up serial port for ; SSPCR.TXM=1 Transmit mode − generate FSX ; SSPCR.MCM=1 Clock mode − internal clock source ; SSPCR.FSM=1 Burst mode ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− splk #0000Eh, temp out temp, SSPCR; reset transmitter splk #0002Eh, temp out temp,SSPCR ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; reset the rolling pointer ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− lacl #000h sacl r_ptr ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; enable interrupts ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− clrc INTM ; enable maskable interrupts ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; loop forever! ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− 18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 APPLICATION INFORMATION next idle ;wait for interrupt b next ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; all else fails stop here ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− done b done ;hang there ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; Interrupt Service Routines ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− int1 ret ; do nothing and return int23 ret ; do nothing and return timer_isr: in iosr_stat, IOSR; store IOSR value into variable space lacl iosr_stat ; load acc with iosr status and #0FFFDh ; reset IO1 − LDAC low sacl temp ; out temp, IOSR ; or #0002h ; set IO1 − LDAC high sacl temp ; out temp, IOSR ; and #0FFFEh ; reset IO0 − CS low sacl temp ; out temp, IOSR ; lacl r_ptr ; load rolling pointer to accumulator add #sinevals ; add pointer to table start sacl DACa_ptr ; to get a pointer for next DAC a sample add #08h ; add 8 to get to DAC C pointer sacl DACc_ptr add #08h ; add 8 to get to DAC B pointer sacl DACb_ptr add #08h ; add 8 to get to DAC D pointer sacl DACd_ptr mar *,ar0 ; set ar0 as current AR ; DAC A lar ar0, DACa_ptr ; ar0 points to DAC a sample lacl * ; get DAC a sample into accumulator or #DACa_control ; OR in DAC A control bits sacl temp ; out temp, SDTR ; send data ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; We must wait for transmission to complete before writing next word to the SDTR.; TLV5614/04 interface does not allow the use of burst mode with the full packet; rate, as we need a CLKX −ve edge to clock in last bit before FS goes high again,; to allow SPI compatibility. ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− rpt #016h ; wait long enough for this configuration nop ; of MCLK/CLKOUT1 rate ; DAC lar lacl or sacl out rpt nop ; DAC C lar lacl or sacl out rpt nop B ar0, dacb_ptr ; * ; #DACb_control ; temp ; temp, SDTR ; #016h ; ; ar0, dacc_ptr ; * ; #DACc_control ; temp ; temp, SDTR; #016h ; ; ar0 points to DAC a sample get DAC a sample into accumulator OR in DAC B control bits send data wait long enough for this configuration of MCLK/CLKOUT1 rate ar0 points to dac a sample get DAC a sample into accumulator OR in DAC C control bits send data wait long enough for this configuration of MCLK/CLKOUT1 rate POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 19 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 APPLICATION INFORMATION ; DAC D lar lacl or sacl out lacl add and sacl rpt nop ar0, dacd_ptr; ar0 points to DAC a sample * ; get DAC a sample into accumulator #dacd_control ; OR in DAC D control bits temp ; temp, SDTR ; send data r_ptr #1h #001Fh r_ptr #016h ; ; ; ; ; ; ; now take CS high again lacl iosr_stat ; or #0001h ; sacl temp ; out temp, IOSR ; clrc intm ; ret ; .end 20 load rolling pointer to accumulator increment rolling pointer count 0−31 then wrap back round store rolling pointer wait long enough for this configuration of MCLK/CLKOUT1 rate load acc with iosr status set IO0 − CS high re-enable interrupts return from interrupt POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 APPLICATION INFORMATION TLV5614 interfaced to MCS51 microcontroller hardware interfacing Figure 19 shows an example of how to connect the TLV5614 to an MCS51 Microcontroller. The serial DAC input data and external control signals are sent via I/O port 3 of the controller. The serial data is sent on the RxD line, with the serial clock output on the TxD line. Port 3 bits 3, 4, and 5 are configured as outputs to provide the DAC latch update (LDAC), chip select (CS) and frame sync (FS) signals for the TLV5614. The active low power down pin (PD) of the TLV5614 is pulled high to ensure that the DACs are enabled. MCS®51 TLV5614 RxD SDIN TxD SCLK P3.3 LDAC P3.4 CS P3.4 FS VDD PD VOUTA VOUTB REF REFINAB VOUTC REFINCD VOUTD VSS Figure 19. TLV5614 Interfaced With MCS51 software The example is the same as for the TMS320C203 in this data sheet, but adapted for a MCS51 controller. It generates a differential in-phase (sine) signal between the VOUTA and VOUTB pins, and its quadrature (cosine) signal is the differential signal between VOUTC and VOUTD. The on-chip timer is used to generate interrupts at a fixed frequency. The related interrupt service routine pulses LDAC low to update all four DACs simultaneously, then fetches and writes the next sample to all four DACs. The samples are stored as a look-up table, which describes one full period of a sine wave. The serial port of the controller is used in Mode 0, which transmits 8 bits of data on RxD, accompanied by a synchronous clock on TxD. Two writes, concatenated together, are required to write a complete word to the TLV5614. The CS and FS signals are provided in the required fashion through control of IO port 3, which has bit addressable outputs. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 21 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 APPLICATION INFORMATION ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; Processor: 80C51 ; ; Description: ; ; This program generates a differential in-phase (sine) on (OUTA−OUTB) ; and it’s quadrature (cosine) as a differential signal on (OUTC−OUTD). ; ;  1998, Texas Instruments Inc. ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− NAME GENIQ MAIN SEGMENT CODE ISR SEGMENT CODE SINTBL SEGMENT CODE VAR1 SEGMENT DATA STACK SEGMENT IDATA ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; Code start at address 0, jump to start ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− CSEG AT 0 LJMP start ; Execution starts at address 0 on power−up. ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; Code in the timer0 interrupt vector ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− CSEG AT 0BH LJMP timer0isr ; Jump vector for timer 0 interrupt is 000Bh ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; Global variables need space allocated ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− RSEG VAR1 temp_ptr: DS 1 rolling_ptr: DS 1 ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−; Interrupt service routine for timer 0 interrupts ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− RSEG ISR timer0isr: PUSH PSW PUSH ACC CLR INT1 ; pulse LDAC low SETB INT1 ; to latch all 4 previous values at the same time ; 1st thing done in timer isr => fixed period CLR T0 ; set CS low ; ; ; ; ; ; The signal to be output on each DAC is a sine function. One cycle of a sine wave is held in a table @ sinevals as 32 samples of msb, lsb pairs (64 bytes). We have ; one pointer which rolls round this table, rolling_ptr, incrementing by 2 bytes (1 sample) on each interrupt (at the end of this routine). ; The ; DAC ; A ; B ; C ; D MOV MOV MOV MOVC 22 DAC samples are read at an offset to this rolling pointer: Function Offset from rolling_ptr sine 0 inverse sine 32 cosine 16 inverse cosine48 DPTR,#sinevals; set DPTR to the start of the table ; of sine signal values R7,rolling_ptr; R7 holds the pointer ;into the sine table A,R7 A,@A+DPTR ; get DAC A msb ; msb of DAC A is in the ACC POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 APPLICATION INFORMATION CLR MOV T1 SBUF,A INC R7 MOV A,R7 MOVC A,@A+DPTR A_MSB_TX: JNB TI,A_MSB_TX CLR TI MOV SBUF,A ; transmit it − set FS low ; send it out the serial port ; increment the pointer in R7 ; to get the next byte from the table ; which is the lsb of this sample, now in ACC ; wait for transmit to complete ; clear for new transmit ; and send out the lsb of DAC A ; DAC C next ; DAC C codes should be taken from 16 bytes (8 samples) further on ; in the sine table − this gives a cosine function MOV A,R7 ; pointer in R7 ADD A,#0FH ; add 15 − already done one INC ANL A,#03FH ; wrap back round to 0 if > 64 MOV R7,A ; pointer back in R7 MOVC ORL A_LSB_TX: JNB SETB CLR T1 CLR MOV INC MOV MOVC C_MSB_TX: JNB CLR MOV A,@A+DPTR A,#01H ; get DAC C msb from the table ; set control bits to DAC C address TI,A_LSB_TX T1 ; wait for DAC A lsb transmit to complete ; toggle FS TI SBUF,A R7 A,R7 A,@A+DPTR ; ; ; ; ; TI,C_MSB_TX TI SBUF,A ; wait for transmit to complete ; clear for new transmit ; and send out the lsb of DAC C clear for new transmit and send out the msb of DAC C increment the pointer in R7 to get the next byte from the table which is the lsb of this sample, now in ACC ; DAC B next ; DAC B codes should be taken from 16 bytes (8 samples) further on ; in the sine table − this gives an inverted sine function MOV A,R7 ; pointer in R7 ADD A,#0FH ; add 15 − already done one INC ANL A,#03FH ; wrap back round to 0 if > 64 MOV R7,A ; pointer back in R7 MOVC ORL C_LSB_TX: JNB SETB CLR CLR MOV ; get INC MOV MOVC A,@A+DPTR A,#02H ; get DAC B msb from the table ; set control bits to DAC B address TI,C_LSB_TX T1 T1 TI SBUF,A ; wait for DAC C lsb transmit to complete ; toggle FS DAC B LSB R7 A,R7 A,@A+DPTR B_MSB_TX: JNB TI,B_MSB_TX CLR TI MOV SBUF,A ; clear for new transmit ; and send out the msb of DAC B ; increment the pointer in R7 ; to get the next byte from the table ; which is the lsb of this sample, now in ACC ; wait for transmit to complete ; clear for new transmit ; and send out the lsb of DAC B ; DAC D next ; DAC D codes should be taken from 16 bytes (8 samples) further on ; in the sine table − this gives an inverted cosine function POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 23 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 APPLICATION INFORMATION MOV ADD ANL MOV MOVC ORL A,R7 A,#0FH A,#03FH R7,A A,@A+DPTR A,#03H ; ; ; ; ; ; B_LSB_TX: JNB TI,B_LSB_TX ; SETB T1 ; CLR T1 CLR TI ; clear for MOV SBUF,A ; INC MOV MOVC D_MSB_TX: JNB CLR MOV pointer in R7 add 15 − already done one INC wrap back round to 0 if > 64 pointer back in R7 get DAC D msb from the table set control bits to DAC D address wait for DAC B lsb transmit to complete toggle FS new transmit and send out the msb of DAC D R7 A,R7 A,@A+DPTR ; increment the pointer in R7 ; to get the next byte from the table ; which is the lsb of this sample, now in ACC TI,D_MSB_TX TI SBUF,A ; wait for transmit to complete ; clear for new transmit ; and send out the lsb of DAC D ; increment the rolling pointer to point to the next sample ; ready for the next interrupt MOV A,rolling_ptr ADD A,#02H ; add 2 to the rolling pointer ANL A,#03FH ; wrap back round to 0 if > 64 MOV rolling_ptr,A ; store in memory again D_LSB_TX: JNB TI,D_LSB_TX ; wait for DAC D lsb transmit to complete CLR TI ; clear for next transmit SETB T1 ; FS high SETB T0 ; CS high POP ACC POP PSW RETI ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; Stack needs definition ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− RSEG STACK DS 10h ; 16 Byte Stack! ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; Main program code ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− RSEG MAIN start: MOV SP,#STACK−1 ; first set Stack Pointer CLR A MOV SCON,A ; set serial port 0 to mode 0 MOV TMOD,#02H ; set timer 0 to mode 2 − auto−reload MOV TH0,#038H ; set TH0 for 5kHs interrupts SETB INT1 ; set LDAC = 1 SETB T1 ; set FS = 1 SETB T0 ; set CS = 1 SETB ET0 ; enable timer 0 interrupts SETB EA ; enable all interrupts MOV rolling_ptr,A ; set rolling pointer to 0 SETB TR0 ; start timer 0 always: SJMP always ; while(1) ! RET ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− ; Table of 32 sine wave samples used as DAC data ;−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−− RSEG SINTBL 24 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 
  
  
µ   

  
 
    SGLS355 − JUNE 2006 APPLICATION INFORMATION sinevals: DW 01000H DW 0903EH DW 05097H DW 0305CH DW 0B086H DW 070CAH DW 0F0E0H DW 0F06EH DW 0F039H DW 0F06EH DW 0F0E0H DW 070CAH DW 0B086H DW 0305CH DW 05097H DW 0903EH DW 01000H DW 06021H DW 0A0E8H DW 0C063H DW 040F9H DW 080B5H DW 0009FH DW 00051H DW 00026H DW 00051H DW 0009FH DW 080B5H DW 040F9H DW 0C063H DW 0A0E8H DW 06021H END POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 25 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) TLV5614MPWREP ACTIVE TSSOP PW 16 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -55 to 125 5614EP V62/06602-01XE ACTIVE TSSOP PW 16 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -55 to 125 5614EP (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of