Order
Now
Product
Folder
Technical
Documents
Support &
Community
Tools &
Software
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
TPS25810 USB Type-C DFP Controller and Power Switch with Load Detection
1 Features
3 Description
•
•
•
•
•
•
•
•
•
The TPS25810 is a USB Type-C Downstream Facing
Port (DFP) controller with an integrated 3-A rated
USB power switch. The TPS25810 monitors the
Type-C Configuration Channel (CC) lines to
determine when an USB device is attached. If an
Upstream Facing Port (UFP) device is attached, the
TPS25810 applies power to VBUS and communicates
the selectable VBUS current sourcing capability to the
UFP via the passthrough CC line. If the UFP is
attached using an electronically marked cable, the
TPS25810 also applies VCONN power to the cable CC
pin. The TPS25810 also identifies when Type-C
audio or debug accessories are attached.
1
•
•
•
•
•
•
USB Type-C Rev. 1.2 Compliant DFP Controller
Connector Attach/Detach Detection
STD/1.5-A/3-A Capability Advertisement on CC
Super Speed Polarity Determination
VBUS Application and Discharge
VCONN Application to Electronically Marked Cable
Audio and Debug Accessory Identification
0.7-µA (typ) IDDQ When Port Unattached
Three Input Supply Options
– IN1: USB Charging Supply
– IN2: VCONN Supply
– AUX: Device Power Supply
Power Wake Supports Low Power in System
Hibernate (S4) and OFF (S5) Power States
34-mΩ (typ) High-Side MOSFET
1.7/3.4-A ILimit (±7.1%) - Programmable
Port Power Management Enables Power
Resource Optimization Across Multi-Ports
Package: 20-Pin WQFN (3 x 4) (1)
UL Listed – File No. E169910
The TPS25810 draws less than 0.7 uA (typ) when no
device is attached. Additional system power saving is
achievable in S4/S5 system power states by using
the UFP output to disable the high power 5-V supply
when no UFP is attached. In this mode the device is
capable of running from an auxiliary supply (AUX)
which can be a lower voltage supply (3.3 V), typically
powering the system uC in low power states (S4/S5).
The TPS25810 34-mΩ power switch has two
selectable fixed current limits that align with the TypeC current levels. The FAULT output signals when the
switch is in an over current or over temperature
condition. The LD_DET output controls power
management to multiple high current Type-C ports in
an environment where all ports cannot simultaneously
provide high current (3 A).
2 Applications
•
•
•
(1)
USB Type C Host Port in Notebook for Sleep
Charging
LCD Monitor/Docking Station and Charging
Cradles
Type C USB Wall Chargers
Device Information(1)
PART NUMBER
TPS25810
PACKAGE
WQFN (20)
BODY SIZE (NOM)
3.00 mm x 4.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
CC pins are IEC-61000-4-2 rated
Simplified Schematic
6 x 100 NŸ
(optional )
4.5 V ± 6.5V
CC Power
4.5 V ± 5.5V
Auxiliary Power
2.9 V ± 5.5V
TPS25810
IN1
OUT
IN2
FAULT
AUX
LD_ DET
VBUS
Power Switch
Status Signals
CC1
120PF
USB Type-C
Connector
Bus Power
CC2
EN
Control Signals
CHG
CHG_HI
REF
100 NŸ
(1%)
UFP
POL
AUDIO
DEBUG
REF_ RTN GND Power Pad
Type- C DFP
Status Signals
6.8 PF
Copyright
Copyright©
©2016,
2016,Texas
TexasInstruments
InstrumentsIncorporated
Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
4
4
4
5
5
7
9
Absolute Maximum Ratings ......................................
ESD Ratings ............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Switching Characteristics ..........................................
Typical Characteristics ..............................................
Detailed Description ............................................ 11
7.1 Overview ................................................................. 11
7.2 Functional Block Diagram ....................................... 13
7.3 Feature Description................................................. 13
7.4 Device Functional Modes........................................ 21
8
Application and Implementation ........................ 22
8.1 Application Information............................................ 22
8.2 Typical Applications ................................................ 22
9 Power Supply Recommendations...................... 27
10 Layout................................................................... 28
10.1 Layout Guidelines ................................................. 28
10.2 Layout Example .................................................... 29
11 Device and Documentation Support ................. 30
11.1
11.2
11.3
11.4
11.5
11.6
11.7
Device Support ....................................................
Documentation Support .......................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
30
30
30
30
30
30
30
12 Mechanical, Packaging, and Orderable
Information ........................................................... 30
4 Revision History
Changes from Revision B (May 2016) to Revision C
Page
•
Changed Feature From: USB Type-C Rev. 1.1 Compliant DFP Controller To: USB Type-C Rev. 1.2 Compliant DFP
Controller ............................................................................................................................................................................... 1
•
Changed text From: Type-C spec revision 1.1 To: Type-C spec revision 1.2 in the Overview section ............................... 11
•
Replaced Figure 15 ............................................................................................................................................................. 18
Changes from Revision A (September 2015) to Revision B
Page
•
Added CC pins IEC-61000-4-2 rated footnote ....................................................................................................................... 1
•
Changed from UL and CB Tests Underway to UL Listed – File No. E169910 in Features ................................................... 1
•
Changed 10µF to 6.8µF in Simplified Schematic ................................................................................................................... 1
•
Added text to REF description ............................................................................................................................................... 3
•
Added IEC information to ESD Ratings ................................................................................................................................. 4
•
Changed IN2 II parameter description in Electrical Characteristics ...................................................................................... 7
•
Changed tres to tios in Switching Characteristics .................................................................................................................... 8
•
Added text to Detecting a Connection section .................................................................................................................... 12
•
Changed Rp to Rds in Figure 12 ......................................................................................................................................... 12
•
Changed loss to drop in Figure 14 ...................................................................................................................................... 16
•
Added text and Figure 15 to Plug Polarity Detection ........................................................................................................... 18
•
Added last sentence to Input and Output Capacitance ....................................................................................................... 23
•
Added ESD Considerations to Layout Guidelines................................................................................................................ 28
•
Added Protecting the TPS25810 from High Voltage DFPs to Related Documentation ....................................................... 30
Changes from Original (September 2015) to Revision A
•
2
Page
Changed from Product Preview to Production Data............................................................................................................... 1
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
5 Pin Configuration and Functions
FAULT
LD_DET
UFP
POL
AUDIO
RVC Package
20-Pin WQFN
Top View
20
19
18
17
1
Thermal
Pad
16
DEBUG
15
OUT
14
OUT
IN2
4
13
CC2
AUX
5
12
GND
EN
6
11
CC1
7
8
9
10
REF
3
REF_RTN
IN1
CHG_HI
2
CHG
IN1
Pin Functions
PIN
I/O
DESCRIPTION
NAME
NUMBER
FAULT
1
O
Fault event indicator. Open-drain logic output that asserts low to indicate current limit or thermal shutdown event
due to over temperature.
IN1
2, 3
I
VBUS input supply. Internal power switch connects IN1 to OUT.
IN2
4
I
VCONN input supply. Internal power switch connects IN2 to CC1 or CC2. Short to IN1 if only one supply is used.
AUX
5
I
Auxiliary input supply. Connect to always alive system rail to use the Power Wake feature. Short to IN1 and IN2 if
only one supply is used.
EN
6
I
Enable logic input to turn the device on and off.
CHG
7
I
Charge logic input to select between standard USB (500 mA for a Type C receptacle supporting only USB 2.0 and
900 mA for Type C receptacle supporting USB 3.1) or Type-C current sourcing ability.
CHG_HI
8
I
High-charge logic input to select between 1.5-A and 3-A Type-C current sourcing capability. Valid when CHG is
set to Type-C current.
REF_RTN
9
I
Precision signal reference return. Connect to REF pin via 100-kΩ, 1% resistor.
REF
10
I
Analog input used to generate internal current reference. Connect a 1% or better, 100 ppm, 100-kΩ resistor
between this pin and REF_RTN.
CC1
11
I/O
GND
12
–
Analog input/output that connects to the Type-C receptacle CC1 pin
CC2
13
I/O
Analog input/output that connects to the Type-C receptacle CC2 pin.
Power ground
OUT
14,15
O
Power switch output.
DEBUG
16
O
Open-drain logic output that asserts when a Type-C Debug accessory is identified on the CC lines.
AUDIO
17
O
Open-drain logic output that asserts when a Type-C Audio accessory is identified on the CC lines.
POL
18
O
Polarity open-drain logic output that signals which Type-C CC pin is connected to the CC line. This gives the
information needed to mux the super speed lines. Asserted when the CC2 pin is connected to the CC line in
cable.
UFP
19
O
Open-drain logic output that asserts when a Type-C UFP is identified on the CC lines.
LD_DET
20
O
Load-detect open-drain logic output that signals when a device set to source Type-C 3 A current is sourcing over
1.95 A nominal.
Thermal Pad
–
–
Thermal pad on bottom of package.
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
3
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range, voltages are respect to GND (unless otherwise noted)
(1)
MIN
MAX
UNIT
–0.3
7
V
REF_RTN
Internally
connected
to GND
V
OUT, REF, CC1, CC2
Internally
limited
A
5
A
IN1, IN2, AUX, EN, CHG, CHG_HI, REF, OUT, LD_DET,
FAULT, CC1, CC2, UFP, POL, AUDIO, DEBUG
Pin voltage, V
Pin positive source current, ISRC
OUT (while applying VBUS)
CC1, CC2 (while applying VCONN)
Pin positive sink current, ISNK
LD_DET, FAULT, UFP, POL, AUDIO, DEBUG
1
A
Internally
limited
mA
Operating junction temperature, TJ
–40
180
°C
Storage temperature range, Tstg
–65
150
°C
(1)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
VALUE
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (2)
V(ESD) (1)
(1)
(2)
(3)
(4)
Electrostatic
discharge
Charged-device model (CDM), per JEDEC specification JESD22-C101 (3)
IEC (4)
UNIT
±2000
±500
V
IEC61000-4-2 contact discharge, CC1 and CC2
±8000
IEC61000-4-2 air discharge, CC1 and CC2
±15000
Electrostatic discharge (ESD) to measure device sensitivity/immunity to damage caused by assembly line electrostatic discharges into
the device.
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Surges per IEC61000-402, 1999 applied between CC1/CC2 and output ground of the TPS25810EVM-745.
6.3 Recommended Operating Conditions
Voltages are with respect to GND (unless otherwise noted)
MIN
VI
Supply voltage
NOM
MAX
IN1
4.5
6.5
IN2
4.5
5.5
AUX
2.9
5.5
5.5
VI
Input voltage
EN, CHG, CHG_HI
0
VIH
High-level input voltage
EN, CHG, CHG_HI
1.17
VIL
Low-level voltage
EN, CHG, CHG_HI
VPU
Pull-up voltage
Used on LD_DET, FAULT, UFP, POL, AUDIO,
DEBUG
ISRC
Positive source current
ISNK
Positive sink current (10 ms moving
average)
UNIT
V
V
V
0
OUT
0.63
V
5.5
V
3
A
250
mA
LD_DET, FAULT, UFP, POL, AUDIO, DEBUG
10
mA
ISNK_PULSE Positive repetitive pulse sink current LD_DET, FAULT, UFP, POL, AUDIO, DEBUG
Internally
Limited
mA
102
kΩ
125
°C
RREF
Reference Resistor
TJ
Operating junction temperature
4
CC1 or CC2 when supplying VCONN
98
–40
Submit Documentation Feedback
100
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
6.4 Thermal Information
TPS25810
THERMAL METRIC (1)
RVC (WQFN)
UNIT
20 PINS
RθJA
Junction-to-ambient thermal resistance
39.3
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
43.4
°C/W
RθJB
Junction-to-board thermal resistance
13
°C/W
ψJT
Junction-to-top characterization parameter
0.7
°C/W
ψJB
Junction-to-board characterization parameter
13
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
4.2
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Electrical Characteristics
–40°C ≤ TJ ≤ 125°C, 4.5 V ≤ VIN1 ≤ 6.5 V, 4.5 V ≤ VIN2 ≤ 5.5 V, 2.9 V ≤ VAUX ≤ 5.5 V; VEN = VCHG = VCHG_HI = VAUX, RREF = 100
kΩ. Typical values are at 25°C. All voltages are with respect to GND. IOUT and IOS defined positive out of the indicated pin
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
TJ = 25°C, IOUT = 3 A
34
37
–40°C ≤ TJ ≤ 85°C, IOUT = 3 A
34
46
–40°C ≤ TJ ≤ 125°C, IOUT = 3 A
34
55
VOUT = 6.5 V, VIN1 = VEN = 0 V,
OUT to IN reverse leakage current –40°C ≤ TJ ≤ 85°C,
IREV is current out of IN1 pin
0
3
UNIT
OUT - POWER SWITCH
RDS(on)
IREV
On resistance (1)
mΩ
µA
OUT - CURRENT LIMIT
IOS
Short circuit current limit
(1)
VCHG = 0 V or VCHG = VAUX and VCHG_HI = 0
V
1.58
1.7
1.82
VCHG = VAUX and VCHG_HI = VAUX
3.16
3.4
3.64
RREF = 10 Ω
A
7
OUT - DISCHARGE
Discharge resistance
VOUT = 4 V, UFP signature removed from
CC lines, time < tw_DCHG
400
500
600
Ω
Bleed discharge resistance
VOUT = 4 V, No UFP signature on CC lines,
time > tw_DCHG
100
150
250
kΩ
0.78
0.8
0.82
V
15.3
µA
REF
VO
Output voltage
IOS
Short circuit current
RREF = 10 Ω
VOL
Output low voltage
IFAULT = 1 mA
350
mV
IOFF
Off-state leakage
VFAULT = 5.5 V
1
µA
VOL
Output low voltage
ILD_DET = 1 mA
350
mV
IOFF
Off-state leakage
VLD_DET = 5.5 V
1
µA
ITH
OUT sourcing, rising threshold
current for load detect
2.1
A
9.5
FAULT
LD_DET
Hysteresis
(1)
(2)
1.8
(2)
1.95
125
mA
Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account
separately.
These parameters are provided for reference only and do not constitute part of TI’s published specifications for purposes of TI’s product
warranty.
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
5
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
Electrical Characteristics (continued)
–40°C ≤ TJ ≤ 125°C, 4.5 V ≤ VIN1 ≤ 6.5 V, 4.5 V ≤ VIN2 ≤ 5.5 V, 2.9 V ≤ VAUX ≤ 5.5 V; VEN = VCHG = VCHG_HI = VAUX, RREF = 100
kΩ. Typical values are at 25°C. All voltages are with respect to GND. IOUT and IOS defined positive out of the indicated pin
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
TJ = 25°C, IOUT = 250 mA
365
420
-40°C ≤ TJ ≤ 85°C, IOUT = 250 mA
365
530
-40°C ≤ TJ ≤ 125°C, IOUT = 250 mA
365
600
355
410
UNIT
CC1/CC2 - VCONN POWER SWITCH
RDS(on)
On resistance
mΩ
CC1/CC2 - VCONN POWER SWITCH - CURRENT LIMIT
300
Short circuit current limit (1)
IOS
RREF = 10 Ω
800
mA
CC1/CC2 – CONNECT MANAGEMENT – DANGLING ELECTRONICALLY MARKED CABLE MODE
ISRC
Sourcing current on the passthrough CC Line
0 V ≤ VCCx ≤ 1.5 V
64
80
96
µA
Sourcing current on the Ra CC
line
0 V ≤ VCCx ≤ 1.5 V
64
80
96
µA
64
80
96
µA
CC1/CC2 – CONNECT MANAGEMENT – ACCESSORY MODE
CCx Sourcing current
(CC2- Audio, CC1-Debug)
ISRC
CCx Sourcing current
(CC1- Audio, CC2-Debug)
0 V ≤ VCCx ≤ 1.5 V
(2)
0 V ≤ VCCx ≤ 1.5 V
0
µA
CC1/CC2 – CONNECT MANAGEMENT – UFP MODE
Sourcing current with either IN1 or 0 V ≤ VCCx ≤ 1.5 V
IN2 in UVLO
VIN1 < VTH_UVLO_IN1 or VIN2 < VTH_UVLO_IN2
ISRC
64
80
96
75
80
85
VCHG = VAUX and VCHG_HI = 0 V
0 V ≤ VCCx ≤ 1.5 V
170
180
190
VCHG = VAUX and VCHG_HI = VAUX
0 V ≤ VCCx ≤ 2.45 V
312
330
348
VCHG = 0 V and VCHG_HI = 0 V
0 V ≤ VCCx ≤ 1.5 V
ISRC
Sourcing current
µA
µA
UFP, POL, AUDIO, DEBUG
VOL
Output low voltage
ISNK_PIN = 1 mA
IOFF
Off-state leakage
VPIN = 5.5 V
250
mV
1
µA
1.15
V
EN, CHG, CHG_HI - LOGIC INPUTS
VTH
Rising threshold voltage
VTH
Falling threshold voltage
0.925
0.65
Hysteresis (2)
IIN
Input current
0.875
V
50
VEN = 0 V or 6.5 V
–0.5
mV
0.5
µA
OVER TEMPERATURE SHUT DOWN
TTH_OTSD2
Rising threshold temperature for
device shutdown
155
Hysteresis (2)
TTH_OTSD1
°C
20
Rising threshold temperature for
OUT/ VCONN switch shutdown in
current limit
°C
135
Hysteresis (2)
°C
20
°C
IN1
VTH_UVLO_IN1
Rising threshold voltage for UVLO
3.9
Hysteresis (2)
6
4.1
100
Submit Documentation Feedback
4.3
V
mV
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
Electrical Characteristics (continued)
–40°C ≤ TJ ≤ 125°C, 4.5 V ≤ VIN1 ≤ 6.5 V, 4.5 V ≤ VIN2 ≤ 5.5 V, 2.9 V ≤ VAUX ≤ 5.5 V; VEN = VCHG = VCHG_HI = VAUX, RREF = 100
kΩ. Typical values are at 25°C. All voltages are with respect to GND. IOUT and IOS defined positive out of the indicated pin
(unless otherwise noted)
PARAMETER
II
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Disabled supply current
VEN = 0 V, -40°C ≤ TJ ≤ 85°C
1
µA
Enabled supply current with CC
lines open
-40°C ≤ TJ ≤ 85°C
1
µA
2
µA
Enabled supply current with
accessory or dangling
electronically marked cable
signature on CC lines
Enabled supply current with UFP
attached
VCHG = 0 V, or VCHG = VAUX and VCHG_HI =
0V
75
100
85
110
4.1
4.3
µA
IN2
VTH_UVLO_IN2
Rising threshold voltage for UVLO
3.9
Hysteresis (2)
II
V
100
mV
Disabled supply current
VEN = 0 V, -40°C ≤ TJ ≤ 85°C
1
µA
Enabled supply current with CC
lines open
-40°C ≤ TJ ≤ 85°C
1
µA
2
µA
II
Enabled supply current with
accessory or dangling
electronically marked cable
signature on CC lines
II
Enabled supply current with UFP
signature on CC lines
(Includes IN current that provides
the CC output current to the UFP
Rd resistor)
VCHG = 0 V, 0 V ≤ VCCx ≤ 1.5 V
98
110
VCHG = VIN and VCHG_HI = 0 V, 0 V ≤ VCCx ≤
1.5 V
198
215
0 V ≤ VCCx ≤ 2.45 V
348
373
2.75
2.85
µA
AUX
VTH_UVLO_AUX Rising threshold voltage for UVLO
Hysteresis
2.65
(2)
V
100
II
Disabled supply current
VEN = 0 V, -40°C ≤ TJ ≤ 85°C
II
Enabled internal supply current
with CC lines open
-40°C ≤ TJ ≤ 85°C
II
Enabled supply current with
accessory or dangling active cable
signature on CC lines
II
Enabled supply current with UFP
termination on CC lines and with
either IN1 or IN2 in UVLO
II
Enabled supply current with UFP
termination on CC lines
VIN1 < VTH_UVLO_IN1 or VIN2 < VTH_UVLO_IN2
mV
1
µA
0.7
3
µA
140
185
µA
145
190
µA
55
82
µA
6.6 Switching Characteristics
–40°C ≤ TJ ≤ 125°C, 4.5 V ≤ VIN1 ≤ 6.5 V, 4.5 V ≤ VIN2 ≤ 5.5 V, 2.9 V ≤ VAUX ≤ 5.5 V; VEN = VCHG = VCHG_HI = VAUX, RREF = 100
kΩ. Typical values are at 25°C. All voltages are with respect to GND. IOUT and IOS defined positive out of the indicated pin
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VIN1 = 5 V, CL = 1 µF, RL = 100 Ω
(measured from 10% to 90% of final
value)
1.2
1.8
2.5
ms
0.35
0.55
0.75
ms
2.5
3.5
5
ms
2
3
4.5
ms
OUT - POWER SWITCH
tr
Output voltage rise time
tf
Output voltage fall time
ton
Output voltage turn-on time
toff
Output voltage turn-off time
VIN1 = 5 V, CL = 1 µF, RL = 100 Ω
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
7
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
Switching Characteristics (continued)
–40°C ≤ TJ ≤ 125°C, 4.5 V ≤ VIN1 ≤ 6.5 V, 4.5 V ≤ VIN2 ≤ 5.5 V, 2.9 V ≤ VAUX ≤ 5.5 V; VEN = VCHG = VCHG_HI = VAUX, RREF = 100
kΩ. Typical values are at 25°C. All voltages are with respect to GND. IOUT and IOS defined positive out of the indicated pin
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
1.5
4
µs
8.2
10.7
ms
OUT - CURRENT LIMIT
Current limit response time to short
circuit
tios
VIN1 - VOUT = 1 V, RL = 10 mΩ, see
Figure 1
FAULT
tDEGA
Asserting deglitch due to over
current
tDEGA
Asserting deglitch due to over
temperature in current limit (1)
tDEGD
De-asserting deglitch
5.5
0
5.5
8.2
ms
10.7
ms
LD_DET
tDEGA
Asserting deglitch
tDEGD
De-asserting deglitch
45
65
85
ms
1.45
2.15
2.9
s
39
65
96
ms
0.15
0.25
0.35
ms
0.18
0.22
0.26
ms
1
1.5
2
ms
0.3
0.4
0.55
ms
1
3
µs
OUT - DISCHARGE
VOUT = 1 V, time ISNK_OUT > 1 mA
after UFP signature removed from
CC lines
RDCHG discharge time
CC1/CC2 - VCONN POWER SWITCH
tr
Output voltage rise time
tf
Output voltage fall time
ton
Output voltage turn-on time
toff
Output voltage turn-off time
VIN2 = 5 V, CL = 1 µF, RL = 100 Ω
(measured from 10% to 90% of final
value)
VIN2 = 5 V, CL = 1 µF, RL = 100 Ω
CC1/CC2 - VCONN POWER SWITCH - CURRENT LIMIT
Current limit response time to short
circuit
tres
VIN2 – VCONN = 1 V, R = 10 mΩ, see
Figure 1
UFP, POL, AUDIO, DEBUG
tDEGR
Asserting deglitch
100
150
200
ms
tDEGF
De-asserting deglitch
7.9
12.5
17.7
ms
(1)
These parameters are provided for reference only and do not constitute part of TI’s published specifications for purposes of TI’s product
warranty.
IOS
IOUT
tios
Figure 1. Output Short Circuit Parameter Diagram
8
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
6.7 Typical Characteristics
RDS(ON) - On Resistance (m:)
40
30
20
10
0
-40
IREV - Reverse Leakage Current (µA)
500
-25
-10
5
20 35 50 65 80
TJ - Junction Temperature (oC)
95
450
400
350
300
250
-40
110 125
-25
-10
D001
5
20 35 50 65 80
TJ - Junction Temperature (oC)
95
110 125
D001
Figure 2. VBUS Current Limiting Switch On Resistance vs
Temperature
Figure 3. VCONN Current Limiting Switch On Resistance vs
Temperature
0.25
4000
3500
0.2
ILIM - Limit Current (mA)
RDS(ON) - On Resistance (m:)
50
0.15
0.1
3000
VBUS ILIM 3 A
VBUS ILIM 1.5 A
VCONN_ILIM
2500
2000
1500
1000
0.05
500
0
-40
-25
-10
5
20 35 50 65 80
TJ - Junction Temperature (oC)
95
0
-40
110 125
-25
-10
D001
5
20 35 50 65 80
TJ - Junction Temperature (oC)
95
110 125
D001
Device = Disabled; (VOUT-VIN) =6.5V
Figure 5. ILIM for VBUS and VCON vs Temperature
350
LD_DET Threshold Rising
LD_DET Threshold Falling
300
Sourcing Current (PA)
LD_DET Threshold (mA)
Figure 4. OUT Reverse Leakage Current vs Temperature
2010
1990
1970
1950
1930
1910
1890
1870
1850
1830
1810
1790
1770
1750
-40
UFP 3 A
UFP 1.5 A
UFP 0.5 A/0.9 A
250
200
150
100
-25
-10
5
20 35 50 65 80
TJ - Junction Temperature (oC)
95
110 125
50
-40
-25
D001
Figure 6. LD_DET Threshold vs Temperature
-10
5
20 35 50 65 80
TJ - Junction Temperature (oC)
95
110 125
D001
Figure 7. CC Sourcing Current to UFP vs Temperature
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
9
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
Typical Characteristics (continued)
95
400
IN1 UFP 3 A
IN1 UFP 0.5 A/1.5 A
IIN_ON - Enabled IN Supply Current (PA)
IIN_ON - Enabled IN Supply Current (PA)
100
90
85
80
75
70
-40
-25
-10
5
20 35 50 65 80
TJ - Junction Temperature (oC)
95
110 125
350
300
IN2 UFP 3 A
IN2 UFP 1.5 A
IN2 UFP 0.5 A
250
200
150
100
50
-40
-25
-10
D001
Figure 8. IN1 Current with UFP vs Temperature
5
20 35 50 65 80
TJ - Junction Temperature (oC)
95
110 125
D001
Figure 9. IN2 Current with UFP vs Temperature
IIN_ON - Enabled IN Supply Current (µA)
70
65
60
55
50
45
40
-40
-25
-10
5
20 35 50 65 80
TJ - Junction Temperature (oC)
95
110 125
D001
VAUX = 5 V
Figure 10. AUX Current with UFP vs Temperature
10
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
7 Detailed Description
7.1 Overview
The TPS25810 is a highly integrated USB Type-C Downstream Facing Port (DFP) controller with built-in power
switch developed for the new USB Type-C connector and cable. The part provides all functionality needed to
support a USB Type C DFP in a system where USB power delivery (PD) source capabilities (for example, VBUS
> 5 V) are not implemented. The device is designed to be compliant to Type-C spec revision 1.2.
7.1.1 USB Type C Basic
For a detailed description of the Type-C spec refer to the USB-IF website to download the latest released
version. Some of the basic concepts of the Type-C spec that pertains to understanding the operation of the
TPS25810 (a DFP device) are described as follows.
USB Type-C removes the need for different plug and receptacle types for host and device functionality. The
Type-C receptacle replaces both Type-A and Type-B receptacle since the Type-C cable is plug-able in either
direction between host and device. A host-to-device logical relationship is maintained via the configuration
channel (CC). Optionally hosts and devices can be either providers or consumers of power when USB PD
communication is used to swap roles.
All
•
•
•
USB Type-C ports operate in one of below three data modes:
Host mode: the port can only be host (provider of power)
Device mode: the port can only be device (consumer of power)
Dual-Role mode: the port can be either host or device
Port types:
• DFP (Downstream Facing Port): Host
• UFP (Upstream Facing Port): Device
• DRP (Dual-Role Port): Host or Device
Valid DFP-to-UFP connections:
• Table 1 describes valid DFP-to-UFP connections
• Host to Host or Device to Device have no functions
Table 1. DFP-to-UFP Connections
HOST-MODE PORT
(1)
DEVICE-MODE
PORT
DUAL-ROLE PORT
Host-Mode Port
No Function
Works
Works
Device-Mode Port
Works
No Function
Works
Dual-Role Port
Works
Works
Works (1)
This may be automatic or manually driven.
7.1.2 Configuration Channel
The function of the configuration channel is to detect connections and configure the interface across the USB
Type-C cables and connectors.
Functionally the Configuration Channel (CC) is used to serve the following purposes:
• Detect connect to the USB ports
• Resolve cable orientation and twist connections to establish USB data bus routing
• Establish DFP and UFP roles between two connected ports
• Discover and configure power: USB Type-C current modes or USB Power Delivery
• Discovery and configure optional Alternate and Accessory modes
• Enhances flexibility and ease of use
Typical flow of DFP to UFP configuration is shown in Figure 11:
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
11
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
Figure 11. Flow of DFP to UFP Configuration
7.1.3 Detecting a Connection
DFPs and DRPs fulfill the role of detecting a valid connection over USB Type-C. Figure 12 shows a DFP to UFP
connection made with Type C cable. As shown in Figure 12, the detection concept is based on being able to
detect terminations in the product which has been attached. A pull-up and pull-down termination model is used. A
pull-up termination can be replaced by a current source.
• In the DFP-UFP connection the DFP monitors both CC pins for a voltage lower than the unterminated
voltage.
• An UFP advertises Rd on both its CC pins (CC1 and CC2).
• A powered cable advertises Ra on only one of CC pins of the plug. Ra is used to inform the source to apply
VCONN.
• An analog audio device advertises Ra on both CC pins of the plug, which identifies it as an analog audio
device. VCONN is not applied on either CC pin in this case.
UFP monitors for
connection
DFP monitors for
connection
Cable
CC
Rp
Rp
Ra
Rds
Ra
Rds
DFP monitors for
connection
UFP monitors for
connection
Figure 12. DFP-UFP Connection
12
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
7.2 Functional Block Diagram
IN1
Current Sense
IN2
Current Sense
OUT
OTSD
Thermal
Sense
UVLO
CC1
Current Sense
CC2
UVLO
AUX
LD_DET
CC
Monitor
UVLO
Current
Limit
FAULT
Charge
Pump
Gate
Control
EN
UFP
POL
Control
Logic
CHG
AUDIO
CHG_HI
DEBUG
REF
REF_RTN
Copyright © 2016, Texas Instruments Incorporated
7.3 Feature Description
The TPS25810 is a DFP Type C port controller with integrated power switch for VCONN and VBUS. The
TPS25810 does not support BC1.2 charging modes since it does not interact with USB D+/D- data lines. It can
be used in conjunction with a BC 1.2 device like the TPS2514A, to support BC1.2 and Type C charging modes in
a single Type C DFP port. See the TPS25810 EVM user's guide (SLVUAI0) and Application and Implementation
section of this data sheet for more details. The TPS25810 can be used in a USB 2.0 only or USB 3.1 port
implementation. When used in a USB 3.1 port, the TPS25810 can control an external super speed MUX to
handle the Type C flippable feature.
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
13
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
Feature Description (continued)
7.3.1 Configuration Channel Pins CC1 and CC2
The TPS25810 has two pins, CC1 and CC2 that serve to detect an attachment to the port and resolve cable
orientation. These pins are also used to establish current broadcast to a valid UFP, configure VCONN, and
detect Debug or Audio Adapter Accessory attachment.
Table 2 lists TPS25810 response to various attachments to its port.
Table 2. TPS25810 Response
TPS25810 RESPONSE (1)
OUT
VCONN
On CC1 or
CC2
POL
OPEN
OPEN
NO
OPEN
IN1
NO
OPEN
Rd
IN1
Powered Cable/No UFP
Connected
OPEN
Ra
Powered Cable/No UFP
Connected
Ra
Powered Cable/UFP
Connected
TPS25810 TYPE C PORT
CC1
CC2
Nothing Attached
OPEN
UFP Connected
Rd
UFP Connected
UFP
AUDIO
DEBUG
Hi-Z
Hi-Z
Hi-Z
Hi-Z
Hi-Z
LOW
Hi-Z
Hi-Z
NO
LOW
LOW
Hi-Z
Hi-Z
OPEN
NO
Hi-Z
Hi-Z
Hi-Z
Hi-Z
OPEN
OPEN
NO
Hi-Z
Hi-Z
Hi-Z
Hi-Z
Rd
Ra
IN1
CC2
Hi-Z
LOW
Hi-Z
Hi-Z
Powered Cable/UFP
Connected
Ra
Rd
IN1
CC1
LOW
LOW
Hi-Z
Hi-Z
Debug Accessory Connected
Rd
Rd
OPEN
NO
Hi-Z
Hi-Z
Hi-Z
LOW
Audio Adapter Accessory
Connected
Ra
Ra
OPEN
NO
Hi-Z
Hi-Z
LOW
Hi-Z
(1)
POL, UFP, AUDIO, and DEBUG are open drain outputs; pull high with 100 kΩ to AUX when used. Tie to GND or leave open when not
used.
7.3.2 Current Capability Advertisement and Overload Protection
The TPS25810 supports all three Type-C current advertisements as defined by the USB Type C standard.
Current broadcast to a connected UFP is controlled by the CHG and CHG_HI pins. For each broadcast level the
device protects itself from a UFP that draws current in excess of the port’s USB Type-C Current advertisement
by setting the current limit as shown in Table 3.
Table 3. USB Type-C Current Advertisement
CHG
CHG_HI
CC CAPABILITY
BROADCAST
CURRENT LIMIT (typ)
LOAD DETECT
THRESHOLD (typ)
0
0
STD
1.7 A
NA
0
1
STD
1.7 A
NA
1
0
1.5 A
1.7 A
NA
1
1
3A
3.4 A
1.95 A
Under overload conditions, the internal current-limit regulator limits the output current to selected ILIM for OUT
and fixed internal VCONN current limit as shown in the Electrical Characteristics. When an overload condition is
present, the device maintains a constant output current, with the output voltage determined by (iOS x RLOAD).
Two possible overload conditions can occur. The first overload condition occurs when either: 1) input voltage is
first applied, enable is true, and a short circuit is present (load which draws IOUT > iOS), or 2) input voltage is
present and the TPS25810 is enabled into a short circuit. The output voltage is held near zero potential with
respect to ground and the TPS25810 ramps the output current to iOS. The TPS25810 limits the current to iOS until
the overload condition is removed or the device begins to thermal cycle. This is demonstrated in Figure 24 where
the device was enabled into a short, and subsequently cycles current off and on as the thermal protection
engages.
14
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
The second condition is when an overload occurs while the device is enabled and fully turned on. The device
responds to the overload condition within time iOS (see Figure 1) when the specified overload (per Electrical
Characteristics) is applied. The response speed and shape vary with the overload level, input circuit, and rate of
application. The current-limit response varies between simply settling to iOS or turnoff and controlled return to iOS.
Similar to the previous case, the TPS25810 limits the current to iOS until the overload condition is removed or the
device begins to thermal cycle.
The TPS25810 thermal cycles if an overload condition is present long enough to activate thermal limiting in any
of the above cases. This is due to the relatively large power dissipation [(VIN – VOUT) x iOS] driving the junction
temperature up. The device turns off when the junction temperature exceeds 135°C (min) while in current limit.
The device remains off until the junction temperature cools 20°C and then restarts. The TPS25810 current limit
profile is shown in Figure 13.
VIN
Slope = -rDSON
VOUT
0A
0V
IOUT
IOS
Figure 13. Current Limit Profile
7.3.3 Undervoltage Lockout (UVLO)
The undervoltage lockout (UVLO) circuit disables the power switch until the input voltage reaches the UVLO turnon threshold. Built-in hysteresis prevents unwanted on/off cycling due to input voltage droop during turn on.
7.3.3.1 Device Power Pins (IN1, IN2, AUX, OUT, and GND)
The device has multiple input power pins; IN1, IN2 and AUX. IN1 is connected to OUT by the internal power FET
and serves the supply for the Type-C charging current. IN2 is the supply for VCONN and ties directly between
the VCONN power switch on its input and CC1 or CC2 on its output. AUX or auxiliary input supply provides
power to the chip. Refer to Functional Block Diagram.
In the simplest implementation where multiple supplies are not available; IN1, IN2, and AUX can be tied together.
However in mobile systems (battery powered) where system power savings is paramount, IN1 and IN2 can be
powered by the high power DC-DC supply (>3-A capability) while AUX can be connected to the low power supply
that typically powers the system uC when the system is in hibernate or sleep power state. Unlike IN1 and IN2,
AUX can operate directly from a 3.3-V supply commonly used to power the uC when the system is put in low
power mode. A ceramic bypass capacitor close to the device from IN/AUX to GND is recommended to alleviate
bus transients.
The recommended operating voltage range for IN1/IN2 is 4.5 V to 5.5 V while AUX can be operated from 2.9 V
to 5.5 V. However IN1, the high power supply, can operate up to 6.5 V. This higher input voltage affords a larger
IR drop budget in systems where a long cable harness is used and results in high IR drops with 3-A charging
current. Increasing IN1 beyond 5.5 V enables longer cable/board trace lengths between the device and Type C
receptacle while meeting the USB spec for VBUS at connector ≥ 4.75 V.
Figure 14 illustrates the point. In this example IN1 is at 5 V which restricts the IR drop budget from DC-DC to
connector to 250 mV.
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
15
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
Total IR loss Budget = 250 mV
Trace IR drop Budget at 3 A
= 250-165 = 85 mV
V_Trace1
V_Trace2
V_TPS25810
IN1
Type C
V_DC-DC = 5 V
OUT
5 V DC-DC
MaxRds_On
= 55 mŸ
165 mV drop at 3 A
82.5 mV drop at 1.5 A
V_Connector
= 4.75 V (MIN)
Figure 14. Total IR Loss Budget
7.3.3.2 FAULT Response
The FAULT pin is an open drain output that asserts (active low) when device OUT current exceeds its
programmed value and the over temperature threshold is crossed (TTH_OTSD1). Refer to the Electrical
Characteristics for over current and temperature values. The FAULT signal remains asserted until the fault
condition is removed and the device resumes normal operation. The TPS25810 is designed to eliminate false
overcurrent fault reporting by using an internal deglitch circuit.
Connect FAULT with a pull-up resistor to AUX. FAULT can be left open or tied to GND when not used.
7.3.3.3 Thermal Shutdown
The device has two internal over temperature shutdown thresholds, TTH_OTSD1 and TTH_OTSD2, to protect the
internal FET from damage and overall safety of the system. TTH_OTSD2 > TTH_OTSD1. FAULT is asserted low to
signal a fault condition when device temperature exceeds TTH_OTSD1 and the current limit switch is disabled.
However when TTH_OTSD2 is exceeded all open drain outputs are left open and the device is disabled such that
minimum power/heat is dissipated. The device attempts to power-up when die temperature decreases by 20°C.
7.3.3.4 REF
A 100-kΩ (1% or better recommended) resistor is connected from this pin to REF_RTN. This pin sets the
reference current required to bias the internal circuitry of the device. The overload current limit tolerance and CC
currents depend upon the accuracy of this resistor, using a ±1% low tempco resistor, or better, yields the best
current limit accuracy and overall device performance.
7.3.3.5 Audio Accessory Detection
The USB Type-C spec defines an audio adapter decode state which allows implementation of an analog USB
Type-C to 3.5-mm headset adapter. The TPS25810 detects an audio accessory device when both CC1 and CC2
pins sees VRa voltage (when pulled to ground by Ra resistor). The device asserts the open drain AUDIO pin low
to indicate the detection of such a device.
16
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
Table 4. Audio Accessory Detection
CC1
CC2
AUDIO
STATE
Ra
Ra
Asserted (pulled low)
Audio Adapter Accessory Connected
Platforms supporting this extension can trigger off of the AUDIO pin to enable accessory mode circuits to support
the audio function. When the Ra pull-down is removed from the CC2 pin, AUDIO is de-asserted or pulled high.
The TPS25810 monitors the CC2 pin for audio device detach. When this function is not needed (for example in a
data-less port) AUDIO can be tied to GND or left open.
7.3.3.6 Debug Accessory Detection
The Type-C spec supports an optional Debug Accessory mode used for debug only and must not be used for
communicating with commercial products. When the TPS25810 detects VRd voltage on both CC1 and CC2 pins
(when pulled to ground by an Rd resistor), it asserts DEBUG low. With DEBUG is asserted, the system can enter
debug mode for factory testing or a similar functional mode. DEBUG de-asserts or pulls high when Rd is
removed from CC1. The TPS25810 monitors the CC1 pin for Debug Accessory detach.
If Debug accessory mode is not used, tie DEBUG to GND or leave it open.
Table 5. Debug Accessory Detection
CC1
CC2
POL
STATE
Rd
Rd
Asserted (pulled low)
Debug Accessory Mode connected
7.3.3.7 Plug Polarity Detection
Reversible Type-C plug orientation is reported by the POL pin when a UFP is connected. However when no UFP
is attached, POL remains de-asserted irrespective of cable plug orientation. Table 6 describes the POL state
based on which device CC pin detects VRD from an attached UFP pull-down.
Table 6. Plug Polarity Detection
CC1
CC2
POL
STATE
Rd
Open
Hi-z
UFP connected
Open
Rd
Asserted (pulled low)
UFP connected with reverse plug orientation
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
17
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
Figure 15 shows an example implementation which utilizes the POL terminal to control the SEL terminal on the
HD3SS3212. The HD3SS3212 provides switching on the differential channels between Port B and Port C to Port
A depending on cable orientation.
3.3 V
HD3SS3212
USB Host
VCC
USB C
B0+
B0–
SSTXp
A0+
SSTXn
A0–
SSRXp
A1+
SSRXn
Dp
A1–
Dp
Dm
Dm
0.1 µF
0.1 µF
0.1 µF
C0+
0.1 µF
C0–
SSTXp2
Dp1
SSTXn2
Dp2
SSTXp1
Dm1
SSTXn1
Dm2
B1+
SSRXp2
B1–
SSRXn2
OEn
C1+
SSRXp1
GND
SEL
C1–
SSRXn1
GND
Dp
Dm
GND
GND
CC2
VBUS
GND
GND
GND
CC1
3.3 V
TPS25810
5V
POL
UFP
IN1
IN1
OUT
OUT
CC1
CC2
5V
IN2
AUX
EN
CHG
CHG HI
_
REF
REF_RTN
LD_DET
GND
Thermal Pad
FAULT
AUDIO
DEBUG
Copyright © 2016, Texas Instruments Incorporated
Figure 15. Example Implementation
7.3.3.8 Device Enable Control
The logic enable pin controls the power switch and device supply current. The supply current is reduced to less
than 1 μA when a logic low is present on EN. The EN pin provides a convenient way to turn on or turn off the
device while it is powered. The enable input threshold has hysteresis built-in. When this pin is pulled high, the
device is turned on or enabled. When the device is disabled (EN pulled low) the internal FETs tied to IN1 and
IN2 are disconnected, all open drain outputs are left open (Hi-Z), and the CC1/CC2 monitor block is turned off.
The EN terminal should not be left floating.
7.3.3.9 Load Detect
The load detect function in the device is enabled when it is set to broadcast high current VBUS charging (CHG =
CHG_HI = High) on the CC pin. In this mode the device monitors the current to a UFP; if the current exceeds
1.95 A (TYP) the LD_DET pin asserts. Since LD_DET is an open drain output, pull it high with 100 kΩ to AUX
when used; tie it to GND or leave open when not used.
18
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
7.3.3.10
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
Power Wake
Both /UFP High
Converter
Disabled
IN1
TPS54620
Buck
Converter
EN
IN2
AUX
CHG
TPS25810
#1
USB Type-C
Connector
The power wake feature supported in the TPS25810 offers the mobile systems designer a way to save on
system power when no UFP is attached to the Type-C port. Refer to Figure 16. To enable power wake the UFP
from device #1 and #2 are tied together (each with its own 100-kΩ pull-up) to the enable pin of a 5 V/6 A dc-dc
buck converter. When no UFP is detected on both Type-C ports, the EN pin of the dc-dc is pulled high thereby
disabling it. Since both TPS25810s are powered by an always-on 3.3-V LDO, turning off the IN1/IN2 supply does
not affect its operation in detach state. Anytime a UFP is detected on either port, the corresponding TPS25810
UFP pin is pulled low enabling the dc-dc to provide charging current to the attached UFP. Turning off the high
power dc-dc when ports are unattached saves on system power. This method can save a significant amount of
power considering the TPS25810 only requires < 5 µA when no UFP device is connected.
OUT
CC1
CC2
No UFP
Attached
/UFP_1
CHG_HI
12V
IN1
IN2
AUX
CHG
LP2950-33
LDO
TPS25810
#2
USB Type-C
Connector
/UFP_1 /UFP_2
(High)
(High)
OUT
CC1
CC2
No UFP
Attached
/UFP_2
One /UFP Low
Converter
Enabled
IN1
TPS54620
Buck
Converter
EN
IN2
AUX
CHG
TPS25810
#1
USB Type-C
Connector
CHG_HI
OUT
CC1
CC2
UFP
Attached
/UFP_1
CHG_HI
12V
IN1
IN2
AUX
CHG
LP2950-33
LDO
TPS25810
#2
USB Type-C
Connector
/UFP_1 /UFP_2
(Low)
(High)
OUT
CC1
CC2
No UFP
Attached
/UFP_2
CHG_HI
Copyright © 2016, Texas Instruments Incorporated
Figure 16. Power Wake Implementation
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
19
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
7.3.3.11 Port Power Management (PPM)
PPM is the intelligent and dynamic allocation of power made possible with the use of the LD_DET pin. It is for
systems that have multiple charging ports but cannot power them all at their maximum charging current
simultaneously.
Goals of PPM are:
1. Enhances user experience since user does not have to search for high current charging port.
2. Lowered cost and size of power supply needed for implementing high current charging in a multi-port system.
7.3.3.12 Implementing PPM in a System with Two Type-C Ports
Figure 17 shows PPM and power wake implemented in a system with two Type C ports both initially set to
broadcast high current charging (3 A, CHG and CHG_HI pulled high via a 100 kΩ to AUX). To enable PPM tie
the LD_DET pin from TPS25810 #1 to CHG_HI of TPS25810 #2 and vice versa as shown in Figure 17. Each
device independently monitors charging current drawn by its attached UFP.
IN1
IN2
TPS54620
Buck
Converter
EN
AUX
CHG
TPS25810
#1
OUT
CC1
CC2
/LD_DET_1
/UFP_1
USB Type-C
Connector
IN1, IN2 are connected to a TPS54620; a 6-A synchronous step-down converter. AUX is powered by a LP295033; a low quiescent current 3.3-V LDO. With no UFP attached to either Type C port the TPS25810 is powered by
the LP2950-33. This method saves a significant amount of power considering the TPS25810 requires less than 2
µA when no USB device is connected.
CHG_HI
12V
IN1
IN2
LP2950-33
LDO
AUX
CHG
TPS25810
#2
USB Type-C
Connector
/UFP_1 /UFP_2
OUT
CC1
CC2
/LD_DET_2
/UFP_2
3.0A Broadcast
CHG_HI
Copyright © 2016, Texas Instruments Incorporated
Figure 17. PPM and Power Wake Implemented
7.3.3.13 PPM Operation
When no UFP is attached, or either of the two attached UFP is drawing current less than the LD_DET threshold
(1.95 A typical), the LD_DET output for both devices is high (shown in blue in Figure 18). Now when a UFP is
attached to device #1 that draws a charging current higher than the LD_DET threshold (1.95 A), this causes
LD_DET to assert or pull-low (shown in red in Figure 18). Since the LD-DET pins of the #1 and #2 devices are
connected to the other devices CHG_HI pin, a high current detection on device #1 forces device #2 to broadcast
1.5 A or medium charging current capability on its CC pin. The Type C specification requires a UFP to monitor
the CC pins continuously and adjust its current consumption (within 60 ms) to remain within the value advertised
by the DFP.
Figure 19 shows the case when a UFP attached to Device 1 reduces its charging current below the LD_DET
threshold, which causes LD-DET to de-assert, thereby toggling device #2 CH_HI pin from low to high.
This scheme:
• Delivers a better user experience as the user does not have to worry about the maximum charging current
rating of the host ports, both ports initially advertise high current charging.
20
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
IN1
IN2
TPS54620
Buck
Converter
EN
AUX
CHG
TPS25810
#1
OUT
CC1
CC2
/LD_DET_1
/UFP_1
USB Type-C
Connector
Enables a smaller and lower cost power supply as the loading is controlled and never allowed to exceed 5 A.
3.0A USB Device Connected
USB Type-C
Connector
•
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
1.5A Broadcast
CHG_HI
12V
/UFP_1 /UFP_2
IN1
IN2
LP2950-33
LDO
AUX
CHG
TPS25810
#2
OUT
CC1
CC2
/LD_DET_2
/UFP_2
CHG_HI
Copyright © 2016, Texas Instruments Incorporated
AUX
CHG
TPS25810
#1
OUT
CC1
CC2
/LD_DET_1
/UFP_1
USB Type-C
Connector
IN1
IN2
TPS54620
Buck
Converter
EN
1.5A USB Device Connected
USB Type-C
Connector
Figure 18. 3-A USB Device Connected
3.0A Broadcast
CHG_HI
12V
/UFP_1 /UFP_2
IN1
IN2
LP2950-33
LDO
AUX
CHG
TPS25810
#2
OUT
CC1
CC2
/LD_DET_2
/UFP_2
CHG_HI
Copyright © 2016, Texas Instruments Incorporated
Figure 19. 1.5-A USB Device Connected
7.4 Device Functional Modes
The TPS25810 is a Type-C controller with integrated power switch that supports all Type-C functions in a
downstream facing port. It is also used to manage current advertisement and protection to a connected UFP and
active cable. The device starts its operation by monitoring the AUX bus. When VAUX exceeds the under voltagelockout threshold, the device samples the EN pin. A high level on this pin enables the device and normal
operation begins. Having successfully completed its start-up sequence, the device now actively monitors its CC1
and CC2 pins for attachment to a UFP. When a UFP is detected on either the CC1 or CC2 pin the internal
MOSFET starts to turn-on after the required de-bounce time is met. The internal MOSFET starts conducting and
allows current to flow from IN1 to OUT. If Ra is detected on the other CC pin (not connected to UFP), VCONN is
applied to allow current to flow from IN2 to the CC pin connected to Ra. For a complete listing of various device
operational modes refer to Table 2.
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
21
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The TPS25810 is a Type-C DFP controller that supports all Type-C DFP required functions. The TPS25810 only
applies power to VBUS when it detects that a UFP is attached and removes power when it detects the UFP is
detached. The device exposes its identity via its CC pin advertising its current capability based on CHG and
CHG_HI pin settings. The TPS25810 also limits its advertised current internally and provides robust protection to
a fault on the system VBUS power rail.
After a connection is established by the TPS25810, the device is capable of providing VCONN to power circuits in
the cable plug on the CC pin that is not connected to the CC wire in the cable. VCONN is internally current limited
and has its own supply pin IN2. Apart from providing charging current to a UFP, the TPS25810 also supports
Audio and Debug accessory modes.
The following design procedure can be used to implement a full featured Type-C DFP.
NOTE
BC 1.2 is not supported in the TPS25810. To support BC1.2 with Type-C charging modes
in a single C connector, a device like a TPS2514A will need to be used.
8.2 Typical Applications
8.2.1 Type C DFP Port Implementation without BC 1.2 Support
Figure 20 shows a minimal Type-C DFP implementation capable of supporting 5-V and 3-A charging.
5V
0.1uF
47uF
47uF
47uF
2
3
4
5
6
7
8
10
100 NŸ
(1%)
9
USB Type C
Receptacle
TPS 25810RVC
IN1
OUT
IN1
OUT
IN2
CC2
AUX
CC1
FAULT
EN
LD_DET
CHG
UFP
CHG_HI
POL
AUDIO
REF
DEBUG
GND
REF_RTN
PAD
14
VBUS
15
13
11
1
20
19
18
17
16
10uF
12
21
Copyright © 2016, Texas Instruments Incorporated
Figure 20. Type-C DFP Port Implementation without BC 1.2 Support
22
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
Typical Applications (continued)
8.2.1.1 Design Requirements
8.2.1.1.1 Input and Output Capacitance
Input and output capacitance improves the performance of the device. The actual capacitance should be
optimized for the particular application. For all applications, a 0.1-μF or greater ceramic bypass capacitor
between IN and GND is recommended as close to the device as possible for local noise de-coupling.
All protection circuits such as the TPS25810 have the potential for input voltage overshoots and output voltage
undershoots. Input voltage overshoots can be caused by either of two effects. The first cause is an abrupt
application of input voltage in conjunction with input power bus inductance and input capacitance when the IN
terminal is high impedance (before turn on). Theoretically, the peak voltage is 2 times the applied. The second
cause is due to the abrupt reduction of output short circuit current when the TPS25810 turns off and energy
stored in the input inductance drives the input voltage high. Input voltage droops may also occur with large load
steps and as the TPS25810 output is shorted. Applications with large input inductance (for instance connecting
the evaluation board to the bench power-supply through long cables) may require large input capacitance to
reduce the voltage overshoot from exceeding the absolute maximum voltage of the device.
The fast current-limit speed of the TPS25810 to hard output short circuits isolate the input bus form faults.
However, ceramic input capacitance in the range of 1 μF to 22 μF adjacent to the TPS25810 input aids in both
response time and limiting the transient seen on the input power bus. Momentary input transients to 6.5 V are
permitted. Output voltage undershoot is caused by the inductance of the output power bus just after a short has
occurred and the TPS25810 has abruptly reduced OUT current. Energy stored in the inductance drives the OUT
voltage down and potentially negative as it discharges. An application with large output inductance (such as from
a cable) benefits from use of a high-value output capacitor to control voltage undershoot.
When implementing a USB standard application, 120 μF minimum output capacitance is required. Typically a
150-μF electrolytic capacitor is used, which is sufficient to control voltage undershoots. Since in Type-C DFP is a
cold socket when no UFP is attached, the output capacitance should be placed at the IN pin versus OUT as is
used in USB Type A ports. It is also recommended to put a 10-μF ceramic capacitor on the OUT pin for better
voltage bypass.
8.2.1.2 Detailed Design Procedure
The TPS25810 device supports three different input voltages based on the application. In the simplest
implementation all input supplies are tied to a single voltage source as shown in Figure 20 which is set to 5 V.
However, it is recommended to set a slightly higher (100 mV to 200 mV) input voltage, when possible, to
compensate for IR drop from the source to the Type C connector.
Other design considerations are listed below:
• Place at least 120 µF of bypass capacitance close to the IN pins versus OUT as Type C is a cold socket
connector.
• A 10-µF bypass capacitor is recommended placed near a Type-C receptacle VBUS pin to handle load
transients.
• Depending on the max current level advertisement supported by the Type-C port in the system, set CHG and
CHG_HI levels accordingly. 3 A advertisement is shown in Figure 20.
• EN, CHG, and CHG_HI pins can be tied directly to GND or VAUX without a pull-up resistor.
– CHG and CHG_HI can also be dynamically controlled by a µC to change the current advertisement level
to the UFP.
• When an open drain output of the TPS25810 is not used, it can be left as NC or tied to GND.
• Use a 1% 100-kΩ resistor to connect between the REF and REF_RTN pins placing it close to the device pin
and isolated from switching noise on the board.
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
23
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
Typical Applications (continued)
VIN
2 V/div
VBUS
2 V/div
2 V/div
8.2.1.3 Application Curves
2 V/div
2 V/div
CC1
VIN
VBUS
CC1
Time 20 ms/div
Time 50 ms/div
Basic Start-Up: IN1 = IN2 = AUX = EN = CHG = CHG_HI = 5 V,
CC1 = Rd, CC2 = Open
IN1 = IN2 = AUX = EN = CHG = CHG_HI = 5 V, CC1 = Open,
CC2 = Open then Rd
2 V/div
2 V/div
VBUS VIN
2 V/div
IN
500 mA/div
CC1
VIN
VBUS
2 V/div
2 V/div
Figure 22. Start-Up
CC1
2 A/div
2 V/div
Figure 21. Basic Start-Up
IN
Time 50 ms/div
Time 200 ms/div
IN1 = IN2 = AUX = EN = 5 V; CHG = CHG_HI = 0 V, CC1 =
Open, CC2 = Rd, OUT = Open→5 Ω
IN1 = IN2 = AUX = EN = CHG = CHG_HI = 5 V, CC1 = Rd, CC2
= Open, OUT = Shorted
Figure 24. Hot-Plug to Short
2 V/div
VIN
IN
2 V/div
VOUT
CC1
2 V/div
2 V/div
CC1
2 A/div
VIN
2 V/div
VBUS
2 V/div
2 V/div
Figure 23. Load Step
CC2
Time 20 ms/div
Time 20 ms/div
IN1 = IN2 = AUX = EN = CHG = CHG_HI = 5 V, CC1 = Short,
CC2 = Rd
IN1 = IN2 = AUX = EN = CHG = CHG_HI = 5 V, CC1 = Open,
CC2 = Rd→Open
Figure 25. Short On CC1
24
2 V/div
2 V/div
2 A/div
CC2
IN
Figure 26. Remove Rd
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
VIN
VBUS
CC2
2 V/div
CC1
2 V/div
2 V/div
2 V/div
Typical Applications (continued)
Time 50 ms/div
VIN 5 V→3.5 V (100 ms)→5 V (1 V/ms),
IN1 = IN2 = AUX = EN = CHG = CHG_HI = 5 V,
CC1 = Rd,
CC2 = Ra
Figure 27. Brown-Out Test
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
25
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
Typical Applications (continued)
8.2.2 Type-C DFP Port Implementation with BC 1.2 (DCP Mode) Support
Figure 28 shows a Type-C DFP implementation capable of supporting 5 V and 3 A charging in a Type-C port that
is also able to support charging of legacy devices when used with a Type C – µB cable assembly for charging
phones and handheld devices equipped with µB connector.
This implementation requires the use of a TPS2514A, a USB dedicated charging port (DCP) controller with autodetect feature to charge not only BC1.2 compliant handheld devices but also popular phones and tablets that
incorporate their own propriety charging algorithm. Refer to TPS2514A specifications available at www.ti.com for
more details.
TPS2514ADBV
IN DM1
DP1
NC
GND NC
0.1uF
TPS 25810RVC
5V
2
0.1uF
47uF
47uF
47uF
3
4
5
6
7
8
10
100 NŸ
(1%)
9
IN1
IN1
IN2
AUX
OUT
OUT
CC2
CC1
FAULT
LD_DET
CHG
UFP
CHG_HI
POL
AUDIO
REF
DEBUG
EN
GND
REF_RTN
PAD
14
VBUS
Dn
Dp
15
13
11
1
20
19
18
17
16
10uF
USB Type C
Receptacle
12
21
Copyright © 2016, Texas Instruments Incorporated
Figure 28. Type C DFP Port Implementation with BC 1.2 (DCP Mode) Support
8.2.2.1 Design Requirements
Refer to Design Requirements for the Design Requirements.
8.2.2.2 Detailed Design Procedure
Refer to Detailed Design Procedure for the Detailed Design Procedure.
8.2.2.3 Application Curves
Refer to Application Curves for the Application Curves.
26
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
9 Power Supply Recommendations
The device has three power supply inputs; IN1, which is directly connected to OUT via the power MOSFET, is
tied to the VBUS pin in the Type-C receptacle. IN2 also has a current limiting switch and is MUXed either to the
CC1 or CC2 pin in the Type-C receptacle depending on cable plug polarity. AUX is the chip supply. In most
applications all three supplies are tied together. In a special implementation like power wake IN1/IN2 are tied to a
single supply while AUX is powered by a supply that is always ON and can be as low as 2.9 V.
USB Specification Revisions 2.0 and 3.1 require VBUS voltage at the connector to be between 4.75 V to 5.5 V.
Depending on layout and routing from supply to the connector the voltage droop on VBUS has to be tightly
controlled. Locate the input supply close to the device. For all applications, a 10-μF or greater ceramic bypass
capacitor between OUT and GND is recommended as close to the Type-C connector of the device as possible
for local noise decoupling. The power supply should be rated higher than the current limit set to avoid voltage
droops during over current and short-circuit conditions.
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
27
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
10 Layout
10.1 Layout Guidelines
Layout best practices as it applies to the TPS25810 are listed below.
• For all applications a 10-µF ceramic capacitor is recommended near the Type-C receptacle and another 120µF ceramic capacitor close to IN1 pin.
– The optimum placement of the 120-µF capacitor is closest to the IN1 and GND pins of the device.
– Care must be taken to minimize the loop area formed by the bypass-capacitor connection, the IN1 pin,
and the GND pin of the IC. See Figure 29 for a PCB layout example.
• High current carrying power path connections to the device should be as short as possible and should be
sized to carry at least twice the full-load current.
– Have the input and output traces as short as possible. The most common cause of voltage drop failure in
USB power delivery is the resistance associated with the VBUS trace. Trace length, maximum current
being supplied for normal operation, and total resistance associated with the VBUS trace must be taken
into account while budgeting for voltage drop.
– For example, a power carrying trace that supplies 3 A, at a distance of 20 inches, 0.100-in. wide, with 2oz. copper on the outer layer will have a total resistance of approximately 0.046 Ω and voltage drop of
0.14 V. The same trace at 0.050-in.-wide will have a total resistance of approximately 0.09 Ω and voltage
drop of 0.28 V.
– Make power traces as wide as possible.
• The resistor attached to the REF pin of the device has several requirements:
– It is recommended to use a 1% 100-kΩ low tempco resistor.
– It should be connected to pins REF and REF_RTN (pin 9 and pin 10 respectively).
– The REF_RTN pin should be isolated from the GND plane. See Figure 29.
– The trace routing between the REF and REF_RTN pins of the device should be as short as possible to
reduce parasitic effects on current limit and current advertisement accuracy. These traces should not have
any coupling to switching signals on the board.
• Locate all TPS25810 pull-up resistors for open-drain outputs close to their connection pin. Pull up resistors
should be 100 kΩ.
– When a particular open drain output is not used/needed in the system leave the associated pin open or
tied to GND.
• Keep the CC lines close to the same length.
• Thermal Considerations:
– When properly mounted, the thermal pad package provides significantly greater cooling ability than an
ordinary package. To operate at rated power, the thermal pad must be soldered to the board GND plane
directly under the device. The thermal pad is at GND potential and can be connected using multiple vias
to inner layer GND. Other planes, such as the bottom side of the circuit board can be used to increase
heat sinking in higher current applications. Refer to Technical Briefs: PowerPad™ Thermally Enhanced
Package (TI literature Number SLMA002) and PowerPAD™ Made Easy (TI Literature Number SLMA004)
or more information on using this thermal pad package.
– The thermal via land pattern specific to the TPS25810 can be downloaded from the device web page at
www.ti.com.
– Obtaining acceptable performance with alternate layout schemes is possible; however the layout example
in the following section has been shown to produce good results and is intended as a guideline.
• ESD Considerations
– TPS25810 has built in ESD protection for CC1 and CC2. Keep trace length to a minimum from the type-C
receptacle to the TPS25810 on CC1 and CC2.
– 10-uF output cap should be placed near Type-C receptacle
– Refer to the TPS25810EVM-745 Evaluation Module for an example of a double layer board that passes
IEC61000-4-2 testing
– Do not create stubs or test points on the CC lines. Keep the traces short if possible and use minimal via
along the traces (1-2 inches or less).
– Refer to ESD Protection Layout Guide for additional information (TI Literature Number SLVA680)
28
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
TPS25810
www.ti.com
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
Layout Guidelines (continued)
– Have a dedicated ground plane layer if possible to avoid differential voltage buildup
10.2 Layout Example
Top Layer Signal Trace
Top Layer Signal Ground Plane
Bottom Layer Signal Trace
Bottom Layer Signal Ground Plane
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
Via to Bottom Layer Signal Ground Plane
Via to Bottom Layer Signal
/AUDIO
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
18
17
/DEBUG
/POL
/UFP
/LD_DET
/FAULT
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
AUX
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
19
20
1
16
2
15
Thermal
Pad
IN1
3
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
OUT
14
4
13
CC2
AUX
5
12
GND
EN
6
11
CC1
IN2
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
10 REF
CHG_HI
CHG
9 REF_RTN
8
7
Signal Ground
Top Layer
Signal Ground
Bottom Layer
Figure 29. Layout Example
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
29
TPS25810
SLVSCR1C – SEPTEMBER 2015 – REVISED JULY 2017
www.ti.com
11 Device and Documentation Support
11.1 Device Support
11.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
11.2 Documentation Support
11.2.1 Related Documentation
PowerPad™ Thermally Enhanced Package (TI literature Number SLMA002)
PowerPAD™ Made Easy (TI Literature Number SLMA004)
TPS25810EVM-745 User's Guide (SLVUAI0)
Protecting the TPS25810 from High Voltage DFPs (SLVA751)
11.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.5 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.6 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
30
Submit Documentation Feedback
Copyright © 2015–2017, Texas Instruments Incorporated
Product Folder Links: TPS25810
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
TPS25810RVCR
ACTIVE
WQFN
RVC
20
3000
RoHS & Green NIPDAU | NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
25810
TPS25810RVCT
ACTIVE
WQFN
RVC
20
250
RoHS & Green
Level-2-260C-1 YEAR
-40 to 125
25810
NIPDAU
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of