TPS53126EVM-600

www.ti.com Table of Contents User’s Guide TPS53126 Buck Controller Evaluation Module User's Guide ABSTRACT The TPS53126EVM-600 Evaluation Module presents an easy-to-use reference design for a common, dualoutput power supply using the TPS53126 controller in cost-sensitive applications. Table of Contents 1 Introduction.............................................................................................................................................................................3 1.1 Description......................................................................................................................................................................... 3 1.2 Applications........................................................................................................................................................................3 1.3 Features............................................................................................................................................................................. 3 2 Electrical Performance Specifications................................................................................................................................. 4 3 Schematic................................................................................................................................................................................5 4 Connector and Test Point Descriptions................................................................................................................................6 4.1 Enable Switches – SW1 and SW2..................................................................................................................................... 6 4.2 Switching Frequency Select Switch – SW3....................................................................................................................... 6 4.3 Test Point Descriptions.......................................................................................................................................................6 5 Test Setup................................................................................................................................................................................8 5.1 Equipment.......................................................................................................................................................................... 8 5.2 Recommended Setup........................................................................................................................................................ 8 6 Test Procedure...................................................................................................................................................................... 10 6.1 Start-up Procedure...........................................................................................................................................................10 6.2 Line/Load Regulation and Efficiency Measurement Procedure....................................................................................... 10 6.3 Output Ripple Voltage Measurement Procedure..............................................................................................................10 6.4 Shutdown Procedure........................................................................................................................................................10 7 Performance Data and Typical Characteristic Curves.......................................................................................................11 7.1 Efficiency.......................................................................................................................................................................... 11 7.2 Line and Load Regulation................................................................................................................................................ 12 7.3 Output Voltage Ripple...................................................................................................................................................... 13 7.4 Switch Node Waveforms.................................................................................................................................................. 14 8 EVM Assembly Drawings and Layout.................................................................................................................................15 9 Bill of Materials..................................................................................................................................................................... 18 10 Revision History................................................................................................................................................................. 19 List of Figures Figure 3-1. TPS53126EVM-600 Schematic.................................................................................................................................5 Figure 4-1. Tip and Barrel Measurement for Output Voltage Ripple............................................................................................7 Figure 5-1. TPS53126EVM-600 Recommended Test Setup....................................................................................................... 9 Figure 7-1. Efficiency vs Load (VIN = 8 V–22 V, VOUT1 = 1.05 V, IOUT1 = 0 A–4 A)....................................................................11 Figure 7-2. Efficiency vs Load (VIN = 8 V–22 V, VOUT2 = 1.8 V, IOUT2 = 0 A–4 A)......................................................................11 Figure 7-3. Output Voltage vs Load (VIN = 8 V–22 V, VOUT1 = 1.05 V, IOUT1 = 0 A–4 A)........................................................... 12 Figure 7-4. Output Voltage vs Load (VIN = 8 V–22 V, VOUT2 = 1.8 V, IOUT2 = 0 A–4 A)............................................................. 12 Figure 7-5. Output Voltage Ripple (VIN = 12 V, VOUT1 = 1.05 V, IOUT1 = 4 A, FSW = 350 kHz).................................................. 13 Figure 7-6. Output Voltage Ripple (VIN = 12 V, VOUT2 = 1.8 V, IOUT2 = 4 A, FSW = 350 kHz).................................................... 13 Figure 7-7. Switching Waveform (VIN = 12 V, VOUT1 = 1.05 V, IOUT1 = 4 A, FSW = 350 kHz).....................................................14 Figure 7-8. Switching Waveform (VIN = 12 V, VOUT2 = 1.08 V, IOUT2 = 4 A, FSW = 350 kHz).....................................................14 Figure 8-1. Top Assembly.......................................................................................................................................................... 15 Figure 8-2. Bottom Assembly.................................................................................................................................................... 15 Figure 8-3. Top Layer.................................................................................................................................................................16 Figure 8-4. Bottom Layer........................................................................................................................................................... 16 SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 TPS53126 Buck Controller Evaluation Module User's Guide Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated 1 Trademarks www.ti.com Figure 8-5. Internal Layer 1....................................................................................................................................................... 17 Figure 8-6. Internal Layer 2....................................................................................................................................................... 17 List of Tables Table 2-1. TPS53126EVM-600 Electrical and Performance Specifications.................................................................................4 Table 4-1. TPS53126EVM-600 Test Points Description.............................................................................................................. 6 Table 9-1. TPS53126EVM-600 Bill of Materials.........................................................................................................................18 Trademarks D-CAP2™ is a trademark of Texas Instruments. All trademarks are the property of their respective owners. 2 TPS53126 Buck Controller Evaluation Module User's Guide SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated www.ti.com Introduction 1 Introduction 1.1 Description The TPS53126EVM-600 evaluation board provides the user with a convenient way to evaluate the TPS53126 Dual D-CAP2™ Mode Control Step-Down Controller in a realistic, cost-sensitive application. Providing both a low core-type 1.05-V and I/O type 1.8-V output at up to 4 A from a loosely regulated 12-V (8-V to 22-V) source, the TPS53126EVM-600 includes switches and test points to assist users in evaluating the performance of the TPS53126 controller in their applications. 1.2 Applications • • • • Digital television Set-top box DSL and cable modems Cost-sensitive digital consumer products 1.3 Features • • • • • 8-V to 22-V input 1.05-V and 1.8-V output Up to 4 A per channel output Switch selectable 350-kHz or 700-kHz pseudo-fixed frequency D-CAP2™ mode control Independent enable switches for power-on/power-off testing SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 TPS53126 Buck Controller Evaluation Module User's Guide Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated 3 Electrical Performance Specifications www.ti.com 2 Electrical Performance Specifications Table 2-1. TPS53126EVM-600 Electrical and Performance Specifications Parameter Notes and Conditions Min Typ Max 8 12 22 Unit INPUT CHARACTERISTICS VIN Input voltage IIN Input Current VIN = 12 V, IOUT1 = 4 A, IOUT2 = 4 A – 1.2 1.5 No-Load Input Current VIN = 12 V, IOUT = 0 A, SW3 = 350 kHz – 20 – Input UVLO IOUT = 4 A 4.0 4.2 4.5 V V VIN_UVLO V A mA OUTPUT CHARACTERISTICS VOUT1 Output Voltage 1 VIN = 12 V, IOUT1 = 2 A – 1.05 – Line Regulation VIN = 8 V to 22 V – – 1% 1% Load Regulation IOUT1 = 0 A to 4 A – – VOUT1_rip Output Voltage Ripple VIN = 12 V, IOUT2 = 4 A – – IOUT1 Output Current 1 VIN = 8 V to 22 V 0 4 A VOUT2 Output Voltage 2 VIN = 12 V, IOUT2 = 2 A – 1.80 – V Line Regulation VIN = 8 V to 22 V – – 1% Load Regulation IOUT2 = 0 A to 4 A – – 1% VOUT2_rip Output Voltage Ripple VIN = 12 V, IOUT2 = 4 A – – IOUT2 Output Current 2 VIN = 8 V to 22 V 0 30 mVpp 30 mVpp 4 A SYSTEMS CHARACTERISTICS 4 FSW Switching Frequency SW3 = 350 kHz 200 350 ηpk1 Peak Efficiency of Output 1 η1 Full Load Efficiency of Output 1 VIN = 12 V, SW3 = 350 kHz – 88% VIN = 12 V, IOUT1 = 4 A, SW3 = 350 kHz – ηpk2 85% Peak Efficiency of Output 2 VIN = 12 V, SW3 = 350 kHz – 9%1 η2 Full Load efficiency of Output 2 VIN = 12 V, IOUT2 = 4 A, SW3 = 350 kHz – 91% TPS53126 Buck Controller Evaluation Module User's Guide 400 kHz SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated www.ti.com Schematic + + + 3 Schematic For Reference Only, See Table 9-1 for Specific Values Figure 3-1. TPS53126EVM-600 Schematic SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 TPS53126 Buck Controller Evaluation Module User's Guide Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated 5 Connector and Test Point Descriptions www.ti.com 4 Connector and Test Point Descriptions 4.1 Enable Switches – SW1 and SW2 TPS53126EVM-600 includes independent enable switches for each of the two outputs. When the switch is in the DIS position, the channel is disabled and discharged per the TPS53126’s internal discharge characteristics. To enable VOUT1, place SW1 in the EN position. To enable VOUT2, place SW2 in the EN position. 4.2 Switching Frequency Select Switch – SW3 TPS53126EVM-600 includes a frequency select switch (SW3) to select the frequency programmed by the TEST2 IC pin of the TPS53126. When in the 350-kHz position, the D-CAP2™ mode control selects the Ton for 350-kHz operation. When in the 700-kHz position, the D-CAP2™ mode control selects the Ton for 700-kHz operation. For more details of switching frequency verse VIN and IOUT, see the TPS53126 data sheet . Do not switch the position of SW3 while the TPS53126EVM-600 module is running. To change frequency selection, disable both Channel 1 and Channel 2 before changing the switching frequency. 4.3 Test Point Descriptions Table 4-1 lists the test points, their labels, uses, and where additional information is located. Table 4-1. TPS53126EVM-600 Test Points Description Test Point Label Use TP1 TEST1 Not Used TP2 TEST2 Monitor Frequency Select Voltage (5 V or GND) TP3 GND Ground for Input Voltage Section 4.3.1 TP4 GND Ground for Channel-1 Output Voltage Section 4.3.2 TP5 SW1 Monitor Switching Node for Channel 1 Section 4.3.4 TP6 GND Ground for Channel-2 Output Voltage Section 4.3.3 TP7 VOUT2 Monitor Output Voltage for Channel 2 Section 4.3.3 TP8 VOUT1 Monitor Output Voltage for Channel 1 Section 4.3.2 Monitor Input Voltage Section 4.3.1 Monitor Output of VREG5 Regulator Section 4.3.5 Monitor Switching Node for Channel 2 Section 4.3.4 TP9 VIN TP10 VREG5 TP11 SW2 Section 4.3.1 Input Voltage Monitoring –TP3 and TP9 TPS53126EVM-600 provides two test points for measuring the voltage applied to the module. This allows the user to measure the actual module voltage without losses from input cables and connectors. Measure all input voltage between TP9 and TP3. To use TP9 and TP3, connect a voltmeter positive terminal to TP9 and negative terminal to TP3. 4.3.2 Channel-1 Output Voltage Monitoring – TP4 and TP8 TPS53126EVM-600 provides two test points for measuring the voltage generated at the VOUT1 output by the module. This allows the user to measure the actual output voltage without losses from output cables and connectors. Measure all dc output voltage measurements between TP8 and TP4. To use TP8 and TP4, connect a voltmeter positive terminal to TP8 and negative terminal to TP4. For output ripple measurements, TP8 and TP4 allow a user to limit the ground loop area by using the tip and barrel measurement technique shown in Figure 4-1. 6 TPS53126 Buck Controller Evaluation Module User's Guide SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated www.ti.com Connector and Test Point Descriptions Metal Ground Barrel Probe Tip TP8 TP4 Figure 4-1. Tip and Barrel Measurement for Output Voltage Ripple 4.3.3 Channel-2 Output Voltage Monitoring – TP6 and TP7 TPS53126EVM-600 provides two test points for measuring the voltage generated at the VOUT2 output by the module. This allows the user to measure the actual output voltage without losses from output cables and connectors. Measure all dc output voltage between TP7 and TP6. To use TP7 and TP6, connect a voltmeter positive terminal to TP7 and negative terminal to TP6. For output ripple measurements, TP7 and TP6 allow a user to limit the ground loop area by using the tip and barrel measurement technique shown in Figure 4-1. 4.3.4 Switching Node Monitoring – TP3, TP5, and TP11 TPS53126EVM-600 provides two test points for measuring the switching node waveform voltages. TP5 monitors the switching node of Channel 1. TP2 monitors the switching node of Channel 2. To use TP5 or TP11, connect an oscilloscope probe between TP5 or TP11 and TP3. 4.3.5 5-V Regulator Output Monitoring – TP3 and TP10 TPS53126EVM-600 provides a test point for measuring the output of the internal 5-V regulator. TP10 monitors the output voltage of the internal 5-V regulator. To use TP10, connect a voltmeter positive terminal to TP10 and negative terminal to TP3. SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 TPS53126 Buck Controller Evaluation Module User's Guide Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated 7 Test Setup www.ti.com 5 Test Setup 5.1 Equipment 5.1.1 Voltage Source The input voltage source (VIN) shall be a 0-V to 25-V variable dc source capable of supplying 3 Adc minimum. 5.1.2 Meters A1: 0-Adc to 5-Adc, ammeter V1: VIN, 0-V to 25-V voltmeter V2: VOUT1, 0-V to 2-V voltmeter V3: VOUT2, 0-V to 2-V voltmeter 5.1.3 Loads LOAD1: One output load is an electronic load set for constant-current mode capable of 0 Adc to 4 Adc at 1.05 Vdc. LOAD2: The other output load is an electronic load set for constant-current mode capable of 0 Adc to 4 Adc at 1.8 Vdc. 5.1.4 Oscilloscope and Probe The oscilloscope, analog or digital, must be set for ac-coupled measurement with 20-MHz bandwidth limiting. Use 20-mV/division vertical resolution, 1-µs/division horizontal resolution for output ripple voltage test. Oscilloscope probes with exposed conductive ground barrels are recommended. 5.1.5 Recommended Wire Gauge VIN to J3 – The connection between the source voltage VIN and J1 of TPS53126EVM-600 can carry as much as 2 Adc. The minimum recommended wire size is AWG 16 with the total length of wire less than 2 feet (1-foot input, 1-foot return). J1 to LOAD1 and J2 to LOAD2 – The connection between J1 and LOAD1, and J2 and LOAD2 of TPS53126EVM-600 can carry as much as 4 Adc each. The minimum recommended wire size is AWG 14 with the total length of wire less than 2 feet (1-foot input, 1-foot return). 5.1.6 Other Test Equipment FAN – The TPS53126EVM-600 evaluation module includes components that can get hot to touch. Because this EVM is not enclosed to allow probing of circuit nodes, a small fan capable of 200-400 lfm is recommended to reduce component temperatures when operating. 5.2 Recommended Setup Figure 5-1 shows the recommended test setup to evaluate the TPS53126EVM-600. Working at an ESD workstation, ensure that any wrist straps, bootstraps, or mats are connected referencing the user to earth ground before power is applied to the EVM. An electrostatic smock and safety glasses also are recommended. 8 TPS53126 Buck Controller Evaluation Module User's Guide SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated www.ti.com Test Setup FAN + V1 - + - + + A1 + LOAD1 1.05V @ 4A V2 LOAD2 1.8 V @ 4A V3 - + VVIN Figure 5-1. TPS53126EVM-600 Recommended Test Setup SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 TPS53126 Buck Controller Evaluation Module User's Guide Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated 9 Test Procedure www.ti.com 6 Test Procedure 6.1 Start-up Procedure 1. Prior to connecting the dc input source VIN, it is advisable to limit the source current from VIN to 2 Adc maximum. Ensure that VIN is initially set to 0 V. 2. Ensure LOAD1 and LOAD2 are set to constant-current mode to sink 0 A before VIN is applied. 3. Verify SW1, SW2, and SW3 are in the desired position. 4. Place a fan as shown in Figure 5-1 and turn on, making sure air is flowing across the EVM. 5. Increase VIN from 0 V to 12 Vdc. 6.2 Line/Load Regulation and Efficiency Measurement Procedure 1. 2. 3. 4. 5. 6. Set up TPS53126EVM-600 per Section 5.2. Start up the TPS53126EVM-600 per Section 6.1. Adjust VIN to desired value between 8 Vdc and 22 Vdc. Adjust LOAD1/LOAD2 to desired load between 0 Adc and 4 Adc. Read input voltage, output voltage, and input current from V1, V2/V3, and A1, respectively. Shut down the TPS53126EVM-600 per Section 6.4. 6.3 Output Ripple Voltage Measurement Procedure 1. 2. 3. 4. 5. Set up the TPS53126EVM-600 per Section 5.2. Start up the TPS53126EVM-600 per Section 6.1. Adjust VIN to desired value between 8 Vdc and 22 Vdc. Adjust LOAD1/LOAD2 to desired load between 0 A and 4 Adc. Connect the oscilloscope probe to TP8 and TP4 for VOUT1, or TP7 and TP6 for VOUT2 as shown in Figure 4-1. 6. Measure output ripple. 7. Shut down TPS53126EVM-600 per Section 6.4. 6.4 Shutdown Procedure 1. 2. 3. 4. 5. 6. 10 Set SW1 to DIS. Set SW2 to DIS. Decrease LOAD1 to 0 A, and shut down LOAD1. Decrease LOAD2 to 0 A, and shut down LOAD2. Decrease VIN to 0 V, and shut down VIN. Shut down the fan. TPS53126 Buck Controller Evaluation Module User's Guide SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated www.ti.com Performance Data and Typical Characteristic Curves 7 Performance Data and Typical Characteristic Curves Figure 7-1 through Figure 7-8 present typical performance curves for the TPS53126EVM-600. Because actual performance data can be affected by measurement techniques and environmental variables, these curves are presented for reference and may differ from actual field measurements. 7.1 Efficiency 95 95 VIN = 12 V VIN = 22 V VIN = 12 V VIN = 8 V 90 90 85 85 h - Efficiency - % h - Efficiency - % VIN = 8 V 80 75 VIN = 22 V 80 75 70 70 65 65 60 60 0 0.5 1 1.5 2 2.5 3 ILOAD - Load Current - A 3.5 4 4.5 0 0.5 1 (a) FSW = 350 kHz 1.5 2 2.5 3 ILOAD - Load Current - A 3.5 4 4.5 4 4.5 (b) FSW = 700 kHz Figure 7-1. Efficiency vs Load (VIN = 8 V–22 V, VOUT1 = 1.05 V, IOUT1 = 0 A–4 A) 95 95 90 90 85 h - Efficiency - % h - Efficiency - % 85 VIN = 12 V 80 VIN = 22 V 75 VIN = 8 V 80 VIN = 12 V 75 VIN = 8 V 70 70 65 65 60 VIN = 22 V 60 0 0.5 1 1.5 2 2.5 3 ILOAD - Load Current - A (a) FSW = 350 kHz 3.5 4 4.5 0 0.5 1 1.5 2 2.5 3 ILOAD - Load Current - A 3.5 (a) FSW = 700 kHz Figure 7-2. Efficiency vs Load (VIN = 8 V–22 V, VOUT2 = 1.8 V, IOUT2 = 0 A–4 A) SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 TPS53126 Buck Controller Evaluation Module User's Guide Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated 11 Performance Data and Typical Characteristic Curves www.ti.com 7.2 Line and Load Regulation 1.07 1.07 VIN = 12 V VIN = 22 V 1.065 1.065 1.06 1.06 VIN = 12 V VOUT - Output Voltage - V VOUT - Output Voltage - V VIN = 8 V 1.055 1.05 VIN = 8 V 1.045 1.04 VIN = 22 V 1.055 1.05 1.045 1.04 1.035 1.035 1.03 1.03 0 0.5 1 1.5 2 2.5 3 ILOAD - Load Current - A 3.5 4 0 4.5 0.5 1 1.5 2 2.5 3 ILOAD - Load Current - A 3.5 4 4.5 4 4.5 (a) FSW = 700 kHz (a) FSW = 350 kHz Figure 7-3. Output Voltage vs Load (VIN = 8 V–22 V, VOUT1 = 1.05 V, IOUT1 = 0 A–4 A) 1.84 1.84 VIN = 22 V 1.83 VIN = 12 V 1.82 VOUT - Output Voltage - V VOUT - Output Voltage - V 1.83 1.81 1.8 VIN = 8 V 1.79 1.78 1.82 VIN = 8 V VIN = 12 V VIN = 22 V 1.81 1.8 1.79 1.78 1.77 1.77 1.76 1.76 0 0.5 1 1.5 2 2.5 3 ILOAD - Load Current - A 3.5 (a) FSW = 350 kHz 4 4.5 0 0.5 1 1.5 2 2.5 3 ILOAD - Load Current - A 3.5 (b) FSW = 700 kHz Figure 7-4. Output Voltage vs Load (VIN = 8 V–22 V, VOUT2 = 1.8 V, IOUT2 = 0 A–4 A) 12 TPS53126 Buck Controller Evaluation Module User's Guide SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated www.ti.com Performance Data and Typical Characteristic Curves 7.3 Output Voltage Ripple TPS53126EVM-600 Test condition: Vin 12 V; Vo 1 1.05; 4A; 350 kHz Output Ripple Figure 7-5. Output Voltage Ripple (VIN = 12 V, VOUT1 = 1.05 V, IOUT1 = 4 A, FSW = 350 kHz) TPS53126EVM-600 Test condition: Vin 12 V; Vo 2 1.8; 4A; 350 kHz Output Ripple Figure 7-6. Output Voltage Ripple (VIN = 12 V, VOUT2 = 1.8 V, IOUT2 = 4 A, FSW = 350 kHz) SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 TPS53126 Buck Controller Evaluation Module User's Guide Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated 13 Performance Data and Typical Characteristic Curves www.ti.com 7.4 Switch Node Waveforms TPS53126EVM-600 Test condition: Vin 12 V; Vo 1 1.05; 4A; 350 kHz Switch Node Figure 7-7. Switching Waveform (VIN = 12 V, VOUT1 = 1.05 V, IOUT1 = 4 A, FSW = 350 kHz) TPS53126EVM-600 Test condition: Vin 12 V; Vo 2 1.8 V; 4A; 350 kHz Switch Node Figure 7-8. Switching Waveform (VIN = 12 V, VOUT2 = 1.08 V, IOUT2 = 4 A, FSW = 350 kHz) 14 TPS53126 Buck Controller Evaluation Module User's Guide SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated www.ti.com EVM Assembly Drawings and Layout 8 EVM Assembly Drawings and Layout The following figures (Figure 8-1 through Figure 8-6) show the design of the TPS53126EVM-600 printed-circuit board (PCB). The EVM has been designed using a 4-layer, 2-oz copper-clad circuit board of 3.5 inch by 2.7 inch to allow the user to easily view, probe, and evaluate the TPS53126 control integrated circuit in a practical application. Moving components to both sides of the PCB or using additional internal layers can offer additional size reduction for space constrained systems. Figure 8-1. Top Assembly Figure 8-2. Bottom Assembly SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 TPS53126 Buck Controller Evaluation Module User's Guide Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated 15 EVM Assembly Drawings and Layout www.ti.com Figure 8-3. Top Layer Figure 8-4. Bottom Layer 16 TPS53126 Buck Controller Evaluation Module User's Guide SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated www.ti.com EVM Assembly Drawings and Layout Figure 8-5. Internal Layer 1 Figure 8-6. Internal Layer 2 SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 TPS53126 Buck Controller Evaluation Module User's Guide Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated 17 Bill of Materials www.ti.com 9 Bill of Materials The reference designators refer to the schematic in Figure 3-1 and assembly locations in Figure 8-1 and Figure 8-2. Components with a quantity of 0 listed are not populated on the PCB but are provided for reference. Table 9-1. TPS53126EVM-600 Bill of Materials Qty 18 RefDes Value Size Part Number MFR 0 C1 Capacitor, Aluminum, 25V, 20% 0.328 x 0.390 inch Std Std 0 C12, C19, C20, C21 Capacitor, Ceramic 0603 Std Std 1 C15 4.7 µF Capacitor, Ceramic, 10V, X5R, 20% 0805 Std Std 1 C16 1 µF Capacitor, Ceramic, 16V, X5R, 20% 0805 Std Std 4 C2, C3, C4, C5 10 µF Capacitor, Ceramic, 25V, X5R, 20% 1210 Std Std 0 C22, C24 Capacitor, Ceramic, 25V, X7R, 20% 0603 Std Std 1 C23 1000 pF Capacitor, Ceramic, Low Inductance, 16V, X7R, 20% 0603 Std Std 2 C6, C11 0.1 µF Capacitor, Ceramic, 50V, X5R, 10% 0603 Std Std 6 C7, C9, C10, C14, C17, C18 47 µF Capacitor, Ceramic, 6.3V, X5R, 20% 1206 Std Std 0 C8, C13 330 µF Capacitor, PXE, 4.0V, 15-mΩ, 20% 7343 (D) APXE4R0ARA331MF61G NIPPON CHEMI-CON 2 D1, D2 BAT54XV2T1G Diode, Schottky, 200 mA, 30 V SOD523 BAT54XV2T1G On Semi 3 J1, J2, J3 ED120/2DS Terminal Block, 2-pin, 15-A, 5.1mm 0.40 x 0.35 inch ED120/2DS OST 2 L1, L2 3.3 µH Inductor, SMT Chip Coil, ±30% 8 x 8mm LQH88PN3R3N38 Murata 4 Q1, Q2, Q3, Q4 CSD17507Q5A MOSFET, N-Chan, 30V, 65A, 11.8mΩ QFN-8 POWER CSD17507Q5A TI 1 R1 1.40k Resistor, Chip, 1/16W, 1% 0603 Std Std 2 R11, R12 5.11 Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R13 332 Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R14 0 Resistor, Chip, 1/16W, 5% 0603 Std Std 0 R15, R16 Resistor, Chip, 1/8W, 5% 0603 Std Std 2 R17, R18 Resistor, Chip, 1/16W, 1% 0603 Std Std 0 R2, R7, R9 Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R3 3.32k Resistor, Chip, 1/16W, 1% 0603 Std Std 4 R4, R6, R8, R10 10.0k Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R5 12.1k Resistor, Chip, 1/16W, 1% 0603 Std Std 3 SW1, SW2, SW3 G12AP-RO Switch, ON-ON Mini Toggle 0.28 x 0.18" G12AP-RO Nikkai 4 TP1, TP2, TP5, TP11 5012 Test Point, White, Thru Hole 0.125 x 0.125 inch 5012 Keystone 1 TP10 5013 Test Point, Orange, Thru Hole 0.125 x 0.125 inch 5013 Keystone 3 TP3, TP4, TP6 5011 Test Point, Black, Thru Hole 0.125 x 0.125 inch 5011 Keystone 2 TP7, TP8 5014 Test Point, Yellow, Thru Hole 0.125 x 0.125 inch 5014 Keystone 1 TP9 5010 Test Point, Red, Thru Hole 0.125 x 0.125 inch 5010 Keystone 1 U1 TPS53126RGET IC, Dual Synchronous Step-Down Controller for Low-Voltage Power Rails QFN-24 TPS53126RGET TI 1 – PCB, 2.70" x 3.50" x 0.063" FR-4 2.7" x 3.5" HPA600 Any 2.00 Description TPS53126 Buck Controller Evaluation Module User's Guide SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated www.ti.com Revision History 10 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision * (February 2011) to Revision A (January 2022) Page • Updated the numbering format for tables, figures, and cross-references throughout the document. ................3 • Updated the user's guide title............................................................................................................................. 3 SLVU435A – FEBRUARY 2011 – REVISED JANUARY 2022 TPS53126 Buck Controller Evaluation Module User's Guide Submit Document Feedback Copyright © 2022 Texas Instruments Incorporated 19 IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2022, Texas Instruments Incorporated