Order
Now
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
UCC27212
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
UCC27212 120-V Boot, 4-A Peak, High-Frequency Half-Bridge Driver
1 Features
3 Description
•
•
•
•
•
•
•
•
•
•
The UCC27212 device has a peak output current of
4-A source and 4-A sink, which allows for the ability
to drive large power MOSFETs. The device features
an on-chip 120-V rated bootstrap diode eliminating
the need for external discrete diodes. The input
structure can directly handle –10 V, which increases
robustness and is also independent of supply voltage.
The UCC27212 offers 5 V UVLO which helps lower
power losses and increased input hysteresis that
allows for interface to analog or digital PWM
controllers with enhanced noise immunity. The
switching node of the UCC27212 (HS pin) can handle
–18-V maximum, which allows the high-side channel
to be protected from inherent negative voltages.
1
4-A Sink, 4-A Source Output Currents
Maximum Boot Voltage 120-V DC
7-V to 17-V VDD Operating Range
20-V ABS Maximum VDD Operating Range
5-V Turn-off Under Voltage Lockout (UVLO)
Input Pins Can Tolerate –10 V to +20 V
7.2-ns Rise and 5.5-ns Fall Time (1000-pF Load)
20-ns Typical Propagation Delay
4-ns Typical Delay Matching
Specified from –40°C to +140°C
2 Applications
•
•
•
•
DC-DC Power Supplies
Merchant Telecom Rectifiers
Half-Bridge and Full-Bridge Converters
Push-Pull and Active-Clamp Forward Converters
Typical Application Diagram
12 V
Device Information(1)
PART NUMBER
UCC27212
Propagation Delays vs Supply Voltage T = 25°C
32
100 V
CONTROL
LI
DRIVE
HI
SECONDARY
SIDE
CIRCUIT
HS
LO
DRIVE
LO
UCC27212
ISOLATION
AND
FEEDBACK
Propagation Delay (ns)
HB
PWM
CONTROLLER
TDLRR
TDLFF
TDHRR
TDHFF
28
HO
BODY SIZE (NOM)
4.0 mm x 4.0 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
VDD
HI
PACKAGE
WSON (10)
24
20
16
12
8
4
0
8
Copyright © 2017, Texas Instruments Incorporated
12
16
Supply Voltage (V)
20
D001
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
UCC27212
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
6.1
6.2
6.3
6.4
6.5
6.6
6.7
7
1
1
1
3
4
5
Absolute Maximum Ratings ...................................... 5
ESD Ratings ............................................................ 5
Recommended Operating Conditions....................... 6
Thermal Information .................................................. 6
Electrical Characteristics........................................... 6
Switching Characteristics .......................................... 7
Typical Characteristics ............................................ 10
Detailed Description ............................................ 13
7.1 Overview ................................................................. 13
7.2 Functional Block Diagram ....................................... 14
7.3 Feature Description................................................. 14
2
7.4 Device Functional Modes........................................ 15
8
Application and Implementation ........................ 16
8.1 Application Information............................................ 16
8.2 Typical Application ................................................. 16
9 Power Supply Recommendations...................... 20
10 Layout................................................................... 21
10.1 Layout Guidelines ................................................. 21
10.2 Layout Example .................................................... 22
11 Device and Documentation Support ................. 23
11.1
11.2
11.3
11.4
11.5
11.6
Documentation Support .......................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
23
23
23
23
23
23
12 Mechanical, Packaging, and Orderable
Information ........................................................... 23
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
UCC27212
www.ti.com
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (June 2017) to Revision A
Page
•
Changed " 5-V to 17-V VDD Operating Range, (20-V ABS Maximum)" to "7-V to 17-V VDD Operating Range, (20-V
ABS Maximum)" ..................................................................................................................................................................... 1
•
Changed extended output pulse from 325-ns MAX to 325-ns TYP. ..................................................................................... 8
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
3
UCC27212
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
www.ti.com
5 Pin Configuration and Functions
DPR Package
SON-10
Top View
VDD
1
HB
2
10
3RZHU3$' Œ
LO
9
VSS
8
LI
HO
3
HS
4
7
HI
N/C
5
6
N/C
Not to scale
Pin Functions
PIN
(1)
(2)
(3)
4
I/O
DESCRIPTION
NO.
NAME
2
HB
P
High-side bootstrap supply. The bootstrap diode is on-chip but the external bootstrap
capacitor is required. Connect positive side of the bootstrap capacitor to this pin. Typical
range of HB bypass capacitor is 0.022 µF to 0.1 µF.
7
HI
I
High-side input. (1)
3
HO
O
High-side output. Connect to the gate of the high-side power MOSFET.
4
HS
P
High-side source connection. Connect to source of high-side power MOSFET. Connect the
negative side of bootstrap capacitor to this pin.
8
LI
I
Low-side input. (1)
10
LO
O
Low-side output. Connect to the gate of the low-side power MOSFET.
5
N/C
—
No internal connection.
6
N/C
—
No internal connection.
Pad
PowerPAD
™ (2)
G
Used on the DDA, DRM and DPR packages only. Electrically referenced to VSS (GND).
Connect to a large thermal mass trace or GND plane to dramatically improve thermal
performance.
1
VDD
P
Positive supply to the lower-gate driver. Decouple this pin to VSS (GND). Typical decoupling
capacitor range is 0.22 µF to 4.7 µF. (3)
9
VSS
G
Negative supply terminal for the device which is generally grounded.
For cold temperature applications TI recommends the upper capacitance range. Follow the Layout Guidelines for PCB layout.
The thermal pad is not directly connected to any leads of the package; however, it is electrically and thermally connected to the
substrate which is the ground of the device.
HI or LI input is assumed to connect to a low impedance source signal. The source output impedance is assumed less than 100 Ω. If the
source impedance is greater than 100 Ω, add a bypassing capacitor, each, between HI and VSS and between LI and VSS. The added
capacitor value depends on the noise levels presented on the pins, typically from 1 nF to 10 nF should be effective to eliminate the
possible noise effect. When noise is present on two pins, HI or LI, the effect is to cause HO and LO malfunctions to have wrong logic
outputs.
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
UCC27212
www.ti.com
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
VDD (2), VHB – VHS
Supply voltage range
VLI, VHI
Input voltages on LI and HI
Output voltage on LO
VHO
Output voltage on HO
VHS
Voltage on HS
VHB
TJ
20
V
V
–2
VDD + 0.3
V
VHS – 0.3
VHB + 0.3
V
VHS – 2
VHB + 0.3
V
Repetitive pulse < 100
ns (3)
–1
100
V
–(24 V –
VDD)
115
V
Voltage on HB
–0.3
120
V
Operating virtual junction temperature range
–40
150
°C
–65
150
°C
Repetitive pulse < 100
ns (3)
Storage temperature, Tstg
(2)
(3)
V
VDD + 0.3
DC
(1)
UNIT
20
–10
Repetitive pulse < 100
ns (3)
DC
MAX
–0.3
DC
VLO
MIN
–0.3
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to VSS unless otherwise noted. Currents are positive into and negative out of the specified terminal.
Verified at bench characterization. VDD is the value used in an application design.
6.2 ESD Ratings
VALUE
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001
V(ESD)
(1)
(2)
Electrostatic discharge
(1)
Charged-device model (CDM), per JEDEC specification JESD22C101 (2)
UNIT
±2000
±1500
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
5
UCC27212
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
www.ti.com
6.3 Recommended Operating Conditions
over operating free-air temperature range, all voltages are with respect to VSS; currents are positive into and negative out of
the specified terminal. –40°C < TJ = TA < 140°C (unless otherwise noted)
VDD
Supply voltage range, VHB – VHS
VHS
Voltage on HS
VHS
Voltage on HS (repetitive pulse < 100 ns)
VHB
Voltage on HB
MIN
NOM
MAX
7
12
17
UNIT
V
–1
100
V
–(20 V – VDD)
110
V
VHS + 8
115
V
50
V/ns
140
°C
Voltage slew rate on HS
Operating junction temperature
–40
6.4 Thermal Information
UCC27212
THERMAL METRIC (1)
DPR (SON)
UNIT
10 PINS
RθJA
Junction-to-ambient thermal resistance
36.8
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
36.0
°C/W
RθJB
Junction-to-board thermal resistance
14.0
°C/W
ψJT
Junction-to-top characterization parameter
0.3
°C/W
ψJB
Junction-to-board characterization parameter
14.2
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
3.4
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Electrical Characteristics
over operating free-air temperature range, VHS = VSS = 0 V, no load on LO or HO, TA = TJ = –40°C to +140°C, (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
0.05
0.085
0.17
mA
2.1
2.5
6.5
mA
0.015
0.065
0.1
mA
1.5
2.5
5.1
mA
SUPPLY CURRENTS, VDD = VHB = 12 V
IDD
VDD quiescent current
V(LI) = V(HI) = 0 V
IDDO
VDD operating current
f = 500 kHz, CLOAD = 0
IHB
Boot voltage quiescent current
V(LI) = V(HI) = 0 V
IHBO
Boot voltage operating current
f = 500 kHz, CLOAD = 0
IHBS
HB to VSS quiescent current
V(HS) = V(HB) = 115 V
IHBSO
HB to VSS operating current
f = 500 kHz, CLOAD = 0
0.0005
1
µA
0.07
1.2
mA
0.02
0.065
0.14
mA
2.1
2.5
6.5
mA
0.01
0.04
0.08
mA
mA
SUPPLY CURRENTS, VDD = VHB = 6.8 V
IDD
VDD quiescent current
V(LI) = V(HI) = 0 V
IDDO
VDD operating current
f = 500 kHz, CLOAD = 0
IHB
Boot voltage quiescent current
V(LI) = V(HI) = 0 V
IHBO
Boot voltage operating current
f = 500 kHz, CLOAD = 0
IHBS
HB to VSS quiescent current
V(HS) = V(HB) = 115 V
IHBSO
HB to VSS operating current
f = 500 kHz, CLOAD = 0
1.5
2.5
5.1
0.0005
1
µA
0.07
1.2
mA
V
INPUT, VDD = VHB = 12 V
VHIT
Input voltage threshold
1.7
2.3
2.55
VLIT
Input voltage threshold
1.2
1.6
1.9
VIHYS
Input voltage hysteresis
RIN
Input pulldown resistance
V
700
mV
68
kΩ
INPUT, VDD = VHB = 6.8 V
VHIT
Input voltage threshold
1.6
2.0
2.6
V
VLIT
Input voltage threshold
1.1
1.5
2.1
V
6
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
UCC27212
www.ti.com
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
Electrical Characteristics (continued)
over operating free-air temperature range, VHS = VSS = 0 V, no load on LO or HO, TA = TJ = –40°C to +140°C, (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
VIHYS
Input voltage hysteresis
RIN
Input pulldown resistance
MIN
TYP
MAX
UNIT
500
mV
68
kΩ
UNDER-VOLTAGE LOCKOUT (UVLO), VDD = VHB = 12 V
VDDR
VDD turnon threshold
VDDHYS
Hysteresis
VHBR
VHB turnon threshold
VHBHYS
Hysteresis
4.9
5.7
6.4
V
0.4
4.35
5.3
V
6.3
V
0.3
V
BOOTSTRAP DIODE, VDD = VHB = 12 V
VF
Low-current forward voltage
IVDD-HB = 100 µA
0.65
0.8
VFI
High-current forward voltage
IVDD-HB = 100 mA
0.85
0.95
V
RD
Dynamic resistance, ΔVF/ΔI
IVDD-HB = 100 mA and 80 mA
0.5
0.85
Ω
0.3
V
BOOTSTRAP DIODE, VDD = VHB = 6.8 V
VF
Low-current forward voltage
IVDD-HB = 100 µA
0.65
0.8
V
VFI
High-current forward voltage
IVDD-HB = 100 mA
0.85
0.95
V
RD
Dynamic resistance, ΔVF/ΔI
IVDD-HB = 100 mA and 80 mA
0.5
0.85
Ω
0.3
LO GATE DRIVER, VDD = VHB = 12 V
VLOL
Low-level output voltage
0.05
0.1
0.19
V
VLOH
High level output voltage
0.1
0.16
0.29
V
Peak pullup current
(1)
Peak pulldown current
(1)
3.7
A
4.5
A
LO GATE DRIVER, VDD = VHB = 6.8 V
VLOL
Low-level output voltage
ILO = 100 mA
0.04
0.13
0.35
V
VLOH
High level output voltage
ILO = –100 mA, VLOH = VDD – VLO
0.12
0.23
0.42
V
Peak pullup current
VLO = 0 V
1.3
A
Peak pulldown current
VLO = 12 V for VDD = 6.8V
1.7
A
HO GATE DRIVER, VDD = VHB = 12 V
VHOL
Low-level output voltage
0.05
0.1
0.19
V
VHOH
High-level output voltage
0.1
0.16
0.29
V
Peak pullup current
(1)
Peak pulldown current
(1)
3.7
A
4.5
A
HO GATE DRIVER, VDD = VHB = 6.8 V
VLOL
Low-level output voltage
IHO = 100 mA
0.04
0.13
0.35
V
VLOH
High level output voltage
IHO = –100 mA, VHOH = VHB – VHO
0.12
0.23
0.42
V
Peak pullup current
VHO = 0 V
1.3
A
Peak pulldown current
VHO = 12 V for VDD = 6.8V
1.7
A
(1)
Ensured by design.
6.6 Switching Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
PROPAGATION DELAYS, VDD = VHB = 12 V
TDLFF
VLI falling to VLO falling
CLOAD = 0
10
16
30
ns
TDHFF
VHI falling to VHO falling
CLOAD = 0
10
16
30
ns
TDLRR
VLI rising to VLO rising
CLOAD = 0
10
20
42
ns
TDHRR
VHI rising to VHO rising
CLOAD = 0
10
20
42
ns
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
7
UCC27212
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
www.ti.com
Switching Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
PROPAGATION DELAYS, VDD = VHB = 6.8 V
TDLFF
VLI falling to VLO falling
CLOAD = 0
10
24
50
ns
TDHFF
VHI falling to VHO falling
CLOAD = 0
10
24
50
ns
TDLRR
VLI rising to VLO rising
CLOAD = 0
13
28
57
ns
TDHRR
VHI rising to VHO rising
CLOAD = 0
13
28
57
ns
TJ = 25°C
4
9.5
ns
TJ = –40°C to +140°C
4
17
ns
TJ = 25°C
4
9.5
ns
TJ = –40°C to +140°C
4
17
ns
TJ = 25°C
8
TJ = –40°C to +140°C
8
TJ = 25°C
6
TJ = –40°C to +140°C
6
DELAY MATCHING, VDD = VHB = 12 V
TMON
TMOFF
From HO OFF to LO ON
From LO OFF to HO ON
DELAY MATCHING, VDD = VHB = 6.8 V
TMON
From HO OFF to LO ON
TMOFF
From LO OFF to HO ON
ns
18
ns
ns
18
ns
OUTPUT RISE AND FALL TIME, VDD = VHB = 12 V
tR
LO rise time
CLOAD = 1000 pF, from 10% to 90%
7.8
ns
tR
HO rise time
CLOAD = 1000 pF, from 10% to 90%
7.8
ns
tF
LO fall time
CLOAD = 1000 pF, from 90% to 10%
6.0
ns
tF
HO fall time
CLOAD = 1000 pF, from 90% to 10%
6.0
ns
tR
LO, HO
CLOAD = 0.1 µF, (3 V to 9 V)
0.36
0.6
µs
tF
LO, HO
CLOAD = 0.1 µF, (9 V to 3 V)
0.20
0.4
µs
OUTPUT RISE AND FALL TIME, VDD = VHB = 6.8 V
tR
LO rise time
CLOAD = 1000 pF, from 10% to 90%
9.5
ns
tR
HO rise time
CLOAD = 1000 pF, from 10% to 90%
13.0
ns
tF
LO fall time
CLOAD = 1000 pF, from 90% to 10%
9.5
ns
tF
HO fall time
CLOAD = 1000 pF, from 90% to 10%
13.0
ns
tR
LO, HO
CLOAD = 0.1 µF, (30% to 70%)
0.45
0.7
µs
tF
LO, HO
CLOAD = 0.1 µF, (70% to 30%)
0.2
0.5
µs
100
ns
MISCELLANEOUS
Minimum input pulse width that changes the
output
Bootstrap diode turnoff time
(1) (2)
Extended output pulse
(1)
(2)
(3)
8
IF = 20 mA, IREV = 0.5 A
(3)
when VDD = VHB = 6.8 V, VHS =
100 V, and input pulse width is 100
ns
20
ns
325
ns
Ensured by design.
IF: Forward current applied to bootstrap diode, IREV: Reverse current applied to bootstrap diode.
Typical values for TA = 25°C.
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
UCC27212
www.ti.com
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
LI
Input
(HI, LI)
HI
TDLRR, TDHRR
LO
Output
(HO, LO)
TDLFF, TDHFF
HO
Figure 1. Timing Diagram
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
9
UCC27212
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
www.ti.com
6.7 Typical Characteristics
100
IDD Operating Current (mA)
Quiescent Current (µA)
100
80
60
40
20
10
1
CL = 0 pF, T = −40°C
CL = 0 pF, T = 25°C
CL = 0 pF, T = 140°C
CL = 1000 pF, T = 25°C
CL = 1000 pF, T = 140°C
CL = 4700 pF, T = 140°C
0.1
IDD
IHB
0
0
2
4
6
8
10
12
14
Supply Voltage (V)
16
18
0.01
20
T = 25°C
10
Figure 2. Quiescent Current vs Supply Voltage
Figure 3. IDD Operating Current vs Frequency
Boot Operating Current (mA)
IDD Operating Current (mA)
10
1
CL = 0 pF, T = −40°C
CL = 0 pF, T = 25°C
CL = 0 pF, T = 140°C
CL = 1000 pF, T = 25°C
CL = 1000 pF, T = 140°C
CL = 4700 pF, T = 140°C
0.1
10
100
Frequency (kHz)
10
1
0.1
0.01
1000
CL = 0 pF, T = −40°C
CL = 0 pF, T = 25°C
CL = 0 pF, T = 140°C
CL = 1000 pF, T = 25°C
CL = 1000 pF, T = 140°C
CL = 4700 pF, T = 140°C
10
5
5
Input Threshold Voltage (V)
6
4
3
2
1
0
Rising
Falling
8
1000
Figure 5. Boot Voltage Operating Current vs
Frequency (HB To HS)
6
−1
100
Frequency (kHz)
VHB – VHS = 12 V
Figure 4. IDD Operating Current vs Frequency
Input Threshold Voltage (V)
G002
100
VDD = 12 V
12
16
Supply Voltage (V)
20
4
3
2
1
0
Rising
Falling
−1
−40
−20
0
20
40
60
80
Temperature (°C)
100
120
140
VDD = 12 V
T = 25°C
Figure 6. Input Threshold vs Supply Voltage
10
1000
VDD = 12 V
100
0.01
100
Frequency (kHz)
Figure 7. Input Thresholds vs Temperature
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
UCC27212
www.ti.com
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
Typical Characteristics (continued)
0.2
VOL − LO/HO Output Voltage (V)
V OH – LO/HO Output Voltage (V)
0.32
0.28
0.24
0.2
0.16
0.12
VDD = VHB = 8 V
VDD = VHB = 12 V
VDD = VHB = 16 V
VDD = VHB = 20 V
0.08
0.04
0
−40
−20
0
20
40
60
80
Temperature (°C)
100
120
0.12
0.08
VDD = VHB = 8 V
VDD = VHB = 12 V
VDD = VHB = 16 V
VDD = VHB = 20 V
0.04
0
−40
140
IHO = ILO = 100 mA
0.16
−20
0
20
40
60
80
Temperature (°C)
100
120
140
IHO = ILO = 100 mA
Figure 8. LO and HO High-Level Output Voltage
vs Temperature
Figure 9. LO and HO Low-Level Output Voltage
vs Temperature
8
1.5
7.6
1.2
Hysteresis (V)
Threshold (V)
7.2
6.8
6.4
0.9
0.6
6
0.3
5.6
VDD Rising Threshold
HB Rising Threshold
5.2
−40
−20
0
20
40
60
80
Temperature (°C)
100
120
VDD UVLO Hysteresis
HB UVLO Hysteresis
0
−40
140
−20
0
G009
Figure 10. Undervoltage Lockout Threshold
vs Temperature
20
40
60
80
Temperature (°C)
100
120
140
G010
Figure 11. Undervoltage Lockout Threshold Hysteresis
vs Temperature
32
40
32
28
24
20
16
12
TDLRR
TDLFF
TDHRR
TDHFF
8
4
0
−40
−20
0
20
40
60
80
Temperature (°C)
100
120
140
VDD = VHB = 12 V
Propagation Delay (ns)
Propagation Delay (ns)
36
24
16
TDLRR
TDLFF
TDHRR
TDHFF
8
0
−40
−20
0
20
40
60
80
Temperature (°C)
100
120
140
VDD = VHB = 12 V
Figure 12. Propagation Delays vs Temperature
Figure 13. Propagation Delays vs Temperature
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
11
UCC27212
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
www.ti.com
32
32
28
28
24
20
16
12
TDLRR
TDLFF
TDHRR
TDHFF
8
4
0
8
12
16
Supply Voltage (V)
Propagation Delay (ns)
Propagation Delay (ns)
Typical Characteristics (continued)
24
20
16
12
TDLRR
TDLFF
TDHRR
TDHFF
8
4
0
20
8
T = 25°C
Figure 15. Propagation Delays vs Supply Voltage
(VDD = VHB)
10
5
Pulldown Current
Pullup Current
8
4
Output Current (A)
Delay Matching (ns)
20
T = 25°C
Figure 14. Propagation Delays vs Supply Voltage
(VDD = VHB)
6
4
2
0
−2
−40
12
16
Supply Voltage (V)
3
2
1
TMON
TMOFF
−20
0
20
40
60
80
Temperature (°C)
100
120
140
VDD = VHB = 12 V
0
0
2
4
6
8
Output Voltage (V)
10
12
G016
VDD = VHB = 12 V
Figure 16. Delay Matching vs Temperature
Figure 17. Output Current vs Output Voltage
100
Diode Current (mA)
10
1
0.1
0.01
0.001
500
550
600
650
700
750
Diode Voltage (mV)
800
850
G017
Figure 18. Diode Current vs Diode Voltage
12
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
UCC27212
www.ti.com
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
7 Detailed Description
7.1 Overview
The UCC27212 device represents Texas Instruments’ latest generation of high-voltage gate drivers, which are
designed to drive both the high-side and low-side of N-Channel MOSFETs in a half- and full-bridge or
synchronous-buck configuration. The floating high-side driver can operate with supply voltages of up to 120 V,
which allows for N-Channel MOSFET control in half-bridge, full-bridge, push-pull, two-switch forward, and active
clamp forward converters.
The UCC27212 device feature 4-A source and sink capability, industry best-in-class switching characteristics and
a host of other features listed in Table 1. These features combine to ensure efficient, robust and reliable
operation in high-frequency switching power circuits.
Table 1. UCC27212 Highlights
FEATURE
BENEFIT
4-A source and sink current with 0.9-Ω output resistance
High peak current ideal for driving large power MOSFETs with
minimal power loss (fast-drive capability at Miller plateau)
Input pins (HI and LI) can directly handle –10 VDC up to 20 VDC
Increased robustness and ability to handle undershoot and
overshoot can interface directly to gate-drive transformers without
having to use rectification diodes.
120-V internal boot diode
Provides voltage margin to meet telecom 100-V surge requirements
Switch node (HS pin) able to handle –18 V maximum for 100 ns
Allows the high-side channel to have extra protection from inherent
negative voltages caused by parasitic inductance and stray
capacitance
Robust ESD circuitry to handle voltage spikes
Excellent immunity to large dV/dT conditions
18-ns propagation delay with 7.2-ns rise time and 5.5-ns fall time
Best-in-class switching characteristics and extremely low-pulse
transmission distortion
2-ns (typical) delay matching between channels
Avoids transformer volt-second offset in bridge
Symmetrical UVLO circuit
Ensures high-side and low-side shut down at the same time
TTL optimized thresholds with increased hysteresis
Complementary to analog or digital PWM controllers; increased
hysteresis offers added noise immunity
In the UCC27212 device, the high side and low side each have independent inputs that allow maximum flexibility
of input control signals in the application. The boot diode for the high-side driver bias supply is internal to the
UCC27212. The UCC27212 is the TTL or logic compatible version. The high-side driver is referenced to the
switch node (HS), which is typically the source pin of the high-side MOSFET and drain pin of the low-side
MOSFET. The low-side driver is referenced to VSS, which is typically ground. The UCC27212 functions are
divided into the input stages, UVLO protection, level shift, boot diode, and output driver stages.
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
13
UCC27212
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
www.ti.com
7.2 Functional Block Diagram
2
HB
3
HO
4
HS
8
LO
7
VSS
UVLO
LEVEL
SHIFT
HI
VDD
5
1
UVLO
LI
6
Copyright © 2017, Texas Instruments Incorporated
7.3 Feature Description
7.3.1 Input Stages
The input stages provide the interface to the PWM output signals. The input stages of the UCC27212 device
have impedance of 70-kΩ nominal and input capacitance is approximately 2 pF. Pulldown resistance to VSS
(ground) is 70 kΩ. The logic level compatible input provides a rising threshold of 2.3 V and a falling threshold of
1.6 V. There is enough input hysteresis to avoid noise related jitter issues on the input.
7.3.2 Undervoltage Lockout (UVLO)
The bias supplies for the high-side and low-side drivers have UVLO protection. VDD as well as VHB to VHS
differential voltages are monitored. The VDD UVLO disables both drivers when VDD is below the specified
threshold. The rising VDD threshold is 5.7 V with 0.4-V hysteresis. The VHB UVLO disables only the high-side
driver when the VHB to VHS differential voltage is below the specified threshold. The VHB UVLO rising threshold is
5.3 V with 0.4 V hysteresis.
14
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
UCC27212
www.ti.com
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
Feature Description (continued)
7.3.3 Level Shift
The level shift circuit is the interface from the high-side input to the high-side driver stage which is referenced to
the switch node (HS). The level shift allows control of the HO output referenced to the HS pin and provides
excellent delay matching with the low-side driver.
7.3.4 Boot Diode
The boot diode necessary to generate the high-side bias is included in the UCC27212 family of drivers. The
diode anode is connected to VDD and cathode connected to VHB. With the VHB capacitor connected to HB and the
HS pins, the VHB capacitor charge is refreshed every switching cycle when HS transitions to ground. The boot
diode provides fast recovery times, low diode resistance, and voltage rating margin to allow for efficient and
reliable operation.
7.3.5 Output Stages
The output stages are the interface to the power MOSFETs in the power train. High slew rate, low resistance and
high peak current capability of both output drivers allow for efficient switching of the power MOSFETs. The lowside output stage is referenced from VDD to VSS and the high side is referenced from VHB to VHS.
7.4 Device Functional Modes
The device operates in normal mode and UVLO mode. See the Undervoltage Lockout (UVLO) section for
information on UVLO operation mode. In the normal mode the output state is dependent on states of the HI and
LI pins. Table 2 lists the output states for different input pin combinations.
Table 2. Device Logic Table
LI PIN
HO (1)
L
L
L
L
L
H
L
H
H
L
H
L
H
H
H
H
HI PIN
(1)
(2)
LO (2)
HO is measured with respect to HS.
LO is measured with respect to VSS.
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
15
UCC27212
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
To affect fast switching of power devices and reduce associated switching power losses, a powerful gate driver is
employed between the PWM output of controllers and the gates of the power semiconductor devices. Also, gate
drivers are indispensable when it is impossible for the PWM controller to directly drive the gates of the switching
devices. With the advent of digital power, this situation will be often encountered because the PWM signal from
the digital controller is often a 3.3-V logic signal which cannot effectively turn on a power switch. Level shifting
circuitry is needed to boost the 3.3-V signal to the gate-drive voltage (such as 12 V) in order to fully turn on the
power device and minimize conduction losses. Traditional buffer drive circuits based on NPN/PNP bipolar
transistors in totem-pole arrangement, being emitter follower configurations, prove inadequate with digital power
because they lack level-shifting capability. Gate drivers effectively combine both the level-shifting and buffer-drive
functions. Gate drivers also find other needs such as minimizing the effect of high-frequency switching noise by
locating the high-current driver physically close to the power switch, driving gate-drive transformers, and
controlling floating power-device gates, reducing power dissipation and thermal stress in controllers by moving
gate charge power losses from the controller into the driver.
Finally, emerging wide band-gap power device technologies such as GaN based switches, which are capable of
supporting very high switching frequency operation, are driving very special requirements in terms of gate drive
capability. These requirements include operation at low VDD voltages (5 V or lower), low propagation delays and
availability in compact, low-inductance packages with good thermal capability. Gate-driver devices are extremely
important components in switching power, and they combine the benefits of high-performance, low-cost
component count and board-space reduction as well as simplified system design.
8.2 Typical Application
12 V
100 V
VDD
HB
HI
LI
CONTROL
PWM
CONTROLLER
DRIVE
HI
SECONDARY
SIDE
CIRCUIT
HO
HS
LO
DRIVE
LO
UCC27212-Q1
ISOLATION
AND
FEEDBACK
Copyright © 2017, Texas Instruments Incorporated
Figure 19. UCC27212 Typical Application
16
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
UCC27212
www.ti.com
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
Typical Application (continued)
8.2.1 Design Requirements
For this design example, use the parameters listed in Table 3.
Table 3. Design Specifications
DESIGN PARAMETER
EXAMPLE VALUE
Supply voltage, VDD
12 V
Voltage on HS, VHS
0 V to 100 V
Voltage on HB, VHB
12 V to 112 V
Output current rating, IO
–4 A to 4 A
Operating frequency
500 kHz
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
17
UCC27212
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
www.ti.com
8.2.2 Detailed Design Procedure
8.2.2.1 Power Dissipation
Power dissipation of the gate driver has two portions as shown in Equation 1.
PDISS = PDC + PSW
(1)
Use Equation 2 to calculate the DC portion of the power dissipation (PDC).
PDC = IQ × VDD
where
•
IQ is the quiescent current for the driver.
(2)
The quiescent current is the current consumed by the device to bias all internal circuits such as input stage,
reference voltage, logic circuits, protections, and also any current associated with switching of internal devices
when the driver output changes state (such as charging and discharging of parasitic capacitances, parasitic
shoot-through, and so forth). The UCC27212 features very low quiescent currents (less than 0.17 mA, refer to
the table and contain internal logic to eliminate any shoot-through in the output driver stage. Thus the effect of
the PDC on the total power dissipation within the gate driver can be safely assumed to be negligible. The power
dissipated in the gate-driver package during switching (PSW) depends on the following factors:
• Gate charge required of the power device (usually a function of the drive voltage VG, which is very close to
input bias supply voltage VDD)
• Switching frequency
• Use of external gate resistors. When a driver device is tested with a discrete, capacitive load calculating the
power that is required from the bias supply is fairly simple. The energy that must be transferred from the bias
supply to charge the capacitor is given by Equation 3.
EG = ½CLOAD × VDD2
where
•
•
CLOAD is load capacitor
VDD is bias voltage feeding the driver
(3)
There is an equal amount of energy dissipated when the capacitor is charged and when it is discharged. This
leads to a total power loss given by Equation 4.
PG = CLOAD × VDD2 × fSW
where
•
fSW is the switching frequency
(4)
The switching load presented by a power MOSFET/IGBT is converted to an equivalent capacitance by examining
the gate charge required to switch the device. This gate charge includes the effects of the input capacitance plus
the added charge needed to swing the drain voltage of the power device as it switches between the ON and OFF
states. Most manufacturers provide specifications of typical and maximum gate charge, in nC, to switch the
device under specified conditions. Using the gate charge Qg, determine the power that must be dissipated when
switching a capacitor which is calculated using the equation QG = CLOAD × VDD to provide Equation 5 for power.
PG = CLOAD × VDD2 × fSW = QG × VDD × fSW
(5)
This power PG is dissipated in the resistive elements of the circuit when the MOSFET/IGBT is being turned on
and off. Half of the total power is dissipated when the load capacitor is charged during turnon, and the other half
is dissipated when the load capacitor is discharged during turnoff. When no external gate resistor is employed
between the driver and MOSFET/IGBT, this power is completely dissipated inside the driver package. With the
use of external gate-drive resistors, the power dissipation is shared between the internal resistance of driver and
external gate resistor.
18
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
UCC27212
www.ti.com
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
8.2.3 Application Curves
Figure 20. Negative 10-V Input
Figure 21. Step Input
Figure 22. Symmetrical UVLO
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
19
UCC27212
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
www.ti.com
9 Power Supply Recommendations
The bias supply voltage range for which the UCC27212 device is recommended to operate is from 7 V to 17 V.
The lower end of this range is governed by the internal undervoltage-lockout (UVLO) protection feature on the
VDD pin supply circuit blocks. Whenever the driver is in UVLO condition when the VDD pin voltage is below the
V(ON) supply start threshold, this feature holds the output low, regardless of the status of the inputs. The upper
end of this range is driven by the 20-V absolute maximum voltage rating of the VDD pin of the device (which is a
stress rating). Keeping a 3-V margin to allow for transient voltage spikes, the maximum recommended voltage for
the VDD pin is 17 V. The UVLO protection feature also involves a hysteresis function, which means that when the
VDD pin bias voltage has exceeded the threshold voltage and device begins to operate, and if the voltage drops,
then the device continues to deliver normal functionality unless the voltage drop exceeds the hysteresis
specification VDD(hys). Therefore, ensuring that, while operating at or near the 7 V range, the voltage ripple on the
auxiliary power supply output is smaller than the hysteresis specification of the device is important to avoid
triggering device shutdown. During system shutdown, the device operation continues until the VDD pin voltage
has dropped below the V(OFF) threshold, which must be accounted for while evaluating system shutdown timing
design requirements. Likewise, at system start-up the device does not begin operation until the VDD pin voltage
has exceeded the V(ON) threshold.
The quiescent current consumed by the internal circuit blocks of the device is supplied through the VDD pin.
Although this fact is well known, it is important to recognize that the charge for source current pulses delivered by
the HO pin is also supplied through the same VDD pin. As a result, every time a current is sourced out of the HO
pin, a corresponding current pulse is delivered into the device through the VDD pin. Thus, ensure that a local
bypass capacitor is provided between the VDD and GND pins and located as close to the device as possible for
the purpose of decoupling is important. A low-ESR, ceramic surface-mount capacitor is required. TI recommends
using a capacitor in the range 0.22 µF to 4.7 µF between VDD and GND. In a similar manner, the current pulses
delivered by the HO pin are sourced from the HB pin. Therefore a 0.022-µF to 0.1-µF local decoupling capacitor
is recommended between the HB and HS pins.
20
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
UCC27212
www.ti.com
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
10 Layout
10.1 Layout Guidelines
To
•
•
•
•
•
•
•
•
•
improve the switching characteristics and efficiency of a design, the following layout rules must be followed.
Locate the driver as close as possible to the MOSFETs.
Locate the VDD – VSS and VHB-VHS (bootstrap) capacitors as close as possible to the device (see ).
Pay close attention to the GND trace. Use the thermal pad of the package as GND by connecting it to the
VSS pin (GND). The GND trace from the driver goes directly to the source of the MOSFET, but must not be
in the high current path of the MOSFET drain or source current.
Use similar rules for the HS node as for GND for the high-side driver.
For systems using multiple UCC27212 devices, TI recommends that dedicated decoupling capacitors be
located at VDD–VSS for each device.
Care must be taken to avoid placing VDD traces close to LO, HS, and HO signals.
Use wide traces for LO and HO closely following the associated GND or HS traces. A width of 60 to 100 mils
is preferable where possible.
Use as least two or more vias if the driver outputs or SW node must be routed from one layer to another. For
GND, the number of vias must be a consideration of the thermal pad requirements as well as parasitic
inductance.
Avoid LI and HI (driver input) going close to the HS node or any other high dV/dT traces that can induce
significant noise into the relatively high impedance leads.
A poor layout can cause a significant drop in efficiency or system malfunction, and it can even lead to decreased
reliability of the whole system.
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
21
UCC27212
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
www.ti.com
10.2 Layout Example
HB Bypassing Cap
(Bottom Layer)
Ground plane
(Bottom Layer)
VDD Bypassing Cap
To LO
Load
Ext. Gate
Resistance
(LO)
Ext. Gate
Resistance
(HO)
To HO
Load
Figure 23. UCC27212 Layout Example
10.2.1 Thermal Considerations
The useful range of a driver is greatly affected by the drive-power requirements of the load and the thermal
characteristics of the package. For a gate driver to be useful over a particular temperature range, the package
must allow for efficient removal of the heat produced while keeping the junction temperature within rated limits.
The thermal metrics for the driver package are listed in . For detailed information regarding the table, refer to the
Application Note from Texas Instruments entitled Semiconductor and IC Package Thermal Metrics (SPRA953).
The UCC27212 device is offered in SOIC (8) and VSON (8). The section lists the thermal performance metrics
related to the SOT-23 package.
22
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
UCC27212
www.ti.com
SLUSCO1A – JUNE 2017 – REVISED APRIL 2018
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For related documentation see the following:
• PowerPAD™ Thermally Enhanced Package, Application Report
• PowerPAD™ Made Easy, Application Report
11.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
11.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
Product Folder Links: UCC27212
23
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
UCC27212DPRR
ACTIVE
WSON
DPR
10
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 140
UCC
27212
UCC27212DPRT
ACTIVE
WSON
DPR
10
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 140
UCC
27212
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of