SLUS463C − AUGUST 2000 − REVISED MARCH 2001
D Protects Sensitive Lithium-Ion Cells From
D
D
D
D
D
PACK+
1
TCLK
NC
18
17
16
PACK+
NC
2
15 CBPS
BNEG
3
14 NC
BNEG
4
13 PACK−
BNEG
5
12 PACK−
BNEG
6
11 PACK−
BNEG
7
8
9
PACK−
D
NC
D
D
GSH PACKAGE
(TOP VIEW)
Overcharging and Over-Discharging
Dedicated for One-Cell Applications
Integrated Low-Impedance MOSFET Switch
and Sense Resistor
Precision Trimmed Overcharge and
Overdischarge Voltage Limits
Extremely Low Power Drain
3.5-A Current Capacity
Overcurrent and Short-Circuit Protection
Reverse Charger Protection
Thermal Protection
description
10
PACK−
The UCC3952A is a monolithic BiCMOS lithium−ion battery protection circuit designed to enhance the useful
operating life of a one-cell rechargeable battery pack. Cell protection features include internally trimmed charge
and discharge voltage limits, discharge current limit with a delayed shutdown, and an ultra-low-current sleep
mode state when the cell is discharged. Additional features include an on-chip MOSFET for reduced external
component count and a charge pump for reduced power losses while charging or discharging a low-cell-voltage
battery pack. This protection circuit requires one external capacitor and can operate and safely shut down in
a short circuit condition.
application diagram
TCLK
18
PACK+
17
PACK+
1
+
NC
16
3 kΩ
CBPS
2
NC
3
BNEG
4
BNEG
PACK− 13
5
BNEG
PACK− 12
6
BNEG
PACK− 11
NC
15
14
PACK− 10
BNEG
0.1 µF
CHARGER
LOAD
PACK−
7
9
8
NC
UDG−98205
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2001, Texas Instruments Incorporated
!"#$% ! & '("") % $& ! *(+, '$% ! -$%).
"!-('%& '! !"# %! &*)' '$% ! & *)" %/) %)"#& ! )0$&
&%"(#) %&
&%$ -$"- 1$""$ %2. "!-('% ! *"!')&& 3 -!)& !% )')&&$" ,2 ',(-)
%)&% 3 ! $,, *$"$#)%)"&.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
1
SLUS463C − AUGUST 2000 − REVISED MARCH 2001
AVAILABLE OPTIONS
TA
−20°C to 70°C
PACKAGES
BCC−18 (GSH)
NORMAL TO OVERCHARGE
MIN
OVERVOLTAGE TO NORMAL RECOVERY
TYP
MAX
MIN
TYP
MAX
UNIT
UCC3952AGSH−1
4.15
4.2
4.25
3.85
3.90
3.95
V
UCC3952AGSH−2
4.20
4.25
4.30
3.90
3.95
4.00
V
UCC3952AGSH−3
4.25
4.30
4.35
3.95
4.00
4.05
V
UCC3952AGSH−4
4.30
4.35
4.40
4.00
4.05
4.10
V
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†
Supply voltage (PACK+ to BNEG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Maximum forward voltage (PACK+ to PACK−) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 V
Maximum reverse voltage (where PACK+ to BNEG = 5V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −8 V
Maximum cell continuous charge current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 A
Junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: Currents are positive into, negative out of the specified terminal. Consult Packaging Section of Data Book for thermal limitations and
considerations of packages. All voltages are referenced to GND.
2
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
SLUS463C − AUGUST 2000 − REVISED MARCH 2001
electrical characteristics, TA = −20°C to 70°C, all voltages are with respect to BNEG
(unless otherwise stated)
state transition threshold
PARAMETER
TEST CONDITIONS
UCC3952A−1
UCC3952A−2
VOV
Normal to overcharge voltage
UCC3952A−3
UCC3952A−4
UCC3952A−1
UCC3952A−2
VOVR
Overcharge to normal recovery voltage
UCC3952A−3
UCC3952A−4
VUV
Normal to undercharge
VUVR
Undercharge to normal recovery
tdOD
Overdischarge delay time
tdOV
Overvoltage delay time
MIN
TYP
MAX
4.15
4.20
4.25
TA = 25°C
4.175
4.20
4.235
4.20
4.25
4.30
TA = 25°C
4.225
4.25
4.285
4.25
4.30
4.35
TA = 25°C
4.275
4.30
4.335
4.30
4.35
4.40
4.325
4.35
4.385
3.85
3.90
3.95
3.87
3.90
3.94
3.90
3.95
4.00
3.92
3.95
3.99
3.95
4.00
4.05
3.97
4.00
4.04
4.00
4.05
4.10
4.02
4.05
4.09
2.25
2.35
2.45
2.26
2.35
2.44
2.55
2.65
2.75
2.57
2.65
2.73
10
25
40
TA = 25°C
13.5
25
36
1.0
1.75
2.5
TA = 25°C
1.15
1.75
2.3
MIN
TYP
MAX
3.5
5
6.5
3.8
5
6.3
1
2
3.0
1.05
2
2.9
TA = 25°C
TA = 25°C
TA = 25°C
TA = 25°C
TA = 25°C
TA = 25°C
TA = 25°C
UNITS
V
V
V
V
V
V
V
V
V
V
ms
s
short circuit protection
PARAMETER
TEST CONDITIONS
PACK+ = 3.7 V
ITHLD
Discharge current limit
tdDLY
Discharge current delay
RRESET
Discharge current reset resistance
PACK+ = 3.7 V,
PACK+ = 3.7 V,
TA = 25°C
II = 6.5 A
PACK+ = 3.7 V,
II = 6.5 A, TA = 25°C
PACK+ = 3.7 V
PACK+ = 3.7 V,
•
A
ms
7.5
TA = 25°C
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
UNITS
7.4
MΩ
3
SLUS463C − AUGUST 2000 − REVISED MARCH 2001
electrical characteristics, TA = −20°C to 70°C, all voltages are with respect to BNEG (unless
otherwise stated) (continued)
bias
PARAMETER
TEST CONDITIONS
IDD
Supply current
IDDov
Operating supply current in overvoltage
ISD
Shutdown current
Vmin
Minimum cell voltage when all circuits are fully
functional
MIN
VUV < VPACK < VOV
VUV < VPACK < VOV, TA = 25°C
VOV < VPACK
V(OV) < V(PACK),
V(PACK) = 2.0 V
TA = 25°C
V(PACK) = 2.0 V,
TA = 25°C
TYP
MAX
5
8
5
7.5
11
24
11
22
2.5
2.25
1.7
UNITS
A
µA
µA
A
µA
A
V
FET switch
PARAMETER
VPACK−
Voltage at PACK−
TYP
MAX
UNITS
VPACK > VOV,
1 mA < ISWITCH < 2 A,
Battery overcharged state switch permits discharge
current only.
TEST CONDITIONS
100
400
mV
VPACK > VOV,
1 mA < ISWITCH < 2 A,
Battery overcharged state switch permits discharge
current only,
TA = 25°C
100
350
mV
PACK+ = 2.5V,
−2 mA < ISWITCH < −1 A,
Battery overdischarged state switch permits charge
current only.
PACK+ = 2.5V,
−2 mA < ISWITCH < −1 A,
Battery overdischarged state switch permits charge
current only,
TA = 25°C
PACK+ = 2.5 V,
In normal mode (when not in OV or UV). This value
includes package and bondwire resistance.
RON
Series resistance of the device
MIN
−600
−100
mV
−540
−100
mV
PACK+ = 2.5 V,
TA = 25°C
In normal mode (when not in OV or UV). This value
includes package and bondwire resistance.
60
80
mΩ
60
70
mΩ
thermal shutdown
PARAMETER
T(SD)
TEST CONDITIONS
Thermal shutdown temperature (see Note 2)
TYP
135
NOTE 2: This parameter is ensured by design and is not production tested.
4
MIN
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
MAX
UNITS
°C
SLUS463C − AUGUST 2000 − REVISED MARCH 2001
APPLICATION INFORMATION
PACK+
17
PACK+
16
10 kΩ
VUV
CBPS 15
VUVR
TCLK 18
NC
1
NC
2
VOVR
4−1
MUX
OV
THRESHOLD
COMPARATOR
VOV
SEL
STATE
MACHINE
LOGIC
1.5 V
UV
CLK
BNEG
3
BNEG
4
BNEG
5
6
BNEG
7
NC
8
PACK−
9
TDEL
10 mS
SYSTEM
CLOCK
GENERATOR
TDLS
1 mS
VPUMP
BNEG
TDEL
1 SEC
SETD
50 mV
2 MΩ
50 mV
RST
THERMAL
SHUTDOWN
PACK− 10
PACK− 11
PACK− 12
NC 14
PACK− 13
UDG−98205
Figure 1. Detailed Block Diagram
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
5
SLUS463C − AUGUST 2000 − REVISED MARCH 2001
pin descriptions
BNEG
Connect the negative terminal of the battery to this pin.
PACK+
Connect to the positive terminal of the battery. This pin is available to the user.
CBPS
This power supply bypass pin is connected to PACK+ through an internal 3-kΩ resistor. An external 0.1-µF
capacitor must be connected between this pin and BNEG.
PACK–
The negative terminal of the battery pack (negative terminal available to the user). The internal FET switch
connects this terminal to the BNEG terminal to give the battery pack user appropriate access to the battery. In
an overcharged state, only discharge current is permitted. In an overdischarged state, only charge current is
permitted.
TCLK
Production test mode pin. This pin is used to provide a high-frequency clock to the IC during production testing.
In an application, this pin is left unconnected or tied to BNEG.
6
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
SLUS463C − AUGUST 2000 − REVISED MARCH 2001
APPLICATION INFORMATION
battery voltage monitoring
The battery cell voltage is sampled by connecting a resistor divider across it and comparing the resulting voltage
to a precision internal reference voltage. Under normal conditions (cell voltage is below the overvoltage
threshold and above the undervoltage threshold), the UCC3952A consumes less than 8 µA of current and the
internal MOSFET is fully turned on with the aid of a charge pump.
When the cell voltage falls below the undervoltage threshold for two consecutive samples, the IC disconnects
the load from the battery pack and enters a super-low-power mode. The pack remains in this state until it detects
the application of a charger, at which point charging is enabled. The requirement of two consecutive readings
below the undervoltage threshold filters out momentary drops in cell voltage due to load transients, preventing
nuisance trips.
If the cell voltage exceeds the overvoltage threshold for the overcharge delay time, charging is disabled;
however, discharge current is still allowed. This feature of the IC is explained further in the controlled
charge/discharge mode section of this document.
overcurrent monitoring and protection
Discharge current is continuously monitored via an internal sense resistor. In the event of excessive current,
an overcurrent condition is declared if the high current persists for tdDLY. This delay allows for charging of the
system bypass capacitors without tripping the overcurrent protection. A 0.1-µF capacitor on the CBPS pin
provides momentary holdup for the IC to assure proper operation in the event that a hard short suddenly pulls
the cell voltage below the minimum operating voltage.
Once the overcurrent condition has been declared, the internal MOSFET turns off. To return the device to normal
operation, the UCC3952A needs to have a load impedance greater than 7.5 MΩ placed across PACK+ to
PACK−. This typically can be achieved by removing the battery pack from the system. At this point, the pack
returns to its normal state of operation.
controlled charge/discharge mode
When the chip senses an overvoltage condition, it prevents any additional charging, but allows discharge. This
is accomplished by activating a linear control loop, which controls the gate of the MOSFET based on the
differential voltage across its drain-to-source terminals. The linear loop attempts to regulate the differential
voltage across the MOSFET to 100 mV. When a light load is applied to the part, the loop adjusts the impedance
of the MOSFET to maintain 100 mV across it. As the load increases, the impedance of the MOSFET is
decreased to maintain the 100-mV control. At heavy loads (still below the overcurrent limit), the loop does not
maintain regulation and drives the gate of the MOSFET to the battery voltage (not the charge-pump output
voltage). The MOSFET RDS(on) in the overvoltage state is higher than RDS(on) during normal operation. The
voltage drop (and associated power loss) across the internal MOSFET in this mode of operation is still
significantly lower than the typical solution of two external back-to-back MOSFETs, where the body diode is
conducting.
When the chip senses an undervoltage condition, it disconnects the load from the battery pack and shuts itself
down to minimize current drain from the battery. Several circuits remain powered and detect placement of the
battery pack into a charger. Once the charger presence is detected, the linear loop is activated and the chip
allows charging current into the battery. This linear control mode of operation is in effect until the battery voltage
reaches a level of VUVR , at which time normal operation is resumed.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
7
SLUS463C − AUGUST 2000 − REVISED MARCH 2001
GSH (R-PLGA-N18)
PLASTIC LAND GRID ARRAY
0,60
0,40
3,50
3,30
2,70 TYP
0,50
0,30
0,65
1,30
4,65
4,45
4,05 TYP
3,90 TYP
0,50
0,30
2,90 TYP
0,40
0,20
0,80 MAX
Seating Plane
0,10 MAX
0,05
4200956/A 07/00
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
8
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
