AE15B-UW-S15

Additional Resources: Product Page | PCB Footprint date 02/09/2023 page 1 of 7 SERIES: AE15B-UW │ DESCRIPTION: DC-DC CONVERTER FEATURES • • • • • • • • • up to 15 W isolated output ultra-wide 7.5:1 input voltage range, 200~1,500 V 5,600 Vdc isolation input reverse polarity and under voltage protection output over-voltage, over current, and short circuit protection reinforced insulation PCB, chassis and DIN-rail mounting styles available EN 62109 certified meets UL 1714, CSA C22.2 No. 107.1 MODEL input voltage output voltage output current output power ripple & noise1 efficiency2 range (Vdc) nom (Vdc) max (A) max (W) max (mVp-p) typ (%) AE15B-UW-S5 200~1500 5 2.0 10 150 64 AE15B-UW-S12 200~1500 12 1.25 15 150 71 AE15B-UW-S15 200~1500 15 1.0 15 150 80 AE15B-UW-S24 200~1500 24 0.625 15 150 83 Notes: 1. Measured at nominal input, 20 MHz bandwidth oscilloscope, with 10 µF electrolytic and 1 µF ceramic capacitors on the output. 2. Measured at 800 Vdc input voltage, full load. 3. All specifications are measured at Ta=25°C, humidity < 75%, nominal input voltage, and rated output load unless otherwise specified. PART NUMBER KEY AE15B-UW - SXX - XXX Base Number Output Voltage cui.com Mounting Style: “blank” = board mount T = chassis mount DIN = DIN-rail mount Additional Resources: Product Page | PCB Footprint CUI Inc │ SERIES: AE15B-UW │ DESCRIPTION: DC-DC CONVERTER date 02/09/2023 │ page 2 of 7 INPUT parameter conditions/description operating input voltage transient (10s) under voltage shutdown shut-down range turn-on range current at 200 Vdc at 800 Vdc at 1,500 Vdc inrush current at 200 Vdc at 1,500 Vdc reverse input voltage protection yes input fuse 4 A / 1,500 Vdc (external), required min typ max units 200 800 1,500 1,600 Vdc Vdc 175 200 Vdc Vdc 120 30 16 mA mA mA 130 155 30 90 A A OUTPUT parameter conditions/description maximum capacitive load 5 Vdc output model 12 Vdc output model 15 Vdc output model 24 Vdc output model min total accuracy typ max units 6,000 2,000 1,200 470 μF μF μF μF ±2 % line regulation full load ±1 % load regulation from 0% to full load ±1 % start-up time 200 ~ 1,500 Vdc hold-up time at full load, 25°C, 800 Vdc input 4 2 20 switching frequency 65 temperature coefficient Note: ±0.02 s ms kHz ±0.15 %/°C max units 8 20 30 Vdc Vdc Vdc 4. Tested at full voltage input range, full output load range. (The cooling time between input power-off and power-on again is greater than 15s.) PROTECTIONS parameter conditions/description over voltage protection 5 Vdc output model 12 & 15 Vdc outuput models 24 Vdc ouput model over current protection auto recovery short circuit protection continuous, auto recovery min typ 120 % SAFETY AND COMPLIANCE parameter conditions/description min isolation voltage input to output for 1 minute, 3 mA max safety approvals certified to 62109-1: EN, BS EN conducted emissions CISPR32/EN55032 Class A (see Fig. 2 for recommended circuit) radiated emissions CISPR32/EN55032 Class A (see Fig. 2 for recommended circuit) ESD IEC/EN61000-4-2 Contact +/-6KV/ Air +/-8KV, perf. Criteria B radiated immunity IEC/EN61000-4-3 10V/m, perf. Criteria B EFT/burst IEC/EN61000-4-4 +/- 2KV, +/-4KV (see Fig. 2 for recommended circuit), perf. Criteria B surge IEC/EN61000-4-5 line to line +/-1KV, IEC/EN61000-4-5 line to line +/-2KV (see Fig. 2 for recommended circuit), perf. Criteria B conducted immunity IEC/EN 61000-4-6 10Vr.m.s, perf. Criteria A MTBF as per MIL-HDBK-217F, 25°C max RoHS yes 5,600 300,000 cui.com typ units Vdc hours Additional Resources: Product Page | PCB Footprint CUI Inc │ SERIES: AE15B-UW │ DESCRIPTION: DC-DC CONVERTER date 02/09/2023 │ page 3 of 7 ENVIRONMENTAL parameter conditions/description min max units operating temperature see derating curves -40 70 °C -40 85 °C 95 % 5,000 m storage temperature storage humidity non-condensing altitude see derating curves typ SOLDERABILITY parameter conditions/description min typ max units hand soldering for 3~5 seconds 350 360 370 °C wave soldering for 5~10 seconds 255 260 265 °C parameter conditions/description min typ max units dimensions board mount: 89.00 x 63.50 x 25.00 [3.503 x 2.500 x 0.984 inch] chassis mount: 135.00 x 70.00 x 33.50 [5.314 x 2.755 x 1.319 inch] din-rail mount: 135.00 x 70.00 x 39.00 [5.314 x 2.755 x 1.535 inch] case material black flame-retardant heat-resistant plastic (UL94V-0) weight board mount chassis mount din-rail mount cooling natural convection MECHANICAL 200 280 350 MECHANICAL DRAWING Board mount units: mm [inch] tolerance: ±0.50[±0.020] pin diameter tolerance: ±0.10[±0.004] PIN CONNECTIONS PIN Function 1 -Vin 2 +Vin 3 NC 4 -Vout 5 +Vout mm mm mm NC=no connection cui.com g g g Additional Resources: Product Page CUI Inc │ SERIES: AE15B-UW │ DESCRIPTION: DC-DC CONVERTER Chassis mount units: mm [inch] wire range: 24-12 AWG general tolerance: ±1.00[±0.040] tightening torque: Max 0.4 N∙m PIN CONNECTIONS Function 1 -Vin 2 NC 3 NC 4 NC 5 +Vin 6 NC 7 -Vout 8 +Vout NC=no connection Din-rail mount units: mm [inch] wire range: 24-12 AWG tightening torque: Max 0.4 N∙m mounting rail: TS35, rail needs to connect safety ground tolerance: ±1.00[±0.040] PIN CONNECTIONS PIN Function 1 -Vin 2 NC 3 NC 4 NC 5 +Vin 6 NC 7 -Vout 8 +Vout PCB Footprint date 02/09/2023 │ page 4 of 7 MECHANICAL DRAWING (CONTINUED) PIN | NC=no connection cui.com Additional Resources: Product Page CUI Inc │ SERIES: AE15B-UW │ DESCRIPTION: DC-DC CONVERTER | PCB Footprint date 02/09/2023 │ page 5 of 7 DERATING CURVES Note: 5. For operation of this converter series in an altitude between 2000 - 5000m above sea level, the output power must be derated as per the altitude derating curve. 6. This product is suitable for applications using natural air cooling; for applications in closed environment please contact CUI. EFFICIENCY CURVES cui.com Additional Resources: Product Page | PCB Footprint CUI Inc │ SERIES: AE15B-UW │ DESCRIPTION: DC-DC CONVERTER date 02/09/2023 │ page 6 of 7 APPLICATION CIRCUIT Figure 1 Table 1 Vout (Vdc) C2 (μF/V) TVS 5 120 μF/35V SMBJ7.0A 12 120 μF/35V SMBJ20A 120 μF/35V SMBJ20A 68 μF/35V SMBJ30A 15 Fuse 4 A / 1500 Vdc, required 24 C1 (μF/V) 1 μF/35V We recommend using an electrolytic capacitor with high frequency and low ESR rating for C2 (refer to manufacture’s datasheet). Choose a capacitor voltage rating with at least 20% margin, in other words not exceeding 80%. C1 is a ceramic capacitor, used to filter high-frequency noise. TVS is a recommended suppressor diode to protect the application in case of a converter failure. EMC RECOMMENDED CIRCUIT Figure 2 Table 2 Recommended External Circuit Components C7, C8, C9, C10 safety capacitor 104K/275 Vac C3, C4, C5, C6 10 µF/450 Vdc R1, R2, R3, R4 1 MΩ/2 W LDM 330 µH/1 A LCM 7 mH/1 A FUSE 4 A/1500 Vdc, required Note: See also Table 1. cui.com Additional Resources: Product Page | PCB Footprint CUI Inc │ SERIES: AE15B-UW │ DESCRIPTION: DC-DC CONVERTER date 02/09/2023 │ page 7 of 7 REVISION HISTORY rev. description date 1.0 initial release 11/22/2022 1.01 features updated 12/14/2022 1.02 product image updated 02/09/2023 The revision history provided is for informational purposes only and is believed to be accurate. Headquarters 20050 SW 112th Ave. Tualatin, OR 97062 800.275.4899 Fax 503.612.2383 cui.com techsupport@cui.com CUI offers a two (2) year limited warranty. Complete warranty information is listed on our website. CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use. CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.