CY25100ZXCFT

CY25100 Field and Factory Programmable Spread Spectrum Clock Generator for EMI Reduction Field and Factory Programmable Spread Spectrum Clock Generator for EMI Reduction Features Functional Description ■ Wide Operating Output (SSCLK) Frequency Range ❐ 3 MHz to 200 MHz ■ Programmable Spread Spectrum with nominal 31.5 kHz Modulation Frequency ❐ Center Spread: ±0.25% to ±2.5% ❐ Down Spread: –0.5% to –5.0% ■ Input frequency range ❐ External Crystal: 8 to 30 MHz Fundamental Crystals ❐ External Reference: 8 to 166 MHz Clock ■ Integrated Phase-Locked Loop (PLL) ■ Field Programmable devices available ■ Programmable Crystal Load Capacitor Tuning Array ■ Low Cycle-to-cycle Jitter ■ Spread Spectrum on/off function ■ Powerdown or Output Enable function ■ Commercial and Industrial temperature ranges ■ 3.3 V operation ■ 8-pin TSSOP and SOIC packages The CY25100 is a Spread Spectrum Clock Generator (SSCG) IC used to reduce EMI found in today’s high speed digital electronic systems. The device uses a Cypress proprietary PLL and Spread Spectrum Clock (SSC) technology to synthesize and modulate the frequency of the input clock. By frequency modulating the clock, the measured EMI at the fundamental and harmonic frequencies are greatly reduced. This reduction in radiated energy can significantly reduce the cost of complying with regulatory agency (EMC) requirements and improve time-to-market without degrading system performance. The CY25100 uses a factory or field-programmable configuration memory array to synthesize output frequency, spread percentage, crystal load capacitor, reference clock output on/off, spread spectrum on/off function, and PD#/OE options. The spread percentage is programmed to either center spread or down spread with various spread percentages. The range for center spread is from ±0.25% to ±2.50%. The range for down spread is from –0.5% to –5.0%. The input to the CY25100 can either be a crystal or a clock signal. The CY25100 has two clock outputs: REFCLK and SSCLK. The non-spread spectrum REFCLK output has the same frequency as the input of the CY25100. For a complete list of related documentation, click here. Logic Block Diagram R FB P LL w ith M O D U LA TIO N C O N TR O L 3 XIN C XIN O U TP U T D IVID E R S and MUX PR O G R A M M A B LE C O N FIG U R A TIO N 2 XOUT C XOUT 6 R E FC LK 7 4 SS C LK P D # or O E 8 S SO N # Cypress Semiconductor Corporation Document Number: 38-07499 Rev. *M • 1 5 VD D V SS 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised February 1, 2018 CY25100 Contents Pinouts .............................................................................. 3 Pin Description ................................................................. 3 User Specified Variables .................................................. 3 Programming Description ............................................... 4 Field Programmable CY25100 .................................. 4 CY3672 Programmer and CY3690/CY3691 Socket Adapters .............................. 4 Factory Programmable CY25100 ................................ 4 Product Functions ............................................................ 4 Input Frequency (XIN, Pin 3 and XOUT, Pin 2) ........... 4 CXIN and CXOUT (Pin 3 and Pin 2) ........................... 4 Output Frequency (SSCLK, Pin 7) .............................. 4 Spread Percentage (SSCLK, Pin 7) ............................ 4 Reference Output (REFOUT, Pin 6) ............................ 4 Modulation Frequency ................................................. 4 Power Down or Output Enable (PD# or OE, Pin 4) ..... 4 Absolute Maximum Ratings ............................................ 5 Recommended Crystal Specifications ........................... 5 Operating Conditions ....................................................... 5 DC Electrical Characteristics .......................................... 6 Document Number: 38-07499 Rev. *M Thermal Resistance .......................................................... 6 Application Circuit ............................................................ 7 AC Electrical Characteristics .......................................... 8 Switching Waveforms ...................................................... 9 Informational Graphs ..................................................... 10 Ordering Information ...................................................... 12 Possible Configurations ............................................. 12 Ordering Code Definitions ......................................... 13 Package Diagrams .......................................................... 14 Acronyms ........................................................................ 16 Document Conventions ................................................. 16 Units of Measure ....................................................... 16 Document History Page ................................................. 17 Sales, Solutions, and Legal Information ...................... 19 Worldwide Sales and Design Support ....................... 19 Products .................................................................... 19 PSoC® Solutions ...................................................... 19 Cypress Developer Community ................................. 19 Technical Support ..................................................... 19 Page 2 of 19 CY25100 Pinouts Figure 1. 8-pin SOIC/TSSOP pinout CY25100 1 VDD SSON# 8 2 XOUT SSCLK 7 3 XIN/CLKIN REFCLK 6 4 PD#/OE VSS 5 Pin Description Pin Name Type Description 1 VDD Power 3.3 V power supply. 2 XOUT Output Crystal output. Leave this pin floating if external clock is connected to pin 3. 3 XIN/CLKIN Input Crystal input or reference clock input. 4 PD#/OE Input User has the option of choosing either PD# or OE function. Power Down pin: Active LOW. If PD# = 0, PLL and crystal oscillator circuit are powered down, and outputs are weakly pulled low. Output Enable pin: Active HIGH. If OE = 1, SSCLK and REFCLK are enabled. 5 VSS Power Power supply ground. 6 REFCLK Output Buffered reference output. 7 SSCLK Output Spread spectrum clock output. 8 SSON# Input Spread spectrum control: Active LOW. 0 = spread on. 1 = spread off. User Specified Variables Pin Function Input Frequency Total Crystal Load Capacitance Output Frequency Spread Percent (0.5% – 5%, 0.25% granularity) Reference Output Power Down or Output Enable Pin Name XIN and XOUT XIN and XOUT SSCLK SSCLK REFOUT PD#/OE Pin# 3 and 2 3 and 2 7 7 6 4 Unit MHz pF MHz % and Center- or Down-spread On or Off Select PD# or OE USER SPECIFIED USER SPECIFIED USER SPECIFIED USER SPECIFIED USER SPECIFIED USER SPECIFIED Document Number: 38-07499 Rev. *M Page 3 of 19 CY25100 Programming Description programmable from 12 pF to 60 pF, in 0.5 pF increments.This feature eliminates the need for external crystal load capacitors. Field Programmable CY25100 The following formula is used to calculate the value of CXIN and CXOUT for matching the crystal load (CL): The CY25100 is programmed at the package level, and must be programmed prior to installation on a circuit board. Field programmable devices are denoted by an “F” in the ordering code, and are blank when shipped. The CY25100 is Flash technology based, which allows it to be reprogrammed up to 100 times. This allows fast and easy design changes and product updates, and eliminates issues with old and out of date inventory. Samples and small prototype quantities can be programmed on the CY3672 programmer with the CY3690 (TSSOP package) or CY3691 (SOIC package) socket adapter. CY3672 Programmer and CY3690/CY3691 Socket Adapters The Cypress CY3672 programmer and the CY3690 or CY3691 socket adapter may be used to program field programmable versions of the CY25100. The CY3690 enables users to program the CY25100ZXCF and CY25100ZXIF (TSSOP). CY3691 provides the ability to program the CY25100SXCF and CY25100SXIF (SOIC). The CY3690 and CY3691 are separate orderable items, so the existing users of the CY3672 programmer need to order only the specific socket adapter to program the CY25100. Factory Programmable CY25100 Factory programming by Cypress is available for high volume orders. All requests must be submitted to the local Cypress Field Application Engineer (FAE) or sales representative. After the request is processed, you will receive a new part number, samples, and data sheet with the programmed values. This part number is used for additional sample requests and production orders. Product Functions Input Frequency (XIN, Pin 3 and XOUT, Pin 2) The input to the CY25100 can be a crystal or a clock. The input frequency range for crystals is 8 to 30 MHz, and for clock signals is 8 to 166 MHz. CXIN and CXOUT (Pin 3 and Pin 2) The CY25100 has internal load capacitors at Pin 3 (CXIN) and Pin 2 (CXOUT) CXIN always equals CXOUT, and they are Document Number: 38-07499 Rev. *M CXIN = CXOUT = 2CL – CP where CL is the crystal load capacitor as specified by the crystal manufacturer and CP is the parasitic PCB capacitance on each node of the crystal. For example, if a crystal with CL of 16 pF is used, and CP is 2 pF, CXIN and CXOUT are calculated as: CXIN = CXOUT = (2 × 16) – 2 = 30 pF If using a driven reference, set CXIN and CXOUT to the minimum value 12 pF, connect the reference to XIN/CLKIN, and leave XOUT unconnected. Output Frequency (SSCLK, Pin 7) The modulated frequency at the SSCLK output is produced by synthesizing the input reference clock. The modulation can be stopped by SSON# digital control input (SSON# = HIGH, no modulation). If modulation is stopped, the clock frequency is the nominal value of the synthesized frequency without modulation (spread percentage = 0). The range of synthesized clock is from 3 to 200 MHz. Spread Percentage (SSCLK, Pin 7) The SSCLK spread can be programmed at any percentage value from ±0.25% to ±2.5% for center spread and from –0.5% to –5.0% for down spread. Reference Output (REFOUT, Pin 6) The reference clock output has the same frequency and the same phase as the input clock. This output can be programmed to be enabled (clock on) or disabled (High Z, clock off). If this output is not required, it is recommended that the disabled (High Z, Clock Off) option be selected. Modulation Frequency The modulation frequency is 31.5 kHz for all SSCLK frequencies from 3 to 200 MHz. Power Down or Output Enable (PD# or OE, Pin 4) The part can be programmed to include either PD# or OE function. PD# function powers down the oscillator and PLL. The OE function disables the outputs. Page 4 of 19 CY25100 Junction Temperature .............................. –40 C to +125 C Absolute Maximum Ratings Data Retention at Tj = 125 C ..............................> 10 years Supply Voltage (VDD) ...................................... –0.5 to +7.0 V Package Power Dissipation ..................................... 350 mW DC Input Voltage ................................ –0.5 V to VDD + 0.5 V Static Discharge Voltage (per MIL-STD-883, Method 3015) .......................... > 2000V Storage Temperature (Non condensing) .................................... –55 C to +125 C Recommended Crystal Specifications Parameter Description Comments Min Typ Max Unit fNOM Nominal Crystal Frequency Parallel resonance, fundamental mode, AT cut 8 – 30 MHz CLNOM Nominal Load Capacitance Internal load caps 6 – 30 pF R1 Equivalent Series Resistance (ESR) Fundamental mode – – 25  R3/R1 Ratio of Third Overtone Mode Ratio used because typical R1 ESR to Fundamental Mode ESR values are much less than the maximum spec 3 – – – DL Crystal Drive Level – 0.5 2 mW No external series resistor assumed Operating Conditions Parameter Description VDD Supply Voltage TA Ambient Commercial Temperature Ambient Industrial Temperature Min Typ Max Unit 3.13 3.30 3.45 V 0 – 70 °C –40 – 85 °C CLOAD Maximum Load Capacitance at Pin 6 and Pin 7 – – 15 pF fREF External Reference Crystal (Fundamental tuned crystals only) 8 – 30 MHz External Reference Clock 8 – 166 MHz fSSCLK SSCLK Output Frequency, CLOAD = 15 pF 3 – 200 MHz fREFCLK REFCLK Output Frequency, CLOAD = 15 pF 8 – 166 MHz fMOD Spread Spectrum Modulation Frequency 30.0 31.5 33.0 kHz tPU Power Up Time for all VDD’s to reach minimum specified voltage (power ramp must be monotonic) 0.05 – 500 ms Document Number: 38-07499 Rev. *M Page 5 of 19 CY25100 DC Electrical Characteristics Parameter Description Condition Min Typ Max Unit IOH Output High Current VOH = VDD – 0.5 V, VDD = 3.3 V (source) 10 12 – mA IOL Output Low Current VOL = 0.5 V, VDD = 3.3 V (sink) 10 12 – mA VIH Input High Voltage CMOS levels, 70% of VDD 0.7 × VDD – VDD V VIL Input Low Voltage CMOS levels, 30% of VDD – – 0.3 × VDD V IIH Input High Current, PD#/OE and Vin = VDD SSON# Pins –10 – 10 A IIL Input Low Current, PD#/OE and Vin = VSS SSON# Pins –10 – 10 A IOZ Output Leakage Current Three-state output, PD#/OE = 0, output pulldown resistor disabled –10 – 10 A CXIN or CXOUT[1] Programmable Capacitance at Pin 2 and Pin 3 Capacitance at minimum setting – 12 – pF Capacitance at maximum setting – 60 – pF [1] Input Capacitance at Pin 4 and Pin 8 Input pins excluding XIN and XOUT – 5 7 pF IVDD Supply Current VDD = 3.45 V, Fin = 30 MHz, REFCLK = 30 MHz, SSCLK = 66 MHz, CLOAD = 15 pF, PD#/OE = SSON# = VDD – 25 35 mA IDDS Standby Current VDD = 3.45 V, Device powered down with PD# = 0 V (driven reference pulled down) – 15 30 A CIN Thermal Resistance Parameter [2] Description θJA Thermal resistance (junction to ambient) θJC Thermal resistance (junction to case) Test Conditions 8-pin SOIC 8-pin TSSOP Unit Test conditions follow standard test methods and procedures for measuring thermal impedance, in accordance with EIA/JESD51. 134 161 °C/W 49 31 °C/W Notes 1. Guaranteed by characterization, not 100% tested. 2. These parameters are guaranteed by design and are not tested. Document Number: 38-07499 Rev. *M Page 6 of 19 CY25100 Application Circuit Figure 2. Application Circuit Diagram [3, 4, 5] Power SSON# 8 1 VDD 0.1uF 2 XOUT SSCLK 7 CY25100 3 XIN/CLKIN VDD 4 PD#/OE REFCLK 6 VSS 5 Notes 3. Because the load capacitors (CXIN and CXOUT) are provided by the CY25100, no external capacitors are needed on the XIN and XOUT pins to match the crystal load capacitor (CL). Only a single 0.1-F bypass capacitor is required on the VDD pin. 4. If an external clock is used, apply the clock to XIN (pin 3) and leave XOUT (pin 2) floating (unconnected). 5. If SSON# (pin 8) is LOW (VSS), the frequency modulation is on at SSCLK (pin 7). Document Number: 38-07499 Rev. *M Page 7 of 19 CY25100 AC Electrical Characteristics The AC Electrical Characteristics for part CY25100 is as follows. [6] Parameter DC Description Output Duty Cycle Output Duty Cycle SR1 Rising Edge Slew Rate SR2 Falling Edge Slew Rate SR3 Rising Edge Slew Rate SR4 Falling Edge Slew Rate tCCJ1[7] Cycle-to-Cycle Jitter, SSCLK (Pin 7) tCCJ2[7] tCCJ3[7] Cycle-to-Cycle Jitter, SSCLK (Pin 7) Cycle-to-Cycle Jitter, REFCLK (Pin 6) tSTP Power down Time (pin 4 = PD#) tOE1 Output Disable Time (pin 4 = OE) tOE2 Output Enable Time (pin 4 = OE) tPU1 Power Up Time, Crystal is used tPU2 Power Up Time, Reference clock is used Condition SSCLK, Measured at VDD/2 REFCLK, Measured at VDD/2, Duty Cycle of CLKIN = 50% at input bias SSCLK from 3 to 100 MHz; REFCLK from 3 to 100 MHz; 20%–80% of VDD SSCLK from 3 to 100 MHz; REFCLK from 3 to 100 MHz; 80%–20% of VDD SSCLK from 100 to 200 MHz; REFCLK from 100 to 166 MHz; 20%–80% of VDD SSCLK from 100 to 200 MHz; REFCLK from 100 to 166 MHz; 80%–20% of VDD CLKIN = SSCLK = 166 MHz, 2% spread, REFCLK off CLKIN = SSCLK = 66 MHz, 2% spread, REFCLK off CLKIN = SSCLK = 33 MHz, 2% spread, REFCLK off CLKIN = SSCLK = 166 MHz, 2% spread, REFCLK on CLKIN = SSCLK = 66 MHz, 2% spread, REFCLK on CLKIN = SSCLK = 33 MHz, 2% spread, REFCLK on CLKIN = SSCLK = 166 MHz, 2% spread, REFCLK on CLKIN = SSCLK = 66 MHz, 2% spread, REFCLK on CLKIN = SSCLK = 33 MHz, 2% spread, REFCLK on Time from falling edge on PD# to stopped outputs (Asynchronous) Time from falling edge on OE to stopped outputs (Asynchronous) Time from rising edge on OE to outputs at a valid frequency (Asynchronous) Time from rising edge on PD# to outputs at valid frequency (Asynchronous) Time from rising edge on PD# to outputs at valid frequency (Asynchronous), reference clock at correct frequency Min 45 40 Typ 50 50 Max 55 60 Unit % % 0.7 1.1 3.6 V/ns 0.7 1.1 3.6 V/ns 1.0 1.6 4.0 V/ns 1.2 1.6 4.0 V/ns – 90 120 ps – 100 130 ps – 130 170 ps – 100 130 ps – 105 140 ps – 200 260 ps – 80 100 ps – 100 130 ps – 135 180 ps – 150 350 ns – 150 350 ns – 150 350 ns – 3.5 5 ms – 2 3 ms Notes 6. Guaranteed by characterization, not 100% tested. 7. Jitter is configuration dependent. Actual jitter is dependent on XIN jitter and edge rate, number of active outputs, output frequencies, spread percentage, temperature, and output load. Document Number: 38-07499 Rev. *M Page 8 of 19 CY25100 Switching Waveforms Figure 3. Duty Cycle Timing (DC = t1A/t1B) OUTPUT t1A t1B Figure 4. Output Rise/Fall Time (SSCLK and REFCLK) VDD OUTPUT 0V Tr Tf Output Rise time (Tr) = (0.6 x VDD)/SR1 (or SR3) Output Fall time (Tf) = (0.6 x VDD)/SR2 (or SR4) Refer to AC Electrical Characteristics table for SR (Slew Rate) values. Figure 5. Power Down and Power Up Timing VDD POWER DOWN 0V VIH VIL tPU High Impedance CLKOUT (Asynchronous) tSTP Figure 6. Output Enable/Disable Timing VDD OUTPUT ENABLE 0V VIH VIL TOE2 High Impedance CLKOUT (Asynchronous) TOE1 Document Number: 38-07499 Rev. *M Page 9 of 19 CY25100 Informational Graphs The Informational Graphs are as follows. [8] 161.5 169.5 169 168.5 168 167.5 167 166.5 166 165.5 165 164.5 164 163.5 163 160.5 162.5 172.5 171.5 Spread Spectrum Profile: Fnom=166MHz, Fmod=30kHz, Spread%= -4% 170.5 169.5 168.5 167.5 166.5 Fnominal 165.5 164.5 163.5 162.5 Spread Spectrum Profile: Fnom=166MHz, Fmod=30kHz, Spread%= +/-1% Fnominal 159.5 0 20 68.5 40 60 80 100 120 Time (us) 140 160 180 0 200 Spread Spectrum Profile: Fnom=66MHz, Fmod=30kHz, Spread%= -4% 68 20 67.5 67.5 67 67 66.5 66.5 Fnominal 66 40 60 80 100 120 Time (us) 140 160 180 200 Spread Spectrum Profile: Fnom=66MHz, Fmod=30kHz, Spread%= +/-1% Fnominal 66 65.5 65.5 65 64.5 65 64 64.5 63.5 0 20 40 60 80 100 120 Time (us) 140 160 180 0 200 20 40 60 80 100 120 Time (us) 140 160 180 200 IDD vs. SSCLK Duty Cycle vs. REFCLK T e m p e r atu r e =25C, V DD=3.3V , CL OAD=15p F, SS o ff, ( C L OA D =1 5 p F ) 60 58 56 54 52 50 48 46 44 42 40 30 25 IDD (m A) Duty Cycle (%) Re fclk = 30M Hz 20 15 10 5 0 50 100 REFCLK (MHz) 150 200 0 0 50 100 150 200 SSCL K (M Hz ) Note 8. The Informational Graphs are meant to convey the typical performance levels. No performance specifications is implied or guaranteed. Refer to DC Electrical Characteristics on page 6 and AC Electrical Characteristics on page 8 for device specifications. Document Number: 38-07499 Rev. *M Page 10 of 19 CY25100 Informational Graphs (continued) The Informational Graphs are as follows. [8] Measured Spread% vs. VDD over Tem perature (Target Spread = 0.5%, Fout=100MHz, CLOA D =15pF) Measured Spread% vs. VDD over Tem perature (Target Spread = 5.0%, Fout=100MHz, CLOA D =15pF) 0.55% -40C 0.50% 25C 0.45% 85C 6.00% Spread% Spread% 0.60% 5.50% -40C 5.00% 25C 4.50% 85C 4.00% 0.40% 2.7 3 3.3 3.6 2.7 3.9 3 3.3 SSCLK Attenuation vs. VDD over Tem perature (Measured at 7th Harmonic w ith Fnom=100MHz and Spread=5.0%, CLOAD=15pF) 0 -2 -40C -4 25C -6 85C -8 -10 3.3 3.6 Attenuation (dB) Attenuation (dB) SSCLK Attenuation vs. VDD over Tem perature (Measured at 7th Harmonic w ith Fnom=100MHz and Spread=0.5%, CLOA D =15pF) 3 -10 -12 -14 -16 -18 -20 -40C 25C 85C 2.7 3.9 3 3.3 3.9 Max Cycle-Cycle Jitter on SSCLK vs. Tem perature (SSCLK=100MHz, VDD=3.3V, CLOAD=15pF, +/2%spread, REFCLK off) SSCLK EMI Attenuation vs. Spread% (Measured at 7th Harmonic Temp=25C, VDD=3.3V, SSCLK=100MHz, Measured on Cypress Characterization board w ith CLOAD=15pF) 0 200 -2 175 -4 150 Jitter (ps) Attenuation (dB) 3.6 VDD (V) VDD (V) -6 -8 - 10 - 12 125 100 75 50 25 - 14 0 - 16 0.0% 3.9 VDD (V) VDD (V) 2.7 3.6 0.5% 1.0% 1.5% 2.0% 2.5% 3.0% Spread % Document Number: 38-07499 Rev. *M 3.5% 4.0% 4.5% 5.0% - 40 - 20 0 20 40 60 80 100 Tem perature (deg C) Page 11 of 19 CY25100 Ordering Information Ordering Code Package Description Product Flow Pb-free CY25100SXCF 8-pin SOIC Commercial, 0 °C to 70 °C CY25100SXCFT 8-pin SOIC – Tape and Reel Commercial, 0 °C to 70 °C CY25100SXIF 8-pin SOIC Industrial, –40 °C to 85 °C CY25100SXIFT 8-pin SOIC – Tape and Reel Industrial, –40 °C to 85 °C CY25100ZXCF 8-pin TSSOP Commercial, 0 °C to 70 °C CY25100ZXCFT 8-pin TSSOP – Tape and Reel Commercial, 0 °C to 70 °C CY25100ZXIF 8-pin TSSOP Industrial, –40 °C to 85 °C CY25100ZXIFT 8-pin TSSOP – Tape and Reel Industrial, –40 °C to 85 °C Programmer CY3675-CLKMAKER1 Programmer Some product offerings are factory programmed customer specific devices with customized part numbers. The Possible Configurations table shows the available device types, but not complete part numbers. Contact your local Cypress FAE or Sales Representative for more information. Possible Configurations Ordering Code Package Description Product Flow CY25100ZIxxx[9, 10] 8-pin TSSOP Industrial, –40 °C to 85 °C CY25100ZIxxxT[9, 10] 8-pin TSSOP – Tape and Reel Industrial, –40 °C to 85 °C CY25100SXCxxx[9] 8-pin SOIC Commercial, 0 °C to 70 °C CY25100SXCxxxT[9] 8-pin SOIC – Tape and Reel Commercial, 0 °C to 70 °C CY25100SXIxxx[9] 8-pin SOIC Industrial, –40 °C to 85 °C CY25100SXIxxxT[9] 8-pin SOIC – Tape and Reel Industrial, –40 °C to 85 °C CY25100ZXCxx[9] 8-pin TSSOP Commercial, 0 °C to 70 °C CY25100ZXCxxT[9] 8-pin TSSOP – Tape and Reel Commercial, 0 °C to 70 °C CY25100ZXIxx[9] 8-pin TSSOP Industrial, –40 °C to 85 °C CY25100ZXIxxT[9] 8-pin TSSOP – Tape and Reel Industrial, –40 °C to 85 °C Pb-free Note 9. Ordering codes with “xxx” or “xx” are factory-programmed configurations. “xxx” or “xx” denotes the specific device configuration. “w” denotes the revision. Factory programming is available for high-volume orders. For more details, contact your local Cypress field application engineer or Cypress Sales Representative. 10. Not recommended for new designs. New designs should use Pb-free devices. Document Number: 38-07499 Rev. *M Page 12 of 19 CY25100 Ordering Code Definitions CY 25100 X X X F (xx, xxx) T T = Tape and Reel; blank = Tube Custom configuration code (Factory Programmed Device only) Programming: F = Field Programmable; blank = Factory Programmed Temperature Range: X = C or I C = Commercial; I = Industrial X = Pb-free package Package Type: X = S or Z S = 8-pin SOIC; Z = 8-pin TSSOP Base Part Number Company ID: CY = Cypress Document Number: 38-07499 Rev. *M Page 13 of 19 CY25100 Package Diagrams Figure 7. 8-pin SOIC (150 Mils) S08.15/SZ08.15/SW815 Package Outline, 51-85066 51-85066 *I Document Number: 38-07499 Rev. *M Page 14 of 19 CY25100 Package Diagrams (continued) Figure 7. 8-pin TSSOP (4.40 mm Body) Z08.173/ZZ08.173 Package Outline, 51-85093 51-85093 *E Document Number: 38-07499 Rev. *M Page 15 of 19 CY25100 Acronyms Acronym Document Conventions Description Units of Measure DC Direct Current EMI Electromagnetic Interference °C degree Celsius ESR Equivalent Series Resistance kHz kilohertz FAE Field Application Engineer MHz megahertz JEDEC Joint Electron Devices Engineering Council µA microampere OE Output Enable µF microfarad PCB Printed Circuit Board mA milliampere PD Power Down mm millimeter PLL Phase Locked Loop ms millisecond SOIC Small Outline Integrated Circuit mW milliwatt SSC Spread Spectrum Clock ns nanosecond SSCG Spread Spectrum Clock Generator  ohm TSSOP Thin Shrunk Small Outline Package % percent Document Number: 38-07499 Rev. *M Symbol Unit of Measure pF picofarad ps picosecond V volt Page 16 of 19 CY25100 Document History Page Document Title: CY25100, Field and Factory Programmable Spread Spectrum Clock Generator for EMI Reduction Document Number: 38-07499 Rev. ECN No. Orig. of Change Submission Date ** 126578 CKN 06/27/2003 New data sheet. *A 128753 IJATMP 08/29/2003 Updated Programming Description: Added Field Programmable CY25100. Added CyberClocks™ Online Software. Added CY3672 Programmer and CY3690/CY3691 Socket Adapters. Added Factory Programmable CY25100. Removed “Custom Configuration Request Procedure”. Updated Ordering Information: Updated part numbers. Added Note 9 and referred the same note in “Part Number” column. *B 130342 RGL 12/02/2003 Updated Application Circuit: Updated Figure 2. Updated Ordering Information: No change in part numbers. Updated details in “Package Description” column corresponding to MPNs CY3690 and CY3691. Updated Package Diagrams: spec 51-85066 – Changed revision from *B to *C. spec 51-85093 – Changed revision from ** to *A. *C 204121 RGL 02/11/2004 Added Industrial Temperature Range related information in all instances across the document. Updated Ordering Information: Updated part numbers. Updated Note 9. *D 215392 RGL 03/31/2004 Updated Ordering Information: Updated part numbers. *E 2513909 AESA 06/10/2008 Updated Ordering Information: Updated part numbers. Replaced “Lead free” with “Pb-Free”. Added Note 10 and referred the same note in corresponding MPNs. Added “Pb-Free” in header. Updated details in “Package Description” column (Removed Pb-Free). Updated to new template. *F 2601881 KVM / PYRS 11/06/2008 Updated AC Electrical Characteristics: Changed minimum value of SR3 parameter from 1.2 V/ns to 1.0 V/ns. Updated Ordering Information: Updated part numbers. Removed reference of Note 9 from Parameter column. Referred Note 9 in ‘xxx’ parts. *G 2742910 KVM 07/23/2009 General text cleanup across the document. Replaced “CY3672 FTG” with “CY3672” in all instances across the document. Removed “Benefits”. Updated Pin Description: Added a column “Type” and added corresponding details of all pins. Updated Programming Description: Updated CyberClocks™ Online Software: Updated description. Updated Product Functions: Updated Modulation Frequency: Updated description. Document Number: 38-07499 Rev. *M Description of Change Page 17 of 19 CY25100 Document History Page (continued) Document Title: CY25100, Field and Factory Programmable Spread Spectrum Clock Generator for EMI Reduction Document Number: 38-07499 Rev. ECN No. Orig. of Change Submission Date Description of Change *G (cont.) 2742910 KVM 07/23/2009 Updated DC Electrical Characteristics: Added minimum values for IIH and IIL parameters. Updated details in “Condition” column corresponding to IOZ parameter. Updated AC Electrical Characteristics: Standardized timing parameter names to upper case in “Parameter” column. Updated Ordering Information: Updated part numbers. Updated Note 9. Updated Note 10. *H 2897317 KVM 03/22/2010 Updated Ordering Information: Updated part numbers. Added Possible Configurations: Moved ‘xxx’ parts under Possible Configurations. Updated Package Diagrams: spec 51-85066 – Changed revision from *C to *D. spec 51-85093 – Changed revision from *A to *B. *I 3366141 PURU 09/12/2011 Updated Logic Block Diagram. Updated Ordering Information: No change in part numbers. Added Ordering Code Definitions. Updated Package Diagrams: spec 51-85066 – Changed revision from *D to *E. spec 51-85093 – Changed revision from *B to *C. Added Acronyms and Units of Measure. Updated to new template. Completing Sunset Review. *J 4108421 CINM 08/30/2013 Updated Package Diagrams: spec 51-85066 – Changed revision from *E to *F. spec 51-85093 – Changed revision from *C to *D. Updated to new template. Completing Sunset Review. *K 4581659 TAVA 11/28/2014 Updated Functional Description: Added “For a complete list of related documentation, click here.” at the end. Updated Package Diagrams: spec 51-85093 – Changed revision from *D to *E. *L 5516747 PSR / PAWK 11/10/2016 Updated Programming Description: Removed “CyberClocks Online Software”. Added Thermal Resistance. Updated Package Diagrams: spec 51-85066 – Changed revision from *F to *H. Updated to new template. Completing Sunset Review. *M 6015682 PAWK 02/01/2018 Updated Ordering Information: Updated part numbers. Updated Package Diagrams: spec 51-85066 – Changed revision from *H to *I. Updated to new template. Document Number: 38-07499 Rev. *M Page 18 of 19 CY25100 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC® Solutions Products Arm® Cortex® Microcontrollers Automotive cypress.com/arm cypress.com/automotive Clocks & Buffers Interface Internet of Things Memory cypress.com/clocks cypress.com/interface cypress.com/iot cypress.com/memory Microcontrollers cypress.com/mcu PSoC cypress.com/psoc Power Management ICs Touch Sensing USB Controllers Wireless Connectivity PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6 MCU Cypress Developer Community Community | Projects | Video | Blogs | Training | Components Technical Support cypress.com/support cypress.com/pmic cypress.com/touch cypress.com/usb cypress.com/wireless © Cypress Semiconductor Corporation, 2003-2018. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document, including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited. TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products. Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners. Document Number: 38-07499 Rev. *M Revised February 1, 2018 Page 19 of 19