CY62137VN MoBL®
2-Mbit (128K x 16) Static RAM
Features
• Temperature Ranges
— Industrial: –40°C to 85°C
— Automotive-A: –40°C to 85°C
— Automotive-E: –40°C to 125°C
• High Speed: 55 ns
• Wide voltage range: 2.7V–3.6V
• Ultra-low active, standby power
• Easy memory expansion with CE and OE features
• TTL-compatible inputs and outputs
• Automatic power-down when deselected
• CMOS for optimum speed/power
• Available in Pb-free 44-pin TSOP Type II package
Functional Description[1]
The CY62137VN is a high-performance CMOS static RAM
organized as 128K words by 16 bits. This device features
advanced circuit design to provide ultra-low active current.
This is ideal for providing More Battery Life™ (MoBL®) in
portable applications such as cellular telephones. The device
also has an automatic power-down feature that reduces power
consumption by 99% when addresses are not toggling. The
device can also be put into standby mode when deselected
(CE HIGH) or when CE is LOW and both BLE and BHE are
HIGH. The input/output pins (I/O0 through I/O15) are placed in
a high-impedance state when: deselected (CE HIGH), outputs
are disabled (OE HIGH), BHE and BLE are disabled (BHE,
BLE HIGH), or during a write operation (CE LOW, and WE
LOW).Writing to the device is accomplished by taking Chip
Enable (CE) and Write Enable (WE) inputs LOW. If Byte Low
Enable (BLE) is LOW, then data from I/O pins (I/O0 through
I/O7), is written into the location specified on the address pins
(A0 through A16). If Byte High Enable (BHE) is LOW, then data
from I/O pins (I/O8 through I/O15) is written into the location
specified on the address pins (A0 through A16).Reading from
the device is accomplished by taking Chip Enable (CE) and
Output Enable (OE) LOW while forcing the Write Enable (WE)
HIGH. If Byte Low Enable (BLE) is LOW, then data from the
memory location specified by the address pins will appear on
I/O0 to I/O7. If Byte High Enable (BHE) is LOW, then data from
memory will appear on I/O8 to I/O15. See the truth table at the
back of this data sheet for a complete description of read and
write modes.
Logic Block Diagram
DATA IN DRIVERS
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
SENSE AMPS
ROW DECODER
10
128K x 16
RAM Array
I/O0–I/O7
I/O8–I/O15
BHE
WE
CE
OE
BLE
A12
A13
A14
A15
A16
A11
COLUMN DECODER
CE
Power-down
Circuit
BHE
BLE
Note:
1. For best practice recommendations, please refer to the Cypress application note “System Design Guidelines” on http://www.cypress.com.
Cypress Semiconductor Corporation
Document #: 001-06497 Rev. *A
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised August 3, 2006
[+] Feedback
CY62137VN MoBL®
Product Portfolio
Power Dissipation
Speed
(ns)
VCC Range (V)
Product
CY62137VNLL Industrial
Min.
Typ.[3]
Max.
2.7
3.0
3.6
55
Operating, ICC
(mA)
Standby, ISB2
(µA)
Typ.[3]
Max.
Typ.[3]
Max.
7
20
1
15
CY62137VNLL
70
7
15
1
15
CY62137VNLL Automotive-A
70
7
15
1
15
CY62137VNLL Automotive-E
70
7
15
1
20
Pin Configurations
TSOP II (Forward)
Top View
A4
A3
A2
A1
A0
CE
I/O0
I/O1
I/O2
I/O3
VCC
VSS
I/O4
I/O5
I/O6
I/O7
WE
A16
A15
A14
A13
A12
1
44
2
3
43
42
4
41
40
39
38
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
A5
A6
A7
OE
BHE
BLE
I/O15
I/O14
I/O13
I/O12
VSS
VCC
I/O11
I/O10
I/O9
I/O8
NC
A8
A9
A10
A11
NC
Pin Definitions
Pin Number
Type
Description
1–5, 18–22, 24–27, 42–45 Input
A0–A16. Address Inputs
7–10, 13–16, 29–32, 35–38 Input/Output
I/O0–I/O15. Data lines. Used as input or output lines depending on operation
23
No Connect
NC. This pin is not connected to the die
17
Input/Control WE. When selected LOW, a WRITE is conducted. When selected HIGH, a READ is
conducted
6
Input/Control CE. When LOW, selects the chip. When HIGH, deselects the chip
40, 39
Input/Control Byte Write Select Inputs, active LOW. BHE controls I/O15–I/O8, BLE controls
I/O7–I/O0.
41
Input/Control OE. Output Enable. Controls the direction of the I/O pins. When LOW, the I/O pins
behave as outputs. When deasserted HIGH, I/O pins are tri-stated, and act as input
data pins
12, 34
Ground
11, 33
Power Supply VCC. Power supply for the device
VSS. Ground for the device
Notes:
2. NC pins are not connected on the die.
3. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = VCC(TYP)., TA = 25°C.
Document #: 001-06497 Rev. *A
Page 2 of 11
[+] Feedback
CY62137VN MoBL®
Maximum Ratings
Output Current into Outputs (LOW)............................. 20 mA
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with
Power Applied............................................. –55°C to +125°C
Static Discharge Voltage........................................... > 2001V
(per MIL-STD-883, Method 3015)
Latch-up Current..................................................... > 200 mA
Operating Range
Supply Voltage to Ground Potential ............... –0.5V to +4.6V
Range
Ambient
Temperature
VCC
DC Voltage Applied to Outputs
in High-Z State[4] ....................................–0.5V to VCC + 0.5V
Industrial
–40°C to +85°C
2.7V to 3.6V
DC Input Voltage[4] .................................–0.5V to VCC + 0.5V
Automotive-A
–40°C to +85°C
Automotive-E
–40°C to +125°C
Electrical Characteristics Over the Operating Range
-55
Parameter
-70
Test Conditions
Min.
2.4
VOL
Output HIGH Voltage VCC = 2.7V, IOH = –1.0 mA
Output LOW Voltage VCC = 2.7V, IOL = 2.1 mA
VIH
Input HIGH Voltage
2.2
VCC +
0.5V
VIL
Input LOW Voltage
–0.5
IIX
Input Leakage
Current
GND < VI < VCC
IOZ
Output Leakage
Current
GND < VO < VCC, Output Disabled
ICC
VCC Operating
Supply
Current
IOUT = 0 mA,
VCC = 3.6V Ind’l
f = fMAX = 1/tRC,
Auto-A/
CMOS Levels
Auto-E
7
IOUT = 0 mA,
f = 1 MHz,
CMOS Levels
1
VOH
ISB1
ISB2
Description
Typ.[3]
Max.
Min. Typ.[3] Max.
2.4
V
0.4
0.4
V
2.2
VCC +
0.5V
V
0.8
–0.5
0.8
V
–1
+1
–1
+1
µA
–1
+1
–1
+1
µA
7
15
mA
7
15
1
2
1
2
Ind’l
20
2
Auto-A/
Auto-E
Automatic CE
Power-down
Current—CMOS
Inputs
CE > VCC – 0.3V, VCC = 3.6V Ind’l
VIN > VCC – 0.3V
Auto-A/
or VIN < 0.3V,
Auto-E
f = fMAX
Automatic CE
Power-down
Current—CMOS
Inputs
CE > VCC – 0.3V VCC = 3.6V Ind’l/
VIN > VCC – 0.3V
Auto-A
or VIN < 0.3V,
f=0
Auto-E
Unit
100
mA
µA
100
100
1
15
1
15
1
15
1
20
µA
Capacitance[5]
Parameter
Description
CIN
Input Capacitance
COUT
Output Capacitance
Test Conditions
TA = 25°C, f = 1 MHz,
VCC = VCC(typ)
Max.
Unit
6
pF
8
pF
Thermal Resistance[5]
Parameter
ΘJA
ΘJC
Description
Test Conditions
Thermal Resistance (Junction to Ambient) Still Air, soldered on a 4.25 x 1.125 inch,
Thermal Resistance (Junction to Case) 2-layer printed circuit board
TSOPII
Unit
60
°C/W
22
°C/W
Notes:
4. VIL(min.) = –2.0V for pulse durations less than 20 ns.
5. Tested initially and after any design or process changes that may affect these parameters.
Document #: 001-06497 Rev. *A
Page 3 of 11
[+] Feedback
CY62137VN MoBL®
AC Test Loads and Waveforms
R1
R1
VCC
ALL INPUT PULSES
VCC
OUTPUT
VCC Typ
OUTPUT
INCLUDING
JIG AND
SCOPE
(a)
R2
5 pF
R2
30 pF
90%
10%
90%
10%
GND
INCLUDING
JIG AND
SCOPE
Fall Time:
1 V/ns
Rise Time:
1 V/ns
(b)
(c)
Equivalent to:
THÉVENIN EQUIVALENT
RTH
OUTPUT
Parameters
VTH
Value
Unit
R1
1105
Ohms
R2
1550
Ohms
RTH
645
Ohms
VTH
1.75
Volts
Data Retention Characteristics (Over the Operating Range)
Parameter
Description
VDR
VCC for Data Retention
ICCDR
Data Retention Current
tCDR[5]
Chip Deselect to Data
Retention Time
tR
Operation Recovery Time
Conditions
Typ.[3]
Min.
Max.
1.0
VCC = 1.0V, CE > VCC – 0.3V,
VIN > VCC – 0.3V or VIN < 0.3V;
No input may exceed VCC + 0.3V
Unit
V
Ind’l/Auto-A
0.5
Auto-E
7.5
µA
10
0
ns
tRC
ns
Data Retention Waveform
DATA RETENTION MODE
VCC
VCC(min.)
tCDR
VDR > 1.0 V
VCC(min.)
tR
CE
Document #: 001-06497 Rev. *A
Page 4 of 11
[+] Feedback
CY62137VN MoBL®
Switching Characteristics Over the Operating Range
[6]
55 ns
Parameter
Description
Min.
70 ns
Max.
Min.
Max.
Unit
Read Cycle
tRC
Read Cycle Time
55
tAA
Address to Data Valid
tOHA
Data Hold from Address Change
tACE
CE LOW to Data Valid
55
70
ns
tDOE
OE LOW to Data Valid
25
35
ns
[7]
tLZOE
OE LOW to Low-Z
55
10
OE HIGH to High-Z
ns
70
10
5
[7, 8]
tHZOE
70
ns
5
25
ns
ns
25
ns
CE LOW to
Low-Z[7]
tHZCE
CE HIGH to
High-Z[7, 8]
tPU
CE LOW to Power-up
tPD
CE HIGH to Power-down
55
70
ns
BHE / BLE LOW to Data Valid
55
70
ns
tLZCE
tDBE
tLZBE
(9)
tHZBE
Write
BHE / BLE LOW to Low-Z
10
10
25
0
25
0
5
BHE / BLE HIGH to High-Z
ns
ns
5
25
ns
ns
25
ns
Cycle[10, 11]
tWC
Write Cycle Time
55
70
ns
tSCE
CE LOW to Write End
45
60
ns
tAW
Address Set-up to Write End
45
60
ns
tHA
Address Hold from Write End
0
0
ns
tSA
Address Set-up to Write Start
0
0
ns
tPWE
WE Pulse Width
40
50
ns
tSD
Data Set-up to Write End
25
30
ns
tHD
Data Hold from Write End
0
0
ns
tHZWE
WE LOW to
High-Z[7, 8]
[7]
tLZWE
WE HIGH to Low-Z
tBW
BHE / BLE LOW to End of Write
20
25
ns
5
10
ns
50
60
ns
Notes:
6. Test conditions assume signal transition time of 5 ns or less, timing reference levels of 1.5V, input levels of 0 to VCC typ., and output loading of the specified
IOL/IOH and 30 pF load capacitance.
7. At any given temperature and voltage condition, tHZCE is less than tLZCE, tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any given device.
8. tHZOE, tHZCE, and tHZWE are specified with CL = 5 pF as in (b) of AC Test Loads. Transition is measured ±500 mV from steady-state voltage.
9. If both byte enables are toggled together this value is 10 ns.
10. The internal write time of the memory is defined by the overlap of CE LOW and WE LOW. Both signals must be LOW to initiate a write and either signal can
terminate a write by going HIGH. The data input set-up and hold timing should be referenced to the rising edge of the signal that terminates the write.
11. The minimum write cycle time for write cycle #3 (WE controlled, OE LOW) is the sum of tHZWE and tSD.
Document #: 001-06497 Rev. *A
Page 5 of 11
[+] Feedback
CY62137VN MoBL®
Switching Waveforms
Read Cycle No. 1[12, 13]
tRC
ADDRESS
tOHA
DATA OUT
tAA
PREVIOUS DATA VALID
DATA VALID
Read Cycle No. 2[13, 14]
tRC
CE
tPD
tHZCE
tACE
OE
tHZOE
tDOE
BHE/BLE
tLZOE
tHZBE
tDBE
tLZBE
DATA OUT
HIGH IMPEDANCE
HIGH
IMPEDANCE
DATA VALID
tLZCE
VCC
SUPPLY
CURRENT
tPU
ICC
50%
50%
ISB
Notes:
12. Device is continuously selected. OE, CE = VIL.
13. WE is HIGH for read cycle.
14. Address valid prior to or coincident with CE transition LOW.
Document #: 001-06497 Rev. *A
Page 6 of 11
[+] Feedback
CY62137VN MoBL®
Switching Waveforms (continued)
Write Cycle No. 1 (WE Controlled)[10, 15, 16]
tWC
ADDRESS
CE
tAW
tHA
tSA
WE
tPWE
tBW
BHE/BLE
OE
tSD
DATA I/O
tHD
DATAIN VALID
NOTE 17
tHZOE
Write Cycle No. 2 (CE Controlled)[10, 15, 16]
tWC
ADDRESS
tSCE
CE
tSA
tAW
BHE/BLE
WE
tHA
tBW
tPWE
tSD
DATA I/O
tHD
DATAIN VALID
Notes:
15. Data I/O is high-impedance if OE = VIH.
16. If CE goes HIGH simultaneously with WE HIGH, the output remains in a high-impedance state.
17. During this period, the I/Os are in output state and input signals should not be applied.
Document #: 001-06497 Rev. *A
Page 7 of 11
[+] Feedback
CY62137VN MoBL®
Switching Waveforms (continued)
Write Cycle No. 3 (WE Controlled, OE LOW)[11, 16]
tWC
ADDRESS
CE
tAW
tBW
BHE/BLE
WE
tHA
tSA
tSD
DATA I/O
tHD
DATAIN VALID
NOTE 17
tLZWE
tHZWE
Write Cycle No. 4 (BHE/BLE Controlled, OE LOW)[17]
tWC
ADDRESS
CE
tAW
tHA
tBW
BHE/BLE
tSA
WE
tSD
DATA I/O
DATAIN VALID
NOTE 17
tHZWE
Document #: 001-06497 Rev. *A
tHD
tLZWE
Page 8 of 11
[+] Feedback
CY62137VN MoBL®
Typical DC and AC Characteristics
Normalized Operating Current
vs. Supply Voltage
1.4
Standby Current vs. Supply Voltage
35
MoBL
30
1.2
MoBL
25
ISB (µA)
1.0
ICC
0.8
0.6
20
15
10
0.4
5
0.2
0.0
1.7
0
2.2
2.7
3.2
SUPPLY VOLTAGE (V)
1.0
3.7
2.7 2.8
3.7
1.9
SUPPLY VOLTAGE (V)
Access Time vs. Supply Voltage
80
MoBL
70
60
TAA (ns)
50
40
30
20
10
1.0
2.7 2.8
1.9
3.7
SUPPLY VOLTAGE (V)
Truth Table
CE
WE
OE
BHE
BLE
H
X
X
X
X
High-Z
High-Z
Deselect/Power-down
Standby (ISB)
X
X
X
H
H
High-Z
High-Z
Deselect/Power-down
Standby (ISB)
L
H
L
L
L
Data Out
Data Out
Read
Active (ICC)
L
H
L
H
L
High-Z
Data Out
Read
Active (ICC)
L
H
L
L
H
Data Out
High-Z
Read
Active (ICC)
L
H
H
X
X
High-Z
High-Z
Output Disabled
Active (ICC)
L
L
X
L
L
Data In
Data In
Write
Active (ICC)
L
L
X
H
L
High-Z
Data In
Write
Active (ICC)
L
L
X
L
H
Data In
High-Z
Write
Active (ICC)
Document #: 001-06497 Rev. *A
I/O8–I/O15
I/O0–I/O7
Mode
Power
Page 9 of 11
[+] Feedback
CY62137VN MoBL®
Ordering Information
Speed
(ns)
Ordering Code
Package
Diagram
Operating
Range
Package Type
55
CY62137VNLL-55ZXI
51-85087 44-pin TSOP II (Pb-free)
Industrial
70
CY62137VNLL-70ZXI
44-pin TSOP II (Pb-free)
Industrial
CY62137VNLL-70ZSXA
44-pin TSOP II (Pb-free)
Automotive-A
CY62137VNLL-70ZSXE
44-pin TSOP II (Pb-free)
Automotive-E
Please contact your local Cypress sales representative for availability of these parts
Package Diagram
44-Pin TSOP II (51-85087)
DIMENSION IN MM (INCH)
MAX
MIN.
PIN 1 I.D.
1
23
10.262 (0.404)
10.058 (0.396)
11.938 (0.470)
11.735 (0.462)
22
EJECTOR PIN
44
TOP VIEW
0.800 BSC
(0.0315)
OR E
K X A
SG
BOTTOM VIEW
0.400(0.016)
0.300 (0.012)
10.262 (0.404)
10.058 (0.396)
BASE PLANE
0.210 (0.0083)
0.120 (0.0047)
0°-5°
0.10 (.004)
0.150 (0.0059)
0.050 (0.0020)
1.194 (0.047)
0.991 (0.039)
18.517 (0.729)
18.313 (0.721)
SEATING
PLANE
0.597 (0.0235)
0.406 (0.0160)
51-85087-*A
MoBL is a registered trademark, and More Battery Life is a trademark, of Cypress Semiconductor Corporation. All product and
company names mentioned in this document are the trademarks of their respective holders.
Document #: 001-06497 Rev. *A
Page 10 of 11
© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
[+] Feedback
CY62137VN MoBL®
Document History Page
Document Title: CY62137VN MoBL® 2-Mbit (128K x 16) Static RAM
Document Number: 001-06497
REV.
ECN NO. Issue Date
Orig. of
Change
Description of Change
**
426503
See ECN
NXR
New Data Sheet
*A
488954
See ECN
NXR
Added Automotive product
Updated Ordering Information table
Document #: 001-06497 Rev. *A
Page 11 of 11
[+] Feedback
工商网监
湘ICP备2023018690号
