Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
portfolio.
Continuity of document content
The fact that Infineon offers the following product as part of the Infineon product
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.
www.infineon.com
CY7C1351G
4-Mbit (128K × 36) Flow-Through SRAM
with NoBL™ Architecture
4-Mbit (128K × 36) Flow-Through SRAM with NoBL™ Architecture
Features
Functional Description
■
Can support up to 133 MHz bus operations with zero wait states
❐ Data is transferred on every clock
The CY7C1351G is a 3.3 V, 128K × 36 synchronous flow-through
burst SRAM designed specifically to support unlimited true
back-to-back read/write operations without the insertion of wait
states. The CY7C1351G is equipped with the advanced No Bus
Latency™ (NoBL™) logic required to enable consecutive
Read/Write operations with data being transferred on every clock
cycle. This feature dramatically improves the throughput of data
through the SRAM, especially in systems that require frequent
write-read transitions.
■
Pin compatible and functionally equivalent to ZBT™ devices
■
Internally self-timed output buffer control to eliminate the need
to use OE
■
Registered inputs for flow-through operation
■
Byte write capability
■
128K × 36 common I/O architecture
■
2.5 V/3.3 V I/O power supply (VDDQ)
■
Fast clock-to-output times
❐ 6.5 ns (for 133 MHz device)
■
Clock enable (CEN) pin to suspend operation
■
Synchronous self-timed writes
■
Asynchronous output enable
■
Available in Pb-free 100-pin TQFP package
■
Burst capability – linear or interleaved burst order
Three synchronous chip enables (CE1, CE2, CE3) and an
asynchronous output enable (OE) provide for easy bank
selection and output tristate control. In order to avoid bus
contention, the output drivers are synchronously tristated during
the data portion of a write sequence.
■
Low standby power
For a complete list of related documentation, click here.
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. The clock input is qualified by the
clock enable (CEN) signal, which when deasserted suspends
operation and extends the previous clock cycle. Maximum
access delay from the clock rise is 6.5 ns (133-MHz device).
Write operations are controlled by the four byte write select
(BW[A:D]) and a write enable (WE) input. All writes are conducted
with on-chip synchronous self-timed write circuitry.
Selection Guide
Description
133 MHz
100 MHz
Unit
Maximum access time
6.5
8.0
ns
Maximum operating current
225
205
mA
Maximum CMOS standby current
40
40
mA
Errata: For information on silicon errata, see "Errata" on page 19. Details include trigger conditions, devices affected, and proposed workaround.
Cypress Semiconductor Corporation
Document Number: 38-05513 Rev. *R
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised January 9, 2018
CY7C1351G
Logic Block Diagram
ADDRESS
REGISTER
A0, A1, A
A1
D1
A0
D0
MODE
CLK
CEN
C
CE
ADV/LD
C
BURST
LOGIC
Q1 A1'
A0'
Q0
WRITE ADDRESS
REGISTER
ADV/LD
BWA
BWB
BWC
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
BWD
WRITE
DRIVERS
MEMORY
ARRAY
S
E
N
S
E
A
M
P
S
WE
OE
CE1
CE2
CE3
ZZ
Document Number: 38-05513 Rev. *R
D
A
T
A
S
T
E
E
R
I
N
G
O
U
T
P
U
T
B
U
F
F
E
R
S
DQs
DQPA
DQPB
DQPC
DQPD
E
INPUT
E
REGISTER
READ LOGIC
SLEEP
Control
Page 2 of 23
CY7C1351G
Contents
Pin Configurations ........................................................... 4
Pin Definitions .................................................................. 5
Functional Overview ........................................................ 7
Single Read Accesses ................................................ 7
Burst Read Accesses .................................................. 7
Single Write Accesses ................................................. 7
Burst Write Accesses .................................................. 7
Sleep Mode ................................................................. 7
Linear Burst Address Table ......................................... 8
Interleaved Burst Address Table ................................. 8
ZZ Mode Electrical Characteristics .............................. 8
Truth Table ........................................................................ 9
Partial Truth Table for Read/Write .................................. 9
Maximum Ratings ........................................................... 10
Operating Range ............................................................. 10
Electrical Characteristics ............................................... 10
Capacitance .................................................................... 11
Thermal Resistance ........................................................ 11
AC Test Loads and Waveforms ..................................... 12
Document Number: 38-05513 Rev. *R
Switching Characteristics .............................................. 13
Switching Waveforms .................................................... 14
Ordering Information ...................................................... 16
Ordering Code Definitions ......................................... 16
Package Diagrams .......................................................... 17
Acronyms ........................................................................ 18
Document Conventions ................................................. 18
Units of Measure ....................................................... 18
Errata ............................................................................... 19
Part Numbers Affected .............................................. 19
Product Status ........................................................... 19
Ram9 NoBL ZZ Pin Issues Errata Summary ............. 19
Document History Page ................................................. 20
Sales, Solutions, and Legal Information ...................... 23
Worldwide Sales and Design Support ....................... 23
Products .................................................................... 23
PSoC® Solutions ...................................................... 23
Cypress Developer Community ................................. 23
Technical Support ..................................................... 23
Page 3 of 23
CY7C1351G
Pin Configurations
VSS
CLK
WE
CEN
OE
ADV/LD
90
89
88
87
86
85
44
45
46
47
48
49
50
A
A
A
A
A
A
A
43
42
NC/72M
NC/36M
41
VDD
A
VDD
91
40
39
NC/144M
VSS
38
36
A1
37
35
A
A0
34
NC/288M
33
A
81
CE3
92
82
BWA
93
NC/9M
BWB
94
A
BWC
95
83
BWD
96
84
CE2
97
NC/18M
CE1
98
A
A
BYTE D
32
NC
VSS
DQD
DQD
VDDQ
VSS
DQD
DQD
DQD
DQD
VSS
VDDQ
DQD
DQD
DQPD
A
VDD
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
CY7C1351G
31
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
BYTE C
DQPC
DQC
DQC
VDDQ
VSS
DQC
DQC
DQC
DQC
VSS
VDDQ
DQC
DQC
99
100
A
Figure 1. 100-pin TQFP (14 × 20 × 1.4 mm) pinout [1]
DQPB
DQB
DQB
VDDQ
VSS
DQB
DQB
DQB
DQB
VSS
VDDQ
DQB
DQB
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSS
DQA
DQA
DQA
DQA
VSS
VDDQ
DQA
DQA
DQPA
BYTE B
BYTE A
Note
1. Errata: The ZZ pin (Pin 64) needs to be externally connected to ground. For more information, see "Errata" on page 19.
Document Number: 38-05513 Rev. *R
Page 4 of 23
CY7C1351G
Pin Definitions
Name
I/O
Description
A0, A1, A
InputAddress inputs used to select one of the 128 K address locations. Sampled at the rising edge of
synchronous the CLK. A[1:0] are fed to the two-bit burst counter.
BW[A:D]
InputByte write inputs, active LOW. Qualified with WE to conduct writes to the SRAM. Sampled on the rising
synchronous edge of CLK.
WE
InputWrite enable input, active LOW. Sampled on the rising edge of CLK if CEN is active LOW. This signal
synchronous must be asserted LOW to initiate a write sequence.
ADV/LD
InputAdvance/load input. Used to advance the on-chip address counter or load a new address. When HIGH
synchronous (and CEN is asserted LOW) the internal burst counter is advanced. When LOW, a new address can be
loaded into the device for an access. After being deselected, ADV/LD should be driven LOW in order to
load a new address.
CLK
Input-clock
Clock input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN. CLK is
only recognized if CEN is active LOW.
CE1
InputChip enable 1 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE2,
synchronous and CE3 to select/deselect the device.
CE2
InputChip enable 2 input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with CE1
synchronous and CE3 to select/deselect the device.
CE3
InputChip enable 3 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE1
synchronous and CE2 to select/deselect the device.
OE
InputOutput enable, asynchronous input, active LOW. Combined with the synchronous logic block inside
asynchronous the device to control the direction of the I/O pins. When LOW, the I/O pins are allowed to behave as
outputs. When deasserted HIGH, I/O pins are tristated, and act as input data pins. OE is masked during
the data portion of a write sequence, during the first clock when emerging from a deselected state, when
the device has been deselected.
CEN
InputClock enable input, active LOW. When asserted LOW the clock signal is recognized by the SRAM.
synchronous When deasserted HIGH the clock signal is masked. Since deasserting CEN does not deselect the device,
CEN can be used to extend the previous cycle when required.
ZZ[2]
InputZZ “sleep” input. This active HIGH input places the device in a non-time critical “sleep” condition with data
asynchronous integrity preserved. During normal operation, this pin has to be low or left floating. ZZ pin has an internal
pull-down.
Note
2. Errata: The ZZ pin (Pin 64) needs to be externally connected to ground. For more information, see "Errata" on page 19.
Document Number: 38-05513 Rev. *R
Page 5 of 23
CY7C1351G
Pin Definitions (continued)
Name
I/O
Description
DQs
I/OBidirectional data I/O lines. As inputs, they feed into an on-chip data register that is triggered by the
synchronous rising edge of CLK. As outputs, they deliver the data contained in the memory location specified by
address during the clock rise of the read cycle. The direction of the pins is controlled by OE and the
internal control logic. When OE is asserted LOW, the pins can behave as outputs. When HIGH, DQs and
DQP[A:D] are placed in a tristate condition. The outputs are automatically tristated during the data portion
of a write sequence, during the first clock when emerging from a deselected state, and when the device
is deselected, regardless of the state of OE.
DQP[A:D]
I/OBidirectional data parity I/O lines. Functionally, these signals are identical to DQs. During write
synchronous sequences, DQP[A:D] is controlled by BW[A:D] correspondingly.
MODE
VDD
VDDQ
Input
strap pin
Mode input. Selects the burst order of the device. When tied to GND selects linear burst sequence.
When tied to VDD or left floating selects interleaved burst sequence.
Power supply Power supply inputs to the core of the device.
I/O power
supply
Power supply for the I/O circuitry.
VSS
Ground
NC
–
No connects. Not Internally connected to the die.
NC/9M,
NC/18M,
NC/36M,
NC/72M,
NC/144M,
NC/288M,
NC/576M,
NC/1G
–
No connects. Not internally connected to the die. NC/9M, NC/18M, NC/36M, NC/72M, NC/144M,
NC/288M, NC/576M and NC/1G are address expansion pins are not internally connected to the die.
Ground for the device.
Document Number: 38-05513 Rev. *R
Page 6 of 23
CY7C1351G
Functional Overview
Single Write Accesses
The CY7C1351G is a synchronous flow-through burst SRAM
designed specifically to eliminate wait states during write-read
transitions. All synchronous inputs pass through input registers
controlled by the rising edge of the clock. The clock signal is
qualified with the clock enable input signal (CEN). If CEN is
HIGH, the clock signal is not recognized and all internal states
are maintained. All synchronous operations are qualified with
CEN. Maximum access delay from the clock rise (tCDV) is 6.5 ns
(133-MHz device).
Write access are initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are all asserted active, and (3) the write signal WE is
asserted LOW. The address presented to the address bus is
loaded into the address register. The write signals are latched
into the control logic block. The data lines are automatically
tristated regardless of the state of the OE input signal. This
allows the external logic to present the data on DQs and
DQP[A:D].
Accesses can be initiated by asserting all three chip enables
(CE1, CE2, CE3) active at the rising edge of the clock. If clock
enable (CEN) is active LOW and ADV/LD is asserted LOW, the
address presented to the device will be latched. The access can
either be a read or write operation, depending on the status of
the write enable (WE). BW[A:D] can be used to conduct byte write
operations.
Write operations are qualified by the write enable (WE). All writes
are simplified with on-chip synchronous self-timed write circuitry.
Three synchronous chip enables (CE1, CE2, CE3) and an
asynchronous output enable (OE) simplify depth expansion. All
operations (reads, writes, and deselects) are pipelined. ADV/LD
should be driven LOW once the device has been deselected in
order to load a new address for the next operation.
Single Read Accesses
A read access is initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are all asserted active, (3) the write enable input signal
WE is deasserted HIGH, and (4) ADV/LD is asserted LOW. The
address presented to the address inputs is latched into the
address register and presented to the memory array and control
logic. The control logic determines that a read access is in
progress and allows the requested data to propagate to the
output buffers. The data is available within 6.5 ns (133-MHz
device) provided OE is active LOW. After the first clock of the
read access, the output buffers are controlled by OE and the
internal control logic. OE must be driven LOW in order for the
device to drive out the requested data. On the subsequent clock,
another operation (read/write/deselect) can be initiated. When
the SRAM is deselected at clock rise by one of the chip enable
signals, its output will be tristated immediately.
Burst Read Accesses
The CY7C1351G has an on-chip burst counter that allows the
user the ability to supply a single address and conduct up to four
reads without reasserting the address inputs. ADV/LD must be
driven LOW in order to load a new address into the SRAM, as
described in the Single Read Accesses section above. The
sequence of the burst counter is determined by the MODE input
signal. A LOW input on MODE selects a linear burst mode, a
HIGH selects an interleaved burst sequence. Both burst
counters use A0 and A1 in the burst sequence, and will wrap
around when incremented sufficiently. A HIGH input on ADV/LD
will increment the internal burst counter regardless of the state
of chip enable inputs or WE. WE is latched at the beginning of a
burst cycle. Therefore, the type of access (read or write) is
maintained throughout the burst sequence.
Document Number: 38-05513 Rev. *R
On the next clock rise the data presented to DQs and DQP[A:D]
(or a subset for byte write operations, see truth table for details)
inputs is latched into the device and the write is complete.
Additional accesses (read/write/deselect) can be initiated on this
cycle.
The data written during the write operation is controlled by
BW[A:D] signals. The CY7C1351G provides byte write capability
that is described in the truth table. Asserting the write enable
input (WE) with the selected byte write select input will selectively
write to only the desired bytes. Bytes not selected during a byte
write operation will remain unaltered. A synchronous self-timed
write mechanism has been provided to simplify the write
operations. Byte write capability has been included in order to
greatly simplify read/modify/write sequences, which can be
reduced to simple byte write operations.
Because the CY7C1351G is a common I/O device, data should
not be driven into the device while the outputs are active. The
output enable (OE) can be deasserted HIGH before presenting
data to the DQs and DQP[A:D] inputs. Doing so will tristate the
output drivers. As a safety precaution, DQs and DQP[A:D].are
automatically tristated during the data portion of a write cycle,
regardless of the state of OE.
Burst Write Accesses
The CY7C1351G has an on-chip burst counter that allows the
user the ability to supply a single address and conduct up to four
Write operations without reasserting the address inputs. ADV/LD
must be driven LOW in order to load the initial address, as
described in the Single Write Accesses section above. When
ADV/LD is driven HIGH on the subsequent clock rise, the chip
enables (CE1, CE2, and CE3) and WE inputs are ignored and the
burst counter is incremented. The correct BW[A:D] inputs must be
driven in each cycle of the burst write, in order to write the correct
bytes of data.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ places
the SRAM in a power conservation “sleep” mode. Two clock
cycles are required to enter into or exit from this “sleep” mode.
While in this mode, data integrity is guaranteed. Accesses
pending when entering the “sleep” mode are not considered valid
nor is the completion of the operation guaranteed. The device
must be deselected prior to entering the “sleep” mode. CE1, CE2,
and CE3, must remain inactive for the duration of tZZREC after the
ZZ input returns LOW.
Page 7 of 23
CY7C1351G
Linear Burst Address Table
Interleaved Burst Address Table
(MODE = GND)
(MODE = Floating or VDD)
First
Address
A1:A0
Second
Address
A1:A0
Third
Address
A1:A0
Fourth
Address
A1:A0
First
Address
A1:A0
Second
Address
A1:A0
Third
Address
A1:A0
00
01
01
10
Fourth
Address
A1:A0
10
11
00
01
10
11
11
00
01
00
11
10
10
11
00
01
10
11
00
01
11
00
01
10
11
10
01
00
ZZ Mode Electrical Characteristics
Parameter
Description
Test Conditions
Min
Max
Unit
IDDZZ
Sleep mode standby current
ZZ > VDD 0.2 V
–
40
mA
tZZS
Device operation to ZZ
ZZ > VDD 0.2 V
–
2tCYC
ns
tZZREC
ZZ recovery time
ZZ < 0.2 V
2tCYC
–
ns
tZZI
ZZ active to sleep current
This parameter is sampled
–
2tCYC
ns
tRZZI
ZZ inactive to exit sleep current
This parameter is sampled
0
–
ns
Document Number: 38-05513 Rev. *R
Page 8 of 23
CY7C1351G
Truth Table
The truth table for CY7C1351G follows. [3, 4, 5, 6, 7, 8, 9]
Operation
Address Used CE1 CE2 CE3 ZZ ADV/LD WE BWX OE CEN CLK
DQ
Deselect cycle
None
H
X
X
L
L
X
X
X
L
L->H
Tristate
Deselect cycle
None
X
X
H
L
L
X
X
X
L
L->H
Tristate
Deselect cycle
None
X
L
X
L
L
X
X
X
L
L->H
Tristate
Continue deselect cycle
None
X
X
X
L
H
X
X
X
L
L->H
Tristate
External
L
H
L
L
L
H
X
L
L
L->H Data out (Q)
Next
X
X
X
L
H
X
X
L
L
L->H Data out (Q)
External
L
H
L
L
L
H
X
H
L
L->H
Tristate
Next
X
X
X
L
H
X
X
H
L
L->H
Tristate
External
L
H
L
L
L
L
L
X
L
L->H Data in (D)
WRITE cycle (continue burst)
Next
X
X
X
L
H
X
L
X
L
L->H Data in (D)
NOP/WRITE ABORT (begin burst)
None
L
H
L
L
L
L
H
X
L
L->H
Tristate
WRITE ABORT (continue burst)
Next
X
X
X
L
H
X
H
X
L
L->H
Tristate
Current
X
X
X
L
X
X
X
X
H
L->H
–
None
X
X
X
H
X
X
X
X
X
X
Tristate
READ cycle (begin burst)
READ cycle (continue burst)
NOP/DUMMY READ (begin burst)
DUMMY READ (continue burst)
WRITE cycle (begin burst)
IGNORE CLOCK EDGE (stall)
SLEEP MODE
Partial Truth Table for Read/Write
The Partial Truth Table for Read/Write for CY7C1351G follows. [3, 4, 10]
Function
WE
BWA
BWB
BWC
BWD
Read
H
X
X
X
X
Read
H
X
X
X
X
Write – no bytes written
L
H
H
H
H
Write byte A – (DQA and DQPA)
L
L
H
H
H
Write byte B – (DQB and DQPB)
L
H
L
H
H
Write byte C – (DQC and DQPC)
L
H
H
L
H
Write byte D – (DQD and DQPD)
L
H
H
H
L
Write all bytes
L
L
L
L
L
Notes
3. X = Don’t Care.” H = Logic HIGH, L = Logic LOW. BWx = L signifies at least one byte write select is active, BWx = valid signifies that the desired byte write selects
are asserted, see truth table for details.
4. Write is defined by BWX, and WE. See truth table for read/write.
5. When a write cycle is detected, all I/Os are tristated, even during byte writes.
6. The DQs and DQP[A:D] pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
7. CEN = H, inserts wait states.
8. Device will power-up deselected and the I/Os in a tristate condition, regardless of OE.
9. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQs and DQP[A:D] = tristate when OE is
inactive or when the device is deselected, and DQs and DQP[A:D] = data when OE is active.
10. Table only lists a partial listing of the byte write combinations. Any combination of BWX is valid. Appropriate write will be done based on which byte write is active.
Document Number: 38-05513 Rev. *R
Page 9 of 23
CY7C1351G
Maximum Ratings
DC input voltage ................................. –0.5 V to VDD + 0.5 V
Exceeding maximum ratings may shorten the useful life of the
device. User guidelines are not tested.
Storage temperature ................................ –65 °C to +150 °C
Ambient temperature with
power applied .......................................... –55 °C to +125 °C
Supply voltage on VDD relative to GND .......–0.5 V to +4.6 V
Current into outputs (LOW) ........................................ 20 mA
Static discharge voltage
(per MIL-STD-883, method 3015) .......................... > 2001 V
Latch up current ..................................................... > 200 mA
Operating Range
Supply voltage on VDDQ relative to GND ...... –0.5 V to +VDD
Range
DC voltage applied to outputs
in tristate ...........................................–0.5 V to VDDQ + 0.5 V
Ambient
Temperature (TA)
Commercial
0 °C to +70 °C
VDD
VDDQ
3.3 V – 5% / 2.5 V – 5% to
+ 10%
VDD
Electrical Characteristics
Over the Operating Range
Parameter [11, 12]
Description
Test Conditions
VDD
Power supply voltage
VDDQ
I/O supply voltage
VOH
Output HIGH voltage
VOL
Output LOW voltage
For 3.3 V I/O, IOL= 8.0 mA
VIH
Input HIGH voltage
For 3.3 V I/O
Input HIGH voltage
VIL
Input LOW voltage[11]
voltage[11]
For 2.5 V I/O
Min
Input LOW
Unit
3.135
3.6
V
For 3.3 V I/O
3.135
VDD
V
For 2.5 V I/O
2.375
2.625
V
For 3.3 V I/O, IOH = –4.0 mA
2.4
–
V
For 2.5 V I/O, IOH = –1.0 mA
2.0
–
V
–
0.4
V
For 2.5 V I/O, IOL= 1.0 mA
IX
Max
–
0.4
V
2.0
VDD + 0.3
V
For 2.5 V I/O
1.7
VDD + 0.3
V
For 3.3 V I/O
–0.3
0.8
V
–0.3
0.7
V
Input leakage current except ZZ GND < VI < VDDQ
and MODE
5
5
A
Input current of MODE
Input = VSS
–30
–
A
Input = VDD
–
5
A
Input current of ZZ
Input = VSS
–5
–
A
Input = VDD
–
30
A
IOZ
Output leakage current
GND < VI < VDDQ, output disabled
–5
5
A
IDD
VDD operating supply current
VDD = Max, IOUT = 0 mA,
f = fMAX = 1/tCYC
7.5-ns cycle,
133 MHz
–
225
mA
10-ns cycle,
100 MHz
–
205
mA
7.5-ns cycle,
133 MHz
–
90
mA
10-ns cycle,
100 MHz
–
80
mA
–
40
mA
ISB1
ISB2
Automatic CE power-down
current – TTL inputs
Automatic CE power-down
current – CMOS inputs
VDD = Max, device deselected,
VIN > VIH or VIN VIL, f = fMAX,
inputs switching
VDD = Max, device deselected, All speeds
VIN > VDD – 0.3 V or VIN < 0.3 V,
f = 0, inputs static
Notes
11. Overshoot: VIH(AC) < VDD +1.5 V (Pulse width less than tCYC/2), undershoot: VIL(AC) > –2 V (Pulse width less than tCYC/2).
12. TPower-up: Assumes a linear ramp from 0 V to VDD(min.) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
Document Number: 38-05513 Rev. *R
Page 10 of 23
CY7C1351G
Electrical Characteristics (continued)
Over the Operating Range
Parameter [11, 12]
ISB3
Description
Automatic CE power-down
current – CMOS inputs
Automatic CE power-down
current – TTL inputs
ISB4
Test Conditions
Min
Max
Unit
VDD = Max, device deselected, 7.5-ns cycle,
VIN > VDDQ – 0.3 V or VIN < 0.3 V, 133 MHz
f = fMAX, inputs switching
10-ns cycle,
100 MHz
–
75
mA
–
65
mA
–
45
mA
VDD = Max, device deselected,
VIN > VIH or V IN < VIL,
f = 0, inputs static
All speeds
Capacitance
Parameter [13]
Description
CIN
Input capacitance
CCLOCK
Clock input capacitance
CI/O
I/O capacitance
100-pin TQFP
Max
Unit
5
pF
5
pF
5
pF
Test Conditions
100-pin TQFP
Package
Unit
Test conditions follow standard test methods and
procedures for measuring thermal impedance, per
EIA/JESD51.
30.32
°C/W
6.85
°C/W
Test Conditions
TA = 25 °C, f = 1 MHz,
VDD = 3.3 V, VDDQ=3.3 V
Thermal Resistance
Parameter [13]
Description
JA
Thermal resistance
(junction to ambient)
JC
Thermal resistance
(junction to case)
Note
13. Tested initially and after any design or process changes that may affect these parameters.
Document Number: 38-05513 Rev. *R
Page 11 of 23
CY7C1351G
AC Test Loads and Waveforms
Figure 2. AC Test Loads and Waveforms
3.3 V I/O Test Load
R = 317
3.3 V
OUTPUT
OUTPUT
RL = 50
Z0 = 50
GND
5 pF
R = 351
VT = 1.5 V
INCLUDING
JIG AND
SCOPE
(a)
ALL INPUT PULSES
VDDQ
10%
90%
10%
90%
1ns
1ns
(c)
(b)
2.5 V I/O Test Load
R = 1667
2.5 V
OUTPUT
OUTPUT
RL = 50
Z0 = 50
GND
5 pF
R = 1538
VT = 1.25 V
(a)
Document Number: 38-05513 Rev. *R
ALL INPUT PULSES
VDDQ
INCLUDING
JIG AND
SCOPE
(b)
10%
90%
10%
90%
1ns
1ns
(c)
Page 12 of 23
CY7C1351G
Switching Characteristics
Over the Operating Range
Parameter [14, 15]
tPOWER
Description
VDD(typical) to the first access [16]
-133
-100
Unit
Min
Max
Min
Max
1
–
1
–
ms
Clock
tCYC
Clock cycle time
7.5
–
10
–
ns
tCH
Clock HIGH
2.5
–
4.0
–
ns
tCL
Clock LOW
2.5
–
4.0
–
ns
Output Times
tCDV
Data output valid after CLK rise
–
6.5
–
8.0
ns
tDOH
Data output hold after CLK rise
2.0
–
2.0
–
ns
tCLZ
Clock to low Z
[17, 18, 19]
0
–
0
–
ns
tCHZ
Clock to high Z 17, 18, 19]
–
3.5
–
3.5
ns
tOEV
OE LOW to output valid
–
3.5
–
3.5
ns
0
–
0
–
ns
–
3.5
–
3.5
ns
tOELZ
tOEHZ
OE LOW to output low Z
[17, 18, 19]
OE HIGH to output high Z
[17, 18, 19]
Set-up Times
tAS
Address set-up before CLK rise
1.5
–
2.0
–
ns
tALS
ADV/LD set-up before CLK rise
1.5
–
2.0
–
ns
tWES
WE, BWX set-up before CLK rise
1.5
–
2.0
–
ns
tCENS
CEN set-up before CLK rise
1.5
–
2.0
–
ns
tDS
Data input set-up before CLK rise
1.5
–
2.0
–
ns
tCES
Chip enable set-up before CLK rise
1.5
–
2.0
–
ns
tAH
Address hold after CLK rise
0.5
–
0.5
–
ns
tALH
ADV/LD hold after CLK rise
0.5
–
0.5
–
ns
tWEH
WE, BWX hold after CLK rise
0.5
–
0.5
–
ns
tCENH
CEN hold after CLK rise
0.5
–
0.5
–
ns
tDH
Data input hold after CLK rise
0.5
–
0.5
–
ns
tCEH
Chip enable hold after CLK rise
0.5
–
0.5
–
ns
Hold Times
Notes
14. Timing reference level is 1.5 V when VDDQ = 3.3 V and is 1.25 V when VDDQ = 2.5 V.
15. Test conditions shown in (a) of Figure 2 on page 12, unless otherwise noted.
16. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD(minimum) initially before a read or write operation can
be initiated.
17. tCHZ, tCLZ, tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of Figure 2 on page 12. Transition is measured ±200 mV from steady-state voltage.
18. At any given voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data
bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve
tristate prior to low Z under the same system conditions.
19. This parameter is sampled and not 100% tested.
Document Number: 38-05513 Rev. *R
Page 13 of 23
CY7C1351G
Switching Waveforms
Figure 3. Read/Write Waveforms [20, 21, 22]
1
2
3
tCYC
4
5
6
7
8
9
A5
A6
A7
10
CLK
tCENS
tCENH
tCES
tCEH
tCH
tCL
CEN
CE
ADV/LD
WE
BW[A:D]
A1
ADDRESS
tAS
A2
A4
A3
tCDV
tAH
tDOH
tCLZ
DQ
D(A1)
tDS
D(A2)
Q(A3)
D(A2+1)
tOEV
Q(A4+1)
Q(A4)
tDH
tOELZ
WRITE
D(A1)
WRITE
D(A2)
D(A5)
Q(A6)
D(A7)
WRITE
D(A7)
DESELECT
tOEHZ
OE
COMMAND
tCHZ
BURST
WRITE
D(A2+1)
READ
Q(A3)
READ
Q(A4)
DON’T CARE
BURST
READ
Q(A4+1)
tDOH
WRITE
D(A5)
READ
Q(A6)
UNDEFINED
Notes
20. For this waveform ZZ is tied LOW.
21. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
22. Order of the burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved). Burst operations are optional.
Document Number: 38-05513 Rev. *R
Page 14 of 23
CY7C1351G
Switching Waveforms (continued)
Figure 4. NOP, STALL and DESELECT Cycles [23, 24, 25]
1
2
A1
A2
3
4
5
A3
A4
6
7
8
9
10
CLK
CEN
CE
ADV/LD
WE
BW[A:D]
ADDRESS
A5
tCHZ
D(A1)
DQ
Q(A2)
Q(A3)
D(A4)
Q(A5)
tDOH
COMMAND
WRITE
D(A1)
READ
Q(A2)
STALL
READ
Q(A3)
WRITE
D(A4)
DON’T CARE
STALL
NOP
READ
Q(A5)
DESELECT
CONTINUE
DESELECT
UNDEFINED
Figure 5. ZZ Mode Timing [26, 27]
CLK
t ZZ
ZZ
I
t ZZREC
t ZZI
SUPPLY
I DDZZ
t RZZI
ALL INPUTS
(except ZZ)
Outputs (Q)
DESELECT or READ Only
High-Z
DON’T CARE
Notes
23. For this waveform ZZ is tied LOW.
24. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
25. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrates CEN being used to create a pause. A write is not performed during this cycle.
26. Device must be deselected when entering ZZ mode. See truth table for all possible signal conditions to deselect the device.
27. DQs are in high Z when exiting ZZ sleep mode.
Document Number: 38-05513 Rev. *R
Page 15 of 23
CY7C1351G
Ordering Information
Cypress offers other versions of this type of product in many different configurations and features. The following table contains only
the list of parts that are currently available.
For a complete listing of all options, visit the Cypress website at www.cypress.com and refer to the product summary page at
http://www.cypress.com/products or contact your local sales representative.
Cypress maintains a worldwide network of offices, solution centers, manufacturer's representatives and distributors. To find the office
closest to you, visit us at http://www.cypress.com/go/datasheet/offices.
Speed
(MHz)
Package
Diagram
Ordering Code
Part and Package Type
100
CY7C1351G-100AXC
51-85050 100-pin TQFP (14 × 20 × 1.4 mm) Pb-free
133
CY7C1351G-133AXC
51-85050 100-pin TQFP (14 × 20 × 1.4 mm) Pb-free
Operating
Range
Commercial
Ordering Code Definitions
CY 7
C
1351
G - XXX
A
X C
Temperature Range:
C = Commercial = 0 °C to 70 °C
X = Pb-free
Package Type:
A = 100-pin TQFP
Speed Grade: XXX = 100 MHz or 133 MHz
Process Technology: G 90 nm
Part Identifier: 1351 = FT, 128Kb × 36 (4Mb)
Technology Code: C = CMOS
Marketing Code: 7 = SRAM
Company ID: CY = Cypress
Document Number: 38-05513 Rev. *R
Page 16 of 23
CY7C1351G
Package Diagrams
Figure 6. 100-pin TQFP (14 × 20 × 1.4 mm) A100RA Package Outline, 51-85050
ș2
ș1
ș
SYMBOL
DIMENSIONS
MIN. NOM. MAX.
A
1.60
0.15
NOTE:
1. ALL DIMENSIONS ARE IN MILLIMETERS.
2. BODY LENGTH DIMENSION DOES NOT
A1
0.05
A2
1.35 1.40 1.45
D
15.80 16.00 16.20
MOLD PROTRUSION/END FLASH SHALL
D1
13.90 14.00 14.10
E
21.80 22.00 22.20
NOT EXCEED 0.0098 in (0.25 mm) PER SIDE.
BODY LENGTH DIMENSIONS ARE MAX PLASTIC
E1
19.90 20.00 20.10
R1
0.08
0.20
R2
0.08
0.20
ș
0°
7°
ș1
0°
ș2
11°
13°
12°
b
0.22 0.30 0.38
L
0.45 0.60 0.75
L2
L3
e
BODY SIZE INCLUDING MOLD MISMATCH.
3. JEDEC SPECIFICATION NO. REF: MS-026.
0.20
c
L1
INCLUDE MOLD PROTRUSION/END FLASH.
1.00 REF
0.25 BSC
0.20
0.65 TYP
51-85050 *G
Document Number: 38-05513 Rev. *R
Page 17 of 23
CY7C1351G
Acronyms
Document Conventions
Acronym
Description
Units of Measure
CMOS
Complementary Metal Oxide Semiconductor
CE
Chip Enable
°C
degree Celsius
CEN
Clock Enable
MHz
megahertz
EIA
Electronics Industries Alliance
µA
microampere
I/O
Input/Output
mA
milliampere
JEDEC
Joint Electron Devices Engineering Council
mm
millimeter
NoBL
No Bus Latency
ms
millisecond
OE
Output Enable
SRAM
Static Random Access Memory
TQFP
Thin Quad Flat Pack
TTL
Transistor-Transistor Logic
WE
Write Enable
Document Number: 38-05513 Rev. *R
Symbol
Unit of Measure
ns
nanosecond
%
percent
pF
picofarad
V
volt
W
watt
Page 18 of 23
CY7C1351G
Errata
This section describes the Ram9 NoBL ZZ pin issue. Details include trigger conditions, the devices affected, proposed workaround
and silicon revision applicability. Please contact your local Cypress sales representative if you have further questions.
Part Numbers Affected
Density & Revision
Package Type
Operating Range
4Mb-Ram9 NoBL™ SRAMs: CY7C135*G
100-pin TQFP
Commercial
Product Status
All of the devices in the Ram9 4Mb NoBL family are qualified and available in production quantities.
Ram9 NoBL ZZ Pin Issues Errata Summary
The following table defines the errata applicable to available Ram9 4Mb NoBL family devices.
Item
1.
Issues
ZZ Pin
Description
Device
When asserted HIGH, the ZZ pin places
device in a “sleep” condition with data integrity
preserved.The ZZ pin currently does not have
an internal pull-down resistor and hence
cannot be left floating externally by the user
during normal mode of operation.
4M-Ram9 (90 nm)
Fix Status
For the 4M Ram9 (90 nm)
devices, there is no plan to fix
this issue.
1. ZZ Pin Issue
■
PROBLEM DEFINITION
The problem occurs only when the device is operated in the normal mode with ZZ pin left floating. The ZZ pin on the SRAM
device does not have an internal pull-down resistor. Switching noise in the system may cause the SRAM to recognize a HIGH
on the ZZ input, which may cause the SRAM to enter sleep mode. This could result in incorrect or undesirable operation of the
SRAM.
■
TRIGGER CONDITIONS
Device operated with ZZ pin left floating.
■
SCOPE OF IMPACT
When the ZZ pin is left floating, the device delivers incorrect data.
■
WORKAROUND
Tie the ZZ pin externally to ground.
■
FIX STATUS
For the 4M Ram9 (90 nm) devices, there is no plan to fix this issue.
Document Number: 38-05513 Rev. *R
Page 19 of 23
CY7C1351G
Document History Page
Document Title: CY7C1351G, 4-Mbit (128K × 36) Flow-Through SRAM with NoBL™ Architecture
Document Number: 38-05513
Rev.
ECN No.
Orig. of
Change
Submission
Date
**
224360
RKF
05/17/2004
New data sheet.
*A
276690
VBL
10/14/2004
Removed 66 MHz frequency related information in all instances across the
document.
Updated Ordering Information (Updated part numbers; added comment of
availability of BG lead-free package).
*B
333626
SYT
03/15/2005
Updated Features (Removed 117 MHz frequency related information).
Updated Selection Guide (Removed 117 MHz frequency related information).
Updated Pin Configurations (Modified Address Expansion balls in the pinouts
for 100-pin TQFP and 119-ball BGA Packages as per JEDEC standards).
Updated Pin Definitions.
Updated Functional Overview (Updated ZZ Mode Electrical Characteristics
(Replaced “Snooze” with “Sleep”)).
Updated Electrical Characteristics (Updated Test Conditions of VOL, VOH
parameters, removed 117 MHz frequency related information).
Updated Truth Table (Replaced “Snooze” with “Sleep”).
Updated Thermal Resistance (Replaced values of JA and JC parameters
from TBD to respective Thermal Values for all Packages).
Updated Switching Characteristics (Removed 117 MHz frequency related
information).
Updated Ordering Information (By shading and unshading MPNs as per
availability; changed the package name for 100-pin TQFP from A100RA to
A101).
*C
418633
RXU
01/06/2006
Changed status from Preliminary to Final.
Changed address of Cypress Semiconductor Corporation from “3901 North
First Street” to “198 Champion Court”.
Updated Electrical Characteristics (Updated Note 12 (Modified test condition
from VDDQ < VDD to VDDQ < VDD), splitted VDDQ parameter into two rows (one
for 3.3 V I/O, another for 2.5 V I/O),
Updated Test Conditions of VOL, VOH parameters
(Changed Typo in Test Condition of VOH parameter
from “for 3.3 V I/O” to “for 3.3 V I/O, IOH = –4.0 mA” and
from “for 2.5 V I/O” to “for 2.5 V I/O, IOH = –1.0 mA”,
changed Typo in Test Condition of VOL parameter
from “for 3.3 V I/O, IOH = –4.0 mA” to “for 3.3 V I/O, IOH = 8.0 mA” and
from “for 2.5 V I/O, IOH = –1.0 mA” to “for 2.5 V I/O, IOH = 1.0 mA”),
updated Test Conditions of VIH parameter
(Changed Typo in Test Condition of VIH parameter
from “for 3.3 V I/O, IOH = 8.0 mA” to “for 3.3 V I/O” and
from “for 2.5 V I/O, IOH =1.0 mA” to “for 2.5 V I/O”),
changed “Input Load Current except ZZ and MODE” to “Input Leakage Current
except ZZ and MODE”,
updated Test Conditions of IX parameter
(Changed Typo in Test Condition of IX parameter (Corresponding to Input Load
Current except ZZ and MODE) from “for 3.3 V” to “GND VI VDDQ”,
changed Typo in Test Condition of IX parameter (Corresponding to Input
Current of Mode) from “for 2.5 V I/O and “GND VI VDDQ” to Input = VSS and
Input = VDD respectively),
updated Test Conditions of ISB4 parameter
(Changed Typo in Test Condition of ISB4 parameter from “VIN VDDQ – 0.3 V
or VIN 0.3V” to “VIN VIH or VIN VIL”)).
Updated Ordering Information (Updated part numbers; replaced Package
Name column with Package Diagram in the Ordering Information table).
Updated Package Diagrams (spec 51-85050 (changed revision from *A to *B)).
Document Number: 38-05513 Rev. *R
Description of Change
Page 20 of 23
CY7C1351G
Document History Page (continued)
Document Title: CY7C1351G, 4-Mbit (128K × 36) Flow-Through SRAM with NoBL™ Architecture
Document Number: 38-05513
Rev.
ECN No.
Orig. of
Change
Submission
Date
*D
480124
VKN
07/14/2006
Updated Maximum Ratings (Added the Maximum Rating for Supply Voltage
on VDDQ Relative to GND).
Updated Ordering Information (Updated part numbers).
*E
2896584
NJY
03/20/2010
Updated Ordering Information (Updated part numbers).
Updated Package Diagrams:
spec 51-85050 – Changed revision from *B to *C.
spec 51-85115 – Changed revision from *B to *C.
*F
3033272
NJY
09/19/2010
Updated Ordering Information:
No change in part numbers.
Added Ordering Code Definitions.
Added Acronyms and Units of Measure.
Minor edits.
Updated to new template.
Completing Sunset Review.
Description of Change
*G
3067198
NJY
10/20/2010
Updated Ordering Information (Updated part numbers).
*H
3096309
NJY
11/28/2010
Updated Functional Description:
Updated description.
*I
3353119
PRIT
08/24/2011
Updated Functional Description (Updated the Note as “For best practice
recommendations, refer to SRAM System Guidelines.”).
Updated Package Diagrams (spec 51-85050 (changed revision from *C to *D)).
Completing Sunset Review.
*J
3616656
PRIT
05/14/2012
Updated Features (Removed 119-ball BGA package related information).
Updated Functional Description (Removed the Note “For best practice
recommendations, refer to SRAM System Guidelines.” and its reference).
Updated Pin Configurations (Removed 119-ball BGA package related
information).
Updated Operating Range (Removed Industrial Temperature Range).
Updated Capacitance (Removed 119-ball BGA package related information).
Updated Thermal Resistance (Removed 119-ball BGA package related
information).
Updated Package Diagrams (Removed 119-ball BGA package related
information (spec 51-85115 Rev. *C)).
*K
3767562
PRIT
10/05/2012
No technical updates.
Completing Sunset Review.
*L
3980362
PRIT
04/24/2013
Added Errata.
*M
4038283
PRIT
06/25/2013
Added Errata Footnotes.
Updated to new template.
*N
4146701
PRIT
10/04/2013
Updated Errata.
*O
4540469
PRIT
10/16/2014
Updated Package Diagrams:
spec 51-85050 – Changed revision from *D to *E.
Completing Sunset Review.
*P
4572829
PRIT
11/18/2014
Updated Functional Description:
Added “For a complete list of related documentation, click here.” at the end.
*Q
5508643
PRIT
11/03/2016
Updated Package Diagrams:
spec 51-85050 – Changed revision from *E to *F.
Updated to new template.
Completing Sunset Review.
Document Number: 38-05513 Rev. *R
Page 21 of 23
CY7C1351G
Document History Page (continued)
Document Title: CY7C1351G, 4-Mbit (128K × 36) Flow-Through SRAM with NoBL™ Architecture
Document Number: 38-05513
Rev.
ECN No.
Orig. of
Change
Submission
Date
*R
5999437
RMES
01/09/2018
Document Number: 38-05513 Rev. *R
Description of Change
Updated Ordering Information:
No change in part numbers.
Updated Ordering Code Definitions.
Updated Package Diagrams:
spec 51-85050 – Changed revision from *F to *G.
Updated to new template.
Completing Sunset Review.
Page 22 of 23
CY7C1351G
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
PSoC® Solutions
Products
Arm® Cortex® Microcontrollers
Automotive
cypress.com/arm
cypress.com/automotive
Clocks & Buffers
Interface
Internet of Things
Memory
cypress.com/clocks
cypress.com/interface
cypress.com/iot
cypress.com/memory
Microcontrollers
cypress.com/mcu
PSoC
cypress.com/psoc
Power Management ICs
Touch Sensing
USB Controllers
Wireless Connectivity
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6 MCU
Cypress Developer Community
Community | Projects | Video | Blogs | Training | Components
Technical Support
cypress.com/support
cypress.com/pmic
cypress.com/touch
cypress.com/usb
cypress.com/wireless
© Cypress Semiconductor Corporation, 2004-2018. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document,
including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other
intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress
hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to
modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users
(either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as
provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation
of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is
the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products
are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or
systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the
device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably
expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim,
damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other
liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 38-05513 Rev. *R
Revised January 9, 2018
ZBT is a trademark of Integrated Device Technology, Inc. NoBL and No Bus Latency are trademarks of Cypress Semiconductor Corporation.
Page 23 of 23